MEaG ! t £6 >
a
by
constructive s
Metode Kerja
Waterproofing coating
(Brushbond flex)
PT.FOSROC
Indonesia
Indonesia@fosrocco ideae
x
ar constructive solutions
By
BRUSHBOND FLEX
1. Pekerjaan Persiapan
Permukaan beton yang akan dipasang Brushbond flex, harus bersih dari oli, debu, dan
semua jenis kotoran yang mengganggu daya lekat. Beton yang gompal, atau
keropos harus diperbaiki terlebih dahulu dengan menggunakan bahan repair non-
shrink.
2. Peneampuran
* Tambahkan bahan bubuk secara perlahan - lahan kedalam bahan cairan
Brushbond flex dan aduk selama 2 - 4 menit dengan menggunakan mixer
sehingga bahan menjadi homogen.
* Jangan mengaduk material lebih banyak dari waktu pot life Brushbond flex (+ 30
- 40 menit).
Komponen Ratio Pencampuran
Brushbond
flex
Trowel Coating Spray
Bubuk 4 35 3
Liquid 1 1 1
3. Aplikasi
+ Buat kondisi permukaan beton lembab terlebih dahulu sebelum dicoating Brushbond
flex.
+ Aplikasikan Brushbond flex seperti mengecet dengan 1 x coating, lalu aplikasikan
lapisan kedua pada saat lapis pertama masih lembab.
Untuk setiap lapisan agar diberi tanda supaya pengecekan lapisan coating menjadi
mudah.
+ Untuk bidang yang luas,dianjurkan kembali metoda pelaksanaan dan batasan
(zone ) pengerjaan coating agar lebih memudahkan pengerjaan dan pengecekan
dilapanganTeETeLS
*
ar constructive solutions
L,
4. Curing
* Seperti bahan semen lainnya, produk inipun perlu dicuring untuk melindungi
material yang baru saja diaplikasikan ini dari sinar matahari langsung, dengan
menggunakan concure 75 dengan cara dikuaskan / diroll.
+ Lindungi dari hujan hingga material mengeras sempurna.
5. Proteksi
* Lindungi dengan screed 3 - 5 cm agar material tidak terkena sinar UV secara
langsung.
+ Maksimum waktu antara waterproofing Brushbond flex dengan screeding 24 jam.
+ Jika lebih dari 24 jam, sebaiknya dipasang bonding agent sebelum dipasang screed.Brushbond Flex
Gea
wT
a constructive solutions
Floxible Polymer-Cementitious Waterproofing
Membrane System
Brushbond Flex when fully cured, provides seamiess
‘exible waterpracting rrembrane for use in oot areas,
wet eroas, pre-cast joinis where 9 tough elastomeric
‘water light membrane is requires
Advantages.
18 Can be applied to weto: damp sunstrate
|& Simple application, no primer requred. Good
Adhesion te the concrete
| Flexible. Elastomenc propeties isl be able to bridge
cracks
1 Fast curng, wil alow for foot traffic when cured
1 Factory ofe-dlended two component system ensures
quality contol at ste
Description
Brushbond Flex is 2 two component palymer
madied cementitous coating which is supalied in
feady mix lz, When m0d, and eawy brushable
ccoaling is produced. t can simply be applied by a
itt brush, fll trowel to obtain the ested
thickness.
Brushbond Flex is specially formulated ftom selected
‘coment, grades hare-weanng aggregates end acsitwes
supplied in powder form togethar wit 3 quid
‘component of polymers providing exceptional adhesion
resivency, fexsoity tougnness and curabilty.
Physical Properties
Typical properties of Brushbond Flex are
Pot ito at 35°C 1 2hws
Mixes Dansiy «aim? 18
‘Adhesion to substrate >A Nine
Shore hardness at 256 240
‘at 2606, 7 days c
Elongation at Break (ASTM D12) > 50%
Tensile Strength (ASTM D412) > 1 Now
Floxtilty 25 mm Mandral Pass
Instruction for Use
Preparation
All he sutacos which are to eeenive Brushbond Flex
costing, must be ft ftom 08, grease, wax, dit oF any
other form of foreign matter which might affect adhesion
‘Spalled and doeply disintegrated concrete should ba
‘mod to sound concrete and repaired wih Renderoc
System.
‘The Brushbond Flex Liquids poured from the jeican.
container into the mixing vessel and mixed mechanically
tusing a slow speed dril mixer (350 ~ 450 rpm). Ade the
powder component gradually 10 the liquid to avoid lump
formation and mix for 4-§ mutes unti smooth
‘consistent max is achieved. Mix proportion (Laid
Ponwer} must be 1=2.by weight, Use the material within
the recommend pot ite.
Application
For best results, damp the surfaces before coating with
Brushbond Flex. Use a shor, stiff vse brush
preferably 120 12 200 mm in width, apply ike a paint
using one or two toats as required.
For trowe! application, ensure thal the substrate
levelled and repaired of any undulations or pot holes,
Brushbond Flex should be applied to the recommended
coverage is recommended for general re-suracing
‘hat each coat should be misimam t mm thickness and
an addition 2mm coating wil be eoquired for areas of
moderate to heavy pedestrian condilions,
Cleaning
Brushbond Flex should be removed from tooks and
equipment mmediately after use with ean water
Hardened material can orly be rermaved mechanically
Packaging,
Brushbond Flex is supplied 1 two component system
sn the folowing packaging
Powder 20 ka in plastic bag
Ligue 10 kg implastc jericanBrushbond Flex
The approximate coverage at 1.25 m2 per kg for single
coating, Recommended use s double coatings
application. Allowance should be made fer any possible
‘waste when estimates the consumption
Precautions
Health and Safety
Gloves and gaggles should be worn. Any splashes to
the skin or eyes should be washed off with clean water.
lin the event of prolonged iitalion, seek medical advice
Ponder product should be handled to minimise dust
formatian, use a light mask if excessive dust unavoidable,
fl
Stor
Brushbond Flex has a she’ lil of 12 months in unopened
ack, it is heptis a dry stor. In high humidity locations,
the seif Me may be ceduced 0 6-8 months.
Tehenical service
Fosros pravides a technical advisory service supported by a
1m of specialist inthe Fela
aA
PT. Fosroc
Indonesia
A Aas Bl AB No, #
Desi Soon rest ark
peo Ckarang
Important note
Sere her af catbor surg tos bveer et yvdei caw
telephone toe oni
22218977003, 62218972107 iroresa@fowce com
26222620 1308 262725222713
52315022711