2N3055
2N3904
2N3906
Vs= +/-16v
Rl=8
Po=30W (d=0.5%)
TDA2003 has improved performance with the same pin configuration as the
TDA 2002. The features of TDA 2002 - very low number of external
components, ease of assembly, space and cost saving - are maintained.
The device provides a high output current capability (max. 3.5A), very low
harmonic and cross-over distortion. A completely safe operation is guaranteed
due to protection against DC and AC short circuit between all pins and ground,
thermal over-range, load dump voltage surge up to 40V and fortuitous open
ground.
The combination of the LM4651 driver IC and the LM4652 power MOSFET Class D power amplifier IC provides a high efficiency amplifier solution,
suitable for self-powered speakers, subwoofers and quality car boosters.
The LM 4651 is a fully integrated conventional pulse width modulator (PWM) driver, containing undervoltage, short circuit, overmodulation, and thermal
shutdown protection circuitry. The IC features a standby function which shuts down the pulse width modulation, minimizing supply current.
The LM 4652 is a fully integrated H-bridge Power Mosfet IC in a TO220 power package. The IC has a built in temperature sensor to alert the LM4651
when the die temperature exceeds the threshold limit.
Used together, the LM4651 and LM4652 form a simple, compact, efficient, high quality power audio amplifier solution complete with protection, normally
seen only in Class AB amplifiers.
The maximum efficiency of this circuit is 85% at 125W with a standby attenuation greater than 100dB. The THD at 10W, 4 ohms, 10 - 500Hz is max.
0.3%. The supply voltage can not exceed 22V.
For the best performance a suitable preamplifier is required. With the addition of a preamplifier the gain of the power stage can be greatly reduced to
improve performance. The gain should be set to 10 V/V allowing for low gain on the Class D stage with a total system gain high enough to be a
complete solution for line level sources.
The input filter used here does not noticeably increase THD performance but will help to maintain a flat frequency response as the Q of the output filter
changes with load impedance.
Design notes, full specs and recommended PCB reference designs can be found here.
Do not attempt to build this amplifier as your first project! Class D high power amplifiers are expensive, difficult to build and a very small error during
assembly can lead to total devastation of the power IC or other costly components.
Parameter
Value
Vs
18 V
Vs
DC Supply Voltage
28 V
Vs
40 V
Io
Io
3.5 A
Ptot
30 W
Tstg, Tj
-40 to 150C
The Tda2005 IC has a high output power: PO=10W+10W @ RL=2ohm, d=10% (stereo) and PO=20W @ RL=4ohm, d=1% (bridge) for Vs=14.4V. The
high reliability of the IC comes from the various protections against: output DC and AC short circuit to ground, overrating chip temperature, load dump
voltage surge, fortuitous open ground and very inductive loads.
The IC can be used used in bridge (TDA2005M) or stereo (TDA2005S) amplifiers - with or without boostrap - with easily programmable gain and
bandwidth. The Tda2005 needs a very low number of external components, and has a very simple mounting system with no electrical isolation between
the package and heatsink.
12V- 1.2A
TDA2030 14w
12V- 1.4
TDA2040 25w
24V- 1.5A
TDA2050 32w
24V- 2A
Los C.I. anteriores todos son MONOAURALES y que para Estreo se tendr que armar
la etapa 2 veces y habr el doble de consumo de corriente.
Paso 1: Como todos estos circuitos integrados tienen las mismas conexiones, se
realizar el impreso identificando los siguientes terminales:
Fig 2: 20W Bridge Amplifier Circuit with TDA2005M (Voltage Gain = 34dB)
Hola para probar con estos niveles de potencia debes tener cierta experiencia y
entendimiento sobre lo que estas haciendo pues hay en juego altos niveles de
tension 130V y corrientes de unos 5A por canal.
Ten encuenta tambien que dependiendo del tipo de amplificador los rendimientos no
suelen superar un 65% de la potencia que consumen.
Con esto te quiero decir que por ej. para obtener 65 watts vas a necesitar un trafo
(fuente) de 100W para tener un buen sonido con distorcion minimizada.
Los filtros de la fuente mas que grandes te recomiendo que sean muchos.
Por ejemplo un circuito de la fisma sanyo que entrega unos 160W es el STK4048.
Hay varias versiones que son mejoras de la anterior; por ejemplo el STK4048V es
mejor que el STK4048II.
del
filtrado de la fuente. 43*1.3= 55.9V