ASPHALT
BY
MOHAMMED IMTHIYAZ M.A
A road consists of a pavement and a surfacing. When combined, the surfacing and the
pavement are designed to carry the loads of heavy vehicles. The pavement provides the
structural stability for the road and consists of layers of crushed rock and stone of
selected sizes that is compacted using a limited amount of water as a binder. Figure 1
shows the typical layers in a pavement. These are (from top to bottom) are the base
course of typically crushed stone or gravel, the sub-base course of selected granular
material and the sub-grade which is the in-situ (native) soil. The material may be further
strengthened and stabilized with cement, lime or bitumen.3 Pavements in heavily
trafficked roads consist of asphalt or concrete instead of granular material in the base
and sub base layers.
Typically road surfacings are either Portland cement concrete or bitumen based. The
surfacing is to provide a running surface for cars and trucks and to provide a seal
against water infiltrating and harming the material in the pavement.
What is SMA?
Stone mastic asphalt was developed in Germany in the 1960’s; Stone Mastic asphalt
(SMA) provides a deformation resistant, durable, surfacing material, suitable for heavily
trafficked roads. SMA has found use in Europe, Australia and the United States as a
durable asphalt surfacing option for residential streets and highways. SMA has a high
coarse aggregate content that interlocks to form a stone skeleton that resist permanent
deformation. The stone skeleton is filled with a mastic of bitumen and filler to which
fibres are added to provide adequate stability of bitumen and to prevent drainage of
binder during transport and placement. Typical SMA composition consists of 70−80%
coarse aggregate, 8−12% filler, 6.0−7.0% binder, and 0.3 per cent fibre.
The deformation resistant capacity of SMA stems from a coarse stone skeleton providing
more stone-on-stone contact than with conventional dense graded asphalt (DGA) mixes
(see above picture). Improved binder durability is a result of higher bitumen content, a
thicker bitumen film and, lower air voids content. This high bitumen content also
improves of flexibility. Addition of a small quantity of cellulose or mineral fibre prevents
drainage of bitumen during transport and placement. There are no precise design
guidelines for SMA mixes. The essential features, which are the coarse aggregate
skeleton and mastic composition, and the consequent surface texture and mixture
stability, are largely determined by the selection of aggregate grading and the type and
proportion of filler and binder.
The bituminous mastic is intended to hold the aggregate in place and to inhibit the
ingress of moisture into the pavement and to provide durability. The mastic consists of
bitumen and fine aggregate particles; it may also include a polymer modified bitumen
and filler material to increase the mastic’s strength. Fibres may also be added to
stabilize the bitumen and to prevent the binder segregating from the aggregate during
transport and placement.
It is important that the aggregate material consist of only the larger stones (in the
structure) and fines to provide an effective mastic. The intermediate size aggregates are
not included, as these keep the larger aggregate apart and reduce the strength of the
SMA. See Figure 2.
Other surfacings include dense graded asphalts and open graded asphalts. These other
surfacings have a different aggregate grading given by the percentage of material that
will pass through sieves of given sizes, as shown in Figure 3.7 Table 1 presents the
same information and lists the typical proportions of aggregate or stone of a particular
size. This Table demonstrates the differences in the gradings for the different surfacings.
The dense graded asphalt has about equal proportions of aggregate in each of the four
sizes. Open graded asphalt (OGA) has a higher proportion of the larger stones
(compared with DGA) and a smaller percentage of small stones and fine particles
(material less than 1.18 mm). SMA typically has a higher proportion of the larger stones
and fine particles but relatively few stones of the intermediate sizes.
SMA also has more bitumen than other asphalts. It has about 6.5 per cent bitumen
compared to approximately 5 percent bitumen for DGA. The higher content of bitumen
increases its flexibility but can also create problems if it comes to the surface through the
compaction process. The bitumen acts as a lubricant and this can cause the aggregate
to separate from the mastic during aggressive compaction.
If an SMA mix is designed with too little bitumen, then the percentage of air voids will be
too great and water will infiltrate the surface and perhaps the underlying areas. Water in
the asphalt can also break the bond between the stones and the bitumen and allow the
bitumen to unravel.
The specifications, the mixing, the transport, the placement and compaction of SMA are
critical to achieving the desired result.
Manufacture
SMA is mixed and placed in the same plant as that used with conventional hot mix. In
batch plants, the fibre additive is added direct to the pugmill using individually wrapped
press packs or bulk dispensing equipment. Mixing times may be extended ensure that
fibre is homogeneously distributed throughout the mix and temperatures controlled in
order to avoid overheating or damage to the fibre. In drum plants, particular care must
be taken to ensure that both the additional filler content and fibre additive are
incorporated into the mixture without excessive losses through the dust extraction
system. Filler systems that add filler directly into the drum rather than aggregate feed are
preferred. Pelletised fibres may be added through systems designed for addition of
recycled materials, but a more effective means is addition through a special delivery line
that is combined with the bitumen delivery, so that the fibre is captured by bitumen at the
point of addition to the mixture.
Placement
The primary difference in placing SMA, compared to DGA is in compaction procedures.
Multi-tyred rollers are not used due to the possible working of binder-rich material to the
surface of the asphalt and consequent flushing and pick-up. Trafficking of the newly
placed asphalt while still warm may have the same effect and it is generally preferable
for surfaces to cool below about 40°C before opening to traffic. The preferred method of
compaction is to use heavy, non-vibrating, steel-wheeled rollers. If these are not
available, vibrating rollers may be used but vibration should be kept to a minimum to
avoid fracture of coarse aggregate particles, or drawing of binder to the surface of the
mix. The use of polymer modified binder may decreases mix workability and necessitate
increased compactive effort to achieve high standards of compacted density. Achieving
high standards of compacted density and low field air voids has been identified as an
important factor in the performance of all SMA work. SMA is normally placed with a
minimum layer thickness of 2.5 to 3 times the nominal maximum aggregate particle size.
Greater layer thicknesses assist in achieving appropriate standards of compacted
density.
Materials
Aggregates used in SMA must be of high quality – well shaped, resistant to crushing and
of suitable polish resistance.
During Aggregates and Road building’s Harnden & King were using their Barber-Greene
BG-260B 200 Series paver. SMA must be placed in a relatively narrow temperature
range of 145-155°C and at Martin Rd this meant material leaving the asphalt plant at a
maximum temperature of 165°C degrees.
Compaction was completed by two dual steel drum rollers; a10 tonne Dynapac CC42 for
breakdown, followed by a Ferguson 8 tonne roller. Both machines were doing four
passes and were achieving densities of about 90 per cent and 93 per cent.
SMA’s relatively rapid cooling rate means it must be compacted immediately after
placing, so the breakdown compactor makes each pass as close as possible to the
paver screed. SMA also has a sticky nature and compactor drums are lubricated with
liquid soap to ensure no pick up occurs.
At Brock Rd., the rolling pattern was adjusted by the addition of a second Dynapac
CC42 with each machine making four passes, followed by the Ferguson with three
passes. Overall production rates achieved were about 80 tonnes/ h at Martin Rd. and
110 tonnes /h at Brock Rd..
Advantages
• SMA provides a textured, durable, and rut resistant wearing course.
• The surface texture characteristics of SMA are similar to Open graded asphalt
(OGA) so that the noise generated by traffic is lower than that on DGA but equal
to or slightly higher than OGA.
• SMA can be produced and compacted with the same plant and equipment
available for normal hot mix, using the above procedure modifications.
• SMA may be used at intersections and other high traffic stress situations where
OGA is unsuitable.
• SMA surfacings may provide reduced reflection cracking from underlying cracked
pavements due to the flexible mastic.
• The durability of SMA should be equal, or greater than, DGA and significantly
greater than OGA.
Disadvantages
• Increased material cost associated with higher binder and filler contents, and
fibre additive.
• Increased mixing time and time taken to add extra filler, may result in reduced
productivity.
• Possible delays in opening to traffic as the SMA mix should be cooled to 40°C to
prevent flushing of the binder to the surface (bleeding).
• Initial skid resistance (lack of Friction) may be low until the thick binder film is
worn off the top of the surface by traffic. In critical situations, a small, clean grit,
may need to be applied before opening to traffic.
Where SMA should or should not be used?
SMA is not considered to be the only surfacing alternative and respondents considered
that the pavement selection guidelines should be consulted. Generally, SMA is ideal for
highways as its strength makes it more resistant to rutting. It is particularly useful when
there has been some cracking of a previous (lower) surfacing. SMA with its higher
bitumen content is a more flexible surfacing and this allows it to accommodate more
movement. As a result SMA decreases the tendency of cracking in the lower pavement
layers reflecting (or propagating) through and affecting the SMA surface. Other
surfacings like DGA do not have this capability. The ability to reduce cracking provides
for a longer pavement life. SMA is not suitable for small areas or for areas where the
asphalt laying plant has restricted access. SMA is very stiff and less workable than other
asphalts. This stiffness makes it harder to compact particularly if modified binders have
been used. The addition the use of modified binders decreases the time available for
compaction. Construction crews, plant and supervision must develop skills for the
effective placement and compaction of SMA. If these skills are not available
then SMA should not be used. Because SMA is difficult to compact by hand, it is not
suitable for small or restricted areas.
SMA is constructed with the significant stone on stone contact providing considerable
compressive strength. It is also constructed with a textured surface where the stones on
the upper surface stand proud of the mastic. This means that the stones are less
resistant to sideway (shear) forces on the surface caused by trucks making tight turns. In
these cases the tyre – surface forces can cause the “proud” stones to “roll out” and leave
the binder behind. SMA is often not recommended at smaller roundabouts and DGA
may be more appropriate. It is emphasized that any surfacing should not be considered
to be a “universal” solution for all conditions and local knowledge and experience should
be used to select the most appropriate mix.
SMA and OGA have been developed to provide an effective surface texture. This is a
prime safety requirement and helps to maintain skid resistance at the higher speeds.
The texture is also useful in decreasing the water depth on the surface. These qualities
make for safer roads. Skid resistance is a function of the micro texture (or the roughness
of the individual pieces of exposed aggregate) and the macro texture (developed from
the arrangement of the aggregate on the surface). These textures are shown
diagrammatically in Figure 4 from the Austroads “Guidelines for the Management of
Road Surface Skid Resistance”. Both qualities are required to produce effective skid
resistance at highway speeds.
• SMA has been, and is still, used by a number of authorities around Australia and
the world. Authorities are continuing to develop SMA as a durable asphalt with
large average texture depth.
• The average annual crash rate before SMA was installed was 40.6 crashes per
km for every 100 million vehicles; after the installation of SMA the annual crash
rate was virtually unchanged to 40.7 crashes per km for every 100 million
vehicles. This compared with an annual crash rate across the state of 44 crashes
per km for every 100 million vehicles. Motorists are less likely to crash on roads
surfaced with SMA than all other roads.
• The average annual fatal crash rate before SMA was installed was 0.77 fatal
crashes per km for every 100 million vehicles; after the installation of SMA the
annual fatal crash rate was less at 0.47 crashes per km for every 100 million
vehicles. This compared with an annual fatal crash rate across the state of 0.77
fatal crashes per km for every 100 million vehicles. Motorists are significantly less
likely to have a fatal crash on roads surfaced with SMA than all other roads.
Conclusions
• This report has addressed these major elements through interviews with a
number of respondents and through an investigation of all sites where the
Department of Main Roads used SMA.
• It is concluded that the process of introducing SMA into the Main Roads could
have been better. A number of recommendations are directed towards improving
procedures for introducing innovation in the Department of Main Roads.
• The use of SMA does not show any systemic safety issues. There are however
institutional issues that influence the effective use. Recommendations in this
report indicate how these issues can be addressed. A few sites where SMA has
been used should have the crash experience analyzed in more detail to
determine means of crash rate reductions.