Anda di halaman 1dari 138

Preface

Contents

SIPROTEC
Multifuction Protection
7SJ66
IEC61850
Mapping

C53000-L2640-C554-1

Basics

Mapping

Literature & Index

1
2

Disclaimer of Liability
We have checked the text of this manual against the hardware and
software described. However, deviations from the description cannot be completely ruled out, so that no liability can be accepted for
any errors or omissions contained in the information given.
The information given in this document is reviewed regularly and
any necessary corrections will be included in subsequent editions.
We appreciate any suggestions for improvement.
We reserve the right to make technical improvements without notice.

Copyright
Copyright Siemens AG 2014
Dissemination or reproduction of this document, or evaluation and
communication of its contents, is not authorized except where expressly permitted. Violations are liable for damages. All rights reserved, particularly for the purposes of patent application or
trademark registration.

Document Release V04.00.00


Edition 03.2014

Registered Trademarks
SIPROTEC, SINAUT, SICAM and DIGSI are registered trademarks
of Siemens AG. Other designations in this manual might be trademarks whose use by third parties for their own purposes would infringe the rights of the owner.

Siemens Aktiengesellschaft

Order No.: C53000-L2640-C554-1

Preface
Purpose of this manual
In this Manual, you will find the
General information about the effects of configuration of your device to the different Logical

Nodes and DOIs


Mapping of device relevant information to Logical Nodes as part of protocol IEC61850

Target audience
This manual is intended mainly for all persons who configure, parameterize and operate
SIPROTEC Devices 7SJ66
Scope of validity of this Manual
SIPROTEC 7SJ66, Versions from 4.00 and higher
Standards
This document has been created according to the ISO 9001 quality standards.
Further Support
If you have questions about SIPROTEC IEC 61850 interface, please contact your Siemens sales
representative.

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Table of contents

Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.1

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.2
1.2.1
1.2.2

Effects of Configuration on the Logical Nodes . . . . . . . . . . . . . . . . . . . . . . . . . . . .


Function parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Function parameters SIPROTEC 7SJ66 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10
10
11

1.3

Allocation of Logical Nodes to Logical Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16

1.4
1.4.1
1.4.2
1.4.3

Logical Node LLN0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


Logical Device PROT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Logical Devices MEAS, DR and EXT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Logical Device CTRL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20
20
22
23

1.5
1.5.1
1.5.2

DOI Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Logical Device PROT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Logical Devices MEAS, CTRL, DR and EXT. . . . . . . . . . . . . . . . . . . . . . . . . . .

25
25
26

Mapping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

27

2.1
2.1.1

Device (LPHD1, CALH1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


Error with a summary alarm and Alarm summary event . . . . . . . . . . . . . . . . . .

28
29

2.2

Oscillographic Fault Records (RDRE1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

32

2.3
2.3.1
2.3.2
2.3.3

Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2) . . . . . . . . . . . . . . . . . .


Overcurrent Protection 50, 51 PH (PTOC6, PTOC7, PTOC18, PTOC1) . . . . .
Overcurrent Protection 50N, 51N (PTOC8, PTOC9, PTOC2) . . . . . . . . . . . . . .
Overcurrent Protection 50N, 51N (PTRC2) . . . . . . . . . . . . . . . . . . . . . . . . . . . .

34
34
39
43

2.4
2.4.1
2.4.2
2.4.3

Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3) . . . . . . . . . . . . . . . .


Directional Overcurrent Protection 67 (PTOC10, PTOC11, PTOC19, PTOC3)
Directional Overcurrent Protection 67N (PTOC12, PTOC13, PTOC20, PTOC4)
Directional Overcurrent Protection 67N (PTRC3) . . . . . . . . . . . . . . . . . . . . . . .

46
46
52
57

2.5

Single-Phase Overcurrent Protection (PTOC16, PTOC17) . . . . . . . . . . . . . . . . . .

61

2.6
2.6.1
2.6.2
2.6.3
2.6.4

Voltage Protection 27, 59 (PTUVx, PTOVx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


Undervoltage Protection 27 (PTUV1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Undervoltage Protection 27 (PTUV2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overvoltage Protection 59 (PTOV1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overvoltage Protection 59 (PTOV2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

64
64
66
68
69

2.7

Negative Sequence Protection 46 (PTOC14, PTOC15, PTOC5) . . . . . . . . . . . . . .

70

2.8
2.8.1
2.8.2

Motor Protection (PMSS1, PMRI1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


Motor Starting Protection 48 (PMSS1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motor Restart Inhibit 66 (PMRI1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

74
74
76

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

2.9

Load Jam Protection (PMLJ1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

77

2.10
2.10.1
2.10.2
2.10.3
2.10.4
2.10.5
2.10.6
2.10.7
2.10.8

Frequency protection 81 O/U (PTUFx, PTOFx). . . . . . . . . . . . . . . . . . . . . . . . . . . .


Frequency protection 81-1 U (PTUF1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Frequency protection 81-2 U (PTUF2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Frequency protection 81-3 U (PTUF3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Frequency protection 81-4 U (PTUF4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Frequency protection 81-1 O (PTOF1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Frequency protection 81-2 O (PTOF2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Frequency protection 81-3 O (PTOF3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Frequency protection 81-4 O (PTOF4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

79
79
81
83
85
87
89
91
93

2.11

QV Protection 27/Q (PTUV9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

95

2.12

Thermal overload protection (PTTR1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

96

2.13
2.13.1
2.13.2
2.13.3

Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx) . . . . . . . . . . . . . . . . .


Ground Fault Protection 64 (PHIZ1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ground Fault Protection 50N(s) (PSDE1, PSDE2) . . . . . . . . . . . . . . . . . . . . . . .
51 N(s) (PSDE3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

98
98
103
106

2.14

Automatic Reclosing System 79 (RREC1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

108

2.15

Fault Locator (RFLO1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

110

2.16

Circuit breaker failure protection 50BF(RBRF1) . . . . . . . . . . . . . . . . . . . . . . . . . . . .

112

2.17

Synchronism and Voltage Check 25 (RSYNx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

114

2.18

Three-pole tripping 52 Breaker (XCBR1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

117

2.19

Tripping Logic of the Entire Device (PTRC1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

121

2.20
2.20.1
2.20.2
2.20.3

Measurement (MMXU1, MSQI1, MMTR1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


Measures (MMXU1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Measured values, symmetrical components (MSQI1) . . . . . . . . . . . . . . . . . . . .
Power Metering (MMTR1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

123
123
128
130

Literature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

133

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Basics

Basics

Contents
This chapter contains general information about the effects of device configuration on Logical
Nodes and DOIs.

1.1

General

1.2

Effects of Configuration on the Logical Nodes

10

1.3

Allocation of Logical Nodes to Logical Devices

16

1.4

Logical Node LLN0

20

1.5

DOI Behavior

25

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Basics
1.1 General

1.1

General

The protocol IEC 61850 was developed to define a standard that can be internationally
employed for the transmission of power automation system data.
This cross national standard enables an interoperability between automation systems and
devices made by different manufacturers.
7SJ66x can be equipped with an Ethernet module via which the protocol IEC 61850 is
interpreted.
The configuration of the protocol and the integration of the device with redundant IEC 61850
interfaces in your network are performed via the configuration system DIGSI.

Note
The following definitions are taken mainly from standard IEC 61850, Technical Specification
IEC TS 61850-2.

Logical Devices
LD Logical Devices represent a functional structuring of the LN Logical Nodes of a SIPROTEC
device.
The following Logical Devices are present:
Logical Device Protection PROT
Logical Device Measurement MEAS
Logical Device Disturbance Recorder DR
Logical Device Control CTRL
Logical Device Extended EXT

Each LD contains LN LLN0 and LN LPHD1.


The allocation of the Logical Nodes to the Logical Devices is listed in Chapter 1.3.

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Basics
1.1 General

Logical Node LN
Smallest part of a function that exchanges data. A logical node is an object defined by its data
and methods.
Data object instance DOI
A Data object is part of a logical node object representing specific information for example status
of measurement. From an object-oriented point of view, a data object is an instance of a data
class. Specific data classes carry the semantic within a logical node.
Data attribute instance DAI
A Data attribute defines the name (semantic), format, range of possible values, and
representation of values while being communicated.
Annunciation types via GOOSE
Generic Object Oriented Substation Event
A GOOSE report enables high speed trip signals to be issued with a high probability of delivery.
The following types of information can be configured via GOOSE.
External single point indication O/O
External single point indication I/O
External double point indication
External double point indication, fast
External operational measured values
External metered values

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Basics
1.2 Effects of Configuration on the Logical Nodes

1.2

Effects of Configuration on the Logical Nodes

1.2.1

Function parameters
Depending on the configuration of the function parameters the functions of the SIPROTEC are
enabled or disabled. If a function is disabled, the corresponding Logical Node is not available.

The following Logical Nodes are always available:

10

Logical Device Protection:

LLN0, LPHD1, XCBR1,


PTRC1

Logical Device Measurement:

LLN0, LPHD1, MMXU1,


MMTR1, MSQI1

Logical Device Control:

LLN0, LPHD1, CALH1

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Basics
1.2 Effects of Configuration on the Logical Nodes

1.2.2

Function parameters SIPROTEC 7SJ66


The following table shows which Logical Nodes are available when setting the corresponding
function parameter.
The setting (-) implies that no corresponding LN is available.

Table 1-1

SIPROTEC 7SJ66 - Effects of Function parameters to the Logical Nodes

No.

Function

103

Setting Group Change Option

104

Oscillographic Fault Records

112

113

50/51 (Charac. Phase)


Overcurrent Protection

50N/51N (Charac. Ground)


Overcurrent Protection

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Setting

Logical Nodes
No effect

Disabled

Enabled

RDRE1

Disabled

Definite Time

PTOC6, PTOC7, PTOC1


PTOC18, PTRC2

TOC IEC

PTOC6, PTOC7, PTOC1


PTOC18, PTRC2

TOC ANSI

PTOC6, PTOC7, PTOC1


PTOC18, PTRC2

User Defined PU

PTOC6, PTOC7, PTOC1


PTOC18, PTRC2

Userdef. Reset

PTOC6, PTOC7,
PTOC1, PTOC18,
PTRC2

Disabled

Definite Time

PTOC8, PTOC9,
PTOC2, PTRC2

TOC IEC

PTOC8, PTOC9,
PTOC2, PTRC2

TOC ANSI

PTOC8, PTOC9,
PTOC2, PTRC2

User Defined PU

PTOC8, PTOC9,
PTOC2, PTRC2

Userdef. Reset

PTOC8, PTOC9,
PTOC2, PTRC2

11

Basics
1.2 Effects of Configuration on the Logical Nodes

Table 1-1

SIPROTEC 7SJ66 - Effects of Function parameters to the Logical Nodes (Cont.)

No.

Function

Setting

Logical Nodes

115

67, 67-TOC
Directional Overcurrent Protection

Disabled

Definite Time

PTOC10, PTOC11,
PTOC19, PTOC3,
PTRC3

TOC IEC

PTOC10, PTOC11,
PTOC19, PTOC3,
PTRC3

TOC ANSI

PTOC10, PTOC11,
PTOC19, PTOC3,
PTRC3

User Defined PU

PTOC10, PTOC11,
PTOC19, PTOC3,
PTRC3

Userdef. Reset

PTOC10, PTOC11,
PTOC19, PTOC3,
PTRC3

Disabled

Definite Time

PTOC12, PTOC13,
PTOC20, PTOC4,
PTRC3

TOC IEC

PTOC12, PTOC13,
PTOC20, PTOC4,
PTRC3

TOC ANSI

PTOC12, PTOC13,
PTOC20, PTOC4,
PTRC3

User Defined PU

PTOC12, PTOC13,
PTOC20, PTOC4,
PTRC3

Userdef. Reset

PTOC12, PTOC13,
PTOC20, PTOC4,
PTRC3

116

67N, 67N-TOC
Directional Overcurrent Protection

117

Cold Load Pickup

No effect

122

2nd Harmonic Inrush Restraint

No effect

12

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Basics
1.2 Effects of Configuration on the Logical Nodes

Table 1-1

SIPROTEC 7SJ66 - Effects of Function parameters to the Logical Nodes (Cont.)

No.

Function

Setting

Logical Nodes

127

50 1Ph
Single Phase Overcurrent Protection

Disabled

Enabled

PTOC16, PTOC17

cos / sin

see Parameter 131

V0/I0 mea.

see Parameter 131

Disabled

Definite Time

PHIZ1, PSDE1, PSDE2

TOC IEC

PHIZ1, PSDE2, PSDE3

TOC IANSI

PHIZ1, PSDE2, PSDE3

User Defined PU

PHIZ1, PSDE2, PSDE3

Log. inverse 1

PHIZ1, PSDE2, PSDE3

Log. inverse 2

PHIZ1, PSDE2, PSDE3

Disabled

Definite Time

PHIZ1, PSDE1, PSDE2

User Defined PU

PHIZ1, PSDE1, PSDE2

130

131

131

(sens.) Ground fault dir. characteristic

(sensitive) Ground fault


and
(sens.) Ground fault dir. characteristic =
cos / sin

(sensitive) Ground fault


and
(sens.) Ground fault dir. characteristic =
V0/I0 mea.

133

Intermittent earth fault protection

No effect

134

Dir. Intermittent earth fault protection

No effect

140

46 Negative Sequence Protection

141

48 Startup Supervision of Motors

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Disabled

TOC ANSI

PTOC14, PTOC15,
PTOC5

TOC IEC

PTOC14, PTOC15,
PTOC5

Definite Time

PTOC14, PTOC15

Disabled

Enabled

PMSS1

13

Basics
1.2 Effects of Configuration on the Logical Nodes

Table 1-1

SIPROTEC 7SJ66 - Effects of Function parameters to the Logical Nodes (Cont.)

No.

Function

Setting

Logical Nodes

142

49 Thermal Overload Protection

Disabled

No ambient temp

PTTR1

With amb. temp.

PTTR1

Disabled

Enabled

PMRI1

Disabled

Enabled

PMLJ1

Disabled

Enabled

PTUV1, PTUV2,
PTOV1, PTOV2

Disabled

Enabled

PTOF1 PTOF4,
PTUF1 PTUF4

Disabled

Enabled

PTUV7

Disabled

SYNCHROCHECK

RSYN1

Disabled

Enabled

RBRF1

enabled w/ 3I0>

RBRF1

Disabled

Enabled

RREC1

143

144

150

154

155

161

170

171

66 Startup Counter for Motors

Load Jam Protection

27, 59 Under/Overvoltage Protection

81 Over/Underfrequency Protection

27/Q-Protection

25 Function group 1
Synchronism and Voltage Check

50BF Breaker Failure Protection

79 Auto-Reclose Function

172

52 Breaker Wear Monitoring

180

Fault Locator

181

14

Line sections for fault locator

No effect
Disabled

Enabled

RFLO1
No effect

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Basics
1.2 Effects of Configuration on the Logical Nodes

Table 1-1

SIPROTEC 7SJ66 - Effects of Function parameters to the Logical Nodes (Cont.)

No.

Function

Setting

Logical Nodes

182

74TC Trip Circuit Supervision

Disabled

2 Binary Inputs

DOI CirSpv, LN XCBR


LD PROT

1 Binary Input

DOI CirSpv, LN XCBR


LD PROT

190

External Temperature Input

No effect

191

Ext. Temperature Input Connection Type

No effect

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

15

Basics
1.3 Allocation of Logical Nodes to Logical Devices

1.3

Allocation of Logical Nodes to Logical Devices

All Logical Nodes (LN) are allocated to Logical Devices (LD). The following tables show this
allocation and the DOIs available for each LN.
LD PROT
The Logical Device PROT (Protection) contains the following LNs:
Table 1-2

LD PROT - Logical Nodes

LN

Function

DOI

LLN0

General

Mod, Beh, Health, NamPlt, OpTmh

PTRC1

General device pickup


General OFF

Mod, Beh, Health, NamPlt, Str,Tr,FinTr

XCBR1

52 Breaker
Three-pole tripping

Mod, Beh, Health, NamPlt, Loc, OpCnt, Pos


BlkOpn, BlkCls, CBOpCap
SumSwARs1, SumSwARs2, SumSwARs3

PTOC6
PTOC7
PTOC18
PTOC1
PTRC2

50/51 (Charac. Phase)

Mod, Beh, Health, NamPlt, Str, Op, ChgSet

PTOC8
PTOC9
PTOC2
PRTC2

50N/51N (Charac. Ground)

Mod, Beh, Health, NamPlt, Str, Op, ChgSet

PTOC10
PTOC11
PTOC19
PTOC3
PTRC3

67, 67-TOC

Mod, Beh, Health, NamPlt, Str, Op, ChgSet

PTOC12
PTOC13
PTOC20
PTOC4
PRTC3

67N, 67N-TOC

Mod, Beh, Health, NamPlt, Str, Op, ChgSet

PTOC16
PTOC17

50 1Ph

Mod, Beh, Health, NamPlt, Str, Op

PTUV1
PTUV2

27 Undervoltage Protection

Mod, Beh, Health, NamPlt, Str, Op

PTOV1
PTOV2

59 Overvoltage Protection

Mod, Beh, Health, NamPlt, Str, Op

16

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Basics
1.3 Allocation of Logical Nodes to Logical Devices

Table 1-2

LD PROT - Logical Nodes (Cont.)

LN

Function

DOI

PTUV7

27/Q-Protection

Mod, Beh, Health, NamPlt, Str, Op

PTOC14
PTOC15
PTOC5

46 Negative Sequence Protection

Mod, Beh, Health, NamPlt, Str, Op

PMSS1

48 Startup Supervision of Motors

Mod, Beh, Health, NamPlt, Str, Op

PMRI1

66 Startup Counter for Motors

Mod, Beh, Health, NamPlt, Op, StrInhTmm

PMLJ1

Load Jam Protection

Mod, Beh, Health, NamPlt, Str, Op, LDJamAlm,


ChgSet

PTUF1
PTUF2
PTUF3
PTUF4

81 Underfrequency Protection

Mod, Beh, Health, NamPlt, Str, Op, BlkV

PTOF1
PTOF2
PTOF3
PTOF4

81 Overfrequency Protection

Mod, Beh, Health, NamPlt, Str, Op, BlkV

PTTR1

49 Thermal Overload Protection

Mod, Beh, Health, NamPlt, Str, Op, AlmThm

PSDE1
PSDE2
PSDE3

(sensitive) Ground fault

Mod, Beh, Health, NamPlt, Str, Op

PHIZ1

(sensitive) Ground fault

Mod, Beh, Health, NamPlt, Str, Op

RREC1

79 Auto-Reclose Function

Mod, Beh, Health, NamPlt, Op, AutoRecSt

RFLO1

Fault Locator

Mod, Beh, Health, NamPlt, FltZ, FltDiskm, FltDisPrc

RBRF1

50BF Breaker Failure Protection

Mod, Beh, Health, NamPlt, Str, OpEx, OpIn

LPHD1

Device

PhyNam, PhyHealth, Proxy

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

17

Basics
1.3 Allocation of Logical Nodes to Logical Devices

LD MEAS
The Logical Device MEAS (Measurement) contains the following LNs:
Table 1-3

LD MEAS - Logical Nodes

LN

Function

DOIs

LLN0

General

Mod, Beh, Health, NamPlt

MMXU1

Operational measured values

Mod, Beh, Health, NamPlt,


TotW, TotVAr, TotVA, TotPF, Hz, PPV, PhV, A

MMTR1

Power Metering

Mod, Beh, Health, NamPlt,


SupWh, SupVArh, DmdWh, DmdVArh

MSQI1

Measured values, symmetrical


components

Mod, Beh, Health, NamPlt, SeqA, SeqV

LPHD1

Device

PhyNam, PhyHealth, Proxy

LD DR
The Logical Device DR (Disturbance Recorder) contains the following LNs:
Table 1-4

LD DR - Logical Nodes

LN

Function

DOIs

LLN0

General

Mod, Beh, Health, NamPlt

RDRE1

Oscillographic Fault Records

Mod, Beh, Health, NamPlt, RcdMade, RcdStr


FltNum, GriFltNum

LPHD1

Device

PhyNam, PhyHealth, Proxy

18

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Basics
1.3 Allocation of Logical Nodes to Logical Devices

LD CTRL
The Logical Device CTRL (Control) contains the following LNs:
Table 1-5

LD CTRL - Logical Nodes

LN

Function

DOIs

LLN0

General

Mod, Beh, Health, NamPlt, LEDRs, Loc

RSYN1

25 Function group 1

Mod, Beh, Health, NamPlt,


Rel, VInd, AngInd, HzInd, SynPrg,
DifVClc, DifHzClc, DifAngClc

CALH1

Error with a summary alarm and


Alarm summary event

Mod, Beh, Health, NamPlt, GrAlm, GrWrn,


ErrBoard1, ErrBoard2, ErrBoard3, ErrBoard4,
ErrBoard5, ErrBoard6, ErrBoard7

LPHD1

Device

PhyNam, PhyHealth, Proxy, CtlNum, DevStr

LD EXT
The Logical Device EXT (Extended) contains the following LNs:
Table 1-6

LD EXT - Logical Nodes

LN

Function

DOIs

LLN0

General

Mod, Beh, Health, NamPlt, LEDRs, Loc

LPHD1

Device

PhyNam, PhyHealth, Proxy, CtlNum

The Logical Nodes of the switching (and userdefined) objects will be created by DIGSI during
the parameterization of your SIPROTEC device.
MICS, Model Implementation Conformance Statement, shows the assignment of the DOIs;
you can use DIGSI to print the MICS.

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

19

Basics
1.4 Logical Node LLN0

1.4

Logical Node LLN0

1.4.1

Logical Device PROT

LLN0.Mod
No.

Information

51

Device is Operational and Protecting (Device OK)

0 1 1 1 1

Test mode (Test mode)

x 0 0 1 1

Stop data transmission (DataStop)

x 0 1 0 1

LLN0.Mod.stVal
device annunciation / setting:

5 1 2 3 4
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

LLN0.Beh
No.

Information

51

Device is Operational and Protecting (Device OK)

0 1 1 1 1

Test mode (Test mode)

x 0 0 1 1

Stop data transmission (DataStop)

x 0 1 0 1

LLN0.Beh.stVal
device annunciation / setting:

5 1 2 3 4
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Beh.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

LLN0.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

LLN0.Health.stVal
device annunciation:

20

0 1
3 1

1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Basics
1.4 Logical Node LLN0

LLN0.OpTmh
No.
1020

Information
Counter of operating hours (Op.Hours=)

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Value
LLN0.OpTmh.stVal

Operating hours (Absolute value)

21

Basics
1.4 Logical Node LLN0

1.4.2

Logical Devices MEAS, DR and EXT

LLN0.Mod
No.

Information

51

Device is Operational and Protecting (Device OK)

0 1 1 1 1

Test mode (Test mode)

x 1 1 0 0

Stop data transmission (DataStop)

x 1 0 1 0

LLN0.Mod.stVal
device annunciation / setting:

5 4 3 2 1
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

LLN0.Beh
No.

Information

51

Device is Operational and Protecting (Device OK)

0 1 1 1 1

Test mode (Test mode)

x 0 0 1 1

Stop data transmission (DataStop)

x 0 1 0 1

LLN0.Beh.stVal
device annunciation / setting:

5 1 2 3 4
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Beh.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

LLN0.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

LLN0.Health.stVal
device annunciation:

22

0 1
3 1

1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Basics
1.4 Logical Node LLN0

1.4.3

Logical Device CTRL

LLN0.Mod
No.

Information

55

Reset Device (Reset Device)

1 1 1 1 1

51

Device is Operational and Protecting (Device OK)

1 1 1 1 0

Test mode (Test mode)

1 1 0 0 0

Stop data transmission (DataStop)

1 0 1 0 0

LLN0.Mod.stVal
device annunciation / setting:

4 3 2 1 5
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

LLN0.Beh
No.

Information

55

Reset Device (Reset Device)

1 1 1 1 1

51

Device is Operational and Protecting (Device OK)

1 1 1 1 0

Test mode (Test mode)

1 1 0 0 0

Stop data transmission (DataStop)

1 0 1 0 0

LLN0.Beh.stVal
device annunciation / setting:

4 3 2 1 5
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Beh.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

LLN0.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

LLN0.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

23

Basics
1.4 Logical Node LLN0

LLN0.OpTmh
No.
1020

24

Information
Counter of operating hours (Op.Hours=)

Value
LLN0.OpTmh.stVal

Operating hours (Absolute value)

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Basics
1.5 DOI Behavior

1.5

DOI Behavior

1.5.1

Logical Device PROT


For the Logical Nodes of the PROT Logical Device, LNx.Beh.stVal is formed from
LNx.Mod.stVal of the Logical Node and the status of the following device messages:
Test mode (Test mode),
Stop data transmission and

At Least 1 Protection Funct. is Active.


No.

51

Information
Test mode (Test mode)

x 0 1 0 1 x

Stop data transmission (DataStop)

x 0 0 1 1 x

Device is Operational and Protecting (Device OK)

x 1 1 1 1 0

LNx .Mod.stVal

5 1 1 1 1 x
5 1 3 2 4 5

LNx.Beh.stVal
device annunciation / setting:

1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

25

Basics
1.5 DOI Behavior

1.5.2

Logical Devices MEAS, CTRL, DR and EXT


For the Logical Nodes of the MEAS, CTRL, DR and EXT Logical Devices, LNx.Beh.stVal is
formed from LNx.Mod.stVal of the Logical Node and the status of the following device
messages:
Test mode (Test mode),
Stop data transmission.

No.

Information
Test mode (Test mode)

x 0 1 0 1 0 1

Stop data transmission (DataStop)

x 0 0 1 1 x x

LNx .Mod.stVal

5 1 1 1 1 2 2
5 1 3 2 4 2 4

LNx.Beh.stVal
device annunciation / setting:

26

1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping

Mapping

Contents
This chapter shows the mapping of the information relevant to the device on the Logical Node of
protocol IEC61850. It is structured according to function. In Chapter 1 you can find what
consequences non-configured functions have on the Logical Nodes as well as general
information about IEC 61850 mapping of information.

2.1

Device (LPHD1, CALH1)

28

2.2

Oscillographic Fault Records (RDRE1)

32

2.3

Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

34

2.4

Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

46

2.5

Single-Phase Overcurrent Protection (PTOC16, PTOC17)

61

2.6

Voltage Protection 27, 59 (PTUVx, PTOVx)

64

2.7

Negative Sequence Protection 46 (PTOC14, PTOC15, PTOC5)

70

2.8

Motor Protection (PMSS1, PMRI1)

74

2.9

Load Jam Protection (PMLJ1)

77

2.10

Frequency protection 81 O/U (PTUFx, PTOFx)

79

2.11

QV Protection 27/Q (PTUV9)

95

2.12

Thermal overload protection (PTTR1)

96

2.13

Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)

98

2.14

Automatic Reclosing System 79 (RREC1)

108

2.15

Fault Locator (RFLO1)

110

2.16

Circuit breaker failure protection 50BF(RBRF1)

112

2.17

Synchronism and Voltage Check 25 (RSYNx)

114

2.18

Three-pole tripping 52 Breaker (XCBR1)

117

2.19

Tripping Logic of the Entire Device (PTRC1)

121

2.20

Measurement (MMXU1, MSQI1, MMTR1)

123

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

27

Mapping
2.1 Device (LPHD1, CALH1)

2.1

Device (LPHD1, CALH1)

LPHD1.DevStr
No.

Information

56

Initial Start of Device (Initial Start)

0 0 1 1

67

Resume (Resume)

0 1 0 1

LPHD1.DevStr.stVal
device annunciation:

1 - ON
0 - OFF

T 2 1 T
IEC Status DevStr.stVal:

1 - Initial Start
2 - Resume
T - toggel between 1 and 2

LPHD1.Proxy
No.
55

Information
Reset Device (Reset Device)

LPHD1.Proxy.stVal
device annunciation:

0 1
1 0

1 - ON
0 - OFF

IEC Status Proxy.stVal:

0 - DEVICE is not a PROXY


1 - DEVICE is a PROXY

LPHD1.PhyHealth
No.
51

Information
Device is Operational and Protecting (Device OK)

LPHD1.PhyHealth.stVal
device annunciation:

28

1 - ON
0 - OFF

0 1
3 1

IEC Status PhyHealth.stVal:

1 - OK
2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.1 Device (LPHD1, CALH1)

2.1.1

Error with a summary alarm and Alarm summary event

CALH1.Mod
No.
56

Information
Initial Start of Device (Initial Start)

CALH1.Mod.stVal
device annunciation:

1 0
1 5

1 - ON
0 - OFF

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

CALH1.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

CALH1.Health.stVal
device annunciation:

1 - ON
0 - OFF

0 1
3 1

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

CALH1.GrAlm
No.
140

Information
Error with a summary alarm (Error Sum Alarm)

CALH1.GrAlm.stVal
device annunciation:

1 - ON
0 - OFF

1 0
1 0

IEC Status GrAlm.stVal:

0 - FALSE
1 - TRUE

CALH1.GrWrn
No.
160

Information
Alarm Summary Event (Alarm Sum Event)

CALH1.GrWrn.stVal
device annunciation:

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

1 0
1 0

IEC Status GrWrn.stVal:

0 - FALSE
1 - TRUE

29

Mapping
2.1 Device (LPHD1, CALH1)

The LN CALH1.ErrBoard1 to CALH1.ErrBoard7 are available with Firmware


CALH1.ErrBoard1
No.
183

Information
Error Board 1 (Error Board 1)

CALH1.ErrBoard1.stVal
device annunciation:

1 - ON
0 - OFF

1 0
1 0

IEC Status ErrBoard1.stVal:

0 - FALSE
1 - TRUE

CALH1.ErrBoard2
No.
184

Information
Error Board 2 (Error Board 2)

CALH1.ErrBoard2.stVal
device annunciation:

1 - ON
0 - OFF

1 0
1 0

IEC Status ErrBoard2.stVal:

0 - FALSE
1 - TRUE

CALH1.ErrBoard3
No.
185

Information
Error Board 3 (Error Board 3)

CALH1.ErrBoard3.stVal
device annunciation:

1 - ON
0 - OFF

1 0
1 0

IEC Status ErrBoard3.stVal:

0 - FALSE
1 - TRUE

CALH1.ErrBoard4
No.
186

Information
Error Board 4 (Error Board 4)

CALH1.ErrBoard4.stVal
device annunciation:

30

1 - ON
0 - OFF

1 0
1 0

IEC Status ErrBoard4.stVal:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.1 Device (LPHD1, CALH1)

CALH1.ErrBoard5
No.
187

Information
Error Board 5 (Error Board 5)

CALH1.ErrBoard5.stVal
device annunciation:

1 - ON
0 - OFF

1 0
1 0

IEC Status ErrBoard5.stVal:

0 - FALSE
1 - TRUE

CALH1.ErrBoard6
No.
188

Information
Error Board 6 (Error Board 6)

CALH1.ErrBoard6.stVal
device annunciation:

1 - ON
0 - OFF

1 0
1 0

IEC Status ErrBoard6.stVal:

0 - FALSE
1 - TRUE

CALH1.ErrBoard7
No.
189

Information
Error Board 7 (Error Board 7)

CALH1.ErrBoard7.stVal
device annunciation:

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

1 0
1 0

IEC Status ErrBoard7.stVal:

0 - FALSE
1 - TRUE

31

Mapping
2.2 Oscillographic Fault Records (RDRE1)

2.2

Oscillographic Fault Records (RDRE1)

RDRE1.Mod
No.
55

Information
Reset Device (Reset Device)

RDRE1.Mod.stVal
device annunciation:

x
1

1 - ON
0 - OFF
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

RDRE1.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

RDRE1.Health.stVal
device annunciation:

1 - ON
0 - OFF

0 1
3 1

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

RDRE1.RcdMade
No.
30053

Information
Fault recording is running (Fault rec. run.)

RDRE1.RcdMade.stVal
device annunciation:

32

1 - ON
0 - OFF

0 1
1 0

IEC Status RcdMade.stVal:

0 - FALSE
1 - TRUE
(Recording complete)

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.2 Oscillographic Fault Records (RDRE1)

RDRE1.FltNum
No.
302

Information

Value

Fault Event (Fault Event)

RDRE1.FltNum.stVal

Present fault number

RDRE1.GriFltNum
No.
301

Information

Value

Power System fault (Pow.Sys.Flt.)

RDRE1.GriFltNum.stVal

Network fault number

RDRE1.RcdStr
No.
30053

Information
Fault recording is running (Fault rec. run.)

RDRE1.RcdStr.stVal
device annunciation:

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

0 1
0 1

IEC Status RcdStr.stVal:

0 - FALSE
1 - TRUE

33

Mapping
2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

2.3

Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

2.3.1

Overcurrent Protection 50, 51 PH (PTOC6, PTOC7, PTOC18, PTOC1)

PTOC6.Mod
No.
1751

Information
50/51 O/C switched OFF (50/51 PH OFF)

1 x 0

50-1 PICKUP (P1204) =

x 1 0

PTOC6.Mod.stVal

5 5 1

device annunciation / setting:

1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC6.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOC6.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PTOC6.Str
No.

Information

1810

50-1 picked up (50-1 picked up)

PTOC6.Str.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTOC6.Op
No.
1815

Information
50-1 TRIP (50-1 TRIP)

0 1

PTOC6.Op.general
device annunciation:

34

0 1
1 - ON
0 - OFF

IEC Status Op.general:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

PTOC6.ChgSet
No.
1997

Information
Dynamic settings are ACTIVE (Dyn set. ACTIVE)

PTOC6.ChgSet.stVal
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status ChgSet.stVal:

0 - FALSE
1 - TRUE

PTOC7.Mod
No.
1751

Information
50/51 O/C switched OFF (50/51 PH OFF)

1 x 0

50-2 PICKUP (P1202) =

x 1 0

PTOC7.Mod.stVal

5 5 1

device annunciation / setting:

1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC7.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOC7.Health.stVal
device annunciation:

1 - ON
0 - OFF

0 1
3 1

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PTOC7.Str
No.

Information

1800

50-2 picked up (50-2 picked up)

PTOC7.Str.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Str.general:

0 - FALSE
1 - TRUE

35

Mapping
2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

PTOC7.Op
No.
1805

Information
50-2 TRIP (50-2 TRIP)

0 1

PTOC7.Op.general
device annunciation:

0 1
1 - ON
0 - OFF

IEC Status Op.general:

0 - FALSE
1 - TRUE

PTOC7.ChgSet
No.
1997

Information
Dynamic settings are ACTIVE (Dyn set. ACTIVE)

PTOC7.ChgSet.stVal
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status ChgSet.stVal:

0 - FALSE
1 - TRUE

PTOC18.Mod
No.
1751

Information
50/51 O/C switched OFF (50/51 PH OFF)

1 x 0

50-3 PICKUP(P1217) =

x 1 0

PTOC18.Mod.stVal

5 5 1

device annunciation / setting:

1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC18.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOC18.Health.stVal
device annunciation:

36

1 - ON
0 - OFF

0 1
3 1

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

PTOC18.Str
No.

Information

1767

50-3 picked up (50-3 picked up)

PTOC18.Str.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTOC18.Op
No.
1769

Information
50-3 TRIP (50-3 TRIP)

0 1

PTOC18.Op.general
device annunciation:

0 1

1 - ON
0 - OFF

IEC Status Op.general:

0 - FALSE
1 - TRUE

PTOC18.ChgSet
No.
1997

Information
Dynamic settings are ACTIVE (Dyn set. ACTIVE)

PTOC18.ChgSet.stVal
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status ChgSet.stVal:

0 - FALSE
1 - TRUE

PTOC1.Mod
No.
1751

Information
50/51 O/C switched OFF (50/51 PH OFF)

PTOC1.Mod.stVal
device annunciation / setting:

1 0
5 1

1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

37

Mapping
2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

PTOC1.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOC1.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PTOC1.Str
No.
1820

Information
51 picked up (51 picked up)

PTOC1.Str.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTOC1.Op
No.
1825

Information
51 TRIP (51 TRIP)

0 1

PTOC1.Op.general
device annunciation:

0 1
1 - ON
0 - OFF

IEC Status Op.general:

0 - FALSE
1 - TRUE

PTOC1.ChgSet
No.
1997

Information
Dynamic settings are ACTIVE (Dyn set. ACTIVE)

PTOC1.ChgSet.stVal
device annunciation:

38

1 - ON
0 - OFF

0 1
0 1

IEC Status ChgSet.stVal:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

2.3.2

Overcurrent Protection 50N, 51N (PTOC8, PTOC9, PTOC2)

PTOC8.Mod
No.
7156

Information
50N/51N is OFF (50N/51N OFF)

1 x 0

50N-1 PICKUP (P1304) =

x 1 0

PTOC8.Mod.stVal

5 5 1

device annunciation / setting:

1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC8.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOC8.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PTOC8.Str
No.
1834

Information
50N-1 picked up (50N-1 picked up)

PTOC8.Str.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTOC8.Op
No.
1836

Information
50N-1 TRIP (50N-1 TRIP)

0 1

PTOC8.Op.general
device annunciation:

0 1
1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Op.general:

0 - FALSE
1 - TRUE

39

Mapping
2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

PTOC8.ChgSet
No.
1997

Information
Dynamic settings are ACTIVE (Dyn set. ACTIVE)

PTOC8.ChgSet.stVal
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status ChgSet.stVal:

0 - FALSE
1 - TRUE

PTOC9.Mod
No.
7156

Information
50N/51N is OFF (50N/51N OFF)

1 x 0

50N-2 PICKUP (P1302) =

x 1 0

PTOC9.Mod.stVal

5 5 1

device annunciation / setting:

1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC9.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOC9.Health.stVal
device annunciation:

1 - ON
0 - OFF

0 1
3 1

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PTOC9.Str
No.
1831

Information
50N-2 picked up (50N-2 picked up)

PTOC9.Str.general
device annunciation:

40

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

PTOC9.Op
No.
1833

Information
50N-2 TRIP (50N-2 TRIP)

0 1

PTOC9.Op.general
device annunciation:

0 1
1 - ON
0 - OFF

IEC Status Op.general:

0 - FALSE
1 - TRUE

PTOC9.ChgSet
No.
1997

Information
Dynamic settings are ACTIVE (Dyn set. ACTIVE)

PTOC9.ChgSet.stVal
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status ChgSet.stVal:

0 - FALSE
1 - TRUE

PTOC2.Mod
No.
1756

Information
50N/51N is OFF (50N/51N OFF)

PTOC2.Mod.stVal

1 0
5 1

device annunciation / setting:

1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC2.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOC2.Health.stVal
device annunciation:

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

0 1
3 1

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

41

Mapping
2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

PTOC2.Str
No.
1837

Information
51N picked up (51N picked up)

PTOC2.Str.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTOC2.Op
No.
1839

Information
51N TRIP (51N TRIP)

0 1

PTOC2.Op.general
device annunciation:

0 1
1 - ON
0 - OFF

IEC Status Op.general:

0 - FALSE
1 - TRUE

PTOC2.ChgSet
No.
1997

Information
Dynamic settings are ACTIVE (Dyn set. ACTIVE)

PTOC2.ChgSet.stVal
device annunciation:

42

1 - ON
0 - OFF

0 1
0 1

IEC Status ChgSet.stVal:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

2.3.3

Overcurrent Protection 50N, 51N (PTRC2)

PTRC2.Mod
No.
1751
1756

Information
50/51 O/C switched OFF (50/51 PH OFF) and
50N/51N is OFF (50N/51N OFF)

1 0

PTRC2.Mod.stVal
device annunciation / setting:

5 1
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTRC2.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTRC2.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PTRC2.Str
No.
1761

Information
50(N)/51(N) O/C PICKUP (50(N)/51(N) PU)

PTRC2.Str.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTRC2.Str.dirGeneral
No.

Information

PTRC2.Str.dirGeneral
device annunciation:

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

0
IEC Status Str.dirGeneral:

0 - UNKNOWN

43

Mapping
2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

PTRC2.Str.phsA
No.
1762

Information
50/51 Phase A picked up (50/51 Ph A PU)

PTRC2.Str.phsA
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.phsA:

0 - FALSE
1 - TRUE

PTRC2.Str.dirPhsA
No.

Information

PTRC2.Str.dirPhsA

device annunciation:

IEC Status Str.dirPhsA:

0 - UNKNOWN

PTRC2.Str.phsB
No.
1763

Information
50/51 Phase B picked up (50/51 Ph B PU)

PTRC2.Str.phsB
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.phsB:

0 - FALSE
1 - TRUE

PTRC2.Str.dirPhsB
No.

Information

PTRC2.Str.dirPhsB

device annunciation:

IEC Status Str.dirPhsB:

0 - UNKNOWN

PTRC2.Str.phsC
No.
1764

Information
50/51 Phase C picked up (50/51 Ph C PU)

PTRC2.Str.phsC
device annunciation:

44

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.phsC:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

PTRC2.Str.dirPhsC
No.

Information

PTRC2.Str.dirPhsC

device annunciation:

IEC Status Str.dirPhsC:

0 - UNKNOWN

PTRC2.Str.neut
No.
1765

Information
50N/51N picked up (50N/51NPickedup)

PTRC2.Str.neut
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.neut:

0 - FALSE
1 - TRUE

PTRC2.Str.dirNeut
No.

Information

PTRC2.Str.dirNeut

device annunciation:

IEC Status Str.dirPhsC:

0 - UNKNOWN

PTRC2.Op
No.
1791

Information
50(N)/51(N) TRIP (50(N)/51(N)TRIP)

PTRC2.Op.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Op.general:

0 - FALSE
1 - TRUE

45

Mapping
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

2.4

Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

2.4.1

Directional Overcurrent Protection 67 (PTOC10, PTOC11, PTOC19,


PTOC3)

PTOC10.Mod
No.
2651

Information
67/67-TOC switched OFF (67/67-TOC OFF)

1 x 0

67-1 PICKUP (P1504) =

x 1 0

PTOC10.Mod.stVal

5 5 1

device annunciation / setting:

1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC10.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOC10.Health.stVal
device annunciation:

1 - ON
0 - OFF

0 1
3 1

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PTOC10.Str
No.

Information

2660

67-1 picked up (67-1 picked up)

PTOC10.Str.general
device annunciation:

46

1 - ON
0 - OFF

0 1
0 1

IEC Status Str.general:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTOC10.Op
No.
2665

Information
67-1 TRIP (67-1 TRIP)

0 1

PTOC10.Op.general
device annunciation:

0 1

1 - ON
0 - OFF

IEC Status Op.general:

0 - FALSE
1 - TRUE

PTOC10.ChgSet
No.
1997

Information
Dynamic settings are ACTIVE (Dyn set. ACTIVE)

PTOC10.ChgSet.stVal
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status ChgSet.stVal:

0 - FALSE
1 - TRUE

PTOC11.Mod
No.
2651

Information
67/67-TOC switched OFF (67/67-TOC OFF)

1 x 0

67-2 PICKUP (P1502) =

x 1 0

PTOC11.Mod.stVal

5 5 1

device annunciation / setting:

1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC11.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOC11.Health.stVal
device annunciation:

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

0 1
3 1

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

47

Mapping
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTOC11.Str
No.

Information

2642

67-2 picked up (67-2 picked up)

PTOC11.Str.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTOC11.Op
No.
2649

Information
67-2 TRIP (67-2 TRIP)

0 1

PTOC11.Op.general
device annunciation:

0 1

1 - ON
0 - OFF

IEC Status Op.general:

0 - FALSE
1 - TRUE

PTOC11.ChgSet
No.
1997

Information
Dynamic settings are ACTIVE (Dyn set. ACTIVE)

PTOC11.ChgSet.stVal
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status ChgSet.stVal:

0 - FALSE
1 - TRUE

PTOC19.Mod
No.
2651

Information
67/67-TOC switched OFF (67/67-TOC OFF)

1 x 0

67-3 PICKUP (P1528) =

x 1 0

PTOC19.Mod.stVal
device annunciation / setting:

48

5 5 1
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTOC19.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOC19.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PTOC19.Str
No.

Information

2697

67-3 picked up (67-3 picked up)

PTOC19.Str.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTOC19.Op
No.
2678

Information
67-3 TRIP (67-3 TRIP)

0 1

PTOC19.Op.general
device annunciation:

1 - ON
0 - OFF

0 1
IEC Status Op.general:

0 - FALSE
1 - TRUE

PTOC19.ChgSet
No.
1997

Information
Dynamic settings are ACTIVE (Dyn set. ACTIVE)

PTOC19.ChgSet.stVal
device annunciation:

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

0 1
0 1

IEC Status ChgSet.stVal:

0 - FALSE
1 - TRUE

49

Mapping
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTOC3.Mod
No.
2651

Information
67/67-TOC switched OFF (67/67-TOC OFF)

PTOC3.Mod.stVal

1 0
5 1

device annunciation / setting:

1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC3.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOC3.Health.stVal
device annunciation:

1 - ON
0 - OFF

0 1
3 1

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PTOC3.Str
No.
2670

Information
67-TOC picked up (67-TOC picked up)

PTOC3.Str.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTOC3.Op
No.
2675

Information
67-TOC TRIP (67-TOC TRIP)

PTOC3.Op.general
device annunciation:

50

0 1
0 1

1 - ON
0 - OFF

IEC Status Op.general:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTOC3.ChgSet
No.
1997

Information
Dynamic settings are ACTIVE (Dyn set. ACTIVE)

PTOC3.ChgSet.stVal
device annunciation:

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

0 1
0 1

IEC Status ChgSet.stVal:

0 - FALSE
1 - TRUE

51

Mapping
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

2.4.2

Directional Overcurrent Protection 67N (PTOC12, PTOC13,


PTOC20, PTOC4)

PTOC12.Mod
No.
2656

Information
67N/67N-TOC switched OFF (67N OFF)

1 x 0

67N-1 PICKUP (P1604) =

x 1 0

PTOC12.Mod.stVal

5 5 1

device annunciation / setting:

1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC12.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOC12.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PTOC12.Str
No.
2681

Information
67N-1 picked up (67N-1 picked up)

PTOC12.Str.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTOC12.Op
No.
2683

Information
67N-1 TRIP (67N-1 TRIP)

0 1

PTOC12.Op.general
device annunciation:

52

1 - ON
0 - OFF

0 1
IEC Status Op.general:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTOC12.ChgSet
No.
1997

Information
Dynamic settings are ACTIVE (Dyn set. ACTIVE)

PTOC12.ChgSet.stVal
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status ChgSet.stVal:

0 - FALSE
1 - TRUE

PTOC13.Mod
No.
2656

Information
67N/67N-TOC switched OFF (67N OFF)

1 x 0

67N-2 PICKUP (P1602) =

x 1 0

PTOC13.Mod.stVal

5 5 1

device annunciation / setting:

1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC13.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOC13.Health.stVal
device annunciation:

1 - ON
0 - OFF

0 1
3 1

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PTOC13.Str
No.
2646

Information
67N-2 picked up (67N-2 picked up)

PTOC13.Str.general
device annunciation:

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

0 1
0 1

IEC Status Str.general:

0 - FALSE
1 - TRUE

53

Mapping
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTOC13.Op
No.
2679

Information
67N-2 TRIP (67N-2 TRIP)

0 1

PTOC13.Op.general
device annunciation:

0 1

1 - ON
0 - OFF

IEC Status Op.general:

0 - FALSE
1 - TRUE

PTOC13.ChgSet
No.
1997

Information
Dynamic settings are ACTIVE (Dyn set. ACTIVE)

PTOC13.ChgSet.stVal
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status ChgSet.stVal:

0 - FALSE
1 - TRUE

PTOC20.Mod
No.
2656

Information
67N/67N-TOC switched OFF (67N OFF)

1 x 0

67N-3 PICKUP (P1628) =

x 1 0

PTOC20.Mod.stVal

5 5 1

device annunciation / setting:

1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC20.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOC20.Health.stVal
device annunciation:

54

1 - ON
0 - OFF

0 1
3 1

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTOC20.Str
No.
2698

Information
67N-3 picked up (67N-3 picked up)

PTOC20.Str.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTOC20.Op
No.
2603

Information
67N-3 TRIP (67N-3 TRIP)

0 1

PTOC20.Op.general
device annunciation:

0 1

1 - ON
0 - OFF

IEC Status Op.general:

0 - FALSE
1 - TRUE

PTOC20.ChgSet
No.
1997

Information
Dynamic settings are ACTIVE (Dyn set. ACTIVE)

PTOC20.ChgSet.stVal
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status ChgSet.stVal:

0 - FALSE
1 - TRUE

PTOC4.Mod
No.
2656

Information
67N/67N-TOC switched OFF (67N OFF)

1 x 0

M.of PU TD (P1630) =

x 1 0

PTOC4.Mod.stVal
device annunciation / setting:

5 5 1
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

55

Mapping
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTOC4.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOC4.Health.stVal
device annunciation:

1 - ON
0 - OFF

0 1
3 1

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PTOC4.Str
No.
2684

Information
67N-TOC picked up (67N-TOCPickedup)

PTOC4.Str.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTOC4.Op
No.
2686

Information
67N-TOC TRIP (67N-TOC TRIP)

PTOC4.Op.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Op.general:

0 - FALSE
1 - TRUE

PTOC4.ChgSet
No.
1997

Information
Dynamic settings are ACTIVE (Dyn set. ACTIVE)

PTOC4.ChgSet.stVal
device annunciation:

56

1 - ON
0 - OFF

0 1
0 1

IEC Status ChgSet.stVal:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

2.4.3

Directional Overcurrent Protection 67N (PTRC3)

PTRC3.Mod
No.

Information
67/67-TOC switched OFF (67/67-TOC OFF) (I 2651) and
67N/67N-TOC switched OFF (67N OFF) (I 2656)

PTRC3.Mod.stVal
device annunciation / setting:

1 0

5 1
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTRC3.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTRC3.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PTRC3.Str
No.
2691

Information
67/67N picked up (67/67N pickedup)

PTRC3.Str.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Str.general:

0 - FALSE
1 - TRUE

57

Mapping
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTRC3.Str.dirGeneral
No.
2691

Information
67/67N picked up (67/67N picked up)

0 1 1 1 1

Phase A forward (Phase A forward) (I 2628) or


Phase B forward (Phase B forward) (I 2629) or
Phase C forward (Phase C forward) (I 2630) or
Ground forward (Ground forward) (I 2635)

x 0 1 0 1

Phase A reverse (Phase A reverse) (I 2632) or


Phase B reverse (Phase B reverse) (I 2633) or
Phase C reverse (Phase C reverse) (I 2634) or
Ground reverse (Ground reverse) (I 2636)

x 0 0 1 1

PTRC3.Str.dirGeneral
device annunciation:

0 0 1 2 3

1 - ON
0 - OFF

IEC Status Str.dirGeneral:

0 - UNKNOWN
1 - FORWARD
2 - BACKWARD
3 - BOTH

PTRC3.Str.phsA
No.
2692

Information
67/67-TOC Phase A picked up (67 A picked up)

PTRC3.Str.phsA
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.phsA:

0 - FALSE
1 - TRUE

PTRC3.Str.dirPhsA
No.

Information

2692

67/67-TOC Phase A picked up (67 A picked up)

0 1 1 1 1

2628

Phase A forward (Phase A forward)

x 0 1 0 1

2632

Phase A reverse (Phase A reverse)

x 0 0 1 1

PTRC3.Str.dirPhsA
device annunciation:

58

0 0 1 2 3
1 - ON
0 - OFF
x - irrelevant

IEC Status Str.dirPhsA:

0 - UNKNOWN
1 - FORWARD
2 - BACKWARD

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTRC3.Str.phsB
No.
2693

Information
67/67-TOC Phase B picked up (67 B picked up)

PTRC3.Str.phsB
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.phsB:

0 - FALSE
1 - TRUE

PTRC3.Str.dirPhsB
No.

Information

2693

67/67-TOC Phase B picked up (67 B picked up)

0 1 1 1 1

2629

Phase B forward (Phase B forward)

x 0 1 0 1

2633

Phase B reverse (Phase B reverse)

x 0 0 1 1

PTRC3.Str.dirPhsB
device annunciation:

0 0 1 2 3
1 - ON
0 - OFF
x - irrelevant

IEC Status Str.dirPhsB:

0 - UNKNOWN
1 - FORWARD
2 - BACKWARD

PTRC3.Str.phsC
No.
2694

Information
67/67-TOC Phase C picked up (67 C picked up)

PTRC3.Str.phsC
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.phsC:

0 - FALSE
1 - TRUE

PTRC3.Str.dirPhsC
No.

Information

2694

67/67-TOC Phase C picked up (67 C picked up)

0 1 1 1 1

2630

Phase C forward (Phase C forward)

x 0 1 0 1

2634

Phase C reverse (Phase C reverse)

x 0 0 1 1

PTRC3.Str.dirPhsC
device annunciation:

0 0 1 2 3
1 - ON
0 - OFF
x - irrelevant

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Str.dirPhsC:

0 - UNKNOWN
1 - FORWARD
2 - BACKWARD

59

Mapping
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTRC3.Str.neut
No.
2695

Information
67N/67N-TOC picked up (67N picked up)

PTRC3.Str.neut
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.neut:

0 - FALSE
1 - TRUE

PTRC3.Str.dirNeut
No.

Information

2695

67N/67N-TOC picked up (67N picked up)

0 1 1 1 1

2635

Ground forward (Ground forward)

x 0 1 0 1

2636

Ground reverse (Ground reverse)

x 0 0 1 1

PTRC3.Str.dirNeut
device annunciation:

0 0 1 2 3
1 - ON
0 - OFF
x - irrelevant

IEC Status Str.dirPhsC:

0 - UNKNOWN
1 - FORWARD
2 - BACKWARD

PTRC3.Op
No.
2696

Information
67/67N TRIP (67/67N TRIP)

PTRC3.Op.general
device annunciation:

60

0 1
0 1

1 - ON
0 - OFF

IEC Status Op.general:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.5 Single-Phase Overcurrent Protection (PTOC16, PTOC17)

2.5

Single-Phase Overcurrent Protection (PTOC16, PTOC17)

PTOC16.Mod
No.
5961

Information
50 1Ph is OFF (50 1Ph OFF)

1 x 0

50 1Ph-1 PICKUP (P2705) =

x 1 0

PTOC16.Mod.stVal

5 5 1

device annunciation / setting:

1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC16.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOC16.Health.stVal
device annunciation:

1 - ON
0 - OFF

0 1
3 1

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PTOC16.Str
No.
5974

Information
50 1Ph-1 picked up (50 1Ph-1 PU)

PTOC16.Str.general
device annunciation:

1 - ON
0 - OFF

0 1
0 1

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTOC16.Op
No.

Information

5975

50 1Ph-1 TRIP (50 1Ph-1 TRIP)

PTOC16.Op.general
device annunciation:

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

0 1
0 1

IEC Status Op.general:

0 - FALSE
1 - TRUE

61

Mapping
2.5 Single-Phase Overcurrent Protection (PTOC16, PTOC17)

PTOC17.Mod
No.
5961

Information
50 1Ph is OFF (50 1Ph OFF)

1 x 0

50 1Ph-2 PICKUP (P2703) =

x 1 0

PTOC17.Mod.stVal

5 5 1

device annunciation / setting:

1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC17.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOC17.Health.stVal
device annunciation:

62

1 - ON
0 - OFF

0 1
3 1

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.5 Single-Phase Overcurrent Protection (PTOC16, PTOC17)

PTOC17.Str
No.
5977

Information
50 1Ph-2 picked up (50 1Ph-2 PU)

PTOC17.Str.general
device annunciation:

1 - ON
0 - OFF

0 1
0 1

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTOC17.Op
No.

Information

5979

50 1Ph-2 TRIP (50 1Ph-2 TRIP)

PTOC17.Op.general
device annunciation:

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

0 1
0 1

IEC Status Op.general:

0 - FALSE
1 - TRUE

63

Mapping
2.6 Voltage Protection 27, 59 (PTUVx, PTOVx)

2.6

Voltage Protection 27, 59 (PTUVx, PTOVx)

2.6.1

Undervoltage Protection 27 (PTUV1)

PTUV1.Mod
No.
6530

Information
27 Undervoltage protection switched OFF (27 OFF)

1 0

PTUV1.Mod.stVal
device annunciation:

5 1
1 - ON
0 - OFF
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTUV1.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTUV1.Health.stVal
device annunciation:

64

0 1
3 1

1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.6 Voltage Protection 27, 59 (PTUVx, PTOVx)

PTUV1.Str
No.

Information

6533

27-1 Undervoltage picked up (27-1 picked up)

0 x 1

6534

27-1 Undervoltage PICKUP w/curr. superv (27-1 PU CS)

0 1 x

PTUV1.Str.general
device annunciation:

0 1 1
1 - ON
0 - OFF
x - irrelevant

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTUV1.Op
No.
6539

Information
27-1 Undervoltage TRIP (27-1 TRIP)

PTUV1.Op.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Op.general:

0 - FALSE
1 - TRUE

65

Mapping
2.6 Voltage Protection 27, 59 (PTUVx, PTOVx)

2.6.2

Undervoltage Protection 27 (PTUV2)

PTUV2.Mod
No.
6530

Information
27 Undervoltage protection switched OFF (27 OFF)

1 0

PTUV2.Mod.stVal
device annunciation:

5 1
1 - ON
0 - OFF
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTUV2.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTUV2.Health.stVal
device annunciation:

66

0 1
3 1

1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.6 Voltage Protection 27, 59 (PTUVx, PTOVx)

PTUV2.Str
No.

Information

6537

27-2 Undervoltage picked up (27-2 picked up)

0 x 1

6538

27-2 Undervoltage PICKUP w/curr. superv (27-2 PU CS)

0 1 x

PTUV2.Str.general
device annunciation:

0 1 1
1 - ON
0 - OFF
X - irrelevant

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTUV2.Op
No.
6540

Information
27-2 Undervoltage TRIP (27-2 TRIP)

PTUV2.Op.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Op.general:

0 - FALSE
1 - TRUE

67

Mapping
2.6 Voltage Protection 27, 59 (PTUVx, PTOVx)

2.6.3

Overvoltage Protection 59 (PTOV1)

PTOV1.Mod
No.
6565

Information
59-Overvoltage protection switched OFF (59 OFF)

1 0

PTOV1.Mod.stVal
device annunciation / setting:

5 1
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOV1.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOV1.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PTOV1.Str
No.
6568

Information
59 picked up (59-1 picked up)

PTOV1.Str.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTOV1.Op
No.
6570

Information
59 TRIP (59-1 TRIP)

0 1

PTOV1.Op.general
device annunciation:

68

0 1
1 - ON
0 - OFF

IEC Status Op.general:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.6 Voltage Protection 27, 59 (PTUVx, PTOVx)

2.6.4

Overvoltage Protection 59 (PTOV2)

PTOV2.Mod
No.
6565

Information
59-Overvoltage protection switched OFF (59 OFF)

1 0

PTOV2.Mod.stVal
device annunciation / setting:

5 1
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOV2.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOV2.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PTOV2.Str
No.
6571

Information
59-2 Overvoltage V>> picked up (59-2 picked up)

PTOV2.Str.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTOV2.Op
No.
6573

Information
59-2 Overvoltage V>> TRIP (59-2 TRIP)

PTOV2.Op.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Op.general:

0 - FALSE
1 - TRUE

69

Mapping
2.7 Negative Sequence Protection 46 (PTOC14, PTOC15, PTOC5)

2.7

Negative Sequence Protection 46 (PTOC14, PTOC15, PTOC5)

PTOC14.Mod
No.
5151

Information
46 switched OFF (46 OFF)

1 0

PTOC14.Mod.stVal

5 1

device annunciation / setting:

1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC14.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOC14.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PTOC14.Str
No.

Information

5165

46-1 picked up (46-1 picked up)

PTOC14.Str.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTOC14.Op
No.

Information
46-1 TRIP (46-1 TRIP)

0 1

PTOC14.Op.general
device annunciation / setting:

70

0 1
1 - ON / TRUE
0 - OFF / FALSE

IEC Status Op.general:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.7 Negative Sequence Protection 46 (PTOC14, PTOC15, PTOC5)

PTOC15.Mod
No.
5151

Information
46 switched OFF (46 OFF)

1 0

PTOC15.Mod.stVal

5 1

device annunciation / setting:

1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC15.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOC15.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PTOC15.Str
No.

Information

5159

46-2 picked up (46-2 picked up)

PTOC15.Str.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTOC15.Op
No.

Information
46-2 TRIP (46-2 TRIP)

0 1

PTOC15.Op.general
device annunciation / setting:

0 1
1 - ON / TRUE
0 - OFF / FALSE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Op.general:

0 - FALSE
1 - TRUE

71

Mapping
2.7 Negative Sequence Protection 46 (PTOC14, PTOC15, PTOC5)

PTOC5.Mod
No.
5151

Information
46 switched OFF (46 OFF)

1 0

PTOC5.Mod.stVal

5 1

device annunciation / setting:

1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC5.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOC5.Health.stVal
device annunciation:

72

1 - ON
0 - OFF

0 1
3 1

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.7 Negative Sequence Protection 46 (PTOC14, PTOC15, PTOC5)

PTOC5.Str
No.
5166

Information
46-TOC picked up (46-TOC pickedup)

PTOC5.Str.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTOC5.Op
No.

Information
46-TOC TRIP (46-TOC TRIP)

PTOC5.Op.general
device annunciation / setting:

0 1
0 1

1 - ON / TRUE
0 - OFF / FALSE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Op.general:

0 - FALSE
1 - TRUE

73

Mapping
2.8 Motor Protection (PMSS1, PMRI1)

2.8

Motor Protection (PMSS1, PMRI1)

2.8.1

Motor Starting Protection 48 (PMSS1)

PMSS1.Mod
No.
6811

Information
Startup supervision OFF (START-SUP OFF)

1 0

PMSS1.Mod.stVal

5 1

device annunciation / setting:

1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PMSS1.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PMSS1.Health.stVal
device annunciation:

74

1 - ON
0 - OFF

0 1
3 1

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.8 Motor Protection (PMSS1, PMRI1)

PMSS1.Str
No.
6823

Information
Startup supervision Pickup (START-SUP pu)

PMSS1.Str.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

PMSS1.Op
No.
6821

Information
Startup supervision TRIP (START-SUP TRIP)

PMSS1.Op.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Op.general:

0 - FALSE
1 - TRUE

75

Mapping
2.8 Motor Protection (PMSS1, PMRI1)

2.8.2

Motor Restart Inhibit 66 (PMRI1)

PMRI1.Mod
No.
4824

Information
66 Motor start protection OFF (66 OFF))

1 0

PMRI1.Mod.stVal
device annunciation:

5 1
1 - ON
0 - OFF
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PMRI1.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PMRI1.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PMRI1.Op
No.
4827

Information
66 Motor start protection TRIP (66 TRIP)

0 1

PMRI1.Op.general
device annunciation:

0 1
1 - ON
0 - OFF

IEC Status Op.general:

0 - FALSE
1 - TRUE

PMRI1.StrInhTmm
No.
809

76

Information
Time untill release of reclose-blocking (T reclose=)

Value
PMRI1.StrInhTmm.stVal Absolute value

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.9 Load Jam Protection (PMLJ1)

2.9

Load Jam Protection (PMLJ1)

Function available with Firmware


PMLJ1.Mod
No.
10022

Information
Load Jam Protection is OFF (JAM PROT.OFF)

1 0

PMLJ1.Mod.stVal
device annunciation / setting:

5 1
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PMLJ1.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PMLJ1.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

77

Mapping
2.9 Load Jam Protection (PMLJ1)

PMLJ1.Str
No.

Information

10025

Load Jam Protection picked up (Load Jam pickup)

PMLJ1.Str.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

PMLJ1.Op
No.
10026

Information
Load Jam Protection TRIP (Load Jam TRIP)

PMLJ1.Op.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Op.general:

0 - FALSE
1 - TRUE

PMLJ1.LodJamAlm
No.
10024

Information
Load Jam Protection alarm (Load Jam alarm)

PMLJ1.LodJamAlm.stVal
device annunciation:

78

1 - ON
0 - OFF

0 1
0 1

IEC Status Op.general:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

2.10

Frequency protection 81 O/U (PTUFx, PTOFx)

2.10.1

Frequency protection 81-1 U (PTUF1)

PTUF1.Mod
No.
5211

Information
81 OFF (81 OFF)

x 1 0

81-1 PICKUP (P5403/5404) < Rated Frequency (P214)

0 1 1

PTUF1.Mod.stVal
device annunciation / setting:

5 5 1
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTUF1.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTUF1.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

79

Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

PTUF1.Str
No.
5232

Information
81-1 picked up (81-1 picked up)

0 0 1 1

81-1 PICKUP (P5403/5404) < Rated Frequency (P214)

0 1 0 1

PTUF1.Str.general
device annunciation / setting:

0 0 0 1
1 - ON / TRUE
0 - OFF / FALSE

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTUF1.Op
No.
5236

Information
81-1 TRIP (81-1 TRIP)

0 0 1 1

81-1 PICKUP (P5403/5404) < Rated Frequency (P214)

0 1 0 1

PTUF1.Op.general
device annunciation / setting:

0 0 0 1
1 - ON / TRUE
0 - OFF / FALSE

IEC Status Op.general:

0 - FALSE
1 - TRUE

PTUF1.BlkV
No.
5214

Information
81 Under Voltage Block (81 Under V Blk)

0 0 1 1

81-1 PICKUP (P5403/5404) < Rated Frequency (P214)

0 1 0 1

PTUF1.BlkV.stVal
device annunciation / setting:

80

0 0 0 1
1 - ON / TRUE
0 - OFF / FALSE

IEC Status BlkV.stVal:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

2.10.2

Frequency protection 81-2 U (PTUF2)

PTUF2.Mod
No.
5211

Information
81 OFF (81 OFF)

x 1 0

81-2 PICKUP (P5406/5407) < Rated Frequency (P214)

0 1 1

PTUF2.Mod.stVal
device annunciation / setting:

5 5 1
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTUF2.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTUF2.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

81

Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

PTUF2.Str
No.
5233

Information
81-2 picked up (81-2 picked up)

0 0 1 1

81-2 PICKUP (P5406/5407) < Rated Frequency (P214)

0 1 0 1

PTUF2.Str.general
device annunciation / setting:

0 0 0 1
1 - ON / TRUE
0 - OFF / FALSE

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTUF2.Op
No.
5237

Information
81-2 TRIP (81-2 TRIP)

0 0 1 1

81-2 PICKUP (P5406/5407) < Rated Frequency (P214)

0 1 0 1

PTUF2.Op.general
device annunciation / setting:

0 0 0 1
1 - ON / TRUE
0 - OFF / FALSE

IEC Status Op.general:

0 - FALSE
1 - TRUE

PTUF2.BlkV
No.
5214

Information
81 Under Voltage Block (81 Under V Blk)

0 0 1 1

81-2 PICKUP (P5406/5407) < Rated Frequency (P214)

0 1 0 1

PTUF2.BlkV.stVal
device annunciation / setting:

82

0 0 0 1
1 - ON / TRUE
0 - OFF / FALSE

IEC Status BlkV.stVal:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

2.10.3

Frequency protection 81-3 U (PTUF3)

PTUF3.Mod
No.
5211

Information
81 OFF (81 OFF)

x 1 0

81-3 PICKUP (P5409/5410) < Rated Frequency (P214)

0 1 1

PTUF3.Mod.stVal
device annunciation / setting:

5 5 1
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTUF3.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTUF3.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

83

Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

PTUF3.Str
No.
5234

Information
81-3 picked up (81-3 picked up)

0 0 1 1

81-3 PICKUP (P5409/5410) < Rated Frequency (P214)

0 1 0 1

PTUF3.Str.general
device annunciation / setting:

0 0 0 1
1 - ON / TRUE
0 - OFF / FALSE

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTUF3.Op
No.
5238

Information
81-3 TRIP (81-3 TRIP)

0 0 1 1

81-3 PICKUP (P5409/5410) < Rated Frequency (P214)

0 1 0 1

PTUF3.Op.general
device annunciation / setting:

0 0 0 1
1 - ON / TRUE
0 - OFF / FALSE

IEC Status Op.general:

0 - FALSE
1 - TRUE

PTUF3.BlkV
No.
5214

Information
81 Under Voltage Block (81 Under V Blk)

0 0 1 1

81-3 PICKUP (P5409/5410) < Rated Frequency (P214)

0 1 0 1

PTUF3.BlkV.stVal
device annunciation / setting:

84

0 0 0 1
1 - ON / TRUE
0 - OFF / FALSE

IEC Status BlkV.stVal:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

2.10.4

Frequency protection 81-4 U (PTUF4)

PTUF4.Mod
No.
5211

Information
81 OFF (81 OFF)

x 1 0

81-4 PICKUP (P5412/5413) < Rated Frequency (P214)

0 1 1

PTUF4.Mod.stVal
device annunciation / setting:

5 5 1
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTUF4.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTUF4.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

85

Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

PTUF4.Str
No.
5235

Information
81-4 picked up (81-4 picked up)

0 0 1 1

81-4 PICKUP (P5412/5413) < Rated Frequency (P214)

0 1 0 1

PTUF4.Str.general
device annunciation / setting:

0 0 0 1
1 - ON / TRUE
0 - OFF / FALSE

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTUF4.Op
No.
5239

Information
81-4 TRIP (81-4 TRIP)

0 0 1 1

81-4 PICKUP (P5412/5413) < Rated Frequency (P214)

0 1 0 1

PTUF4.Op.general
device annunciation / setting:

0 0 0 1
1 - ON / TRUE
0 - OFF / FALSE

IEC Status Op.general:

0 - FALSE
1 - TRUE

PTUF4.BlkV
No.
5214

Information
81 Under Voltage Block (81 Under V Blk)

0 0 1 1

81-4 PICKUP (P5412/5413) < Rated Frequency (P214)

0 1 0 1

PTUF4.BlkV.stVal
device annunciation / setting:

86

0 0 0 1
1 - ON / TRUE
0 - OFF / FALSE

IEC Status BlkV.stVal:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

2.10.5

Frequency protection 81-1 O (PTOF1)

PTOF1.Mod
No.
5211

Information
81 OFF (81 OFF)

x 1 0

81-1 PICKUP (P5403/5404) Rated Frequency (P214) 1 x 0


PTOF1.Mod.stVal
device annunciation / setting:

5 5 1
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOF1.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOF1.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

87

Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

PTOF1.Str
No.
5232

Information
81-1 picked up (81-1 picked up)

0 0 1 1

81-1 PICKUP (P5403/5404) < Rated Frequency (P214)

0 1 0 1

PTOF1.Str.general
device annunciation / setting:

0 0 1 0
1 - ON / TRUE
0 - OFF / FALSE

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTOF1.Op
No.
5236

Information
81-1 TRIP (81-1 TRIP)

0 0 1 1

81-1 PICKUP (P5403/5404) < Rated Frequency (P214)

0 1 0 1

PTOF1.Op.general
device annunciation / setting:

0 0 1 0
1 - ON / TRUE
0 - OFF / FALSE

IEC Status Op.general:

0 - FALSE
1 - TRUE

PTOF1.BlkV
No.
5214

Information
81 Under Voltage Block (81 Under V Blk)

0 0 1 1

81-1 PICKUP (P5403/5404) < Rated Frequency (P214)

0 1 0 1

PTOF1.BlkV.stVal
device annunciation / setting:

88

0 0 1 0
1 - ON / TRUE
0 - OFF / FALSE

IEC Status BlkV.stVal:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

2.10.6

Frequency protection 81-2 O (PTOF2)

PTOF2.Mod
No.
5211

Information
81 OFF (81 OFF)

x 1 0

81-2 PICKUP (P5406/5407) Rated Frequency (P214) 1 x 0


PTOF2.Mod.stVal
device annunciation / setting:

5 5 1
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOF2.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOF2.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

89

Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

PTOF2.Str
No.
5233

Information
81-2 picked up (81-2 picked up)

0 0 1 1

81-2 PICKUP (P5406/5407) < Rated Frequency (P214)

0 1 0 1

PTOF2.Str.general
device annunciation / setting:

0 0 1 0
1 - ON / TRUE
0 - OFF / FALSE

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTOF2.Op
No.
5237

Information
81-2 TRIP (81-2 TRIP)

0 0 1 1

81-2 PICKUP (P5406/5407) < Rated Frequency (P214)

0 1 0 1

PTOF2.Op.general
device annunciation / setting:

0 0 1 0
1 - ON / TRUE
0 - OFF / FALSE

IEC Status Op.general:

0 - FALSE
1 - TRUE

PTOF2.BlkV
No.
5214

Information
81 Under Voltage Block (81 Under V Blk)

0 0 1 1

81-2 PICKUP (P5406/5407) < Rated Frequency (P214)

0 1 0 1

PTOF2.BlkV.stVal
device annunciation / setting:

90

0 0 1 0
1 - ON / TRUE
0 - OFF / FALSE

IEC Status BlkV.stVal:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

2.10.7

Frequency protection 81-3 O (PTOF3)

PTOF3.Mod
No.
5211

Information
81 OFF (81 OFF)

x 1 0

81-3 PICKUP (P5409/5410) Rated Frequency (P214) 1 x 0


PTOF1.Mod.stVal
device annunciation / setting:

5 5 1
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOF3.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOF3.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

91

Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

PTOF3.Str
No.
5234

Information
81-3 picked up (81-3 picked up)

0 0 1 1

81-3 PICKUP (P5409/5410) < Rated Frequency (P214)

0 1 0 1

PTOF3.Str.general
device annunciation / setting:

0 0 1 0
1 - ON / TRUE
0 - OFF / FALSE

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTOF3.Op
No.
5238

Information
81-3 TRIP (81-3 TRIP)

0 0 1 1

81-3 PICKUP (P5409/5410) < Rated Frequency (P214)

0 1 0 1

PTOF3.Op.general
device annunciation / setting:

0 0 1 0
1 - ON / TRUE
0 - OFF / FALSE

IEC Status Op.general:

0 - FALSE
1 - TRUE

PTOF3.BlkV
No.
5214

Information
81 Under Voltage Block (81 Under V Blk)

0 0 1 1

81-3 PICKUP (P5409/5410) < Rated Frequency (P214)

0 1 0 1

PTOF3.BlkV.stVal
device annunciation / setting:

92

0 0 1 0
1 - ON / TRUE
0 - OFF / FALSE

IEC Status BlkV.stVal:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

2.10.8

Frequency protection 81-4 O (PTOF4)

PTOF4.Mod
No.
5211

Information
81 OFF (81 OFF)

x 1 0

81-4 PICKUP (P5412/5413) Rated Frequency (P214) 1 x 0


PTOF4.Mod.stVal
device annunciation / setting:

5 5 1
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOF4.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTOF4.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

93

Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

PTOF4.Str
No.
5235

Information
81-4 picked up (81-4 picked up)

0 0 1 1

81-4 PICKUP (P5412/5413) < Rated Frequency (P214)

0 1 0 1

PTOF4.Str.general
device annunciation / setting:

0 0 1 0
1 - ON / TRUE
0 - OFF / FALSE

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTOF4.Op
No.
5239

Information
81-4 TRIP (81-4 TRIP)

0 0 1 1

81-4 PICKUP (P5412/5413) < Rated Frequency (P214)

0 1 0 1

PTOF4.Op.general
device annunciation / setting:

0 0 1 0
1 - ON / TRUE
0 - OFF / FALSE

IEC Status Op.general:

0 - FALSE
1 - TRUE

PTOF4.BlkV
No.
5214

Information
81 Under Voltage Block (81 Under V Blk)

0 0 1 1

81-4 PICKUP (P5412/5413) < Rated Frequency (P214)

0 1 0 1

PTOF4.BlkV.stVal
device annunciation / setting:

94

0 0 1 0
1 - ON / TRUE
0 - OFF / FALSE

IEC Status BlkV.stVal:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.11 QV Protection 27/Q (PTUV9)

2.11

QV Protection 27/Q (PTUV9)

PTUV9.Mod
No.
6411

Information
27/Q -Protection off (27/Q OFF)

0 1

PTUV9.Mod.stVal
device annunciation:

5 1
1 - ON
0 - OFF
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTUV9.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTUV9.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PTUV9.Str
No.
6423

Information
27/Q-Protection PICKUP (27/Q PICKUP)

PTUV9.Str.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF
x - irrelevant

IEC Status Str.general:

0 - FALSE
1 - TRUE

PTUV9.Op
No.

Information

6421

27/Q -Protection Gen TRIP (27/Q Gen TRIP)

0 1 0 1

6422

27/Q -Protection Gen TRIP (27/Q Gen TRIP)

0 0 1 1

PTUV9.Op.general
device annunciation:

0 1 1 1
1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Op.general:

0 - FALSE
1 - TRUE

95

Mapping
2.12 Thermal overload protection (PTTR1)

2.12

Thermal overload protection (PTTR1)

PTTR1.Mod
No.
1511

Information
49 Overload Protection is OFF (49 O / L OFF)

1 0

PTTR1.Mod.stVal
device annunciation:

5 1
1 - ON
0 - OFF
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTTR1.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTTR1.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PTTR1.Str
No.
1517

Information
49 Winding Overload (49 Winding O/L)

PTTR1.Str.general
device annunciation:

96

0 1
0 1

1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.12 Thermal overload protection (PTTR1)

PTTR1.Op
No.
1521

Information
49 Thermal Overload TRIP (49 Th O/L TRIP)

0 1

PTTR1.Op.general
device annunciation:

0 1
1 - ON
0 - OFF

IEC Status Op.general:

0 - FALSE
1 - TRUE

PTTR1.AlmThm
No.

Information

1516

49 Overload Alarm! Near Thermal Trip (49 O/L Alarm)

PTTR1.AlmThm.general
device annunciation:

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

0 1
0 1

IEC Status AlmThm.general:

0 - FALSE
1 - TRUE

97

Mapping
2.13 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)

2.13

Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)

2.13.1

Ground Fault Protection 64 (PHIZ1)

PHIZ1.Mod
No.
1211

Information
50Ns/67Ns is OFF (50Ns/67Ns OFF)

1 0

PHIZ1.Mod.stVal
device annunciation / setting:

5 1
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PHIZ1.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PHIZ1.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PHIZ1.Str
No.
1215

Information
64 displacement voltage pick up (64 Pickup)

0 1

PHIZ1.Str.general
device annunciation:

98

0 1
1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.13 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)

PHIZ1.Str.dirGeneral
No.

Information

1215

64 displacement voltage pick up (64 Pickup)

0 x 1 1 1 1

1276

Sensitive Gnd fault in forward direction (SensGnd Forward)

x 0 1 0 1 x

1277

Sensitive Gnd fault in reverse direction (SensGnd Reverse)

x 0 0 1 1 x

1278

Sensitive Gnd fault direction undefined (SensGnd undef.)

x 0 0 0 0 1

PHIZ1.Str.dirGeneral
device annunciation:

1 - ON
0 - OFF
x - irrelevant

0 0 1 2 3 0
IEC Status Str.dirGeneral:

0 - UNKNOWN
1 - FORWARD
2 - BACKWARD
3 - BOTH

PHIZ1.Str.phsA
No.

Information

1215

64 displacement voltage pick up (64 Pickup)

0 x 1 1 1 1

1276

Sensitive Gnd fault in forward direction (SensGnd Forward)

x x 1 0 1 x

1277

Sensitive Gnd fault in reverse direction (SensGnd Reverse)

x x 0 1 1 x

1278

Sensitive Gnd fault direction undefined (SensGnd undef.)

x x 0 0 x 1

1272

Sensitive Ground fault picked up in Ph A (Sens. Gnd Ph A)

x 0 1 1 1 1

PHIZ1.Str.phsA
device annunciation:

0 0 1 1 1 1
1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Str.phsA:

0 -FALSE
1 - TRUE

99

Mapping
2.13 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)

PHIZ1.Str.dirPhsA
No.

Information

1215

64 displacement voltage pick up (64 Pickup)

0 x 1 1 1 1

1276

Sensitive Gnd fault in forward direction (SensGnd Forward)

x x 1 0 1 x

1277

Sensitive Gnd fault in reverse direction (SensGnd Reverse)

x x 0 1 1 x

1278

Sensitive Gnd fault direction undefined (SensGnd undef.)

x x 0 0 x 1

1272

Sensitive Ground fault picked up in Ph A (Sens. Gnd Ph A)

x 0 1 1 1 1

PHIZ1.Str.dirPhsA
device annunciation:

0 0 1 2 0 0
1 - ON
0 - OFF
x - irrelevant

IEC Status Str.dirPhsA:

0 - UNKNOWN
1 - FORWARD
2 - BACKWARD

PHIZ1.Str.phsB
No.

Information

1215

64 displacement voltage pick up (64 Pickup)

0 x 1 1 1 1

1276

Sensitive Gnd fault in forward direction (SensGnd Forward)

x x 1 0 1 x

1277

Sensitive Gnd fault in reverse direction (SensGnd Reverse)

x x 0 1 1 x

1278

Sensitive Gnd fault direction undefined (SensGnd undef.)

x x 0 0 x 1

1273

Sensitive Ground fault picked up in Ph B (Sens. Gnd Ph B)

x 0 1 1 1 1

PHIZ1.Str.phsB
device annunciation:

100

0 0 1 1 1 1
1 - ON
0 - OFF

IEC Status Str.phsB:

0 -FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.13 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)

PHIZ1.Str.dirPhsB
No.

Information

1215

64 displacement voltage pick up (64 Pickup)

0 x 1 1 1 1

1276

Sensitive Gnd fault in forward direction (SensGnd Forward)

x x 1 0 1 x

1277

Sensitive Gnd fault in reverse direction (SensGnd Reverse)

x x 0 1 1 x

1278

Sensitive Gnd fault direction undefined (SensGnd undef.)

x x 0 0 x 1

1273

Sensitive Ground fault picked up in Ph B (Sens. Gnd Ph B)

x 0 1 1 1 1

PHIZ1.Str.dirPhsB
device annunciation:

0 0 1 2 0 0
1 - ON
0 - OFF
x - irrelevant

IEC Status Str.dirPhsB:

0 - UNKNOWN
1 - FORWARD
2 - BACKWARD

PHIZ1.Str.phsC
No.

Information

1215

64 displacement voltage pick up (64 Pickup)

0 x 1 1 1 1

1276

Sensitive Gnd fault in forward direction (SensGnd Forward)

x x 1 0 1 x

1277

Sensitive Gnd fault in reverse direction (SensGnd Reverse)

x x 0 1 1 x

1278

Sensitive Gnd fault direction undefined (SensGnd undef.)

x x 0 0 x 1

1274

Sensitive Ground fault picked up in Ph C (Sens. Gnd Ph C)

x 0 1 1 1 1

PHIZ1.Str.phsC
device annunciation:

0 0 1 1 1 1
1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Str.phsC:

0 -FALSE
1 - TRUE

101

Mapping
2.13 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)

PHIZ1.Str.dirPhsC
No.

Information

1215

64 displacement voltage pick up (64 Pickup)

0 x 1 1 1 1

1276

Sensitive Gnd fault in forward direction (SensGnd Forward)

x x 1 0 1 x

1277

Sensitive Gnd fault in reverse direction (SensGnd Reverse)

x x 0 1 1 x

1278

Sensitive Gnd fault direction undefined (SensGnd undef.)

x x 0 0 x 1

1274

Sensitive Ground fault picked up in Ph C (Sens. Gnd Ph C)

x 0 1 1 1 1

PHIZ1.Str.dirPhsC
device annunciation:

0 0 1 2 0 0
1 - ON
0 - OFF
x - irrelevant

IEC Status Str.dirPhsC:

0 - UNKNOWN
1 - FORWARD
2 - BACKWARD

PHIZ1.Op
No.
1217

Information
64 displacement voltage element TRIP (64 TRIP)

PHIZ1.Op.general
device annunciation:

102

0 1
0 1

1 - ON
0 - OFF

IEC Status Op.general:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.13 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)

2.13.2

Ground Fault Protection 50N(s) (PSDE1, PSDE2)

PSDE1.Mod
No.

Information

1211

50Ns/67Ns is OFF (50Ns/67Ns OFF)

1 0

PSDE1.Mod.stVal
device annunciation / setting:

5 1
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PSDE1.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PSDE1.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PSDE1.Str
No.
1224

Information
50Ns-1 Pickup (50Ns-1 Pickup)

0 1

PSDE1.Str.general
device annunciation:

0 1
1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Str.general:

0 - FALSE
1 - TRUE

103

Mapping
2.13 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)

PSDE1.Str.dirGeneral
No.

Information

1224

50Ns-1 Pickup (50Ns-1 Pickup)

0 1 1 1 1 1

1276

Sensitive Gnd fault in forward direction (SensGnd Forward)

x 0 1 0 1 x

1277

Sensitive Gnd fault in reverse direction (SensGnd Reverse)

x 0 0 1 1 x

1278

Sensitive Gnd fault direction undefined (SensGnd undef.)

x 0 0 0 0 1

PSDE1.Str.dirGeneral
device annunciation:

0 0 1 2 3 0

1 - ON
0 - OFF
x - irrelevant

IEC Status Str.dirGeneral:

0 - UNKNOWN
1 - FORWARD
2 - BACKWARD
3 - BOTH

PSDE1.Op
No.
1226

Information
50Ns-1 TRIP (50Ns-1 TRIP)

PSDE1.Op.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Op.general:

0 - FALSE
1 - TRUE

PSDE2.Mod
No.

Information

1211

50Ns/67Ns is OFF (50Ns/67Ns OFF)

1 0

PSDE2.Mod.stVal
device annunciation / setting:

5 1
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PSDE2.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PSDE2.Health.stVal
device annunciation:

104

0 1
3 1

1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.13 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)

PSDE2.Str
No.
1221

Information
50Ns-2 Pickup (50Ns-2 Pickup)

0 1

PSDE2.Str.general
device annunciation:

0 1
1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

PSDE2.Str.dirGeneral
No.

Information

1221

50Ns-2 Pickup (50Ns-2 Pickup)

0 1 1 1 1 1

1276

Sensitive Gnd fault in forward direction (SensGnd Forward)

x 0 1 0 1 x

1277

Sensitive Gnd fault in reverse direction (SensGnd Reverse)

x 0 0 1 1 x

1278

Sensitive Gnd fault direction undefined (SensGnd undef.)

x 0 0 0 0 1

PSDE2.Str.dirGeneral
device annunciation:

0 0 1 2 3 0

1 - ON
0 - OFF
x - irrelevant

IEC Status Str.dirGeneral:

0 - UNKNOWN
1 - FORWARD
2 - BACKWARD
3 - BOTH

PSDE2.Op
No.
1223

Information
50Ns-2 TRIP (50Ns-2 TRIP)

PSDE2.Op.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Op.general:

0 - FALSE
1 - TRUE

105

Mapping
2.13 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)

2.13.3

51 N(s) (PSDE3)

PSDE3.Mod
No.

Information

1211

50Ns/67Ns is OFF (50Ns/67Ns OFF)

1 x 0

M.of PU TD (P3131) =

x 1 0

PSDE3.Mod.stVal
device annunciation / setting:

5 5 1
1 - ON / TRUE
0 - OFF / FALSE
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PSDE3.Health
No.
51
16029

Information
Device is Operational and Protecting (Device OK)

x 0 1

sens.grd.flt. 51Ns BLOCKED Setting Error (51Ns BLK PaErr)

1 x 0

PSDE3.Health.stVal
device annunciation:

3 3 1
1 - ON
0 - OFF
x - irrelevant

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PSDE3.Str
No.
1227

Information
51Ns picked up (51Ns Pickup)

0 1

PSDE3.Str.general
device annunciation:

106

0 1
1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.13 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)

PSDE3.Str.dirGeneral
No.

Information

1227

51Ns picked up (51Ns Pickup)

0 1 1 1 1 1

1276

Sensitive Gnd fault in forward direction (SensGnd Forward)

x 0 1 0 1 x

1277

Sensitive Gnd fault in reverse direction (SensGnd Reverse)

x 0 0 1 1 x

1278

Sensitive Gnd fault direction undefined (SensGnd undef.)

x 0 0 0 0 1

PSDE3.Str.dirGeneral
device annunciation:

0 0 1 2 3 0

1 - ON
0 - OFF
x - irrelevant

IEC Status Str.dirGeneral:

0 - UNKNOWN
1 - FORWARD
2 - BACKWARD
3 - BOTH

PSDE3.Op
No.
1229

Information
51Ns TRIP (51Ns TRIP)

0 1

PSDE3.Op.general
device annunciation:

0 1
1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Op.general:

0 - FALSE
1 - TRUE

107

Mapping
2.14 Automatic Reclosing System 79 (RREC1)

2.14

Automatic Reclosing System 79 (RREC1)

RREC1.Mod
No.
2781

Information
79 Auto recloser is switched OFF (79 OFF)

1 0

RREC1.Mod.stVal
device annunciation:

5 1
1 - ON
0 - OFF
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

RREC1.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

RREC1.Health.stVal
device annunciation:

108

1 - ON
0 - OFF

0 1
3 1

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.14 Automatic Reclosing System 79 (RREC1)

RREC1.Op
No.

Information

2851

79 - Close command (79 Close)

RREC1.Op.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Op.general:

0 - FALSE
1 - TRUE

RREC1.AutoRecSt
No.

Information

2801

79 - in progress (79 in progress)

1 1 0 0

2862

79 - cycle successful (79 Successful)

1 0 1 0

RREC1.AutoRecSt.stVal
device annunciation:

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

3 2 3 1
IEC Status AutoRecST.stVal:

1 - ready
2 - in progress
3 - successful

109

Mapping
2.15 Fault Locator (RFLO1)

2.15

Fault Locator (RFLO1)

RFLO1.Mod
No.

Information
Fault Locator (P180) = Enabled

RFLO1.Mod.stVal
device annunciation / setting:

1 0
1 5

1 - ON / TRUE
0 - OFF / FALSE

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

RFLO1.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

0 1

RFLO1.Health.stVal
device annunciation:

110

3 1
1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.15 Fault Locator (RFLO1)

RFLO1.FltZ
No.

Information
Absolute value of the fault
impedance

Angle of the fault impedance

Value
RFLO1.FltZ.cVal.mag.f

Measured value

Absolute value

RFLO1.FltZ.units.SIUnit

30

(Ohm)

RFLO1.FltZ.units.multiplier

Measured value

Angle in

RFLO1.FltZ.cVal.ang.f

RFLO1.FltDiskm
No.
1119
or
1122

Information
Flt Locator: Distance to fault
(dist =)

Value
RFLO1.FltDiskm.mag.f

Measured value

Absolute value

RFLO1.FltDiskm.units.SIUnit

Meter

RFLO1.FltDiskm.units.multiplier

Kilo

Measured value

Absolute value

RFLO1.FltDisPrc.units.SIUnit

NONE

RFLO1.FltDisPrc.multiplier

RFLO1.FltDisPrc
No.
1120

Information

Value

Flt Locator: Distance [%] to fault RFLO1.FltDisPrc.mag.f


(d[%] =)

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

111

Mapping
2.16 Circuit breaker failure protection 50BF(RBRF1)

2.16

Circuit breaker failure protection 50BF(RBRF1)

RBRF1.Mod
No.
1451

Information
Breaker failure is switched OFF (BkrFail OFF)

RBRF1.Mod.stVal
device annunciation:

1 0
5 1

1 - ON
0 - OFF

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

RBRF1.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

RBRF1.Health.stVal
device annunciation:

1 - ON
0 - OFF

0 1
3 1

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

RBRF1.Str
No.

Information

1456

50BF (internal) PICKUP (50BF int Pickup)

0 0 1 1

1457

50BF (external) PICKUP (50BF ext Pickup)

0 1 0 1

RBRF1.Str.general
device annunciation:

112

0 1 1 1
1 - ON
0 - OFF

IEC Status Str.general:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.16 Circuit breaker failure protection 50BF(RBRF1)

RBRF1.OpEx
No.
1481

Information
50BF (external) TRIP (50BF ext TRIP)

RBRF1.OpEx.general
device annunciation:

1 - ON
0 - OFF

0 1
0 1

IEC Status OpEx.general:

0 - FALSE
1 - TRUE

RBRF1.OpIn
No.
1480

Information
50BF (internal) TRIP (50BF int TRIP)

RBRF1.OpIn.general
device annunciation:

1 - ON
0 - OFF
x - irrelevant

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

0 1
0 1

IEC Status OpIn.general:

0 - FALSE
1 - TRUE

113

Mapping
2.17 Synchronism and Voltage Check 25 (RSYNx)

2.17

Synchronism and Voltage Check 25 (RSYNx)

RSYN1.Mod
No.

Information

170.2101 Sync-group 1 is switched OFF (25-1 OFF)


RSYN1.Mod.stVal
device annunciation:

0 1
1 5

1 - ON
0 - OFF
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

RSYN1.Health
No.

Information

170.0050 25 Synchronization Error (25 Sync. Error)


51

x x 1 0

Device is Operational and Protecting (Device OK)

x x 1 1

170.2096 25 Multiple selection of func-groups (25 FG-Error)

1 x 0 0

170.2097 25 Setting error (25 Set-Error)

x 1 0 0

RSYN1.Health.stVal
device annunciation:

1 - ON
0 - OFF
x - irrelevant

3 3 2 1
IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

RSYN1.Rel
No.

Information

170.0049 25 Sync. Release of CLOSE Command (25 CloseRelease)


RSYN1.Rel.stVal
device annunciation:

114

0 1
0 1

1 - ON
0 - OFF

IEC Status Rel.stVal:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.17 Synchronism and Voltage Check 25 (RSYNx)

RSYN1.VInd
No.

Information

170.2030 25 Voltage difference (Vdiff) okay (25 Vdiff ok)

0 1

RSYN1.VInd.stVal
device annunciation:

1 0
1 - ON
0 - OFF

IEC Status VInd.stVal:

0 - FALSE
1 - TRUE

RSYN1.AngInd
No.

Information

170.2032 25 Angle difference (alphadiff) okay (25 diff ok)

0 1

RSYN1.AngInd.stVal
device annunciation:

1 - ON
0 - OFF

1 0
IEC Status AngInd.stVal:

0 - FALSE
1 - TRUE

RSYN1.HzInd
No.

Information

170.2031 25 Frequency difference (fdiff) okay (25 fdiff ok)

0 1

RSYN1.HzInd.stVal
device annunciation:

1 0
1 - ON
0 - OFF

IEC Status HzInd.stVal:

0 - FALSE
1 - TRUE

RSYN1.SynPrg
No.

Information

170.2022 25-group 1: measurement in progress (25-1 meas.)

0 1

RSYN1.SynPrg.stVal
device annunciation:

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

0 1
IEC Status SynPrg.stVal:

0 - FALSE
1 - TRUE

115

Mapping
2.17 Synchronism and Voltage Check 25 (RSYNx)

RSYN1.DifVCIc
No.

Information

170.2054 dV = (dV =)

Value
RSYN1.DifVClc.mag.f

Measured value

Absolute value

RSYN1.DifVClc.units.SIUnit

29

V (Volt)

RSYN1.DifVClc.units.multiplier

Kilo

Measured value

Absolute value

RSYN1. DifHzClc.units.SIUnit

33

Hz

RSYN1. DifHzClc.units.multiplier

Measured value

Absolute value

RSYN1. DifAngClc.units.SIUnit

(Degree)

RSYN1. DifAngClc.units.multiplier

RSYN1.DifHzCIc
No.

Information

170.2055 df = (df =)

Value
RSYN1. DifHzClc.mag.f

RSYN1.DifAngCIc
No.

Information

170.2056 dalpha = (d =)

116

Value
RSYN1. DifAngClc.mag.f

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.18 Three-pole tripping 52 Breaker (XCBR1)

2.18

Three-pole tripping 52 Breaker (XCBR1)

XCBR1.Mod
No.

Information

51

Device is Operational and Protecting (Device OK)

XCBR1.Mod.stVal
device annunciation:

1 0
1 5

1 - ON
0 - OFF

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

XCBR1.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

XCBR1.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF
x - irrelevant

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

XCBR1.Loc
No.
55

Information
Reset Device (Reset Device)

XCBR1.Loc.stVal
device annunciation:

1 0
1 0

1 - ON
0 - OFF

IEC Status Loc.stVal:

0 - FALSE
1 - TRUE

XCBR1.OpCnt
No.

Information
Number of TRIPs= (#of TRIPs=)

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Value
XCBR1.OpCnt.stVal

Metered value

Absolute value

117

Mapping
2.18 Three-pole tripping 52 Breaker (XCBR1)

XCBR1.Pos
No.

Information

4601

>52-a contact (OPEN, if bkr is open) (>52-a)

0 1 0 1

4602

>52-b contact (OPEN, if bkr is closed) (>52-b)

0 0 1 1

XCBR1.Pos.stVal - if spontan information

11 01 10 11

XCBR1.Pos.stVal - if command is running

00 01 10 00

device annunciation:

1 - ON
0 - OFF

IEC Status Pos.stVal:

00 - INTERMEDIATE STATE
01 - OFF
10 - ON
11 - BAD STATE

XCBR1.BlkOpn
No.
55

Information
Reset Device (Reset Device)

XCBR1.BlkOpn.stVal
device annunciation:

1 - ON
0 - OFF

1 0
0 1

IEC Status BlkOpn.stVal:

0 - FALSE
1 - TRUE

XCBR1.BlkCls
No.
55

Information
Reset Device (Reset Device)

XCBR1.BlkCls.stVal
device annunciation:

1 - ON
0 - OFF

1 0
0 1

IEC Status BlkCls.stVal:

0 - FALSE
1 - TRUE

XCBR1.CBOpCap
No.

Information

XCBR1.CBOpCap.stVal
device annunciation:

118

1
IEC Status CBOpCap.stVal:

1 - NONE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.18 Three-pole tripping 52 Breaker (XCBR1)

XCBR1.CirSpv
No.
6865

Information
74TC Failure Trip Circuit (74TC Trip cir.)

XCBR1.CirSpv.stVal
device annunciation:

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

0 1
0 1

IEC Status CirSpv.stVal:

0 - FALSE
1 - TRUE

119

Mapping
2.18 Three-pole tripping 52 Breaker (XCBR1)

XCBR1.SumSwARs1
No.
1021

Information

Value

XCBR1.SumSwARs1.actVal
Accumulation of
interrupted current Ph A
( Ia =)

Metered value

Current value of
acummulated interrupted
current = actVal pulsQty

XCBR1.SumSwARs1.units.SIUnit

A (Ampere)

XCBR1.SumSwARs1.units.multiplier

Kilo

1.000000e-002

A / Metered value

XCBR1.SumSwARs1.pulsQty

XCBR1.SumSwARs2
No.
1022

Information

Value

XCBR1.SumSwARs2.actVal
Accumulation of
interrupted current Ph B
( Ib =)

Metered value

Current value of
acummulated interrupted
current = actVal pulsQty

XCBR1.SumSwARs2.units.SIUnit

A (Ampere)

XCBR1.SumSwARs2.units.multiplier

Kilo

1.000000e-002

A / Metered value

XCBR1.SumSwARs2.pulsQty

XCBR1.SumSwARs3
No.
1023

Information

Value

XCBR1.SumSwARs3.actVal
Accumulation of
interrupted current Ph C
( Ic =)

Metered value

Current value of
acummulated interrupted
current = actVal pulsQty

XCBR1.SumSwARs3.units.SIUnit

A (Ampere)

XCBR1.SumSwARs3.units.multiplier

Kilo

1.000000e-002

A / Metered value

XCBR1.SumSwARs3.pulsQty

120

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.19 Tripping Logic of the Entire Device (PTRC1)

2.19

Tripping Logic of the Entire Device (PTRC1)

PTRC1.Mod
No.

Information

51

Device is Operational and Protecting (Device OK)

0 1 1

52

At Least 1 Protection Funct. is Active (ProtActive)

x 0 1

PTRC1.Mod.stVal
device annunciation:

5 5 1
1 - ON
0 - OFF

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTRC1.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

PTRC1.Health.stVal
device annunciation:

0 1
3 1

1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

PTRC1.Str
No.
501

Information
Relay PICKUP (Relay PICKUP)

PTRC1.Str.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

IEC Status Str.general:

0 - FALSE
1 - TRUE

121

Mapping
2.19 Tripping Logic of the Entire Device (PTRC1)

PTRC1.Tr
No.
511

Information
Relay GENERAL TRIP command (Relay TRIP)

PTRC1.Tr.general
device annunciation:

0 1
0 1

1 - ON
0 - OFF

IEC Status Tr.general:

0 - FALSE
1 - TRUE

PTRC1.FinTr
No.
2863

Information
79 - Lockout (79 Lockout)

0 1

PTRC1.FinTr.stVal
device annunciation:

122

0 1
1 - ON
0 - OFF

IEC Status FinTr.stVal:

0 - FALSE
1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.20 Measurement (MMXU1, MSQI1, MMTR1)

2.20

Measurement (MMXU1, MSQI1, MMTR1)

2.20.1

Measures (MMXU1)

MMXU1.Mod
No.

Information

51

Device is Operational and Protecting (Device OK)

MMXU1.Mod.stVal
device annunciation:

0 1
0 1

1 - ON
0 - OFF
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

MMXU1.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

MMXU1.Health.stVal
device annunciation:

1 - ON
0 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

0 1
3 1

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

123

Mapping
2.20 Measurement (MMXU1, MSQI1, MMTR1)

MMXU1.TotW
No.
641

Information
P (active power) (P =)

Value
MMXU1.TotW.mag.f

Measured value

Absolute value

MMXU1.TotW.units.SIUnit

62

W (Watt)

MMXU1.TotW.units.multiplier

Mega

Measured value

Absolute value

MMXU1.TotVAr.units.SIUnit

63

VAr

MMXU1.TotVAr.units.multiplier

Mega

Measured value

Absolute value

MMXU1.TotVA.units.SIUnit

61

VA

MMXU1.TotVA.units.multiplier

Mega

Measured value

Absolute value

MMXU1.TotPF.units.SIUnit

NONE

MMXU1.TotPF.units.multiplier

MMXU1.TotVAr
No.
642

Information
Q (reactive power) (Q =)

Value
MMXU1.TotVAr.mag.f

MMXU1.TotVA
No.
645

Information
S (apparent power) (S =)

Value
MMXU1.TotVA.mag.f

MMXU1.TotPF
No.
901

124

Information
Power Factor (PF =)

Value
MMXU1.TotPF.mag.f

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.20 Measurement (MMXU1, MSQI1, MMTR1)

MMXU1.Hz
No.
644

Information
Frequency (Freq=)

Value
MMXU1.Hz.mag.f

Measured value

Absolute value

MMXU1.Hz.units.SIUnit

33

Hz

MMXU1.Hz.units.multiplier

MMXU1.A.phsA.cVal.mag.f

Measured value

Absolute value

MMXU1.A.phsA.units.SIUnit

A (Ampere)

MMXU1.A.phsA.units.multiplier

MMXU1.A.phsB.cVal.mag.f

Measured value

Absolute value

MMXU1.A.phsB.units.SIUnit

A (Ampere)

MMXU1.A.phsB.units.multiplier

MMXU1.A.phsC.cVal.mag.f

Measured value

Absolute value

MMXU1.A.phsC.units.SIUnit

A (Ampere)

MMXU1.A.phsC.units.multiplier

MMXU1.A.neut.cVal.mag.f

Measured value

Absolute value

MMXU1.A.neut.units.SIUnit

A (Ampere)

MMXU1.A.neut.units.multiplier

MMXU1.A
No.
601

Information
Ia (Ia =)

No.
602

Information
Ib (Ib =)

No.
603

No.
604

Value

Value

Information
Ic (Ic =)

Value

Information
In (In =)

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Value

125

Mapping
2.20 Measurement (MMXU1, MSQI1, MMTR1)

MMXU1.PPV
No.
624

No.
625

No.
626

126

Information
Va-b (Va-b=)

Value
MMXU1.PPV.phsAB.cVal.mag.f

Measured value

Absolute value

MMXU1.PPV.phsAB.units.SIUnit

29

V (Volt)

MMXU1.PPV.phsAB.units.multiplier

Kilo

MMXU1.PPV.phsBC.cVal.mag.f

Measured value

Absolute value

MMXU1.PPV.phsBC.units.SIUnit

29

V (Volt)

MMXU1.PPV.phsBC.units.multiplier

Kilo

MMXU1.PPV.phsCA.cVal.mag.f

Measured value

Absolute value

MMXU1.PPV.phsCA.units.SIUnit

29

V (Volt)

MMXU1.PPV.phsCA.units.multiplier

Kilo

Information
Vb-c (Vb-c=)

Value

Information
Vc-a (Vc-a=)

Value

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.20 Measurement (MMXU1, MSQI1, MMTR1)

MMXU1.PhV
No.
621

No.
622

No.
623

No.
627

Information
Va (Va =)

Value
MMXU1.PhV.phsA.cVal.mag.f

Measured value

Absolute value

MMXU1.PhV.phsA.units.SIUnit

29

V (Volt)

MMXU1.PhV.phsA.units.multiplier

Kilo

MMXU1.PhV.phsB.cVal.mag.f

Measured value

Absolute value

MMXU1.PhV.phsB.units.SIUnit

29

V (Volt)

MMXU1.PhV.phsB.units.multiplier

Kilo

MMXU1.PhV.phsC.cVal.mag.f

Measured value

Absolute value

MMXU1.PhV.phsC.units.SIUnit

29

V (Volt)

MMXU1.PhV.phsC.units.multiplier

Kilo

MMXU1.PhV.neut.cVal.mag.f

Measured value

Absolute value

MMXU1.PhV.neut.units.SIUnit

29

V (Volt)

MMXU1.PhV.neut.units.multiplier

Kilo

Information
Vb (Vb =)

Value

Information
Vc (Vc =)

Value

Information
VN (VN =)

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Value

127

Mapping
2.20 Measurement (MMXU1, MSQI1, MMTR1)

2.20.2

Measured values, symmetrical components (MSQI1)

MSQI1.Mod
No.

Information

51

Device is Operational and Protecting (Device OK)

MSQI1.Mod.stVal
device annunciation:

0 1
0 1

1 - ON
0 - OFF
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

MSQI1.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

MSQI1.Health.stVal
device annunciation:

128

0 1
3 1

1 - ON
0 - OFF

IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.20 Measurement (MMXU1, MSQI1, MMTR1)

MSQI1.SeqA
No.

Information

605

I1 (positive sequence) (I1 =)

No.

Information

606

I2 (negative sequence) (I2 =)

No.
831

Value
MSQI1.SeqA.c1.cVal.mag.f

Measured value

Absolute value

MSQI1.SeqA.c1.units.SIUnit

A (Ampere)

MSQI1.SeqA.c1.units.multiplier

MSQI1.SeqA.c2.cVal.mag.f

Measured value

Absolute value

MSQI1.SeqA.c2.units.SIUnit

A (Ampere)

MSQI1.SeqA.c2.units.multiplier

MSQI1.SeqA.c3.cVal.mag.f

Measured value

Absolute value

MSQI1.SeqA.c3.units.SIUnit

A (Ampere)

MSQI1.SeqA.c3.units.multiplier

MSQI1.SeqV.c1.cVal.mag.f

Measured value

Absolute value

MSQI1.SeqV.c1.units.SIUnit

29

V (Volt)

MSQI1.SeqV.c1.units.multiplier

Kilo

Value

Information
3Io (zero sequence) (3Io =)

Value

MSQI1.SeqV
No.

Information

629

V1 (positive sequence) (V1 =)

No.
630

No.
832

Value

Information

Value

V2 (negative sequence) (V2 =) MSQI1.SeqV.c2.cVal.mag.f

Measured value

Absolute value

MSQI1.SeqV.c2.units.SIUnit

29

V (Volt)

MSQI1.SeqV.c2.units.multiplier

Kilo

Information
Vo (zero sequence) (Vo =)

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Value
MSQI1.SeqV.c3.cVal.mag.f

Measured value

Absolute value

MSQI1.SeqV.c3.units.SIUnit

29

V (Volt)

MSQI1.SeqV.c3.units.multiplier

Kilo

129

Mapping
2.20 Measurement (MMXU1, MSQI1, MMTR1)

2.20.3

Power Metering (MMTR1)

MMTR1.Mod
No.

Information

51

Device is Operational and Protecting (Device OK)

MMTR1.Mod.stVal
device annunciation:

0 1
0 1

1 - ON
0 - OFF
x - irrelevant

IEC Status Mod.stVal:

1 - ON
2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

MMTR1.Health
No.
51

Information
Device is Operational and Protecting (Device OK)

0 1

MMTR1.Health.stVal
device annunciation:

1 - ON
0 - OFF

3 1
IEC Status Health.stVal:

1 - OK
2 - WARNING
3 - ALARM

MMTR1.SupWh
No.
924

Information

Value

Wp Forward (Wp+=) MMTR1.SupWh.actVal

Metered value

Current value of acummulated


interrupted current =
actVal pulsQty

MMTR1.SupWh.units.SIUnit

72

Wh

MMTR1.SupWh.units.multiplier

Mega

3.464200e-005

Wh / Metered value

MMTR1.SupWh.pulsQty

130

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Mapping
2.20 Measurement (MMXU1, MSQI1, MMTR1)

MMTR1.SupVArh
No.
925

Information

Value

Wq Forward (Wq+=) MMTR1.SupVArh.actVal

Metered value

Current value of acummulated


interrupted current =
actVal pulsQty

MMTR1.SupVArh.units.SIUnit

73

VArh

MMTR1.SupVArh.units.multiplier

Mega

3.464200e-005

VArh / Metered value

MMTR1.SupVArh.pulsQty

MMTR1.DmdWh
No.

Information

928

Wp Reverse (Wp-=)

Value
MMTR1.DmdWh.actVal

Metered value

Current value of acummulated


interrupted current =
actVal pulsQty

MMTR1.DmdWh.units.SIUnit

72

Wh

MMTR1.DmdWh.units.multiplier

Mega

3.464200e-005

Wh / Metered value

MMTR1.DmdWh.pulsQty

MMTR1.DmdVArh
No.

Information

929

Wq Reverse (Wq-=)

Value
MMTR1.DmdVArh.actVal

Metered value

Current value of acummulated


interrupted current =
actVal pulsQty

MMTR1.DmdVArh.units.SIUnit

73

VArh

MMTR1.DmdVArh.units.multiplier

Mega

3.464200e-005

VArh / Metered value

MMTR1.DmdVArh.pulsQty

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

131

Mapping
2.20 Measurement (MMXU1, MSQI1, MMTR1)

132

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Literature

Literature
/1/

SIPROTEC 4 System Description


E50417-H1176-C151

/2/

SIPROTEC DIGSI, StartUP


E50417-G1176-C152

/3/

DIGSI CFC, Manual


E50417-H1176-C098

/4/

SIPROTEC SIGRA 4, Manual


E50417-H1176-C1100-C070

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

133

Literature

134

SIPROTEC, 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Index
C
CALH1 10, 19, 29
ErrBoard1 30
ErrBoard2 30
ErrBoard3 30
ErrBoard4 30
ErrBoard5 31
ErrBoard6 31
ErrBoard7 31
GrAlm 29
GrWrn 29
Health 29
Mod 29

D
DOI 9
F
Function parameters 10
Functional Scope
7SJ66 11

L
LD
CTRL (Control) 10, 19
DR (Disturbance Recorder) 18
EXT (Extended) 19
Logical Device 8
MEAS (Measurement) 10, 18
PROT (Protection) 10, 16
LLN0 8, 10, 16, 18, 19
Beh 20, 22, 23
Health 20, 22, 23
Mod 22, 23
OpTmh 21, 24
Logical Node 9, 11, 16
LPHD1 8, 10, 17, 18, 19, 28
DevStr 28
PhyHealth 28
Proxy 28

M
MMTR1 10, 18, 130
DmdVArh 131
DmdWh 131
Health 130
Mod 130
SupVArh 131
SupWh 130
MMXU1 10, 18, 123
A 125, 128
Health 123
Hz 125
Mod 123
PhV 127

PPV 126
TotPF 124
TotW 124
TotVA 124
TotVAr 124
MSQI1 10, 18, 128
Health 128
Mod 128
SeqA 129
SeqV 129

P
PHIZ1 13, 17, 98
Health 98
Mod 98
Op 102
Str.dirGeneral 99
Str.dirPhsA 100
Str.dirPhsB 101
Str.dirPhsC 102
Str.general 98
Str.phsA 99
Str.phsB 100
Str.phsC 101
PMLJ1 14, 17, 77
Health 77
LodJamAlm 78
Mod 77
Op 78
Str 78
PMRI1 14, 17, 76
Health 76
Mod 76
Op 76
StrInhTmm 76
PMSS1 13, 17, 74
Health 74
Mod 74
Op 75
Str 75
PSDE1 13, 17, 103
Health 103
Mod 103
Op 104
Str.dirGeneral 104
Str.general 103
PSDE2 13, 17, 104
Health 104
Mod 104
Op 105
Str.dirGeneral 105
Str.general 105
PSDE3 13, 17, 106
Health 106

135
SIPROTEC, SIPROTEC 7SJ66, IEC61850 MAPPING
C53000-L2640-C554-1, Edition 03.2014

Mod 106
Op 107
Str.dirGeneral 107
Str.general 106
PTOC1 11, 16, 37
ChgSet 38
Health 38
Mod 37
Op 38
Str 38
PTOC10 12, 16, 46
ChgSet 47
Health 46
Mod 46
Op 47
Str 46
PTOC11 12, 16, 47, 48
ChgSet 48
Health 47
Mod 47
Op 48
Str 48
PTOC12 12, 16, 52
ChgSet 53
Health 52
Mod 52
Op 52
Str 52
PTOC13 12, 16, 53, 54
ChgSet 54
Health 53
Mod 53
Op 54
Str 53
PTOC14 13, 17, 70
Health 70
Mod 70
Op 70
Str 70
PTOC15 13, 17, 71
Health 71
Mod 71
Op 71
Str 71
PTOC16 13, 16, 61
Health 61
Mod 61
Op 61
Str 61
PTOC17 13, 16, 62
Health 62
Mod 62
Op 63
Str 63
PTOC18 11, 16
Health 36
Mod 36
Op 37

SIPROTEC, SIPROTEC 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

Str 37
PTOC19 12, 16
ChgSet 49
Health 49
Mod 48
Op 49
Str 49
PTOC2 11, 16, 41
ChgSet 42
Health 41
Mod 41
Op 42
Str 42
PTOC20 12, 16
ChgSet 55
Health 54
Mod 54
Op 55
Str 55
PTOC3 12, 16, 50
ChgSet 51
Health 50
Mod 50
Op 50
Str 50
PTOC4 12, 16, 55
ChgSet 56
Health 56
Mod 55
Op 56
Str 56
PTOC5 13, 17, 72
Health 72
Mod 72
Op 73
Str 73
PTOC6 11, 16, 34
ChgSet 35
Health 34
Mod 34
Op 34
Str 34
PTOC7 11, 16, 35
ChgSet 36
Health 35
Mod 35
Op 36
Str 35
PTOC8 11, 16
ChgSet 40
Health 39
Mod 39
Op 39
Str 39
PTOC9 11, 16, 40
ChgSet 41
Health 40
Mod 40

136

Op 41
Str 40
PTOF1 14, 17, 87
BlkV 88
Health 87
Mod 87, 89
Op 88
Str 88
PTOF2 89
BlkV 90
Health 89
Mod 89
Op 90
Str 90
PTOF3 91
BlkV 92
Health 91
Mod 91
Op 92
Str 92
PTOF4 93
BlkV 94
Health 93
Mod 93
Op 94
Str 94
PTOV1 14, 16, 68
Health 68
Mod 68
Op 68
Str 68
PTOV2 14, 69
Health 69
Mod 69
Op 69
Str 69
PTRC1 10, 16, 121
FinTr 122
Health 121
Mod 121
Str 121
Tr 122
PTRC2 11, 16, 43
Health 43
Mod 39, 43
Op 39, 45
Str 43
Str.dirGeneral 43
Str.dirNeut 45
Str.dirPhsA 44
Str.dirPhsB 44
Str.dirPhsC 45
Str.neut 45, 60
Str.phsA 44
Str.phsB 44, 45, 59, 60
Str.phsC 44, 45, 59, 60
PTRC3 12, 16, 57
Health 57
Mod 57

Op 60
Str 57
Str.dirGeneral 58
Str.dirNeut 60
Str.dirPhsA 58
Str.dirPhsB 59
Str.dirPhsC 59
Str.neut 60
Str.phsA 58
Str.phsB 59
Str.phsC 59
PTTR1 14, 17, 96
AlmThm 97
Health 96
Mod 96
Str 96
Tr 97
PTUF1 14, 17, 79
BlkV 80
Health 79
Mod 79
Op 80
Str 80
PTUF2 81
BlkV 82
Health 81
Mod 81
Op 82
Str 82
PTUF3 83
BlkV 84
Health 83
Mod 83
Op 84
Str 84
PTUF4 85
BlkV 86
Health 85
Mod 85
Op 86
Str 86
PTUV1 14, 16, 64, 95
Health 64
Mod 64
Op 65
Str 65
PTUV2 14, 66
Health 66
Mod 66
Op 67
Str 67
PTUV7 17
Health 95
Mod 95
Op 95
Str 95
PVOC1
Mod 39, 45

137
SIPROTEC, SIPROTEC 7SJ66, IEC61850 MAPPING
C53000-L2640-C554-1, Edition 03.2014

R
RBRF1 14, 17, 112
Health 112
Mod 112
OpEx 113
OpIn 113
Str 112
RDRE1 11, 18, 32
FltNum 33
GriFltNum 33
Health 32
Mod 32
RcdMade 32, 33
RcdStr 33
RFLO1 14, 17, 110
FltDiskm 111
FltDisPrc 111
FltZ 111
Health 110
Mod 110
RREC1 14, 17, 108
AutoRecSt 109
Health 108
Mod 108
Op 109
RSYN1 14, 19, 114
AngInd 115
DifAngCIc 116
DifHzCIc 116
DifVCIc 116
Health 114
HzInd 115
Mod 114
Rel 114
SynPrg 115
VInd 115
RSYN2
DifAngCIc 116
DifVCIc 116
Health 116
RSYN3
DifVCIc 116
RSYN4
HzInd 117

SumSwARs2 120
SumSwARs3 120

X
XCBR1 10, 16, 117
BlkCls 118
BlkOpn 118
CBOpCap 118
CirSpv 119
Health 117
Loc 117
Mod 117
OpCnt 117
Pos 118
SumSwARs1 120

SIPROTEC, SIPROTEC 7SJ66, IEC61850 MAPPING


C53000-L2640-C554-1, Edition 03.2014

138

Anda mungkin juga menyukai