Obtain a Mounting Bracket Kit (1U or 0U) to rack mount your 1U Rackmount LED Console. Before installing the
Rackmount LED Console and other components in the rack, stabilize the rack in a permanent location. Start rack
mounting your equipment at the bottom of the rack, then work to the top. Avoid uneven loading or overloading of
racks.
CAUTION: Before installing systems in a rack, install front and side stabilizers on stand-alone racks or the
front stabilizer on racks joined to other racks. Failure to install stabilizers accordingly before installing systems
in a rack could cause the rack to tip over, potentially resulting in bodily injury under certain circumstances.
Therefore, always install the stabilizer(s) before installing components in the rack.
NOTE: Do not mount this product with the rear panel facing in the downward position towards the floor.
1U LED 1U 0U LED
1U 0U 1U LED LED
Installation Instructions | | | |
1U Rackmount LED
1U0U
Rackmount LED
Remove the screw from the front mounting bracket using a torx-head screwdriver, then remove the pins from the front and
rear mounting brackets using a flat-tipped screwdriver (1). Pull and rotate the rail latch subassemblies to remove them
from the mounting brackets (2). Attach the left and right mounting rails to the front vertical rack flanges using two pairs of
screws (3). Slide the left and right back brackets forward against the rear vertical rack flanges and attach them using two
pairs of screws (4).
(1) (2)
(3)
(4)
:
.
.
.
: .
(1) (2)
(3)
(4)
2
2
2
4
(Tooled)
(torx-head)
(1).
(2).
(3).
(4).
Dell 1U LED
Dell ReadyRails II
CD
NOTE: Ensure that the system is properly supported until the chassis rail members are inserted into the slide rails
on both sides. Pull the sliding rails out of the rack until they are fully extended. Align and insert the ends of the
chassis rail members into the ends of the rails. Push the system inward until the chassis rail members are fully
inserted. Pull and push the console tray in and out of the rack until it slides smoothly within the rack.
Dell 1U LED
Dell 1U LED
Dell ReadyRails II
Dell 1U LED
.
Dell 1U Rackmount LED 1
Dell ReadyRails II
, , CD
:
. .
.
.
.
Position the left and right rail end pieces labeled FRONT facing inward and orient each end piece to seat in the holes on
the front side of the vertical rack flanges. Align each end piece in the bottom and top holes of the desired U spaces until
the latch clicks into place (1). Engage the back end of the rail until it fully seats on the vertical rack flange and the latch
clicks into place (2).
From the back of the rack, cut the zip tie that secures the CMA to the back of the console tray. Swing the free end
of the CMA out to the bracket on the end of the left stationary rail and attach the arm to the bracket with the captive
screw on the end of the arm.
FRONT
U (1)
(2)
(CMA)
FRONT
U (1)
(2)
(CMA)
(CMA)
FRONT
U
1
CMA
CMA
(CMA)
CMA . CMA
.
(Tool-less)
w w w. d e l l . c o m | s u p p o r t . d e l l . c o m
CMA CMA
FRONT
. U
(1).
(2).
3
4
Installation Instructions
Installation Instructions | | | |
WARNING
To reduce the risk of electric shock or damage to your equipment:
Gently thread the cables through the cable channel on the CMA, then secure the cables to the slide rail, ensuring they
aren't pulled too tight (1).
Plug the power cord into a grounded (earthed) outlet that is easily
accessible at all times.
CMA (1)
(CMA)
(1)
CMA
(1)
CMA ,
(1).
From the back of the rack, unscrew the captive screw from the Cable Management Arm (CMA) to remove it from the rail.
Pull the console tray out until the slide rails are in a fully extended position (1). Press the blue tabs on each side of the
console tray (2). While pressing the tabs in Step 2, slide the console tray out of the rack (3).
(CMA)
(1) (2) 2
(3)
(CMA)
(1) (2) 2
(3)
CMA
(1)
(2)2
(3)
_____________________________________________________
_____________________________________________________
.
.
:
.
:
.
.
:
.
:
.
:
.
.
:
.
.
_____________________________________________________
At the front of the rack, pull the blue tab to release the lock (1). Repeat at the back of the rack and slide the rail out of the
rack (2).
:
.
(1) (2)
(1)(2)
2012 9
(Tool-less)
(1).
(2).
Installation Instructions
2012 9
Unscrew the two pairs of screws to detach the left and right brackets from the front vertical rack flanges (1). Unscrew the two
pairs of screws to detach the left and right mounting rails from the rear vertical rack flanges (2).
Dell Inc.
20129
(1)
(2)
.
2012 Dell Inc. All rights reserved.
Dell Inc. .
: Dell DELL Dell Inc. .
, . Dell Inc.
.
2012 9
1
2
2
1
(1).
(2).
____________________________________________________
1
2
www.dell.com | support.dell.com
(CMA) .
(1).
(2). 2
(3).
(Tooled)