0 2
02.1.
Taller 02
| P L A N T A A L T A
COPIAR
1 Abra el dibujo de
la planta baja. 01
2 Copie el dibujo de
la planta baja y
ubíquelo sobre ésta
(Figura 01).
FIGURA 03:
Línea auxiliar.
27
TALLER AUTOCAD
FIGURA 04:
Línea paralela.
05
FIGURA 05:
Utilización de Offset (Equidistante).
FIGURA 06:
04
Utilización de los comandos Extend
(Extensión) y Trim (Recortar).
FIGURA 07:
Espejado del baño.
Command: _offset
Specify offset distance or [Through] <Through>: 0.20
ENTER 06
a
nea continua y utilizando los comandos Ex-
tend (Extensión) y Trim (Recortar) haga las
terminaciones de las líneas recién construidas.
Command: _mirror
Select objects: Specify opposite corner: 7 found
ENTER
Select objects:
07
Specify first point of mirror line: _nea to
Specify second point of mirror line: _nea to
Delete source objects? [Yes/No] <N>:
b
ENTER
28
TALLER 02 • PLANTA ALTA
a 08
FIGURA 08:
Construcción del arco.
FIGURA 09:
Espesor del arco.
b 09
c Command: _extend
Current settings: Projection=UCS Edge=None
Select boundary edges ...
ENTER
Select objects:
ENTER
Select object to extend or [Project/Edge/Undo]:
Select object to extend or [Project/Edge/Undo]:
Select object to extend or [Project/Edge/Undo]:
ENTER
29
a
TALLER AUTOCAD
FIGURA 10:
Construcción de espacio.
FIGURA 11:
Desplazamiento.
FIGURA 12:
Extensión de líneas.
12
10
11
b
Select objects:
Specify base point or displacement: _endp of
Specify second point of displacement or <use first point as
displacement>: _from Base point: _per to
<Offset>: @0,-0.30
ENTER
c ** STRETCH **
Specify stretch point or [Base point/Copy/Undo/eXit]:
_endp of
30
TALLER 02 • PLANTA ALTA
Desplazamiento
FIGURA 13: Cierre del dibujo
a
d
b
e
c
f
14 Construya y cierre el dibujo en la parte
izquierda de la sección de abajo.
Command: _mirror
Select objects: 1 found
Command: _stretch Select objects: 1 found, 2 total
Select objects to stretch by crossing-window Select objects:
or crossing-polygon...
Specify first point of mirror line: _mid of
Select objects: Specify opposite corner: 4 found
Select objects: Specify second point of mirror line: _per to
Specify base point or displacement: Delete source objects? [Yes/No] <N>:
Specify second point of displacement: @0,-0.1 ENTER ENTER
31
TALLER AUTOCAD
a d
b e
c f
15 Desplace la sección opuesta (arriba, si-
métrica) hacia arriba y borre la pared
del medio (Figura 14).
Command: _move
Select objects:
Specify opposite corner: 5 found
Select objects:
Command: _move
Specify base point or displacement: _endp of
Select objects: 1 found
Specify second point of displacement or <use first point as
Select objects: 1 found, 2 total
Select objects: 1 found, 3 total displacement>: _endp of
Select objects:
Specify base point or displacement: _endp of Command: _extend
Specify second point of displacement or <use first point as Current settings: Projection=UCS Edge=None
displacement>: @0,0.20 ENTER
Select boundary edges ...
Select objects:
ENTER
Command: _erase
Select object to extend or [Project/Edge/Undo]:
Select objects: 1 found
Select objects: 1 found, 2 total Select object to extend or [Project/Edge/Undo]:
Select objects: 1 found, 3 total Select object to extend or [Project/Edge/Undo]:
Select objects: 1 found, 4 total Select object to extend or [Project/Edge/Undo]:
Select objects: ENTER ENTER
32
TALLER 02 • PLANTA ALTA
a d
b e
c f
16 Desplace la pared de abajo del Placard
enfrentada a éste último, y extiéndala.
f
Select objects: Specify opposite corner: 3 found
Select objects:
Specify base point or displacement: _endp of
Command: _stretch Specify second point of displacement: _from Base point:
Select objects to stretch by crossing-window or crossing- _endp of <Offset>: @-0.65,0 ENTER
polygon...
Select objects:
Specify opposite corner: 5 found
Select objects:
Specify base point or displacement: _endp of
17 Desde la abertura de abajo dibuje con el
comando Rectangle (Rectángulo) el espacio
para una ventana.
Specify second point of displacement: _from Base point:
_endp of <Offset>: @0,0.6 ENTER
Command: _rectang
Specify first corner point or [Chamfer/Elevation/Fillet/Thick-
Command: _stretch ness/Width]: _from Base point: _endp of <Offset>:
Select objects to stretch by crossing-window or crossing- @1.225,0 ENTER
polygon... Specify other corner point: @1.20,-0.30 ENTER
f
33
TALLER AUTOCAD
FIGURA 16:
a
Dibujo del espacio de la ventana.
FIGURA 17:
Construcción de la escalera en la
planta alta.
16
a
FIGURA 18:
Construcción del conducto de humos
de la chimenea.
b
18 Haga un zoom en la sección de la escale-
ra y el pasillo.
b
Command: _extend
Current settings: Projection=UCS Edge=None
Select boundary edges ...
Select objects: ENTER
Select object to extend or [Project/Edge/Undo]:
Select object to extend or [Project/Edge/Undo]:
Select object to extend or [Project/Edge/Undo]: ENTER
17
Command:
Command: _trim
Current settings: Projection=UCS Edge=None
Select cutting edges ...
Select objects: 1 found
Select objects:
Select object to trim or [Project/Edge/Undo]:
Select object to trim or [Project/Edge/Undo]: ENTER
Command: _extend
c
Current settings: Projection=UCS Edge=None
Command: _offset
Select boundary edges ...
Specify offset distance or [Through] <0.0500>: 0.20
Select objects: 1 found
ENTER
Select objects:
Select object to offset or <exit>:
Select object to extend or [Project/Edge/Undo]:
Specify point on side to offset:
Select object to extend or [Project/Edge/Undo]:
Select object to offset or <exit>: ENTER
ENTER
34
Conductos TALLER 02 • PLANTA ALTA
a
d
18
b e
Command: _line
Specify first point: _mid of
Specify next point or [Undo]: _per to
Specify next point or [Undo]:
ENTER
35
TALLER AUTOCAD
a FIGURA 21:
Dibujo de parantes
a
del ventanal.
19
b
21 Haga un zoom en la parte trasera de la
casa y borre los espesores de la pared y
las ventanas (trasera y lateral)
21
Command: _erase
Select objects: 1 found
Select objects: 1 found, 2 total
Select objects: 1 found, 3 total
Select objects: 1 found, 4 total
b
Select objects: 1 found, 5 total
Select objects: 1 found, 6 total
Select objects: 1 found, 7 total
Select objects: 1 found, 8 total ENTER
Command: _rectang
Specify first corner point or [Chamfer/Elevation/Fillet/Thick-
ness/Width]: _endp of
Specify other corner point: @0.08,-0.0250 ENTER
36
c
Ventanas
TALLER 02 • PLANTA ALTA
a
a
b 23
22
b
Command: _array Command: _rectang
Select objects: 1 found Specify first corner point or [Chamfer/Elevation/Fillet/Thick-
Select objects: ness/Width]:
Enter the type of array [Rectangular/Polar] <R>: r Specify other corner point: @0.08,0.9 ENTER
ENTER
Enter the number of rows (—-) <1>: 8
ENTER Command: _block
Enter the number of columns (|||) <1> 1 Select objects: Specify opposite corner: 1 found
ENTER Select objects: Specify insertion base point:
Enter the distance between rows or specify unit cell (—-): -
0.825
ENTER Command: _insert
Specify insertion point or [Scale/X/Y/Z/Rotate/PSca-
le/PX/PY/PZ/PRotate]:
Specify rotation angle <0>:
23 Cambie al layer aberturas.
Command: _rectang
Specify first corner point or [Chamfer/Elevation/Fillet/Thick-
24 Elimine todas las puertas y en su lugar
dibuje una ventana de 0.90, 0.08 mtrs. y
otra para la parte trasera de 0.8, 0.08 met-
ness/Width]: _from Base point: _endp of <Offset>: @0,-
0.20 ENTER
ros. Luego conviértalas en bloque. Specify other corner point: @-0.08,-0.6 ENTER
37
TALLER AUTOCAD
a ventanales
P
24
FIGURA 24:
c
b
Construcción de los ventanales traseros.
Command:
INSERT
Specify insertion point or [Scale/X/Y/Z/Rotate/PSca-
le/PX/PY/PZ/PRotate]: _endp of
Command:
INSERT
Specify insertion point or [Scale/X/Y/Z/Rotate/PSca-
Command: _rectang le/PX/PY/PZ/PRotate]: _endp of
Specify first corner point or [Chamfer/Elevation/Fillet/Thick- Command:
ness/Width]: _endp of INSERT
Specify other corner point: @0.08,0.8 ENTER Specify insertion point or [Scale/X/Y/Z/Rotate/PSca-
le/PX/PY/PZ/PRotate]: _endp of
ENTER
Command: _block
Select objects: 1 found
Select objects:
Specify insertion base point: _endp of 25 Introduzca los bloques de las puertas
construidas en la planta baja en la en-
trada del baño, y para los dormitorios cons-
truya una de 0.08, 0.70 metros.
Command: _insert
Specify insertion point or [Scale/X/Y/Z/Rotate/PSca-
le/PX/PY/PZ/PRotate]: _endp of Command: _rectang
Command: INSERT Specify first corner point or [Chamfer/Elevation/Fillet/Thick-
Specify insertion point or [Scale/X/Y/Z/Rotate/PSca- ness/Width]: _from Base point: _endp of <Offset>:
le/PX/PY/PZ/PRotate]: _endp of @0.08,0 ENTER
Command: INSERT Specify other corner point: @0.70,0.08 ENTER
Specify insertion point or [Scale/X/Y/Z/Rotate/PSca-
le/PX/PY/PZ/PRotate]: _endp of
Command: INSERT Command: _arc
Specify insertion point or [Scale/X/Y/Z/Rotate/PSca- Specify start point of arc or [CEnter]: _endp of
le/PX/PY/PZ/PRotate]: _endp of Specify second point of arc or [CEnter/ENd]: e
Command: ENTER
INSERT Specify end point of arc: _endp of
Specify insertion point or [Scale/X/Y/Z/Rotate/PSca- Specify center point of arc or [Angle/Direction/Radius]: d
le/PX/PY/PZ/PRotate]: _endp of ENTER
Specify tangent direction for the start point of arc: <Ortho on>
38
Puertas FIGURA 25: Construcción de puertas
TALLER 02 • PLANTA ALTA
a d
25
b e
c f
Command: _block FIGURA 26: Dibujo de ventana
Select objects: 1 found
Select objects: 1 found, 2 total
Select objects: Specify insertion base point:
Command: _rectang
Specify first corner point or [Chamfer/Elevation/Fillet/Thick-
ness/Width]: _endp of
Specify other corner point: @1.2,-0.10 ENTER
39
TALLER AUTOCAD
27 FIGURA 27:
Contorno del garage.
FIGURA 28:
Construcción de ventanal curvo.
a
Command: _offset
Specify offset distance or [Through] <0.0300>: 0.05
ENTER
Select object to offset or <exit>:
Specify point on side to offset:
Select object to offset or <exit>:
ENTER
40