FTPS
HTTP
** HTTPS
WEP2
TFTP
2 Refer to the exhibit. A new branch office has been added to the corporate network
and a new router is to be installed to allow branch office users to access the database
server at headquarters. How should the serial 0/0/0 interface of the new branch office
router be configured to connect to the headquarters router?
branch_23(config-if)# no shutdown
branch_23(config-if)# encapsulation ppp
branch_23(config-if)# ip address 192.168.5.33 255.255.255.240
3Which two commands ensure that any password that permits access to the privileged
EXEC mode is not shown in plain text when the configuration files are displayed?
(Choose two.)
if data segments are not received from the source, the destination requests that the
segments be resent.
If an acknowledgment of the transmitted segments is not received from the destination
in a predetermined amount of the time, the source resends the data.
** TCP uses the SYN-ACK portion of the three-way handshake to ensure that all data
has been received.
The TCP Protocol Interpreter process verifies the transmitted data at source and
destination.
routable translation
dynamic translation
static translation
** port address translation
** BGP
RIP
OSPF
EIGRP
8 Refer to the exhibit. The network administrator needs to configure the router with a
name. Which command will the administrator use to configure the router name?
to indicate the correct router interface that should be used to forward a segment
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
11Which two statements are true about the use of the debug ip rip command on a
Cisco router? (Choose two.)
** The debug ip rip command displays RIP routing activity in real time.
**The debug ip rip command can be issued at the user EXEC configuration mode.
The debug ip rip command displays a combination of the information that is displayed
by the show ip route and show ip protocols commands.
Because of router processor usage, the debug ip rip command should be used only
when necessary.
The debug ip rip command should be used instead of the show ip route command
whenever possible.
**DNS server
WINS server
**IP address
NetBIOS
** subnet mask
** default gateway
13A Catalyst 2960 switch has been taken out of storage to be used as a temporary
replacement for another switch that needs to be repaired. About a minute after the
switch has started, the SYST LED on the front of the switch transitions from blinking
green to amber. What is the meaning of the amber SYST LED?
15After an unsuccessful ping to the local router, the technician decides to investigate
the router. The technician observes that the lights and fan on the router are not
operational. In which layer of the OSI model is the problem most likely occurring?
transport
network
data link
** physical
17Refer to the exhibit. The network shown is connected using services from the same
ISP. How will the Fohi router dynamically learn routes to the 192.168.16.16/28,
192.168.16.32/28, and 192.168.16.64/28 subnetworks?
with BGP
**with a static route
with a directly connected route
with an interior routing protocol
18Refer to the exhibit. Which type of UTP cable should be used to connect Host A to
Switch1?
rollover
console
crossover
**straight-through
19When customers use credit cards to make purchases at a small business, a modem
is heard dialing a telephone number to transfer the transaction data to the central
office. What type of WAN serial connection is in use?
leased line
packet switched
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
** circuit switched
point-to-point
20 A user reports being unable to access the Internet. The help desk technician
employs a bottom-up approach to troubleshooting. The technician first has the user
check the patch cable connection from the PC to the wall, and then has the user verify
that the NIC has a green link light. What will the technician have the user do next?
Enter an IP address into the WWW browser address bar to see if DNS is at fault.
Use traceroute to identify the device along the path to the ISP that may be at fault.
** Verify the IP address, subnet, and gateway settings using ipconfig on the PC .
Connect to the user home router to check firewall settings for blocked TCP ports.
23Refer to the exhibit. Which two statements describe the data conversation shown?
(Choose two.)
** The data conversation was started by the HTTP application process running on the
client.
The data conversation is identified by TCP port 80 on the client.
The user started the data conversation by sending an e-mail.
The IP address of the Internet server is 192.168.17.43 .
**The Internet server will send data to port 8547 on the client.
sending echo requests from the source to the destination host to establish the presence
of the destination
determining the IP address of the destination host in preparation for data transfer
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
host address
network address
**broadcast address
multicast address
** misconfigured firewall
bad port on switch or hub
misconfigured IP addressing on the customer's workstation
wrong DNS server configured on the customer's workstation
wrong default gateway configured on the customer's workstation
27The show ip route command was executed on one of the routers shown in the
graphic and the following output was displayed:
C 192.168.4.0/24 is directly connected, Serial0/0
R 192.168.5.0/24 [120/1] via 192.168.4.2, 00:00:19, Serial0/0
R 192.168.1.0/24 [120/2] via 192.168.3.1, 00:00:20, Serial0/1
R 192.168.2.0/24 [120/2] via 192.168.3.1, 00:00:20, Serial0/1
C 192.168.3.0/24 is directly connected, Serial0/1
From which router was this command executed?
A
B
C
D
28Refer to the exhibit. Which two sets of commands are required to configure
passwords for all management ports on a Catalyst 2960 switch? (Choose two.)
30Refer to the graphic. Which command will configure a static route on Router A to
direct traffic from LAN A that is destined for LAN C?
31Which subnet masks could be used when subnetting a Class B IP address? (Choose
two.)
255.255.255.240
** 255.255.192.0
** 255.255.0.0
255.192.0.0
240.0.0.0
255.0.0.0
32 Refer to the exhibit. The network administrator has configured the RTA and RTB
interfaces. In order to allow hosts that are attached to RTA to reach the server that is
attached to RTB, a static route from RTA to the server LAN and a default route from
RTB back to RTA need to be configured. Which two commands will the
administrator use to accomplish these tasks on the two routers? (Choose two.)
33How do port filtering and access lists help provide network security?
34 Refer to the exhibit. The network administrator of the building in the graphic needs
to choose the type of cable best suited to add ServerB to the network. Which cable
type is the best choice?
STP
UTP
coaxial
**fiber optic
35What is used by a routing protocol to determine the best path to include in the
routing table?
Convergence time
Default distance
** Metric
Type of router
36Refer to the exhibit. Which IP addresses could be assigned to the hosts in the
diagram? (Choose two.)
192.168.65.31
192.168.65.32
** 192.168.65.35
** 192.168.65.60
192.168.65.63
192.168.65.64
37Given the network 192.168.25.0 shown in the graphic, which subnet mask would
accommodate the number of hosts in each subnet?
255.255.0.0
255.255.224.0
255.255.255.0
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
** 255.255.255.224
255.255.255.240
255.255.255.248
38 Which two protocols allow network devices to report their status and events to a
centralized network management device? (Choose two.)
** Syslog
Telnet
HTTP
HTTPS
** SNMP
PAT uses the word "overload" at the end of the access-list statement to share a single
registered address.
Static NAT allows an unregistered address to map to multiple registered addresses.
Dynamic NAT allows hosts to receive the same global address each time external
access is required.
**PAT uses unique source port numbers to distinguish between translations.
40Refer to the exhibit. The graphic shows the output of a command issued on router
RTB. According to the output, what two statements are true of router RTB? (Choose
two.)
41Refer to the exhibit. The network administrator uses the command below to
configure a default route to the ISP network :
RTB(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.6
A ping issued from the ISP is successful to router RTB. However, ping echo request
packets arrive at a host that is attached to the Fa0/0 interface of RTB, and the replies
do not make it back to the ISP router. What will fix this problem?
The ISP must be configured to forward packets from the 192.168.1.0 network.
**The ip route command needs to be edited so that the next hop address is 10.1.1.5.
The ip route command needs to be edited so that the 192.168.1.1 address is the next
hop address.
The ip route command should be removed from the RTB router configuration.
**SNMP
FTP
DHCP
SMTP
44A hacker attempts to reach confidential information that is stored on a server inside
the corporate network. A network security solution inspects the entire packet,
determines that it is a threat, and blocks the packet from entering the inside network.
Which security measure protected the network?
an IDS
**an IPS
a host-based firewall
Anti-X software
45 How many host addresses may be assigned on each subnetwork when using the
130.68.0.0 network address with a subnet mask of 255.255.248.0?
30
256
**2046
2048
4094
4096
46In an IPv4 environment, what information is used by the router to forward data
packets from one interface of a router to another?
Sonet
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
T3
**dialup
DSL
leased line
48The command copy tftp running-config has been entered on the router. What will
this command do?
49Refer to the exhibit. The network administrator needs to configure the Fa0/0
interface of RTB so that hosts from RTA can connect to the server that is attached to
RTB. Which two commands will the administrator use to accomplish this task?
(Choose two.)
50Refer to the exhibit. A NOC technician at an ISP enters the command shown. What
are two reasons to use this command? (Choose two.)