89%(19)89% menganggap dokumen ini bermanfaat (19 suara)
11K tayangan2 halaman
This document summarizes the design of the base plate for column UC-203. It provides the design forces, material properties, dimensions of the column and base plate, and checks that:
1) The concrete bearing strength is sufficient to support the maximum compression force of 232.8 kN.
2) The required base plate thickness of 5.82 mm, based on an effective area calculation, is less than the actual thickness of 22 mm.
3) The stresses in the anchor bolts are less than their design strengths under the maximum tension and shear loads.
This document summarizes the design of the base plate for column UC-203. It provides the design forces, material properties, dimensions of the column and base plate, and checks that:
1) The concrete bearing strength is sufficient to support the maximum compression force of 232.8 kN.
2) The required base plate thickness of 5.82 mm, based on an effective area calculation, is less than the actual thickness of 22 mm.
3) The stresses in the anchor bolts are less than their design strengths under the maximum tension and shear loads.
This document summarizes the design of the base plate for column UC-203. It provides the design forces, material properties, dimensions of the column and base plate, and checks that:
1) The concrete bearing strength is sufficient to support the maximum compression force of 232.8 kN.
2) The required base plate thickness of 5.82 mm, based on an effective area calculation, is less than the actual thickness of 22 mm.
3) The stresses in the anchor bolts are less than their design strengths under the maximum tension and shear loads.
Column Mark : UC-203 UC203X203X46 1. DESIGN FORCES SUMMARY Fx Fy Fz Axial (F) (Fy 2 +Fz 2 ) 0.5 Friction (f) Shear Beam L/C NODE (kN) (kN) (kN) F = Fx (kN) Q (kN) f=0.45F (kN) Q - f (kN) 2027 456 255 232.8 30.2 3.3 232.8 30.4 104.8 0.0 2001 595 245 -13.9 10.5 0.0 -13.9 10.5 0.0 10.5 2030 595 256 -7.2 22.9 -0.5 -7.2 22.9 0.0 22.9 F = Fc (Axial Compression) if value is positive, F = Ft (Axial Tension) if values is negative 2. MATERIAL PROPERTY AND DIMENSION Steel Column : D = 203.2 mm B = 203.6 mm t = 7.2 mm T = 11.0 mm Base Plate : P yp = 265.0 Mpa (S275) D p = 250.0 mm B p = 250.0 mm tp = 22.0 mm Anchor Bolt : Grade : 4.6 db = 24.0 mm n = 2.0 pcs Effective Area per bolt (Ae perbolt ) = 353.0 mm 2 Effective Area of bolts (Ae bolts ) = 706.0 mm 2 3. CHECK FOR CONCRETE BEARING STRENGTH (4.13.1 of BS 5950-1:2000) f cu = 30.0 Mpa Fc / B p D p = 3.7 Mpa < 0.6fcu OK! 0.6f cu = 18.0 Mpa A req = Fc / 0.6F cu Fc = 232.8 kN (Maximum Compression Force) = 12,933.3 mm 2 4. CHECK FOR BASE PLATE THICKNESS BY EFFECTIVE AREA METHOD (sec 4.13.2.2 of BS 5950-1:2000) base plate thickness (tpreq) = c (3x0.6f cu /P yp ) 0.5 Column Perimeter (Per col ) = 1,190.0 mm effective area (Aeff) = 4c1 2 + c1(Per col ) + A col (Assuming no Overlap of Effective Area) Area of Steel Column A col = 5,870.0 mm 2 effective area (Aeff) = 4c2 2 + 2(D + B)c2 + DB (Assuming Effective Area has Overlap) solving for c by equating Aeff to Areq : 12,933.3 = 4c1 2 + 1,190.0c1 + 5,870.0 c1 = 5.82 mm 12,933.3 = 4c2 2 + 813.6c2 + 41,371.5 c2 = -44.84 mm (D-2T )/2 = 90.6 mm > c1, effective area has no overlap (use value of c1 for c) D +2c = 214.84 mm < Dp B + 2c = 215.24 mm < Bp Hence the calculated value of c is valid. c = 5.82 mm tp req = 2.7 mm < tp, OK! STAAD OUTPUT DESIGN FORCES UC-203 DESCRIPTION Condition Max Compression Max Tension Max Shear 4.4 BASE PLATE AND ANCHOR BOLT CHECK 5. ANCHOR BOLT STRESS CHECK 5.1 Design Strength of Anchor Bolts pt = 240 Mpa, tension strength of anchor bolt ps = 160 Mpa, shear strength of anchor bolt 5.2 Capacity of Ancor Bolts Tension Capacity of Anchor Bolts (Pt) = 162.8 kN Shear Capacity of Anchor Bolts (Ps) = 108.6 kN 5.3 Combined Tension and Shear Check Due to Maximum Tension, Load Case # : 595 Due to Maximum Shear, Load Case # : 595 Ft = 13.9 kN Ft = 7.2 kN V = 10.5 kN V = 22.9 kN Ft / Pt = 0.09 < 1.0 OK! Ft / Pt = 0.04 < 1.0 OK! V/Ps = 0.10 < 1.0 OK! V/Ps = 0.21 < 1.0, OK! (Ft/Pt) 2 + (V/Ps) 2 = 0.02 <1.0, OK! (Ft/Pt) 2 + (V/Ps) 2 = 0.05 <1.0, OK!