Page
Types of Generators 1
Permanent Magnet Machines 1
Rotating Armature Type 1
Rotating Field Type 4
Connection of Phases 7
Power in 3 Phase Systems 9
Frequency Wild Systems 10
Brushless Generators 13
Volt-a-geegulation
i
. 16 .-.
\, 16 , -, , '.> ,.
1'/r'ransistorised Voltage B&iylatoS 17 IIm ,i i ., ,
',
\,
C o n s t v t Frequency Systemqi I
, ! I '
; ; 19 : :j
j CSDU in a on-~arallegeh Systek
! : 1' i
i
20
2.3
I i I
i
I
I Indications / L-
./
,/
8 . /
,
/'
on-~balleled
, ,
Systems
i
-
--1
I.,
26 \
!
i
--//
-1'
/:
1I Fault Protection \,,, ',.~,,'.
, 29 i
i M ~ ~ U ~ ; FTripping
CR ! i 33
! !
I
!.
:
I,
~ o d i ~ h e d d i n :~ 1 ,i ,/ 36
i
,I
'
,
',-
f'
L
g-j~' 1, !
.------I
_ - ,-' 39
/'
I
7-'
-
; 1~
L -
I i
I i
I
rotates
acoutput -- -'
from stationary
windings I ,
I i
SINGLE PHASE
ARMATURE
WINDING
BRUSHES
One cycle of voltage is induced when the conductor moves through 360"
past one pair of poles. If there are two pairs of poles then two cycles of ac
will be produced.
- 2-
rnoodull l A-740
f = Np
60 Hertz
An ac I
I Cenerator, in which theI who_lc ofthe
,
---I /
- ' /
I
FIELD COILS
CWINDMG AT 0°1
SLIP RINGS
PHASE C
(WINLIING AT 240"
-3-
rnoodull l A-741
Figure 4 shows a three phase system, in which the coils are at 120"to
each other and a 3 phase output is generated. In other words it is really 3
generators in one with 3 separate outputs each one 120" out-of-phase
with the next.
,'
Fig. 5 CURVE YF-INDUCED EMF - 3 PHASE -
1 1
' 1
I
1
I
I
I
II
I (a) As all the power is taken from the rotor, the efgective
insulation and v'eritilation causes problems.
- - -
(b) All the (heavy) output is taken via slip-rings and brushes.
-
I n this type of generator the dc field rotates and its field cuts the
stationery (output) windings on the stator. The output windings consist of
a number of coils connected in series and inserted in slots in the
laminated stator to give a single phase output. The field windings are
supplied with dc via two slip rings and brushes.
STATOR WINDINGS
I
ac OUTPUT
dc INPUT
.-
DRIVE
SHAFT
ROLLERM
RACE
I
i', , FIELD WINDINGS ROTOR I
I
1 , I 1 , I
/ Fig. 7 SEC'~'I,ONO$;R~TATING FIELD(
I SINGLE~P~ASE ~ C ~ E N E R A T O;
R' -;
_I - I
If another set of single phase windings at 90" to the first set is added, then
a two phase output i s produced being 90" out-of-phase with the first
(figures 8 and 9).
If afurther set of two coils is added and each coil in the system is spaced
a t 60" to each other then we have a three phase system. Each pair of coils
is-spaced a t 120" to one angther so there are 3 phases where the 3
outputs are 120" out of phase YfigUre\lO). I
I
I
The advantages of the rotating field generator over the rotating armature
type are:
(a) Only two slip-rings and brushes are used taking less current, ie
field winding current only.
(b) Less problems with centrifugal effects on rotor windings.
(c) The output is taken from the stator, where ventilation and
insulation of windings is less of a problem.
Connection of Phases
This shows that the three windings are connected to one point and a lead
is taken from that point. This configuration is called STAR CONNECTION
and the point where they meet is called the star point a n d the lead taken
from the star point i s called the neutral lead.
l line
! I
I
/ ; ~: ! 1
, I
!
j
I
1
i _ - - l
' i
" ', Fig. 11 STAR CONNI$CTION
i GENERAT&
,,
.'
/
L-~-_-'
, L
l.?-l-:
-1
-- // i. .
.--I .
The phase voltage (Vphase)on an aircraft generator would be 1 15V and the
line voltage (Vs,,) which is the sum of the two phase voltages across that
line, ie two 115V phases a t 120' phase angle, is 200V a n d mathematically
is the same as multiplying the phase voltage by 43.
The big advantage of the star connection is that with the neutral line two
voltages are available - 200 and 115. Aircraft ac generators are generally
connected in star.
l phase
Vphase V line
l llne
l phase
-
B
-
l line
L t 1
-
L>
! t' f
I
\
\\
\
- -
\
\
I ' i / I
1I 1' I I
1 = d3~~1~cos0watts II -- , I
I 1
I
-7
\, \' I -- --/
/
1
1
\ i ' 1
For a kelta cqnnected s y s t e 4 VL= Vph
:,
I
I '
/
I '
1
'Then dhe fornula can be w r i t t e h L - - -
--- -- - - - 1 --- / ' --2
True Power = ~ V L I ~ ~0Cwatts
OS
and as IL = d 3 1 ~
So for star or delta connected systems there are two formulas for power.
At this time electrical heater mats for de-icing had created the need for
large quantities of power. A s these elements are resistive, the variation of
frequency had no effect, so the frequency wild constant voltage supply was
fed to resistive circuits such as windshield heating, heater mats on the
-
airframe, engine de-icing heaters etc. ' 1 I
I I
AC GENERATOR (CONSTANT
VOLTAGE FREQUENCY WILD)
DIRECTLY CONNECTED TO
ENGINE GEAR BOX
f TRU
CONTACTOR
TRU
DC BUS
- 4 6 . 2
111 = *
"r"
'
111 TO DC SERVICES
OUTPUT FREQUENCY
PROPORTIONAL
TO GENERATOR rpm
VOLTAGE
REGULATOR I\-
-
d
DC TO ROTATING FIELD
The TRU transforms the ac voltage
down to 28V and then rectifies it to dc
- 10 -
rnoodull I A-748
104V
OUTPUT
EXCITATION
WINDING
This generator is of the rotating field type. A s can be seen from the
intEnd-circuit diagram it hzsmO stator windings, one1prodming 208V
and'thg other 104V. The speed-r%Z~2,i$3,300rprn to 1O:lOEpin giying a
range of 165Hz to s05Hz. ~he'\rotor winding id supplied with
via two slip-qngs. 1 I I I
1
I
'
i
/
I,
' ,i
I !I
m-
112V DC
TO MIC (28V)
BUS +VE
The supply from the 208V winding is fed via the compounding TKU to the
frequency-wild services. From terminal A1 of the Main Control Unit a
supply is fed back to the rotor winding to maintain the voltage constant.
OUTPUT PROTECTION
TERldINAL BOX I7UNSPORHgR
ROTOR \ /
STATOR
I
COOLING A I R
BALL RACE
Durn
*kVA is a term used to denote the power output from a generator and is
kilo Volts Amps. (From module 3 volts x amps = watts. Not strictly true for
generator outputs but the two can be equated as a very simple rule).
BRUSHLESS GENERATORS
There are many types of brushless ac generators in use, we shall deal with
two variations on the theme.
--
GENERATOR
" " ....-
4
- ROTOR
WN ROTATING
ROTATING
...
FIELDr
TRANSFPRMERL
With reference to figure 18. There are two main parts in its construction:
Operation
- 13 -
rnoodull l A-751
(b) Silicon diodes located on the rotor form a 3 phase, full-wave rectifier
bridge, converting the output into dc, which is smoothed by a
capacitor and fed along the rotor to the rotating field poles of the
main generator.
(c) The rotating field induces emf's into the main 3 phase stationary
output windings which are star-connected (externally in this case) to
give phase voltages of 1 15V rms and line-to-line voltages a t 2 0 0 V
rms.
(d) Apart from feeding out to the loads, the generator output is fed
back, via a voltage regulator, a s dc onto its own exciter field
windings. The exciter field windings take over from the permanent
magnets in controlling the output voltage of the generator. (In this
machine, the permanent magnets play n o further part in the
operation a s their flux densities are low compared to that of the
exciter field coils).
(e) Two field windings are provided for the exciter. One ( F l ) is
I-
permanently in circuit. The-second (F2) is only brought-into
operation in the event of a temperature rise causing the resistance
of F1 to increase to the point where the voltage regulator is unable
to sustain sufficient current through it to maintain the voltage.
(This is known as ~ i e l dCritical Resistance). As thk temperature
rises the thermistor rebistance decreases and allows current-
to flow
' through F2, so assisting F 1. I
1 1
(g) The current transformer boost circuit assists the voltage regulator
during load changes and during periods of large unbalanced loads
on the generator.
- 14 -
moodull l A-752
(b) The Main Exciter, which is a Rotating Armature, Star-wound
ac generator.
3 PHASE 1151MOV
4(#3 Hz ac OUTPUT
TO 3 SEPARATE
ROTATING FIELD
EXCITER
The regulator section controls and rectifies this output and feeds a dc
current to the main stationary exciter winding. This is controlled to keep
the generator voltage output constant irrespective of load. This dc field is
cut by the rotating star connected exciter armature winding which
induces a n ac into it. This ac is fed via the six diodes on the rotating
armature to give 3 phase full wave rectification and therefore dc to the
main field coil (also being rotated by the engine). This rotating field c u t s
the star connected windings of the main generator to give 1 15/200V 3
phase 400Hz output (400Hz provided the generator is rotating a t the
required rpm).
Part of the output is fed back to the voltage regulator in the GCU which
controls the dc to the exciter field-and hence the generator output.
1
VOLTAGE REGULATION ,
,>
' ',
I
Incrcaked line~uoltage(cause increased speed or reduction in load)
/
cau$es an increased dc voltage to be to the error sensing bridge.
DUX' td-the-tion of the conskant_voltag~lubes, point A now becomes
i-
pdsitive-with-iespect to point-B and-euirent flows through-th2 control
winding from A to B. This h a s the effect of reducing the current in the
exciter field a n d so reducing the generator output voltage back to normal.
The output from the PMG (figure 22) is fed to the star connected primary
of a transformer in the GCU. The star connected secondary of the
transformer feeds a combined voltage regulator and Transformer Rectifier
Unit (TRU) to ensure the voltage to the field circuit is a constant dc
voltage.
G E N E R A T O R OUlPUT
-
i I
Fig. 22 TRANSISTORISED VOLTAGE REGULATION
I '
I
NORMAL GEN VOLTAGE LOW GEN VOLTAGE HIGH GEN VOLTAGE TIME
(NORMAL LOADING) (HIGH LOAD) (LOW LOAD)
- 18-
rnoodull l A-756
If the generator loading was to increase, the terminal voltage of the
generator would decrease (due to internal voltage drop), this would be
sensed by the regulator which would signal the switching transistor to
increase the width of the pulse, ie stay on for a longer period of time. The
pulsing is fast so the field sees a n effective current, which will increase in
this case to increase the output of the generator.
If a very heavy load was taken off the generator, the terminal voltage of the
generator would tend to rise. The regulator this time would signal the
switching transistor to switch on for a smaller period of time, lowering the
effective current, which will decrease the current to the field, lowering the
output of the generator.
The voltage amplitude of the pulses remains the same, it is just the width
of the pulses that is varied, and hence the name given to this type of
regulation system is PULSE WIDTH MODULATION.
r - ~ '~
CONST@%L!-FR-EQIJENCY SYSTEMS;
,,
'
,
',
i 1 I--- - - \, 1- ----\
'.
For &craft where the load i s only resiitiye (heaters - anti-@ing, :I >,
The CSDU and the generator can be separate units but in later aircraft
they are one unit which is called an Integrated Drive Generator (IDG).
a) Non paralleled
b) Paralleled
In a non paralleled system each generator supplies its own b u s a n d all the
services attached thereto. So, in general, if there are four generators then
there are four buses each supplying their own services. The buses are
interconnected by relays so if one generator output drops off then another
generator can be switched in to supply some power to that bus.
Sometimes called a Non Load Sharing system.
With a paralleled or Load Sharing system all generators share the load to
the busses. This means that each generator is taking exactly the same
load as each of the others.
In this CSDU we are going to look a t an aircraft fitted with a JT8D engine,
which is a twin-spool axial flow turbo fan engine. At the front of the N2
compressor is a vertical shaft called the Tower Shaft, which is driven by
the N 2 shaft. The tower shaft drives the accessory gearbox and all the
mechanical accessories such a s the oil pimp, fuel pump hydraulic pump
and theJCSDU.
\ I
I
The CSDU is capable of adding or subtracting from the speed received
from the engine gearbox (4,300 to 8,600 rpm) to m a i n t a k khe generator
speed' a t 6,000 rprn a n d the frequency a t 400 Hz with small allowable
tolerances. 1
-.
\
1 /
' I -
OUTPUT SPEED
DIFFEREHTIAL
SPEED
IN PUT SPEED
This will make the pump act like a conventional axial piston pump and
suppl$ fluid to the motor, causing it to rotate - in the s-&e direction a s
the whole unit is rotating. I
This means the rprn of the dotor is now added to the rprp of the whole
unit to bring its output speed to that of the constant rpm required.,This is
--
called Overdrive. --
,
I
When the engine is running faster than the Straight ~ r i &speed the
control pisfon moves the wobbler plate in the other direction causing the
output from the pump to be the reverse from the Overdrive condition.
This will cause the motor to rotate in the opposite direction from the
hydraulic unit, deducting its rpm from the hydraulic unit's rprn and
causing the output rpm to remain constant at the required speed. This
condition is called Under-drive.
The drive input and the output to/from the hydraulic unit goes through
an axial differential gear box which houses a set of cyclic summing gears
that sums the output from the hydraulic unit to the output shaft to the
generator.
I Fig. 27 CSDU
Indications
WORM ENGAGEMENT-
THREAD
AND GOVERNOR
TO CSDU
DISCONNECT .
h
SWlTCH
RESET HANDLE
The disconnect solenoid is a guarded and lock switch on the power panel.
The normally closed contacts of the switch place a ground on the line to
prevent the possibility of a voltage pick-up from inadvertently tripping the
CSDU.
When the switch is activated one pole of the switch sends a signal to trip
the GCR which will trip the generator off-line. The other pole energises
the disconnect solenoid. This allows a spring-loaded pawl to move into
contact with threads on the worm gear. The input shaft acts as a screw in
a threaded hole and input rotation causes the input shaft to move away
from the input splined shaft, separating the driving dogs on the two
shafts. When the driving dogs have been separated, the input splined
shaft, which is still being driven by the engine, spins freely in the
transmission without causing any transmission rotation (figure 30).
I
I ! 8 8
1
- 25 -
rnoodull lA-763
Figure 3 1 shows an IDG schematic of a more modern aircraft (Boeing).
The IDG supplies 115/200V ac 3 phase 400Hz and consists of a CSD and
a brush-less generator in a common housing. The gearbox input speed is
5,800 to 9,975rpm and the output speed is 12,000rpm. So in this system
the CSD only a d d s rpm to the generator.
Note the input speed sensor and the disconnect mechanism. IDG
temperature sensor resistance's sense the IDG 'oil in' and 'oil out' and
sends signals via the Generator Control Unit (GCU) to the EICAS display.
I
I
I
I
BTB BTB I
I
I
I
I FWD GALLEY
I
- I
--
i
I
L------L-----A------------------------a7----------------
-
-- --
'\
\
,1'
1 7
-,
- -
r-Y
.
I
I '
' I
Fig. 33 N&q P A R ~ L ~ L ESYSTEM
D 1 , I
I
I
I I 1 /
I
I
1 ' /
If the engines are started and both generator outputs are okay then before
the GCB's are energised the APB must trip and both BTB's must trip,
leaving each generator feeding its own busbar and relevant busbar, ie
non-paralleled. If one generator should fail in flight the APU may be
started and its generator output can be fed to the relevant busbar.
For example, assume IDG L fails, then its GCB will trip, its BTB will close
and the APB will close and feed that busbar. If no APU generator was
available then both BTB's would close after IDG L GCB opened so the left
busbar could be fed from the right generator (the generator could not give
out more than its rated maximum so demand would have to be reduced
and some services curtailed).
- 27 -
moodull lA-765
The generator control units (GCU's) provide automatic control a n d
protection function for each channel by monitoring the IDG output. The
unit contains the voltage regulator and all the circuits for fault protection.
The power required to operate internal GCU circuits and external GCB
and BTB contactors is derived from the IDG PMG source with backup
from the aircraft 2 8 V dc.
: I : : . : SUPPLYlfRV REWTOR
; ' '"I"""
CURREUT
I l l II , GEMERATOR
PHG
1
POR VOLTAGE
EXTERHAL C T ' S b
GEMERATOR CT b
CWLlUG AIR 6CU W S I T I O U C
VENT HOLES BUS T I E SYITCH h
'4
GEM COHT SU
DRIVE DISC SY
F I R E SYITCU
F I E L D SUITCH
IOG O I L T E W I D 6 O I L TEMP
I b G IPU F I E L D OFF LIGHT
CHARGE PRESS SU HICRO BTB ISOLATE LIGHT
A W SHUTDOVW PROCESSOR DRIVE L I 6 H T
AIRI6UD M B CLOSE L T R I P
6CB AUX CONTACT B T B CLOSE L T R I P
BTB AUX CONTACT
I - -
1 //
--
Fig. 34 GCU SCHEMATIC
115V AC KHlEI
AIRlGNb
SYITCH U I D CDWTACT P O f l l I O N
EXTERNAL PWER INTERLOCK
CURRENT TRANSFORMER SENSING
AUTOUND WYER TRANSFER
---+UTILITY BUS RELAY
111s Irslmxrlws
FAULT ISOLATION
BITE
Each GCU and BPClJ h a s built-in test equipment (BITE) with self-check
a n d fault diagnosis capability. The BITE display and operating controls
are mounted on the 'BPCU.
1
I I 1 r-\,
1,
'-, I(_,
I /'
The utility bus relay (UBR) connects utility busloads to the main generator
bus. The electrical load control units (ELCUYs) connect aircraft galley
loads and electrically driven hydraulic pumps to the main generator
buses.
moodutl w
67
The APU generator provides 115/200V 3 phase 400Hz either in-flight or
on the ground, controlled and monitored by its own GCU.
FAULT PROTECTION
The GCU monitors the main generating channel, in the event of system
faults it trips the GCR, which then trips the GCB. Once tripped there
must be a reset procedure, which is to switch off the generator control
switch and then switch it on again.
(i) OVERVOLTAGE (130V) after an inverse time delay, trips the GCR
and the GCB trips.
I - - \
(v) OPEN PHASE - typicaly lowest phase 6 amps and next lowest
phase 40 amps, after a time delay trips the GCR and GCB trips.
(viii) UNDER-SPEED - IDG input falls below a set value trips GCB direct.
CONNECTOR
I I Fig. 37 -CURRENT\TRANSFORMER-
I -.
I 1 I _ /
Q
/
1 i
~ i ~ u38r shows
e the principle of o p e T ~ o n
using one phaseLline: ~ , d c h
phase line is identical and there are thr\&relays in the GCU-'
I
i
!?
/
/ i i
1
1
1
,
I
'
I
; i
/
I STAR POINT ;
icuRE6JT
/'
;
I j 8
1 1
: \-.-_---
/
TRANSF~ERS
- ......-...--- - ... ../'
- -
+"L.-o:
-
- -GCR then GCB
Operation
Under no fault conditions the current sensed by the load CT's and the star
point CT's will be the same. Current flows through the loads and aircraft
structure and through the star point CT's to the generator.
- 31 -
rnoodull l A-769
The CT outputs are equal and opposite. When there is an earth fault (as
shown in the drawing, the star point CT's have the load current and the
fault current, (which flows through the aircraft structure through the star
point CT's to the generator). So the star point CT's sense load and fault
currents, the load CT's sense only load current.
When the fault current is typically 20 - 40 Amps then the star point CT
output will be higher than the load CT and
sufficient current is fed to the relay to energise it and signal the GCR to
trip and hence trip the GCB.
BRUSHLESS ac GENERATOR
Figure 39 shows the relationship between the generator and the GCU.
Note the inputs and outputs to the GCU to include load shedding,
differential current protection, voltage control, bearing and diode condition
monitoring and communication with other GCUs.
- 32 -
moodull lA-770
Manual Tripping of the GCR
Typically there are three actions which will trip the GCR, trip the GCB and
disconnect the generator from the busbar. They are:
----. .-.
CAPT FLT INSTR BUS
HOT BATTERY BUS
rnoodult 123n
The GSB supplies power to in-flight loads and can provide power on the
ground for aircraft servicing operations. The GSB is energised from either
external power, APU generator or the right main bus. Control relays are
provided in the BPCU to operate an external ground service select relay
and an external ground service transfer relay. This busbar feeds main
and APU battery chargers and interior lights. For full list see the table
below which shows typical circuits fed from all the a c busbars.
AC BUSES
115V AC LEFT MAIN BUS 115V AC GND SERVICE BUS
HYD PUMPS MAIN BATT CHARGER
OVERRIDE FUEL BOAST PUMP APU BATT CHARGER
EICAS, LEFT EFlS INTERIOR LIGHTS
GRD PROX WARN SERVICE OUTLETS
WEATHER RADAR ANTI COLLISION LIGHTS
L ILS & RA WING ILLUM LIGHTS
DFDR POSITION LIGHTS
L FCC, TMC & SERVOS POT WATER COMPRESSOR
MCDP FUEL BOOST PUMP
115VACLEFTTRANSFERBUS HYD QTY
CAPT'S PHASE PlTOT HEAD HEAT EXHAUST FAN
-
AC STANDBY BUS PWR SOURCE WATER LINE HEAT
L ENGPROBE HEAT, L AOA PROBE HEAT SIDE WALL LIGHTS -
L DME, ATC, IRS, FMCS CMPTR & CDU 28V AC GND SERVICE BUS 1
28V AC TRANSFER BUS LEFT EQUIPMENT CTR LIGHJS
L & R FLAP POS IND INTERIOR LIGHTS, PASS SIGNS
RUDDER TRIM POS NLG SERVICE LIGHTS ,
115V AC LEFT UTILITY BUS I I 115V AC RIGHT MAIN BUS
CARGO FAS, HEATERS HYD PUMPS
PASS READING LIGHTS
--
- OVERRIDE FUEL BOOST PUMP-
LAV WATER HEATERS EICAS, R ADC, AIR DATA INSTR
AUS HEATERS -, R EFIS, RDMI & VSI
115V A CENTRE BUS R ADF, DME, VOR, ILS & IRS
C IR'S, RA & FCC R RA, ATC & FMC, R HF COMM
28V LEFT AC BUS R FCC & SERVOS
CONT POSIT SENSORS & IND 115V AC RIGHT TRANSFER BUS
CHART LIGHTS R ENG PROB HEAT
115V AC STANDBY BUS R AUX PlTOT HEAT, R ADF
L HF COMM, L RDMl 28V AC TRANSFER BUS RIGHT
L VOR MKR 8 L ADC EMER NIGHT LIGHTS & WORK LIGHTS
R ADF, C ILS LAV DOME OCCUPY LIGHTS
L CSEU - 1U2L, L PROBE HT IND 115V AC RIGHT UTILITY BUS
WARN ELECTRONICS B CARGO, RECIRC FANS
STDBY INSTR LIGHTS PASS READ LIGHTS
115V AC CAPT'S FLIGHT INSTR TRANS BUS LAV WATER HEATERS, AUS HEATERS
L IAS MACH, L ADC TAPE REPRODUCER
AIR DATA INSTR 28V AC RIGHT BUS
CENTRE EFlS DOORS
CAPT'S INSTR LIGHTS CONTROL INDR
L EFIS, ALT, AD1 & VSI HYD OIL PRESSURE
115V AC GND HANDLING BUS MAP LIGHTS
CARGO, SERVICE LIGHTS FLOOD LIGHTS
CARGO DRIVE & DOORS
WATER LlNE HEAT
LOAD
llPlCAL t L N I O I M l l C
PmVIIIWI FOR CWIECTIU6
tlltML cr
D :ow;;;,;;,;;tar*rL
As mentioned earlier this unit connects the aircraft galley load and
electrically driven hydraulic pumps to the main generator. The galleys
require a large amount of power and the ELCU not only contains a three
phase main contactor but consists of integral current transformers a n d
sensing circuits for over-current, phase unbalance current, differential
current, anti-cycle and lockout protection.
AC Load Shedding
I
1
L AC BUS R AC BUS 1
I I BTB BTB 1
&I
L UTILITY BUS
,
23L AFT GALLEY - 48
I
R U T I L I T Y BUS
([ORVARD GALLEY - 1s)
AUTOMATICALLY W I T H BTB
RESTORATION OF ANY (R AC BUS)
TUO POUER SOURCES
L UTILITY ) pEq R UTILITY )
FUD GALLEY )
ILLUMINATED
DURING
bE l C A S ADVISORY MESSAGES
L (A) U T I L BUS OFF
GENERATOR OUT
C O N D I T I O N AND
EXTINGFISHED,
A F T E R RESET
; '\ i
'
INF~IGHTGENEI~ATORLOSS i
I
Fig. 44 LOAD SHEDDING I '
-1 I
I
I
I
/ (Gj,,
--
-
I1
' 90 KVA
1
7XFTUBRP
i
L E F T GALLEY ELCU
1 /
FOR 4.5 M I H
l 1 1 ~ . 5KVA FOR 4!0 SECONDS
--
I
I R E
RIGHT UBR
FUD GALLEY ELCU'S
bE I C A S ADVISORY MESSAGES
L (R) U T I L BUS OFF
MANUAL RESET
CYCLE L E F T U T I L I T Y
MANUAL RESET
BUS SWITCH OFF-ON'
CYCLE RIGHT U T I L I T Y
BUS SUITCH OFF-ON
m-)
-
I I
ENGINE START PANEL
L AFT GALLEY
FUD GALLEY
SEtOHD.ENGINESTA4T
TRIPS UBR AND GALLEY ELCU FOR
ENGINE BEING STARTED
RESET I S AUTOMATIC U I T H GCB "OFF" I L L U M I N A T E S
CLOSURE DURING ENGINE START
-- -
OYERLOAD OYERLOllD
9 0 KVA FOR 4.5 N I N 9 0 KVA FOR 3 SEC
112 KYA FOR 4 SEC
-tp ---
Aum
-
TRIPS
- UBR'S AND RELAY
GALLEY ELCU'S
TRIPS ALL GALLEY
ELCU'S
-CYCLING EITHER
BTB S Y I T C H OFF-ON
FOR CONDITION ~ E I C A S ADVISORY MESSAGES
L ( R ) U T l L BUS OFF
The GCU's and BPCU are individually responsible for isolating faults and
storing the results in their Non Volatile Memory (NVM).
The BITE tests can be performed with the aircraft completely powered or
only with the battery switch 'ON'.
On the front of the BPCU are three switches, BIT (Built In Test), PERIODIC
an-d-RESET. -.. I
L
- L-
,, ,
' i i
r'
--
-1
AUXILIARY POUER
GENERATOR CONTROL
DATA LINK
RIGHT GENERATOR
LEFT GENERATOR
CONTROL UNIT
CONTROL UNIT
EXTERNAL PUR SYSTEH BUS WEI CCUTIOL UII EXTERNAL PUR SYSTEH
OK
LEFT GEN POUER SYSTEM LEFT GEN POUER SYSTEM
OK UNDER FREQ T R I P
RIGHT GEN POUER SYSTEM IDGIPHGIUIRING
OK RIGHT GEW POWER SYSTEM
APU GEN POUER SYSTEM OK
OK APU GEN POWER SYSTEM
LAST FLT 0 0 END OF DATA OK
' LAST F L T 00 END OF DATA
FOR PREVIOUS F L T PUSH NOW
FOR PREVIOUS F L T PUSH NOW
NO SYSTEM PROBLEMS
LEFT CHANNEL
UNDERFREPUENCY T R I P
--
/
Pressing the periodic test is normally,performed a t scheduled aircrkft
I
-
-
maintenance checks. 1
I I ! I
I
I
I ' m ,
I
Pushing and releasing the PEAODIC tdst switch starts the maintenance
BITE test, which is a limited end-to-end test of the GCU and BPCU. The
results of the test are stored in the NVM. When the test is complete and
stored in the NVM, the contents of the NVM for that fligh-t are displayed.
( O I I
EXTERNAL PUR S Y S T E V r
7 71
L E F T GEN POUER SYSTEM
OK
R I G H T GEN POWER SYSTEM
GCU F A I L E D CODE 59
EXTERNAL PWR SYSTEM
APU GEN POUER SYSTEM
L E F T GEN POUER SYSTEM
OK
R I G H T GEN POUER SYSTEM
L A S T F L T 00 END OF DATA
APU GEN POWER SYSTEM
, FOR PREVIOUS F L T PUSH NOW
I I
RESET D I S P L A Y SEQUENCE
P E R I O D I C TEST D I S P L A Y SEQUENCE
The RESET switch clears the BPCU and GCU memories each time it is
pushed. This action makes previous memory entries inaccessible. Each
time the switch is pushed, the display will state that the BPCU, left, right
and APU GCU memories were cleared when the power system name
appears.
II 1' - I
I I
I
II I i I
I
f 1 ,
1 I#*? L Cn lllt PYR ,
1
L--
\
be-r
PC-v
10
28
67
28
48
27 ' 0
28
I1 1: IDC
lD6
OUT
I
101
10
103
12 I I I
! I
i I I
,
/
' - 1
nlvu PRESS
-- L c/,
LOU MOM'
/
HIKH
I
,
i
-
k J
- 41 -
moodull l A-779
a) They must have the same output voltage.
LAMP
GENERATOR 2 -
' I
This beat frequency will increase or decrease depending on how far 'out'
the generators are with each other. If a lamp is connected across each set
of contacts, as shown, then the lamps will go on and off a t a rate
determined by the beat frequency. A s the generators drift into phase with
each other, for instance, the lamps will dim and then glow brightly a s the
generators drift apart again. The correct time to close the contactor is
when the lamps are out. This method of telling when conditions are right
for paralleling is known a s the Lamps Dark Method. There is also a
Lamps Bright Method (cross-connection of the lamps) but it is the Lamps
Dark Method which is the basis of all aircraft paralleling systems whether
manual, semi-automatic or automatic.
The same thing applies if the generators are at the same speed but are a long
way out of phase with each other. It is only when they are very close
together that the lamp will be going on and off at a rate that is slow enough
for manual paralleling to be put into effect.
I
i
I I
I I I
i L- -_-.' I
With rkfqrence to figure 53, asskmiiiiith&yo 2 generator is connectdd to
the syn&ronising Bus (Synch BUS). No b gtnerator is connected to it's own
load busibut is i,@lated from thk Synch bdsljars by it's trip$e$l Bus Tie
,I
/ / ;;
~ r e a k 4 (BTB).
r
, /
I
1 1
/I \ ..'
I1 :! ,I
, ,
i ; I
-
8
/'
~
7- -.,I '--,
LSYNGHBUS
rnoodull l A-781
When No 1 is selected for paralleling, the two lamps will each receive
supplies from identical phases (A and C) of the two generators. At the
correct moment (lamps dark) the BTB is closed and the two generators are
paralleled. It is subsequently possible to select and parallel Nos 3 and 4
generators a s required.
In this system the engineer is relieved of the task of closing the GCB when
the conditions are right. He still decides whether or not generators are to be
paralleled but the actual operation is automatic. This device will close the
GCB when:
(a) The Frequency Difference (Beat Frequency) is less than 3-5 Hz.
TO CLOSE
N O 1 GCB
4
-0
-
; - 0 nav DC
C PHASE
OF NO I
BUSBAR
C PHASE
OF NO 2
BUSBAR
This will break down 21 and switch on Q2. The operation of relay RL1 will
now close and the GCB and the two generators will be paralleled.
PARALLELED SYSTEM
The IDG h a s a variable speed input from the engine gearbox and through a
1'
RIG^ 6 l E F T H?OMUOCp
U N n S (VARIABLE
DISPLACEMEW PUMPS 6
FIXED DISPLACEMENT
MOTORS
V A R W L E SPEED
D R N E FROM ENOINE
INWCATOR
FLYWEIGHTS
PRESSURE TO ONE
SIDE OF THE CONTROL
PISTON
\ ELECTRO MAGNETIC
CONTROL
ADJUSTER
URE TO T H t
OTHER SIDE OF THE
CONTROL PISTON
I] ' TO LOAD
CONTTRC
)SUPPLY PRESSURE
I
I I
Note the Ground Handling bus (GH), the Ground Service b u s (GS) feeding
similar services as described in the non-paralleled system. Each main ac
bus feeds the dc b u s via TRUs. The GS bus feeds the Battery Chargers
(B/C) for main (MN) a n d APU batteries. Standby ac power is available
through a static invertor. The system shown shows two APU's and two
external power sources, many aircraft now only have one APU fitted.
-- A
- - . .
---\
I 1
' I
6WCH BUB
- --
TRANS
6
+ oq-1Ac
INVERTER
:4p' sTBy *c
Assuming the APU 1 is running and the Auxiliary Power Breaker (APB) is
made the Split System Breaker (SSB)will close and with the Bus Tie
Breakers closed the APU can feed all the AC busses (AC1, 2, 3 & 4). The
Generator Circuit Breakers (GCB's)will be open; the APB cannot close
unless all GCB's are open. If the second APU was fitted then the SSB will
open to prevent paralleling of APU's.
A similar sequence would occur if ground power was being used instead of
APU power, this time the external power contactor (XPC)would be closed
and via the BTB's feed all ac busses. Once again the XPC will not close
unless all GCB's are open. If the second external power is switched in the
SSB will open.
Starting No 2 engine will allow its GCB to close to parallel the two generators
providing the auto-parallel senses that conditions are correct. Sim.ilar action
takes place when starting engines 3 and 4; there is an auto-parallel circuit
either side of the SSB.
So when all engines are running all GCB's, BTB's and SSB are closed and all
the generators
- are paralleled. -----
Should a fault condition occur such as a &merator failure then its GCB will
trip leaving the other three gederators to power the four loaid busses. Even if
three generators failed one gen'erator can
'
feed all four load busses but some
load shddding will need to take place.
-
I
--
I
If a generator will not load shafe, the BTB *ill trip allowing the genkrator to
power its own bus in isolation from the others. If the load b J s shorted then
the GCB a n d BTB will trip isolAting power from the shorted area.
I
If there i s a-short on the synch b u s two BTB's and SSB win trip, removing
power from the shorted area without loss of busses.
The two main units in the system are once again the GCU which contains,
voltage regulator (action similar to that previously described), reactive load
division circuit, generator control relay (GCR),GCB Control, BTB Control,
essential relay control, auto-parallel circuits for generators and fault
protection circuits.
The other unit is the Bus Power Control Unit (BPCU)or Bus Control Unit
(BCU)which contains XPC control, APB control, SSB control, ground
handling and ground service relays, SSB Auto Parallel, external power fault
protection and a galley power trip signal.
From the diagram note the essential ac bus which feeds radio and flight
instrument systems is normally fed from No 4 generator, but a flight deck
switch can select any of the other three generators.
Load Sharing
A s the generators are paralleled then load sharing must take place. (It would
be convenient a t this point to do some revision (CAA JAR module 3) on ac
power circuits).
-.
--
POWER-IN AC CIRCUITS
I
r
'
-
I
-- \ - --
-',
a) In a purely resistive dircuit, ALL of the current holeswork and
POWER is produced.
I
i
I I
I
I
I l
1
I i
I POWER is produced. 7 - \\ I
\
'\\ ,'
I
I
1
I
'
I \ i I
) 11
1 I POWER is produce?.
il I
J
'
'
\
In a,hurely capacit rvq circuit, $hb current does Lo!work and NO
II
! I / ,
: '
L
,,
l. ji [
L...../'
/,, )' ; 8,
The phasor diagram shows the current lagging the supply voltage by phase
angle 0. From our previous theory, power is only produced in an ac circuit
when current and voltage are inphase. So we need to split the current I into
its two components as shown.
The component 'in phase' with the voltage also known a s the ACTIVE or
REAL component and the component a t 90" to the voltage known as the
QUADRATURE or REACTIVE component.
It is very important to realise that only one current (I) flows in the circuit and
this is the current that is measured by an ammeter in the circuit.
- Icos0
I-
IREAL - -
As sin 0 -
- IREACTIVE
IREACTIVE - I sin 0
If the supply voltage is multiplied by the current (I) this will give u s the
APPARENT POWER being dissipated, we know that this is apparently
available but because current and voltage are not in phase then that is not
the true power available from the system.
As we have seen we can work out the apparent power of a system in KVA.
What we need to know is how much of this available power is producing
actual work done in a circuit, ie producing True Power. So the ratio of
TRUE POWER
APPARENT POWER
Example
If 4OKVA generator produces a power output of 30kW then the power factor
is:
pf = 30 = 0.75
, 40.-
1-
- -
-
-- ---
\
--
-
- - .
\
\ /-
8 \ , -
- \ \
So in this case the factor of podei being qskd is 0.75 and tde gene;?tor is
producing 0.75 of its output as True Power,,ie producing power in the
system. So obviously the higher the power factor the better1 Aircraft '
generation systems are typically 0.75 A . 9 pf. A pf of 1 (unity3 would mean
that all of the power produced ia Being-u$d as true power and-the circuit
I 1 -- I
,,"
I 1 I I
I I I / I
pf TRUE POWER ( T P ~ I
=
APPARENT 'POWER (AP) '
l
'
I
I
, -
L -- ', i-
I I
-
--
-/
' ___I
A s TP - VxICOS0
and AP - vxI
then pf - VxXCOS0
vxx
pf -
- COS 0
So another formula for power factor is that it equals the cosine of the phase
angle.
The true power is produced when current and voltage are i n phase.
TP = VxIxCOS0kW
RP = V x I x s i n 0 kVAR
AP = V x I kVA
- cos 0
ACTIVITY
-
I I
I I
Consider the case of two generators sharing the total load equally, ie each
carrying 60 amps. To understand the operation of the loop, it is necessary
to 'stop' the action a t one moment in time. At this moment the output of
each current transformer (CT) is trying to:
- 52 -
moodull l A-790
- -\ - ,'-i
-- -
Fig. 60 LOAD-SENSING -1 ,L-- -- .\
,
1 / I \' > i
1 '
I
\
1
I I
I
If the two generators are sharing the loaq edually assuming ie&h CT /output
is 0.5X then the sensing loop c d ~ e n t w h i c his always the abefage of CT
secondab currents in this case is also 0.6~. A s both of the f2~-out@ut/sare
,'
trying to drive currents througp their op\po;ite sensing resistofsas well as
their o-, then CURRENT IN THE SENSING RdlSISTORSas they
I I
cancel each othdr out. I1 1 1 1
I I ' i '/ 1 / I !
L/,'
/ -i \
-- -
- --
425A
But the current flow through the sensing resistors is no longer equal and
opposite and it is the DIFFERENCE current between the CT and the sensing
loop current which flows through the sensing resistors. Note they are in
opposite directions, so one signal will signal the system to decrease its
loading, ie generator 1 and the other signal will signal its system to increase
its loading, until they again balance.
- c---- 5 . 2 5 5.25
,
I REACTIVE
LOAD 20
REACTIVE -
LOAD 70
REACTIVE
LOAD 60 I
REACTIVE
LOAD 60
I
/
A L L CONTACTOAS
CLOSED P O S I T I O N
(AUX CONTACTS
GCU I I %:ER:: I u
scu 1 GCU 3 GCU 4
The total reactive load on the aircraft is 2 10 amps and there is unequal load
sharing. The average current in the sensing loop is
The difference current between loop and CT output goes through the sensing
resistor so in GCUl 5.25 - 2 = 3.25 amps flow. In GCU2 5.25 - 7 = 1.75
amps flow (in the reverse sense) and in GCU 3 and 4 6 - 5.25 = .75amps
flow (in the reverse sense).
So signals from the sensing resistor are fed to the voltage regulator which
will increase the generator excitation to increase the reactive loading of IDG
1 a n d decrease the excitation to IDGs 2, 3 and 4 to decrease t h e reactive
loading in proportion to the sensing currents.
I REAL
LOAD 20
REAL
LOAD 60
REAL
LOAD 60 i
A similar action takes place in the Real Load sharing circuit (figure 63). The
sensing resistor this time is in the LOAD CONTROLLER and its signal is fed
to the magnetic trim coil on the speed governor on the CSDU. Movement of
the governor piston will modify the hydraulic fluid fed to the drive to increase
the drive torque of any generator carrying too little real load and decrease
the drive torque of any generator carrying too much real load. So in the
example the signal will be to increase the drive torque of IDG 1 a n d decrease
the drive torques of IDG 2, 3 and 4.
Note. In both systems the current transformers are shorted out when the
relevant generator is not load sharing by contacts of the GCB or BTB. This
ensures that the CT does not overheat with possible burnout.
- 55 -
rnoodull l A-793
FAULT PROTECTION
CLOSE
TRIP
I
O M1 GEN 1 'OWER GEN3--- I I
\ GEN4
A similar action will take place with the under excitation of one generator to
a set level, and again trip the BTB, if the fault is an under-voltage fault then
the generator will be tripped off-line.
The layout goes from engine (CSD)to GCB (load bus), BTB and
synchronising busbar. Note the kW (Real Load)/ kVAR (Reactive Load)
meters, just to the right of the meters is a switch marked kVARS. The
metersnormally read kW but rpressing-tkq switch and they-will-read, kVAR,
henciS7pC &crew can monitor tealand-rehctive load sharifig. -1n-the'bottom
1 I
right h , 4 d comer there is a frequency \
meter '
and ac voltrne??r; just below is
a select panel which you can s e ~ e hrelev$ntlsystem display. Fkom this panel
GEN TEST can be selected and YTfIG voltagy will appear on the voltmeter.
i-, /'
< ' 1
, 1' /
/
I 1, I
1 '' i ,/ 1
moodull lA-795
Fig. 66 ELECTRICAL POWER MAINTENANCE PAGE
--
- -
o l (BCU7s)and GCU7sto
BITE circuitry is provided in the 1 3 G ~ o ~ t rUnits
identify an electrical power system failure. , I
1 '
An example (Boeing) of one test is using the Central Maintenance Computer
(CMC) and the Control Display unit-FDU).
BCU 2
Ground tests are selected from the CMC menu on the CDU. Selection of
electrical system ground tests are made by pressing the line select key next
to 24 ELECTRICAL.
GROUND TESTS X X l X X
(24 E L E C T R I C A L
(26 FIRE PROTEClION
fi 3
- b BROUND TESTS lllXI
0 <EPGS CBCU 1 ) 0
a < E P G S ( B C U 2) I 3
I-
- 1
i-
I
7
r-
1,
-, \, - , --
\
I i i \
By pressing the line select key next to the, &stem to be testedithe test is
activated which takes 10 seconqs Whenltl$etest is completed PASS or FAlL
i
appear's. If the system failed pqessing the line select key ne? to FAIL causes
I - - / /
the grdund test messages to appear. The<followinginformation Lappears on
the pa&e,er
I
I ,-I
,
I N -- \\,
I
-
/'
I
i
\
I 1 ~ a i i e dunit and1 cause
I I1 iI
' i c~c'rhessa~
I I nurnbkr)and
e $ring diagram number AT^
, li ~ ~ u i ~ r n e ~ n b om
- / ,f the
b e failed
r unit I
- - -- EIGAS-ale& message
Flight Deck Effect
1
-( <tPSl ILICU 1 ) -
- 59 -
moodull l A-797
VARIABLE SPEED CONSTANT FREQUENCY (VSCF)GENERATOR
With this type of generator, the CSDU h a s been removed a n d a s the name
implies, t h e variable rpm engine input produces an initial 'frequency wild'
supply within the generator which is converted electronically to a constant
frequency output. The benefits include: weight saving; reduction in direct
operating costs; less maintenance; improved reliability, and less stock
required (less number of parts compared to the IDG system). The VSCF
generator was designed as a one for one replacement for the IDG and does
not require any changes to the aircraft wiring or plumbing.
COOUMG
C N L
oRAln OIL &* 1WSTllVCTIMl \ SERVICE PORT
A1 R PLUG PORT IDEM1
EXHAUST PUTE
The stator assembly consists of three armatures: the main ac stator, the
exciter stator, and the permanent magnet generator (PMG) stator. The rotor
assembly consists of a shaft, permanent magnet rotor, exciter armature,
rotating rectifier, and main dc field. The oil pump is mounted within the
generator frame and is driven by a gear on the generator shaft. The oil
pump drive gear ratio keeps the maximum speed of the pump below 12,000
rpm. The pump contains rotor-type elements that draw oil out of the sump
in the inverter power module.
There are 6 ac terrninals a t the top of the generator. TI,T2, and T3 are the
power terminals; T4, T5 and T6 are the neutral terminals.
T1 and T4 are for phase A and the leads are colour-coded red.
-- \
\
- -\
T2 &dl ~ 5 a r for
e phase C and the-leads\& colour-codedi61uF-. ' ,
1 ; \ ', 1 I \
T3 and
I
~ i are
6 for phase B and ihk
1 1
leads b e colour-coded ykllow.
1 I I
i ,I 1 ! i
The rn h connector is on the tdp ~fthg/~e/nerator and contains c i r c k ? ~for -A
There y-9
I
and F, for the holtage regulator legds from the
' I
GCU (p6). - I
, -'I
!
L---
/
OUTPUT
3 PHASE 3 PHASE 4 WlRE
INPUT 3 WIRE 3 PHASE 115V
VARIABLE SPEED AC 4 WIRE mHZ
DRNE FROM 1370 TO 3 PHASE PWN 115V AC M) KVA POWER
GEARBOX 2545 HZ 270V DC WAVEFORM 400 HZ
FIELD VOLTAGE
EXCITATON SIGNAL 6
FROM INVERTER
VOLTAGE STATUS
REGULATOR
OUTPLiT VSCF OUTPUT
TRANSISTOR SIGNAL
CONTROL
GENERATOR
OUTPLn
SIGNAL
+. 8 ,
e
POWER SUPPLY FROM PMG
CONTROLS. MONITORS
6 HAS BIT FUNCTION
- 61 -
rnoodull l A-799
Operation is as follows (refer to figure 71):
2) The dc filter rectifies the generator output to 270V dc. The dc filter
uses large capacitors to remove the ripple from the d c link voltage.
3) The inverter uses six large transistors to convert the d c link voltage to
a three phase, Pulse Width Modulated (PWM) waveform. Inside the
inverter is the neutral forming transformer. This adds a neutral lead
to the three-wire output of the transistors. The neutral forming
transformer permits the transistors to equally share a load that is not
balanced.
I
-
\
-
I
..
6) The generator/converter cqntrol unit (GCCU)uses a rni'cro~'r~drqcessor
to
bperate. It gets power from the PMG in the generato{ housing. The
I
GCCU h a s ,two important functions: I
i
I I I 2 ,
A BIT feature is included in the VSCF unit, which is designed for two levels
of interrogation: flight-line maintenance and shop maintenance. Three
possible reasons for performing a BIT check are on ac system malfunction
with illumination of a fault light, low residual voltage (5-10 volts), or a
scheduled maintenance check. Flight-line BIT is done using a two-throw,
centre off switch on the converter module with BIT fault data displayed by
two red LED'S located adjacent to the switch. DC power for the BIT is
through the "low oil pressure" light and requires the "LIGHTS" switch in the
'E3RT' position. One LED is labelled "VSCF Fault Detected" and illuminates
with the switch in the 'INDICATE position if BIT has detected a fault within
the unit (this information would have been stored by setting a latch relay).
- 63 -
moodull lA-801
The second level of BIT is intended for the shop technician performed on a
removed unit. This level uses information stored in non-volatile memory for
the previous 20 flight cycles (defined by engine run cycle-PMG speed).
(
Relative system performance parameters and protection trips/faults are
stored. The information is accessed via an RS232 serial data port (pins 17,
18, 19 on the main connector) by any "IBM compatible" personal computer.
This level of BIT, used in conjunction with common shop test equipment, will
identify a failed SRU or sub-SRU with a minimum accuracy of 95Oh1 without
using a rotating drive-stand. A trouble-shooting program for the computer
will be supplied to supplement the component maintenance manual for this
test.
- 64 -
rnoodull l A-802
CONTENTS
Page
APU Generator 1
Hydraulic Motor Generator 3
Ram Air Turbines 4
Back-up Generators 7
Rotary Invertor 7
Voltage Control 9
Frequency Control 10
Torque Switches 13
y Normal Operation 13
Failure Operation r-- -- 14
Static ~ ~ v ~ r - k o r c 'h14
operation I [ .\I f4
Extern$/, Ground Power I I i 16
q C External Power I 1b I
The emergency power generation for an aircraft with ac generators could be:
r--
-
- d)
\
, Static Invertors , --
I , e) ~ack-up-~ener+tors , , -
1 '
i I
I
APU ~ d n e r a t o r / ,I
----,
,
1
,
'
~
1
'
iI
I
I
1 1 r -I, \
The ougput of this generator is used to suqply the busbars d?ring servicing
1 --
i /
' I
and ma!inkenance1 of the aircraft bd the grohdd, so the aircraft play be
indeperidknt of grdund support equipment; vowever, it can pe used as an
emergency sour6efof power in flibht, in thd event of failure 04 the main engine
gener,afors
- - - -
a g y o u have already-seen-from t h e AC Generation
1pH
Book. i
The generator components are usually the same as the main engine IDG's
and are interchangeable except the APU generator is contained in its own
housing (often of cast magnesium alloy) and has a different input spline and
mounting flange.
TERMINAL BLOCK
\
WITH 4 STUDS
LOCATING PINS (3)'
MOUNTING FLANGE
The APU being a small gas turbine engine of its own is electronically
controlled via the electronic control unit (ECU) which supervises all
operations of the APU. The APU speed, and therefore generator speed, is
achieved by fuel control and a typical speed on a modern passenger carrying
aircraft of the generator driven by the gearbox is 12,000rpm.
The APU can also provide pneumatic output (for cabin conditioning and
pressurisation etc) and the electrical power and pneumatic output availability
may depend on aircraft height. For example, on the Boeing 757 the APU is
certified to start u p to 30,00Oft, it is capable of supplying 115V ac 3 phase
electrical power u p to the service ceiling of the aircraft. Pneumatics are
available u p to a n altitude of 17,500 feet. Each aircraft's specification for the
APU will obviously vary. The APU is started by its own dedicated battery with
its own battery charger. - - -
. / L.
--- .
I
a , D I G I T A L OATA
----- CONTROL SIGNALS
- POWER FLOU
ELECSYS PANEL
With reference to figure 2, assuming the left IDG failed, then the GCB would
be tripped. If the APU was then started and selected 'ON' the APB and left
BTB would close allowing the APU to feed the left busbar leaving the right
IDG to feed the right busbar, its BTB being open (non-paralleled system).
HYDRAULIC MOTOR GENERATOR (HMG)
The HMG system provides a backup source after loss of all generated
electrical power. A hydraulic motor supplied in this example by the left
hydraulic system drives the generator. The generator h a s an output of 5KVA
30 120/208V a c a t 400 Hz and 50 ampere, 28V dc power which provides
power to the standby system, captains flight instruments, selected navigation,
communication, lighting and anti-icing loads when both main a c buses are
un-powered in flight.
LEFT HYDRAULIC
SYSTEH PRESSURE MOTOR GENERATOR
SHUTOFF VALVE
I- - --
-
1
1 ' I
Fig. 3 HYDRAULIC MOTOR GENERATOR SYSTEM
--
I 1 --__ I
! 1'
I !
I i
The gederator portion of the HMG i s compgsed of a permanent magnet
generator, excitek,generator and;main genfrdtorI with rotors iniunted on a
common shaft,.' The permanent ,magnet.generator supplies 3'phase 800 Hz
power-to the GCU for excitation control and protective funcfions! The main
generator h a s two output windings a s mentioned previously, one produces ac
and the other is full wave rectified to provide dc.
-3-
rnoodulllA 806
An example of HMG Power distribution is shown in figure 5. The a c bus
transfer relays connect the left and right ac transfer buses a n d the captains
flight instrument transfer bus to the HMG ac output. The two 1 1 5 / 2 8 V ac
single phase auto transformers supply 2 8 V ac loads from the left and right ac
transfer buses. A dc contactor connects the hydraulic motor generator dc
output to the hot battery bus.
BTB BTB
_I C
1
INSTR BUS
VOLTAGE
1
- - " XI""
BUS RLY
RLI
28V AC BUS
HOTOR
K10564 HID
STATIC
GEN DC
INVERTER
K104 MAIN
Kt09 STBY BAT. RLY -
PUR RLY HAIH 7
i
BATTERY
&
I
I
I
I
As can be seen from figure 7 the ac output from the RAT is converted to dc
and supplied to the captains and first officer's instrument buses. The
captains flight instrument bus supplies power to the battery bus 2. The
battery bus supplies power to the hot battery bus and the static invertor,
which provides the single phase 115v 400 Hz for the ac standby bus.
RAT
- GENERATOR --
1 1 \
1 I
I
- - - - >
7
-
-
I
II
Figure 10 shows the system. If required the left back-up generator feeds the
left transfer b u s and the right back-up generator feeds the right transfer bus.
If both transfer buses require power the right back-up generator supplies
power.
INVERTORS
ROTARY INVERTOR
I I
/
COMMUTATOR BASE
SUPPORT
ARMATURE
1 CARBON PILE M I
, I
I
0
I
/ ,
--
CONTROL - -
COIL
DC
- *
INPUT 3 PHASE
AC OUTPUT
C 7
*
3 PHASE
RECTIFIER '
-8-
moodull 1A-811
The ac output is taken from three slip rings and is 3 phase 1 1 5 V 400 Hz. The
d c input being via the commutator a t the other end of the machine.
These machines are used on a fairly constant ac load, so control of the output
is achieved by carbon pile control as shown in figure 12.
If the output should rise this will be sensed a t the output, converted to dc by
the three phase rectifier and fed to the control coil of the carbon pile
regulator, which will de-compress the carbon pile, input current will fall,
motor speed will fall and output will return to normal.
DRIVE SHAFT
I
2 8 V DC 3PHASE -
SUPPLY 115V400 HZ
OUTPUT
,
The dc motors were generally of the compound type and the ac, generators of
the star wound rotating armature type. Most invertors are self-cooled by
means of fan assemblies fitted to the rotor shaft. In these invertors two
-
separate control systems are required. ,
--
Voltage Control
In this type of control the generator excitation field system h a s two windings:
the main excitation field fed from a dc source and a control field fed from the
magnetic amplifier. The current in the control field is passed in such a
direction as to produce a mmf, which assists the main field.
-9-
rnoodull l A-312
115V 3 PHASE
400HZ OUTPUT
+ AMPLIFIER
GENERATOR
SECTION OF + DC
INVERTER INPUT
Frequency Control
The motor of an invertor being essentially a shunt machine allows the use of
a control field incorporated into the motor main field system in the same
manner as for voltage.
The motor control field is so wound that the passage of current through it
produces a magnetic affect to assist that of the main rotor field system. By
varying the amount of current through the control field the motor speed and
thus output frequency can be varied in relation to the variation from the
desired level.
MAGNETIC
-
1
AMPLIFIER FREQUENCY
ERROR
+ ................................--................. """ .......... ........., SENSING
li
1 I
11 -
A
I - 3 PHASE
AC OUTPUT
I --
...........................-,.......--..-.....-.......---.... ..............
,.....
-..-....-....--....----.-..,
SERIES I CONTROL1 !
RESONANT
CIRCUIT -
;-m
.I
j
i TO
j MAGNETIC MOTOR
I j
I
AMPLIFIER i
!
FIELD
41
II
Ib
t
PARALLEL i CON1'ROL 2
RESONANT
CIRCUIT
- 11 --
moodull l A-814
This circuit is fed from the ac output of the invertor. The tuned circuits are
resonant at dissimilar frequencies above the nominal value, and the control of
the magnetic amplifier depends upon the difference in current in the two
control windings.
CURRENT
RESONANCE
-
--
100 2 h 300 400 5&0 600 700 800
FREQUENCY (Hz)
I
If the frequency falls below normal, the parallel circuit increases current
through control 2 and the series circuit reduces current through control 1.
The magnetic unbalance is now reversed, and the motor field current is
reduced, increasing motor speed and restoring frequency to normal.
Efficiency
Invertors have a relatively low efficiency, about 50 to 55% on full load. When
lightly loaded their efficiency is even less, which presents a considerable drain
on the main electrical system. Some of the systems would have phase B
earthed, ie use the airframe as the phase B line.
Torque Switches
These are used as a means of detecting whether the nominal frequency and
voltage of the aircraft instrument supply circuit is within its prescribed limits.
Used to operate the changeover circuits, from NORMAL to EMERGENCY in
the case of invertor circuits, or to operate indicator circuits.
CONTACTS
RIGHT HAND
CONTACTS
I ,
The front compartment of the switch unit houses the switch mechanics,
which consists of a control spring connected by a gear wheel to the pinion on
the rotor shaft, and a set of contact assemblies. The contacts, being
adjustable, are set to operate a t a low operating pressure. The contact arm
assembly is mounted on the geared shaft, which also carries the control
spring. The front compartment of the switch unit has a Perspex (transparent
plastic) cover to allow visual observation of the switch operation.
Normal Operation
When the correct voltage and frequency and the correct phase sequence is
connected to the terminals the windings are energised and the rotor will turn.
This will t u r n the pinion and the gear wheel until the torsional resistance of
the control spring equals the torque exerted by the motor. In this condition
the motor will stop. The contact breaker will have opened or closed the
contacts a t this point.
Failure Operation
Should the supply voltage and frequency decrease, the motor torque is
reduced, and the shaft will move under the influence of the control spring to
the de-energised position. The contacts will now operate.
STATIC INVERTOR
A s the name implies the components are of the solid state type. Some aircraft
may use them a s a normal source of ac power, but on most modern
passenger carrying aircraft they provide an emergency source of a c power in
the event of main generation ac failure. The output is single phase 115V 400
Hz. There are many different types, but we will look at one example.
-- -- - ---
,
28 V
-
FILTER
-
!r .-- \
'
-
\
DC NETWORK I / \
CONSTANT i
CURRENT
GENERATOR
I
400Hz SQUARE
I -- -
VARIABLE '
PULSE
WIDTH
@7
ODD 1
HARMONIC
FILTER' 115V 40OHz
I - SINGLEPHASE
OUTPUT
VOLTAGE
SENSOR
CURRENT
CCuCnm
Operation
- 14-
moodull l A-817
This output i s then supplied to a pulse shaper circuit, which controls the
pulse width of the signal a n d changes its waveform before it is passed to the
power driver stage. The purpose of the turn-on delay is to allow the voltage to
stabilise before there is an output to the power driver stage.
The power driver supplies a pulse width modulated output to control the
output stage, this signal having a square waveform. The power driver also
shorts itself out each time the voltage falls to zero (during notch time).
The output stage also produces a square wave output but of variable pulse
width. This output is finally fed to a filter circuit, which reduces the total odd
harmonics to produce a sine wave output a t the correct voltage a n d
frequency.
--
(-) FY, .C
OR F S S OC
I
FAILS
Some aircraft use power from a ground power unit (GPU) for servicing and
maintenance of aircraft systems. So the GPU output must be connected into
the aircraft at a convenient point, usually located low down on the side of the
fuselage. In the majority of large passenger carrying aircraft the aircraft is
completely independent of GPUs as they use the APUs, however should there
be a n APU failure then connectors are available for dc and a c external power.
DC External Power
Figure 21 shows a dc external supply socket, ie the end of the lead from the
GPU and the 3-pin plug, which is on the aircraft. The plug has two positive
pins, one being shorter than the other and one long negative pin.
-- AIRCRAFT SKIN , -
r- -' - -\
I
-, '\
I
\
I I
I
II I
1 --
'
I
i
SOCKET I
P -- ,
,
I
8 I
-- - - A - 1 _
Figure 22 shows a simple dc power system. When the power selector switch
is placed to 'EXT' the positive supply from the short pin will energise the
external power relay, allowing the GPU supply to be fed to the main busbar.
DC BUS BAR
?
EXTERNAL
-
-
- : POWER
( 0-411
+
I SELECT
*-+
EXTERNAL POWER TO BATTERY SYSTEM
CONNECTOR
- 16-
rnoodull lA-819
Note that if the socket is withdrawn with the circuit still live' then the
external power relay will de-energise before the main pins are disengaged
from the socket, this ensures there is no arcing at the main pins on the
socket.
AC External Power
DC INTERLOCK
RELAY
SUPPLY PINS
PHASE
PINS
GROUND PIN
I
I
- -
IHDICATIOH
LIGHTS
EXTERNlL WER 1
SUPWRT ROD
EXT PYR
-- -
--
L
GROUND ,, /
HANDLING c
I
RELAY
1
LBTB I ,'
- a -
GROUND
POWER,
T-R UNIT
/ ' I
The Bus Power Control Unit (BPCU) controls the closing and opening of the
External Power Contactor (EPC) allowing external power to be connected to
the a c tie bus. Connecting external power of acceptable quality illuminates
the AC CONNECTED, NOT IN USE and AVAIL lights on the flight deck.
Pressing the EXT PWR switch closes the EPC causing the EXT PWR ON light
to illuminate and connects external power to both ac buses via closed b u s tie
breakers (BTB's).
Other protective functions while the external power is connected are: ( I ) tie
b u s differential protection, which isolated any short circuit fault on the
i external power feeder or tie bus, (2) overcurrent, ( 3 )underlover voltage, (4)
overlunder frequency, (5)open phase and (6) overload, i n each case the
EPC is tripped.
GRWWD HUIOLIffi R E U Y
GROUlD IERVtCE SELECT R E U Y
6RCW0 S E l I C E TRANSFER R E U Y
EXTEIWAL m E a , c o m r ~ c T a a
FLIGHT c m p h n m r n r IIIDICLTIWS
ELECTRICAL LOAD C M R O L M I I S
U L L E V U)bb R E U Y S (OPTICAIL)
U T I L I T Y BUS I E U Y
DATA W E S
TOIF1101
SN'S
TRANSFORMERS
CURRENT TRANSFORMER
Within the electrical power system, there are a large number of current
transformers used. First it would be useful to re-cap on the theory.
The Current Transformer is designed to enable circuit currents to be
measured without breaking into the circuit, as is necessary with an
ammeter or its shunt. The output of the current transformer may be
applied directly to an instrument or be used in control circuits.
SECONDARY COIL
- ,- -
', - -,
I I
I I
- -. \
,
I '
operation i! t1 I
I I / 1
! I
Wheli the load passes througl! the suppiy cable, it creates la magnetic field
along it=hole
- length which-is const&$i building-up, collapsing,
reversing, building-up etc. ItpiSth-i~fluX
which induces emfsihto the coils
of the secondary winding.
As the ring former and secondary coil only take up a very small length of
the primary cable, it is obvious that, whatever happens a t the secondary,
the effect on the primary will be virtually nil. The primary, which depends
on the load, may therefore be regarded as a constant current/constant flux
supply.
The voltage in the secondary winding causes a current to flow through its
load and through the secondary winding. This produces a secondary flux
which opposes the primary flux and so keeps the c o r e p u to a very low
level. This is a most important point to remember because, ifthe primary is
operated with the secondary winding disconnected from its load there will
be no secondary emf to oppose the prima ry emf:
This will result in a high core flux; increased eddy currents in the core;
increased voltages in the individual secondary coils and overheating.
The result is that the current transformer will burn out. (Even if the
mistake is realised and the system is switched off before it actually burns
out, the core may be pre-magnetised, or biased, and cannot therefore be
relied upon to be accurate).
SUMMARY
1
\-
CONNECTOR
-- /
i -- '
\ \
1 _ _ -'
\ ,
I
AUTO TRANSFORMER ' I
I
STEP-UP SECONDARY
S,
, STEP-DOWN
LOAD
LOAD
6 S2 B
The output voltage is therefore that which appears in the coils across
terminals S 1 a n d S2. Loading the secondary will have the same effect a s
described for the Power Transformer. If the current flow is considered for
one particular half-cycle, it will be seen that the primary and secondary
currents a r e opposing each other in the common portion of the winding.
The actual current flow i n the common portion is therefore the difference
between t h e two currents. This means that the cross-section area of the
copper can be decreased in the common portion, bringing about a saving
in weight.
I I
The 2 8 a c~ ground service bus, feeding idterior lights, passebger signs and
service lights. ---_
.
,,
,, I i---
/ 1
I 1
'., \
I
7 - -
The iuto-transformer is also dsdd in individual circuits to s t e p down from
115 ~to /
other values of ac, typically in extei-nal lighting. 1 i
1 I 1 I
, !,
' '--
I - I
moodull l A-827
+ Peak voltage v
- 0.318 v
As the name implies this uses both half cycles of the input wave form.
Figure 32 shows diodes Dl and D2 used with a transformer, which is
A
centre tapped a t C. The point C can be considered a s neutral with
terminals A a n d B swinging alternately positive and negative about it.
i
When A i s positive to C, Diode Dl conducts with D2 switched off. On the
other half cycle of input, B is positive to C and D2 conducts with Dl
switched off. The output is therefore un-directional, with both diodes
alternately conducting, giving a full wave output across RL. The average
output voltage is 0.637 x peak (assuming no losses), ie average of the
supply -
- -
- -
Peak voltage v
AC Supply
-
-Average voltage
0.637 v
A point to note about this circuit is that when Dl is conducting, the voltage
across the load resistor RL is the peak voltage. With D2 cut off the voltage
across C-B is in series with this voltage, so these two voltages combine to
give a total of twice the peak voltage.
This will act as a reverse voltage across D2 SO the peak inverse voltage for
the diodes m u s t be twice the peak voltage on either half of the secondary of
the transformer.
Bridge Rectifier
This is also a single phase full wave rectifier, and has advantages over the
previous circuit in that the transformer does not need to produce twice the
voltage required and the secondary is in use all the time. Unlike the
previous circuit where only half the secondary winding was used a t any
one time.
!
-:
Fig. 33 BRIDGE RE~TIFIER FIRST HALF ~ F F L E
I I
' I
, - , /
/
O n the next half cycle (figure 34) assume the bottom of the secondary is
positive and trace the circuit through the load following the arrows. Note
the direction of current through the load is the same during each half
cycle, ie it is dc.
Note that in this circuit the two non-conducting diodes have twice the
supply voltage across them, (load/supply voltage + supply voltage = twice
supply voltage). However, this voltage is shared between the two non-
conducting diodes in series, therefore the peak inverse voltage per diode is
the supply voltage. As before the ripple frequency is twice the supply
frequency.
Therefore this form of rectification can only be used where there is a star
connection using a neutral line. Assume this star connection is the
secondary of a three phase (DELTA-STAR)transformer as shown in figure
35.
Figure 36 shows the waveform of the three phase supply and the resultant
supply voltage to the load.
o m
I VOLTAGE
Note t h a t the ripple frequency of this rectifier output is three times the
supply frequency; with three dc output voltage 'blips' for one sequence of
the three phase ac supply.
This form of connection does not require a neutral line, so can be used on
either Star or Delta connected systems. Figure 37 shows the diode circuit
diagram.
rnoodull l A-830
LINE
LINE
LINE
The arrows show the time in the three phase cycle when phase A is
maximum and passing peak current ti the load (say 10 amps). After
passing through the load, the current splits into two, of five amps each to
return to the B and C lines back to the supply.
,- -
- -
,
, ---
-- -- -
\.
\
'
The use of rectifiers in the systems we have covered have mainly been
three phase rectifier systems, ie in the transformer rectifier unit (TRU)
there are star/star and star/delta systems. Within a brushless generator
a three phase full wave rectifier system, and in a voltage control system a
single phase bridge rectifier system.
- 28 -
rnoodull lA-831
CIRCUIT PROTECTION
The protective device shall be of a type and capacity such as to ensure that
it will perform the duty for which it is installed, and should be capable of
sensing small sustained overloads, ignore short duration surges, and clear
the circuit as quickly as possible on short circuit.
Fuses
The minimum fusing current is the current, which will cause the fuse to
operate under given conditions in a given time, typically four hours.
Fusing factor -
- rated minimum fusing current
current rating
- 29 -
moodull IA-832
A fuse providing close excess current protection is one with a fusing factor
of 1.5 or less.
An example of a light duty fuse and its holder is shown in the next
diagram.
CAP I /
N S E RATING
/
/
--
METAL END
Pa- "
FUSE
I
-. .. .- --. .
\.
-
8
-- - - \\ -\ r--.,
I 1
1
I
I I I I /'
~ e a duty
G or High Rupturing CQsity (HRC) fuses are nqrr&ly,us/usdd for
such !circuits as main electrical distribkti'on. They consist bf a c e r d i c
tube which a.pumber of idehtlcal fusible',elements are cbnbected in
parallel to the end contacts. The tube is filled with a pacqng medium of
granular magnesite (magnesium oxide), kieselguhr or chalk
(calcium carbonate) to damp d o h t h e explosive effect of the resulting arc
whkn-rupturing takes place. --Thepaked tube is sealed at each end with
metal end caps, formed into mounting lugs, and fire clay cement.
CERAMIC BODY
INERT GRANULES
FUSIBLE INERT
ELEMENT GRANULES
CERAMIC BODY
\
Current limiters are used mainly for the protection of heavy duty power
distribution circuits a n d consist of a high melting point single strip of
tinned copper shaped a t each end to form mounting lugs. The central
portion of the strip is, in some cases, "waisted" to form the fusible area. It
is enclosed in a ceramic housing which has a glass or mica window in the
side to allow for visual inspection of the fuse element. The timelcurrent
characteristic of the device will allow a considerable overload current in the
circuit before rupturing occurs, and are therefore useful in circuits
carrying occasional current surges, such as starter motor circuits.
GLASS
The Air Navigation Order lays down that spare fuses, for all electrical
circuits, which can be replaced in flight, must be carried. This is 10% of
the number of each rating employed or three of each rating employed,
whichever is the greater.
moodull lA-834
SHORTING LIMITING
BATTERYRELAY STARTING RELAY RELAY RESISTOR
BREAKER
SWITCH '1y
L ---
-
Fig. 42 STARTER MOTOR CIRCUIT
--\
c- - -
( r - - - . \'
Cwrent to the motor is now limited by the bemf of the motor. When the
engine reaches 'self-sustaining' speed the starter motor circuit is switched
off.
Circuit Breakers
Disadvantages of the fuse are that it takes longer to replace than to reset a
breaker and spare fuses have to be carried for in-flight replacement.
All manually operated circuit breakers used on aircraft must be of the "trip
free" type, ie they cannot be maintained closed or held against a fault
current when any part of a circuit is carrying overload current.
Figure 43 shows a typical manually operated circuit breaker. Manual
operation is usually by means of a single push-pull button, pushing to
close the contacts, pulling to open.
t I
LOAD A SUPPLY
I In figure 44(a) the normal circuit current passes through the main
contacts and bi-metallic (thermal) element. Should a fault occur causing
the current to exceed its normal value, the bi-metallic elements curvature
will change (caused by the difference in the coefficients of expansion of the
materials).
The main contacts open to disconnect the generator from the busbar when
the latch assembly is released; this action is performed by the
displacement of a trip lever, which in turn is operated either manually (by
pressing the trip button), by remote control through the attracted
armature electromagnet system, or automatically when a reverse current
condition, of sufficient magnitude and duration, develops in the single turn
coil. After tripping by any of these methods, the circuit breaker must be
reset by operating the setting handle.
RUBBER SHROUDED MANUAL TRlP BUTTON
SETTING LEVER
TERMINAL TO
TERMINAL TO
GENERATOR
1 I BUS BAR
MANUAL TRlP
PUSH BUlTON
The single turn coil shown in figure 46 is located over a soft iron yoke
provided with pole faces between which is pivoted a permanent magnet
armature. With current passing through the single turn coil a magnetic
field is established between the pole faces of the soft iron yoke. Polarity of
this field (and hence the direction in which it tends to displace the pivoted
permanent magnet armature) is dependent on the direction of current
through the coil.
The polarity of the yoke field, with current passing through the single turn
coil in the normal direction, is such that the armature takes u p a position
in which one of its arms is poised above an ext,ension of the trip lever.
While the other end lies immediately below, and just clear of, a setting
lever. The same position is maintained by the armature when there is no
current through the single turn coil.
With a reversal of current in the coil the polarity of the yoke field is also
reversed, and a force tending to deflect the ends of the pivoted armature
towards the trip lever extension and the setting lever is established.
the escapement allows the armature to turn quite slowly until; after a n
appreciable delay, it displaces the trip lever. This unlocks the latching
assembly and so permits the spring-loaded contact assembly to open.
If the reverse current is not sustained and falls to less than the designed
minimum trip value before the permanent magnet armature, restrained in
its movement by the escapement, has been able to operate the trip lever,
the armature is returned to its original position and no trip action takes
place.
- 37 -
rnoodulll A-340
LBP Dec 03,Feb 04, April 04, April 07
***
Hand held fire extinguishers - numbers on aircraft. EASA25 states a t least 1
on the flight deck and in the passenger (pax) compartment 1 f7 to 30 pax), 2
(31 to 60 pax) and 3 (61 or more p e ) minimum.
---
NOTE: It is possible that some of the above statements may not be too
meaningful when read out of context, so it is suggested that the appropriate
book/subject be read first then the information above be checked against that
topic.
CONTENTS
Page
The cabin is the only area the passengers get to see. They tend not to bother if
something technical goes wrong (though often they are not told), but if something
fails in the cabin, like the In-Flight-Entertainment packs up, or the galley ovens
fail then passengers get disgruntled very quickly.
Cabin appearance (decor)is also important to the passenger. If the cabin looks
good it is assumed the rest of the aircraft has been well cared for - though that is
not always true.
The design of the aircraft and its equipment (by regulation) h a s to take into
account many emergency situations - such as:
-k
Fire (and smoke) within the cabin (fire extinguishers - smoke hoods -
*
-
slides).
- .
-
firelsmoke detectors - fire proof materials for seating - floor path
lighting etc).
Emergency evacuation on-land-,(ropes/rope ladders escape -
Note that all these have one thing in common - in a normal situation they are not
- -
Regulatory Requirements
These change from time to time but you need to be aware of them and where they
are stated. Currently the information regarding the carriage of equipment is laid
down in the Air Navigation Order 2005 (ANO).This publication i s dealt with in
detail in module 10 Air Law. Briefly it states:
An aircraft shall not fly unless it is so equipped as to comply with the law of the
country in which it was registered. The equipment carried must be clearly identified
and be so positioned to be able to be used by the person for whom it is intended.
The scale and quantity of equipment to be carried varies between the size and
function of the aircraft and the terrain over which it is operating. Large
commercial air transport aircraft have to carry the most extensive range. You
need to bear in mind that not all aircraft need to have all this equipment fitted, so
you should consult the A N 0 and Airworthiness Notices (ANs) and CS25 and 2 3
(downloadable free from www.easa.eu.int) for details.
In general the Certificate Specifications for aircraft (not including rotorcraft) are:
A CS-VLA Single engined piston (diesel or spark ignition) aircraft
with not more than 2 seats and not more than 750kg
maximum certified take-off weight.
* CS23 Normal, utility, aerobatic and commuter aircraft.
Maximum seating, excluding pilots, for normal, utility
--
and aerobatic aircraft is 9 and maximum weight is
5670kg. It states that commuter aircrafttare propeller
I
driven <win engined aircraft with a m d m u m passenger
seating of 19 and a weight limit of 8618kg. C 3 2 3 includes
specifications for piston engines, turbo jet and turbofan
engines!
* CS25 Turbinei powered large aircraft.
I r--- - I
In general CS25 states that the ;oliowing equipment is to be f;ltted to aircraft when
flying for the purpose of public t!-ahsport:
I '
1 ;
1 Crew segts (flight crew anh cabin cr&w)must have multi-doint safety
harnesses - unless allowed otherwise by the CAA.
2 Passenger seats (which may face in any direction) - lap straps (or lap straps
with a shoulder strap or a full harness) on all seats, with a child restraint
device for any child under the age of 2. A means of indicating to the
passengers that belts are to be worn. Seats must be designed to take a 77ko
person.
3 A life jacket for every person on board - when flying over water more than
gliding distance from land.
4 Life rafts sufficient for all persons on board for aircraft capable of carrying
20 or more people - if flying over water more than a certain flying time from
an airfield where a landing can be made.
5 Additional floatation equipment for 1/ 5th of the total occupancy - for
manoeuvres over water.
6 A first aid kit - security sealed, to contain a minimum specified list of
equipment sufficient in size for the number of passengers.
7 Public address system.
8 Smoke hoods for all the crew.
9 Portable battery powered megaphone.
10 Means of escape from the cabin (slides or ropes) - if the sill of any
passenger door is more than 1.82m from the ground in any state of
undercarriage collapse. Rope and attachment strength to be not less than
1779N.
11 Portable fire fighting equipment and gloves.
12 Torches.
13 Appropriate survival equipment if flying for long periods over uninhabited
tropical/polar regions.
14 Cabin escape routes to be illuminated and emergency exits signed. Supply
to be independent of normal electrical supply and, when armed,
automatically activated if normal lights fail or aircraft is put through an
impact of more that 2g.
15 Number, location and size of aircraft exit doors and escape hatches are
specified. Must be openable from inside and outside the aircraft and clearly
marked.
16 Any birth or litter must have a restraint system and withstand certain
minimum inertia loads.
17 Baggage and cargo areas-must-be placarded to show maxlmum -
weight
contents critical load distribution.
18 Maximum burn rates are specified for cabin materials.
19 If the commander cannot see all the passengers, a means of indicating to
the passengers that belts are to be warn (an illuminated sign).
20 All passengers must be able to escape within 90 seconds in a n emergency
with aircraft on the ground. i
# I
LIFE JACKETS
The A N 0 states that on public transport aircraft flying beyond gliding distance
from land there must be one for each passenger and all the crew (demonstration
jackets not counted). The jacket should be accessible from the normal seated
position.
-3-
rnoodull l A-845
Fig. 1 CABIN EMERGENCY EQUIPMENT - EXAMPLE
Usually stored under the passenger seat, but sometimes stored in arm rests and
within Velcro covered panels close to the seat. The location of the life: jacket must
be clearly placarded. The jacket must have a whistle and a waterproof lamp. They
are lifed from manufacture or overhaul (also the CO:! bottle), with a typical period
being 6 years.
Equipment includes:
* A whistle (for children under three this need not be fitted).
* A water activated cell that operates a light.
* A COz bottle for inflation purposes - with a pull chord for
operation.
x An inflation mouth piece.
* Straps for tying around the body.
* A spray hood (not always fitted).
All work carried out (by an approved organisation) on lifejackets must comply with
the appropriate manufacturer's instructions (repairs, replacements, etc).
An inspection record with all the particulars of the lifejacket including details of
mandatory modifications and inspections and the inspectors stamp and
signature, should be kept a t the maintenance base. The lifejacket should be serial
numbered to identify it against it's record. --
- -
PROTECTION
COVEA
@<x
{ .% 1-
"JERK TO'INFLATE"
TAG
-5-
moodull l A-847
A standby mouth inflation valve is also provided should the C 0 2 system be
inoperative or the jacket requires topping-up. Deflation can be achieved by
depressing the NRV in the mouth-piece.
To assist search and rescue the jacket is equipped with a light and water operated
battery. Some jackets may also carry additional equipment, eg fluorescent sea
marker dye; shark repellent; signalling devices; rain and sea-spray hood, etc.
Lifejackets are packed in nylon or plastic valises and instructions on their use
must be displayed in the cabin and on the jacket.
Inspection
I
--
r-
~nspec'tidnsshould be carried oyt f n cld& premises on smooth bork surfaces.
The plastic material of the jacket and the webbing of the strapsshould not come
into contact with oil, grease, or acid. I
I
rnoodull l A 3 4 8
Inflation Test
This may be done by pressurising the jacket (to a very low pressure) and checking
the pressure drop over a period of time or immerse it in a clean tank of water and
check for bubbles or use a n acid free soapy solution.
Repairs
Minor damage may be repaired if an approved repair scheme is available. The area
of the leak may be marked using white chalk only - this to be removed after
repair. Repeat inflation test.
A first aid kit must be carried and it needs to be security sealed. May contain
specialist resuscitation equipment. The first aid kits can contained controlled
drugs and care needs to be taken where they are located.
The kit must contain bandages and other equipment (aslisted in the ANO), the
quantity relating to the number of passenger seats in the aircraft.
Equipment for the protection of eyes, mouth and nose (CS25 and the ANO) for a
minimum period of 15 minutes. ... .
The crew only (at present) are provided with smoke hoods. ~ h e s ea, s with life
jackets, need to be easily accessible from the normal crew station. The smoke
hoods are contained in a box and are also lifed from manufacture or overhaul.
The purpose of the smoke hood is to cover the eyes and nose and mouth of the
crew to allow them to help passengers in an emergency.
Most crew emergency oxygen masks incorporate a face mask (smoke hood) to
cover the nose and mouth.
MEGAPHONE
rnoodull I A-849
The megaphonels need/s to be mounted securely in a clearly identified location.
I t needs to be able to be removed easily by the crew. Periodic testing and renewal
of the batteries is the only maintenance required.
- - -
Both water and BCF extinguishers will be found in the aircraft cabin. These are
for crew use only. They will be clearly identified with water in a red container and
BCF is usually coloured green. (Note. BCF is currently causing concern because
its adverse affect on the ozone layer and current EU regulations for ground based
extinguishers is to have them all coloured red with only a small square of the
appropriate colour showing).
rnoodull l A-850
Operation of the bottle is required to be by a single handed operation. It is
removed from the bracket, the safety catch is pushed up with the thumb, it is
aimed at the fire and the trigger squeezed.
The bottle itself h a s a 'full indicator' disc, which is pushed out as the trigger is
depressed, giving indication of a partially (or fully) discharged bottle.
The cabin crew will make an appropriate entry in the log to inform the engineers if
the bottle h a s been operated. It must then be changed. In any emergency
situation where bottles are likely to be used they should all be checked. Normally
checked by weighing, but some bottles have a pressure gauge with green and red
indicator segments. Some have a 'test soft spot' usually on the bottom - if this can
be pressed in with the finger the bottle needs changing.
With reference to figure 4. The transit pin should be fitted whenever the bottle is
being moved for maintenance purposes. It is important that it is removed after
fitment to the aircraft. When fitting, also check that the extinguisher fits into the
bracket in such a way that the bracket trigger guard or lug fits so as to prevent
inadvertent firing of the bottle whilst in the bracket.
- 9 -
rnoodull l A-851
Bottles should be weighed periodically as laid down in the approved maintenance
schedule. It is also checked for damage, that the transit pin i s removed and that
the full disc or fired indicator is still in place. The life date should be checked.
The bracket will require inspection whenever the bottle is removed to ensure it is
not damaged or corroded a n d that the quick release mechanism functions
correctly. As with all emergency equipment fire extinguishers need to be clearly
labelled a n d are located near to normal crew stations.
Next to the extinguisher you will often find a pair of fire gloves.
The numbers of hand held fire extinguishers required as stated in EASA CS25
are: --
For more information on hand fire extinguishers see the book in the -LBP series
module 7 entitled Safety.
ESCAPEROPES
If the door sill of a n aircraft is higher than 1.8m (6 ft) from the ground in any
configuration of undercarriage collapse, a n assisted means of escape has to be
provided. For flight deck crew this normally consists of a retarded rope system, or
rope ladder.
ESCAPE
ROPES
-
ESCAPE
ROPE
The rope assembly is securely fzed to an anchor point normally-above the escape
window. In an emergency the free end of the ~ope/ladderis removed from its
stowage and deployed to hang out of the dv (direct vision) window, the crew climb
out of the dv window and climb down the ladder or are lowered slowly by the rope
retard mechanism in the rope deployment unit. -
-.
.- -. - ---- -- ..
Minimum number and location of emergency exits are specified for the flight deck
to include, in some cases, exists above head height.
Some aircraft have inertia escape ropes which lower the person to the ground. The
pilot holds onto the rope handle and starts to descend. A s the rope is deployed it
turns paddles within a small chamber filled with hydraulic fluid. This has the
effect of slowing the descent rate to an acceptable level.
Periodically these units must be removed and the ropes and inertia units checked
for damage, security and operation. Weights are used to check the rope
deployment rate).
moodull l A-853
Fig. 6 SLIDE/RAFTS DEPLOYED AFTER DITCHING
moodull 1A-854
ESCAPE CHUTES/ SLIDES
For passengers the normal method of emergency escape is the self-inflating slide.
Often called a slidelraft it inflates automatically when the doors are opened in the
armed emergency mode. On many aircraft the slide doubles as a life raft in that
once inflated on a ditched aircraft it will float on the water and can be detached
from the aircraft and used as a raft.
GAS
TLIDE ASSY.
Normally
-- housed
-
-. - within the decor panel of each door (though some are housed in
a container next to escape h a t c h e s ) : - ~ i ~ r6e and
s 7 shows the rafts deployed on
water and land. Typical stowage examples are shown in figures 8 and 9.
When the door is opened the slide is caused to operate (door operation is covered
in the book entitled Structures 1 in this series).
The unit consists of a gas bottle with some aircraft having an air charged bottle a t
3000psi (21MPa) and others having a nitrogen charged bottle a t about 3,500psi
(24MPa). The bottles are fitted with pressure gauges that can be seen when the
slide is packed.
On operation the compressed gas passes into the slide tubes via an air aspirator.
This draws in extra air from the atmosphere (slide tubes have a capacity far too
great to be inflated by any reasonably sized gas bottle alone). A pressure relief
valve is fitted to prevent the slide over-pressurising and a fusible plug is fitted to
the bottle to prevent the bottle bursting due to excessive heat.
Slide illumination is provided automatically when deployed and the slide itself is
neatly and carefully folded into the packboard and laced up.
ESCAPE SLIDE
Operation
I
O n older aircraft a member of the ,crew would' lift the girt b a r o u t of its stowage
position on th,e door a n d lock it into the floor brackets (figure111)before t h e door
is opened. When t h e door is opened (outwards) the slide pack would move with
t h e door a n d t h e slide would be-pulled out of its pack a n d its falling weight would
trigger t h e inflation bottle.
With the door armed (arm/dis-arm lever on the door moved to t h e armed position)
a n d the door release lever moved to open, the door lock bolts/catches disengage
and, with gas assisted doors, the door opening jack pushes t h e door open. The
girt bar (girt bar a n d top end of slide) is attached to the floor a n d the slide itself i s
attached to t h e door.
The action of the door opening pulls on the slide pack a n d releases t h e
lacing/Velcro which allows the slide to fall from the packboard a n d h a n g outside
from the aircraft floor. The action of the slide dropping out of t h e door pulls on the
bottle actuation cable a n d operates the firing disc inside the bottle. The bottle
discharges through the aspirator. This inflates the slide by sucking large
quantities of air from t h e atmosphere into the side tubes.
HARNESS
ATTACHMENT
TO DOOR
HARNESS
PRESSURE GAGE
LOWER SHELF
PACKBOARD
ESCAPE SLIDE
moodull l A-857
- - -
- -- ~-
,~-
LANYARD
, 1I
L--, ,
,
\
\
,
, ,
I I . ,
1 1
I
Fig.\ 11 GIRT BAR 0PERA;ION - OLDER AI~cRAFT
I
Figure 12 shows the deployment olf-the-slide based on the Boeing 757. The slide is
a two tube slide, for added rigidity longer slides are four tube slides - two on each
side one above the other. Slides have emergency lights positioned along the top of
each tube which come on when deployed.
blank
ESCAPE SLIDE
NO. 3
EMERGENC'I
=IT DOOR
WOR
CUTOUT
NO. 3 EMERGENCY
Most aircraft have a system of levers and push/pull rods to engageldisengage the
girt bar. The arm/disarrn lever on the door moved to arm will cause either the girt
bar to 'extend' out either side of the door to engage with locking fittings on the
aircraft floor at each end, or to move a locking latch from the door to the floor
fittings.
RELIEF
--ASPIRATOR
I N F L A T E D S L I D E I R A F T CROSS S E C T I O N
(SCHEMATIC) P R E S S U R E GAGE
SAFETY
I
, , I
1
I I
-
CONDITION : Armed.
show disarmed
Figure 14 shows a girt bar locking system using sliders that effectively extend the
bar's length. Shown in the armed position with both sliders out and engaged with
the floor mounted lock fittings. When the door opens (in the armed state) the
operating mechanism moves with the door - complete with the slide pack, leaving
behind the girt bar which has attached to it the girt (the top part of the slide).
The arrows indicate the movement during disarm when the sliders are pulled out
of their floor mounted lock fittings.
Figure 15 shows how the door operating mechanism moves away from the girt bar
when the girt bar is engaged and the door is opened.
, Most modern aircraft use slides as life rafts, with inflatable canopies provided in
the emergency kit. If this is not the case separate life rafts are provided. These are
normally located by the doors, often in the roof space immediately above each
door.
PERATING MECHANISM
FLOOR MOUNTED
LOCK FITTING ith slider attached to floor)
w
Fig. 15 GIRT BAR ENGAGEMENT DETAIL
Study figures 16 and 17 re the flight deck indications. Note the use of
magnetically operated proximity switches using a 28V dc supply and using the
switches on the earth side of the circuit. Note also that this signal will be sent to a
Symbol Generator Unit (SGU) to produce a colour display on the flight deck
CRT/flat screen display.
blank
1 ' ENTRY AND
ATTENDmTs LIGHTS 1-
RIGHT BUS
n rp
GIRT BAR I1L'I
PASS. DR
I-
PASS. OR
PROX SNSR A PROX SNSR B
PASS. OR,
GlRT BAR
\
ANN. LIGHT
TO OTHER
PASS. DR
GlRT BAR
ANN. LIGHTS
Maintenance
In-situ checks will include checking for correct operation of the armldisarm
mechanism; correct operation of the door opening mechanism (ONLY in the
dis-armed condition); correct clearance between chute container and fuselage
when opening the door; correct bottle pressure; bottle transportation pin removed;
any flight deck indications; damage and security of floor mounted girt bar locking
brackets; security of pack to door; security of any lanyards a n d correct
lacing/Velcro attachment on chute packing.
Maintenance tasks will include removal for inspection and periodic lifed item
changes. Whenever this is the case the slide is deployed to prove serviceability.
Care needs to be taken during these type of activities to prevent injury or damage
as the door will open fast and the slide deploy violently.
The slidelraft is subject to vibration, creasing, and general deterioration and the
nylon fabric should be inspected periodically for:
* Cuts, tears and damage.
* Chaffing and hardening.
* Legibility of markings.
* Security of attachments, ropes, etc.
* Security of seams and leaks.
* Lights for correct operation.
Check all metal fittings for correct operation, corrosion, damage, cracks, and
, security of attachment. Check all indicating systems (study figures 16 and 17 for
--
Check all internal stores (drinking water bottles, flares etc) (raft). Check water
activated battery for security of attachment and signs of moisture ingress (raft).
At the periods stated in the maintenance schedule the slide should be removed for
overhaul. This will involve a functiond test and pressure test. A full functional
I
test (automatic deployment) should be carried out at least every; 36 months and
the test must be videoed (AN12)'(AN = Airworthiness Notice). ,
Each type of slide must have its own servicing manual and maintenance bays
should have the correct facilities including smooth topped work benches. Each
slide should have a record.
The Fabric
Originally neoprene proofed nylon coloured yellow. To comply with FAA TSO-C69A
chutes are now made from polyurethane proofed nylon coloured silver on the
outside.
Used Escape Slides
These should be returned to the manufacturer with a report on why they were
deployed. Training escape slides (for cabin staff and air crew) should be marked
accordingly and not used for anything else.
Storage
Slides should be stored deflated in their original containers with transit pins
fitted, and lightly dusted with french chalk. Do not store more than 3 on top of
each other. Temperature should be between 15 to 2 1°C; dry atmosphere; free from
dust and fumes and out of direct sunlight.
The stored slide should be inspected every 18 months and inspected prior to
fitment to the aircraft.
Repairis
1 -
Some parts of the, slide are not repairable. Refer to the manufacturer's literature.
I
Repair: kits are available. I
I
When the aircraft is on the ground with any sill more than 1.8m from the groun"
in any state of landing gear collapse then an assisted means of escape must be
provided to allow all passengers to evacuate within 90 seconds. For passengers
this is an inflated slide which must:
* Inflate in 10 seconds.
* Inflate in a 25kt wind and be held stable by no more than one person.
* Be a double slide at type A exits.
Where overwing emergency exists are provided then inflatable wing walkways
must be provided and inflate within the same time period.
Where the passenger first lands on the ground that area must be illuminated to 3
lux (3 lumens per square metre) or more. The lights are normally fitted to the
slide.
rnoodull l A-864
SAQ I
Prior to refitting a slide pack, what inspections should you carry out?
Requirements
The CS25 structural specifications of the aircraft include the requirement that,
provided the aircraft lands reasonably intact in the water, it should stay afloat
long enough to ensure sufficient time to evacuate everybody to life rafts.
The A N 0 states they should be fitted to public transport when-ever the aircraft
flies over water more than a certain gliding distance from a n airfield. It also states
that equipment is to include:
x
- -
Weather protection.
* A sea anchor. Prevents the raft being blown too quickly over the water
with a wind blowing.
* Attached life lines and tow lines.
* Paddles, water proof torch, pyrotechnic distress signal flares, a
quantity of fresh water (or provision to convert sea water to fresh
water), some glucose tablets and radio survival beacons
- (numbers
depending on the raft numbers).
The quantity (specified in CS25) must be sufficient for the seating capacity of the
aircraft with sufficient spare to cope with the lose of the largekt raft. They should
be stored near the exits and if s t o r ~ o u t _ s i dand
e released remotely must be
attached by a line to the aircraft. The raft line to be easily detached.
CS25 further states that, if the aircraft is not certified for ditching, then there is to
be sufficient approved floatation gear (approved seat cushions for example) for the
seating capacity.
If the escape chute is deployed with the aircraft in the water then it will convert
automatically to a life raft. It can be detached from the aircraft and, to comply
with the ANO, it must be fitted with additional items of equipment.
If the normal exit cannot be used the chutelraft must be capable of being moved
to another exit, attached to the aircraft then lowered into the water and inflated.
When evacuation into the raft is complete the mooring line to the aircraft is
releasedlcut (a tool is provided on the raft).
In normal emergency operation the slidelraft (as a raft) is armed, the door is
opened and the slidelraft deployed. Once deployed two handles are pulled,
marked RAFT DETACH - PULL. This action extracts two locking pins which
detaches the chute from the aircraft - except for the mooring line.
LIFE RAFTS
Figure 18 shows a typical life raft. The raft should be packed in a stowage such
that it can be inflated easily by the crew or the passengers, and is accessible from
an exit.
The life raft pack is inflated by pulling a lanyard which operates the valve to allow
the COz bottle to discharge into the raft buoyancy chambers. The life raft, which
is attached by a line to the aircraft, will inflate together with the canopy. Lines
and rope ladders will allow passengers to get inside the raft from the water.
.
7--
The floor is double lined for warmth arid axrain water catchment system is
-- -
provided. I , I
\
i
By regulation life rafts should: I
1 %
I /
Maintenance
Additionally check all internal stores such as drinking water bottles, flares etc.
Check water activated battery for security of attachment and signs of moisture
ingress. Check voltage output - it should be zero.
RAINWATER CATCHMENT
INTERIOR LIGHT TUBE(S)
LIFELINE
1 &QUOIT
(inside)
\
PAINTER
\ .lsE I N F L A T O N CYLINDER
PATCH
--
\
CANOPY DOOR(S)
Any defects of cabin emergency equipment are serious a n d are covered under the
Mandatory Occurrence Reporting (MOR) scheme.
Study figures 19 and 20 and note the operation of fitting on oxygen masks (more
about oxygen systems in the book entitled "Cabin Air Conditioning and
Pressurisation"), life jackets, opening of doors and the general deployment of slide
rafts a n d rafts.
Fig. 19 PASSENGER SAFETY PLACARD - 1
Note. A n aircraft can fly with a door slide inoperative provided it is allowed in thr
MEL; that the exit it is clearly marked NO EXIT; that the pilot is informed and th,
passenger capacity reduced.
blank
S~artundL.Munp ~~blrraum.r( Nol.usgang
4 ~~y,;:;bdlno NO mklno
~ . p l rium, EXIT E-,p.ncl ell,
~ o n ~ a ~ s e c o ~ , ~
NOIYIIIII S*lld.d. ulgencia
H1olurn.r 5.161 a ~ r r n e ~ p & n ~ . ~
h~collgern. NWI tumara UICIII a, ~m(cOlnr.
atartisu~psm ../mksa mxattvn
Decollo. an.n.ggio A ~ p i m u o.um
i
-
H . r r ~ ~ b
m.m/#mnaa ~ i wlnt
o w~<cm.zapav~-t
Ow.--- Zabr.nlano Dutilt 1zIuIlnula~
sun I l,ao*mi. A"-rGnot 'Uobo<c~rburou
SI.rllsp~tllnje t
0 -
v T.hlik~c~h ~~
kap,,,
P,c&vqm SIQM ~gilmal .PflUCI++
+='ti.
Kalkq YC ini*
+A'J
t.Yn
1
EXIT
1,2,4
EXIT
3
Emergency Lighting
The A N 0 scale Z requires that sufficient lighting be provided both inside and
outside the cabin to facilitate the safe evacuation of the aircraft in an emergency.
This to be operable in the event of normal electrical supply failure.
rnoodull IA-869
It (and CS25) requires emergency floor path lighting in the passenger cabin
sufficient to allow evacuation of the aircraft in the dark or in smoke conditions.
These lights may be fixed to the bottom part of the seat structure next to the aisle
or fixed to the floor. On some aircraft they are also fitted around escape hatches.
emergency exits. \ \
[ I ,
C - '
ELECTROCUHINESCENT STRIP
(BONDED TO FLOOR PANEL)
FLOMI PANEL
rnoodull l A-870
Figure 21 shows typical floor mounted emergency lights, powered from the
essential dc b u s with a dedicated emergency battery back-up.
For more information on lights you should refer to the book in this series entitled
Lights.
Exercises:
1. What is the minimum door sill height above which emergency slides are
required?
2 . Must a n aircraft have a separate life raft?
3. Do all life jackets have whistles? If not why not?
4. What are the requirements of a megaphone?
5. Where are fire gloves kept?
6. How are hand held fire extinguishers prevented from inadvertent operation?
7. Look a t the emergency equipment on your aircraft. Make sure you
understand how it works - using the manual if necessary.
8. Check the scales of equipment in the Air Navigation Order (if you have
access) for equipment to be carried and see how your aircraft compares.
CABIN GENERAL EQUIPMENT
SEATS
* Crew seats
* Passenger seats
Crew seats c a n be further sub-divided into flight deck seats and attendant seats
and passenger seats can be sub-divided into main cabin, business class a n d first
class seats.
Figures --22 & 23 show typical flight deck seats. Equipment includes: -- --
' . -
* A five-point harness (&-figure 22 the upper two points are not
actually show, b u t will1 be their). I t h a s a n inertia reel style of belt and
has the option to lock the inertia reel in position., (Inertia reel belts
u s e a small lead mass to move a locking pawl intp gear. This may be
operated by the forward--movement of the pilot a n d l o r the
' deceleration of the $reaft). ' --
I '
i i
* ~aterd and verticalsqat adjustment to ensure the crew member is
conifortable a t the qontrols. , I I
-
Maintenance
Belts. Check belts for security, wear, damage and correct operation of quick
release mechanism. Sit in the seat, strap yourself in and lean forward - the
release mechanism should release without too much force.
O n inertia reel type belts check the inertia reel by giving the belt a quick tug and
it should lock. Check the operation of any manual locking and any ratchet
mechanism. Check belt webbing for fraying - include all the webbing down to the
inertia reel unit.
BACK CUSHION
OVERRIDE
(HORIZONTAL)
Initial reel assembly. Check for security, damage and correct operation. If the seat
does not have an inertial reel assembly check the quick release mechanism and
ensure that it allows the belt to ratchet back into place. The shoulder straps are
fitted to the initial reel assembly sometimes by a cable - check it is not frayed and
runs correctly over the seat top pulley or roller.
Structure. May be made of aluminium alloy tubing with riveted, bolted or welded
joints or machined sections bolted together. Check for damage, corrosion and
security. Check seat security to the floor. If the seat slides in floor runners check
these for damage, corrosion, wear and cleanliness. Check all seat adjustments for
full and free range of adjustment and check that in each position it locks securely
in place.
blank
m, HEADREST
SHOULDER
HARNESS
BUCKLE
LLRIBAR
REST
ABOOHINAL
BELT
SIDE STICK
AiVII1EST
SLEEVE
COLUIW
Fig. 23 ~ 3 3 FLIGHT
0 DECK SEAT
I
1
~ -
/'
-1
HEADREST CUSHION
SEAT CUSHIO
BACKREST CUSHION
SEAT STRUCTURE
STOWAGE
COMPARTMENT
DOOR
SEAT TRACK F I T T I N G
Seat electrics. If the seat is electrically adjustable check that all adjustments work
correctly. Check motors and cables for security, damage, signs of overheating and
contamination.
Cushions. Check for damage, cleanliness, security and check that they are dry.
Check with the seat in the forward most position, that the cushions do not foul
the controls.
Cabin Crew Seats
These are usually located near the main aircraft exits (by regulation the seated
attendant must be able to see the passengers for which he/she is responsible and
must face forwards or backwards) and will fold up out of the way automatically as
soon a s the person gets up. They will be either forward or aft facing and
depending on this depends on how strong they are, the forward facing ones being
stronger.
- - -
In figure 24 the area under the seat is used for stowage of emergency equipment.
There may be a 'phone attached to allow the attendant to communicate with the
flight deck or another flight attendant station.
Inspection of these seats follows a similar pattern to other seats. One additional
test is carried out to check that the seat pan folds correctly and unaided (normally
sprung loaded). If the seat pan was to remain down it would cause an obstruction
to an emergency exit.
Passenger Seats
For larger aircraft these generally have more equipment fitted to them and can
vary considerable between operators and between the class of the seat - main
cabin (economy class), business class and first class. Seats may face in any
direction and can fold forward except those a t exit aisles.
Figure 26 shows a seat assembly that you might expect to find fitted in first class
cabins/ business class cabins.
ADJUSTABLE L I D I N G HEADREST
HEADREST WINGS
BACKREST W I T H
LITERATURE PACKET
ADJUSTABLE
LUMBAR SUPPORT
FIBER-OPTIC
TELEPHONE, PCU READING L I G H T S
AND GAMES HANDSET
--
ASHTRAY----,
V I D E O PLAYER
R U B S T R I P AND
L I T E R A T U R E POCKET
T I L T I N G SEAT
P I V O T OUT
C O C K T A I L TRAYS
I
a V I D E O MONITORS
' L I F E J A C K E T STOWAGE
SELF STOWING
FOOTREST
\
FOLDED F O O T
SUPPORT \
BARS
rnoodull l A-876
The seat is clamped to the floor seat tracks (figures 31 and 32). Each track is a
hollow extrusion with a series of holes in it a t 1" (25mm) pitch. The seat locating
lugs a r e placed in through the holes in the track then moved %" (12.5mm)
forward to allow the feet of the lug to lock into place. A locking tab is provided
which prevents the seat from moving forwards or backwards once locked.
FOLDING
BACKREST
FDLOING
TABLE
PASSENGER SEAT ~ ~ L E ~
m
mrm
( R - - -
m SEATLOCKAELEGE LEVER
-\ I '
\
/
nw
YWRUaW I !
--
-'/
Fig. 3 1 TYPICAL SEAT -.SEAT TRACK CONAECTION
~
I
~
I
I
-
-- -
-
U N I T (TYPICAL)
SEAT ELECTRONICS
U N I T (REF)
ZONE 1 SEAT GROUP
(TYPICAL)
SEAT TRACK COVER
/
INTERSEAT CABLES
I N RACEWAY
* Adjustable reclining backs - in general main cabin seats will only recline a
little way whilst business class will recline almost to a 1;ecumbent position
and first class will go all the way down to make a bed. Arm rests may fold
u p out of the way on main cabin seats. --
* Life jacket.
* Document pocket - containing the mandatory safety noticels.
* Chemical oxygen generator - fitted in the backs of seats for the passenger
behind (rare). - - ,
* Flat screen displays for IFE positioned in the back of the seat for the
passenger behind or on adjustable arms folded into the arm-rest or spaces
between the seats. Folded screens come on automatically when unfolded.
* Floor path lighting. Some seats have emergency lights fitted low to the floor
illuminating emergency escape routes.
* Ashtray. Mandatory that it has a lid.
* Electrically powered adjustments for tilt, recline, leg support etc. M a n seats
are manually adjusted.
* Folding drinks tray.
* Floor level luggage rail - fitted near to floor level to prevent any luggage
under the seat moving forward in severe braking conditions.
* Power supply for a laptop computer.
Berths
Fitted to long distance aircraft for the use of a "slip crew" or fitted for medical
reasons. Of simple construction meeting current EASA fire and safety regulations.
The fire regulations are the same a s seats and class B and E cargo compartments
(refer to the book in this series entitled "Structures - 1").A test flame is applied
for a period of time and when removed the flame on the test material should go
out after 15 seconds. For seats etc three test samples should be used.
The berths may be contained in a small 'bedroom' on the aircraft. On large there
may be one bedroom for flight crew, often behind the flight deck , and another for
cabin staff, sometimes a t the rear of larger aircraft above the cabin ceiling u p a
short set of steps.
SEAT BELTS
Seat belts (and seats and berths) have to comply with the strength requirements
( A N 0 and CS25/23) of holding a person of 1701bs (77.lkg) safely in various
directions of aircraft movement with a safety factor of 1.33. For example, the seat
and belt should be capable of holding a 1701b person at a 9g forward acceleratir
of the body (as would happen in a crash landing) with a 1.313 safety-factor. F r o n ~
-
A N 0 ( ~ c $ eB) states that a safety belt/hAness is required for all crew' and
passenger seats and special chiid restraiqits for each child under 2 years of age.
EASA !25/23 deals more in terms of the design features of the belt, and includes
such things as: ~ ---
' \
1I --
1 I
A The belt strength. 1I 1 I
These vary in design but must conform to CAA/EASA regulations to restrain the
pilot in all foreseeable emergency situations. The drawing shows a five point
harness with the fifth strap between the pilot's legs. The two shoulder harnesses
pass up over rollers a t the top of the seat back to inertial reel assemblies either
near the head restraint or at the bottom of the seat back.
On some seat assemblies the two straps are stitched to a single strap which
passes around the inertial reel, on others each strap passes over the reel
assembly separately.
The harness consists of a shoulder harness assembly, right and left hand
abdominal belts, centre strap, release buckle, a harness reel and an operator unit
assembly.
- 38 -
rnoodull l A-880
The straps are made of nylon webbing. The reel strap or shoulder harness is
attached at one end to the harness reel, and at the other end to a metal fitting.
Plug in type buckle fittings are stitched to the ends of all the straps except one.
This h a s a permanently secured release buckle attached.
Abdominal and centre straps are fitted with body pads and adjustable buckles.
SHOULDER HARNESS
CAN BE REMOVED
UITHOUTREHOVING
ABDOMINAL BELTS
--
--
ABDOMINAL
BELT
SHOULDER
HARNESS
CONTROL
LEVER
The release buckle is a cylindrical housing in which the plug-in fittings of the
other straps are inserted and automatically secured.
The belt mechanism will allow the pilot to move forward (to reach a switch on the
instrument panel). On older assemblies this is achieved by the operation of a
release handle on the seat arm. When the pilot moves back the harness reel
mechanism will "ratchet" the pilot back into position.
On inertial reel assemblies the pilot is allowed to move forward without the need
to operate a lever. The inertial reel will lock (depending on type) when either the
aircraft slows down too quickly or the pilot accelerates forward too quickly. (This
can be tested by pulling the shoulder straps forward sharply - a n d the belt should
lock).
Consists of two lap straps (but may have other straps also) with metal snap hooks
fitted to one end of each to attach to the seat structure. By regulation must be
suitable locked in.
\*\-&3
QUICK RELEASE ATTACHMENT
RELEASE BUCKLE
- - - . -
At the other end of one i s a quick release mechanism and the other one has a
snap-in fitting. One of the straps is adjustable for length. They are made of nylon
webbing. Figure 34 shows a typical passenger seat belt. Note the quick release
connection a t the seat end of the belt - which should be inspected for correct
engagement and locking.
Servicing
The release mechanism and the adjusting mechanism should not slip under load,
and the release mechanism should release the harness with the minimum of effort
against a moderate load. These tests can be made by sitting in the seat with the
release mechanism locked in the normal way and loading the straps by straining
against them. (The release buckle on passenger lap belts should not release before
the 90" position is reached).
Note. When the release mechanism consists of a spring down flap and cam
mechanism (passenger belts), there may be a tendency for some slip to occur if
the flap is only lightly closed. The belt should not slip significantly before it is
gripped firmly.
The cables and straps of forward release mechanisms should be inspected for
kinks, entanglement, and fraying. Control lock mechanisms, pulleys, Bowden
cables, inertia reel assemblies etc, should be examined for security, wear, freedom
of movement, corrosion, functioning and be correctly lubricated.
Check that the webbing is intact and that no stitching has come lose. Lose
stitching may be re-stitched at user unit level. It is important to check the entire
length of the webbing that runs over the back roller on the seat, on inertia reel
type belts.
When not in use the harness should be properly stowed. he best way to do this
is to fasten the belts in the normal way, take u p all the adjustment and lay them
on the seat.
Rep air
Cleaning
The material should not be cleaned using solvents. If it is necessary to clean the
material a n acid free soap and warm water solution should be used. After washing
rinse well with clean water and dry with warm air.
Colour Change
If the material is to by dyed (to match the cabin decor) permission must be
obtained from the belt manufacturer.
Proof Testing
After repair, and whenever specified in the maintenance schedule, that part of the
belt using material in a load bearing capacity should be proof tested to a specific
load. The load and the method of testing is specified by the manufacturer, but in
general the test load should be '/z of the certified strength of the member under
test. The release should work a t 1.5g.
Storage
Safety belts and harnesses should be stored in clean, dry conditions a t normal
room temperature and away from direct sunlight. Harnesses, other than new
articles in their original packages, which have not been tested in the last 12
months, should be tested before installation. The storage period for new original
packaged equipment before they require testing is specified by the manufacturer.
Records
A record should be kept in the bay of all work carried out on the harness.
~ a r n e s s k should
s be serial numbered to identify them against their record card.
It is a legal requirement that IFE (and other equipment such as lap-top electrical
supplies, in-flight telephones etc) should be so designed that no adverse affects
are felt by the aircraft or aircraft systems - due to such things as electrical supply
system overloading, electromagnetic interference etc.
SAQ 2
What do you feel constitutes IFE and what are your responsibilities towards it as
a B 1 EASA66 licence holder?
The systems fitted to aircraft can vary considerable depending on the operator,
whether the aircraft is short haul or long haul, whether it is a budget carrier and
what class of seat is being considered - and the manufacturer of the IFE
equipment.
rnoodull l A-884
They can broadly be divided into:
* Analogue systems.
* Split analogue digital systems.
2
Digital systems - real time.
x
Digital systems - on demand.
Analogue Systems
This is usually some form of background music. It will come from a tape deck or
cd player and the analogue signal sent direct to speakers in the ceiling/walls of
the aircraft. The pilot/crew can interrupt the normal service to talk to the
passengers on the same system - again all analogue.
,
Analogue - Digital Systems
Some aircraft are fitted with fixed conventional television sets spaced at regular
intervals down the centre of the aircraft in the ceiling (some may be retractable
manually). Some aircraft have retractable flat screens above the passenger's
heads that extend automatically when the system is powered - spaced a t every 2"d
or 3 r d seat row. The television screens receive an analogue vision signal from a
- -
Because some passengers do not what to watchllisten to the film the sound is
sent to each individual seat so the person can select sound if1require.
SPEAKERS
SEAT
MULTl CHANNEL
AUDIO TAPE
4
1 . 1 CHANNEL
SELECT
DIGITAL TO
ANALOGUE TO ANALOGUE
DIGITAL
CONVERTER
I
tff! CONVERTER
This may use a single projector (three gun primary colour projector) to put the
image on a single screen for each cabin. The sound is transmitted to the seats in a
similar way to that described above.
On some aircraft each seat is fitted with a flat screen. This is housed within the
seat arm rest or in the back of the seat in front. The channel and volume contro'
selectors &e housed within the seat --or
-- on an attached hand-set.
I 1
I
A s many as 15 vision channels ark provided by a video reprodu~ingunit. These
are multiplexed and sent down a common line that runs within1 the seat tracks
fore and aft. The channels are de-multiplhkd by the seat electtonics unit, and
one channel (as selected on the s e a t ~ o n t r ounit)
- l is shown on the flat screen.
/
I ,
The sound signal is multiplexed in a similar way. All sound ahd vision is in real
I
time, it cannot bgplayed back or @uton hold!
,
- --
These are vision and sound channels sent to the seat as digital signals from a
bank of cd players. There is a cd player for each film channel and for each sound
channel. Each cd player has a number of laser beams for signal pick-off - one
beam for each seat.
This means that the passenger can select any of the channels (any one of the cd
players) and have control of his/her own laser beam. This means that a film can
be viewed a t anytime. It can be stopped at any time (eg for lunch) and restarted at
the same place later. During this process the particular cd continues to play, it is
just the laser beam that is controlled.
Here I will explain the basic principles of a digital multiplexed system - starting
with the signal inputs to the sound/vision output. Remember the whole idea of
multiplexing is to send many signals down one transmission line with a
consequential weight saving on a multi-line system.
Using figure 36 with a limited number of channels (4 audio signals and 1 vision)
signal a s a n example.
The audio tape deck produces four separate entertainment channels. These four
signals are converted from their present analogue form to a digital form by an
Analogue to Digitdl Converter (AID Converter) - not needed if the original signal is
digital.
These four signals now take turns to be transmitted down the one line and this
process is carried out by a multiplexor. This is similar to many trains travelling
downone main line, one behind the other, but leaving the station from different
platforms'. I n this case, however, it is carried out a t very high speed with
electronic devices and no moving parts.
analogue vis~on
signal to projector
VlDlO
AID CONVERTER
AID CONVERTER
digital
7
d~gitalsound signal
- - -
analwue- ,
to seal units
- 4
- -
- MULTIPLEXOR
SUB-MULTIPLEXOR
AUDIO TAPE
The video for the film produces two analogue signals - one vision and one sound.
The vision signal is sent direct to the television set or the three gun colour
projector (both fitted in the cabin ceiling). The sound signal is put through an
A / D converter and then a sub-multiplexor to wait its turn for transmission (a
nanosecond or two).
These sound signals are now sent to all seats (normally from front to rear) to the
seat electronics units housed under the seats (figure 37).
Within the seat unit the signal is first de-multiplexed. This is the reverse of
multiplexing and puts each separate signal into its own separate "platform a t the
station".
The signal is then converted to an analogue signal by a digital to analogue
converter (D/A converter) ready to be understood by the human ear. Which signal
is actually processed depends on the selection of the seat selector unit - made by
the passenger.
(a) In the arm rest where air phones (small rubber tubes) channel the
noise to the ears.
OR
(b) To speakers in a head set connected to the system via a jack in
the arm rest.
analogue wund
to seat selector
O/A CONVERTER P
l(-)LTIP
1 2 3 4 , film sound
- -
I I I
Note. Video recorders, tape reproducers, cd units etc are housed in the passenger
cabin in a locker (in some cases an overhead locker). Also in the locker will be a
selection of videos, cds etc. There is often a monitor so the attendant can check
that all players are working correctly. The attendant will pick a cd or video with
the appropriate film on depending on the menu - which is distributed to the
passengers.
A Typical System
You need not remember the details of this system but you should understand the
principles and be able to test a typical system.
rnoodull l A-888
One audio channel is reserved for passenger address by the flight crew. When
transmitted, the passenger address audio overrides the program selected at the
passenger seat, so that passenger address is heard a t all seats regardless of the
channel selected by the passenger. This signal is also received by the cabin
speakers (including those in the galleys and toilets).
I
I
-r
1111
P A I I ~ W I I
AWIO-CILANNfL
US1 I U M l I I t l I X f I
ZONE A ZONf C
SlBMUlII- SMMIII- C IlBhUJlll-
PLIXfI ILEXI" rLIXfl
r-------
II T I,C. A N D 0
L -----------
IYPICAL Z O N E
- -
--------,----
-
--
The system consists of three major assemblies: Main Multiplexor; Zone Sub-
multiplexor, and, depending on the seating arrangement, a 2, 3 or 4 seat
Electronics Unit for each seat group.
In turn, the Main Multiplexor is connected with the zone sub-multiplexors via a
single coaxial cable. Up to four additional zone-generated movie audio channels
and a passenger address audio channel are connected to each zone sub-
multiplexor.
Each zone sub-multiplexor is interconnected to all associated seat electronics
assemblies within the zone via a single coaxial cable.
The amplitude of each sample is then measured and compared with a scale of
discrete values. A digital word is generated (eg 0 110011000) which represents t h e
amplitude of each pulse, and a digital pulse train is produced. This process is
called PCM.
Seat Electronics
---- Unit
I -
-- --
The Seat Electronics Unit (SEU) is involved in the operation of both the Passenger
' I
~ n t e r t a i b m e n System
t and the Passenger Service System. These systems are
independent of each other.
The basic objective of the SEU is to deEiultip1ex the digital signal a n d convert it
into its original analogue audio form. , I1
\
I
I ! I
1 1 I
1 I
MOSFET Module I ~
I
- -
This module is the heart of the SEU, wher-e data is demultiplexed a n d stereo
entertainment, passenger address override, and channel selection functions are
controlled.
The analogue output from the D / A converter is directed to the output audio
processor modules according to the channel selection a t each passenger seat.
When a passenger selects a channel it is remembered by the MOSFET. Each time
that channel appears in the multiplexed scheme, it is switched to the audio
output lines for that seat.
These are two distinct modules that operate a s a unit to accomplish the self test
function. They are used to check transducer continuity and audio power output
circuitry common to passenger seat groups. A successful self-test will light the
appropriate attendant call lamp.
Fig. 39 TYPICAL SEAT ARRANGEMENT FOR
A MULTIPLEXED SYSTEM
-- -
,
The components continuously monitor the state of each passenger's seat control
unit switches. This task is accomplished by a Seat-to-Seat a n d a Seat-Group-to-
Seat-Group sampling of each zone. The sampling is under control of a
TimerIDecoder (T/D), t h a t provides timing, synchronisation, and acts as an
interface between each seat group and its associated passenger service unit.
Each seat group has a Seat Electronics Unit containing, in addition to the
entertainment de-multiplexor, and a seat coder for the PSS. The seat coder
accepts passenger control function inputs from each seat in the seat group and
timing a n d data from t h e T / D . The seat coder encodes the passenger control
function, a n d during a specified time period, the encoded command is transmitted
to the T/D.
rnoodull IA-891
Upon being received a t the T/D, the circuits immediately transmits the received
data to the PSU Decoder. The PSU Decoder, which h a s been synchronised with
the transmitting Seat Electronics coder by T/D timing, accepts the data, and
decodes it, a n d depending upon the original command, will control the state of a
reading lamp or the attendant call lamp (ie switch it on or off). Two
TimerlDecoders are utilised to service each passenger cabin zone. The T/D1sin a
zone interface with the attendant's station for that zone.
SAQ 3
You are called to a n aircraft that is about to depart by the Cabin Services Director
(the person in charge of all the cabin services on a large aircraft - different
operators may use different titles), who reports that the PA system i s not
functioning - list your actions.
CABIN LAYOUT
SAQ 4
,
Operators have some latitude in!the design of the cabin interior a n d will often
have their own cabin interior manuals which need to be cons'ulted in specific
cases. Here we will cover, mostly,-the-regulitions that apply to cabin interiors.
In general the cabin staff need to man the emergency exits during a n evacuation
procedure, therefore, you would expect to find the attendants seat located by the
door in the zones they are responsible for. Seats, galleys and toilets will need to he
positioned for ease of access both in normal situations and in emergencies.
Galleys are located in clusters around the cabin in such a way as to be able to
cater for the whole of the aircraft. There are no legal restrictions on galley
location, b u t by default they are usually placed a t the front a n d / o r the back of t h e
cabin for medium sized aircraft. On larger aircraft they are placed a t mid positions
in the fuselage.
Toilets tend to be spaced at the ends of cabin areas on medium sized aircraft with
additional "toilet blocks'' being positioned a mid points along the cabins. Each
class zone will have a t least one toilet. Also, a t various locations around the cabin
there will be various closets, some for emergency equipment, some containing IFE
equipment a n d some for coat, hat and luggage storage etc.
Minimum Seat Pitch
CAP747 (was previously in ANs) shows the minimum distance between the seat
cushion and any other seat back or fixed structure is 26" (66cm).This is shown
on figure 40 as dimension A. Dimension B must be a minimum of 7" (18cm),this
is the distance the passengers leg has to move from thigh support to seat back.
The vertical separation between seats must not reduce less than 3" (7.5cm).This
includes the seat in the reclined position.
Around some emergency exits (typically overwing small and slightly larger exits)
the clearance has to be increased. The vertical separation between seats a t these
locations must not reduce below 10" (25.5cm).In addition the seat backs at these
locations must not %re& forward' as other seat backs do.
D~menslanA
datum polnl
haghl abow
lz:7wb
-
Range lor
dlrnension A
datum mlnl
The reason for the break forward action of the seat back is to prevent head injury
of passengers a s they impact their head on the seat in front under heavy brakmg
etc. The seat back breaks forward to move out of the way.
- 51 -
rnoodull l A-893
Note. These dimensions are not the seat pitch as the seat pitch is usually
measured from the feet of the seat and so different dimensions might be found.
CS25 specifies aisle width which will depend on seat numbers. Maximum
numbers of seats abreast in a single aisle aircraft is 3.
The minimum number a n d size is specified in CS25 and are related to the seating
capacity of the aircraft:
I
I I N
For techbical details of doors and exits pleise see the books in this series entitled
Structures. , I I
-
- - - - . .
Flame Proofing
All materials must be flame proof to the standards laid down in CS25.
CAP747 GR 13. (Was AN58). States that furnishing materials (seats, berths etc)
should be flame resistant to CS25 standards. The material must be flame
resistant after 3 representative cleaning processes - using three samples with the
flame on the material going out after a specified time.
CAP747 GR 14. (Was AN61). Applies to public transport aircraft over 5700kg with
20 or more passengers. Deals with wall and ceiling panels. This states they must
meet flammability and smoke emission tests as laid down in BCARs or EASA25.
Note. CAP = Civil Air Publication published by the CAA and GR = Generic (general)
Requirement.
Flame Proofing Testing
CS25 states that 3 specimens have to be tested and details of flame areas,
propagation rates, longevity rates and specimen orientations are comprehensively
covered. CS23 specifications are simpler and states that for compartment panels
the flame length should be no longer than 15cm and maximum duration should
be 15 seconds. The figures for upholstery are 20cm and 15 seconds.
The partitions separate the various compartments, and also serve a s mountings
for various items of equipment. They may be transferable to alternative positions
in the aircraft to provide for variations of the seating arrangements.
CEILING PANELS
REF 25-23-41
I I
CLOSlNG COVERS DADO PANELS
R E F 25-23-41 R E F 25-23-44
The partitions are located and secured in position by foot mounting brackets
which pick u p on the seat rails, or shoe-mountings, and attachments which pick
up with the aircraft side-wall or roof structure.
Disconnecting the foot, ceiling and wall attachments enables the partitions to be
moved to their alternative position.
Ceilings
These a r e fitted to a framework suspended from the top of the fuselage structure,
or on some aircraft, fitted to the top of the fuselage structure direct. The ceiling
may contain:
k Projection equipment.
* Passenger Service Units (PSUs).
* Luggage lockers.
A
Television sets (CRTs/ flat screens).
-k Lighting.
* Insulation.
PANEL CONNECTIOH
SECTION
B- 8
EXAMPLE OF UIHOOU PANEL COHHECTION
All Metal Construction. These normally comprise aluminium alloy sheet parts,
formed and riveted to a framework of light-alloy angle members, channel sections,
brackets and cleats.
Window Reveals
Fitted to the sides of the cabin a t each window location and may be fitted with:
The reveal can be clipped into position and so removal is straight forward. It will
need to be removed for maintenance on the transparent panel, lamp fixture shade
etc.
INNER
REVEAL
Fig. 43 ' ~ P I C A ~L N D O W
I I I
-- /
\ /
I I
..
I
Cabin saggage Stowage --
I II
i
Cabin baggage may be stowed uhder the seats and in cabin blaggage lockers.
These are usually overhead lockers (on large aircraft) but ma$ de beside the seats
or in front of them where seats are at the front of a cabin.
- -- -
Overhead Lockers
These must conform to strength, fire and smoke requirements a s laid down in C"
25. They are normally of composite or plastic construction.
These are usually situated in the ceiling above each row of seats.
After disconnecting the service connections the unit complete can be lifted off its
hinges and removed.
Fresh air supply (Gasper Air). Cold air supply to the passenger
louvres. On some aircraft these may not be fitted.
Oxygen supply line. Supplies gaseous oxygen to the passenger masks
from an airframe mounted system in an emergency. This system is
not fitted if a chemical oxygen generator is fitted.
Electrical power supply - for passenger reading lights etc.
Chemical oxygen generator. Fitted on some aircraft to supply oxyge*
to the passenger masks -- i n an emergency. (See b o k - o n Cabin
Conditioning and qre,ssurisation). pI
Oxygen masks. ~ h e s e f a l out
l automatically if cabin altitucle rises
above a certain value (say 10,000ft).
Reading lights. On some aircraft may be operate+ directly by a switch
on or near the passenger seatcon many aircraft 'the passenger
- --
Attendant call light. Lights when the attendant call button is pressed
on the seat arm. Also lights a lamp at the attendant's position. It may
also be connected to the inflight entertainment system so that on
TEST MODE it will light if the seat is receiving the audio signal. When
IFE TEST is pressed all attendant lamps should light.
Speakers.
Information signs (toilet engaged, fasten seat belts etc)
CARGO
Passenger Luggage
Apart from cabin baggage, luggage is handed over with the tickets at the check-in
desk. After weighing and taggng (and security checking) it is placed on a conveyor
belt from where it is loaded into containers or loaded individually into the aircraft
using conveyer belts.
Loaded containers are towed or driven on trucks to the aircraft in the ramp area
where they are raised to aircraft sill height for loading.
Cargo Consignments
Loading - Freight
Pallets can be loaded from ground level by fork-lift trucks or 'scissor' trucks. The
loading doors may be on the side of the aircraft or the front or rear. Once the
pallets are inside the aircraft the loader/operator can manoeuvre them into
position either manually using rollers or mechanically using motorised wheels in
the floor. These motorised wheels retract into the floor until required for use.
- 59 -
moodull l A-901
The B747F for example, h a s a mechanised cargo handling system on the main
deck. Pallets or containers are moved in the aircraft on a motor driven system by
two men, who can load the whole aircraft in about 30 minutes.
Loading - Baggage
The system will vary with the aircraft, eg on the B747 the system is similar to t h e
above a n d the pallets a r e loaded from special trucks equipped with elevating
platforms with motorised wheels in the floor.
On the B757, for example, each cargo hold is fitted with a number of telescoping
f l a t - b e d o d u l e s . To load the aircraft they are moved by an electrically operated
--
rotary, actuator forward to the door.J'heyXare all telescoped into each other
opposite the cargo door. I , 1
,
BULK CARW M Y
-
DOOR
v
On large aircraft loose baggage is secured using traditional netting and the netting
secured using the tie down fittings.
On small aircraft the cargolbaggage is loaded by hand into the hold and secured.
Notes:
1. For aircraft of 19 seats or less cargo and baggage must be weighed and
placed in the aircraft in such a way a s not to upset the C of G. This may be
done by working out the moment arms, or on small aircraft, placing the
baggage on the C of G. Aircraft must not exceed their MTWA. With most
operators a standard form simplifies the procedure.
2. For aircraft with 20 or more seats the weight and C of G location may be
calculated using the pro-rata standard masses stated in EASA OPS. When
packing luggage items into standard containers - when full the total weight
of the container can be ascertained.
Powered cargo handling systems is a luxury not all aircraft have. Most aircraft of
moderate size have some form of astsistmce for the loading and unloading of cargo
(a powered conveyer belt for example). Describe below is a typical powered system.
Check your aircraft and see what system it has.
A cargo bay will be split into a number of areas such a s a Containerised Cargo
area and a Bulk (or loose) Cargo area.
With containerised cargo all the goods are loaded either onto pallets or more often
into specially shaped containers. If these containers are not standard containers
then they will have to get CAA approval separate from that of the aircraft.
Bulk cargo is usually located a t the back of the aircraft and will have oversize and
lose articles restrained by nets.
- 61 -
rnoodull l A-903
Fig. 48 STANDARD LD CONTAINERS IN T H E B 7 4 7
* Guide rollers
* Sill rollers
* Roll out stops
* Lateral and longitudinal power drive units
* Ball transfer mats
* Lateral guides
* Roller trays
* Centre guides
* Pallet locks
* Control panel
Power is provided for t h e cargo handling system when the cargo door is fully open
and the system is switched on a t the control panel. The supply is usually via the
ground handling b u s , which is live as soon as ground power i s plugged in. This is
useful for cargo handlers who don't need to provide full aircraft power to load the
bays.
LATCHES,
w
LATERAL GUIDE - SMALL
POWERED D R I V E UNIT
With t h e container now on the ball transfer panel the operator will move a joystick
on the control panel (fitted to the side of the fuselage just inside the door) to
power first the lateral Power Drive Units (PDUs)to bring the container into the
aircraft. Then, still using the joystick, the longitudinal PDUs will be powered to
take the container down the cargo bay, along the roller trays.
When the container is in the correct location (normally a t the furthest end to one
side of the hold) power will be removed and the pallet locks installed to prevent it
moving.
The lateral guides prevent the container from skewing down the bay as they enter
the aircraft. They are normally u p and hence straighten the container. A s the
longitudinal PDUs are selected the lateral guides momentarily drop to allow the
container to pass over the top.
The roll-out stops prevent the cargo from rolling out of the bay. As the container
enters the aircraft the roll-out stop is automatically (by t h e weight of the
container) pushed down. As soon as the container has passed the rollout stops
spring back u p a n d prevent the container from leaving' the aircraft. The mechanic
can select them down when unloading.
Various rollers are placed in the system to keep the cargo straight a n d stop it
from impacting the door, the aircraft or its equipment.
The PDUs c a n have their power removed individually to prevent them from
turning when cargo is already installed in them. The furthest bay from t h e door
have containers in them whilst the rest are still being loaded for example. I n
addition all t h e PDU's have a manual disconnect facility to allow for manual cargo
loading operations.
i
Figure 51 shows the power supply and logic circuits for the system. Take a little
time a n d study the AND gates and how they work; note the power supplies a n d
the location of the PDUs.
Maintenance of the cargo handling system is fairly straight forward and trouble
shooting guides are given in the maintenance manual. Most prdblems with this
system are usually through misuse. The PDU tyres need checking for wear a n d
condition. The door sill a n d seal depressor will often become damaged - as will
parts of the cargo hold liner. If any powered item fails to work then the problem is
tackled the same way as any electrical problem - visual first followed by a logical
approach to rectifying the fault.
Bulk Cargo
Bulk cargo is handled in the old fashioned way by using manual labour. Loose
and oversize iterns are put in this area as well a s any livestock. If livestock h a s
been loaded a n entry in the Tech Log is required to inform the crew to keep the
bay heated. All the items are restrained using nets and ties (see figure 5 1).
Dangerous Goods
Almost all operators now have specialist cargo loaders that deal with the packing
and loading of cargo, but as a licensed engineer you still need to be aware of all
cargo loading including any 'dangerous goods'.
The Air Navigation Order and Regulations (the ANO) gives details of goods that are
not permitted on-board aircraft.
I I
The list is extensive and includes anything that might harm the aircraft, its
occupants, or those beneath the-flight-path, or those a t or near-the take-off and
landing airfields. Examples include:
* Munitions of war
* Weapons
* Flammable liquids
* Mercury
* Chemicals
* Radio active materials
* Bacteriological agents
There may be times when dangerous goods have to be transported and where this
is the case the consignment needs to be packed in the specified manner a n d the
shipping information must be presented to the aircraft commander at the same
time a s his load sheet. (Usually airlines do actually combine the dangerous goods
form and the load sheet and the captain must sign this before departure).
rnoodull lA-908
UPPER ATTACHMENT F I T T I N G
Cargo Holds .
For the classification of cargo holds please refer to the book in this series entitled
"Structures - I".
AIR STAIRS
These are generally considered to be stairs for passenger use that are carried on
the aircraft. They may be built into the design of the door so when the door folds
down the steps can be used. With this type the hand-railslhand-ropes deploy
automatically. The door may be fitted conventionally to the side of the aircraft or
beneath the fuselage at the rear. The door is designed not to touch the ground.
Another type of air-stair is pulled out from the side of the fuselage complete with
handrails and these are fitted to the sides of the door aperture before the
passengers use the stairs. These air-stairs may be stowed in a separate
compartment under the cabin floor with its own separate fuselage closure panel
or may be pulled out from under the cabin floor through the door aperture once
the door is opened.
rnoodull l A-909
HAND RAILS
UNFOLDED 8
21 n) I I\
ATTACHED TO
FUSELAGE
\ n\
/
HAND RAILS
UNFOLD
WHEN DOOR
IS OPENED
- - Fig. 54 AIRSTAIRS -
L \
-- \
' I '1
That concludes this section a n d i t h e book. Take some time now ko recap a n d
consolidate your knowledge with the following exercises. The adswers can be
1
found lin the text. - -
, --
/
II - -
\
~xercises , I I I
' I
1. &here is information fourid on minimum seat pitch?
2. What t@es of cargo holds are there?
3. -Explain the operation of a containeri6ed rnotorised cargo bay system.
4. What is the purpose of the roll-out stop?
5. What are dangerous goods?
6. Can the aircraft carry them and how?
SAQ 1. The following checks should be carried out. Inspect attachment lugs,
fittings, push/pull rods and door/slide operating mechanisms for security,
damage, corrosion and wear. The slide pack itself should be checked for signs of
chafing, damage and security of attachment. The transportation pin should be
checked that it is removed. Check that the girt is securely attached to the girt bar.
Check all lacings a n d Velcro strips for correct fitting. Close door and check the
'
girt bar for correct operation and that it latches correctly to the floor fittings.
Check also for security and damage.
Check the bottle pressure and date life. With the decor panel fitted check that
bottle pressure indicator is visible through inspection window and all handles
operate freely. Check the door opens and closes correctly with correct clearances
and that arm/disarrn indicators show. Check that all electrical indicators work.
SAQ 2. IFE i s basically all the electrical equipment that goes to the seat, including
video and audio signals, electrical power, audio and vision signal equipment and
data handling equipment. In other words all the system from the box that
reproduces the sound and/or vision to the speaker at the other end. Provided you
are B 1 qualified with appropriate certification authorisation from a EASA145
company then it is your responsibility to look after these systems and clear the
CRS. (AN 3 refers). Responsibility covers avionic LRUs and electrical power
supply systems where simple BIT tests or using simple test equipment can verify
the s e ~ c e a b l eof the system. Of course the seat it-self is 'all yours7anyway.
j ,"
SAQ 3. Gain information from the crew as to the details of the defect. Confirm the
defectandsee if it can be isolated to one zone. Check the AMM fault finding
section. Carry out a system BITE check - using the equipment BITE or any
aircraft centralised fault location equipment. Check the boarding music is heard
from all speakers (if it uses the same speakers).
If all speakers work then it is a fault in the dedicated part of the PA system.
Check that power is available to the system, if it is not find the fault and rectify.
Check the wiring, replace if open circuit. Check the individual microphone
handsets - change any that do not work. Check the PA switching units and any
other electronic units - change if necessary. Check the system multiplexors (if
fitted), change if defective. If the boarding music is not heard from all the speakers
then c-heck the main multiplexor (if fitted), change if defective.
If only some speakers do not work then it is almost certainly an open circuit in
the line downstream of the last 'good7speaker - locate and rectlfy. If the fault
cannot be cleared in a reasonable time scale check the MEL (Minimum Equipment
List) to see if the aircraft can fly (it probably cannot). Ifit can the crew must be
made aware of the problem and it must be recorded. If it cannot be fmed and the
MEL does not allow flight then the passengers will have to disembark.
During all this the pilot will be wanting to use his/her take-off slot and might
request that there is no time to complete all the checks with the passengers on-
board - there might not be access because of passengers anyway and they might
be getting restless as well.
SAQ 4. First and foremost it is to allow the quick and successful evacuation of a n
aircraft in a n emergency. Secondly it is for the comfort and convenience of the
passengers. Standard layouts within a fleet also allow the cabin staff to move from
aircraft to aircraft without the need for re-training.
LBP Dec 03 - Feb 04 - April04
NOTE: It is possible that some of the above statements may not be too
meaningful when read out of context, so it is suggested that the appropriate
book/subject be read first then the information above be checked against that
topic.
moodull Ip i 1 2
CONTENTS
Page
Smoke detectors . \
\
Fire extinguishing systems can be divided into fzed, portable, and mixed
systems.
J A R 25 specifies the minimum capacity of each fixed system and that the
contents must not be hazardous to personnel or the structure.
-
?- -
-,
I !
A mixed system is used in some &craft baggage and service compartments.
The distribution pipelines are fixed in theiappropriate comp'atment and
coupled to adapter points within the crew drea to which a p,oqtable extinguisher
is plugged into when required. Not very'cpmmon. -
, 1
-- - -
\
I ; !
Extinguishants On Fixed s y s t e k s
I / 1 ~
ethyl Bromide IMB1. Boils at about S C a i d is used for the protection of
-
Not very common, though might be fitted to engines of older aircraft where the
engines are away from the fuselage.
It has little or no corrosive effect, although halogen acids will form if its
products, which have been decomposed by fire, come into contact with water.
In contact with fire BCF volatilises instantly, giving rapid flame extinction.
APU EXTINGUISHER
FACILITIES
CARGO I I rp
COMPARTMENT I
- - -..-..,--,JAL
I
1 '
Fire Zones
Fire zones are designated in an aircraft where there is a potential fire risk.
Each fire zone will have a fire and/or smoke detector system and a fire
extinguisher system. Certain fire zones will have fire proof bulkheads (engines
and APUs), and fireproof linings (cargo bays). Most engines will have more than
one fire zone (as specified by JAR 25).
The following are usually designated fire zones and/or fire potential hazards.
* Engines.
* APUs.
* Fuel tanks.
* Cargo bays.
* Wheel bays.
* Toilets (paper towel disposal bins)
Each designated fire zone will have a fire/overheat detection system and an
extinguishing system. Fire detection systems may be used for overheat warning
along hot air ducts etc.
Passenger compartment linings and furniture materials, a n d cargo
compartment interior linings must meet the fire resistant specifications a s laid
down in JAR 25 and ANs 58, 61 and 83. Cargo compartments a r e classified
primarily on their location in relation to how a fire can be tackled:
* Class A Easily accessible in flight where a fire would be quickly
detected by a crew member a t his/her station.
* Class B Must have a smoke/fire detection system and access
can be made to any part of the compartment by a
person with a hand held fire extinguisher.
-k
Class C Must have a smoke/fire detection system a n d a built-
in fire extinguisher system controllable from the flight
deck.
t
Class D Any fire occurring within the compartment will be
completely contained and compartment volume is
1000 cubic ft or less.
~r
Class E For cargo aircraft only. It must have a smoke/fire
detection system and means to shut-off all ventilation
I -
airflow-to/from the compartmentT- -
-
- --
,
WINDSCREEN DEFOG
With reference to figures 3 a n d 4. Each fire bottle has 2 discharge heads and
the fire switches in the flight deck are supplied with 28V d c from the essential
or hot b u s bar. When the extinguisher switch is operated current will flow to
the appropriate fire bottle head detonator unitlcartridge unit/squib and to the
warning lamp / indicator fuse.
The detonator unit will operate allowing extinguishant to go to the fire zone via
the directional flow valve.
dc BUS BAR
In an emergency most aircraft have systems that will operate all the fwe bottles
automatically (except "toilet" and portable bottles).
In the drawing a n inertia switch is fitted that operates if the aircraft is put
through more than say 3g (aswould happen in a crash landing).
On some aircraft a rubber covered crash strip may be fitted beneath the
aircraft. If the fuselage touches the ground the two elements of the strip come
into contact to complete a circuit - operating "all" the extinguishers.
When operated the pressure in the pipelines (on some aircraft) pushes out a
small plastic discharge indicator disc on the outside of the fuselagelengine
nacelle (figure 4). This allows outside verification that the system has been
operated. If the disc is found missing then a check should be made on the
rubber seal inside the unit.
If it is still their then it i s possible that the disc has become detached by the
airflow and needs replacing. If the rubber seal is missing then there is a good
chance t h a t the system h a s been operated - of course there should be other
indications also - Tech Log entry - signs of a fire - flight deck fire handle
position - fault computer etc.
Note. All fixed fire systems are connected to the essential or hot dc b u s bar.
PIN
Concorde, for example, is fitted with a "two shot" (one fire bottle per engine)
(figure 8) system whilst aircraft like the Boeing 747 (figure 6) are fitted with a
two shot system with t w o bottles per engine. Study both these figures and note
the general layout and operation.
These are a type of non-return valve which only allows extinguishant to the fire
zone irrespective of which bottle h a s been fired. An arrow on the valve body
allows for correct alignment when fitting.
8. SWIVEL NUT
9. PRESSURE SWITCH
blank
rnoodul11~~990
BOTTLE I BOTTLE 2
/
BOTTLE I BOTTLE 2
- --
--
LHK 1 KIUUC
CARTRIDGE
TO ENGINE -
-
/ -
-- - --
MAINTENANCE
Extinguishers
Check that the bottle is of the correct type a s laid down in the AMM and/or the
IPC, that all markings on the container are legible and that the bottle is
securely attached. Check the bottle is within life (bottle date stamped). Check
for signs of leakage, corrosion, dents, scores, and damage. The state of charge
should be checked by reference to the flight deck indicator (if fitted) and/or the
gauge on the bottle (if fitted) and by carrying out a weight check.
The fully charged weight of the bottle is stamped on the bottle neck or on the
bottle itself. On some aircraft this weight includes the blanking caps but
excludes the cartridge units, on other aircraft (Boeing for example) the weight
includes the cartridge units (check the AMM). Typical weight tolerances are
Boeing 4%, and BAe 0.1 lbs.
EXTINGUISHER FIRING BUTTONS
DIRECTIONAL FLOW
AUTOhWTIC EXTINGUISHERS
EXTINCTEURS,AUTOMATIQUES
i 1
1 ,
- - /
I
Check the discharge indicator. ~ F o ~ e x a m p lwith
e , the pin type~thzitthe pin is
flush with the cap. Check the threads f&,security, damagei ana 16&ing. On
assembly where specified u s e the approved grease, eg barium 1 chromate grease.
1 ,
1
l ' I
I
-
~ e t o f i a t o units/
r Squabs -- --
These are dangerous s o handle with care. Never put then i n your pocket.
Always point the discharge end away from you and other people. Never torch
the electrical connector ends - you could set it off.
Check detonators for continuity and insulation. Remember to use safety test
meters for this purpose with the detonator off the aircraft, removed from the
bottle and facing away from any personnel.
Note. Early detonators were wired to the aircraft using a terminal block on the
detonator head and compression fittings. Double check - particularly on the
"two shot one bottle per fire zone" system that detonators are correctly wired.
The wires should have identification codes which must be correlated to the
aircraft wiring diagram. If they have no codes or they have been obliterated
then an electrical system function check must be carried out - with the
detonator wires disconnected.
The reason for this check is to make sure that the correct pair of wires are
fitted to the correct detonator - so that when the pilot selects "shot one" he gets
"shot one" and not "shot two" - which would mean the extinguishant going to
the wrong fire zone.
On most modem fire systems the detonators are connected by a plug and
socket and the pins are so arranged that incorrect connection cannot be made.
QUESTION How would you check that the correct cartridge unit is being fired
when the appropriate switch is selected in the flight deck? (5 mins)
- - --
Cables
Pipelines
Before installation the pipes should be blown through with clean dry air or
nitrogen. After installation the pipe system should be pressure tested in
accordance with the AMM. Check pipes, spray rings, threads, and unions for
damage, corrosion, and security of attachment.
Valves
Check for corrosion, damage and security of attachment. Check that the plastic
disc is secure and in position and the sealing plug is in the pipe.
Inertia Switches
Always set/activate after fitting to the aircraft and before putting power on. If
you put power on before pressing the SET button in then all bottles will be
discharged. Refer to the AMM.
STOFWGE
I
Extinguishers
I \
Detonators
The fitting of fire and overheat detectors is laid down in JAR 25 (for large
aircraft). They must be fitted in Designated Fire zones of all power plants above
12,5001b.
There are several fire and overheat detection systems and the following pages
gives a brief description of some of them. The detectors can be divided into two
main groups - unit type and continuous type (fire wire).
DETECTORS
TYFES OF DETECTORS
I
UNIT TYPE DETECTORS 1 -- -
I. - -_
These are used in fire zones singly or more than one to give;better coverage. In
some cases they are used in cohjunction with a continuous' detector.
I
I
,
Melting Link Switch
- - -
- -.
--- - - I
Thermo-Couple Detector
When the fire goes out, the pd drops and the relay/electronic circuit will cancel
the warning.
rnoodull I A - ~ %
12 -
Differential Expansion Switch
This consists of a switch in the fire zone connected between the dc essential
b u s bar and the warning systems in the flight deck. It consists of two contacts
held apart on a spring-bow assembly which is secured a t either end of a n alloy
steel barrel or expansion tube. When the unit experiences heat the barrel
expands length-wise. It's coefficient of linear expansion is greater than that of
the spring-bow assembly, t h u s the spring-bow is caused to straighten and the
contacts to close - causing a flight deck warning to come on.
SPRING BOW
-
/ /
TERMINAL
Fig. 9
ANSWER Of course the barrel will contract (more than the spring-bow), and
cause the contacts to open, thus switching off the warning.
Besides the usually visual inspection for security, corrosion, damage etc, the
unit is tested by the u s e of special heated tongs that are clamped to the
expansion tube. These will cause the unit to expand and give a warning light in
the flightdeck. When the tongs are removed the unit will reset causing the light
to go out.
Light Detectors
These use photo-electric light detectors that converts visible light into an
electric current. Their electronic circuitry analyses the light spectrum and will
only give a warning when it detects light coming from a hydrocarbon fire. Are
self resetable.
For large fire zones a number of unit type detectors would have to be used, so
it is often better to use a single continuous type.
RESPONDER
TITANIUM H~DRIDE
(GIVES OFF HYDROGEN GAS
AVELANCHE FOR LOCAL HEATING)
When the temperature decreases, the pressure drops and the warning circuits
are de-activated. This may be used for overheat and fire detection.
-
-
-r .. - ..
OVERHEAT EXPANDS
lNERT.AVERAGlNG GAS
ALARM SIGNAL
POWER SUPPLY
: RE~PONDERALARM SWITCH
(NORMALLY OYEN)
I
,
- AVERAGE OVERHEAT
I
1 I
FIRE RELEASES ACTIVE GAS
FROM yYDRlDE
-
CORE
.-
ALARM SIGNAL
f
POWER SUPPLY
RESPONDERALARM SWITCH
(NORMALLY OPEN)
LOCAL OVERHEAT
FAULT SIGNAL
POWER SUPPLY
FAULT STATE
The fire wire is pre-pressurised so that a pressure integrity switch will operate
should the firewire develop a leak. This is incorporated in the responder and
linked i n with the element self monitoring circuits.
The fire wire may be a twin fire wire with the two wires running in parallel in
rubber lined clips.
El
1 - ---
L
1
I
?H-J-,r
5
AGENT I
I
R
- -
f '
1
1
TEST
-- - ENG, FIRE
8 i
I
I
-
qUsH
Two control panels are provided - one for each engine. The fire push button (1)
is guarded and released out. When this happens the following occurs for this
engine:
-k Aural warning is cancelled.
* Squib (cartridge) is armed.
A
The following valves close - LP fuel - hydraulic - air bleed -
pack valve.
* Generator deactivated.
After operation of button (1)the Squib button (2) is pressed to cause the fire
bottle to discharge. The squib button lights when button (1) is pressed to
indicate which squib button to push. The DISCH area lights amber when the
bottle is discharged.
The test button (3)tests the system. When pressed:
* Warning chimes sound and master warn lamp flashes.
* ECAM engine fire warning is activated.
* Engine fire button (1)lights red.
* Squib lights illuminate white.
* DISCH lights illuminate amber.
* On engine centre pedestal panel fire light illuminate.
Not used on civil aircraft. A pyrotechnic cord is housed within a small bore
steel tube (similar in size to ordinary fire wire). When a n over-heat situation
arises the cord ignites, creating pressure and operating a pressure switch
within the control module.
Electrical Firewire -
-
I
These form a continuous stainless steel (or'inconel) loop a k u h d the fire zone
with both ends of this small di-eter tube entering a control
, i
I
I
box.
I
I
,
Modem technology exists for the single loop to pass around several'fire zones
with the electronic control box ablFto detect where, in the loop, theloverheat
has occurred. Most aircraft ha?e one loop - usually duplicated - for each fire
I
zone.
, l 1
The element has one or two central electrodes which are inkulated from the
outer tube by a temperature sensitive material. In some aiicraft the outer tube
element is supported on special metal supports and may be protected within
perforated stainless steel tubes. It is more usually supported in rubber covered
"P"clips to prevent chafing.
blank
There are basically three types of electrical fire wire - resistive type, capacitive
type a n d resistive/capacitor type.
(a) Resistance type. With this type the central electrode has a positive
voltage applied to it and the outer case is grounded. As the temperature
rises the insulation breaks down and current will start to flow from the
central electrode to the outside of the fire wire - to earth.
This current will cause a relay to operate in the control box and cause
warnings to come on in the flight deck.
When the fire is out and the temperature drops the insulation will regain
its former properties, the current will cease to flow, the relay will open
and the warnings will be cancelled.
The ac supply provides power for the fire wire, the d c supply for the
relay, and the dc test for the test circuit. When the "press to test"
button is operated (from the flight deck) a current is passed through the
control box and the complete length of the central electrode of the fire
wire to operate the warning lamp in the flight deck.
Should the electrode be broken or the control box not work correctly or
any supply be missing then the warning lamp will not operate. With a
break in the fire wire, fire detection is not affected b u t "press to
test" is.
(b) Capacitance type. Capacitance is the ability to store charge, and the
central electrode and shell of the fire wire form a capacitor with the
insulation or dielectric between. The capacitance of a capacitor depends
on several things and one is the value of the dielectric (dielectric
constant). This changes with temperature. As temperature rises so does
the capacitance of the fire wire.
The core is supplied with half wave ac current which the wire stores
during the first half of the cycle and returns to the control box during the
second half cycle.
!c) Resistive/capacitive type. With this type nf fir^ wire the impeds=ce as
welldas the resistance ismonitored. 'with an increase i n temperature the
resistance drops and the impedance becomes more rqactive. When this
happens the detector unit registers
I
this as a fire. A pvrk resistance will
be registered as a fault. / I
1
I - ,
--
I
With rhost aircraft the signals from-the above systems go t o a card within a
rack mounted unit. This will prockss the signal and send w v i n g s signals etc
1 I
to all other appropriate systems/ units.
1 I
I
--
-- - - - - - - -
FIREWIRE ELEMENTS
ELEMENTS FIREWIRE
CONNECTING CABLE
CABLE DE CONNEXION
rnoodutl lkBg
Liquid Type Detector
A small bore stainless steel pipe is filled with liquid that expands on heating -
the pressure causing a pressure operated switch to close an electrical contact.
When the heat is removed the liquid contracts and the switch re-sets. Rare.
SMOKE DETECTORS
On some aircraft the smoke detector system might incorporate an air duct
system with fans that draw air from various parts of the aircraft through a
single-detector unit. With this system-there may be provision to "select" the
area that-& is being drawn from andhence the ability to determine the action
to be taken in the event of a s4oke warning. l 1
I
I
Most detectors have their own electrically driven fan to draw in the air 'and this
may come via a small plenum chamber. .,
- ,
OUT
LIGHT BEAM
TEST
LAMP TRAP
BLOWERS
I /
moodull 1.A-933
- 20 -
Photoelectric Smoke Detectors
Light Scatter Type. (Figure 17) These work on the principle that when light falls
onto a photo-electric cell it will produce an electric current.
A bearn of light is caused to shine within a light proof container. The beam is a
focused beam which shines into a light trap (painted mat black to absorb the
light).
When clear air is being drawn through the unit no light is scattered and no
light reaches the photoelectric cell. When smoke enters the unit it causes the
light rays to reflect off the smoke particles and scatter in all directions.
The scattered light rays fall onto the photoelectric cell producing electricity (in
basic terms, one photon of light will produce one electron of current). The
output is amplified, put through a relay, which causes a warning to come on in
\ ~ 1 -
- n : - i _ L_1--1-
I I I ~ I I LUCCK
~lle
- -
- a- -u- -l- Ia - - -1 --:
----
iulu v l s u a .
1
I
-
- - -
When t h e smoke ceases the reverse happens and the warninis cease.
1 ,
In some units two cells are used with on&being subject to smoke (if it is
present)and the other not. Both have the same light sourcd a p d ark connected
by a Wheatstone bridge circuit. ~ k e n 3 m o k eis present one,cell produces a
current which unbalances, an btherwise balanced bridge. Thq bridge output
will operate a relay to cause a &-ing to come on in the flikht deck.
I
Of course, when there is no smoke-present everything reveqses and the flight
deck warning goes out.
QUESTION All of these units are fitted with a "press to test" facility. In figure
17, the "press to test" button sends a 28V dc supply to the test
lamp. When it's light falls on the photo-electric cell a warning is
given. However, the pilot lamp may not be working so the test
would be invalid. How could the test be made to be valid?
(5 mins).
ANSWER If the test lamp is wired in series with the pilot lamp, the test lamp
will not work unless the pilot light is also working.
IMPORTANT. If the pilot lamp fails it is important that it is replaced with the
correct lamp. The wrong larnp may cause the sensitivity of the unit to drop,
reducing it's effectiveness.
Light Absorption Tvpe. With this type of unit a photoelectric cell is placed at a
distance from a light source (within the unit) so that the cell receives 100% of
t h e light during "no smoke" conditions. When smoke is present the amount of
light reaching the cell reduces and it's electrical output drops.
This reduced output is used to trigger a smoke warning on the flight deck.
When the smoke clears the unit reverts to it's 100% light condition and the
warning is cancelled.
I
l 1
I 1
EXAMPLE - A 3 2 0 CARGO HOLD SYSTEM
I L
7--
-
t I
This system is if the dual loop type. Two detectors of the ionisation type (one
per loop) are located in the forward cargo hold, two in the parallel section of the
aft hold and two in the non-parallel section (six detectors i n total).
Testing of the smoke detectors can also be done by a push button on the
overhead panel.
--
Fig. 18 A 3 2 0 CARGO BAY DETECTION & EXTINGUISHING SYSTEMS
i 1
Fires can be caused by heat generated from the brakes. Provision exists on
most later types of aircraft to monitor the temperature in the wheel well in
terms of overheat conditions when the landing gear is up.
Temperature sensors are also fitted to the brakes to give flight-deck indication
of actual brake temperatures a t all times. (see the book in this series on
Wheels, Tyres and Erdces).
The following description is based on a Boeing aircraft. There is no need to
commit t h e details to memory, but you should know the principles and its
operation.
There is a single loop detector located in the each main wheel well. The
detectors are made by Fenwall, and are sensitive to temperature (resistive type
firewire). These detector elements operate by the reaction of their internal salts
to temperature change - the resistance decreases with an increase in
temperature. At a temperature greater than 400°F (204°C) the wire provides a
ground warning signal to the control card.
The resistivity of the salt drop a t this temperature and allows current to flow
from the source element (in the centre of the firewire) to the grounded outer
sheath. The elements automatically reset on temperature reduction.
The wiring is in two sections and connected in series to form each detector.
The two detectors are in turn connected in series and wired to the duct leak
and wheel well Fire Control Card.
The system will give a warning on EICAS (Engine Indicating a n d Crew Alerting
System) and turn on the wheel well fire light. In addition, the flight
compartment master warning lights illuminate, the discrete fire warning
illuminates a n d the flight compartment fire audio sounds.
Test
A test switch is located on the fire test panel. The switch is labelled
"WHL WELL" and when activated sends a signal to the control card. If the
control card is operating normally, and the two detectors are continuous, the
wheel well fire light illuminates along with the master warning lights, discrete
fire light, a n d fire audio.
Sensors are fitted to ducts taking air from the jet engine for pressurisation
1
purposes, de-icing, heating etc. I
1
1
The following system is based on a Boeing aircraft. Do not try, to remember the
detail b u t you should understand it and relate what you read t o what is fitted
to you'r +-craft. I / 1
--
A -
The system is divided into left and right zones. The left zone h a s five elements
wired in series: the left wing leading edge, the left air conditioning bay, the
wheel well, the aft cargo compartment, and the pressure bulkhead aft to the
APU.
The right system h a s two elements wired in series; the right wing leading edge
and the right air conditioning pack bay.
The two systems are wired to the duct leak and wheel well fire Electrical
Systems Card. If the system senses an overheat, it is enunciated a s a caution
through the warning electronics unit. It also annunciates the appropriate duct
leak caution light on the pneumatic control panel and a level "B" caution
appears on EICAS.
To test the system for correct operation, a test switch is located in the flight
deck. The switch is labelled 'DUCT LEAK'. A successful test illuminates the
two duct leak lights.
PNEUMATIC CONTROL
PANEL
------
RIGHT SYSTEM DETECTION
------
L (R) EICAS
, COMPUTERS
I
EICAS DISPLAY)
I I '
,
Fig. 20 BOEING P N E U ~ A T I CDUCT LEAK DETECTION SYSTEM
- i- -
,
It is fitted to detect fires caused by people putting their cigarettes out in the
waste paper bin. Smoking is not allowed in the toilets - nor incidentally when
walking in the aisles - s o it should not happen. Unfortunately it does, but not
often.
The bottle has two nozzles. These have a heat sensitive solder covering their
discharge ports. The bottle contains HALON 130 1 and weighs 2 pounds (0.9kg)
when full. When either nozzle temperature reaches 175°F (80°C)' the solder on
the discharge nozzle melts. The extinguisher agent is directed into the waste
container. This operation is automatic and has no controls or indications on
the flightdeck.
U(TINGUISHER INSTALLATION
Temperature Strip
I
The dots on thisfstrip are progrks,sively sensitive to heat. The heat will turn the
dots black in sequence. The strip is located /abovethe chute, behind the towel
slot.,After a fire, this strip must be repl5ced. Fires that exceed a critical
temperature will require a structural inspection of the chute compartment and
immediate area.
TOILET CUBICAL
The requirements of JAR 25 (for large aircraft) state that a smoke detector is
fitted in the toilet cubical to give a warning to the flight crew should anyone
smoke in the toilet cubical. The smoke detection system senses the presence of
smoke in the toilet cubical and activates an aural/visual alarm. The detector
is located in the ceiling.
The assembly consists of a sensor unit, alarm, horn and electronic circuitry.
The sensor incorporates a red alarm indicator to provide a visual indication
when smoke is detected. A green power indicator is provided. A powerlreset
button is fitted near the power indicator. The power supply is 28 volts dc.
blank
- 27
rnoodul II -940
-
POWER POWENRESET
INDICATOR SWITCH
(GREEN) \ /
DETECTOR FACE
SMOKE DETECTOR
-
, Fig. 22 TOILET
--
CUBICAL SMOKE DETECTOR
-
I '
I
I
LAVATORY CALL
LIGHTIRESET
SWITCH
CABIN SYSTEM
CONTROL PANEL
.- CABIN AREA
CABIN MANAGEMENT CONTROL PANEL
SYSTEM
-
r CHIME
I A V MASTER CALL
LIGHT
blank
MAINTENANCE - GENERAL
\
Control Units and Detector Heads
I 1
These may have to be removed irorn the aircraft from time tb time for bench
checks to be carried out. This will involve the use of special test equipment.
These tests will normally be cmriexout when specified in the AMM-and as an
acceptance check on a new component rece'ived from stores.
, , i
Fire Wire-- - - . ' - ~ .
-, , -~ ,
~ -~ ~- .-- - - .~
_,'
, -
Some fire wire is fitted within an armoured sheath to protect it from damage
but where the fire wire is not so enclosed it must be correctly supported in
rubber supports (to prevent chaffing) within special clips ("P" clips).
It is most important when fitting new lengths of fire wire to check that the part
number is correct - as many fire wires are very similar and the fitting of an
incorrect fire wire could have serious consequences.
All systems have a "press to test" or BIT facility. There may be one test button
to test the complete system or there be more than one, eg, one for the firewire,
one for the cartridge unit and one for the rest of the system.
It is important to note that for a "press to test" to show a satisfactory result all
the system that it is testing is working properly - for example, all power
supplies are available - to lamp and control modules (possibly a c & dc); all
appropriate control modules are working; continuity of firewires is satisfactory
and bonding connections are serviceable.
O n the electrical fire wire the "press to test" button grounds the resistive type
central electrode and causes current to flow operating a relay. O n the
capacitive type the "press to test" button increases the capacitance of the
system causing it to operate and give a warning.
On some aircraft the fire detection systems are monitored by on-board fault
computer--systems which can be accessed on the flight deck. -
-
I
I '
YOUR ACTIVITY
I
the following: \
'> I I
I
\
1. Are there fire detecfiqn/smoke detection systemslfitted to all those
areas mentioned in this book? If not why not?
I
2. Any that are fitted, are they similar to those described in this
book?
Page
Maintenance I ?7
Airbus aileron system I 28 1 I
Airbus elevator system ' 30
- - -
1' I
-
Ruddqr system 30 \ 1
rnoodull IA-944
POWER FLYING CONTROL UNITS
(PFCUs)
ANSWER Because of the speed of the aircraft and/or the size of the control
surface the aerodynamic loads imposed on the control surfaces are
too great for the pilot to overcome manually. So the controls are
powered on l a g e l f a s t aircraft - usually hydraulically.
As aircrait have got larger and/or faster,so,v and/or s in the tormula have got
greater with a resultant increase in aerodynamic loading.
' I
These'lohds are likely to be in ~ x c e s sof thoke which could be ~ornfoytably
accommodated by the pilot. To assist-the pilot in overcoming these L.- 1
loads some
form of powered operation of the Fontrol&rface is essential. W ~ t hfully power-
operated controls the normal forms of aerpdynamic a s s i s t a k e , ie aerodynamic
balance, spring balance etc are not effectike.,
1
I 1
herd a control system is fully,pbwered thd pilot has no feei of the
aerodynamic loads on the control surface:'~herefore he/she c s n o t
instinctively position the control surface in relation to the speed and altitude of
the aircraft. If through the lack of such control, rapid movement is applied to a
control surface, the surface may be damaged, the airframe may be over-
stressed or the aircraft may become unmanageable. The pilot must therefore be
given some indication of the aerodynamic forces on the control surface by an
artificial feel system incorporated into the control system.
(a) Valve R a m Type. This consists of a servo valve and ram assembly supplied
with hydraulic power from the aircraft's hydraulic system.
(b) Self Contained Wpe. This consists of a self contained unit with its own
hydraulic system with an electrical supply from the aircraft's electrical
system to operate the hydraulic pumps. Also contains servo valves and a
ram assembly.
General Principle
The pilot moves the controls and that movement is transmitted to the PFCU b
2 111eckl~6i~d system (pi--ish/p~=~l_l
Fcl_s, ca-hl~setr) to n p ~ r a t ethe sprvo valve; or
a fly-by-wire system (an electrical sign& to an electrically obeiated servo valve),
or a fly-by-light system (the signdl transmitted by light to be c,onverted:to an
electrical signal to operate an electrically operated servo valye).
1 I
I
When ;the pilot moves the controlkihYdr<ulic servo valve i$ selected in the
PFCU a d d the PFCU output jack \ram) 'st&ts to move. As soon as the output
jack staits to move its movementis felt b i c k a t the selectorservo valve - and it
tries to de-selecf {he servo valve. This is called "feedback.
,
1 - I
-
QUESTION Thei-e are two types-of feedback - negative and positive. Do you
happen to know what sort this is? (1 minute)
P l L o r s INPUT SIGNAL
SUMMATION DEVICE
. ACTUATOR1
JACK
(b) Stability - The system must remain stable and uninfluenced by any
signals which do not originate from the pilot. To maintain stability it is
essential to ensure that the linkage is free from backlash, that the
dampers function correctly and that the hydraulic system is free from air.
(c) R i ~ d i -t Flexibility
~ in links and anchorage's must be eliminated.
(' (e) Pilot's feel - In power operated systems feel must be provided by artificial
feel units. On power assisted-systeqs the arrangement -,I of-the linkage
provides feel (proportion& feedback). \-
I I
(f) Emergency Measures - There must be provision for alt$Aative methods of
control so that in the evenf df a rnephdnical failure of t h e PFCUlthe pilot
/
will!still be able to control 'the-&-craft.
1 There can includk: ,
I
\
-- /, /
_,
(2) Duplication of ~ o m L o n e n t s ~ - ~ l ithere
& - e are more th& one PFCUs
operating each control surface, each with its own hydraulic supply.
Interconnected via spring rods.
With reference to figure 2. The unit comprises a jack body connected to the
control surface, a n equal area jack ram connected to the structure, and an
integral servo valve connected to the pilot's control. When the servo valve is
neutral the delivery ports are closed and the fluid is trapped in the jack body so
that the jack is hydraulically locked and there will be no movement. When a n
input signal is applied t h e servo valve moves to open one port to pressure and
7
RETURN
1 PRESSURE /
~-
SERVOVALVE
~
-
-- - -
PILOTS INPUT
-
OUTPUT TO
CONTROL SURFACE
STRUCTURE
JACK RAM -
Fig. 2 VALVE RAM TYPE PFCU
This 'follow up' of the jack body is the negative feed back of the system. So long
a s the pilot keeps the input going so the selection will be maintained and the
control surface will continue to move. But as soon a s h e / s h e stops the jack
body will catch the pilot's input servo spindle u p and cancel the selection. This
amount of movement is very small and takes a fraction of a second.
The same PFCU can be mounted in two ways so a s to give either fully powered
operation or power-assisted operation.
Power Assisted Control (figure 3)
In this type of control the input link and the output link are connected in such
a way t h a t some of the loading felt by the control surface is felt by the pilot.
Thus the pilot h a s some feel.
When the pilot's control is moved it causes selection of the servo valve which
causes the PFCU to move. The loading felt by the control surface is also felt
back through the jack ram onto the pilot's input lever. The pilot will feel a
proportion of this loading this in the ratio a:b. To enable the system to work
there i s usually a lost-motion bush (a bush with a small amount of play in it)
a t the connection of the jack ram to the pilot's input lever.
TO CONTROL
SURFACE
With controls fully power operated the whole of the force needed to operate the
control surface is provided by the power system (hydraulic).Movement of the
pilot's control column moves the control rod of the servo valve. The servo valve
then allows fluid under pressure to operate the hydraulic jack and so move the
control surface. As all the effort to move the control surface is supplied by the
hydraulic jack, the pilot h a s no feel of the loads on the control surface. Feel
therefore m u s t be provided artificially, eg a spring or Q feel unit.
The systems shown in figures 2, 3, 4, 6, 7 & 8 use a PFCU where the body of
the unit moves the control surface while the jack ram is attached to the
structure. With some PFCUs this is the other way around (figures 5, 9 and 10).
When the jack ram moves the PFCU there is a "summing link" between the
pilot's input and the PFCU output which is in fact, the negative feed back link.
CONTROL COLUMN
HYDRAULIC
fl RETURN PRESSURE
PIVOT
-
1
U
PFCU
-
SERVO VALVE
RETURN -LSUPPLY INPUT LINK PILOT INPUT
I
C 9 C----L
S~RUCTURE 1 1
/SUMMING LINK
1
, ,
-
b
A
I
1 PFCU OUTPUT
-
PFCU I \
I TO CONTROLS
I
With reference to figure 5. When the pilot puts an input into the PFCU the
summing link will initially pivot above point A on the ram. This will cause the
servo valve to select to move the ram. The movement of the ram will be in suck,
a direction as to try to de-select the servo-valve, so as soon as the pilot stops
his/her input the jack ram will de-select the servo valve via the summing link
pivoting about point C. Example:
moodull l
-6-
A-950
Note. The simple summing link shown here is normally a set of links so
arranged as to allow for the incompatibility of the range of movements
between the jack room which can be, say 8 to 12 inches (50mm to
305mm), and the servo valve which is in the range of 0.030" (0.7mm).
Manual Reversion
Some PFCUs have a manual reversion facility. This allows the pilot to operate
the controls manually should the PFCU fail. Manual operation will be heavy
with reduced control authority but it is a reliable emergency standby measure.
PILOT'S INPU
HYDRAULIC FAILURE
(PILOT'S INPUT LEVER LOCKED,
FLUID BYPASS VALVE OPEN)
-
I
-
,- L
I
I
' 1
When manual reversion occurs the pilot will move the control surface directly
via the PFCU. In this case the unit just acts as another link in the system. The
PFCU goes into manual mode by:
(a) Disconnecting the jack ram from the structure. The jack ram is connected
to the structure by a hydraulically operated lock mechanism which
disengages automatically to allow the jack ram to slide freely back and
forth. The pilot's input, via the servo valve, moves the complete PFCU
including the ram to move the control surface direct.
(b) Allowing fluid to transfer freely from one side of the jack ram piston to the
other by a hydraulically operated transfer valve. Both sides of the jack r a m
piston are connected together hydraulically by a valve which is normally
closed. When normal supply pressure fails the valve opens and allows free
movement of hydraulic fluid from one side of the piston to the other (figure
6). The pilot's input causes the servo valve to move the jack body direct
and it slides u p a n d down the jack ram.
In both cases the pilot's input is via the servo valve input and the PFCU moves
in response to the pilot's force t h u s moving the control surface. In other words
the PFCU acts as a control link between the control system and the control
surface, and h a s no other function.
The following is a brief description of the PFCU as fitted to the BAC 1- 11. There
is no need to commit the details to memory but you should be able to
understand the operation and-relate this to what h a s alregdy been said.
I \
I
The uAit shown in figure 7 is ohe of a pair khich together operate the rudder.
Each unit is fed by a separate dydraulic supply from the aircraft.
! ' /
I
Individual flying control input <ohne~tion$via spring strut4 pbrmit bperation of
each unit even though the other has failed and each unit isi capable of
operating the rudder on its own. /
I
Pressure Off. The by-pass valve provides a fluid way to both sides of the jack
ram via restrictors so the PFCU body will move, operating as a virtual control
link with gust dampers. To prevent cavitation under such conditions, the
suction NRV (Non Return Valve or Check Valve) opens to permit fluid flow frc
the return line.
Pressure On. Pressure action on the by-pass valve closes it against its spring,
shutting off the by-pass flow. The supply NRV then opens and delivers fluid to
the rotary control valve moved by pilot input.
Input selection, as shown, opens u p one side of the jack to pressure and the
other to return and the jack body moves in the direction shown.
Once input ceases, the body will catch-up with the input, returning the rotary
valve to the neutral 'off position and a hydraulic lock occurs providing
irreversibility.
Emergency
Hydraulic System Failure. The failed unit reverts to by-pass condition and is
driven by the remaining operative unit.
-. g -
rnoodull 1A-953
Stuck Valve. On pilot input the spring st,rut will collapse i n the appropriate
direction permitting full travel of the remaining PFCU rotary control valve.
At the same time the micro switch is activated by the spring and roller bearing
in the groove. This switches on a cockpit warning light and closes a pressure
shut-off valve in the supply to the failed unit, which then reverts to the by-pass
condition (as in hydraulic system failure).
The unit shown in figure 8 is one of the pair of units which operate the
elevators. It is virtually two rudder units in a common case with two rotary
valves and two input spring struts. Its operation is basically similar to the
rudder units described in both normal and emergency.
%STEM I [' m 2
SUPPLY RENRN -- . \ SUPPLY RENRN -
SUPPLYPRESSURE O F F
musl
-
-
W U I I L ClRCUrr
BYPASS OPEWnDNl
-
Two System Failure in Flight. Controls revert to manual. Left hand by-pass
valve held in intermediate position by undercarriage controlled solenoid,
provides unrestricted by-pass as does right hand one. Input signals continue
until the input connection a b u t s the input stops and so connects input to
output.
Most modern PFCUs a r e similar in principle with the majority of servo valves
being of the slide type. With a Fly By Wire PFCU (A330) as shown in figure 9
the slide valve is moved by a solenoid operated hydraulic jet type valve (servo
valve). The solenoid gets its signals from a flying control computer. Note also
that the PFCU h a s a futed body with the ram moving the control surface and
feedback being provided by the feedback linkage from the ram to the servo
valve.
--- 7
-
I SUPPLY RETURN i
\ A
I
LECTOR
ATTACHMENT
TO
FEED BACK LINKAGE
RAM CONTROL
THE STRUCTURE SURFACE
These are less common than the valve ram type. They are self contained in that
they have no external hydraulic power supplies. Internally they have their own
complete hydraulic system to include: pumps; valves; reservoirs; pipelines;
jacks, etc built into the one case. The only external connections are electrical
and the control rods (input and output).
SPRING BOX
INPUT SPRING
- - - \
CONTROL SURFACE
1
I
I \ Fig. 1 0 SELFI CONTAIN,ED TYPE PFCU ~
SERVO 8t MAIN PUMPS
I
Figure 11 shows a general view of the PFCU as fitted to the VC 10. Note the
attachment of the body to the structure; the pilot's input link; the jack ram
connection to the control surface and the feedback link to cancel the pilot's
input.
ARTIFICIAL FEEL
/'
Since the control load is now taken from the pilot and all he/she has to do is
move-the yalves of the various PFCUs; there is no "feel"of;the loads on the
control surfaces, and it is thereforeplikelythat the pilot will'ovler-control and
overstress the aircraft and/or the control sjistem.
I
I
Various types of synthetic feel devices ar,e used to simulate control surface
loadings. They vary in effect aria comp16@y depending on the aircrddt
-
'type.
Sometimes feel is not provided onpt= -aileron system. I -- ,,
I
I 1 \\ ' I
I
1
Spring Feel I I 1
' I 1
I
,' L--/'' I
I
.I
' \
with-; spring-feel unit the pilLt pulls (or-pbshes)on a sp&ng.- he spring may
be placed directly in line with the control linkage (as shown in figure 12) or it
may be placed "outside" the control run as shown in figure 13.
SPRING BOX
\ /
SPRINGS
\ -
CONTROL SYSTEM
MOVEMENT
STRUCTURE
SCREWTHREAD
\
Fig. 12 SPRING FEEL UNIT - 1
A s the unit moves so it will move the complete system - via the springs - to a
new neutral setting - thus trimming the aircraft.
Figure 13 shows a more common method of connecting the trim actuator to the
flying control system.
- 13 -
rnoodull l A-957
CONTROL COLUMN
TO FLYING
CONTROL
SPRING FEEL
UNIT
"Q" Feel
- (figures
- 14, 15 & 16),
' ip -', I\ \I
I
I I
ANSWER Advantages: *I GGhh'' ee a p .
I ,
fI UlSllL. ,
-Light. \ r
r
-
-
,
* Maintenance free. 1 1
I
1
~ i s e d v a n t a ~ (one
e s ar least). The force is constant in relation to
I - airspeed and therefore_t&es'no account of how fast the aircraft is
i
DIAPHRAGM
ANSWER It got it's name "Q" from the formula q=%pv2. I t is the dynamic
equation and capital "Q" is used for "Q feel".
- 14-
rnoodull l A-958
A device which gives the pilot feel proportional to "q"is the "Q pot". Used on a
number of aircraft, its popularity arises from its simplicity. A disadvantage it
possesses is that because of the small pressures involved, large areas of
diaphragm a r e necessary to extract any useful force from the unit directly.
This is similar in principle to the Q Pot except that the dynamic pressure i s
increased hydrau~callywhichthen allows for the construction of a smaller
unit; -
I
PlTOT
PRESSURE
Construction
A loading jack, connected to the pilot's control in such a way that it extends
whenever the control is moved from neutral, is fed with hydraulic pressure in
direct proportion to dynamic pressure. Pilot stick force is t h u s also
proportional to "Q".
Operation
The hydraulic spool valve is a t all times balanced between a down-wards force
from the diaphragm (Pitot - Static = Dynamic) and a n up-wards force due to
signal pressure on the spool valve, which is trapped between it a n d the loading
jack. A s velocity increases so does dynamic pressure a n d the spool valve i s
pushed downwards, admitting supply fluid so that signal pressure increases.
However, a n increase i n signal pressure also increases the up-load on the spool
valve, until it i s returned to the neutral position. Signal pressure is now again
proportional to the new dynamic pressure.
A control movement causes a n increase in the signal pressure line (the links
are so arranged that a control push or pull always causes the loading jack to
--
Signal pressure, against which khe pilot is always having to lwork to move the
controls, is therefore always prdcisely proportional to the dynamic pressure
acting on the control surfaces.
I
Trimming
Since the control surfaces are now made irreversible by the-PFCUs normal
trimming by means of tabs is not possible.
Note. Longitudinal trim systems on most large aircraft make use of a trimmable
tail plane (stabiliser) which works independently of the normal flying controls -
for most aircraft.
In figure 12 the whole spring unit can be moved to the left or to the right by t h e
operation of the screw trim wheel-connected by trim cables from the flight deck
or electrically operated. The systems in figures 13 and 16 use electrically
operated trim actuators. Study the drawings and make sure you understand
how the systems work.
QUESTION Where is the feel unit located in the flying control system? (2 mins)
ANSWER Between the pilot's input and the next unit down stream in the
system - on most aircraft this would be the auto pilot servo - but
on some aircraft it is the PFCU.
STATIC PlTOT
CONTROL COLUMN
STRUCTURE
CONTROL
SURFACE I
-1 @- -
,
PFCU
I
Fig. 16 TRIM ACTUATOR/WITH Q FEEL UqIT 1
- - / I /
/
,
I -- -.. \
I \ 1'
THE AUTO PILOT SYSTEM r
I / I
The auto pilot (Alp) system is capable of holding the aircraft qn any selected
headirig bd.the aircraft will retuqn_t thhat heading if displdcdd from it. The
A/P keeps the aircraft stabili&d-in-flight,&d accepts navigation commands for
course headings etc. It will also fly the aircraft to an automatic landing. On
some aircraft will also control nose wheel steering.
Principle
With reference to figure 17. In principle the system is made u p of an outer loop
and an inner loop control system. The outer loop control is a non-feed back
loop and is made u p of inputs from the pilot and other systems such as
navigation systems etc. These signals are sent for computation before going to
the inner loop computer.
The inner loop system consists of two negative feed-back loops. The
aerodynamic coupling is connected with the aircraft movement and is sensed
by rate and displacement gyros. Both gyro inputs send signals to try to negate
or cancel the effect of the original command signal.
The other feed-back signal is servo actuator position (or control surface
position) being fed back to the A/P computer - trying to negate the original
servo signal input.
I -
AERODYNAMIC COUPLING
d
I
FEEDBACK SIGNAL
C
INNER LOOP
I
INNER LOOP
OUTER LOOP
MODES
-
- MECHANICAL CONNECTIONS
ELECTRICAL SIGNALS
OUTER LOOP OUTER LOOP
COMMAND
COMPUTATION
CONTROL
I
Fig. 17 INNER & OUTER LOOP CONTROL
I
II ~
On many aircraft one cornputef (bften duplicated) will cany; out all the
computations-for both loops. - -- --
General
The purpose of the A/P is to reduce the fatigue of the crew on long flights by
taking over the routine flight control of the aircraft. The pilot can engage and
disengage the A/P at any time. If he/she wishes to change the attitude/
course/altitude of the aircraft whilst the autopilot is connected he/she may
disconnect the A/P and fly the aircraft manually to the new attitude/course/
heading and re-engage the A/P (allowing for A/P input corrections), or he/she
can select the A/P to do the task via the A/P mode control panel.
Auto pilot control can provide for one, two (usually elevator and ailerons), or
three axis control (lateral - ailerons, longtudinal - elevator a n d directional -
rudder).
- 18-
rnoodull l A-962
One A / P can be selected on the ground provided the engines are not running.
Once a n engine is started the A/P is automatically selected out. Once airborne
the A / P can be engaged 5 seconds after take-off.
-
GYROS
COMPUTER
AUTOPILOT
SERVO PFCU
CONTROL
CONTROL
PANEL
CONRTOL SURFACE POSITIONAL FEEDBACK
A
Fig. 18 BASIC A / P SYSTEM
The gyros and other sensing equipment develop signals which a r e processed in
a computer and the resulting signal is sent to operate the autopilot servos. The
output from these servos moves the appropriate flying control system PFCU to
move the control surface. There is feedback from the servos to the computer
(not shown in the drawing).
The PFCU will move the control surface and a (negative) feed back signal is
sent to the computer. At the same time, as the aircraft moves, so the gyros will
pick u p this movement. This aerodynamic coupling will provide another
negative feedback signal to the computer to control the rate a n d displacement
of the control surface.
The Three Channels (figure 19)
This shows in more detail the various inputs to a typical A / P system. The
summation devices (shown as a cross within a circle) are parts of a computer
where the various input signals are worked on and summed before being
outputted. The output signal is amplified before being sent to the A / P servo
motor (which could be a hydraulic actuator).
There are two main signals for the rudder channel which will determine when
a n d how much the rudder will move. The first signal is a course signal
obtained from a gyro compass system. A s long as the aircraft remains on the
heading that it was on when the auto pilot was engaged no signal will be
produced. Any deviation will cause the gyro compass to send a signal to the
rudder that is proportional to the angular displacement of t h e aircraft.
The second signal received by the rudder channel is the rate signal. This signal
is proportional to the rate of turn. The faster the aircraft is turning the stronger
will be the signal. This comes from
--
a rate gyro.
- -
PITCH,
CONTROL
POSITIONAL FEEDBACK ~
WHEEL
I
PITCH
I
RATE --
I
GYRO
I l i
VG 1
PITCH '1
1I
I / I
ALTITUDE
&SPEED
CADC , I 1 I
ROLL SERVO
YAW
YAW SERVO
SENSOR
- 20 -
rnoodull l A-964
These two signals are combined, processed, and amplified (in a computer), and
the resulting output is sent to the rudder servo. This will turn the rudder in the
correct direction to bring the aircraft to the correct heading.
As the rudder moves a feed back signal is sent back to the amplifier. This is a
negative feed back signal and is summed with the input signal (from the gyros).
When the two signals are equal the rudder has reached the desired position,
the output to the rudder servo stops and the rudder movement ceases. The
rudder will stay in this selected position until the aircraft is in the new heading
when the reverse will happen.
There is a cross feed to the aileron channel to produce the correct amount of
bank for any given rudder deflection.
The aileron channel receives it's signals from a roll rate gyro which may be the
gyro horizon indicator (on older aircraft), the turn control (on the flight deck)
and navigational computers. There is cross-feed to the rudder for co-ordinated
turns.
-- --
-- . -
- -- -- -
I
- L
When .commanded the ailerons m6-d a feed back signal iCproduced. This
signalis summed, and when equal to thd input signal the obiput s i h a l to the
servo Leases and the ailerons stab moving. To keep the airckaft in a bank some
aileroh $dl have to be maintained which'is carried out by signal summation.
I /' 1 1 /
I i 1
On return to level flight the inpLtsignd\td the servo becomesismallei and the
feed back signal begins to movk +e ailerons back to the t r d l position. A s the
aircraft reaches the lateral position so the1ailerons should reach their trail
\
' I
--
1
--
I
- ,-'
t
i
- 1
I I \
Figure 20 shows the general arrangement of an A/P system. Study the drawing
and note the various data links and that on most systems there would be
duplicate A/P servos.
This is manually operated to set the various parameters and cause the aircraft
to perform manoeuvres. Additional command signals can be sent to the A/P
Flight Director computer from the INS, VOR, ILS, and D A D C etc. The A/P
system may be co-ordinated with Stab Trim, Mach Trim, Yaw Damper and
Thrust Management systems. The auto pilot can be engaged and disengaged
electrically or mechanically depending on the system.
While the autopilot is engaged, operation of the controls on the flight controller
will cause the aircraft to climb, dive, or carry out a co-ordinated turn. The
engage switch is used to engage or disengage the autopilot, and there is also a
disengage switch on the control column.
COMMAND SIGNALS
Sensing Elements
The directional gyro, turn and bank gyro, attitude gyro, rate gyro, and altitude
control are sensing elements. Though signals are generated from other gyros
on most modem aircraft. The gyros are usually laser operated, housed within
units in the aircraft and are duplicated or sometimes triplicated.
Note. For details of the operation of the mechanical and laser gyro refer to the
book entitled "Instruments" in this series.
The Computer
The computer will then "work" on this digital information. But for most systems
outside the computer system this digital information is useless. So for the
digital information to, say, drive a servo motor in a control system it must be
converted back to an analogue signal and amplified. This is carried by a D/A
converter. We then have a n ordinary analogue voltage/current signal that can
be used to drive motors, relays etc.
-- - - --
1
I
'_
compute& on aircraft pertor&functlons such as:
I
I
* A power supply. I I / 1 I
I -
Servos
I I
Note that when the servo is connLcted in such a way that its h p u t moves the
whole flying control system (including the controls in the flight deck) it is called
a parallel system. When it is connected in such a way that its input only affects
the flying-control system "downstreamn-(thepilot's controls do not move) it is
called a series system.
The same principle apples to trim actuators and yaw dampers but yaw
dampers are always connected in series.
__C
PILOT INPUT
-
ARTIFICIAL FEEL AUTOPILOT SERVO
n
1
m
I
PFCU
I L
CONTROL SURFACE
Operation
In the electric type the motor of the servo is connected to the output shaft
through reduction gears. The motor starts, stops, and reverses in response to
command signals from the computer.
In the electro hydraulic type a valve is caused to operate by signals from the
computer. This will cause fluid under pressure to pass to a jack (part of the
servo) which will cause the controls to move.
The servo may be a separate unit or combined with the PFCU and is usually
duplicated with each unit being connected to a different hydraulic supply. In
many cases when one unit fails the other will continue but with half the
authority.
With reference to figure 22. The control system is connected to the servo via the
output crank and internal crank. When the A/P is disconnected the two detent
pistons are withdrawn by spring action from the roller and these cranks move
freely when the system is moved by the pilot.
When the A / P is selected the detent pistons move in to engage with the roller.
In thts condition hydraulic pressure supply is fed to the servo-piston to move
i
the control system via the cranks. .T?iis-pressure suppiy iscpntroiied by the
EHSV under command from the A / P codputer. The output ipgsition'LVDT
(Linear Variable Differential ~rdnsducer)se$ds positional feedi back data to the 1
compute^. i
I ,
- -. \
1 ELECTRO-HYDRAULIC
SERVO V F V E (EHSV)
REGULATOR
Alp SERVO
POSITION LVDT
SERVO PISTON
CENTRING SPRING
SOLENOID1 VALVlI 2
--. ..-..-I V- -n T.
.POSITION -..,------. --.-..,
rlvul run uu.--, ,-
(RUDDER DETENT ENGAGE)
lNTLw
1
"
fi
...-.--.,.
I r u I wwNn
LLCRANK
IN ICtXfMP
SERVO V A V E
SOLENOID VALVE 1
\ ELECTRICAL
/CONNECTOR
CRANK OUTPUT CRANK
TO PARALLEL
RUDDER SYSTEM
\Alp SERVO
FILTER COVER POSITION LVDT
OUTPUT CRANK TO
PARALLEL RUDDER
CONTROL LINKAGE
LVDT
The PFCU a n d the A/P servo are both housed in the same unit.
A/P disengaged. The pilot's input goes in a t point B of the input link which
pivots about the (at present) fmed pivot A. This causes the push/pull link to
move t h u s selecting the main servo valve. This causes the main jack to move
and a t the same time cancelling (or trying to) the main servo selection. When
the pilot stops his/her input movement the main jack will continue to move,
t h u s moving the link about pivot B. This will cancel the main servo selection
and the main jack will stop. This follow-up movement takes but a fraction of a
second. (negative feed back).
A/P engaged. With auto pilot on, hydraulic fluid pressure is fed to the
autoflight control jack under the control of the autoflight servo. This will move
the link (about point A) via the summing links to select the main servo as
before. Feed back to cancel the signal is similar to that described above.
-
.
RETURN HYD SUPPLY
i- ! INPUT
I a ,
I I I \
MAIN JACK FEEDBACK LINK
Note that the drawing does no show a by-pass valve (omitted for clarity). In the
event of hydraulic failure this would open automatically and allow fluid to pass
freely from one side of the main jack to the other. The pilot would then move
the control surface direct by moving the main jack.
QUESTION When the auto flight control jack moves what happens to the pilots
input? (5 mins) (figure 23)
ANSWER The pilot's controls will move as well. So when the auto pilot is in
operation the cockpit controls will move.
SYSTEM MAINTENANCE
S .
.
i
Q G ~ I CXG ~~ ~ Z C C Z I C Z ~
and modifications. The followink is general jnformation andirgferende must
always be made to the AMM. I
I ,1 '
1 i I
' I
/
\ . 1
~
-/
System Functioning r --
-1 ' , /
, ", I- -
r'--
-
4
rnoodull l A-971
13. Check any BITE systems and any faults stored in the fault computer .
14. Check that all visual and aural warning systems work correctly.
15. Switch off system, check freedom of controls, a n d check for leaks.
16. Carry out duplicate inspections if required.
17. Re-configure aircraft.
18. Record all work in the Tech Log or work cards and sign.
Note
Most large aircraft have Flight Director Systems, Inertial Navigation Systems,
Inertial Reference Systems (INS/ IRS), and various other navigation systems.
These will all have test procedures stated in the AMM.
These are compatible with the Auto Pilot System and may control:
I
I
(e) ~utoianci. \ \ I
Figure 25 shows a schematic of the Airbus A300 aileron a n d roll control spoiler
operating system. Only one side is shown as the other is the same, except for
the fitment of an A/P servo. While there is no need to memorise the system you
should have a good understanding of it's operation and should be able to relate
the principles to your own aircraft/aircraft experience.
Note the following:
JC
The selection (on the down going wing - u p going aileron) of the roll
control spoilers by the operation of the pilot's handwheel via the
EFCU (Electronic Flight Control Unit). The handwheel also
operates the ailerons of course.
* The inputs a n d outputs to the EFCU - in particular the input from
the ADC (Air Data Computer) and the output to the ECAM
(Electronic Centralised Aircraft Monitor - for flight deck displays).
The Droop Actuator (2). Sets the ailerons to the droop position for
take-off and landing. Gives extra lift similar to a trailing edge flap.
Automatically set when the leading edge slats are selected. Does
not prevent the ailerons from working in the normal manner, but
biases the whole system so the ailerons on both wings are set
lower than the trailing edge of the mainplane.
It does this by changing the position of the pivot a t the trim screw
jack position.
* The Differential a n d Droop Unit (2), which s u m s the inputs from
the flight deck handwheel and Droop Actuator.
* Three servo control actuators or PFCUs per aileron - each with its
own hydraulic supply.
* Five roll control spoilers sharing 3 hydraulic systems.
* Aileron Position Transmitter to ECAM.
* Autopilot Roll Actuator (A/P servo). One unit with two hydraulic
supplies (Green and Yellow). When engaged the right-hand side of
the system is moved via the right-hand Differential and Droop Unit
and the left-hand side is moved via the flight deck controls and the
left-hand side Differential and Droop Unit.
,
- -
I
I \
J;
Operation of the tAmXvsteem; Operation of the switch in the flight
I
deck causes the motor to operate screw jacks via a cable system to
set the whole systemto a new neutral. 1 1
1
L.-.-.-.-.-.-.-.J TRANSMITTER
blank
-
1
Fig. 27 RUDDER SYSTEM
\
I I
i
I
I
I
I
I
I I I
1
~ 7 6 SYSTEM
7 1 -
I
--
I
Figure 29 shows the general &,a&ement ,of the 767 rudder1 system and figure
2 8 shows a simplified schematic arrangement based on the ,same system.
It is a fully powered system u s i & 3 PFCUs each with it's own hydraulic supply.
- - -
- - - --
, --
ELECTRICAL COMMAND
0= PNOTS FIXED TO AIRFRAME
- PlVOTSlLlNK CONNECTIONS
I
= PUSHIPULL RODS
BELLCRANKS
'
&FEEDBACK SIGNALS
H~RAUL~
SUPPLY,RETtJRN
C
CENTRING UNIT
STRUCTURE
REGULATOR
i HYDRAULIC SUPPLYIRETURN
t
ELECTRICAL COMhWND
8 FEEDBACK SIGNALS
Most units throughout the system are either duplicated or triplicated (on some
aircraft there are two rudders - which move together normally, but one will
move on its own should the other one become jammed or inoperative for any
reason).
Artificial Feel
Provided by a spring unit. With reference to figure 28, when the pilot moves the
rudder pedals the cables will move and cause the push/pull rod to move link 1
about pivot B to cause the rod to move into or out of the feel unit - pushing
against a spring and providing feel for the pilot.
Movement-of the rod will alsomove link3 about pivot D. This will cause
push jpuii roci ZF .to move iink 4 aboui H. Tnis wiii pui an-inpui inio ihe servo
valve of the PFCU causing it to move. ' I
/
I
I /
/
1 1 -
RATIO CHANGER
FEEDBACK TRANSM17TER
FEEL 8 CENTRING
DEVICE
\
UDDER AUTOPILOT SERVOS
(LEFT, CENTRE 8 RIGHT)
This is provided by an electric actuator attached between the structure and the
artificial feel unit. Movement of the actuator will cause link 2 to pivot about A
moving the feel unit to the left or to the right. This will set the whole of the
system to a new neutral, change the position of the control surface and hence
put a trim input to the aircraft.
Autopilot Servo
When engaged (using an analogue signal) detent pistons move to lock onto' the
main servo piston using hydraulic pressure. Signal commands (analogue) from
the A/P computer selects hydraulic fluid to one side or the other of the main
servo piston and it will move. This will move the push/pull rod and cause link
3 to pivot about D a n d cause the whole of the system to move. This movement
will put an input into the PFCU servo causing the rudder to move.
-
Yaw D,arnper
To try to combat adverse yaw associated with Dutch Roll, y a y dampers are
fitted. When Dutch Roll occurs: sensors (&os etc) will send signals to a
computer which will send a n analO@e signal to the yaw d h p e r servo. This
-- -
Thus, during Dutch Roll conditions the rudder will be gently moved
continuously from side to side by a-small amount. This actionl will significantly
reduce-the-effects of Dutch Roll.- - -
-
The cycle will now repeat itself with the aircraft gently rolling and
yawing from side to side. This 'falling leaf' type of motion h a s a
frequency of about 1 to l/z Hz. There is generally no loss of altitude
during this condition.
So yaw dampers are fitted as a form of active stability - using
sensors, computers and powered servos - to counteract this
oscillating action.
Ratio Changer
This device progressively reduces the range of the rudder with increasing
airspeed. Some aircraft have variable stops for the rudder that are related to
airspeed, some have fixed stops that are adjustable on the ground only.
Shows the position of the rudder on a CRT screen EICAS (Engine Indicating
and Crew Alerting System). Most large aircraft have a system to show the
position of the control surfaces.
-- - -
,
- - -- .
I
767 YAW DAMPER SERVO
-
i , I
The yawdarnper system connehed to the rudder powered Qiflg control system
provides!commands to damp ahy'undesired yaw and to provide turn co-
I
ordination (figure 3 0). -
I --
\ /
,
--
With most aircraft two yaw damper servos are provided and they work in
parallel, each with it's own indqpendent input using data fro& it's own yaw
damper module. When workingi together their inputs are summed and if one
works on it's own then the range
- of movement is usually h&d.
-
- ;--
-
I
Control Panel
Situated o n the flight deck, it provides for system disengagement and inop
status indication.
This is usually duplicated and takes data from the ADC and the inertial
reference unit to derive rudder commands. Signals are sent as analogue
electrical signals to the yaw damper servo. The module monitors system
performance, provides for manual selection and allows for automatic system
testing. Displays are on the front of this module, in addition to the control
panel, show test results.
v
PRESS TO TEST SIW
CONTROL PANEL
-
115V ac
-----c
POWER
SUPPLY
MODULE
WEIGHT
SWITCH
b L
-
r
pc YAW DAMPER MODULE
TAS
PlTOT PRESSURE
A OF A
FILTER
SOLENOID
VALVE
IHYDRAULIC
SERVO
1 ~&LG
I GYRO ROLL RATE & I I
ATTITUDE. YAW RATE.
LATERAL ACCEL
HYDRAULIC
I
GROUND SPEED
- SUPPLY --)
- --
I - - I 1-1 I I
POSIT1
LVDT
I 1
DETENT &CENTRING
I SERVO PISTON
1 MECHANISM
,
i
Fig. 30 767 YAW DAMPER SYSTEM 'i
I '
I I I
1
Analogue electrical commands from the yaw damper modules control hydraulic
pressure to the servo piston (ports C1 and C2) and movement of the piston,
which is in series with the rudder control system.
ELECTROHYD
SERVOVALVE
VALVE
POSITION
LVDT
switch circuits. /
I
e l i 1
I -,
I .\\ I r
~escri~tion I
I I
' I
A failure warning lamp on the flight engineer's panel is associated with each
PFCU aridpis dperated by a pre&ure-switch within the u n i t , ' ~ h e s elamps are
parallel-connected to t h e centralised warhing lamp and the--aural warning.
A failure warning lamp is also associated with each of the two feel simulator
pump motors. These lamps, which are mounted next to the centralised warning
lamp on the pilot's centre panel, are parallel - connected to the aural warning
circuit only.
The aural warning is isolated from the centralised warning system under flight
conditions by the action of the weight switches.
Operation
In each warning unit there are three separate channels, each comprising
relays, and rectifiers. Two PFCU low-pressure switches connect to each
channel and as aLl channels are similar only one is described.
When the low-pressure switch within a PFCU closes, a supply is passed to its
associated warning lamp. The same supply is paralleled to:
1. The appropriate channel within the associated warning unit. The ligb t
,_remainingON untilcZiGelled by the lamp cap being pressed, or the
r -7 --
I fault rectified. The centralisedtvahming lamp goes out but the
' individual PFCU lamp itays ON.
2. The rectifier unit. This allows a supply to the throttle operated micro
switch. When take-off rprn isselected the supply 4s sent to the weight
switch operated relay- and if the aircraft is on the ground the aural
warning and lamps operate.
I
I
The shpply cirduit (for the PFCU) low preisure warning swiich operates in a
similar way.' .-- -
- --
- -
If the control surfaces are incorrectly positioned for the take-off configuration
when take-off rpm is selected, micro-switches operated by the control surfaces,
or their associated controls, operate the aural warning.
If the aircraft is on the ground the supply is connected to the aural warning.
Thus the aural warning can only operate when a primary flying control surface
or a secondary flying control surface is incorrectly positioned and take-off rprn
is selected whilst the aircraft is on the ground,
FLY-BY-WIRE SYSTEMS
The flying control system, like any system, has an input and an output. In fact
it can have several inputs. The pilot is one of then - and normally the main one
- and another is the auto pilot. The output of the system is the movement of
the control surface - and hence the movement of the aircraft.
For the majority of aircraft the input is transmitted to the control surface via a
mechanical linkage - push/pull rods, cables, chains etc. It is a simple system
using technology that is easily understood. However it has its disadvantages.
* Heavy.
* Requires more maintenance.
* Complex - with many different moving parts.
* Non self testing.
* --Not
- so precise - play - backlash~tc. I
7 - -- ,
*
-
Difficult to interface-~th-Cith3r,el~ctronic
equipment, eg auto pilot.
* I Less responsive to actual aircrqt needs. I II
* : Less safe - a computerised system1can have builtjn safety re: stall,
windshear, overspeed, ahd overload.
1 -' ,
1 ' ,
' // 1
Operation - General
The aircraft will only do what the computer allows - what is safe and what the
aircraft is configured to do, eg the aircraft cannot be stalled.
Signal Transmission
In a Fly-by-Wire system the signal may be analogue or, more usually, digital
electric/electronic. In a Fly-by-Light system the signal is visible or laser light
pulses digitised down wires which are made of high purity silica glass.
Safety
Most systems will have a level of integrity to make then a t least as safe, or
safer, t h a n a mechanical system. This will usually include more than one
power supply; more than one signal transmission path; more than one
computer per signal path; and more than one software supplier for each of the
duplicatedl triplicated computers.
Should all else fail many systems have a t least some mechanical back-up. For
example, the A 3 2 0 and A 3 3 0 have a mechanical linkage from the rudder pedals
to t h e rudder PFCUs and the trimrnable tailplane has a direct mechanical
cennPFfG6
- tn the flightdeck trim wEee1.- ,
-
-
I
EXAMPLE - THE AIRBUS ~ 3 3 0
I
,
The first two-control the aircraft-in-pitch, roll and yaw and-the SFCCs control
the slats and flaps. All surfaces are actuated by electro-hydraulic PFCUs.
Flight deck indication and maintenance functions use Flight Control Data
Concentrators (FCDCs).
This replaces the conventional control column with a left hand side-stick for
the pilot and a right-hand one for the co-pilot fitted to the left and right control
consoles.
The side stick connects direct to a sealed unit under the console. Connections
to and from the sealed unit are all electrical.
Within the sealed unit are torque tubes, levers, dampers (1 roll 1 pitch), spring
feel units (for roll and pitch), control stops and transducers (four for each
control axis).
The stick is held in the neutral position by the spring feel units.
Pitch Control
Signalled from the flight deck by the-use-of a side-stick tormove the two
elevators. There is also a TrimmableHorizontal Stabiliser (?;HS)-moved by the
centre console handwheel. I ,
1
I
The position of the control surfaces is shown on the System Display (SD)via
the Flight Control Data Concentrator (FCDC).
Each elevator is moved by a servo in the active mode whilst the other is in
damping mode. In normal configuration the active servo is the inboard one.
When large deflections are called for both servos become active.
With the loss of all electrical signals the servos are centred hydraulically.
Pitch trim is provided by adjustment of the THS. The pitch trim is signalled
automatically in normal operating mode, ie the electrical mode. In emergency
mechanical mode operation of the tailplane is achieved using either of the two
interconnecting handwheels on the centre console. Mechanical control will
override the electrical control.
SIDE
STICKS
Roll Control
The ailerons and spoilers are signalled by the lateral movement of the flight
deck side stick.
At high speed (Vc higher than 190kts in CLEAN CONF), the outboard ailerons
are sewoed to zero. In A / P mode and in certain failure cases the outboard
ailerons are used u p to 300kts.
When the RAT is extended, the outboard ailerons are not used, all the servo
controls being switched to the damping mode in order to minimise the
hydraulic consumption.
r-----i
FLIGHT
1
11,2,3 CONTROL
SECONDARY
Im I COMPUTER
I I
I I
I I
L-----J
C
r-----i
LGClU 1,2, w
L----- FCSC
FLIGHT
CONTROL P 1,2,3= FCPC 1,2,3
PRIMARY S 1,2 = FCSC 1,2
COMPUTER 0, G, Y = BLUE. GREEN,
YELLOW HYD
SYSTEMS
+ARROWS INDICATE
ACTUATION
RECONFIGURATION
PRIORITIES
The position of the control surfaces is shown on the SD via the FCDC.
Each aileron is actuated by one servo in the active mode while the other is in
damping mode. In normal configuration the outer servo is in the active mode.
The damping mode of the other servo helps reduce flutter.
Should electrical failure occur the active servo will revert to damping mode ar '
,
Yaw Control
The rudher control associated with the aihrons and spoilers permits automatic
rolljyaw coordination during tGrns and the damping of Dutch Roll. It is also
used for airci-aft guidance on the'ground.
-- --- -
In case of total loss of the electrical controls, the rudder also permits yaw
control of the aircraft by direct mechanical linkage.
Interface with Nosewheel Steering System. The pedal transducer units send
position d a t a to the BrAnglSteering Control Unit (BSCU) through the FCPCs
for the nosewheel steering system.
CENTRING
MECHANISM
- - 7 - -
.
- - L c, lrllr rn.,san,
8 .mu,,,--z,. ,..WL
I
I SECONDARY\
I COMPUTER
b
I
FLIGHT CONTROL
I PRIMARY COMPUTER
, i
I
/ / --
ROFL SSTU c i - -
., ,\
1I
RATE I
GYRO--+ FCSC 1,2 '
I s1
1,2,3 1
r---I-
FMGEC 1 , ~ -
1 --
L---,,
L -- -
J- r
--
CONTROL MECHANISM
1 F::r?l
r----- I SECONDARY
SFCC 1.2 m
L----, J LFCSC COHPUTER BACK-UP
SFCC -+ YAW DAMPER
B UNIT
r------I
1
c LGClU -+ >(
I ADlRU I
u TRIM
ACTUATOR THANMM
ART FEEL
--tALERONS -7
L--,--J
r-----l
LGCIU 1,2 * 52 1 s U P ART FEEL
SPRING ROD
L----- J
U P SOLENOID
r----1
-BSCU 1.2 FMGEC
L---- J
TRANSDUCER
.c
MECHANICAL CONTROL
RECONFIGURATION
YELLOW HYD PRIORITIES
SYSTEMS
FLIGHT CONTROL
COMPUTERS
-
E -
SIDE STICKS
PEDALS c ,RUDDER
L
E .
c
.! OUTBOARD
AILERONS (2)
RUDDER TRlM CONTROL SWITCH ----C TRlM IND T
R INBOARD
SPEEDBRAKE CONTROL LRlER- 0 7 AILERONS (2)
THROTTLE CONTRIOL LEVER PRIMARY
COMPUTERS H
Y * 2 SPOILERS 6
FAULTIOFF PUSH BUTTONS
- --- - -
" --a
D
--
- - A 2 S?C!IE!?S 5
-
i - -
2 VERTICAL ACCELEROMETERS-
' RATE GYRO UNIT I 2 SPOILERS 4
HYD PRESSURE SENSORS c
TACHOMETERS
2 LATERAL ACCELEROMETERS
FMGEC
- 2 SPOILERS 3
SF,CC y
7
HSMU
ADlRU
2 ELEVATORS
RA -/,' b
i-- '
LGClU +
ECU
-
P., - --
--
SERVO CTL
ELECTIHYD
TRlM
HANDWHEEL
-
MECHANICAL CONTROL -
ACTUATOR
EIVMU
FLT CON DATA
CONCENTRATOR
(2)
WARNINGS-*
MAINTENANCE
FCMC
-
NVC
CMC
blank
- 46 -
rnoodull lA_990
Electrical control: Hydraulic
Hydraul~cactuation:
actuation'
'A~lerons
'Ailerons 'All surfaces
'Roll spoilers
spollers
'Rudder trim
trlm Mechanical control:
control.
'Elevators ' Rudder
'THS THS
'Slats &flaps
" Speedbrakeslground
spoilers
spo~lers
'Rudder
SLATS
HORIZONTAL
STABlLlSER
7-- - - - - -
I
- -1
! 1' I--
I Fig. 36 A330 FLIGHT ~ ~ N T R OSURFACES
L \
I /
' /'
THE BOEING 777 FBW SYSTEM
I I
I ,\
\ 1
The Boeing 777, like the A330, lhCs a highli\,integrated flyink control system.
Unlike the A330 it uses convenkional fligGt-deck controls. s\&alling between
comput<rs is via ARINC 629 data bus with ~ a l o g u signale
e corning from flight
deck transducers and analogue ~ i ~ n a l s ~to~ the
o i hydraulically
n~ powered PCUs.
-,
1
>
L-- -I I
Primary flying control surfaces on each wing are one aileron (outboard),one
flaperon (inboard) and 7 spoilers (one spoiler being mechanically selected all
others are FBW). The other primary flying control surfaces are the rudder, the
elevator (2) and the stabiliser.
In normal mode the primary flight computers compute control surface position
from the following inputs:
A Pilot.
* Autopilot.
JC Windspeed and direction.
* Phase of flight.
* Attitude.
A Altitude, etc.
Secondary mode is initiated if sensory information is lost. This means that the
Air Data Unit, IRS and Secondary Heading Reference units have failed. The
autopilot will drop out. The Primary Flight Computer (PCU) will still operate
using pilot inputs but some of the protection devices such a s bank angle
protection are lost.
In Direct Mode some of the computers are not used and the Actuator Control
Electronics unit (ACE) controls the control surfaces direct (still using FBW). The
pilot can select Direct Mode or it can be selected automatically under some
failure conditions.
The flight deck controls consists of a conventional control column for control of
the elevators with a hand wheel for control of the ailerons, flaperons and roll
control spoilers. The rudder bar controls the rudder. These controls are provided
with artificial feel and back-drive motors to move them in the correct sense
when the system is in A / P mode. An aileron trim actuator i s fitted to the aileron
system.
There is a-direct control cable run fro-m the pilot's hand wheel to the PCU of
spoilers 4 (left wing) and 11 (right wing) and there is direct kable control of the
stabiliser trim from the flight deck pitch trim lever to the stabiliser trim module.
I
- 48 -
rnoodull l A-992
The ARINC 629 d a t a b u s is a twisted pair of wires transmitting data in both
directions to all cornputers/LRUs (Line Replaceable Units). Each cornputer/LRU
is connected to the b u s by untwisting the twisted pair locally and clamping on
a n Inductive Couple Unit (which does not cut the insulation of the bus). In
operation each computer listens to the bus and waits for a quiet period before it
transmits. It t h e n waits its turn until all the other computers/LRUs have
transmitted before transmitting again (the system of listening and transmitting
is called 'protocol').
-- -
WHEEL BACKDRIVE
-
ACTUATOR RC ---
WHEEL BACKD
-
ACTUATOR L SPOILERS 4 & 11
ORCE LIMITER
FEEUCENTRING
ASSEMBLY
Having recognised that the information on the bus a t that instant is to be 'read',
it will take it in, put it in temporary store (RAM) and act on it according to its
pre-programmed instructions.
The flight control system uses 3 buses (left, centre and right).
Flight deck control movement is converted into an electrical analogue signal by
transducers (XDCRs)fitted to the flying control system under the flight deck
floor. This signal is then sent to the ACE unit where it is converted into a digital
signal.
The pilot's controls are connected via the ACE unit to the PCU. Other units s u c h
a s the PFC and the ADIRU (Air Data Inertial Reference Unit) are connected into
the system by the ARINC 629 bus and send data to the ACE unit. The drawing
below shows a block schematic for the ailerons but the rudder and elevators are
similar i n principle.
HAFDC (3)
The hand-wheels are connected electronically to the ailerons and flaperons and
mechanically by cable to spoilers 4 and 11.
The flight deck control is connected to position and force transducers which
signals the pilot's intention by a n analogue signal to the ACE. This is in two-
way communication via the data bus with the PFC. After digitising and
comparing/summing with other signals an analogue command signal is sent t o
the PCU to move the ailerons in the desired direction. Positional feedback is s e n t
to the ACE which controls the range and speed of movement of the PCU - and
hence the control surface.
The flight deck controls have artificial feel to simulate air loads and trimming is
achieved by biasing the system neutral by a trim unit actuator.
Should one side jam then the other side can be operated independently by
overcoming the force limiters. Should the spoiler control cables become jammed
then system operation is assured by the shear-out action of the cable pulley.
Autopilot
When A/P is engaged all three autopilot computers are selected and input data
into the system. The back-drive actuator will move the pilot's controls in
response to A / P servo commands. Whenever the A/P is engaged the back-drive
actuators are active.
When autopilot is selected the PCU is controlled by the ACE, PFC and Autopilot
Flight Director Computer (AFDC)via the bus. The AFDC will also send an
analogue signal to the back-drive actuator to move the flight deck controls to
correspond to control surface?novement.,Thus the system-simulates closely the
chara~te6sticsof a conventional mechanic$ flying control system.,
' I \
I I
~
I I
I I
1 I
Fault Finding I , 1 I
' \
/ I ! /
I
/
Beside3 &heckingthe AMM and' ~1hCthkre'i~ an onboard fadlt ' c 0 ~ 3 t e rwhich is
\
accesskd?via the Maintenance dcc!ess ~ e r ~ i h(MAT)
a l on th&flight deck.
I 1 i I
The MAT comprises: I 1
- .--- /
* A display screen. - --
-
j
: Keyboard.
* Trackball - similar to a mouse - controls the cursor.
A Selection switch.
A Portable MAT (PMAT)can be used which is plugged into the system a t various
points on the aircraft.
Some tests can be carried out using the MAT. These can cause the control
surfaces to move a s well as the flight deck controls, so it is important to ensure
that they are free to move with no obstructions and warning notices displayed.
FLY-BY-LIGHT
This system is similar to the fly-by-wire system except that the digital signals
are transmitted down a fibre optic cable instead of an electronic signal down a
data b u s or electrical cable.
The pilot's input is sensed by an analogue transducer near the flight deck. This
analogue signal is then converted to a digtal electronic signal and worked on ' - 7
CI - - ~ n m n l l-.
nnm-1 ~ + a n
b"IIIpULUL V*
f ~
"VLaLr-LVA --- is ~ewerteT1
r ~ ~ip-d
The tn digital light pulses for
transmission down a fibre optic cable. At,the end of the transmission line the
signal i s converted back to an electronic digital signal then converted back to an
analogue signal to operate a solenoid in the powered flying control unit (PFCU).
I
include: ,
J;
Not ai'fected by electric or magnetic fields.
j;
~ e s prone
s to data corruption due to lightning Strikes.
JE No risk of cross-talk.
* Lighter.
* Smaller.
~r Faster transmission rates.
* More reliable.
The electronic digital data is converted into light pulses by a light emitting dioac
and the pulses are carried in a covered glass fibre to the receiver. The receiver is
a light sensitive photo-transistor which converts each light pulse into a n electric
signal.
\
OPTIC FIBRE OF LOW LOSS HIGH
REFRACTIVE INDEX SILICA GLASS RECEIVER
TRANSMITTER
OUTER JACKET
STRENGTH \A
BUFFER JACKET
SILICONE COATING
FIBRE
Several strands are put together to make up a fibre optic cable. Dummy filler
strands might be included to keep the bundle cylindrical. The cable is protected
and sirengthened by additionral materid-s,uch a s tape a n d m i d yam.
-I \ --
--\ ,
Each fibie optic core element is!very sma)l- about 0.0055 in (0.14mm) in
diameter, with the fibre optic s{rand being about 0.035 in (0.89mm) in diameter.
The fibre optic cable is about 0.2 in (5.1,mrn) in diameter. 1
, , 1
DS
SEPARATOR TAPE
Fibre optic cables are easily damaged, so should be handled with care. Damage
can be caused by:
* Twisting and pulling - as when pulling through a loom/bulkhead.
A
Compression - as when standing on it.
* Routing through too tight a bend (maximum radius 1% in).
Note. If damaged the cable may not show any external signs, so a visual
inspection must be accompanied by a functional test/BIT.
Fibre Optic Connectors
There are several different types of connectors. The ends of t h e connectors are
fitted with a small protective piece of glass, which should not be touched and
only cleaned using the approved materials a s laid down in the AMM. Always fit
protective caps when connectors are disconnected.
Some connectors are designed to be used in locations that will not warrant their
frequent disconnection. These are sometimes called a Butt Type a n d have good
light transmission qualities. Those that require more frequent disconnection a r e
less efficient a t light transmission.
INTERNAL
FIBRE
\ TERMINUS
PROTECTIVE I
GLASS COVERS 1
---- ,
Fig. 43 DETAIL OJKSINGLE FIBRE OPTIC! BALL
LENS TYPE CONNECTION I
1
I
1
/
I
STRENGTH MEMBER
CONNECTION
~
\
PROTECTIVE
WINDOWS NUT
WARNING
MACH TRIM
A s the aircraft speed increases towards MCRITSO the Mach effects start to
i n f l u e m the aircraft's stabilityand-performance. These effects vary widely
between &craft. On some aircraft the effects can be pronounced and start a s
low as M0.7, on others the effects can be'mild and start a t Lgund M0.9.
However, one general symptom that affects most high subsonic aircraft is the
rearward movement of the centye jof (C of P) of the wing. This effect
(tuck-under) increases as the aircraft-fio~ts through the tranponiq s&ed range.
I I
--
---
\ I
_/,'
' \'
An autopilot system would obviously take care of this kind of instability so when
it is operative the Mach trim system is clutched out, but the autopilot may not
always be engaged.
The pilot c& carry out manual trim if necessary without upsetting the operation
of the system.
The Mach trim input is via the Mach Transducer and the Summing Mechanism.
The tailplane will continue to move until the feedback link 'catches up' with t h e
position of the Summing Gears (also negative feedback) when the selector rod
into the servo valve is returned to neutral.
The two feedback systems work together so that the differences in their timing is
not noticeable.
Examples
Boeing 737 Mach trim is connected to the elevators through the autopilot
system and on the Boeing 747 it is connected to the tailplane actuator.
-
I
I I
PlTOT STATIC
SERVO VALVE
RETURN
/
SUMMING
MECHANISM . ELECT
SUPPLY
blank
STALL WARNINGIANGLE OF ATTACK INDICATION
These systems are fitted to give warning of an impending stall; to provide for
stick shaker/stick push warnings/systems; to initiate engine auto-ignition; to
provide indications on the flight deck and data to the DADC etc.
Stick Shaker
The stall-warning device may connect the stick shakerlstick push directly via a
micro switch to a dc supply. The angle of attack transducers send angle of
attack data to a computer and signals to the stick shaker/stick push will come
from the computer when stalling angle is approached. The computer will also get
data on the configuration of the aircraft, eg flap and slat position, which will
affect the stalling angle.
-
1llL3
- 1
~
--
1
~ ~ +
1
33
U\U-y
I 2 ~
n 1
~ ~
1
--~
--
bAbbLLLL
-
t
lLIVLVL
t
uCLUbIIbU LV
LL L L ~
n>-trnt
bVIILL
-~~n+nrn
\JY oLbIIL
\ '7
close to the control column (actually o n t h e column on some arcraft). When
switched on it rotates an out-oflbplance whkel, which causes the control column
to shake (also operates an aural karning)'- barning the pildt of an iApending
1 , '
stall. I -'<\ , /
--
I \ /
I
' \ / I -
Stick &kh , ll I
I I I
I ' I
Pneumatic supply pressure can come from a tapping from the jet e n g n e -
typically about 40psi.
Fitted to some smaller aircraft and consists of a slot cut in the leading edge of
the wing a n d connected by a plenum chamber and small diameter pipe to an air
operated sound reed situated in the cockpit.
A s the angle of attack increases so the stagnation point gets lower o n the leading
edge, this causes a negative pressure to be felt in the plenum chamber and pipe
line, which causes air to be drawn in through the sound reed. This causes the
reed to give out a warning sound.
.. - - - -- --
Fitted close to the stagnation point on the leading edge of the wing on some
smaller aircraft so that as the angle of attack is increased the upward airflow of
the air at the leading edge will cause the vane to move u p (normal angles of
attack will keep it pushed down). As it does so a microswitch is operated
causing a warning larnp/aural warning to come on in the cockpit.
Consists of a moveable probe within the airflow, with two slots in it, connected
to an internal paddle. The two slots in the probe are open to dynamic pressure
(airflowpressure), which are connected to two chambers separated by the
moveable paddle. The paddle is connected to the probe so that a s it moves, so
does the probe.
LEADING EDGE VANE
ELECTRICAL
CONNECTION
TRANSDUCER /
TRANSDUCER
OPERATING
VANE
TRANSDUCER - k c
MOUNTING
P W E
!I I 1 I
I
A s the angle of,attack increases so the dynamic airflow moves towards the
I
bottom slot, increasing the dynamic pressure in this slot and under the paddle.
Thisrcaui&i it to move u p androtates
--
the probe to move the dots down. This
---
action will reduce the dynamic pressure in the bottom ~lo;-andincrease it in the
top slot and cause the slots to take up a position where the pressures are equal
in both. Thus the paddle will take up a position that is related to the angle of
attack of the aircraft.
Note. Angle of attack is often called Alpha angle in pilot's, training manuals etc.
S LO
CHAMBER
POTENTIOMETER
AIRFLOW
This is a trailing wedge type aerofoil that 'trails' in the air flowing passed the
aircraft and therefore is always a t the same angle a s the airflow. Like the
PntGlngAnglr of Attack Probe it is mounted on the side o f t h e fuselage and nA,
be fitted to both port and st&6omd~idesof the aircraft to allow for errors due to
side slip etc. I ~
I
-
- -
TRANSDUCER
blank
Figure 50 shows the a circuit for the BAe 146. Note the following
inputs/outputs:
* Weight on wheels (squat).
* Flap position.
* Test.
* Power supplies.
* Airspeed.
* Fail.
DE-ICE
SENSOR
FLAP INPUT
I
AC POWER
DC POWER 1 I
RATE INHIBIT
- - , AIRSPEED TRANSDUCER I
ONE CHANNEL SHOWN . _ -1
I TWO CHANNELS PER SYSTEM [ --
I I
'\ '
AIRSPEED TRANSDUCER
AC POWER
DC POWER
- --
AOA-AFFLOW SENSOR VANE i
VANE EXCITATION
WARN
FAIL
1 T E S T
FLAP INPUT
Page
Draining
Engine fuel feed systems
Basic system I
Bopst pumps
Fukl lines
Water scavenging I 1
I
ManuZl methods
Mechanical instruments
Electrical instrument systems 42
Electrical/ electronic systems 42
The capacitive system 42
An electronic system 49
An ultrasonic system 51
Exercises 54
Answers to self assessment questions 54
AIRCRAFT FUEL SYSTEMS
Before we start it might be a good idea to define what is meant by 'an aircraft
fuel system'.
SAQ 1 Describe what constitutes an aircraft fuel system, where does it start
and at what point does it change to the engine fuel system?
A fuel system consists of various sub systems and these can be grouped as
follows:
Storage system. There needs to be some form of storing for the fuel prior to it
being used by the engines. It is stored in fuel tanks along the aircraft's
longitudinal C of G in the wings and centre fuselage. On some aircraft fuel is
also stored in the fm/ tail section of the aircraft (trim tanks). The capacity of
these tanks is small but the fuel is-also used as a trimming medium - the more
fuel that is pumped to the trim taflks-theheavier the tail of the aircraft
'
gets.
Useful for ordinary in-flight trimming as well as Mach trirnTihg.
I
I
Refuel/defuel/drain system. used for fuelling the aircraft a n d a t the same time
removing any entrapped air. Sometimes (generally for maintenance) the fuel
needs to be removed from the t h k s . - ~ v ~ n ~ a fatcomplete
er hefuel, there are
still pdddles of unusable fuel left in the tanks and if personpe? need,to enter
the tankl(forinspection purposc&s:etc),there heeds to be some means of
I
draining that fuel' away. I
1
Jettison system. For most large aircraft it isn't structurally possible to land an
aircraft at its maximum all up weight (on long distance flights aircraft will take-
off heavier than they are allowed to land).
During flight fuel is burned and the aircraft mass falls. If a serious malfunction
causes a return to base just after take-off the aircrew need to dump some of
the fuel overboard to reduce the aircraft mass). This is done using a fuel
jettison system.
It is worth noting that due to environmental and cost concerns, aircraft do not
jettison fuel often, they will usually opt for a n overweight landing - with special
checks on airframes, airframe systems and engines to be carried out by the
maintenance engineer afterwards.
Indication system. Both the flight-deck crew and engineers require information
about the quantity of fuel on board. A variety of systems are available to
include mechanical, electrical and electronic systems. Most aircraft also have
back-up systems.
STORAGE SYSTEMS
Fuel, for the conversion to heat energy and thence to kinetic energy in the jet
engine/piston engine, is stored in tanks normally within the aircraft. On some
(usually military) aircraft it may be stored in external tanks and may be
transferred to the aircraft in flight via an in-flight refuelling system. Tanks may
be either flexible, rigid or integral.
FLEXIBLE TANKS
Al-n
I UU" r ~ l l ~ 'r0 0l1 1 ' gr
b C U A U U ""LA %sg tnks'. They %re ms-rle nf fl-IPI r ~ s i s t a n polymer
t
materialsand are designed to fit snugly inside specially designed
compartments of the airframe. They do have several limitations and as such
are not seen much today, but you will still need an understanding of them, a s
they are still used.
I '
~
~ s u qplaced
l ~ within the wing structure, and due to the flexing of the wing the
tank is made slightly larger than the volume in which it is placed. This ensures
the Aningstructure, not the tank, takes the stress loads of the fuel and any in-
flight loads.
Bag tanks are constructed from thin rubberlsynthetic rubber material and
-
Flexelite. A red or black Flexsyn material which is synthetic based and similar
to Hycar. Also available in two thicknesses, the standard 0.045" (1.14mm) for
tanks with capacity greater than 100 imperial gallons (454.61),and lightweight
0.020" for tanks with capacity below 100 gallons.
Marlite. A blue coloured material of a two ply Nylon and Terylene fabric
impregnated with a fuel resistant barrier. This is the most common material a s
its properties include a working temperature range of +lOO°C to -60°C. Also,
due to the fact that no 'fuel-extractable' elements are used, these tanks always
retain their dimensional stability. This removes the need for stabilising
processes that are required in most synthetic based tank fabrication. Usually
only available in the one thickness, 0.020".
-2-
rnoodull l A-1008
All three of these materials will have a protective and supportive Iayer around
them. This is often made from a fabric impregnated with rubber. This makes
them more durable but great care is still needed when handling. A s they are
flexible they will require support in the wing structure, particularly when they
are empty. Figure 1 shows some examples of the most common supporting
methods. (a)The tank is supported within the tank bay by a length of cord.
(b)The tank has studs bonded to its external surface and these are pushed
into corresponding stud fitting holes in the tank bay.
EYE
FlTT
STUDS TAN
STR
TANK BAY
-
//
pF\
STRUCTURE
BUTTON
\
\ A- - - A
+
---- I
1. Ensure both the workspace where the tank is folded and the aircraft
cavity are clean and there are no sharp edges.
2. M a k e sure that all protruding rivets, fasteners, brackets etc, in the tank
cavity are protected with rubber tape.
5. Remove all personal lose objects from pockets etc before entering the
tank area (a standard precaution with all tank work).
- 3 -
rnoodull l A-1009
1. INSPECT TANK 2. FOLD TANK AS
FOR DAMAGE. PLACE STATED IN THE
ON A TABLE AMM. AVOID KINKS
PROTECTED WlTH OR TWISTS
THICK BLANKET OR
SIMILAR
1
Fig. 2 FLEXIBLE TANK - PREPARATION FOR FITTING
- -
RIGID -TANKS-
These do not have some of the problems associated with flexible tanks, b u t
they tend to be heavier.
Figure 3 shows an older rigid tank assembly. Tanks are usually constructed
from aluminium alloy and sealed during manufacture. Sometimes tanks are
fabricated from glass-reinforced plastic or even steel (rare). Larger tanks
normally have internal baffles to prevent fuel surge (movement from one part of
the t a n k to another during aircraft manoeuvres). They will have cut-outs to
allow for normal fuel movement within the tank.
Each t a n k is designed s u c h that it fits into a specific space within the airframe
with clearance to allow for attachments, pipe connections, removal, re-fitting
etc. As with flexible tanks they will have the appropriate connections for refuel,
defuel and fuel feed.
Each tank will have its own pumps and hence electrical connections. A s the
tank is metal it must be electrically bonded to the aircraft structure via a
bonding point.
Some rigid tanks (as well as some flexible tanks*) have an additional external
covering that is designed to swell when in contact with fuel. When wetted with
fuel it will swell and, with a small leak, seal the tank. This tends to make the
tank self-sealing, though it has had limited success.
ATTACHMENT
COVER PLATES
FOR INTERNAL
F17TINGS
INSPECTIOr
I PANEL
I
Fig. 3 RIGID FUEL TANK - FUSELAGE FITMENT
I
I ]
/
/
_,
i
Due to their weight penalty and poor space utilisation rigid tanks are not often
used on commercial transport aircraft.
'External' tanks a s fitted to military and some light civil aircraft, and are
essentially rigid tanks. There are also rigid tanks fitted inside a cradle and
loaded into freight bays etc, to increase an aircraft's range (rare).
The B747, for example, had this facility in the early days, but not many
operators used it so it has been subsequently removed.
INTEGRAL TANKS
Integral tanks are areas, usually within the wing structure, in which the actual
load bearing structure (usually front spar, rear spar and 2 ribs without
lightening holes) is sealed to fomn the tank.
The advantages of integral tanks are that they are easily maintained, are
cheaper and save weight. They can suffer from leaks, however, and these show
u p as stains/ seepage o n the underside of the wingslfuselage. In some cases
the leaks can be enough to wet the hangar floor.
The leaks are caused by the flexing of the wings during flight. This causes
minute movement between the skin/rivet interfaces and, even though the
interfaces and inside of the structure are sealed, leaks still occur.
Figure 4 shows a typical wing structure of a large aircraft showing two integral
tanks in the wings with an additional integral tank in the wing centre section.
Firstly all surfaces are carefully cleaned and joined together with a fuel
resistant-(Polysulphide based) sealant as an interfay. This IS a two-part mlx
that cures with chemical reaction, not with air. After the joint h a s been closed
(rivetedup),a fillet seal is applied, which, in addition to sealing, helps transfer
the structural loads from one &ember
I 1 to the next.
I
I
DOORS
Following on from this and before the fillet is fully dry, one or two, brush coats
are applied, again with the next layer being applied just as the previous one
goes tacky. Finally a protective barrier coat is applied; this dries quickly and
allows the manufacturing process to continue without contaminating the
slower curing sealant underneath. These sealants can take three to four weeks
to reach full strength. The same general process is used when-ever repairs are
carried on the structure which is part of an integral tank. Of course, always
consult the SRM.
-6-
rnoodull l A-1012
CLEAN SURFACES APPLY SEALANT RIVET UP REMOVE EXCESS
SEALANT
I I FILLET
A word of caution about fuel resistant sealants. They all contain harmful
substances i n their activators; Either manganese oxide orrstrontium chromate.
Both y e lethal a n d specific handling inst&ctions must bb-followed when using
these prdducts. I
~
j
I I 1
I 1 I
Integral tanks have a series of access panels often under the wing; these allow
access for rework or inspections. They require attention to seding. Also a t
various Gositions inside the tank there q e baffle plates a n d fuel dams designed
to redhck fuel surge - a n d to kegp the fuel nearer the boost p u h p inlets.
\
I I
l 1
The surge problem is more common on thin wing sections, anti as a solution,
the fuel may,be sent from the integral_-tank,to a collector t h k ' v i a a Fuel/No Air
i
The engines are fed from the collector tank so they continue to receive fuel. Not
a common system but one that is still in use on some aircraft.
The disadvantages of integral fuel tanks include the initial cost of fabrication,
difficulty in repairing a n d fuel seepage. They are not crash resistant in that any
structural failure will lead to significant fuel spillage.
Leak Assessment
Tanks should always be kept fuelled to a certain level, a s this helps prevent
leaks caused when the sealant (or tank bags themselves) dry out.
During ramp maintenance about the only task the engineer h a s to perform
with tanks is filling them up, and even that job is often contracted out to the
fuel supplier - for major operators anyway. However, sometimes tanks do leak
and the leak has to be assessed and the appropriate action taken.
Any external leakage on an aircraft fitted with rigid or flexible tanks may
indicate that fuel has already collected in the structure of the aircraft itself.
This requires immediate attention.
Integral tanks have 'allowable' leaks (see figure 6). The correct procedure for
leak assessment is stated in the AMM. In general, ensure the tank is full, clean
the area and make sure no external fuel is present. Allow a period of 15
minutes to pass, then carry out the assessment. Where these leaks are and
what you do about them depends on the AMM. Where there is a wet area or
stain the AMM may designate the area depending on the size of the stain/wet
area.
A s a guide, running leaks are not permitted anywhere. Areas around engine
hot sections and turbine containment areas are not allowed any leaks at all.
Other open areas, that have good ventilation, can have seeps or stains. If a leak
is outside the limits it needs repair, and this may be a temporary external
repair.
I ' I
up to 1.6'
0 1.5 to b"
0
0
- -
STAIN - - - -
SEEP
Besides repair, tank entry, on larger tanks, is also needed during scheduled
maintenance and structural inspections. Fuel is inflammable, toxic and a skin
irritant so precautions need to be taken before and during tank entry.
SAQ 3 What precautions should be carried out before entering a fuel tank?
Answer below.
3. Open all access panels and if possible vent the tank (provide a
supply of fresh circulating air) for a period of time.
4. Ensure the tank atmosphere is not explosive (ie all fumes are
removed) - there is equipment available that can indicate this
--- information by sampling the air. - -
I-
> --
\
\ - -
5. Ensure sufficient fre$h air is,available - if there is not then
breathing apparatus is required.
' I
I
Inspection lamps, torches and any other equipment taken into the
tank must be flameproof and spark proof.
On the top surface of the wing (or fuselage in some cases) there is a filler cap
and tank opening. After operating the quick release fastener and opening the
refuelling panel the refuelling cap is unscrewed from the tank. In figure 7 the
refuelling cap is fitted flush with the wing surface and lifting the tab on the c;,,
allows the cap to be removed (by twisting the tab or operating a lever).
The filler port may be connected to pipework delivering the fuel to all tanks or,
more often, directly into the individual tank. The cap is usually connected with
a lanyard to the structure to prevent loss and there is usually a bonding point.
I
-
To rebel, the fuel nozzle from the bowser is bonded with its bonding lead to t h e
tank and the nozzle placed inside the tank orifice. The nozzle lever is operated
to allow' fuel to flow into the tank. Care needs to be exercised as the tank starts
to get full, as it is a high delivery rate a n d the fuel will spray back out of the
tank when the tank becomes full. Towards the end of the filling operation flow
ratesshould be reduced and preparation made to shut-off the control handle
quickly.
Other potential pitfalls include the danger of walking on the top surfaces of
wings and the possibility of damage to the wing from, filler caps, fuelling hoses
peoples shoes etc. Also there is a risk of fuel imbalance between the tanks.
After refuelling the bonding lead should be disconnected a n d the cap closed.
Most small aircraft only have the one method of refuelling - gravity refuelling,
but some larger aircraft have both systems fitted. The B747, for example, has
the option of over-wing fuelling, but using this method would require u p to 8
hours to fill the aircraft.
Over-wing refuel points on large aircraft are rarely used. Some aircraft are not
fitted with them a t all, eg the B777.
FUELLING PORT
- - -
,
I \ \
1
I
-- -- / 1
Pressure Refuelling
I
I -- - . -- , /
1 -,
This i s a,system,of refuelling whete fuel uhder pressure [rnax &bout 50psi
(345kPa))is supplied from a bowser, tank&,)or refuelling p i p i n g vehicle. (It is
common 'at large !airports to have the fuel' pumped underground. A vehicle
connects irito the ground conndctian [gt~r'liftinga steel codef plate] and
pumps th6-fuzinto the aircraft); ThFbowserys(fuel tankek) fuel'hose is
connected to the refuelling point (figure 8). From this single point there is a
pipework system connected to all the tanks in the aircraft. The fuel is
controlled into each tank by energising solenoids in the refuel valves.
* Ability to fill any tank with any desired quantity of fuel using the
aircraft's on-board refuelling control system. Electrically or
computer controlled.
~r
Reduced risk of fuel contamination.
* Better access. Fuelling points are accessed from the ground.
* Reduced fire risk.
- 11 -
rnoodull lA-1017
AIRCRAFT
REFUELLING
EARTHING OR BONDING
STANDARD CROCODILE CLIP
HOSE
CONNECTOR
SEALING CAP
GROUNDING PIN
CONNECTOR
SEALING CAP
W $ m w , ~ ~ ~ ~ ~ ~ ~ ~
HOSE
i
oper4tion
I I I /
I I
Figure 9 shows a typical refuelling system for a large aircraft, consisting of the
pressure connectors and the refuelling panel. Figure 10 shows a typical
refuelling valve.
With power available, and the refuel panel door open, the indications on the
refuel panel will show (the system may go through a BITE check first).
The dust cap is removed from the refuelling point and from the hose connector.
The aircraft bonding clip is connected to the refuelling hose and the hose
connected to the aircraft fuelling point via the quick release bayonet type
connector.
- 12 -
rnoodull l A-I018
The action of connecting the hose to the aircraft opens both the valve on the
aircraft refuelling point and the fuelling hose.
With t h e bowser pumping, the pressure will open the non-return valve and fuel
will flow into the system that supplies all the tanks (sometimes called a fuelling
gallery)-
FUELLING
QUANTITY OVERFILL RESET
TEST BUTTON
PRESELECT UNITS SWITCH
FUELLING QUANTITY
REPEATER INDICATOR
L
- ' \ pp
I
w w1 llat /:m OIIR) I
/
I ;i I
I
, Fig. 9 REF~ELLING
- C,ONTROL PANEL '
L
r' -
This fuel goes to the inlet of the refuel valves (figure 10).It passes through the
upper removal check valve (or non return valve) and, because there is a
calibrated leak to the other side of the diaphragm the pressure is felt on both
sides.
The spring in the refuel valve body holds the valve shut. If a particular valve is
selected open by operating the switch on the refuel panel, the solenoid will
energise. This allows the fuel on one side of the diaphragm (side 1) to be ported
back into the tank through the lower removal check valve. This ports the fluid
faster t h a n the calibrated holes allows side 1 to fill so the fuel pressure moves
the diaphragm (to the right in the drawing), and the refuel poppet valve moves
to the open position.
Fuel now flows into the specific tank until such time as fuel pressure is
removed or the solenoid is de-energised.
Once there are some valves open, and this is indicated on the refuel panel with
(blue) lights coming on, the valve position switch is moved and the pressure
from the bowser can be increased. (It should be reduced prior to final shutting
off).
Note that on this aircraft the diaphragm assembly can be removed without
removing the valve body. The diaphragm assembly is the most likely part to fail
a n d so it is useful to be able to change this without de-fuelling the tank.
-
FUEL IN
POSITION
SWITCH
/
SOLENOID VALVE LOWER REMOVAL
-- - CHECK VALVE
-FUEL IN
'EN
SOLENOID
The gallery may have restrictors installed a t certain locations to allow all tanks
to be filled a t the same time. Care still needs to be exercised to ensure an
imbalance doesn't develop (more fuel on one side of the aircraft than the other
would up-set the aircraft's C of G laterally).
Sometimes additional refuel points are provided to increase the speed of the
fuelling operation - so more than one bowser can be used simultaneously.
Refuel valves can be mechanically operated but they are normally solenoid
operated, using the fuel pressure to actually operated them open. This type of
refuelling requires overfill protection to prevent tank rupture or fuel spillage.
Also, with some aircraft care h a s to be taken when refuelling /defuelling so a s
not to p u t the longitudinal C of G outside the range between the main gear and
the nose gear.
The aircraft's C of G, for a nose wheeled aircraft, is just forward of the main
gear a n d with some aircraft with highly swept wings it might be possible to fuel
some t a n k s i n the wings such t h a t the C of G is moved aft passed the main
gear - this would cause the aircraft to tip back on its tail.
For tailed wheeled aircraft the C of G is behind the main gear and the tanks are
so situated so that it is not normally possible to overbalance the aircraft
longitudinally.
Defuelling
Figure 11 shows a typical defuelling system. With the bowser connected, the
non-return valves are de-seated-and the defuel handle is turn-ned. On newer
.
aircraft this may b e a swiich sricciiorl on iile rciuci par1el.-tms-connecis
1 m-
d
iiie
engine feed manifold (in the drawing) to the.refue1 points. T h e engine fuel feed
boost pumps are used to provide fuel to the engine feed manifold and through
the defuel valve to the bowser. i 1
- /
I
I
I -- \ . -\ I
I
- - '
JETTISON PUMPS
VALVES
JETTISON NOZZLE
VALVES
Fig. 11 DEFUEL SYSTEM
Once the bowser has positive flow the pumps on the bowser can be selected to
suck. Again, consideration h a s to be given as to where fuel is being taken from
to prevent imbalances developing.
SAQ 5 How can a combination of the refuel and defuel systems be used to
transfer fuel within the aircraft for maintenance?
- 15 -
rnoodull l A-1021
Refuelling/Defuelling Precautions
Fuel is highly combustible and fuel flow will cause a build up of static
electricity - which could cause a spark if the correct bonding has not been
carried out.
The following precautions should be observed (also check the book in this
series EASA Module 7 entitled Safety):
* Ensure the correct grade of fuel is used (AMM). See the books in
this series EASA module 15 for jet fuels and 16 for gasoline and
Diesel fuels). Check the bowser driver's log book to ensure that the
required dip checks (quality control checks) have been carried out
on that particular batch of fuel. This will also indicate the specific
gravity of the fuel.
The bowser must also be bonded to earth and this is often done
through the tyres or a bonding chainllead hanging underneath.
Draining
Prior to entering a tank for any reason the tank will need to be defueled and
drained. For most larger fuel tanks the only way fuel can be removed from the
tank during a defuel operation is via the boost pump, the inlet of which is
normally not located completely at the bottom of the tank. This will mean that
some fuel (typically 20 gallons - 901 for a large tank) is left in the bottom after
defuelling. This has to be removed by draining.
Light aircraft are often without boost pumps in the tanks and they have to be
defueled and drained completely from the drain ports.
Figure 12c$hows a typical drain Po?. are located at the bottom of the fuel
tank. For fuel sampling the primary poppet is pushed up, this de-seats the
valve and allows the fuel from the bottomofthe tank to drain \into a container.
During the above refuellingldraining operation the primary poppet vhve is
removed, this allows the second~arypppetto seat and prev&ntsspillage. A tool
is insetted to allow the secondary poppet t o de-seat and the fuel-to flow - into a
contairler.
,
Ii \
'\
I I
1
LOWER
WING SKIN
PRIMARY
POPPET
Venting
As fuel is pumped into (or out of) the tanks (refuelling, defuelling, engine use)
air has to be allowed in and out. Failure to do so could cause the tank to
rupture during refuelling operations or a vacuum to occur when the engines
are running and thus starve them of fuel.
When allowing venting careful consideration has to be given a s a highly
explosive fuel/air mix is being moved from the tank to the outside atmosphere.
Also when allowing air into the tanks contamination may enter via the venting
system.
For small aircraft the vent can be a small pipe connected to the top of the tank
which is open to atmosphere. A ball valve is fitted to prevent fuel leakage in the
event of inverted flight.
Figure 13 shows a typical venting system for a large aircraft - the purposes of
which are to:
* Balance the air pressure within the fuel tanks with ambient air.
* Allow for thermal expansion of the fuel/fuel air mixture in the tanks.
* Protect the tanks from excessive internal pressures.
B &X
. fi *~~ RESET HANDLE FLOAT ACTUATED
DRAIN VALVE
SURGE TANK
ACCESS DOOR
FLAME
ARRESTED
CHECK VALVE
VENT SCOOP
OUTBOARD SURGE
TANK ACCESS DOOR
This system uses the top hat stringer sections of the wing to transfer air to the
surge tanks. Here there are two valves, one inward and one outward with a
flame arrester attached.
- 18 -
rnoodull l A-1024
During fuelling fuel enters through the refuel valves to displace the air. Holes
are provided in the top hat stringer sections (part of the wing structure). These
sections are sealed in the same way as the integral tank structure. The air is
able to pass along the stringer section and out to the surge tank. The surge
tank has a n outlet that is protected by a stack pipe. The volatile air/fuel
mixture from the surge tank is forced overboard via a flame arrester and air
outlet.
TANK MOUNTING
- --
- -
ELECTRICAL I
SOCKET
MOUNTING
FLANGE /
BOTTOM REED
TUBE ASSEMBLY
- 19 -
rnoodull I A-1 025
A s the fuel in the tank continues to rise it needs to be stopped from entering
the top h a t section via the same hole that the air is going out through. This i s
done using a float valve (see figure 14).Air is allowed to pass through the open
valve b u t as the fuel rises it lifts the float and closes the outlet.
Overfill Protection
One way is to use a float switch (figure 15).As the level of fuel rises to the level
of the float switch, the float rises, the magnet moves tolaway from the reed
switch a n d it closes/opens and an electrical signal is sent to the refuel valve,
de-energising the solenoid and closing the valve.
Note t h a t the float switch shown in figure 15 has a lower and higher reed
- - --- L - - - - - 1
1
.+ rlt: l u ~ e ul r i c ; rlldy
s w i i c ~ lmi L- :---l:--L- LL-C
UC; U ~ C U LU L ~ ~ U ~ L ~
C L
L LC~ LLIE
L L tzilk is getti7i~k!! S G
reducing the supply prior to final shut-off.
I
Some (lkrge) aircraft employ both systems. The first line of defence is the VTO
systefn. Should that fail fuel is allowed to travel u p the vent lines into the surge
tankYA-float switch is fitted here and after a certain amount of fuel h a s flowed
in, the switch will operate break all electrical power to the refuelling system
thus shutting the refuel valves.
The fuel in the surge tank should not spill out, as a stack pipe protects the
outlet.
Whatever type of tank is fitted the principle for delivery of fuel to the engine(s)
is the same. Figure 16 shows a system for a light aircraft where the fuel feed i s
by gravity.
The tanks are higher than the engine and the aircraft is designed for moderate
manoeuvres only so the fuel can be gravity feed from the tanks to the engine.
The tank selector valve is used to allow the fuel to be taken from either, or both
the tanks. This allows the pilot to control the fuel and balance the aircraft
(laterally).
A collector tank is provided below engine level, or a collector compartment is
provided within the existing tanks to allow the aircraft to fly inverted. Under
normal operation t h e collector tank/collector compartment h a s gravity fuel
feed.
TANK SELECTOR
During inverted flight a float valvd clos;~ thk inlet and fuel is &d to the engine
from the collector tank/collector dompartment by gravity. ~ h e c a ~ a c i t either
~~of
system is limited and relies on the pilot riihting the aircraftbefore tdo long.
I
I - - , I I
O n low winged aircraft or aircraft w h a q the tanks are lower t h a n the engine/s
or where there is a long pipe run fom the, tanks to the engibes-gravib cannot
be reliedon to move t h e fuel. The fuel neeas to be pumped.
I
1
/ I
The engine fuql pump does provide some ,suction from the t h k , b u t a positive
pressure is required to keep the fuel-flow rate a t an adequate level and to
preventcavitation* i n fuel lines anckcomponents. So a pump is i'nstalled in the
line from the tanks to the engine.
SAQ 6 If the pump i n the system described above were to fail, will fuel get to
the engine and what sort of redundancy could be build into the
system?
Figure 17 shows a fuel tank system for a twin engned aircraft with low wings
with some dihedral.
In figure 17 the outer tanks (1 and 4) will gravity feed to the inner tanks (2 and
3),but on some aircraft a pump system is provided. Tanks 2 and 3 are pump
fed to the engines. The fuel supply can be controlled by the pilot by the u s e of
t h e various shut-off valves and non-return valves will be provided to prevent
fuel flow in the reverse direction.
- 21 -
rnoodull l A-1027
Re-fuelling is by gravity feed and de-fuelling is by the use of the tank drains.
Figures'l8,
-
19 and 20 shows a typical boost pump and its control circuitry.
.-
-- - A
w h e n the pump is selected O N the motor turns the helical impeller a t high
speed (up to about 10,000rpm). Fuel enters the pump through the inlet and is
moved through the impeller and the centrifugal impeller to the outlet.
The fuel inside the pump is also leaked' internally to provide cooling and
lubrication - though is kept separate from the electric workings.
With reference to figure 19 note the 30 115v 400Hz supply to power the pump
which is controlled by a 28v dc relay. Note the similarity of the pump windings
to the windings of a 30 generator.
- 22 -
rnoodull l A-1028
Boost pumps will normally be fitted on the front and rear spars of integral
tanks. Sometimes they are housed in dry bays internally on the wing surface.
Bag and rigid type tanks require additional supports for the boost pump
fittings.
ELECTRIC MOTOR
FUELIN
FUELTAM BASE
FUEL TO
ENGINE IMPELLER
I
1
I 1
I
; I
Fig! ~-
S --B O O ~PUMP
.- T I
I --
1
\
I
Ia I
I
I
I
I
NO 2 115V AC ' I
BUS /
-
-
-- - -
-- - ---
NO I MAIN AFT I
I
BOOST PUMP I
NO 1 MAlN AFT
BOOST PUMP
-
-
NO I MAlN AFT
0 BOOST PUMP
NO 2 28V DC BUS
NO 1 AFT BOOST NO 1 MAIN AFT RELAY
PUMP CONTROL BOOST PUMP SWITCH
Redundancy is built in (EASA23 for small aircraft and EASA25 for large
aircraft). Normally this is provided by having two boost pumps per tank, each
on its own being capable of delivering sufficient fuel to the engines to maintain
normal operation. Also the bypass mechanism is available should both pumps
fail. Additionally fuel can be used from another tank.
PUMP
PRESSURE
LOW PRESSURE
WARNING LIGHT
TO MASTER
BOOST PUMP TEST
PRESSURE SWITCH
0 U
-- 4
TOMASTER
DIM
Crossrfeed System
With &l',systems where there is more than one tank and more than one engine
there is a s c r i e s of pipes connecting-all the boost pumps a n d engines together.
This is called the cross-feed manifold, or sometimes referred to as the 'forward
gallery' or 'gallery'.
Fuel from the boost pumps is pumped out of the tanks and into the cross-feer'
manifold. It is controlled by a series of valves. To move fuel down to the engine
the LP valve or LP cock (sometimes called the spar valve) h a s to be open. This
valve is the last part of the airframe system. From here on the fuel system is
considered to be part of the engine.
To move fuel to another engine via the cross-feed manifold, one of the cross-
feed valves is opened.
Valves
- 24 -
moodull 1A-1030
* Allow unhindered fuel flow in the 'open' position.
* Provide pressure relief, should the pressure in the LP fuel pipe-work
become excessive.
* Indication of valve position, both remotely to the flight deck and
physically on the valve itself. (In the case of some light aircraft the fuel
control valve is fitted directly to the control knob, which means fuel lines
close to, or even in the cockpit. Not allowed in large CAT [Civil Air
Transport] aircraft).
Most valves are essentially the same; it is the actuation method that is
different. Figure 2 1 shows a typical remotely actuated electrically operated
valve. Note the valve body, this is similar on most valves a n d will be either a
butterfly style valve or a 'donut7type of valve. Both have internal thermal relief,
to provide over-pressure relief should (due to thermal expansion) the pipes
become over-pressurised. This fuel is ported back into a tank.
-
I
ADAPTER DETAILS
VALVE BODY
INDICATIONS
The valve works by a shaft turning in the valve body causing the butterfly to
open or close. How that shaft is turned varies from aircraft to aircraft. Common
on large aircraft is the one shown; the valve body is buried inside the tank, and
it h a s a n operating link connecting the valve body to a mounting plate. The
actuator is connected onto the mount plate via splined couplings and four
location screws. (Note the bonding lead).
- 25 -
rnoodull lA-1031
Indication of valve position is provided in flight-deck.
Figure 22 shows the indication circuitry for a jettison valve which is similar to
the one above - with the actuators being identical. It is powered by 28v dc.
Moving the switch to open allows the supply to the actuator which starts to run
a n d to the indicator via the closed contacts in the motor a n d will illuminate the
lamp.
The motor runs and the valve shaft and butterfly operate. When it reaches the
open position the contacts inside the motor are moved mechanically. This
causes the supply to be removed from the open coil of the motor and from the
indicator. The motor stops and the indicator goes out.
TO RIGHT CENTRE
JETTISON VALVE I RIGHT NOZZLE
VALVE SWITCH
B I
VALVE
CLOSE
W TO MASTER TEST
I I
RIGHT NOZZLE VALVE
INDICATOR LIGHT
Manual operated valves (used on small aircraft) use a small diameter [about
1/8" (3.2mm)l control cable from the fuel cock in the cockpit to the valve body,
running through fairleads, pulleys etc.
SAQ 8 What post installation checks are required after a remote fuel system
actuator is changed?
- 26 -
rnoodull l A-1032
Fuel Delivery Pipes (LP)
Fuel pipes are not normally required to handle pressures over 50psi (345kPa)
and are usually made from aluminium alloy with the diameter being large
enough to cope with the flow rates. This is determined by the amount of fuel
the engines need, and typically are about 2%" (64mm)in diameter.
COUPLING BODY
COUPLING NUT /
I '
O-RING SEAL
FITTING END i ,
HALVES
RETAINING RINGS
RINGS
Pipes sections are fitted with various connectors. These need to be fuel tight
using seals capable of withstanding any flexing that may occur (wings tend to
flex considerable during flight and the pipes themselves are not able to take
much flexing). Also all pipe-work and couplings must be electrically bonded
because of the fluid flow inducing static build-up.
* '
Carry out leak checks after assembly. May need an engine run.
* Some airlines require a duplicate inspection on fuel feed leak checks.
-
Where pipes have to pass through pressurised areas (rare) or fire risk areas
additional precautions are taken to ensure that any leakage does not get
outside the immediate viciniwor to any engine hot sections. These features c a n
include such things as scuppers and channels to direct the spilt fuel
overboard. (Engines have a fire-proof bulkhead by regulation). Any couplings
near the engine would be enclosed and provided with an overboard drain.
Pipes also run to the back of the aircraft for tail mounted engines, tail mounted
fuel tanks (aircraft trimming and fuel transfer) or an APU. Here flexible pipes
are used shrouded by a 'normal' aluminium alloy fuel pipe. Any leakage from
the flexible pipe is transferred into the shroud. The shroud is ported to a drain
mast and any fuel accumulation is drained overboard. A standard 'ramp' check
would include checking the mast for any fuel (figure 25). If any is present the
leak must be found and rectified.
Water Scavenging
Water can never be prevented from entering the tanks as it is not possible to
manufacturer fuel that is completely free of H20. To try to prevent a build-up
the water is drained from the bottom of the tanks (water is heavier than fuel
and will sink to the bottom) at regular intervals.
- 28 -
rnoodull IA-1 034
APU SHROUD-
DRAIN LINE
SHROUD APU FUEL SUPPLY
DRAIN LINE LINE & SHROUD
CONNECTION
APU SHROUD
DRAIN MAST
CENTRE TANK
SHROUD DRAIN
LINE CONNECTION
FUEL +
n INDUCE PORT
Figure 26 shows a typical ejector pump used for drawing off the water. It works
on the venturi principal. When fuel is passed through the venturi it speeds u p
a n d the pressure in the venturi decreases (Bernoulli). This allows it to act a s a
vacuum pump drawing fluid (water) through the induce port. The connection to
this port goes to the bottom of the tank, where the water collects and hence it
is sucked out and off to the engines.
NO 2 ENGINE
NO 1IENGINE
CENTRE WING
- LECTOR PUMP
- NO1 MAIN
TANK UMPS NO2MAlN
AFT BOOST
PUMP
Figure 27 shows a Boeing airframe fuel delivery system and figures 28 and 29
show details of the Airbus A 3 2 0 system. Study both systems and work through
them to make sure you understand them. There should be no need to commit
the details to memory. The CAA, however, will expect you to be able to expIain
how a system works; its possible faults and how to rectify them.
FUEL QUANTIW
kgx1OOO- - -
I
REFUEL COUPLING
LEFT CTR RIGHT
Deluel
, TFR
-
- - - Q, PRESELECTED ACTUAL
The A 3 2 0 System
The tanks (1centre tank and 2 wing tanks) are installed in the fuselage centre
section and the wings with the refuel panel being situated in the side of the
fuselage. The refuel/defuel couplings are situated on the underside of the
wings.
The tanks are of the integral type and each tank is made u p of an inner and
outer cell. Fuel transfers from the outer cell to the inner by gravity via inter cell
transfer valves. These are controlled by the low-level sensors in the inner cell.
When t h e fuel level in either wing inner cell drops to the low-level sensor level,
the transfer valves in both the left and right wings will open. There are two
low-level sensors in each inner cell. Each sensor will open two valves, one in
each wing t h u s ensuring simultaneous transfer from each outer cell which will
maintain trim in the roll axis.
,q-- - - - - -- - - - - - -
I
-
R
/
/
..m. .,-
I
A
CROSS FEED
,!'L
E
!'
%
...
-I
CZ
rri I
I
I
I
I PUMP 1 DEFUEL & PUMP, I BOOSTPUMPS I
1
I I I ' TRANSFER 7SEQUENCE I
II
I II I
VALVE I VALVES I
1
I I I
I I
I I I I I
,,
1 ,
REFUEL
I I I I I
VALVE
I I I I
I I
, MNGTANK 1 CENTRE TANK WING TANK
-
I
-
- I
- - - - -
Refuel coupling
COUPLING APU LP
SHUT-OFF
The amount of unusable fuel in the outer cells is reduced by the fitting of two
jet pumps. They use wing booster pump fuel pressure to remove trapped fuel
and disperse water from the floor of the outer, and transfer it to the inner cell.
Each wing tank has a vent system, connected by a large diameter duct, to the
main vent/surge tank located in the outer ends of the wings, which, in turn
vents excess vapour to atmosphere through a NACA duct. The tank vent ducts
are capable of allowing fuel to flow in the event of a refuel valve failing to close.
- 32
rnoodull l A-1038
-
Each outer cell is fitted with an overpressure protector consisting of a carbon
disc, which will burst if the tank is subject to extremes of pressure. When this
occurs, the protector relieves excess pressure into the inner cell, the pieces of
carbon disc being retained by a mesh basket.
Any fuel that enters the ventlsurge tank is recovered into the outer cell by a jet
pump using wing booster pump pressure. The ventlsurge tank NACA duct is
fitted with a flame arrestor, which reduces the risk of a ground fire igniting the
tanks. The vent/surge tank is capable of dumping fuel overboard in the event
of a refuel valve failing to close.
, Fuel is supplied to the left engine from the left wing tank by a pair of booster
. from the right wing @nk by another
pumps. Fuel is supplied to the right engine
p&i "6 bos8tei- p-ciTips. These p-ixLps_~pe12&teat ~ p F i - o ~ i i i a t e ~ y y 2i1~72kFdj.
gs~
Centre tank pumps operate at 30bsi (207k~a), therefore the' centre tank will
I
feed first. 1
I
I
I
~f the bodster pumps fail, then thk- -built-in by-pass valve allbws suction feed by
-
>
I 1';
I
I
I
A cross-feed valve can be selected,which will)'allow the left tank to supply the
I
right engjne and vice versa. I i
l 1
L -
- -1
L-
-
I -'
The centrePtG5k-is fitted with two-bomtef pumps, the left pump2suppliesthe
left engine and the right pump the right engine. They do not have a by-pass
facility, therefore, in the event of both pumps failing, fuel will not be taken from
the centre tank.
By operating the cross-feed valve the left pump can supply the right engine and
vice versa.
The centre tank is vented into the left ventlsurge tank through a duct, which
will only pass air and vapours, it will not pass fuel. If there is a pressure refuel
failure then excess fuel will be passed into the right wing tank inner cell
through a pressure relief valve.
An overpressure protector is fitted which relieves into the left wing tank inner
cell.
- 33 -
rnoodull l A-1039
Once the outer cell is full, fuel overflows into the inner cell. Refuelling is auto-
sequenced:
Each tank feed pipe h a s a refuel valve and a diffuser. The refuel valve is
controlled at the refuel panel by switches and selected closed by high-level float
switches in the respective tank. The diffusers are fitted a t the ends of the pipes
inside the tanks and directs the fuel into the tanks with t h e minimum of
turbulence and electro-static build up.
An air inlet valve is fitted in the refuel line near the refuel valve in each wing
tank inner cell. Its purpose is to admit air into the refuel gallery to permit the
line to drain. Fuel pressure in the line closes the valve. A drain valve allows
fuel to drain from the refuel pipe into each wing tank, except when pressure
refuelling when the fuel pressure will close the valve.
-- ---
When defuelling, the engine feed pumps are used to move fuei through the
engine feed line and then by a transferldefuel valve into t h e refuel line to
discharge a t the refuel coupling.
E A S A ~states
~ that a fuel jettison system is required if the aircraft does not
meet certain climb rate criteria. This has to be done without further
endangering the aircraft or it's occupants and needs to be done quickly.
Consider a n Zircraft on its take off run. Shortly after V 1 (decision speed) it
suffers an engine failure. The pilot has to take-off as h e / s h e has insufficient
runway left to stop the aircraft in time. Once airborne they will want to land
again as quickly as possible. Unfortunately with a full passenger compliment
and full cargo holds and full fuel tanks the aircraft is too heavy and it could
cause damage to landing gear and structure.
Figure 30 shows a B777 fuel jettison system which is typical of many large jet
engined aircraft.
The system utilises the refuel gallery for jettison purposes. The two valves a t
the ends of the gallery are opened together with the two jettison isolation valves
and the fuel is jettisoned a t the wing-tips. The valves are motorised open when
'fuel jettison' is selected and the boost pumps in the centre tank, and the
jettison pumps pump the fuel overboard.
On some aircraft (the B747 for example) the outer tanks gravity feed into the
inner tanks and the inner tanks have jettison pumps.
- 34 -
rnoodull l A-1040
FUEL JETTISON
OVERRIDE/
Control
' 1 \
I '
SAQ 9 What problems can odcur with the aircraft in the jlettison
' configuration and how can they can be resolved?
'
I I
I r -. -
\ --
,
,
\
Selection (and control) of fuel jettison can be!accomplished kither manually or
automatically. Both require pilot initiation. Figure 3 1 showy a manual initiated
and conti-olledjettison system control pantel,.
- --
,
- - -- - /
1
. XmSoN W W I
1
LO t- 10 1 Y"
mrlq-q
O U I O W - M Y
@@
: @@
:
maon vrivu
UmIIY* cw- LID*.."
8 8 8 8
<LOW aw CLOY LIDY
iijj[r.;1gjj
aou SO~A~ICU VALM "OY
w ig-- cloy
The aircrew have to select all these switches to start the jettison process. They
then have to monitor the contents of the tanks to stop any imbalances and to
stop the process at the pre determined level.
The pumps run and the valves open and fuel level tanks starts to fall, as this
happens the FQIS ensures that the aircraft stays balanced. At the required
level the FQIS stops the jettison process.
Figure 32 shows an automated system control panel and the CRT displays. The
data comes from the EICAS (Enane Indication and Crew Alerting System)
computer on Boeing aircraft (ECAM Electronic Centralised Aircraft Monitor on
~ i r b u kArcraft).
1 I
FUEL JETTISON PANEL
1
FLIGHT DECK FUEL
CONTROL PANEL
EICAS DISPLAY
Jettison Safeguards
Computer systems are usually very reliable, and fuel is rarely jettisoned
accidentally. However, errors can happen and the design of a system should
allow for safeguards.
To prevent complete jettison of the entire contents, the fuel for jettisoning is
taken from a higher point in the tank than the normal fuel for engine use.
- 36 -
rnoodull l A-1042
This is typically done by having a stack pipe installed on the inlet, meaning the
jettison pumps will 'suck air' when the fuel gets down to this level whilst there
is still sufficient fuel below the stack pipe available for the engines.
Another, less common, method is to use a float-operated valve that closes and
prevents any fuel entering the jettison system below a predetermined level.
Maintenance of the jettison system is not too unlike maintenance of the system
a s a whole a n d carried out periodically as per the Maintenance Schedule and
will include checks to ensure all the valves and pumps run correctly. In
addition a leakage check of the pipe-work and rear gallery would be carried
out.
the pilot to jettison fuel, hejshei often elects for an overweight landi& instead.
Cost a n d environmental constrdints dictate ,this action.
- -
ll 11 I
-1
I
LONGITUDINAL AERODYNAMIC TRIMMING, FUEL
I
--
SYSTEM^ I
' I I
A s the aircraft approaches the speed of sound (usually with a swept wing
aircraft) t h e centre of pressure moves rearwards and as such the lift force
opposing weight will put the aircraft equilibrium out of balance. This new
moment causes the nose of the aircraft to pitch down (called Mach tuck).
SAQ 10 How is this trim up-set of the aircraft normally countered? C a n you
think when this normal method might not be possible? This Q is not
applicable for those doing module 11B (piston engined aircraft).
An alternative is to move weight (mass) within the aircraft. The most obvious
mass to move is fuel (there is plenty of it and it is comparatively easy to move).
A s it is moved longitudinally the Centre of Gravity (C of G) and hence the
correct longitudinal trim can be obtained (figure 32).
FUEL TRANSFER AFT
FUEL TRANSFER FORWARD
Concorde holds about 33 tonnes (33.5tons) of fuel in its trim tanks. As the
aircraft decelerates from supersonic to subsonic speeds the fuel is transferred
from the rear trim tanks to the forward trim tanks.
Subsonic Flight
Some subsonic aircraft now have fuel tanks in the tail and the fuel is used for
normal longitudinal trimming purposes.
INDICATING SYSTEMS
Manual indication methods were the first type of indication, starting with
dipsticks similar to the dipstick fitted to the automobile engine for checking t h e
oil contents. Variations of the dipstick include the dropstick and the dripstick.
- 38 -
rnoodull lA-1044
Dipsticks are fitted to some older aircraft and are used by maintenance
engineers to give a reliable indication of the contents of each fuel tank.
To use, unscrew the dipstick and remove complete with sealing cap if fitted,
clean with a lint free clean cloth, push back into the tank so that it rests on the
top screw cover, pull out and note on the dipstick where the wetted section
ends. At this point the graduations on the dipstick will indicate the amount of
fuel in the tank. Replace the dipstick, screw into position and lock as per the
AMM.
Figure 34 shows a simplified layout for the dipstick, dropstick and dripstick
systems.
The dropstick is released from the bottom of the tank, the same a s the
dripstick, and allowed to fall under its own weight. It will come to rest when the
magnet in the top of the stick reaches the iron core of the float. The
graduations protruding from the bottom of the tank give an indication of the
tank contents.
Figures 35 and 36 show two methods of manual stick measurement. Both are
unscrewed from their mounting and lowered out of the lower wing surface. In
the case of the sight glass the prism causes the viewing port to turn black as
the prism is immersed in fuel. It is lowered slowly whilst loolang at the prism
through the eyepiece - when it turns black note the graduation showing level
with the tank fitting - this indicates the tank contents.
ii?ods
rnooduli~
QUARTZ
PRISM
TANK
MOUNTING
AND
LOCK
GRADUATIONS
-
Fig. 35 SIGHT GLASS TYPE 'DROPSTICK'
The Dripstick is lowered slowly until the open top allows fuel to spill out of the
hole at the bottom of the stick.' It is then a simple case of measuring off against
the scale and that gives the quantity in the tank.
' I
A development from this is the dripless stick or dropstick (figure 37). In this
system there is a ferrous material target attached to the top of the stick. The
stick is free to move u p and down inside a fuel free tube. The float, which is in
the tankyfloats on top of the fuel and has a magnet inside. When required the
stick is released and allowed to d r o p u t of the bottom wing skin. The target
and the magnet coming together will stop it at the fuel level position.
CALIBRATED
HOLLOW ROD\^)
Fig. 36 DRIPSTICK
The reading can then be read off the scale. Usually this reading is given in
inches and is converted into a fuel quantity by looking up tables in the AMM
and held on the aircraft flight-deck. Care needs to be taken a s the readings
maybe taken back to front.
FLOAT
MAGNETIC
FLOAT
ARMATURE
'i
MECHANICAL INSTRUMENTS
In some cases, on small older aircraft, a manometer type gauge might be fitted.
GEARING
PUSHlPU LL
ROD
6. A capacitive system.
7., An ultra sonic system.
With syktems 1 to 5 a float will be used to move u p and down with the level of
the liquid. When the float moves it will move a variable resister for systems 1, 2
a n d 4;avariable inductor within ac coils for system 3 and a transmitter
synchro on system 5. These systems are all described in the book in this series
entitled Instrument Systems so will not be dealt with further here.
With systems 6 and 7 there are no moving parts and the capacitive system is
the most widely used.
If two metal plates are placed close together (but not touching) with a dielectric
(air or fuel - or any other material for that matter) in between, a capacitor is
formed.
The value of a capacitor is given by the formula:
Where A is the surface area of the metal plates and d is the distance between
them. These two values are fixed by the manufacturer of the unit. The value of
E (lower case Greek letter epsilon) is altered by changing the dielectric constant,
and that happens as the level of the fuel is changed. This is because fuel and
air have different values of E (permittivity).
DIELECTRIC INNER
PLATE
: ;
' ' I
I
,-- -
,
/
-
a
I
.
. +
CAPACITOR j SIGNAL
TANK UNIT i PROCESSOR FUEL GAUGE
: j
I .
i ;
I .
;....;
I
I
.
I
....
Figure 39 shows a simple capacitive circuit with one tank unit. There are
normally several tank units per tank, wired in parallel and supplied with a
small dc voltage. This voltage sets up a potential difference across the plates
between which the capacitance is measured.
- 43 -
rnoodull l A-1049
Figure 41 shows how averaging is achieved. Throughout the tank there will be
several capacitive units and their values will be added and averaged. This
allows for the possibility of the aircraft being in an attitude which causes the
fuel to move to one end of the tank. If, say the tank is half full and this
happens, the tank units a t one end will indicate a full tank and units at the
other will indicate an empty tank - averaged, the values show a half-full tank.
The size of the tank and the shape, dihedral angle etc determines how many
tank units are fitted.
TANK UNITS 2 2 4 . A
/ FUEL TANK
I
TANK AT AN ANGLE SO CAPACITANCE OF CAPACITOR
FUEL TANK LEVEL -CAPACITORS 1 & 2 EQUAL 1 INCREASES WHILST THAT OF 2 DECREASES BY THE
I
SAME AMOUNT
Fig. 41 AVERAGING
- - OUTERTUBE
[GAUGING UNIT]
EFERENCE UNIT
UC-
The outer plate is called the stillwell and allows the fuel to be moderately static
inside regardless of aircraft turbulence, vibration etc.
- 44 -
rnoodull l A-1050
The cables to and from the tank units are low voltage cables and they are all
collected together and passed to a single connection point. This minimises the
risk of fuel leakage.
SAQ 11 What effect on the dielectric constant will a change in fuel density (or
specific gravity) have?
There is a need to compensate for change in fuel density and there are a
number of ways of achieving this. The simplest form of compensator is a small
capacitive unit (called a compensator) that sits at the bottom of the tank, often
close to the sump drain.
Unless the tank is completely drained it will always be totally immersed in fuel.
This means that any change in capacitance of this unit is not due to a change
in the fuel level, but due to a change in the density of the fuel. This signal is
then used to trim the main tank units to allow for the slight changes in the fuel
relative density. This will allowthe--fuel--contents to be given in terms
7- -
of mass
\
arid rlui just vuiuiile, ir i ~kgs
i aiiiilul~lccess~uiiy irl i i i ~ c s
ui g d i ~ ~ l s .
I I \ I
i : \
PRESSURE - --
REFUELLING
CENTRE TANK
FUEL NO 1 TANK
QUANTITY
GAUGES
We shall now consider a 'bridge type' capacitive fuel quantity indicating system.
Once again it is important for you to know the system on the aircraft you are
currently working on, b u t it is also necessary for you to understand the
principles of this system.
The system is used to measure the mass of usable fuel on the aircraft. The
basic principle is shown in figure 45.
SIZE RANGE
- 46 -
moodull l A-105;!
TANK UNITS
I---------I
POTENTIOMETER
FIXED CAPACITOR
INDICATOR CAPACITOR
STAGE
2-PHASE MOTOR -
- FAIL
-
1 I I - SAFE 1
--
REFERENCE CIRCUIT I
PHASE ~1 I ,
I \ 1
2. The current in the top leg of the bridge will fall, because a s the
capacitance has fallen then Xc = 1
{ 2nfc
then Xc must have risen, this capacitive reactance (resistance if
you like) is the opposition to current flow, therefore current must
fall (I = v/ x,) .
3. Nothing a t this time has happened to the current in the bottom leg.
7. The signal is fed to the control phase of the motor. The reference
,-
nLncn
ylluvb farl nff o n n t h e r ceor\nrl=rrr nf the rn a i m c
;n
I" I b U "I* -I" C I I V I "UUVLIUULJ A..
~ trzqc,fc-mel.
LA--
~ ~
A a A C Y a a U -.r
~
The motor drives th&indicator down scale and also the balance
potentiometer towards 'empty'.
9. -
Read through this again carefully, and work through what happens if there is
fuel increase in the tank. A s far as the equations are concerned there is no
need to remember them. There is no need to commit the details of the drawing
to memory either but you should be aware of the principles.
A similar situation occurs when the density of the fuel changes. It will affect all
the tank units in both arms of the bridge and change all their reactance's
(resistance's) so the bridge remains balanced, but one arm has an extra
capacitance unit in the form of the compensator. This means that it will upset
the balance and start a similar train of events to when there is a fuel level
change.
- 48 -
rnoodull l A-1054
Both the tank unit and the compensator signals are fed through cabling to
processor units. These compensate the signals and amplify them. For servo
type instruments the signal is a voltage sent direct to the flight deck
instrument. For CRT/flat screen display systems the signal is sent to display
drivers or symbol generators to provide for flight deck display.
Note. W h e n testing a capacitance type system a capacitive bridge type test set
is used and connected in parallel to the tank units to test points in the system.
An Electronic System
Most modern aircraft have these systems fitted although standby instruments,
similar to the type described above, are usually fitted for use if the normal
system fails. Electronic components are often housed around the display
indicators themselves.
In a typical system (figure 46) the tank unit signals, along with the
compensator signals, as well as dens&, temperature and water detection
(possibly), are fed to a computer, called,(on Boeing aircraft) .a rue1 Quantity
~rocessiligUnit (FQPU). \ I
I
I i I
The signals are sent as either discrete or m!alogue signals. Qnce a t the
/
computer they are converted into digit&d,dta by the analo@e t o digital
convertei (AID converter), theniprocessed~throughthe CPU ( d e n t r d Processing
1
Unit). 1i
'\
i '\\
1 ! "
FQPU
The signal is sent to the refuel panel (IRP) for display during refuelling. It is
also transmitted to the display drivers (called various things such a s Symbol
Generators but in figure 45 they are called AIMS - A Boeing term meaning
Aircraft Information Management System - and then onwards to the CRT
screens in front of the pilots.
It is displayed on the top centre screen a s a total quantity. (Most 'glass cockpit'
displays have 2 screens in front of each pilot for HSI and AD1 displays, or
similar, dealing with aircraft attitude, direction etc, and two centre screens
showing systems status [hydraulic, fuel, elect, engines etc].
Boeing call this screen system EICAS and Airbus use the term ECAM.
Fig. 48 A DENSIOMETER
'50
moodull 1 ~ ~ 1 6 5 6 -
A button can be selected to bring u p more detailed information of the fuel
system. See figure 46 a n d the books in this series entitled O n Board
Maintenance Systems.
The densitometer will accurately measure the density of the fuel in the tank.
Again located in the bottom of the tank, to ensure that it is always immersed in
fuel. It is composed of a nickel alloy, wire wrapped spool, and an excitation coil,
a sensing coil and trim resistors all contained in a vented housing. Different
sized connectors help 'Murphy' proof the electrical connection.
Dense-fuel will slow the spool-down more and this 'slowing'or change in
vibrations frequency is felt by'the-sensing,coil. This is fedback-to-the control
unit (FQPU) for processing and used to calculate the mass of the fuel.
l 1
The densitorneter is accurate d d can woik'out the relative dehsity oh the fuel
to two decimal places. It also h a s anoth'er function. If the relative density starts
to climb towards 1.O, it can be assumed ,that water h a s collecting &,the bottom
of the t d k . I \
-I
'\
AN ULTRASONIC SYSTEM
This system senses fuel tank quantity by ultrasonic fuel probes. These and
other signals are processed by a Signal Processing Unit which is controlled by a
CPU. This unit will send fuel quantity information via a n ARINC data bus to
flight deck displays a n d other systems requiring the information.
The 'time of flight' of the ultrasonic wave from the transducer u p to the fuel
surface and back is a function of the immersed height of the fuel probe and the
propagation velocity in fuel. By means of a reference flange in the still tube at a
reference height from the transducer a second reflected signal is produced.
Assuming that the propagation velocity is the same in both the calibration
wavefront path and the surface wavefront path, then the height of the surface
may be calculated directly without reference to the propagation velocity.
Thus the fuel level is determined ratiometrically. Fuel height signals from the
numerous probes within the tank are used to calculate the volume of fuel
contained within that tank from stored tank shape data. Volumetric quantity is
then converted to mass using the signal from the densitometer (working on thp
vibration principle). Fuel quantity in terms of mass is then sent to cockpit
displays ,&d aircraft systems. - --
The datLr detector consists of the basic transducer housing assembly minus a
still tAbk and is mounted at the lowest point in the fuel tank where water will
tend do collect.
---
I '
INPUTIOUTPUT
/ \
<
TOIFROM AIRCRAFT
SYSTEMS
>
ARlNC
629&
429
,,>
<
\ /
CENTRAL
PROCESSOR
UNIT (CPU)
- SIGNAL
PROCESSING
UNIT (SPU)
FUEL TANK
rnoodull l
-
A-1058
52 -
The microprocessor-based control unit provides:
Fuel surface attitude information can be computed from fuel height data of any
three probes in any one tank. This allows compensation to be applied to fuel
volume calculations based on stored tank geometrical data and compensation
for aircraft attitude variations.
In the event of densitometer failure, fuel density can be inferred from the
empirical relationship between fuel density and propagation velocity. This
calculation uses the time of flight to the reference flange from a number of fuel
probes. Fuel stratification effects can also be identified by comparison of the
propagation time for a number of fuel probes at differing heights within the
tan2;'.
That concludes this book on EASA module 11 fuel systems. To consolidate
your knowledge try the following exercises:
Answers to all the above (except number 23) are to be found in the text.
SAQ 1. An aircraft fuel system constitutes: Storage, Refuel and defuel systems,
engine fuel feed, jettison and indication systems. The start of the fuel system is
where the bowser/tanker connects onto the aircraft, and the aircraft fuel
system ends at the LP - Low Pressure cock, or LP SOV - Shut-Off-Valve.
SAQ 2. Flexible tanks have the advantage that they can be made to fit any
cavity shape. They are fairly easy to replace and as such, leaks in the tanks
can be easily found and fixed. Unfortunately they are fragile and prone to
deterioration. They add weight to the aircraft. Leaks in the bags may not be
detected until there is a build u p of fuel in the structure. They are more crash
proof than the other type of tanks as they can take some distortion without
rupture.
SAQ 4. ATA chapter 12 gives details of servicing. You may, however, have to
look in ATA chapter 6 to find details of the refuel panel location.
SAQ 5. Carry out operations as though you were to defuel the aircraft. Without
the bowser connected and hence the NRV7sclosed. The fuel will travel from the
forward gallery onto the rear gallery. Now we can select a refuel valve open
from the refuel panel and then transfer fuel from one tank to another.
SAQ 16.-No-is the answer. Due,to the fact that there is only one-pump in the line
if this were to seize then fuel could not get'to the engine. The usual way of
allowing for this is to provide a byPass pipe,'with check v q . u n d e r normal
operatiod the check valve stays closed by fukl pump pressuie. If that pump
fails tKe engine will 'suck7and l-ience open the check valve y d allow 'fuel
through. - -
I
I - .
\ i I --
SAQ 7.' If; there were a Centre Wing Tank (CWT)this would be ernptred first so
that the
I
weight isieduced from itfie fuselage section. Also, kkebing weight
within the wing &d hence downward force oh the wings, counter balances the
upward force,of lift. (This reduces the b p d i n g moment of thje %ng which can
be dcsigna_as a lighter strucpre). This is achieved in one of two ways. Boeing
uses higher pressure boost pumpsin the CWT, causing it to empty first. Airbus
generally uses a single point sensor that allows a float to open when the CWT is
empty.
SAQ 8. This follows a similar pattern to the post-fit tests. Check for security of
the component; ensure it is correctly orientated and the screws are tight and
wire-locked if required. Don't forget the electrical plug, usually a standard
Arnphenol type connector and will have witness marks to show correct locking.
A bonding check will be required in common with all fuel system component
changes. Finally it will need a functional check iaw the AMM.
Carry out the specific AMM checks for replacement that are likely to include
open and close checking against the manual indicator. Carry out flow (and no-
flow) checks with a number of boost pumps running - these checks ensure the
valve opens fully, closes fully and that the thermal relief hasn't failed.
Your company may require a duplicate inspection and all work must be
recorded in the aircraft log book/work record cards together with part
numbers, any test data etc. All work must be signed for.
S A Q 9. Some of the problems that could occur are the fuel coming into contact
with hot exhausts. This is covered by fitting the jettison pipes usually at the
extremities of the wings away from any heat sources.
SAQ 10. The stabiliser (tailplane) trim mechanism to move the stabiliser nose
down (decreased angle of incidence) causing an opposing nose u p pitch. This
will counter the natural nose down tendency of Mach tuck. This is the usual
way to counter Centre of Pressure changes.
SAQ 11. If the relative density (or specific gravity) of the fuel is lowered the
dielectric constant of the fuel is lowered. So applying the capacitive equation
we can see that the capacitance will also be lowered.
- 56 -
rnoodull lA-1062
CONTENTS
Page
Principles
Hydraulic fluids
Hydraulic systems
Power circuits
Consumer circuits
Hydraulic components
Emergency/ standby systems
The power pack
Hydraulic seals
Pipelines
Flight deck indications
Maintenance
PRINCIPLES
Before we start looking a t hydraulic systems you must have a knowledge of some
of the rules and laws which govern the behaviour of fluids under pressure.
I r
Where P = Pressure
F = Force
A = Area
Metric (SI) - Pressure = The Pascal (Pa). 1 Newton per square meter = 1Pa
Force = Newton
Area = rn2
Note. The Pa is the Pascal (named after Blaise Pascal 1623-1662). This is a
very small unit with nearly 7000Pa to just lpsi.
Pascal's Law states that fluid held under pressure in a container exerts pressure
equally, instantly, and a t right angles to all surfaces of the container without loss.
Brarnah's Press. Sometimes called a Hydrostatic Press, it is used to magnify a
force. It i s a hydraulic press consisting of two cylinders - one larger in diameter
than the other. Sealed pistons are allowed to move within each cylinder.
I n general a small force on the small piston will create a large force on the large
piston. But in pushing the larger piston u p the smaller one will have to move
through a larger distance.
During operation the parameters that are common for both cylinders are:
In other words the pressure is the same in both cylinders and the total volume
displaced from one cylinder is the same as that received by the other.
-- - -
I
SMATL- pp
\ i PISTON - - .
I
,
I
I LIQUID LIQUID
i '
I
I
I )
I '
I
-4
- Fig. 1 THE BRAMAH PRESS
Example
Take the approximate sizes of an aircraft hydraulic lifting jack. The piston that
pumps the jack u p is about 0.5 inches in diameter and the jack body piston being
about 3 inches in diameter.
QUESTION: Given the above diameters of the pistons can you work out their
areas? (5 mins)
= n x 0.5 x 0.5 = n x 3 x 3
4 4
= 0.2 in2 = 7 in2
-2-
rnoodull l A-1065
LIFTING JACK
SMALL PISTON
LARGE PISTON
VALVES \
PRESSURERELEASE
VALVE
In general calculate the pressure in the small cylinder then use this pressure in
the large cylinder to calculate it's force.
-- -
Pressure equals force per unit area.
I
I
1
pressure = force p '=
area A
-
SMALL PISTON
0.5" (12.7mm) DIA
LARGE PISTON
3" (76.2rnrn) DIA
2. This is also the pressure in the large cylinder. So the force on the large
piston equals = F = P x A = 450 x 7 = 3 1501bf.
Areas:
SMALL PISTON LARGE PISTON
&
2 &
4 4
= n x 0.013 x 0.013 -
- n: x 0.076 x 0.076
4 4
= 0.0001 m2 - 0.004 m2
-- -- --
J
r -
,
- -
-. -.
The paessure in the system with 4 901b force on the small piston is:
(901b prce is approximately equ'alto 40 1 Newtons).
i
I , ' I
I
-
- -
'
3
i \ i
1 I \ or 4,010,000 Pa I I
1
~ : I
I I
I , , oi- ; 4 MPa pressure approx.
- 1 \--- ,' -
- -
~ h i b ~ r e s s u r e iact
l l on the largeFpiston = pressure x
area.
All the above calculations assume that there are no losses in the system and no
friction to overcome in the seals.
ANSWER: No - there are losses in all systems. But for general calculations it is
assumed that it is true and the answer works out quite well.
QUESTION:Can you work out how far the large piston will move up when the
small piston is pushed down?
-4-
rnoodull l A-1067
If your answer is NO then refer to the answer below.
ANSWER: Remember the basic rule - the volume displacement from one
cylinder is the same volume displaced to or from the other.
Sovolume = nx0.5x0.5 x 4
4
= 0.8in3 approximately
Volume = V = Ah -
h= y I
, --
A = 0.8
7 = 0.1"
I ~
It doesn't move far does it? - bearing in mind the movement of the small piston is
4in. When you jack an aircraft just-note the differences in the movements of the
jack piston for each stroke of the pumping piston.
With reference to figure 2. When the pump piston is moved u p it draws fluid in
from the reservoir via the one-way valve. When it is pushed in it pushes the fluid
out to the jack via the other one-way valve. To lower the jack the release valve is
opened which allows fluid in the jack cylinder to return to the reservoir.
HYDRAULIC FLUIDS
Almost any type of fluid can be used in a hydraulic system, but the special
requirements of aircraft systems have resulted in the use of vegetable, mineral
and synthetic based oils. They must meet the requirements laid down by the
regulatory authorities (EASA 2 5 for large aircraft, 23 for small aircraft, 27 for
small rotorcraft and 29 for large rotorcraft).
- 5 -
ANSWER: It is the resistance to flow of a fluid. The higher the resistance, the
higher the viscosity and the more energy the fluid requires to be
pumped around the system. Viscosity may change with temperature
c (called 'viscosity index'))- usually the higher the temperature the
I
I
1
'
,
lower the viscosity. I
I
, I - . \
I I, I
Fluids are coloured which helps recognition, but in general fluids should only be
used if they are from an approvrd 1supplier; in sealed containers; to the correct
specification - as laid down in theAMM (Aircraft Maintenance Manual).
I I I
Fluidd tb different specification: must never be mixed. Fluids to the same
specification, but produced by different manufacturers, may be mixed when
perrnittdd
- i n the 'AMM. -
i -_ --- - - -- /
Use of a fluid, which is not approved for a particular system, may result in rapid
deterioration of seals, hoses and other non-metallic parts. It may also cause high
wear rates and allow sludge to form.
Types of Fluids
There are many types of fluid on the market and it is most important that the
correct specification fluid is used a s stated in the AMM. Below are listed the more
common types:
LOCKHEED 22. (to MIL SPEC H-7644). Vegetable based and almost colourless -
but a slight brown/yellow hue. Pungent smell. Used with natural rubber seals
and hoses. Used in some braking systems but not often found in modern
hydraulic power systems.
rnoodull l A-1069
DTD 585. (to MIL SPEC H-5606). Mineral based and coloured red. Uses synthetic
rubber seals and hoses. Used in hydraulic systems and landing gear shock
absorber struts. Excellent lubrication and ant-corrosive qualities, but flammable.
SKYDROL. (to MIL SPEC H-8446). Phosphate ester based (synthetic) and may be
green, purple or amber in colour. Used with butyl rubber, ethylene propylene, or
Teflon seals and hoses.
Widely used on modern aircraft because of its fire resistance - though high-
pressure spray is combustible. Temperature operating range is between - 65°F
and + 225°F (- 54°C to +107"C). This fluid requires care in handling a s it is an
irritant to skin and eyes.
Avoid contact with the body and avoid inhaling the fumes. Always use a barrier
cream and protective clothing such as fluid resistant gloves, goggles etc. It will
absorb atmospheric moisture and attack most plastics and paints (though not
epoxy and polyurethane based paints). May become acidic if overheated.
-- - -
HYDRAULIC SYSTEMS I
Hydraulic systems are used to operate such services as landing gear, wheel
brakes, powered flying controls, windscreen wipers, flaps, spoilers etc. Each of
these services has its own hydraulicEirCuit within the hydrauliC system. These
circuits are usually connected tq supply and return lines running to and from the
supply circuit. Thus the complete system is made u p of a supply circuit connected
to various service circuits. I
O n many *craft more than one hydraulic system is provided and these may be
interconnected. On most large aircraft three (or even four) independent systems
are used, each with it's own supply pumps, reservoirs, pressure and return lines.
Each system supplies it's own services with the more important services receiving
supplies from more than one system.
On most large aircraft the Powered Flying Control Units (PFCUs) for example,
receive three independent supplies (the A380 is different in that each PFCU is a
self contained electrically powered hydraulic system unit located a t the control
surface). Emergency circuits may be provided for use in the event of hydraulic
system failure.
Figure 4 shows a basic hydraulic system, which can be made to do work. With the
pump running, fluid is drawn from the reservoir and supplied to the selector valve
under pressure. When the selector valve is rotated one side of the jack is
connected to the supply whilst the other side is connected to return. The jack will
move. Returning fluid will go to the reservoir via the selector valve.
rnoodull l A-1070
RESERVOIR DIRECTION OF FLUID FLOW ---*
n
I -RETURN LlNE
I ;:P"
-.-
-
--
I
--
'
A) Y/ Valve selected to allowjack to move in the opposite direct~on
--
I
l 1
l 1
The selektor valve may be mandally or electrically operated. The drawing shows a
simple rotating type of selector valve, buttsome are operated by a slide,type
piston.I II ' I
I
With the valve as'shown the fluid! Icauses the jacklactuator tb retract (move in) -
with the -valve
-- rotated clockwise by 90° the supply will be connected to the bottom
of th2jack and the top will be connected goo.;eturn.The jack will extend. This is
called a two-way selector valve- used for systems where only f i l l y in or fully out
selections are required, eg landing gear.
Where intermediate selections are required - flaps for example - then a four-way
selector valve will be used. In the drawing it is similar to the one shown but it can
move 45"from the position shown so not aligning it's ports with any of the
connections - supply, return or the jack connections. In this position it will form a
hydraulic lock between the valve and jack and the jack will not move.
(2) If the ambient temperature rises the fluid temperature will increase and the
pressure will increase. The pressures can get so great that structural failure of the
pipes/components will result. Thermal relief valves are fitted to prevent this -
more on this later.
The pipeline leading from the reservoir to the pump is called the suction line, with
the line running from the pump to the selector valve the pressure line, and the
line returning to the reservoir the return line.
Most aircraft have systems which are more complex than the one shown above. I t
( does not have any provision for pressure relief, off-loading the pump, standby
suppiies etc. Reai systems have ail these, and for ease of ieGninC%-e'spiit into
sub systems, eg power circuits, brake circuits, landing gear circuits etc.
There are two main types of system in use, the open-centre system and the closed
system. The former is most usually found on some light aircraft a n d is not well
known. The latter is common and found-on'most aircraft - large argl small.
-
I
The Open Centre System (figure 5)
The main advantage of this system is its simblicity, and the main disadvantage is
that only one service can be operated a t a time. When no s e ~ c e s l a r being
e
operated the pressure in the system is a t a low value, with pump output passing
directly to the reservoir round the 'open circuit' - with all valves in the open centre
position.
RELIEF VALVE
I
I SERVICE 1 SERVICE 2
With all selectors in this position the fluid is pumped around the system under
very little pressure - thus saving energy consumption by the pump. Should there
be a delay between the jack getting to the end of its travel and the de-selection of
the selector valve, or should something fail, then there is a pressure relief valve to
relieve excessive pressures.
With this type of system, operating pressure is maintained in that part of the
system which leads to all the selector valves, and some method is used to prevent
over-loading the pump. All consumer circuits have the same pressure supply -
but s h g e the flow rate so individual flow rates might be different.
-- - - -
- -1 -- - -
- -2 I
-
- ;'ACCUMULATOR
' +
~ I
+
/
/' IDLING
CIRCUIT - -
-/-
-- - _,
I I
Fig. 6 SIMPLIFIED CLOSED SYSTEM
-
SERVICE I It SERVICE 2 /
- 10-
moodull l A-1073
In some simple light aircraft systems, operation of an electrically driven pump is
controlled by a pressure-operated switch, which may be part of a power-pack
assembly. The pump comes on when required and switches off when system
maximum pressure is reached and no component is selected.
POWER CIRCUITS
The power circuit supplies fluid to, and accommodates the fluid returned from,
the other circuits. It may also contain more than one pump. Pumps are usually
engine driven, but may be electrically driven. The power circuit may contain one
or more of the following components:
Driven pumps. Driven by: the enginels, electric motors, air (the ram
air turbine [RAT]),hydraulic (power transfer units).
Automatic cut-out valves (if constant volume pumps fitted).
Pressure relief valves.
- - -
H=d p I I 1 p s .
Reservoirs.
Reservoir pressurisation system.
Reservoir pressure refill connection. I
Oil coolers (in the fuel tanks). '
Accumulators. - -
-
Filters. I
\
Priority valves. I
In multi-engined aircraft it is usual to have each power circuit using two or more
pumps. They may both be engine driven (from different engines), or one may be
engine driven and the other driven by hydraulic pressure from another system
(power transfer unit), or electrically, or ram air operated. On small aircraft there
may only be one pump and one supply system.
Figure 7 shows a circuit fitted with two self-idling (constant pressure) pumps,
which, should one fail, will still provide fluid flow but a t half the normal rate - so
all systems will work but a t half the normal speed.
The self-idling nature of the pumps means that they will automatically adjust the
flow rate to suit the demand, and completely shut-off the supply when demand is
zero - although they run continuously. The idling line (case drain line) will allow
fluid flow to the reservoir when in idling mode to keep the pump cool and
lubricated.
rnoodull l A-1074
GAS CHARGING
CONNECTION
PRESSURE
GAUGE
RESERVOIR GROUND TEST
CONNECTIONS ACCUMULATOR
TO NON ESSEKTIAL
SERVlCES
DRIVEN WMP
1 :v////.
1 ;:En
TO ESSEUTM
SERVlCES
COMMON RETURN
1 = PIPEUNE; I ----------= ELEcTiaca CoNwcTtms ,
I , I /
Fig. 7 TWO PUMP POWER SUPPLY CIRCUIT USING SELF IDLING PUMPS
I
-
----
,
I --
The pip+ines to the pumps are $led suZtion lines; from the pumps are called
pressure lines and idling lineslcase drain. I
I i ' I
A s an additional safety factor, some aircraft are fitted with a high-pressure relief
valve in the power circuit - in case the pump fails to off-load.
The gauging (fromthe pump) includes a pressure gauging system (moving coil, dc
or a c ratiometer, or synchro systems) a low pressure warning system (Bourdon
tube or bellows operated micro-switch) and an oil temperature indicating system
(thermister - moving coil or dc ratiometer systems). Gauging a t the reservoir
includes: oil level; temperature, and pressure - if the reservoir is of the
pressurised type.
rnoodull l A-1075
Over-temperature warning may indicate a failing pump; lack of fluid supply or
reduced cooling effect to the returning fluid. In the event of failure of the engine-
driven pump, the "second" pump will maintain the supply (but a t half flow rate);
the hand pump, if to the flight crew, could be used in a n emergency.
The hand pump has its own filter, pressure relief valve and non-return valve.
Both hand and engine driven pumps are provided with non-return valves to
prevent the flow of fluid from either pump by-passing back to the reservoir
through the pump not in use.
When the aircraft is on the ground, the hand pump can be used for maintenance
purposes - operation of cargo doors, bleeding etc.
Some circuits are of vital importance to the safe operation of the aircraft, whilst
others are of lesser importance. In general, PFCUs), wheel brakes and other
essential services must have priority over non-essential circuits such a s powered
nose wheei steering and ianciing geeex~ension.Snouici the power clrcuit supply
pressure fall below a pre-determined figure, a priority valve shuts-off the flow of
fluid to the non-essential services and maintains the fluid prdssure fo; the
I
essential services.
The priority valve may be situated a t the power supply circuit (as shown) with a
pipeline going to all essential services and another pipeline going to allmon-
essential services. Alternatively, the valve may be fitted a t the supply point to each
non-essential service to shut it off in the event of reduced supply pressure.
I
i !
-
ANSWER: The landing gear has it's own emergency down systems - to include
'freefall', gas operated, separate pumps etc, and steering the aircraft
on the ground can be achieved by differential braking if the nose
wheel steering fails.
During servicing of the aircraft it will be necessary to test the hydraulic system,
but a s the engine cannot always be used to run the engine-driven pump (when
landing gear retraction testing for example), ground test connections are provided
which connect the power circuit to a ground engine driven hydraulic servicing
trolley (cart).The ground test connections are of the self-sealing type - either
screwthread or bayonet type - usually of different sizes so cross connection is not
possible.
Of course, the hand pump may be used for testing purposes, but the rate a t
which it can deliver fluid is very slow and it will not reproduce actual operating
conditions.
GAS CHARGING
CONNECTION
COMMON RETURN
I
= PI~EUNES ......-.----..-------=
ELECTRICAL CONNECTIONS
~
I
1
I
- --
-.
I
i
The constant volume pump s h o ; ~ ?in figure 8 (which pumps fluid all the time it i s
running) will need some form 06 '~ressurereliefywhen services do not need fluid.
If an ~ r d i n ~ , ~ r b s s relief
u r e vqvk was fitted:in the system it would do the job,
I I
but ,at an energy cost. The pump would have to keep pumping at it's normal
working-pressure to keep the pressure relief valve open - using energy (fuel) all
the time. So a special relief valve is fitted called an Automatic Cut Out Valve
(ACOV).
When operated it allows the pump to pump fluid at almost zero pressure via the
idling line or case drain line back to the reservoir - keeping the pump lubricated
and cool. More of this later.
Note. The two circuits shown above have two driven pumps each but may have
only one pump on some aircraft, and may have three on others.
A 3 2 0 System
Take a moment to study the system and note its main features. It has three
systems - blue, green and yellow. All have accumulators with priority valves in
front of the non-essential services.
mRESERVOIR RESERVOIR
PUMP
140 L/mn 140 L/mn 25 Llmn PUMP
37 Usq/rnn 37 Unq/mn
aLa RELEVATOR
Wl
LANDING GEAR 1
The pumps include a hand pump (for cargo door operation), Ram-Air driven
Turbine (RAT) - for emergencies, engine driven pumps and electrically driven
pumps.
A power transfer unit is provided between the green and the yellow system. Note
that some services have three supplies - PFCUs for example, whilst others have
only one - landing gear and steering.
Figure 10 shows the power supply circuits of the Boeing 757. Take a few moments
to study the drawing.
- 15-
rnoodull lA-I078
-3 SUPPLY
PRESSWE
3 m RETURN
AIR
EOP - ENGINE D R l V E N P W P
ACMP - ALTERNATING CURRENT llOTOR PUMP
RAT - RAM A I R TURBINE
PTU - W Y E R TRANSFER U N I l
SOV - SHUT OFF VALVE
With reference to figure 10 note the following:
* Three systems (left, centre & right) using seven pumps.
* Pumps: 2 Engine Driven Pumps (EDPs) 3000psi @ nearly 40 galls
per minute; 4 electrically driven pumps (ACMPs).Pressure supply
similar to above but low flow rates (about 7 galls per minute; 1 RA - for
emergencies - manual or automatic deployment based on both engines
low rpm - also possibly connected to airspeed and weight switch inputs.
Driven by a V P propeller and supplies about 2000 psi at about ?A of the
normal pump flow rate; 1 air driven pump (additional pump on the 767
fitted to the centre system).
* Single point reservoir filling.
* Fire Shut-Off Valves (SOVs).
* Pressurised reservoirs.
* Fuel cooled heat exchanges.
* Power transfer unit. Comes on automatically when left engine rpm or
left EDP pressure is lost. Is a bent axis hydraulic motor driving a
hydraulic pump. About 2,000 psi a t about half the normal pump flow
- --
rate.
I
I
'
Note the power supplies to the following consumer circuits:
* Wheel brakes - 2
* Powered steering - 1
* Landing gear retraction - 1
* Flaps and Slats - 1
* Yaw damper - 2
* Tail plane trim - 2
* ~ u t pilot
o servos - 3
-
* Spoilers - 3
* Thrust reversers - 2
CONSUMER CIRCUITS
These are circuits/services that use the pressure supply from the supply circuits.
Remember that for most aircraft all services have the same pressure supply
(unless there is a pressure reducing valve fitted) but they will share the fluid flow.
This means that if more than one circuit is selected a t any one time then the fluid
flows to all the circuits will be different.
Consumer circuits can include all those listed for the B757 plus windscreen
wipers, cargo door operation, hydraulically operated pumps etc. Each consumer
circuit will have a pressure supply line and a return line from/to a supply circuit
with, if necessary, switching provision to other supply circuits.
- 17 -
rnoodull l A-1080
Alighting Gear Circuit
The circuit illustrated shows the layout and components required to control the
raising and lowering of one landing gear unit with the other units having a similar
arrangement - with the selector valve being common for them all. Fluid is
supplied from the power circuit to the control valve via a non-return valve. This
valve ensures that the alighting gear circuit is isolated from the rest of the aircraft
hydraulic system by providing a hydraulic lock.
The control valve, which may be manually or electrically selected, directs fluid to
the desired end of the jacks/actuators and at the same time connects the other
line to the reservoir. The lines to/from the actuators are known as the up and
clown lines.
!?herma1 Relief Valve (TRVI. Due to thermal expansion of the fluid (eg, hot
climates, operating temperature rise etc) in a closed circuit, there is a risk of burst
pipelines and damaged components. To prevent this a thermal relief valve is fitted
in both the u p and down lines.
The valves will relieve expanding fluid to the circuit return line. They are pressure
operated and designed to relieve a certain amount of pressure whilst leaving some
pressure behind.
One-way Restrictor Valve. When alighting gear down is selected the free fall
(static drop) of the alighting gear could damage the undercarriage unit attachment
points on the airframe and cause cavitation in the down line (the fluid being
drawn by the falling undercarriage quicker than the pump can supply), therefore,
to slow-down the rate of fall, a one-way restrictor valve is provided in the up line.
This valve, which restricts the flow of fluid in one direction, but permits full flow
in the opposite direction, offers no restriction to the flow of fluid when alighting
gear up i s selected. It prevents fluid getting away from the jacks too quickly when
down is selected - thus slowing them down.
Shuttle and Fluid Jettison Valves. Separate the Alighting Gear circuit from the
Emergency Down gas operated circuit. They allow the landing gear to be "blown
downn'"in= emergency such as total-kydraulic failure. More details -
later.
- \
\
~echa!nJcalSequence Valves (Single Sequence Circuit\. To avbid collision between
the ulddrcarriage leg and it's fairing door dqking operation, the' undercarriage
compo,nents must move in the correct order,(or sequence). For example the
undercdriage leg must fully retract before~it'sfairing door start$to close. A
typical skquencing operation would be: -, \ ,
'
1
1 ,
I
Landing gear without fairing doors do not require this system and some aircraft
with fairing doors have the doors mechanically connected to the main
undercarriage leg and, therefore, employ only one operating jack.
rnoodull l A-1083
Up selection Door opens
Leg retracts
Door closes
Additional sequence valves are fitted to cope with a double sequence system or the
system is electrically controlled.
Emergency Operation. Many large aircraft have a free-fall emergency facility and
some have a separate dc motor driven pump and hydraulic system to lower the
landing gear should all else fail. The one shown has a gas operated system. Some
have a manually operated wind-down system.
Tlne gas operated system has nitrogen stored under pressure in the gas bottle.
S'hould an emergency arise and the undercarriage fail to lower by the hydraulic
system then the pilot can operate a manually operated emergency selector. This
allows nitrogen under pressure to the shuttle and jettison valves.
TL'3 " h , ? t t l n r r n l ~br n~u
1 J L I ~O L r u L L r b v - v
;c ,-.~??cC.A
b u ~ u v
tn
u
-nT,L c,,V-r.&"
c u r_lrurb u b s u u
0-#-I
L~
UAU
-0-
~ U
,,+-,Aev
ULICLUI
V
+-.+-a""7,va
~ A L O U UL
~
z-+o+--+La
u CIIL
LIICLL
-- -
undercarriage down line. The door jack, sequence valve, and leg jack operate as
I
normal.
Returning fluid from the circuit has to be,hllowed to be jettisoned (the emergency
could be a jammed selector valve --or loss ,df electrical power to the valve, if
electrically operated). So the compressed gas operates the jettison valve which
allows returning fluid to be jettisoned overboard. I
I
I I
On some small aircraft the brakes may be operated by a lever and cable system -
operating a drum, or brake calliper and disc assembly. On many light aircraft a
small hydraulic system is provided. Figure 13 shows such a system.
When the toes are pushed down (on the rudder pedals) on the foot motor,
pressure in the hydraulic fluid causes the brake cylinders to operate. When the
toes of both feet are pushed down in-line braking is achieved, when one is pushed
down, one brake will operate and the aircraft will turn.
- 21 -
If the flaps are operated using hydraulic motors - as with many large aircraft -the
fl,aps will have a separate load relief system. This consists of a Pitot operated
pressure capsule connected to a motor connected to the flap selecting linkage.
(With flaps down, a s the airspeed increases so the Pitot capsule will make an
electrical contact to select the motor to move the flap selector linkage to select the
flaps to a higher position) - with pilot warning.
QUESTIQN: Why could the flap circuit (or any other circuit for that matter)
I ' have a varying flow :ate supply? Surely the pump, particularly a
1 1
constant delivery pump, will supply the fluid a t a!cgnstant rate.
! '
I ) (5 mins)
I --
ANSWER:
I If a second circuit id selected, thin fluid supply fqom the purnp/s
I
QUESTION: SO why is it import8nt'that the flaps always move at the same speed
each time? (I'm not talking asynchronous here). (5 mins)
A.NSWER: Operation of the flaps causes a trim change of the aircraft. This
must be the same on every flight so that the pilot knows how
to react. So the throttling valve sees to it that the flaps always move
at the same speed each time they are selected.
When a selection is made fluid flows to one side of the operating jacks. Returning
flluid from the other side of the jacks goes via the selector valve to the reservoir
through the return line. Irrespective of the selection the fluid flows through the
throttling valve which ensures a constant rate of flow at all times - IN & OUT.
rnoodull l A-1086
PORT STARBOARD
OPERATING
Flap Synchronisation
-- - - - - -----
Port and starboard flaps must go u p and down together, if they do not for any
reason, a roll would be induced. If this happened a t low altitude a crash would b e
almost inevitable. (In the 1960s a BEA Elizabethan twin engined aircraft carrying
show horses rolled violently on approach to Heathrow airport. It crashed killing all
the crew a n d the horses, a n d writing-off other aircraft on the ground. The cause
was a failed flap operating linkage on one side of the aircraft. The incident was
caught on movie camera by an amateur camera man.)
rnoodull lA-10187
SYNCHRONISING JACKS
OPERATING JACKS
Tliey are cross connected in such a way that if one flap is moved the other will be
folrced to move in unison because of the tr-ansfer of fluid from one side of the first
jack to the other side of the second jack.,Fluid make-up valves and tQermal reliei
valves are fitted to the cross feed lines (not shown in the dradirig). \
I I ~
1 '
I
DRIVE SHAFT
RPM PICK-OFFS
MECHANICAL
- 25 -
rnoodull l A-1088
The screw jacks are rotated using drive shafts and gearboxes. The drive shafts are
rotated using a duplicate system of hydraulic motors.
Flap asymmetric operation is prevented, in the first instance, by the drive system
being common to both sides, but if it does happen it is detected by detectors at
the end of each drive shaft. The detectors pick up the drive shaft rotation and
send the signal to the asymmetric detector unit.
This unit compares the signals of both sides and if one shaft rotates quicker or
slower than the other then the fluid shut-off valve is caused to operate. This stops
flap movement and warns the pilot.
This type of system is also used to operate the leading edge slats/Krueger flaps.
Air speed sensors will operate to select the flaps u p (a small electric motor
changes the effective link length or a computer operates the normal flap selection
system) if for any reason they are left down in an accelerating airflow (after take-
off fo< e x e p l e ) . If the flaps ar_e selzted
-- -- down at high speed the air speed sensor
will pqevent the selection being made to the hydraulic motors.
I
1 I
1
: 1
The ~ 3 2 ) Flap
O System (figure 17)
/
I
This is similar in principle to the system-s,hown in figure 16. Each Power Control
Unit (PCU) is supplied by two hydraulic systems and these operate drive shafts to
operate the flap drive gearboxes.
I
~syn$ne@-ydetectors fitted a t each drive shaft end monitor their rotation and
infoms_the computer if the flaps move asymmetrically. If detected the computer
will stop the flaps moving and send a warning to the flight-deck.
When the pilot makes a selection via the computer the hydraulic valve on the
hydraulic motor selects and the motor causes the drive shafts to rotate. A s the
shafts rotate so a pick-off on the motor power control unit sends positional
feedback information to the computer. When the flaps get to the selected position
the computer will operate the control valve to the mid-off position to stop the
motor - the flaps being held in their new position by a hydraulic/mechanical lock.
ANSWER: It can be defined a s a system where the output of the system tries
to cancel the input.
Surface support track
Flap (and slat) positions are indicated on the flight deck by ECAM (Electronic
Central Aircraft Monitor). The signal will go via a Symbol Generator Unit (SGU) to
be displayed on a CRT (Cathode Ray Tube) in colour. The slat operating and
asymmetric detection system operate in a similar way to the flap operating and
detection systems.
Figure 18 shows an older type system. Typically two supplies are provided - one
normal (or main) and one emergency (or standby). Both are identical from the
Non-Return Valve (NRV) to the Pressure Reducing Valve (PRV). The accumulators
hold a quantity of fluid under pressure to be used when there is no supply (towing
for example). The NRV ensures that this fluid is not used by other circuits when
the pumps are off.
Notes:
-, -- --- -- -
-
-
I
1. $rC&ure transducers (to f/ighEEk gauges) are fittedto the brake lines
Pytween the brake contro! valve a n d t h e anti skid units, and between
the emergency brake control valve and'shuttle valves - but these are not
shiown for clarity. I I / I
2. !The brake control valve is;similar to/that shown in figure 40, with each foot
hbtor having its own reservoirTOh-some aircraft - the Tristar for example -
khk brake control valve is bperated b> cables from the rudde; bar so there i s
I I
no separate'foot motor hydraulic systerh for each foot on each rudder pedal
'(as
I
shorn' in the drawing).
I
I
I ,
1 '-
The pressure operated switch pl.o$dei_a warning on the flight deck should the
pressure drop to some low value. The pressure transducer and gauge provides
system supply pressure indication on the flight deck. The gauge could be a
moving coil, dc or ac ratiometer, or a synchro system . (See the book in this series
entitled Airframe Instruments).
The pressure reducing valve reduces pressure from say 3000psi to say 600psi. For
supply 1 this pressure goes to the brake control valve.
Lines to the brakes are often fitted with hydraulic fuses so if lines are ruptured
(due to runway debris damage etc) the system fluid will not be lost.
The brake control valve is operated by slave units which in turn are operated by
master cylinders on the rudder pedals. When a master cylinder is operated this
causes the slave unit to move - which in turn causes the brake control valve to
allow fluid pressure from supply 1 to the brakes. (For more detailed information
on Brakes, Autobrakes and Anti Skid systems refer to the book in this series
entitled Wheels, Tyres and Brakes).
rnoodull l A-1091
SUPPLY I SUPPLY 2
NRV
b ACCUMULATOR
LOW PRESSURE
PARKING BRAKE
SWITCH
PRESSURE
GAUGE
SHUULE VALVES
This supply then goes via the anti-skid unit to the brakes. The operation of both
rnaster cylinders will achieve in-line braking. The aircraft can be steered using
either the left or the right foot motor separately. (For normal operation large
aircraft are power steered through the nose wheel).
rnoodull l A-1092
In the system shown the emergency system by-passes the anti-skid valve, but
with most aircraft the standby system is an alternate system with a complete set
of duplicate components to the main system, but powered from another supply
circuit.
When auto brake is selected the brakes are selected ON automatically after wheel
spin-up to brake the aircraft quickly or slower depending on selection.
System 2 also stops the wheels rotating during retraction, so they are not
spinning in the wheel bay. This is automatic in operation. When 'up' selection of
the undercarriage is made fluid pressure causes the spring return jack to operate
and the brakes to come on. After a short interval the pressure in that part of the
'up' line is released - the jack spring returns the control valve to the off position
and the brakes are released. On modern aircraft this function is controlled by a
computer. Fluid pressure from supply 2 goes to the brakes via shuttle valves.
-. r- HYDRAULIC COMPONENTS
I /
This $art of the book describes vakious aircraft components of a general nature.
sever$ manufacturers produce'compone~tsand there are many different types i n
use. However, all components designed for one task rely upon the same basic
princi'ples although their appearance and
-
name may differ.
-
I '
Reservoirs
I
The actual size and shape will vary from aircraft to aircraft depending on capacity,
location etc. A simple unpressurised reservoir is shown in figure 19. Study the
details and note the level sighting glass, the filter, the vent relief valve, the return
and suction connections.
Figure 20 shows a pressurised type with a separator piston - note the contents
gauge system, the suction and return lines and the bleed and nitrogen
connections (not a common type). Figure 2 1 shows a pressurised type as fitted to
Airbus aircraft. Study the pressurisation system and make sure you know how it
works. Note the indications - reservoir quantity, oil temperature and
pressurisation pressure.
moodull l A-1093
VENT VALVE
\n
SIGHT GLASS
FILLER CAP
FILLER NECK
FILTER
CONNECTION
AFFLES to prevent
eturning fluid jetting
into air space
RETURN CONNECTION
the aircraft attitude
-
,
I
, --
1 \ I - - - -
-
I
I Fig. 19 UNPRESSU~SED
, RESERVOIR
' 1 I
Since it is not always possible to mount the reservoir above the pump, and to
ensure a positive supply of fluid to the pump, many reservoirs are pressurised.
The pressure (relatively low - about 30psi - but check your AMM) in the reservoir
also helps to reduce fluid frothing which could affect the operation of the system.
The method of pressurising varies, but may include the use of compressed gas
acting against a piston or diaphragm in the reservoir, or air from a compressor
stage of the jet engine (pneumatic system). If it is part of the aircraft's pneumatic
system the designer must ensure that there is no possibility of hydraulic fumes
entering the pneumatic supply to the cabin.
blank
rnoodull l A-1095
ANTI EMULSION
NEGATIVE G T
DRAIN VALVE
I .
.. ,, - I
, '
ENGINE DRIVEN 1
, 8
I
PUMP OVER HEAT
SENSOR
I ,
RAT PUMP
,,
, ,'
i /
-
!_ i
GROUND
CONNECTION
RESTRICTOR
RELIEF VALVE
rnoodull l A-1096
VENT flPE 70
ATMOSPHERE
I
Heat Exchangers, 1 1
I
In some systeys,heat exchange& ,areused to cool the hydraulic fluid from the
pumps. This extends the life of the fluid and the pumps. They are positioned in
the fuel tanks-so providing a heat sink from the hydraulic fluid to the fuel (also
warms the fuel and prevents the freezing of any water at altitude). Not fitted to all
aircraft.
- 34 -
They are normally situated in the idling line (case drain) between the pump and
the reservoir - so cooling the fluid returning to the reservoir and where more than
one supply circuit is used each will have a separate heat exchanger positioned in
a separate fuel tank.
They are positioned low in the tanks so should always be in fuel. If the fuel gets
to0 low the pumps can be still be operated provided the hydraulic oil temperature
does not get higher than that laid down in the AMM {eg 100°C (212°F))or after the
pump fault light comes on.
F'ilters
E;ASA requires that the hydraulic system should be adequately filtered. This
means that 'dirty' systems would have more filters fitted that 'clean' systems.
* -
HEAD
O-RING
-FILTER ELEMENT
O-RING
BOWL
moodull lA-10983
Before being put in the system the fluid passes through a fine filter in the
dispensing equipment and then through another filter a t the filling point (on some
reservoirs). The filter in the dispensing equipment is a micronic type, it's filtration
level being in microns; one micron = 0.00004in; a five micron filter therefore
would allow particles smaller than 0.0002in to pass unhindered.
The type of filter element varies depending on its position in the system and the
manufacturer.
The basic construction of all filters is similar with those in the pressure lines
being of more robust construction that those in the return lines. Elements are
made from:
(a) Felt
(b) Paper
(c) Wire gauge or cloth
(d) Wire wound spool
rp(e) /- Sintered metal -
- -
_
I /
QUESTION: What does 'sintered' mean? (5 mins)
r - - -
If the applied pressure is not too great then the fine particles bond
together in such a way as to allow small passages between them -
thus forming a filter element.
Sintered metal filter elements are cleaned using ultra-sonics and a counter flow of
fluid in a special cleaning rig.
Many filters are fitted with a clogging indicator. When the filter element becomes
blocked (or nearly so) a pressure differential is created (about 30psi - AP) in the
filter body to cause an indicator button to be pushed out. This is usually coloured
red and gives a visual indication that the filterlfilter element needs changing.
The indicator is kept out by a spring and may be pushed back (after the removal
of the transparent cover) once the filterlfilter element has been changed - or a s
directed by the AMM.
Provision is made that it will not operate until the fluid h a s attained it's correct
working temperature.
1 1
/
Fig. 25 F I ~ T E RCLQGGED INDICATOR
I
-'
, -
' ,'
-
-
i
--
- I ----- - - --
Pi11 filters must, by regulation, have provision for by-pass should there be any
chance that fluid starvation could occur if the elements became blocked. If the
filter element becomes blocked then a differential pressure (AP of about 60psi) will
cause the by-pass valve to open. This allows fluid through unfiltered - better this
than no fluid a t all. Of course, the clogged indicator will show.
When changing the filter element always change a n y seals a t the same time, and
always make sure that the replacement element is the same a s the one removed -
or an acceptable alternative as per the IPC (Illustrated Parts Catalogue).
INith some filters, as the bowl is lowered, internal valves close off the inlet and
outlet to the filter body thereby reducing the amount of fluid lose. Remember to
bleed the system after a filter change - a s per the AMM.
I I --
' I
Fig. 26 COMPONENT LOCATION - EXAMPLE1 AIRBUS
I I
A hand pump is included in some aircraft installations, for emergency use and for
ground servicing operations. Figure 27 illustrates a double-acting hand pump (ie
a pump which delivers fluid on each stroke).
As the piston moves upwards in the cylinder, fluid is drawn in through an NRV at
the inlet connection into the cylinder; a t the same time fluid above the piston is
discharged through a non-return valve in the outlet connection.
A s the piston moves downwards, the inlet NRV closes and the transfer NRV opens,
allowing fluid to flow through the piston. Since the volume below the piston is
larger than the volume above the piston, some of the fluid (about half) is
discharged through the outlet port. When pressure in the outlet line exceeds the
relief valve setting, discharged fluid is by-passed back to the pump inlet.
This a double acting single cylinder pump. Hand pumps are available from
manufacturers that are double cylinder and single acting.
OUTLET
PRESSURE
RELIEF VALVE
-- -- -- - -
- 1 -. M f INLET
I
Drawing f r o r n ' , 562
~~~ I
I ' Fig. 27 DOUBLE ACTING SINGLE CYLINDER HAND PUMP
I
.
I
ii
I
~ccurnul~tors \
-
,
I \ '
1 1 1
I
--
* ' Holds a reseye offluid Lnder pressure for- ~I H! e pumps
I
n are
- - not running. / I
x Allows instantaneous operation of systems.
J;
Assists the ACOV in operation.
PRESSURE GAUGE
CONNECTION
- -- -
May consist of a cylinder and floating piston or a spherical container and flexible
diaphragm.
QUESTION: Why charged with nitrogen and not air? After-all nitrogen is
expensive, air is more or less free. (5 mins)
ANSWER: Nitrogen does not support combustion - air does. Should a fine spray
of hydraulic fluid occur in a pressurised gas container a condition
similar to a diesel engine could be set up if the gas is air - and
combustion can occur.
Pumps
M:ost aircraft are fitted with multi-piston type hydraulic pumps, driven from the
engines. Other types of pumps, such as gear or vane positive displacement pumps
miay be found in some installations, but these normally do not provide sufficient
piressure - though flow rates are high. Pumps may be powered by:
t
ENGINE DRIVE
PUMP IDLING LlNE
- 41 -
rnoodull l A-1104
ENGINE DRIVEN PUMP
I IDLING LlNE OR
CASE DRAIN
These pumps deliver a fured quantity of fluid to the system at a particular rpm,
regardless of system requirements, and means must be provided for diverting
pump output when it is not required by the system.
- --- --- -
n-,-k ,-
W l l L cyyu
Af
"A
nt-.-~+nrn+
burrurruLL
+,A~,I-P
""Aurzr"
m,llfi-ni~tfnn
rrruro yAuc_u**
m11-n ie
y,ss**y -u ,A*-u..---u- ---
i l l ~ l ~ t in
~ fi0-11t-p
~ f p ~
--.3--- --. T----
'29 he
cylinder(blockand drive shaft rot4t.e together, and because of the angle between
the cyli<der block and shaft axes,!eachpiston moves into and out of it's cylinder
once ger; revolution.
1
1
I '
The stationary valve block has t y v ~ ~ @ ~ u ~ r eslots
n t i leading
al to the cylinder
block,'which are connected to the,fluid>irlet and outlet ports, and are 'arranged so
pistons draw fluid into the cylinders on the outward stroke, and push
to the system on the inward stroke.
CYLINDERBLOCK
BLOCK
UNIVERSAL JOINT
Another type of constant volume pump is illustrated in figure 33. In this pump
the cylinders are arranged radially around a crankshaft, so that when the
crankshaft is rotated, each piston moves in and out within it's cylinder once per
revolution.
rnoodull l A-11105
Fluid is drawn into the pump body and enters each cylinder through ducting in
tlhe cylinder block, whenever the associated piston moves to the bottom of its
stroke. A s it moves outwards into its cylinder, it covers the inlet port, and forces
fluid out of the top of the cylinder, past a delivery valve, to the pump outlet
connection. The drawing shows one piston for clarity but pumps have many
pistons with some having a dozen or more.
/DELIVERY VALVE
PRESSURE
-
/ 1
I Drawing f r o r n , ' ~562
~~
J?/ig. 33 CONSTANT
- XOLUME RADIAL PISTON PUMP /
I
- --
This type of pump is similar in construction to the fmed volume pump but the
cylinder block and drive shaft are co-axial and piston travel can be varied - so
varying the output. The pistons are attached to shoes which rotate against a
stationary yoke, and the angle between the yoke and cylinder block is varied to
increase or decrease pump stroke to suit system requirements.
When pressure in the system is low a s would be the case following selection of a
service, spring pressure causes the yoke to move to its maximum angle, and the
pistons are a t full stroke, delivering maximum output to the system.
When the selected system h a s completed its operation, pressure builds u p in the
supply line and under the control piston. This moves the yoke to the minimum
stroke position. In this position a small flow through the pump is maintained
(liom inlet to case drain) to lubricate the working parts, overcome internal leakage
and dissipate heat.
On some pumps a solenoid-operated depressurising valve is used to block delivery
to the system, and to off-load the pump.
These are fitted between pressure lines and return lines. They are designed to
relieve pressure should it build u p above normal working pressure. They are not
designed to operate continuously as this would keep the pump 'on load'. Pressure
relief valves are usually a spring-loaded ball or a spring-loaded plate - often
adjustable - but by the manufacturer only or in the hydraulic overhaul bay.
- 44 -
rnoodull lA-1107
Fig. 35 ENGINE DRIVEN PUMP LOCATION - EXAMPLE B 7 6 7
ADJUSTER
RESERVOIR
SYSTEM PRESSURE
\
->
I
l~rawingfrom CAP 562
Fig. 36 PRESSURE,' RELIEF VALVE
I
I
I
QUEST1ON:These valves often all look alike but are set by the mahufacturer to
operate a t different pressures depending on the system they are
designed for. How would you know which is the correct one for a
particular system and location? (1 min)
ANSWER: By reference to the description and part number, (on the component),
the AMM (aircraft maintenance manual), the IPC (illustrated parts
catalogue) and the EASA form 1.
Fitted to systems employing a constant volume pump, to provide the pump with
an idling circuit when no services have been selected. An accumulator is
essential when an ACOV is fitted, since any slight leakage internally or externally
would result in continuous operation of the ACOV (hammering).
QUESTION: Why would an ACOV 'hammer' if a n accumulator was not fitted? (10
rnins)
I I
When cut-in and on-load, the pump would take a fraction of a second
to build u p the pressure from 2500psi to 3000psi (as the volume
I '
required is so small). TEEs the ACOV would cut back out again - in a
fraction of a second; This cycle,would be repeated very quickly
,
causing ACOV hammering. The accumulator gives the system some
1
'resilience' it takes time to build the pressure u p - and time to loose it
I )
so the ACOV may cycle, say once every 30 minutes or so instead of
every second or so2_
-
When a service has been selected and the pump is delivering fluid to the system,
the NRV is open and equal pressure is applied to the top of the poppet valve and
the bottom of the piston. The force of the spring combined with the pressure on
the poppet valve is greater than the force on the piston, so the valve is closed and
the return line to the reservoir is shut.
When the service selected has completed it's travel and fluid is no longer required
for the systems, the pressure applied to the piston is sufficient to lift the poppet
valve off its seat. This results in a sudden drop in pressure on the pump side of
the valve which snaps the poppet valve open and the NRV closed.
Pressure in the idling line drops to a low value and the load on the pump is
removed. Pressure in the system is maintained by the accumulator until further
selection is made - when pressure drops, and the pressure on the cut-out piston
becomes less than the spring force, the poppet valve closes and pump output is
again directed to the system through the NRV.
POPPET VALVE
PUMP SUPPLY -
NON-RETURN VALVE
Fig. 37 ACOV
1 -- I
!
The valve,will open to allow fluidlto-the secondary services if noI?nal sudply is
I
SECONDARY
SERVICES
PRESSURE
INLET PRIMARY
SERVICES
A. priority valve may be fitted immediately after the power circuit with one
pressure line supplying all the secondary services and another pressure line
supplying all the primary services.
rnoodull l A-I 1 10
On some aircraft the priority valve is fitted in front of each secondary circuit.
Each secondary circuit will be connected to the secondary services port of the
valve and the primary services port will be blanked off.
Fluid enters the inlet port, and flows through the valve to the low pressure sub-
system. When the fluid pressure exceeds the spring-loading on the valve, the valve
is lifted and gradually covers the inlet port until sub-system pressure reaches the
specified value - when the supply is shut-off. If sub-system pressure increases for
any reason, the valve is lifted further
--- and uncovers the return port to relieve
-
- -
excess pressure. - -
RETURN
PRESSURE INLET
_,LOW PRESSURE
SUBSYSTEM
This valve is quite 'a box of tricks' so you will need to take it slowly. They vary
from aircraft to aircraft so you should not need to commit the details to memory -
but you should understand the principles on how it works.
If the brake control on your aircraft is different and you understand it then fine -
don't bother with this one. But either way the CAA will expect you to know how
the brakes are operated on a large civil aircraft.
- 48 -
rnoodull l A ~ 1 1 1 1
This brake control valve is essentially a variable pressure valve, which controls
pressure in the brake system according to the position of the pilot's brake pedals
or hand brake lever. The valve usually contains four elements, one pair for the
brakes on each side of the aircraft, to provide duplicated control. Figure 40
illustrates a single element, in this case operated by a slave servo from the brake
pedal master cylinder.
When either pilot's brake pedal master cylinder pedal on the appropriate side is
depressed, or the hand brake is operated, the footbrake servo applies a force to
the linkage on the control valve, which, via the lever assembly and plunger,
presses down the exhaust valve cap. This action initially closes the gap between
the exhaust valve cap and the exhaust valve seat, then moves the cradle down to
open the inlet valve and direct fluid to the brakes.
Pressure builds up in the brakes and under the valve until it is sufficient, assisted
by the spring, to overcome the inlet pressure and the force exerted by the plunger
fo'rce.This pushes the whole assembly upwards to close the inlet valve and the
increase in pressure to the brakes stops.
An increase in the load applied to the valve plunger will be balanced by increased
delivery pressure, and a decrease in the load applied will be balanced by relief of
delivery pressure past the exhaust valve cap to exhaust. In this way the pressure
applied to the brakes is proportional to brake pedal pressure.
When the brake pedals are released, the cradle moves to close off the inlet port,
the exhaust valve cap lifts, and exhausts the pressure from the brakes to the
reservoir.
Non-Return Valves
The NRV or check valve or one way valve is a common device used to control the
flow of fluid. It permits full flow in one direction, but blocks flow in the opposite
direction. Simple ball-type non-return valves are common but designs may vary.
When a non-return valve is used a s a separate component, the direction of flow is
indicated by an arrow moulded on the casing, in order to prevent incorrect
installation. The arrow points in the direction of flow.
Hydraulic Fuse
The valve will permit normal flow, but if the flow rate rises akjove a predetermined
level t h e valve will close its outlet linepreventing further flow. Often fitted to wheel
brakelines due to the high probability of damage (and leaks) to from
flying h n w a y or @re debris. On some airc+aft, fuses are fitted a t locations
throughout the,/hydraulic system. 1
1
CHAMBER.
I)
During normal operation the pressure differential that exists either side of the
spring-loaded piston is minimal therefore the piston remains a t the full-flow
position a n d an uninterrupted supply goes to the brakes. If an excessive flow rate
oc:curs (due to a large leak), the pressure difference on top of the piston through
the metered orifice will be sufficient to push the piston down and block the exit
side of the fuse. It will remain closed even if the brake pedals are released - as
reservoir pressure will hold it closed. The fuse will need to be bled and reset - with
the brakes off.
IIblPORTANT. Always carry out a full brake/system test after fuse operation/
bleeding to check for correct re-setting.
7 -
Restrictor valves I ---
I I
\ I
I
-
QUESTION: Why are flaps and landing gear likely to move too fast? (2 mins)
ANSWER: The landing gear will tend to fall under its own weight and the
flaps will tend to be blown u p by the airflow (if jack operated).
rnoodull lA_1114
It is important to note that while they restrict the flow of fluid, the actual flow rate
through the valve will be related to delivery rate, delivery pressure and the design
of the valve.
Selector Valves
These may be manually or electrically operated, and can be of the four-way type
(eg, where flap operation would require an intermediate selection), or of the two-
way type - where no intermediate positions of a service are required(eg landing
gear retraction). The purpose of a selector is to direct fluid to the appropriate side
of the actuator/jack/hydraulic motor, and to provide a return path for fluid
displaced from the opposite side of that actuator.
A two-way selector valve connects the pressure and return lines to alternate sides
of the actuator, without a neutral position. Selectors in open-centre systems will
trap fluid (hydraulic lock) in the actuators while providing an idling circuit for the
pumpTSFme manually ~ p e r a t e ~ v d v are
e s shown in figure 43.
I '
ANSWER: Negative feed-back. Where the output tries to cancel the input.
When the selector valve is located a t a position remote from the crew
compartment, and to eliminate the need for extensive mechanical linkage the
valve is normally operated electrically - or at least initiated electrically - the actual
operation is done hydraulically.
The selector shown in figure 44 is a typical electrically initiated (28V dc) two-way
valve, which may be used, for example, for operation of the landing gear.
With the solenoid de-energised, the pilot valve is spring loaded against the return
seat, and fluid from the system passes to both sides of the slide valve.
rnoodull lA-1115
JACK
JACK JACK
SLIDE VALVE
I
P
ROTARY VALVES t t i 6
JACK JACK P JACK
SLIDE PISTON
Fig.
1
' I I
/
1
~~
I I I
i
I
moves-to the left and fluid passes to the leftside of the actuator! F;luid from the
opposite side of the actuator passes thrmgh the selector to 'the return line.
With the solenoid energised, the pilot valve is held against the pressure seat and
supply pressure acts on the left-hand side of the slide valve only, the right-hand
side being open to return. The slide valve moves to the right (as shown), and
directs fluid to move the actuator in the opposite direction. The other side of the
actuator being open to return - via the valve.
With one solenoid operated (solenoid 'B' ) the supply to tha.t side of the valve is
shut off and the pressure that was there is allowed to return to the reservoir.
With pressure to only one side of the slide valve the slide valve will move over to
allow fluid to one side of the jack. The other side of the jack is allowed to return
via the other port.
SUPPLY
I b3- SOLENOID
I
I
: ~ r a w i n gfrom CAP562
Fig. 44 ELECTRICALLY INITIATED TWO-WAY
! SELECTOR ,VALVE
I I I
I
,I--
'
'
In figure 45 the effective area oflthe slide valve piston on the left is greater than
that1 of thc sght.'This is due to the fact that the annulus slide is away from it's
- ---- p-
body stops but resting on the slide stops. Thus the slide valve and annulus slide
move to the right until the annulus slide rests on the body stops - the effective
area then becomes equal and the slide valve stops - in the middle.
blank
TERMINAL BLOCK EARTH RETURN
I
I
t
SUPPLY I
RETURN
ANNULUS SLIDE
SLIDE
- 1
' ,
i
I SUPPLY
\,
I
e RETURN
J \
TO JACK FROM JACK
rnoodull lA-1118
Fluid Jettison Valve
Fitted in the emergency gas system this valve permits up line fluid to be dumped
overboard on emergency down selection.
On selection of 'emergency down', gas pressure is fed into the base of the valve
(figure 46) to act on the piston to unseat the ball valve. UP line fluid can now vent
to atmosphere. When gas pressure is released the piston will be moved down by
it's spring and the ball valve will automatically reseat.
FLUID FLOW
--
I
JETTISON
FLUID
GAS -
, PRESSU
I
I ,
I Drawing from CAP 562
Fig. 46 !FLUID JETTISON VALVE
I
-- - 1
These are often used in landing gear and brake systems, to enable an emergency
or alternate system to operate the same actuators as the normal system. During
normal operation, fluid flow is provided from the normal system to the service and
the emergency linelalternate supply is blocked.
TO SERVICE
A
ALTERNATIVE
OR __C
I NORMAL
EMERGENCY
SUPPLY 1 SUPPLY
Slome shuttle valves have an electrical connection to them to monitor the normal
supply pressure or to indicate piston position. This data being sent to control
computers.
RETURN FLUID
Sequence Valves
Sequence valves are often fitted in landing gear circuits to ensure correct
sequencing of the landing gear jacks and door jacks. Examples of mechanically
operated and hydraulically operated sequence valves are shown in figure 48.
Slequence valves ensure that the landing gear does not extend until the doors are
open, and that the landing gear is retracted before the doors close.
Completion of the initial movement of one of the actuators results in part of the
rr~echanismcontacting the plunger of the mechanical sequence valve, moving the
piston and allowing fluid to flow to the next actuator.
moodull 1A-1120
Modulators
BRAKE TO
PRESSURE BRAKES
ORIFICE PISTON
, /--
---
~ u r i n kibitid operation of the biakes, the. piston is forced down the cylinder
against gpring pressure, and the 6rakes are applied. Subsequent fluid feed to the
brakes, necessitated by anti-skid Gnit operation, is through the restricting orifice
and is limited. This limited flow allows the anti-skid unit to completely release the
brakes when necessaty, and coLservesqain system pressure. When the brake
control valve is released, the pis').onreturns to its original position under the
influence of the spring and the returning fluid from the brakes.
VALVE SEAT
OUT
If inlet pressure rises, or demand increases, the pressure differential across the
v,alve head also increases, and moves the valve to the left (in the drawing) to
reduce the size of the aperture and maintain a constant flow.
The spring loading is increased by the valve movement, and again balances the
pressure drop. Similarly, if inlet pressure drops or demand decreases, the valve
takes u p a new position, to the right, so a s to maintain a constant flow.
Hydraulic J a c k s or Actuators
,--
/
1
Drawing from CAP 562
Fig. 51 TYPES OF JACK
Jacks are the main component in a hydraulic system for the conversion of
hydraulic power to mechanical power. In one form or another they are found in
landing gear circuits, flap circuits, spoiler circuits, powered flying control units,
nose wheel steering circuits etc.
moodull l A-1122
There are two basic types in use depending on the requirements of the system
they actuate. The most common is the unequal area type which is adequate for
most requirements. However, due to the ram, piston area on one side is less than
on the other and t h u s extension and retraction forces (and speeds) will differ.
Where it is necessary to generate the same force or same speed in both directions
an equal area jack is used. In this case the ram on both sides of the piston
reduces both areas by the same amount. The type of jack will also dictate the
speed of operation. Given the same fluid supply in each case an unequal area jack
will move in faster than it will move out. With an equal area jack it's speed of
operation is the same in both directions.
QUESTION: Which one of the jacks shown in figure 5 1 would be fitted in a power
steering circuit? (5 rnins)
ANSWER: One double acting equal area jack - similar to the A320 or two
!, - 1 double acting un@al Zea jacks - similar to the B747. I
QUES~ION
Which
: way should the unequal area jack move to retract the
I landing gear ideally? (3mins)
I
A N S W ~ R :It should move out or to the right in the previous drawing. This
1 1 will mean that it uspsits largest area and provide its greatest force.
, SPRING
RESTRICTOR
-
VARIABLE
RESTRICTOR
--\-
To relieve slow pressure rises due to thermal expansion of the fluid a thermal
relief valve is fitted between the pressure line it is to protect and a return line.
Similar in principle to a pressure relief valve but it incorporates a restrictor which
ensures that when it opens it will relieve only some of the pressure. Works on
pressure only.
Throttling Valve
A specialised restrictor valve similar to the flow control valve which automatically
regulates the flow-rate in inverse proportion to supply pressure to maintain a
constant speed of component operation. These may be one-way or two-way.
Figure 54 shows a two-way valve in operation. When too much fluid tries to flow
through the valve the piston is moved so that the metering needle enters the
outlet orifice, thus restricting the fluid flow. The valve is so designed that the
o-utlet fluid flow rates are within the normal operating parameters.
SPRING
,
I
' t ;
HIGH FLUID '
,_F_L_OWRATE
- /
~ r a w i n ~ f f r 562
o 5 ~ ~ ~
Fig. 54 THROTTLING VALVE
I n some cases both types of indication are provided, the direct reading gauge
being fitted in the hydraulic equipment bay, adjacent to the relay. It transits fluid
pressure but not fluid flow.
During normal operation the piston acts as a separator, moving within a limited
amount to transmit fluid pressure from the supply side to the gauge side. If a leak
develops on the gauge side, the piston moves to the gauge end of the cylinder, and
the valve seats in the cylinder head, thus preventing leakage from the system
(there will be a small leak from the gauge line, but only a few drops).
TO
GAUGE
PIS~ON VALVE
7 I-
-
-
Quick:Disconnect Couplings ,
I I
I I
In positions where it is n e c e s s h to frequently disconnect a coupling for servicing
purposes, a self-sealing, quick disconnect coupling is fitted. The coupling enables
the line to be disconnected without-loss of fluid (without the need for subsequent
bleeding) a n d they be bayonet or screw type.
' I 1 ,
I 1
Pressure Release Valves
I , I
\ --
~ i t t e d t oen-able pressure to be released from the system for servicing purposes.
The valves are manually operated, and consist of a valve body with a n inlet and
outlet port, the passage between the two being blocked by a spring-loaded valve.
Operation of an external lever opens the valve against spring pressure, and allows
fluid to flow from the pressure line back to the reservoir.
Drain cocks are simple manually operated spherical valves, a n d are located in t h e
hydraulics bay a t the lowest point in the system. They are marked to indicate
direction of flow, and are used to drain the system in order to replace the fluid, or
in some systems to change certain components. A sampling valve allows fluid to
be taken for analysis a t periods specified in the maintenance schedule or at times
when hydraulic fluid contamination is suspect.
- 62 -
rnoodull l A-1125
Fire Shut-Off Valve (SOV)
E;lectrically operated and mounted between each reservoir m d each of the engine-
driven pumps (within a fire zone). Closed when the flight deck fire handle is
operated.
SAMPLING
AMPLING V A L V E
II
--- - \*-
FLUID SAMPLING
' I
I 1
1 1
These make it poidible to cut-offltqe supply:offluid quickly
seconds) in the event of a fire in the enginej1Theshut-off valve's are normally
controlled~fr~m/the hydraulic panel\by th,e/PUMPS ON-DUMP- HUT
VALVES
switch&. The shut-off valves c&e when-the associated swiche$-are placed in
the SHUT VALVES position. When the switches are a t either of the other two
positions, the valves are open.
- 63 -
rnoodull lA-1126
In the event of an engine fire, the fire control handle is pulled and the fire shut-off
valve will close irrespective of the PUMPS control selector position.
Hydraulic Motors
This converts hydraulic power into rotary motion, usually by the swashplate
principle. These motors which are reversible, may be operated continuously,
intermittently, or stalled without damage. Used for powering generators (rare) and
in systems such as spoilers, flaps, etc. The speed of the motor depends on the
fluid supply rate or the angle of the swash-plate and the torque it can produce
depends on the supply pressure.
S W BEARINGS
' I I
I VALVE PLAT; INLET SLOT
~ /
Pressure fluid enters the motor through a valve block (figure 58). It is directed to
the individual cylinder bores through a valve plate. The non-rotating valve plate
provides the timing for the motor.
Pressure builds u p in the cylinder bores until the resulting force on the drive
shaft overcomes the resisting torque. The pressure of the fluid is transmitted from
the piston rods to the drive shaft, overcoming the torque resistance of the load
connected to the drive shaft. Fluid under pressure enters via the inlet slot to those
pistons on their outward movement. The pressure exerted on the piston will push
it out - but it can only go out if it moves up (in the drawing). This it does, and a t
the same time moves round. This causes the cylinder block to rotate in the
direction shown (figure 58).
Tlhe universal link keeps the drive shaft and cylinder block in alignment since the
piston rods have ball joints on both ends. The drive between the cylinder block
and the drive shaft is maintained by the universal link. The link however, does
not transmit load torque. Each piston rod has pressure-lubricated ball joints at
both the piston and drive shaft ends.
1. Accumulators.
2. Electrically driven pumps - ac and dc.
3. Duplicate/ triplicate systems.
I 4. Duplicate/triplicate components - PFCUs, yaw dampers, A/P servos.
' 5. Power transfer unitSfrorone system to another;----
6. # Manual reversion (PFCUS). , \ \ I -
7. Gravity freefall ( U J Cdown). !
8. Gas operation. II
9~. Ram air turbines (RAT). ~1 II
Ill. Separate system with Kd~-driven pump (U/C down on some aircraft).
1
\ I I
I
I I ' I
A RAT System
/
I
I
-
1 I j
The RAT-^&<^^ stowed in the Kottom
-
L-
P
-
R A M AIR TURBINE
RAH A
AS
1
Fig. 60 HYDWULIc RAM AIR TURBINE (HYRAT)
-,
-
!
I
When the RAT is released the ejection jack extends under it's spring pressure to
thrust the RAT into the airstream. The latter stage of the jack extension is
retarded by the hydraulic damping device to avoid high impact at full extension of
the unit. A down-locking pin secures the RAT in the extended position.
The doors are mechanically opened and locked by the RAT movement.
With the RAT in the stowed position the test selector is set to provide a permanent
supply of warming fluid. This maintains the power pump and the gerotor pump
(an Airbus term) at the correct operational temperature. The flow is controlled
within the control module and by the flow-sensitive valve in the leg.
- 66 -
rnoodull l A-1129
A:j soon as the RAT is down and locked the turbine is simultaneously unlocked by
withdrawal of the locking rod and immediately commences to rotate due to the
airflow. After the momentary off-loading effect provided by the flow sensitive valve,
th~epower pump operates to supply full pressure to the yellow system. Hydraulic
pressure supplied by the gerotor pump for operation of the speed governing
mechanism passes via the turbine shaft sleeve assembly into the piston valve.
A s the turbine rotates, centrifugal force causes the governor weights to pivot
outwards and move the piston valve against it's spring pressure. This allows high
pressure fluid to pass through ports in the sleeve and shaft and flow to the
annular chamber.
Here the pressure acts on the cylinder which is moved forward against it's spring,
turning the blades toward the fine pitch position. Low pressure fluid, displaced
from the space forward of the cylinder, passes via the cylinder guide and central
ducts of the piston valve and drive shaft to return to the gerotor pump.
Figure 6 1 shows the RAT system schematic. There is no need to remember the
details, but you should be able to follow the general principles.
Rat Test
It is possible to test the RAT pump --performance on the ground. A special test
selector allows the pump to be ulsed as a motor to drive the propeuer.
I I
INERTIAL
EFFECT
MI\\\.\\\\\\\\\\
TO YELLOW SYSTEM
To carry out the test the Yellow hydraulic ground supply must be connected and
aircraft electrical power on. The M T leg must be extended and locked down. The
area must be cleared with position warnings posted and the area roped off.
Reset Procedure
1.
2.
-
I Reset the control hrmdle. -
Check that the filter cJogging igdicator is 1N'.
I
- -- -
\
I '
Set the blades perpendicular to allow the blade locking pin to engage
3. i
the spline. I
-
i - -' '
/ I
- - 1
THE POWER PACK
Light aircraft may be fitted with a power-pack which contains all the hydraulic
components including pumps, valves etc to operate the services. The pump is
usually powered by an electric motor which is caused to switch off when normal
maximum system pressure is reached. It comes on automatically when system
pressure is required (figure 63).
When the selector lever is operated the pressure from the accumulator starts to
move the actuator. A s the accumulator ram moves up, the switch operating collar
moves away from the motor switch and the pump commences it's pumping cycle.
The actuator will extend until full travel is reached. Further pump action will
recharge the accumulator until the fully charged position is reached and the
switch-operating collar will operate the motor switch and stop the pump.
To prdv&ntleakage of fluid past pibtons, &ston rods, etc, special seals are fitted.
The matbrial used depends on the type of fluid used in the system, while the
shape,of a seql is governed by the pressure of the fluid and the purpose of the
seal.
---- - --
- -
Hydraulic seals are made of natural rubber, synthetic rubber, or other synthetic
material (check the earlier pages in this book on hydraulic fluids). Modern seals
are made to meet the fluid specification (MIL SPEC or local o r national
specifications) to cope with the temperature range, operating conditions and fluid
types.
Care must be taken when replacing seals as they can easily be damaged. Special
tools are provided for there removal/fitment.
Square Section Seal. This provides sealing in both directions and can be used a s a
piston ring seal. It is either located in a square groove in the piston head or
supported by Tufnol rings on either side.
rnoodull lA-1133
Fig. 64 SQUARE SECTION SEAL
'O' Section Seal. This seal is used to provide a fluid tight joint for contact surfaces
where no movement takes place (ie between the mating faces of two halves of a
component where a fluid tight joint i s required), especially where the shape of the
joint is irregular. If used on moving surfaces with pressures above 1500psi they
should be backed with backing rings to prevent distortion.
-
:
- Fig. 65 - -
~ ~ O ' SEAL\ I---
R O U N D OSECTION
! \
I I
I '
~ o n d e dSeal.
- Consists of a m e t 4 washer with n rubber seal bonded to its inner
surface!, the rubber being slightly t h i c k e r h a h the metal. It is u ~ u d l fitted
y with a
hollow bdlt that is torque loaded and iS used for sealing end c k p , banjo/unions,
e1.c where no movement takes p l a c e 7 ' \ a
! . ', I
-
I
I
- - - I
i
RUBBER
METAL
Fig. 66 BONDED SEAL
Wiper
- Ring/Scrapper Ring. This is not a seal as such, but fitted to prevent
dirtldebris from entering the seal assembly on a piston ram, undercarriage oleo
leg etc.
/
WIPER EDGE
Fig. 67 WIPER RING
- 71 -
SOFT RUBBER
@
Fig. 68 DUPLEX SEAL
HARD RUBBER
Chevron Seal. If used singly will withstand pressure in one direction only. If used
backed as a pair will withstand pressures in both directions.
The drawing shows a single chevron seal designed to withstand pressure in the
direction-shown. It is normally-supported by back-up spacers and spreader
!
CHEVRON SEAL,
@'""'"
packingipieces between it and the component.
0" 'A'""
i
I
I
t
I PRESSURE DIRECTION
Fig. 69 CHEVRON SEAL
-. - - -
'V' Ring/'UYRing Seals. Similar to the chevron seal, though the W' ring seal has a
shape similar to a U' rather than a V'. Normally used without backing pieces and
are fitted singly.
PIPELINES
rnoodull l A-11:35
Hydraulic components are identified by means of self-adhesive placards showing
the component number a s given on the hydraulic system general drawing. A s a
rule, numbers beginning with 1, 2 or 3 are used for Green, Blue and Yellow
system components respectively.
1 1063
SELF ADHESIVE
IDENTIFICATION LABEL
~
I
- -
1 --
I
I FLIGHT-DECK,INDICATIONS I
1
i
\
\ \ 1
These are covered in more detailini the book on instruments in this module but
below i's a generdl outline of instrumentation
I '
as specifically applied to hydraulic
systemk. , 1 I I 1
-- I
- - -
]For details of the principle of operation of these instruments systems you should
]refer to the book in this series entitled Airframe Instruments.
The indication systems which follow are based on the Airbus family of aircraft.
These can be considered as typical for a large modern aircraft.
SYSTEM
BLUE I GREEN
SYSTEM
I YELLOW
SYSEM
I
SELECTORS
I
1
I
I
I
INDICATION
I
I
1 I
I 1
1 I
' !
1 I
~ i 7
&1 HYDRAULIC1 SYSTEM CONTROL PANEL - A300
-
- -- - --
The hydraulic systems are controlled and monitored from t h e flight declC
hydraulics panel. The panel arrangement represents the fluid flow from the timks
to the p u m p s and high-pressure delivery to the systems.
The control panel shown (figure 71) is vertically divided into three sections, one
for each of the three independent systems. The panel shows pressures for all
three systems for reservoir pressurisation and system supply pressure.
The panel allows for operation of: dumplshut-off valves for t h e EDPs (shuts the
fire-valve a n d de-activates the EDP); electrically operated pumps and the power
transfer unit.
rnoodull l A-1137
@ Reservoir LO AIR PRESS indicatian :
@ Rcscruor OVHl indication :
YELLOW
@ FLRE VALVE indicrtion :
LO A I R > L O AIR LO A I R
@ PTU control :
PRESS PRESS PRESS
@ ENG PUMPS control and low prcrue i n d c a h .
OVHT L OVHT
T A T t I9'C C.W.60300 KG
SAT t 1B'C C.G.ZB.1 %
/ - -
-- -
\
r-
1-
Fig. 72 HYD&LICS CRT PAGE OF THE A320
I '
I
I
1
1
~
I
I
'
I
2
Figure ;72 shows an example of f l & h t d e c k , ~ display
~ ~ of thd hydraulic system of
the A320. It is a colour display and gives,details such as: pressure indications;
low pressure warnings; fire-valvdlpbsitions;,oyerheat etc. It is belectedusing the
page selekor panel in the flight deck and i i p a r t of the ECAM1(~lectronic
Centraliskd Aircraft Monitor) system of the aircraft.
I 1
1
1 i 1 1
Note that in fi&re 73 the OR gate in-the ldgiL circuit means that a warning will be
given if any one of the following~occurs: A
This is a float and arm mechanism which drives a synchro-transmitter shaft via a
magnetic damper which rninimises the transmission of the float oscillations to the
synchro-transmitter.
PL direct reading gauge pointer is mounted on the opposite end of the synchro-
transmitter shaft which allows the fluid level to be read a t the reservoir location
without power being on. The electrical output of the synchro is sent to the flight
dleck gauges/ computer.
Fig. 73- WARNING LOGIC
-
\ / -
I 1 \ '
The LEVEL LO warning light is activated by a switch which is closed by a cam
mounted o n the synchro when fluid level gets low - about 5 1 (1.3U S gallons).
I
I ! I /
Figure 714 shows the wiring circuit forthe level indicator s y s t e d - note the lines to
I I
the repeater gauge (for the aircrpi servicing panel). The low level switch grounds
the LEVEL LO light circuit and thk HYDRAU inputs the MWS.
1 I I
I I 1 I
The pde$s-to-test caption light slvitch, grounds the light circuit to test the lamp
a n d [to activatk the master warning.
-
-
p p
indl TO REpE,iiAuGE
26V GUANTITY
AC OUANT.lNDICATOR TPANSMITTER
Manifolds
& Tanks LOW LEVEL
SWITCH
MWS
28V
DC
- 76 -
A high temperature warning circuit is provided for each of the three systems
T:he overheat sensor consists of one arm of a resistor bridge. The bridge output
signals are amplified and when the temperature gets too high, (85°C [185"F])it
triggers a transistor which grounds the TEMP HI, switching it on together with a
warning chime.
Pressing the TEMP HI light caption unbalances the resistor bridge to simulate a
high temperature.
The reservoir low-pressure switch grounds the AIR PRESS LO light circuit to put
the warning light on in the flight deck.
The amber LO AIR PRES light illuminates when the pressure drops to about 1.5
bar (22psi).
- - MAINTENANCE
--
, I -
All maintenance is carried out 4 accordance with the AMM q d ,the maintenance
schedule! If it is routine maintenlance then thk specified tasks!T e carded out a t
tlie times specified in the approvedl maintenance schedule. If it is non-planned
maintenance such as fault rectification-tlien
, it is carried out followinglp~ocedures
1 - -
-
published in the AMM. -
i 1
',
i /
C:leanliness is of tQe utmost importjance. The filters fitted in the 'Arcraft system
I
will normally protect the components from the effects of partidle contamination,
I /
blut it is important that any ground equip,ment used for servicing purposes is kept
scrupulously clean, and that thefluidis filtered to a similarl-stddard.
--- - --
C:ontamination from other fluids must also be avoided, and provision is usually
made for taking fluid samples.
When the system is topped-up from a can, any unused fluid in the can should be
discarded or poured into a dispensing rig - unsealed cans with fluid in them
should never be left (the fluid could become contaminated and be used in an
stircraft system at a later date).
- 77 -
rnoodull l A-1140
Sampling
Samples of the system fluid should be taken at the periods specified in the
approved Maintenance Schedule, and whenever contamination is suspected.
If a fluid sampling kit is available it should be used strictly in accordance with the
manufacturer's instructions, but if such a kit is not available, the sample should
be sent to a laboratory for examination.
The bottle into which the fluid is drained must be scrupulously clean, to avoid
any contamination that may be already present in the sample. The bottle should
be washed with soap and water to give a clean, bright finish, rinsed in clean
water, then in filtered alcohol, and dried with clean dry air.
It is usually recommended that plastic sheet is interposed between the bottle and
the cap, to prevent the formation of loose particles when the cap is screwed on.
The aition which is necessary to d&e following the testing of a sample of fluid,
will ddpend on the degree of contahination found. The parameters to be tested
are - acidity, spkcific gravity, viscosity, water 'content, and particle contamination,
and acceptable values are specified in the appropriate AMM.
- - -
- --
Flushing
When it is necessary to flush the main system, the filters should be changed and
the fluid should be circulated by operating the largest hydraulic jack a number of
times. Either an auxiliary pump, or an external hydraulic test rig may be used for
flushing, but, if an auxiliary pump is used, it is recommended that it is
subsequently removed and inspected for possible damage.
Make sure that all driven pumps are configured so that they cannot be operated
before commencing draining. If any of them were to be run dry (ie without fluid)
then serious damage would occur.
The hydraulic system should be made electrically safe (by tripping off circuit-
breakers or the removal of fuses, as appropriate). The hydraulic pressure should
be released by operating one of the services or operating the pressure release
valve, and the air pressure should be released from the accumulators and
\ reservoir. The reservoir filler cap-should
- be removed, and fluid should be drained
into a cleari
,
container of suitable capas@;
- I-
by means of the Lystem drain cock.
I 1
I ' ' ,/ I
Some circuits/components will leak internally - from the pressure line to return.
This applies to those components where valving employs sliding members that
rely on metal-to-metal contact for sealing purposes such as PFCUs.
The leak-rate can be checked and if it is found to be higher than that laid down in
the manual then the source of the leak must be found and the component
replaced; and if a n external leak, it must be found and rectified - and the leak-
rate re-checked.
To check for leaks connect a hydraulic ground power unit equipped with a
sensitive flowmeter and pressurise the circuit to the correct pressure a s per the
fiMM. Set the PFCU servo control selector to OFF to isolate the flight controls.
moodull l A-1142
Close all shut-of valves - note the fluid flow.
Open the centre shut-off valve to pressurise the tail section of the aircraft. This
will pressurise the following:
* The rudder and elevator PFCUs.
-k
The tailplane trim (horizontal stabiliser trim).
* The yaw damper, etc.
Note the leak-rate flow and compare it to the nominal rate stated in the AMM.
To test the wing areas successively open the right-hand and left-hand shut-off
valves and compare the two leak-rate flows to the laid down in the AMM.
\
-- -
Some aircraft are equipped with an internal leak management system which is
used to detect abnormal internal leaks in the PFCUs.
rnoodull l A-1143
System Filling
Filling may be carried out through an open reservoir filler neck, or through a
priming connection in the ground servicing bay using an external priming rig, or
through a common self sealing coupling with a selector valve to fill anyone of
several reservoirs.
Bleeding
To ensure correct operation of the system all air must be removed from the
pipelines and components. Some components are bled by slackening the pipe
connections allowing fluid to escape then retightening. Some components are
fitted with bleed valves/nipples, and others are purged by operating the service
-
The airkraft should be jacked in accordance with the AMM an;d the accbmulators
shouldbe charged with nitrogen to-the c6rf6ct pressure. Ground- electric& power
shouldlbe connected and the apprdprixe fluid level and pump overheat warning
lzunps should be tested.
I I '
I I 1
I I '
I n general the fohowing points sdould be observed, but always refer to the AMM:
/ /
I
L -/ _- i
- 1. -- Use-the aircraft e16ctrically-driven pump or hand pump.
2. Keep the reservoir topped u p and pressurised if of this type.
3. Start bleeding from the lowest and most distant point in the system -
if all the system h a s to be bled.
4. Always bleed from the small volume end of the jack - ie the end that
the piston is at.
5. Use a clear plastic hose placed over the bleed nipple with the free end
immersed in a glass jar half filled with the same fluid.
6. Using the hand pump slacken the bleed nipple until an air-free-flow
of fluid is obtained from the end of the hose.
7. Tighten the nipple and allow the piston to be pumped to the other end
of the jack. (The jack may have to be disconnected from the
component it moves to allow access).
8. Bleed this end of the jack as in 5 to 7 above, and reconnect jack if
necessary.
9. Carry out this procedure on all jacks/ actuators/ bleed connections in
the system or circuit affected.
10. Place components - landing gear, flaps etc in correct position and
top-up reservoir to correct level.
NOTE. The fluid obtained from the bleeding process should not be re-used.
----
landing gear down and all other services in or u p (ie flaps up, spoilers
- - -
I- in etc). ,
1 i \
Note. If excessive amount of flulidis required to top-up to the correct level then
investigate the reasons why - add rectify.
I
-
-- -
Component Replacement
Components are replaced when they become unserviceable or when they are life
expired, or when required in the maintenance schedule. When carrying out the
task check the following points:
1. Check the AMM for the correct procedures. Check IPC for correct
replacement identification.
2. Depressurise the system/component.
3. For an electrically operated component isolate that electric circuit.
4. Check that a correct replacement is available - check description
part numbers, mod state, and life remaining - if applicable.
5. Check 'new' item against stores release certificate (EASA form 1).
6. Drain/ shut-off fluid.
7. Jack aircraft if necessary.
8. Remove 'old' component.
rnoodull l A-1145
9. Remove blanks from 'new' component; inspect for general condition
and fit. Secure pipeline connections and connect any electrical
connections; inputs form control systems etc.
10. Return old component suitably labelled, blanked etc to stores.
11. Prime/ bleed system.
12. Carry out a functional test, record and sign relevant paperwork.
System Testing
E;!efer to the AMM. One circuit only may require testing but the points listed below
assume that the whole system is to be tested.
systems.
Carry out any BITE checks.
Use aircraft electrically driven pumps (with external electrical power)
or connect external hydraulic test rigs. Quick release self seal
external connections are as follows: /
rnoodull lA-1146
Generally pumps can be tested:
x
Engine driven pumps - during an engine run.
* Air driven pumps - during an engine run.
* Electrically driven pumps - with external electrical power.
* RAT pump - with external hydraulic test rig connected.
* Power transfer units - with power source system running.
* Hand pump - when driven pumps are off.
rnoodull l A-1147
CONTENTS
Page
rnoodull l A-1148
ICE FORMATION ON AIRCRAFT
The actual amount and shape of the ice build-up depends on surface
temperature, which results from a n energy balance arising from heat input
from viscous or kinetic air heating, hnetic heating by water droplets and the
latent heat of fusion, a n d losses from evaporation or sublimation, convection
and by warming the impinging droplets.
When the temperature is less than 0°C all the impinging water droplets are
frozen, and when it is above 0°C none are frozen. However, for a particular set
of atmospheric conditions and altitude it is found that there isquite a wide
aircraft speed range over which the energy balance gives a skin temperature of
0°C a n d ,this energy balance occurs a t one end of the speed!range by all the
droplets freezing and at the other by none freezing. The potential "catch rate"
or "impingement rate" and the actual_ icing rate are t h u s not simply relatcd in
I
this region. I -
The "no icing hazard" speed depends, therefbre, on the free w k e r content of the
atmosph,ere as well as the temperature and altitude. For severe conditions it is
about the-mmaximumspeed of subsonic aircraft. The final influencing factor of
note is t h a t icing does not occuiabove about 12,000m (40,000 ft) since the
droplets are all frozen a n d in the form of ice crystals and will not adhere to the
aircraft's surface. Relative humidity is also very low.
It is interesting to note that icing can occur within the temperature ambient
range +25"C to -15°C depending on the energy balances stated above. Outside
this range ice will not form.
Hoar Frost
Rime Ice
This ice formation, which is less dense than glaze ice, is a n opaque, rough
deposit. At ground level it forms in freezing fog and consists of a deposit of ice
on the windward side of exposed objects. Rime is light and porous a n d results
from the small water drops freezing as individual particles, with little or no
spreading.
Aircraft in flight may experience rime icing when flying through clouds with the
air temperature and the temperature of the airframe below freezing point; thc
icingbuilds u p on the leading edge, but does not extend back along the chora.
Ice of this type usually h a s no great weight, but the danger of rime is that it
will interfere with the airflow over wings etc, and may choke the orifices of the
carburettor, air intake and Pitot static probes
Glaze Ice
I '
Glaze ice is the glassy deposit that forms over the village pond after a frosty
- - - -
night. On aircraft in flight, glaze ice forms when the aircraft encounters large
water drops in clouds or in freezing rain with the air temperature a n d the
temperature of the airframe below freezing point.
Ice formed in this way is dense, tough and sticks closely to the surface. It
cannot easily be shaken off and, if it breaks off at all, it comes away in lumps
of a n appreciable and sometimes dangerous size. The main danger of glaze ice
is still aerodynamic, but to this must be added the dangers of increased weight,
unequal wing loading, propeller blade vibration and ice shedding debris
damage to tailplanes, rear engines etc. Glaze ice is the most severe a n d the
most dangerous form of ice formation on aircraft.
Pack Snow
Normally, snow falling on an aircraft in flight does not settle, but if the
temperature of the airframe i s below freezing point, glaze ice may form from the
moisture in the snow. The icing of the aircraft, however, is primarily due to
water drops, though snow may subsequently be embedded in the ice so formed.
Conclusions
(b) Drag will increase due to the rough surface, especially if the
formation i s rime ice. This condition results in a greatly increased
I
- - - -
(e) Increased load a n d wing loading. The weight of the ice may prevent
the aircraft from maintaining height, or even taking off.
(i) Debris damage. Caused by sections of ice breaking away from the
airframe a n d hitting tail-planes, rear mounted engines etc. This
has caused serious accidents in the past.
(1) Flutter. Ice can change the pattern of the airflow around the
control surfaces, mainplanes etc, a s well as change the centre of
gravity of the component - thus allowing flutter to occur.
It is evident from the above that the airframe and systems prone to icing be
kept ice free both before and during take-off (ground de-icing) and during flight
(aircraft de-icing). Ground de-icing is carried out by maintenance personnel
prior to aircraft take-off and aircraft de-icing is carried out by on-board
systems.
ICE DETECTION
Most detectors detect the actual ,presence of ice on the airframe, some (rarely)
measure the two parameters required for icing to occur (moisture and
temperature) and infer that icing conditions exist.
I
Many different methods are used to detect the presence of ice. The actual
method used is dependent on the aircraft type and manufacturer. With some
aircraft there is a main detector system (often electrical/electronic) with a
back-up system (often low-tech) .
(b) Inferential Method. This method uses two detectors, one to detect
temperature and the other to detect the presence of water droplets
or moisture. So ice is not actually accreted but that it is inferred
that it might from the two measured parameters. Used in wind
tunnel testing but rarely used on aircraft.
rnoodull lA-1152
Ice Formation Spot Lights
Ice formation spot lights are mounted on either side of the fuselage so as to
light u p the leading edges of the mainplanes in the dark. When required they
can be switched on to allow for visual examination. They can, of course, be
used at any time by the flight crew to visually check that part of the aircraft for
any signs of damage, malfunction etc, not necessarily connected with ice.
/ TERMINAL BLOCK
ICE DETECTOR
QUESTION How would you check this unit for correct operation? (5 mins)
When ice is detected it provides a n indication in the flight deck. The system
consists of a solid-state ice detector and warning system. The ice detector is
attached to the fuselage with it's~probeprotruding into the airflow. The ice
detector probe is caused to vibhte a t it's resonant frequency of 40kHz.
[Resonant frequency is affected by (a)t h e Forcing Function and (b) the Mass of
the object being vibrated - the greater the mass the lower the frequency].
ICE DETECTOR
2
Fig. 3 VIBRATING ROD ICE DETECTOR
When ice forms on the probe, its mass increases and the frequency drops. The
ice detector circuit detects the change in probe frequency by comparing it with
a reference oscillator. At a predetermined frequency the ice detector circuit is
activated. Once activated the probe de-icing heater is triggered to de-ice the
probe a n d return it's frequency to normal. The heater then turns off, to allow
the probe to ice u p again (if icing conditions still exist).
rnoodull l A-1154
This cycle is counted by the system and after a certain number of cycles a n ice
warning signal is sent to the flight deck, and certain de-icing systems are
switched on and/or a signal is sent to a computer - depending on the aircraft.
This cycle will be repeated for as long as the icing conditions exist and when
icing conditions cease the system re-sets itself, turning the ice attenuation
lamp off in the flight deck, and deactivating any de-icing systems that it have
switched on.
QUESTION How would you check this unit for correct operation? (5 mins)
with fingers. I
(d) Holding the probe using "oven gloves" while the unit is
switched on will cause it's frequency to drop and the system
to operate.
(e) Letting go of the probe (as the heater comes on
- -
1
I
Two independent ice detection systems provide flight deck indication of icing
conditions and automatic activation of engine intake thermal anti-ice systems.
Components used by the ice detection systems are; 2 ice detector probes; the
nacelle anti-ice control switches on the anti-iceIrain removal module, a n d the
Engine Indication and Crew Alerting System (EICAS)display. (A CRT - Cathode
Ray Tube - type display on the flight deck).
The left hand ice detection system is powered by 115V ac from the 115V a c
bus 1 and the right system from the 1 1 5 V ac bus 3 . The ice detector probes are
located on the lower front part of the fuselage just aft and below of the Pitot
static probes.
The ice detector probe contains a sensing element, a heater and control cards.
The sensing element is part of an electromechanical resonant circuit which
oscillates a t approximately 40kHz. Ice build up on the end of the element
lowers the resonant frequency by increasing the effective mass of the element.
After a specific amount of ice has accumulated, the heater is activated to melt
the ice and return the resonant frequency to its initial value.
Each ice detector provides a n output to activate the corresponding left or right
side engine anti-ice systems and a separate output for indication of wing icing
conditions. Computations for identifying icing conditions a n d for activating
anti-ice systems are performed in the ice detector.
Control of the anti-ice system is via the Anti-Ice/Rain Removal Module o n the
flight deck. The module includes 4 nacelle anti-ice switches. Each switch h a s 3
positions to place the corresponding anti-ice system ON, OFF or in
AUTOMATIC mode under control of the ice detection system.
A s ice builds u p on the ice detector sensing element during flight, the resonant
frequency of the sensing element decreases. When a 0.02in (0.5mm) ice layer
accumulates, the heater turns on. When the resonant frequency returns to if
i n i 6 d value, the heater turns off, about 8 seconds after it h a s turned on. This
-
process is repeated as long as icing conditions exist. The ice detector keeps
count of the number of icing/de-icing cycles of the sensing element.
I
I
If the wing or nacelle anti-ice control switch is placed in the OFF position then
a message is sent to the EICAS display, the same happens if a control valve
fails to open. If the wing or nacelle anti-ice control switch i s placed in the O N
position and the total air temperature exceeds 12°C a message is also sent to
the EICAS display. If a n ice detector probe fails a message is sent to the EICAS
display.
When the aircraft is on the ground, the icing/de-icing cycle is held a t zero so
that there is no automatic activation of anti-ice systems. However, the ice
detector heater is still enabled on the ground.
moodull l A-1156
The ice detection system can be tested in 2 ways: on the ground using the
Central Maintenance Computer (CMC) and doing an operational test.
CMC Test. For this test electrical power is applied and the CMC does a test of
the ice detection system. If the system fails then it will produce a list of
message pages which include CMC messages, CMC message numbers and
relevant ATA chapter numbers. The CMC Message Index in the fault isolation
manual shows the corrective action for each CMC message.
Operational Test. It is important for this test that the engines must not be
running. Electrical power must be on after confirming that it is safe to do so
and the aircraft must be put into the Air Mode in accordance with the AMM.
Hold your hand near each of the ice detector probes to make sure that they are
not hot. Set the nacelle anti-icing 1, 2, 3 and 4 switches on the anti-iceIrain
removal module to AUTO.
To check the engine anti-ice systems for the left ice detector, put on a heat
resistant glove and apply preisur6 to the probe tip with the th-rnb and
forefinger for one or two seconds.,Release,the probe tip for 15 seconds. Apply
pressure again to the probe tip ,with thumb and forefinger for one or two
I
seconds. Release the probe tip.
-
Make sure that the EICAS caution &&sage. >ICING NAC shows for about 3
1 1
minutes: It is advisable to use a wet cloth or a piece of ice to cool the probe
strut (ndt the probe tip) while you do this test, this helps to increase the life of
the probe. Repeat the same test for the right hand detector. If1 necessary run
through
- -
a "CMC Test" afterwards in accordance with the AMM.
--- - --
Return the aircraft to the Ground Mode in accordance with the AMM and
remove electrical power. Record all work done and sign the appropriate
documentation.
This consists of a short tube, which is closed at its outer end and mounted at
right angles to the airflow and connected to a case. Small holes are drilled in
the leading edge and in the trailing edge of the tube. Dynamic air enters the
holes at the leading edge and passes into the case returning to the airstream
via the holes a t the rear of the tube. A heater element is fitted in the tube to
allow it to be cleared of ice (once formed).
\ \I [ I
I
I
I
I
I
1
I I
I
1
I
CASE HEATER
OVER-HEAT SWITCH
SWITCH
DIAPHRAGM
.
CASE
CALIBRATED ORIFICE
FLOW OF AIR
PlTOT HOLES
I
I
' I
, Fig. 4 PRESSURE OPERATED ICE DETECTOR
I
I 1 I
In flight, Pitot pressure will build u p inside the case and push the diaphr
down. This will keep the switch in the position as shown in figure 4.
- - - - -
When ice accretion builds u p on the leading edge of the probe the Pitot
pressure is cut off. The air pressure now drains away through the calibrated
orifice a n d the rear static vents. The natural springiness of the diaphragm will
cause it to move u p and the switch to close - thus giving a warning signal to
the flight deck.
The switch operation will also cause the heater element to come on in the
probe - t h u s de-icing the probe and resetting the system. This cycling will
continue until icing conditions no longer exist.
A delay may be built into the warning system to keep it activated until after one
complete clear cycle of the system - this prevents the flight deck warning lamp
from flashing on and off during the cycling process.
ANSWER Refer to the AMM. The probe heater can be checked with the
fingers - carefully. The internal heater may be felt from the outside
of the case or be checked using electrical test meters. Of course,
damage, corrosion etc to the unit and probe can be checked
visually. The functional test would require the use of a special
adapter a n d the supply of Pitot pressure. The system would also
have to be configured so the unit thinks the aircraft is in the air
(operate weight switch or airspeed switch). -
I
Rotary Ice Detector (or Napier Ice Detector)
AIRCRAFT SKIN
/
ROTOR
- 11 -
rnoodull l A-1159
Any ice accreting on the front of the rotor is scraped off as it rotates to the rear
where the cutter is. Ice scrapping starts a s soon as the thickness exceeds the
clearance between the rotor and the cutter.
The scraping action on the ice produces a torque reaction on the motor. This is
mounted on a spring loaded gimbal and the torque reaction causes it to rotate
a few degrees in the opposite direction to that of the rotor. This action closes a
micro switch and sends a warning signal to the flight deck.
While ice continues to accrete the torque reaction will remain and the warning
signal stays on. When ice accretion ceases half a revolution later (of the rotor)
the scraping ceases - torque reaction ceases and the motor (within its housing)
gimbals back to it's original position, (under the influence of a spring). This
opens the micro switch and the flight deck warning is cancelled.
QUESTION How would you check this detector for serviceability? (5 mins)
- -
I
-
ANSWER Naturally refer to the AMM, but in general, apart from security,
i '
corrosion, attachment and lay of cables etc, the unit is checked for:
Ice can only be formed when two conditions exist: (1) moisture is present and
(2) the temperature is a t or below freezing. With the inferential method these
two parameters are monitored separately.
The system is not used widely on aircraft but may be found in wind tunnel
testing equipment.
The temperature and moisture detectors are wired in series so that they both
have to show positive for a warning to be given. But note - no actual ice has
been detected.
So when the bridge is unbalanced (due to the presence of moisture) and the
temperature switch is made (due to temperatures at or below freezing) then a
warning is given.
This particular system was to be fitted to the A320 but so far there has been
no experience of this. I t may be fitted to some aircraft.
Principle
-
Beta particles are absorbed by ice-so if one probe emits beta particles the other
probe will detect them. If the probes get iced up then the beta particles will get
absorbed and the detector probe will detect fewer beta particles. At a certain
beta particle count rate a relay in the detector probe will operate causing a
warning to come on in the flight deck. The system is reset by a heater element.
The system is tested by using a strip of Teflon wrapped around one of the
probes - t h i s will-absorb the beta particles and cause a warning to come on and
the de-icing system to work. In general:
(2) The beta particles are emitted from a Strontium 90 Sulphate capsule
(maximum activity = 50 microcuries).
The radioactivity of the probe is, at a distance of 41cm (16 in) roughly
equivalent to that emanating from a luminous wristwatch. The
fuselage wall forms a screen which provides efficient protection for
occupants. However, for ground handling of the probe during
maintenance, some safety precautions should be observed.
rnoodull lA-1161
The ice thickness sensed by the probe sensing surface increases with
the combination of the following parameters:
When the ice thickness increases, the pulse rate of the Geiger tube
measuring the attenuation of the beta particle stream decreases.
The triggering threshold corresponds to 0.4mm (0.015 in) of ice
on the sensing surface of the probe. When the triggering threshold is
reached, the internal relay is energised and causes simultaneously:
* Activation of the ECAM system and illumination of
annunciator lights on the overhead panel.
* Probe de-icing.
(4) 'The particle count signal is fed from the probe to the controller via a
' c6axial cable.
I
I
I
The response action consists in supplying power to the engine air intake and
airframe ice protection systems. The ICE repetition legend on the ICE DET
pushbutton switch goes off 60 seconds after the last ice detection signal.
Maintenance Panel
(1) The system can be tested from the flight compartment by pressing
briefly the ICE/TEST pushbutton switch. The test i s positive if
momentary action on the ICE DET/TEST pushbutton switch triggers
the ice warning (ANTI ICE warning light on the warning light display
panel, single chime, display on the left ECAM display unit). When the
pushbutton switch is released (out),this cancels the ice warning: The
ANTI ICE warning light on the warning light display panel and the ICE
legend of the ICE DET pushbutton switch go off.
moodull l A-1162
(2) Test of the system c a n be performed on the aircraft on the ground by
simulating ice thickness. A Teflon strip is temporarily wrapped
around the sensing surface of the probe. A 0.13mm (0.005 in) thick
strip does not cause ice warning activation whereas a 0.52mm (0.020
in) thick strip does.
Aerofoils.
Tailplane (stabiliser) and fin.
Intakes - engine and APU.
Propellers.
Spinners.
-
Control surfaces.
Windscreens.
Detector probes - TAT, Pitot, engine EPR, angle of attack etc.
Slats.
Carburettors.
Drain masts (grey water and potable water masts).
Waste water connections, escape slide attachments etc.
WATER SERVICE
- - - - PANEL HEAT
LOCKING MECHANISM
AOA SENSOR (ON ALL DOORS)
WINDSHIELD
(ON UNDERSIDE)
ENGINE ANTI-ICE
ANTI-ICE
TAT PROBE
HEAT
PITOT PROBE
HEAT
- 15
- - -
rnoodull l A-1163
Not all these systems will be fitted to all aircraft but you have to be aware that
they do exist and how they work.
De-icing implies the removal of ice after it has formed and anti-icing refers to
the prevention of ice formation. Some equipments can be de-iced - mainplanes
for example - where any removed ice (by the airflow) cannot damage any other
part of the aircraft. Engine intakes are usually anti-iced a s de-icing might
cause lumps of broken-off ice to damage the compressor.
THERMAL
Hot air bleed Wings, tail units, Hot air from turbojet engine
engine intakes, compressor, (rarely exhaust, via a
windscreens, slats. heat exchanger) passed along inside
of leading edge structure or directed
on outside of windscreen.
continued
- 16-
Hot oil. J e t engine nose cone. Engine oil heating - which helps
cool the hot oil.
De-icing Materials
The various fluids used for frost and ice protection and for de-icing aircraft on
the ground are inflammable a n i s m e t i m e s poisonous. Care must be taken
when handling. Use only the correct type of fluid for the s~stem/applicationas
laid down in the AMM chapter 20 Maintenance Practices (typically for airframe
de-icing systems TKS R328 or any fluid to specification DTD 4068).
Each mat is designed for a specific application, the heat output being obtained
from whatever electrical source is available. Mats are available both for anti-
icing or de-icing a n d are rated in watts per m2 (W/m2) or kW/m2.
Anti-icing mats for intakes, are supplied continuously with electricity, while the
de-icing mat is intermittently heated. The total area to be heated is often
divided into several smaller areas with independent mats for each. The
electrical power is then arranged to be switched to each small area in turn.
Thus, on any particular area, there is no heating for a given period during
which the ice builds u p and then, when power is switched to that area,
adhesion is broken by heat and the ice removed by the airflow. (Non intake
applications).
- 17 -
moodull lA-1165
LEADING EDGES
Spraymat
Spraymat is so called because the heater mats are sprayed directly onto the
surfaces to be protected. The surfaces are pre-treated and each spray
application is preceded by a masking process. It comprises of:
- r
Heater Mats
These are used on air intakes on the engine and other components. Heater
mats differ in design and construction according to their purpose and
environment. The latest mats have elements which are made from a range of
alloys woven in continuous filament glass yarn. Other elements are made from
nickel chrome foil. The insulating material is usually PTFE which gives a higher
limiting temperature than synthetic rubber.
The supplies to heater mats are controlled by units similar to those used in
spray mat systems.
moodull l A-1166
The supply for the heaters can be either ac or dc.
System Operation
rnoodull lA-1167
ANSWER The heavy current carrying cables (30 200V ac) are taken the
shortest route from the bus bar to the heater elements (the cables
are heavy). This will then require the use of remote switching
equipment in the form of relays (electrically operated switches). To
route the heavy cables via the flight deck would involve a weight
penalty with large switches for the pilot to operate.
When the system is switched on, direct current energises the power relay (4)
via closed contacts in the overload sensing device (part of 4 in the drawing)
t h u s allowing the 200V ac to flow directly through to the continuously heated
elements a n d to the timer switch (8).The cyclic timer normally controls all
aircraft cyclically heated elements with slow cycle normally selected a t
temperatures below about -5°C.
In the event of an overload, the heater elements are protected by the sensing
device (within 4) which when actuated interrupts the supply to the power rel;.
this= t u r n interrupts the supply of heating current. The current balance relay
(part of 4 or a separate unit) is actuated whenever there is an imbalance
between phases.
I
Misting/fogging (on the inside) and frosting (on the outside) can occur o n the
surfaces of aircraft windscreens. Misting/fogging occurs because of the warm
air in the cockpit contacting the cold windscreen and condensing. Moisture
and freezing temperatures on the outside will cause ice to form on the outside
of the windscreen.
The interspace insulates the inner panel from the outer panel, thus reducing
the coldness of the inner panel and helping to prevent condensation. To guard
against misting in the interspace, complete dryness is necessary and achieved
by electrically-heated elements or more generally by the use of a desiccant
such as silica gel.
EXTERNAL INTERNAL
PANEL PANEL
ASSEMBLY ASSEMBLY
:, 21OUTER GLASS
CONDUCTIVE COATING
3 VINYL ,
4 INNER,GLASS
-
-- -
* Completely sealed.
* Fitted with a valve and expansion bag.
* Fitted with a tube connected to a silica gel container.
* Unsealed.
moodull lA-1169
Dw air type. The windscreen is fitted via a tube from the interspace valve to a
container filled with a desiccant. The desiccant, (silica gel), is in the form of
crystals and has the ability to absorb moisture. The crystals, when fresh, are
blue in colour, but turn to pink/no colour when saturated with moisture and
need to be changed. A Perspex window in the container enables the colour of
the crystals to be inspected. They can be re-activated by gentle heating in a
oven when they will turn blue.
MANUFACTURER PREFIX
DATE OF MANUFACTURER
ONFIGURATION CODE
PART NUMBER
~ x t e r n a Spray
l System
I
It is fitted with inlet, vent and supply pipes, together with a small drain pipe.
The inlet and vent pipes connect with the fluid tank, the supply pipe to the
spray device and the drain to the atmosphere. The pump is controlled by a
switch in the flightdeck.
Servicing will include keeping the holes in the spray device clear, cleaning the
tank filler-neck filter and refilling or topping-up the tank with fluid of the
correct specification. For full details of servicing see the aircraft maintenance
schedule and the AMM.
Functional checks include switching the pump on and checking for fluid spray
coverage on the windscreen.
DOOR
PUMP
Electrical Heat
, -
Electrical Control
The heater film element has to be protected from overheat as this could cause
windscreen delamination.
Figure 13 shows the heater element controlled by a temperature control unit.
Within the unit is a bridge circuit with one element of the bridge connected to
the windscreen film heater. When the switch in the flight deck is switched on it
operates a relay within the control unit. This causes the heater element to start
to heat up. Initially the bridge circuit within the temperature control unit is
unbalanced, but as the screen temperature begins to increase so the sensing
element gets hotter and it's resistance increases. At a pre-determined
temperature (say 40°C) it's resistance is high enough to balance the bridge -
this de-energises the relay and switches off the supply.
CONDUCTIVE
\ COATING
(ANTI ICE)
CONDUCTIVE
/ COATING
(DEFOG)
I
Fig. 12 CROSS-SECTION-OF. D C l O / M D l l SOLID WINDSCREEN
I
I REI!AY GANGED SWITCH
I
I-- -------
115V ac SUPPLY
- - - --
28V d c SUPPLY
SENSING ELEMENT
WINDSCREEN
The system continues in this mode until switched off. A separate overheat
standby sensing element is also fitted (but not shown).
To prevent icing and misting, hot air is sometimes blown over the outside (anti-
ice) and inside (anti-mist) of the windscreen and other transparent panels. The
principle of the outside air blast system is also used for rain clearance on some
aircraft such as the DC8 and the King Air. -
Great care must be taken with ground running aircraft engines with this
system to ensure the system is switched off to prevent overheating the
windscreen.
The hdt air is usually taken from a tapping on the pneumaticducting up-
stream of the conditioning packs. This ducting is usually from the compressor
stage of the jet engine leading to the packs.
Electrical heating is provided for anti icing of each windshield and demisting of
side windows of the cockpit.
The window heater comes on automatically when the engines are started or,
switched on manually prior to engine start or if the aircraft is in the air (signals
via the OR gates). The heating operates a t low power on the ground and a t
higher power in flight. The change-over is automatic via a weight-switch signal
to the computer.
System status data is sent via ECAM (Electronic Central Aircraft Monitor) and
symbol generators to flight deck displays.
- 2.5 -
rnoodull l A-1173
ECAM 4-:
I
WINDSCREEN WASH AND RAIN REPELLENT SYSTEMS
Most ;windscreens are kept clear by windscreen wipers. These are not too
dissimilar to those used on automobiles and are operated hydraulically or
electr-ically. Used to maintain clear-vision through the windscreen when
raining, sleeting or snowing and will clear snow and ice in conjunction with t h e
de-icing system.
They work well on the ground a t normal taxiing speeds and take-off and
landing but in-flight in heavy rain their effectiveness is limited. In some cases
to make rain clearance easier a rain repellent solution can be sprayed onto the
screen. Figure 15 shows a system as fitted to the B747 and figure 16 shows t h e
flight deck control panel a s fitted to the B777.
In figure 15 each front windscreen is fitted with a two speed electric wiper. The
wiper is controlled by a rotary switch. Emergency park selection is used if the
wiper fails to park when switched OFF. In moderate to heavy rain, a rain
repellent may be sprayed onto the windscreen to improve visibility. This is
spread by the wiper to form an even film which allows the water droplets to be
blown away by the airflow. Pushing the same switch down will operate the
wash bottle - which helps clean the windscreen of debris (insects, dirt etc).
rnoodull l A-1174
@
i YQow:
SWEEP
FRG
EMERG
EMERG
WHEN WIPER
PARKOFF
PARK
FAILS
SHOULDSLOW
TO ONLY
PARK BE
AT OFF
USED
1
NOZZLE
WIPERS
-.-..-. . -..-
I I
mu1 ILC
WASH
h -
WINDSHIELD
WASH BOTTLE
--
INOP INOP
INOP ILLUMINATED AMBER -
* THE SWITCH IS OFF
* AN OVERHEAT IS DEECTED, OR
I I * A SYSTEM FAULT HAS OCCURED
OVERHEAD PANEL
Rain repellent is removed from the windscreen on the ground by the use of rain
repellent solution as listed in the AMM.
On some aircraft such as the Boeing 777 the front windscreens are treated
with a hydrophobic coating (hydrophobic meaning water-repellent). This means
t h a t there is no need for a liquid rain repellent system as the water droplets
disperse by the airflow without additional help.
WINDSCREEN WIPERS
Figures 17 and 18 shows the electrically operated blade system for the B757. It
is typical in that it is electrically powered and sweeps the blade over a part of
the forward facing windscreen.
Operational checks are specified in the AMM and are carried out when
specified in the maintenance schedule or after a component change or when a
fault is reported. Remember when operating the wiper that the windscreen
must be kept wet a t all times - otherwise damage to the screen may result.
Ensure the sweep area is clean and smooth from the park position to the
screen.
..
-- WIPER BLADE
(MIDSTROKE
POSITION)
WIPER BLADE
METAL SUPPORT
SYSTEM
W I P ~ RARM HUB
,
/ (SEE DETAIL A)
PRESSURE
ADJUSTMENT SQEEVE ADJUSTING BOLT
(FITTED TO MOTOR
;-- I
DRIVE SHAFT)
\ I
-
] DETAIL A WIPER ARM HUB --
Controls. Check that the controls on the flight deck operate the left a n d right
wipers correctly and as directed. Ensure all flight deck indications are correct.
Sweep. Check that sweep length is correct (as per AMM) and t h a t the blade
does not go over any windscreen sealsledges except when selected to park.
Speed. Check the 'sweeps per minute rate' is within the limits laid down in the
AMM and correspond to the setting control in the flight deck (LOW, MEDIUM,
HIGH). Rates can vary u p to about 300 sweeps per minute. For high sweep
speeds it i s recommended to use a commercially available Sweep Counter.
check for smooth operation on each sweep and that the blade clean.s the
winddcreen correctly.
Rectification
Should it fail any of the above tests then rectification can include, as
appropriate :
* Checking electrical supplies.
* Changing control panel in flight deck.
-k
If sweep or park position is not correct this can be adjusted for at
the adjustment sleeve on the wiper arm pivot bolt.
- 30 -
rnoodull lA-1178
* If speed cannot be maintained within limits (sweeps per minute)
then the motor will have to be changed.
* If blade contact pressure is incorrect this can be adjusted for by
adjusting the pressure adjusting bolt.
* If the blade does not give a clear smear free wipe of the screen then
change the blade.
Remember, when working on the blade or the system to isolate the electrical
supply and tag. After any adjustments/replacements, retest, re-configure the
aircraft and clear all paperwork.
-
-
-
I
I 1
PRESSURE GAUGE ,
LOW PRESSURE
WARNING SWITCH
--- -- --
PROPORTIONING UNIT
F'*-*-I
+
FLUID CONTENTS
+ -
POWER SUPPLY
FILTER
The porous metal element may be made of sintered stainless steel or laser
drilled titanium (expensive).
(Sintering is a process whereby a fine metal powder is pressed into shape with
heat applied to produce a component. If the pressure is not too great then the
component is porous - filters and de-icing fluid distribution panels. Laser
drilling produces hundreds of minute holes per square inch which under
normal conditions are only just visible).
rnoodull lA-1179
METERING TUBE
POROUS STAINLESS STEEL
-.....-...-...
(SINTERED) OR TITANIUM
ISINTEREL.
(LASER DRILLED)
--SUPPLY
QUESTION The distribution panel is fitted on the leading edge of the wing
in such a way as to cover the full range of the stagnation point.
What is the stagnation point? This is theoG-of-flight revision.
(2 mins)
ANSWER The stagnation point is where (in theory) a small molecule of air
I
stays in front of the aerofoil throughout the flight. The actual point
on the leading edge will change with the change in angle of attack -
I
moving down relative to the leading edge with a high angle of
attack and u p with a reduced angle of attack.
There may be a tank contents indication system fitted, either a capacitive type
or a float type. Other system indications may include a low level warning, a
pressure transducer and a low-pressure warning switch. Before the fluid
reaches the distribution panels it goes via a proportioning unit. This meters t h e
quantity of fluid to each panel depending on the panel's size. On a propeller
driven aircraft de-icing fluid may also be fed to the propellers via slinger rings.
It is normal not to have the same system supply fluid to the windscreen a s the
fluid can adversely affect the structure of the windscreen.
rnoodull l A-1180
Installation and Maintenance
Where aerofoils are not symmetrical odd part numbers usually indicate a left-
hand (port) component and even numbers right-hand (starboard) component.
A check should also be made for signs of corrosion, damage and deformation of
the panel profile.
Before fitting check the aircraft structure to which the panel is to be fitted for
corrosion and damage - repairlreplace as per SRM if found damaged.
Tanks. Before installation, the tank should be inspected for signs of damage
and interior cleanliness, and the tZnk supporting structurd checked to ensure
that it is in a suitable condition to receive the tank.
I
Note. The inhibiting fluid should be retained in the pump for the functional
check, the duration of which should not exceed that specified. Do not dry run
the pump.
Filters. After installation, the system should be operated until fluid flows from
the filter outlet connection or, if provided, from a bleed screw hole. The pump
should then be switched off and the filter outlet connection or bleed screw
refitted.
proportion in^?; Units. Before installing a check should be made that they are of
the correct type. Check part number, description, IPC and EASA form 1.
rnoodull lA-1181
Priming and Testing
In general, check that the tank is full and that, when the pump is operated,
fluid flows out from each of the distributor panels. They will appear to sweat
and the drops will run down the underside of the wing to fall on the floor. Pipes
to propeller slinger rings will run fluid freely. Check for correct fluid
distribution and leaks and wire lock all unions.
PROPELLERS
*
Fluid
*
/-
The fluid system provides a film pf de-icing fluid to the propeller blade surfaces
during flight which mixes with1 the water or ice and reduces the freezing point
of the mixture. Where ice h a s already formed on the blades, the fluid
penetrates under the ice and lbosens it sufficiently for it to be thrown off by
centrifugal action.
- --
Fluid is distributed to each propeller blade from a ~lingerring which is
mounted on the back of the propeller hub or spinner. The fluid is pumped into
this ring through a (stationary) delivery pipe.
Some propellers have rubber overshoes fitted to the leading edges of the blade,
to assist in the distribution of the fluid. On this type of installation fluid is fed
from the slinger ring to a small cup, which is part of the overshoe, and is then
forced by centrifugal force along spanwise leading edge grooves (about 1 to
2mm deep and 5mm wide) in the overshoes. The groves finish about 1/3'd to
1/ 2 of the blade length.
The action of the centrifugal force and the airflow will distribute the fluid to
both sides of each blade.
On propellers which are not fitted with overshoes, fluid is fed from the slinger
ring through a pipe to the root of the blade, as before, and is then distributed
by centrifugal force and the airflow over the blade.
rnoodull lA-1182
The fluid may be pumped to the slinger ring from the supply tank by a n
electrically driven pump but pneumatic pressure is sometimes used. The
electric pump is controlled by a switch and, in some installations, the pump
speed may be varied by means of a rheostat. Non-return valves are sometimes
provided to prevent loss of fluid when the pump is not operating.
The slinger ring rotates with the propeller. The pipe and nozzle which deliver
fluid to the slinger ring should be positioned so that there is clearance between
the pipe and the side of the ring to prevent interference when the propeller is
rotating. This clearance is important as the tolerance is small and an error will
cause excessive wear or the system will spill fluid.
- PROPELLER
FLUID DISTRIBUTION SHOE
SUPPLY PIPE I
SLINGER RING
(ROTATING)
PROPELLER BLADE I
-
Fig. 21 PROPELLER FLUID DE-ICING
VP Propeller
For VP (variable pitch) propellers, the propeller feed pipe leading from the
slinger ring to the front of each blade is positioned to end just inside an oval
rubber fluid cup bonded to the front of the blade. There is a small clearance
between the feed pipe and the cup and the arrangement allows the blade to
change pitch and still receive de-icing fluid.
Function Test
rnoodull l A-1183
A suitable dye should be added'to the fluid so that when the de-icing system is
operated the dyed fluid will stain the white propeller and indicate the
distribution pattern over the blades.
Ideally, carry out the test when the engine has to be run for other reasons, and
towards the end of the engine run switch the anti-icing system on. The pump
will pump the fluid to the slinger ring where centrifugal force takes over and
the fluid is forced out through the hole in the slinger ring (one at each blade),
through a short pipe to the beginning of the fluid distribution channels on the
front of each blade.
Centrifugal force and the airflow help to distribute the fluid evenly over both
the front and rear surfaces of the blade.
Before stopping the engine switch off the anti-icing system. Shut down the
engine and inspect the blades.
~ ablade
c should
~ show an even distribution over both surfaces. Uneven
distribution may be caused by the slinger ring being fitted incorrectly, by the
feed pipes from the ring being incorrectly located or by obstructions in the
pipelines.
Often the system is just switched on during a ground run and the blades
checked by feel after engine shut-down. This saves a lot of time painting and
cleaning.
When the system is to be out of use for a long period it is advisable to remove
all traces of de-icing fluid. This may be done by draining the tank and re-fillinb
with a mixture of 95% methylated spirits and 5% distilled water.
The system should be operated until the tank is empty. During this operation
the engines should be run if the system involves propeller fluid de-icing.
The fluid used in de-icing systems is stable and non-corrosive but leaves a
gummy deposit after drying out. Inhibiting the system is at the discretion of the
aircraft operator, but if it is not inhibited it is advisable that a certain level of
de-icing fluid is maintained in the tank and the system operated at regular
intervals.
rnoodull l A-1184
To inhibit the system after draining and/or cleaning, fill the tank with
inhibiting fluid as per the AMM or use fluid DTD 5540. Run the system to
ensure all internal surfaces are coated. Inhibiting is carried out for aircraft
storage and if the aircraft will not be flying in icing conditions for some time.
To de-inhibit the system flush through with a cleaning fluid as per the AMM.
Refill with the de-icing fluid and test.
This is done using dc or ac supplies with heater mats bonded to the leading
edges of each propeller, and sometimes to the spinner. Each propeller heater
mat starts a t the root and has a length of about l/z the blade length. On large
aircraft the supply is 200V 30 ac, on smaller aircraft the supply is dc.
\
Heater elements may also be bonded to the inside of the propeller spinner with
connecting wires from the spinner to the junction box fitted-to the front of the
propeller bulkhead - which r ~ t a t e ~ w ithe
t h propeller.
Wires from each of the blade heater mats also lead to the junction box. The
junction box is connected to slip rings on the rear of the propeller bulkhead.
The slip rings are in contact with stationary brushes fitted in a brush housing
on the engine support structure. The electrical supply goes ithrough the
positive brush gear to the positive (rotating) ring gear through the heater mats
and back via the negative rotating ring gear and negative brush gear.
I
This is a mechanical de-icing system and would not be used for anti-icing.
Pressure and vacuum is supplied to the distribution valves which cycle the
supplies alternately to the supply pipes to the de-icer boots.
rnoodull l A-1185
It is inexpensive to fit b u t disturbs the airflow (at a critical point on the wing -
the stagnation point) when in operation - reducing lift and increasing drag.
The Overshoes
The tubes within the boots are connected to pipelines that supply alternating
pressure a n d vacuum. The external surface of the boots are covered by a
conducting film to allow the discharge of static electricity.
- ----
T h e are,
~ fitted to the leading-edges and can run for the full wing span length.
The width of the boot i s related to thestagnation point range of the aerofoil.
ELECTRONIC CONTROL
ION VALVES
Air Supplies
The tubes are inflated by air from the pressure side of an engine driven
vacuum pump or from a high pressure reservoir or in the case of some types of
turbo-propeller aircraft, from a tapping from an engine compressor stage.
This provides the inflation stage of the operating sequence.
The deflation cycle of the sequence (and whenever the system is switched off)is
provided by vacuum air from a vacuum pump, or, in some systems an engine
compressor tapping using the venturi section of a n ejector nozzle.
Operation
When the system is switched on, pressure is admitted to the boot sections to
inflate each alternate tube. The inflation weakens the bond,between the ice and
the boot surface, causing the ice topbreak away. At the end of the inflation
stage the tubes are fully deflated 'by the vacuum supply.
I , 1
The inflation aqd deflation cycle is repeated continuously while the system is
on. When the system is switched off vacuum is supplied continuously to all
tubes to hold them flat against the aerofoil leading edges thus minimising drag.
- - p-p
Installation
(1) Re-fuelling hoses and other equipment must not be dragged over
the surfaces.
(2) Ladders or service platforms which are placed near the boots
during servicing operations must have soft padding fitted to
prevent damage.
(3) Oil or grease on the surface of boots must be removed as soon a s
possible with soap and water or with a clean rag moistened with
lead-free petrol. Petrol should not be allowed to dry on the surface;
it should be wiped off immediately with a clean dry cloth.
Surface Deterioration
Repairs
I I
Functional Tests
(1) Tests may be carried out using either the aircraft engines or air
supplies from a ground test trolley. If a system is to be tested by
using a test trolley, the air supply must be clean, moisture-free
and at the correct pressure.
Before storing, boots should be inspected for condition and defects. They
should be cleaned and repaired if necessary and dusted with French chalk.
Connectors should be blanked off and the boots rolled up. Rolling should be
' ,
comm6iced at the end remote-from the valve which should be on the outside of
the finished roll. Where connectorsZe located near the centr63f the boot, a
pad of corrugated paper should be placed oper the connectors to protect the
contacting surface.
,
The rolled boot should be carefullywrapped up in a heavy paper to exclude all
light, a& then stored in a cool,:dry, d&k place, away from kyelectrical
running equipment where it will not be crushed or wrinkled. In cases where
boots are bonded to detached leading edge sections, the seqtions should be
wrapped u p and supported on their trailing edges.
- -
- - ---
---- -
In general the leading edge sections of wings, tail units, intakes and slats are
usually provided with a second inner skin to form a small gap between it and
the inside of the leading edge section. Heated air is ducted to these sections
and passes into the gap, providing sufficient heat in the outer skin of the
leading edge to melt ice already formed and prevent further ice formation.
The air is exhausted to atmosphere through outlets in the skin surfaces and
also, in some cases, a t the tips of wings and tail units.
rnoodull l A-1189
The temperature of the air within the ducting and leading edge sections is
controlled by a valve system which depends on the type of aircraft.
(a) A tapping from the compressor stage of a jet engine (common for
large jet transports).
(b) A combustion heater - using a heat exchanger a n d ram air (used
on some piston engined aircraft).
(c) A heat exchanger system using the heat from the exhaust gases.
Not common but used on some aircraft. The air being used for
cabin heating, anti-icing etc.
ANSWER Small piston engined aircraft might use a heater muff (heat
exchanger) around the eihaust pipe. Ram air i s passed through
I which picks u p heat from the exhaust pipe and i s used for cabin
I heating,anti-icingletc.
I Some turbo-prop engines use the jet efflux gases via a heat
I
exchanger for anti/delicing purposes. The gases being passed back
I I
QUESTION Why might the effl'p gases be used in a turbo prop engine and
never on a pure jet engine? (10 mins)
L- ---
In many cases the tapping from the compressor side of the jet engine is
integrated with the cabin air supply system (refer to figure 23) with the anti-
icing air being tapped off to the anti-icing system before the (hot) cabin air
enters the cold air units/conditioning packs to be cooled.
The tapping will be from about the 7th stage, and on some engines there are
two per engine (say 7th and 14th with the 14thmodulated a t high rpm) - but
check the AMM.
With combustion heaters and exhaust heat exchanger systems there is a risk
of carbon monoxide poisoning of passengers and crew should any part of the
ducting down-stream of the combustion area leak. Carbon monoxide detectors
are fitted where there is a risk of such poisoning.
Ducting
In general the ducting may be made of stainless steel, light alloy, or composite
material. The material used must be of the correct specification to resist the air
temperatures encountered a t that particular part of the ducting where
normally metal like stainless steel is used early on in the system where the
temperatures are highest.
Temperature Control
The conEol of the air temperature within ducting and leading edge sections is
important as overheating and b u r n s g of the metal and ducting may occur.
Installation
Refer to the AMM. Always check for security of attachments, corrosion and
damage of components and in general the following applies:
rnoodull l A-119'1
Heat Exchangers. Before installation, heat exchangers should be inspected to
ensure that no foreign matter has entered the various connections, and they
are free from obstruction.
Combustion heaters and their hot air outlet ducting should be dismantled,
inspected, reassembled and pressure tested at least once every 500 heater
operating hours. These hours are assumed to be the same as aircraft flying
hours unless agreed by the CAA to be a percentage of the flying hours. \
~hecg the AMM and the maintenance schedule. The following general points
apply./Check all components for:
Testing
rnoodull l A-1192
CONDITIONING PACKS
ANTI-ICING (OUTBOARD)
- -
INTAKE \
7th STAGE BLEED
ANTI-ICING
Figure 23 shows the BAe 146 anti-icing hot air system. The air supply comes
from a tapping on each engine and also from the APU. The air is fed to the
mainplanes and tailplane (stabiliser).Anti-icing air comes from a separate (7th
stage) tapping on each engine for the intake, splitter lip (between bypass air
and core air) and LP compressor inlet guide vanes.
rnoodull l A-1193
ENGINE ANTI-ICE
SELECTOR
I (THREE POSITION
I ANTI-ICE II ROTARY)
/I
-
OFF THE ENGINE
ANTI-ICE VALVE IS
L ENGINE COMMANDED CLOSED
I AUTO AUTO
OFF@ON OFF@ N OFF@ N
ENGINE,N
AUTO -
ANTI-ICE
FLIGHT, VALVE
THE
IS OPENED OR CLOSED
AUTOMATICALLY BY THE
ICE DETECTION SYSTEM
I I ON -
* THE ENGINE ANTI-ICE
VALVE IS
OVERHEAD PANEL COMMANDED OPEN
APPROACH IDLE IS
SELECTED BY THE
EEC AND
CONTINUOUS
LWING ANTI-ICE SELECTOR (THREE POSITION IGNITION IS
AUTOMATICALLY
ROTARY) Z U ~ D L nu
~ C ~
-
OFF BOTH WlNG ANTI-ICE VALVES ARE
COMMANDED CLOSED
-
AUTO IN FLIGHT, BOTH WlNG ANTI-ICE VALVES
ARE COMMANDED OPENED OR CLOSED
AUTOMATICALLY BY THE ICE DETECTION SYSTEM
-
ON IN FLIGHT, BOTH WlNG ANTI-ICE VALVES ARE
COMMANDED OPEN
' I
The engine spinner is anti-iced by hot engine oil - which also acts a s an oil
heat sink (oil cooler).
Control is via the overhead panel on the flight deck and sections of the system
may be in the de-icing or anti-icing mode.
Figure 25 shows the flight deck anti ice control panel of the B777. Study the
drawing and note the available selections. Note also that the tailplane and fin
are not anti-iced. (EEC = Electronic Engine Control.)
Figure 26 shows the intake anti-icing system for the Airbus A320.
Intake air is taken from a separate tapping from the high pressure compressor
of the jet engine. The air is controlled using an on/off valve which is switched
from a push button (one for each engine) on the control panel on the flight
deck.
The control valve closes when the engine is shut down and automatically opens
in the event of electrical power failure (fail safe).
OVERHEADPANEL
ANTl ICE
- --
Note the 'signals going to FADE$ (Full Authority Digital Engine Control - a
computer involved in the control of the engine) and ECAM (Electronic
Centralised- Aircraft Monitor - for flight deck CRT screen didplays).
These include:
A
Air data probes particularly Pitot heads and TAT (Total Air
Temperature) probes. Some-times static vents.
* External sensing units such as angle of attack vanes.
* Drain masts, in particular external grey water drains.
* Door mechanisms - those that suffer from condensation freezing.
* Potable water servicing valves and internal domestic water supplies
systems where there is a possibility that they might freeze.
The above are anti-iced electrically with single phase 115V ac, although dc is
used on some components. The heater elements may be controlled by a
computer with overheat protection being provided by a n inbuilt thermostat.
If anti-iced slats and flying control surfaces usually use hot air systems.
rnoodull l A-1195
Slats
Figure 27 shows an example of how the hot air is distributed to the leading
edge of the slats. As the slat is moved forward so the telescopic feeder duct
extends. This allows air to the leading edge of the slat a t any position. The air
is allowed to the inside surface of the slat via drillings in the slat duct.
- 48 -
Some systems have automatically reduced power when the aircraft is on the
ground and heaters such as the TAT heater are turned off completely
(automatically).The probe heater control unit takes care of these functions
with interfaces to the landing gear weight switch.
Some control units also have interfaces with the engine vibration monitoring
system and the Central Maintenance Computer (CMC). On modern systems
they will identify and memorise faults.
If current gets too high or too low a warning is signalled to the flight deck
warning computer.
GCU-2
AC BUS 2
RIGHT
GLC-2
4000XU WINDSHIELD
HEATING
BTC-2
LEFT WIN,WW
HEATING
I I L 1 2 D A 2 PROBE HEAT,
I ' 3PU2
FIO TAT
EXT PWR-A
12XU
SIC
EPC-B
EXT PWR-B
1
-
k K A PROBE HEAT.
CAPT PITOT,
PROBE HEAT.
STBY PlTOT
IDA3 HEAT'
STBY ALPHA
C
&y ,
4000XU
G E 1
GCU-1
lXU1
AC BUS I lXPl
IDGI
12DAl
2DA1
WINDSHIELD
LEFT
HEATING
WASTE WATER
OUTLET
Testing
Always refer to the AMM. On older aircraft testing is done carefully with the
fingers by switching the heaters on and noting the temperature (an accurate
reading can be obtained by the use of temperature indicator tongs placed
around probe type heaters). On modern aircraft inbuilt testing (BIT) is carried
out every time system power is switched on, and on command from the central
maintenance computer. The tests involve checking computer equipment such
as the CPU, RAM etc, also inputs and outputs and the integrity of heater
probes.
Figure 29 shows the heater details of a grey water drain mast (called grey water
to denote that it comes from the hand basins and sinks of the aircraft
(moderately clean) - with blue water indicating that it comes from the toilets
which is not allowed overboard of course). Note the heater element,
temperature sensor and over temperature switch.
Figure 30 shows the general layout of a probe heater computer. Note the
heaters of the various probes. Note also the 1 1 5 V ac single phase supplies via a
dc operated relay and the 28V dc supply. Note the logic inputs from the
engines and landing gear and the data connections to the CMC.
HEATING
-11 CASE GROUND POWER
SUPPLY
AOA POWER
SUPPLY INPUT 1-1
901XPC
PITOT POWER
34-1 1 4 0
101XPA TAT POWER
SUPPLY INPUT
ENG 7.
I ENG 2 RUNNING
OR FLIGHT INPUT
I ENG 1 RUNNING OR
FLIGHT INPUT
ElVMU 73-25-00 HEATING A V A I L A B I L I T Y
- - OUTPUT 31-54-00
/
BUS 3 TATNOHEATOUTPUT
RESET,
PlTOT FAULT OUTPUT
LGCIU 2 'FLIGHT' INPUT
VALID LGCIU 2YALIDAT~ON'
INPUT CHANNEL A OUTPUT
5GA2 LGCIU-2
ADIRU 34-11-00
Page
Indication systems
Undercarriage selection
Retraction testing
Undercarriage configuration
Bogie units
Shock absorbers
Liquid spring oleos
Gas oil oleos with separator
Gas oil oleos without separator
Servicing equipment
-
- --- -
LANDING GEAR
Once airborne landing gear serves no useful purpose and is so much "dead
weight". Because it h a s a comparatively large mass and plays no part in the
actual flying of the aircraft several attempts have been made to replace it. For
example for take-off, trolleys which are left behind, have been used but landing is
a problem.Other systems have been tried but so far no practical alternative has
been found to the undercarriage (or landing gear) as we know it:
*
-
I
I ;
J;
Four undercarriages - 2 mains and 2 nose units - some helicopters.
-
* Multi bogie units housed-within the fuselage and a nose unit. Large
--
transports. -- - -- -
Tricycle Configuration
The majority of aircraft are of the tricycle type with either a nose wheel or a tail
wheel. The main units are usually housed in the mainplanes (for lateral ground
stability), but on some aircraft these are housed in the fuselage. On some nose
wheel type aircraft there may be main landing gear in the wings (wing gear) and in
the fuselage (body gear) with a total of 3 (DC10 - two mains and one centre
fuselage), or 4 main gear units-(B747 - two wing and two body gear).
Main landing gear is positioned to give ground lateral stability and is near the
aircraft's longitudinal C of G - for nose wheel aircraft just aft of the C of G and for
tail wheel aircraft just forward of the C of G.
Initially, tail wheeled aircraft gave the propeller of powerful fighters clearance from
the ground with out having excessively long landing gear units.
rnoodull l A-1201
In general, the nose landing gear arrangement as opposed to the tail wheel system
is preferred because:
* It provides better pilot vision.
* It means the aircraft is already in the normal flying attitude - less
drag, and thrust is in the correct direction (not pointing downwards).
* It provides easier loading.
* It prevents "nose-over" during heavy braking.
* It reduces the possibility of ground looping (a sort of over-steer where
the pilot steers the aircraft a small amount from the dead ahead
position and it will steer too far - caused by the fact that the C of G is
behind the main wheels).
The requirements for landing gear is laid down in J A R 2 5 and covers the following:
* General requirements.
* Shock absorber tests.
-
* Limit drop tests. ,
L ,* - Reserve energy absorption drop tests.
* Retraction mechanisms.
* ; Wheels, tyres and brakes.
* Nose wheel steering.
It is not usual to incorporate a brake unit in the nose or tail wheel but some
aircraft do have them (B727 has a brake unit in the nose landing gear for
example).
These loads can be substantial particularly compressive loads when landing and
are transmitted to strong points on the airframe.
Types of Undercarriage
The wheels are mounted on axles attached to the bottom of the leg so that they
transmit compressive loads to the shock absorber. There are two basic methods of
mounting the shock absorber (figure 1):
Direct Acting. The shock absorber (oleo) may be an integral part of the leg or it
may be a separate unit within the leg, but an any rate the compressive forces are
transmitted to it directly u p from the axle. If it is an integral unit it is designed to
take all the additional stresses, bending, torsional etc, as well as the compressive
loads. -
- - -
Torque liliks are required to prevent axial rotation of the sliding portion of the leg
within the main unit. The torque links keep the wheels pointing in the right
direction. Figure 5 shows the use of splines for this purpose - this method is rare.
This type of suspension lends itself to being used on nose wheel and tail wheel
assemblies as it can be made to caster to from a trailing unit. (Caster = to turn in
the direction the aircraft is going.)
AIRFRAME ATTACHMENT
LEVER
- j-
rnoodull l A-1203
Camber (figure 2)
This is defined as the inclination of the wheel with respect to the vertical plane
when viewed from the front or the rear of the aircraft. Most large aircraft have a
zero angle of camber for all wheels but many small aeroplanes do have cambered
main landing wheels.
Positive camber is where the wheel is inclined away from the aircraft and negative
camber is where the wheel is inclined towards the aircraft. Camber i s checked by
using a clinometer (adjustable spirit level) placed on the rim of the wheel (using a
straight edge where necessary). The aircraft should be jacked for this operation -
but check the AMM.
Fig. 2 CAMBER
rnoodull l A-1204
NOSE UNDERCARRIAGES
To some extent what applies to nose landing gear also applies to tail landing gear.
The nose undercarriage is usually of lighter construction than the main gear
because it normally does not have to take the initial landing shock and on most
aircraft also does not have to take any stress related to braking. It does, however,
have to carry provision for towing and must withstand bending and shear loads.
QUESTION Can you list four or five features that a nose undercarriage has to
have that a main gear does not have? (5 mins)
ANSWER For most large aircraft the nose unit will have:
J; The ability to caster.
-k A self centring system.
* A steering system - powered for large aircraft..
* An anti-shimmy device.
I
* No brakes - usually.
-
Castering --
To enable the aircraft to be manoeuvred on the ground the nose'wheel must have
the ability to align to the direction the aircraft is going. It must caster freely to at
least the maximum angle the aircraft-is allowed to turn. There will normally be
internal stops to limit its angle of travel and markings on the outside will give an
indication to personnel towing the aircraft of the maximum limit of travel. O n no
account must any attempt be made to exceed this limit.
Self Centring
With the spring loaded cam system - at the top of the castering unit there is a V
shaped cam down into which is pressed a spring loaded roller. When the leg
casters the roller is forced u p one side of the V slot against the pressure of the
spring.
When the weight of the aircraft is removed from the wheels the spring forces the
roller down into the middle of the V slot rotating the leg into the dead ahead
position.
To prevent the nose gear retracting should it not be in the dead ahead position the
down lock is usually connected to the castering system mechanically so that if it
is not dead ahead then the down lock will not disengage.
Centring jacks, either as a separate unit or fitted in the steering motor, rely on
hydraulic system fluid pressure when u p is selected to centre the leg. Again, the
down lock is inter-connected to prevent the leg retracting should it not be centred.
Steering
Some small aircraft do not have a steerable nose wheel (or tail wheel) they are
steered using differential braking. Apply the brakes on the left hand side and t h ~
aircraft will steer left - apply the brakes on the right and it will steer right. Many
small'airEraft have nose wheel steering systems which are mechanically
connected to the rudder bar. When the rudder bar moves so does the nose leg - in
the air;-as well a s on the g o u n d !
I
Large $rcraft have powered nose wheel steering, this is because the wheels would
be imGossible to move manually.
QUESTIPN How much weight is felt through the nose undercarriage? (2 mins)
ANSWER T h e actual weight (or more correctly 'mass') that is felt through the
- - - -
To allow the nose unit to caster when towing the aircraft there must be some
means of disconnecting/isolating the powered steering. This can be done in
several ways:
* A by-pass valve fitted in the system (figure 6). When the steering is
switch off the valve is opened allowing free movement of fluid between
both sides of the jack when it moves due to the nose gear being
turned when towing. When steering is selected the valve is closed by
hydraulic pressure.
A
By disconnecting the torque links during towing/pushback. This
allows the unit to caster without moving the steering jack.
J;
By the use of a n "isolating pin" which is inserted into a special hole in
the nose unit by the pushback crew - this effectively isolates the nose
gear steering mechanism. The pin is removed after pushback and the
usual procedure is to show it to the pilot before he/she
, , taxies the
aircraft away.
Power steering systems are usually operated hydraulically usink main system to
operate either:
(a) A single jack with a n equal area both sides of the piston, or
[ e
---
- -
--
u STEERING
PLAN VIEW
DUAL UN-EQUAL
SINGLE EQUAL AREA JACK
rnoodull lA-I207
QUESTION Why does the single jack have the same area both sides of the piston?
(2 mins)
ANSWER If the areas were not equal the jack would move faster one way than
the other (given the same fluid supply conditions).
QUESTION With reference to the drawing below. The jack is of the unequal area
type. Which way will it move the fastest - in or out? (2 mins)
IN 4-----c OUT
ANSWER - -
It would move IN the fastest. The reason is that there is less volume
to fill as some of the volume is taken u p by the piston ram.
Remember, that the rate of movement of a jack is governed by how
fast the jack volume can be filled. Given a fixed hydraulic supply and
a certain size jack the rate of fluid flow governs the speed of
movement and the pressure governs the load that can be moved.
Control I
Steering is controlled from the flight deck, depending on the aircraft, by:
The steering control will select a hydraulic four way selector to port pressure fluid
to one side of a jack whilst opening up the other side to return. The jack/s may b e
a simple jack as shown above or may incorporate a:
* Self centring jack.
J; Shimmy damper.
* Relief valves.
Feedback
The control mechanism is not too unlike that of a Powered Flying Control (PFC)
system - in principle at least. I t cannot simply be selected one way o r the other, it
has to have some form of feedback.
moodull l A-1208
QUESTION There are two types of feedback - can you name them? (2 mins)
QUESTION PFCs and powered steering use negative feedback in their control
systems. C a n you describe negative feedback? (5 mins)
Shimmy Damper
ATTACHMENT TO
NON MOVING PART
When shimmy tries to occur and the unit tries to oscillate the piston tries to move
back and forth through the oil quickly - the frequency being relative high and of
low amplitude. Because of the viscosity of the oil it resists these quick movemen
and 'seems!to "lock-up" the damper.
I I
With ordinary castering/ steering the piston moves with the oil flowing steadily
through the ports.
-- -- ppp -
Twin Wheeled Units. These assist in reducing the tendency to shimmy as each
tvre has its own natural shimmy frequency (associated with wheel rpm). When
<here are two wheels their natural frequencies rarely coincide, one tyre tends to
dampen the vibrations of the other and shimmy is eliminated or significantly
reduced.
blank
POWER STEERING SYSTEMS
The hydraulic supply comes from one of the hydraulic systems. On some aircraft
there is no back-up supply as steering can be achieved using differential braking
if necessary - and the brake system will have a main supply with a standby.
When a steering command is imputed the selector valve selects, the jack moves
and the negative feedback de-selects to stop the jack movement. When power
steering is switched off or isolated the unit is free to caster. Immediately prior to
retraction the system is switched off and the unit centred.
--
A Single Jack System (figure 5) I
This shows one method of fitting a jack to the nose gear. In this arrangement the
jack ram is fured to the non-steering part and the jack body is connected to the
steering part. In other systems it is fitted with the jack ram moving the steering
-
Part. - -
Remember that splines are very rare, torque links are far more common -
connecting the top part of the rotating unit to the bottom shock absorber part.
The fluid connections to the jack in figure 5 are through the jack ram ends. As
fluid pressure is ported to one side of the jack the body moves and through the
connecting link steers the wheels to port or starboard. In this aircraft the follow-
u p linkage (negative feedback) is an electro mechanical system using a drum
switch moved by the steering jack.
blank
STEERING
CONNECTING
SHOCK ABSORBER
(OLEO)
LE FITTING
TOWING
CONNEC1
A Centring Jack
This jack may be a separate unit or fitted as part of the steering jack. It comprises
a piston rod anchored to the undercarriage leg, a jack body connected to the
steering part and an inner piston.
- 12 -
rnoodull l A-1212
When the undercarriage is selected up, the steering system is isolated and fluid
pressure is fed to this jack. This causes the inner piston to move to the end of its
travel in one direction and the jack body to move to the end of its travel in the
other direction. In this condition the nose leg is centred.
On some aircraft the steering system is isolated by the weight switch as soon as
the aircraft takes off.
In this system the single jack moves the nose wheels via a rack and pinion gear
(similar to the Airbus system). Selection is made in the flight deck via the steering
cables to operate the steering drum. The feed back mechanism i s via the follow-up
cables - for example:
6. ' This puts tension into the right hand side of the follow-up cable and
slack into the left hand side - releasing the tension i n that side.
7. This pulls the beam back to its level position, neutrhlises the selector
'
valve and stops the steering action.
-
If the pilot continues to move the steering input, the selection will be maintained
with the follow-up cables trying to catch u p the steering cables - and cancel the
input. A s soon as the pilot stops his/her input the follow-up system catches u p
with the input system the valve goes into neutral, movement stops and the jack is
held in that position by an hydraulic lock.
NOTES
QUESTION Why would the flow vary from the hydraulic system? (10 mins)
ANSWER For 90% of aircraft the hydraulic circuits - flaps, slats, landing gear,
brakes etc - are connected in parallel and then connected to the
supply circuit. That is, they all experience the same pressure (unless
there are pressure reducing valves fitted) but they share the total
available fluid flow. If one of the circuits is selected - say flaps - the
fluid flow rate to the power steering will be reduced (and incidentally
also to the flaps). When no other services are selected the fluid flow
rate to the steering circuit is high and the throttling valve will move to
the nearly closed position. When other services are selected the fluid
flow rate is reduced, the valve is more open and the flow to the circuit
is the same a s before - this ensures a constant speed of operation
irrespective of the selection of other services.
- 14 -
rnoodull lAp1214
The by-pass valve may be actuated hydraulically of electrically a n d when open
allows fluid to pass freely from one side of the steering jack to the other (for
towing, pushback etc). In the drawing it is hydraulically operated so when
steering is selected pressure to the top of the valve causes it to close. When un-
pressurised fluid from either side will pass easily through the lightly loaded spring
valve.
A two way pressure relief valve allows the relief of any excessive pressure on one
side of the jack to be relieved to the other side - possibly caused by the tyres
catching a taxiway/runway light.
On retraction the system will have provision to ensure the unit is centralised
using a centring link or a centring jack.
An Electrical System
The hydraulic side of the system-is similar to the one described-above but the
control and feedback is electrical. The selector valve is electrically operated and
the feedback is provided by a Wheatstone bridge (figure 7).
The bridge has four resistors, two of which are a fxed value and two are variable.
It is supplied with 28Vdc.
-
In simple terms if all the resistors are the same value then the voltage (and
current) in both arms of the bridge will be the ,same. If the voltages between the
left and right arms of the bridge are compared'then they will be the same and
there will be no voltage difference at the amplifier - and no output to the hydraulic
selector. - - -
-
28V dc SUPPLY
RESISTORS
AMPLIFIER
- lh -
rnoodull lA-1215
If the bridge becomes un-balanced (by movement of the pilots input resistor) then
more current flows down one arm of the bridge - there is a voltage difference
across it, this is amplified and selects the valve. The undercarriage moves and the
valve will be de-selected when the follow-up resister reaches the value of the input
resister.
For example, when the pilot moves the steering control wheel it will alter the
steering input variable resistor (say UP). This means that more voltage is dropped
across that resistor so the right hand side of the bridge has a higher voltage (and
h a s more current). This voltage difference is felt by the amplifier to pull in a relay
(left hand one) within the selector valve. The selector valve selects to move the
nose leg in the appropriate direction. When it moves it changes the value of its
follow-up resister - in this case UP.
While the pilot continues his/her input the follow-up resister will continue to
chase the input resister. When the hand wheel is stopped moving, the input
resistor stops and a fraction of a second later the follow-up resistor reaches the
same resistance value. This balances-the bridge, the amplifier senses no voltage
difference, no signal is sent to the selector valve, it de-selects and the nose gear
stops moving.
Notes. 1. For more details of ;the electrically operated four way selector valve
see the book in this' series entitled Hydraulics.
2. The follow-up resistor (potentiometer) is usually fitted directly on
the nose leg and the rest of the bridge is in the aircraft somewhere -
'
probably behind the instrument panel.
A Computerised System
Again, the hydraulic side of things is very similar to the system shown in figure 6,
it is the selection and control that is computerised.
You will have to take my word for it that a digital computer is basically a very
simple machine. It has many things in its favour such as small size, low power
consumption, inexpensive, speed of operation etc, but the actual operations the
micro processor can do are strictly limited. The digital functions it can perform
are :
And that's all. There is no need to discuss this any further but if you want more
infomation on the processes then a ten minute 'phone call to your tutor will
explain all.
The computer will take the steering input signal and convert it to a digital signal
and put in store (2.).It will convert this signal to a n analogue signal to select a
hydraulic selector valve - this moves the nose gear which will send a n analogue
feedback signal back to the computer. This is digitised and this feedback signal is
compared (4.) to the orignal input signal. If the two signals are not the same the
selection is continued and when they are the same the steering signal will stop.
Figure 8 shows a schematic of the A 3 2 0 system. The pilot's steering input is sent
to the BSCU (Brake and Steering Computer Unit). The steering signal can come
from the rudder pedals that can be isolated by the rudder pedal isolation button
on the steering wheel.
QUESTION With reference to figure 8 what other computers have an input into
the BSCU? (2 mins)
rnoodull l A-1217
QUESTION Again with figure 8 - when can power steering be used? (5 mins)
With all these conditions made the AND gate will allow steering.
UNDERCARRIAGE SYSTEMS
(a) A retraction system to raise and lower the gear and doors.
( b ) ' A reliable locking system to operate in the u p and the down positions.
(c)I An indication system to indicate to the crew the status of the landing
gear.
(d) Wheels, tyres and brakes (covered in other books in this series).
(e) Systems to interconnect the gear with other services such as low
1 I
The most common form of retraction system is hydraulic (see the book in this
series entitled Hydraulics), butsome aircraft may use electrical actuation and
others may use pneumatics (for pneumatic systems refer to the book in this series
by that name).
Provision must be made for the emergency lowering of the gear should the main
system fail. Emergency/ back-up systems can include:
* A second hydraulic pump in the power supply system.
J;
Standby pumps - ram air driven for example (RAT).
~i
Duplicate (or even triplicate) hydraulic supply systems.
* The use of a compressed nitrogen blow down system.
-k
Gas operated release locks and free fall of the gear with spring
assisted down locks.
* A hand operated wind down system (not common).
- 18 -
rnoodull lA-1218
Locking Methods
J A R 2 5 states that there must be a positive means to keep the landing gear
extended in flight and on the ground and to keep it in the correct retracted
position.
ANSWER Mechanical.
Hydraulic.
Geometric.
Mechanical locks are the most positive and reliable so meet the requirements of
JAR25.The actual design can vary from a plunger moving into a machined hole
between two links of the landing gear-to a hook type unit locking onto a bar.
Nonnally actuated hydraulically and usually fitted with a micro switch/proximity
I
switch for flight deck indication systems.
A hydraulic lock might also be used - but normally only as a back-up a s it is not
very reliable.
--
A geometric lock might also be used - also as a back-up (figure 9). A geometric
lock is a series of links - usually three including the undercarriage leg, and so
arranged a s to try and stay in one locked position. The links can be moved out of
the locked position by a jack.
0 = HINGE POINTS
Position indication of the landirig gear (UP or DOWN) is signalled to the flight deck
by a lamp system; on CRTs on some aircraft, and there is usually a mechanical
back-up indication system.
I
Leg and fairing doors are usually moved by separate jacks with sequencing being
carried out hydraulically, electrically or mechanically.
Provided to give an indication in the flight deck of the leg position/door/s position
- usually in the form of coloured lights and, if a CRT display is provided, by a
small display.
With reference to figure 10. Micro switches or proximity switches are operated by
the u p and down locks and are wired into indicator lamps in the flight deck. There
is usually one lamp per indication per undercarriage (with CRT indication a s well
on some aircraft). Where lamps are used standby lamps may be provided. In basic
terms lamp indications are:
moodull l A-1220
In some aircraft an amber light will show if the aircraft is on the ground and the
fairing door i s moved from its normal position (for servicing).
To warn the pilot if the gear is not locked down on approach an additional
warning system is provided. This may be v i a the throttle switch, a s in the
drawing, or it may be via the ground proximity warning system or wired into a
Pitot pressure operated micro switch.
On many aircraft mechanical standby indicators are also fitted (figure 12).
Figure 10 shows the gear in the unlocked position with a 28Vdc supply to the red
lamp via both micro switches.
If the gear is on the way up then the next thing to happen is the uplock
micro switch is operated breaking the circuit to the red light and the light goes
out.
If the gear is on its way down the next thing to happen would be that the
downlock micro switch operates to switch off the red light and switch on the
green.
If the throttle is pulled back past a certain limit (for landing) with the gear not
locked down then the throttle micro switch is live and will make contact giving an
aural and visual warning as well as signals to the CRTs and CONFIG warnings
etc.
Most modern aircraft have a configuration warning system to check that all
system are set correctly for a particular operation - eg landing, take-off etc.
rnoodull lA-1221
For signals being sent to lamps the current goes directly to the lamp and then to
earth return. For the CRT displays the signals (discrete ON or OFF) are sent to the
Symbol Generator Unit (SGU) - a computer with stored symbol data for
transmission to the CRTs.
UPLOCK DOWNLOCK
MICROSWITCH MICROSWITCH
FUSE
CRT DISPLAY
INDICATION
I w
WARNING SIGNAL
Figure 11 shows a typical modem flight deck indication and warning system. It
shows the A 3 2 0 system using ECAM displays (Electronic Aircraft Centralised
Monitor). This is a computer based system using CRTs and SGUs to show
coloured symbols and pictures on the screen. The Landing Gear Page must be
selected on the control panel for gear data to be displayed.
o
extension
r / -
lnr -19 'c
2 P\
2 22
G.W. 60300 n;
1 Landing Gear
Seleclor ,Lever
Brake pressure
lndlcatlon
(allernate system)
- -- -- - -
The selector system might be a simple cable or push/pull rod system connecting
the flight deck lever to the hydraulic selector valve. More likely on modern aircraft
it will be an electrical system.
The selector lever will be tactile (that is shaped like a wheel so it can be found in
the dark - if necessary). It will also be instinctive - moved up for u p selection and
down for down. When operated it will make an electrical contact to operate a
solenoid in the selector valve and will have a safety interlock that can be
overridden in an emergency.
FLOOR HATCH
WINDOWS
FREEFALL HANDLE
HANDLE
VISUAL DOWNLOCK
In the simplified system shown in figure 13 the selector lever makes contact in
either the u p or down position to provide a 28Vdc supply to solenoids in the
electro-hydraulic selector valve. This will select to move the gear to either the fully
u p or fully down position.
When down is selected and the weight is on the wheels the safety interlock (weight
on wheels lock) solenoid circuit is broken and it moves out under spring pressure.
In this position it prevents up selection being made. When the aircraft takes off
the circuit is made by the squat switch, operating the solenoid and withdrawing
the weight on wheels lock, the undercarriage can be selected up. The emergency
override is a button which allows for gear u p selection when on the ground - it is
rotated to re-align the two legs' either side of the weight on wheels lock and
pushed in.
Note. The squat switch may be called:
* Weight on wheels (WOW) switch (Airbus).
J;
Ground sensor (tockheed and Douglas).
* Ground air sensor (Boeing).
* Flight ground switch (KLM).
Figure 13 is a simplified drawing that shows the principle of how the system
works. Figure 14 shows an actual selector a s fitted to a B747-400. Note that the
selector panel has the following differences:
J:
Provision for OFF selection which depressurises the landing
gear system.
* Has a lever lock override switch that releases the landing gear
lever.
* Has alternate gear extension switches.
-- --- - -- -
I
Retraction Testing
These will be required after any work is carried out on any part of the gear
retraction system and as specified i n t h e maintenance schedule. The tests will
verify the correct operation of the mechanical, electrical, electronic, and hydraulic
systems. I
I
- - -
UP SELECTION
WEIGHT ON
WHEELS LOCK
SOLENOID I
, ELECTRICALLY OPERATED
1
Fig. 13 SELECTOR CONTROL SYSTEM
r n o o d u l l lA-1225
The actual testing to be carried out as per the AMM.
The aircraft must be jacked inside (or outside provided the forecast wind speeds
are less than those specified in the AMM, the weather is fine and it is on hard
standing).
The electrical and hydraulic systems must be serviceable and barriers erected and
warning notices posted to keep people away from the area around the landing
gear. Place look-outs.
Steering Testing
Check steering operates with the rudder pedals -if provided for.
Jack the aircraft clear of the ground.
Set the nose gear a few degrees to' one side of the ,dead ahead position
and select landing gear up. Check nose gear centi-es before the down
lock disengages.
Lower the landing gear and repeat item 12 but with the nose gear
displaced in the opposite direction.
With the gear u p check that steering is inoperative.
Lower the gear.
Check any standby supplies to the steering motor including electric
pumps, hydraulic accumulators etc.
Check any warning/indicator systems.
Remove the steel plates by raising the aircraft or towing the aircraft
forward a little.
Record all the work done and sign the appropriate aircraft
documentation.
UNDERCARRLLZGE CONFIGURATION
The increase in size and All Up Weight (AUW) of modern aircraft has led to an
increase in wheel loading; this being defined as the static load on each wheel of
the landing gear a t aircraft take-off weight. This term is not very precise when
calculating the actual force per unit area (psi)that each tyre puts on the ground.
rnoodull l A-1227
LANDING GEAR LEVER
UP - r e l e a s e s downlocks
- p r e s s u r i z e s up s i d e o f g e a r a c t u a t o r s
OFF - d e p r e s s u r i z e s l a n d i n g g e a r h y d r a u l i c
system
DN - releases uplocks
- p r e s s u r i z e s down s i d e of g e a r a c t u a t o r s
-
ALTN - r e l e a s e s g e a r doors and gear
uplocks
GENTER PANEL
\ c-
A more precise term, called the California Bearing Ratio (CBR) indicates the ability
of a runway surface to support a load.
I
In general the lighter the aircraft the less pressure is required in each tyre to
support the weight, the larger the tyres the less pressure is required and the more
tyres there are the less pressure is required. Remember, if pressures are too high
runways and taxi ways will be unable to support the load.
- -
So in general for large aircraft a landing gear will need a large tyre at a certain
pressure or several smaller tyres at the same pressure.
The actual configuration of the landing wheels will depend on the designer to cot
with the problems of stowage, safety, wheel loading and CBR.
Wheel loading can be reduced and CBR improved by have multi wheeled units
using twin tyres per landing unit; three wheels; four, six, eight or even twelve.
Some aircraft have many main wheel units (several each side of the fuselage) with
twin tyres on each so making u p to a considerable number of main wheels.
The advantages of a multi wheeled unit over a single wheeled unit are:
* Reduced wheel loading (though this will depend on other factors also).
* Easier to service. Although more complex the wheels are smaller and
easier to handle.
- 28 -
moodull l A-1228
* Easier to stow. Bogie units can be rotated, turned etc to reduce their
stowed volume. Some units are shortened by a shortening link within
the leg - though this could also apply to single wheeled units.
k
Greater safety factor. In the event of a tyre burst for example there
will still be one or more tyres remaining to take the load. Even so, on
any landing gear a tyre burst on landing can be critical.
A
Better braking. Each tyre is braking on its own piece of runway which
might have slightly different conditions to the next tyre so each is
braking a t its own best efficiency.
I
SINGLE WHEEL DOUBLE WHEEL BOGIE UNIT ( 4 , 8 OR 12 WHEELS
rnoodull l A-1229
Note the location of the nose wheel - off centre. For space reasons it h a d to retract
sideways a n d the additional stresses on the fuselage were found to be negligible
so it was fitted as shown.
Bogie Units
Normally confined to main landing gear units, the design of which can vary but i n
general, comprise a telescopic leg containing a shock absorber and a bogie beam
pin jointed at its connection to the shock absorber. This beam carries front a n d
rear axles for four or eight wheels (figure 18).Torque links between the main leg
and the beam or sliding portion prevent axial rotation of the unit whilst leaving it
free to slide u p and down.
rnoodull l A-1230
ATTACH ME^^
LEG MAIN
POINTS
I
6
-BRAKE
COMPENSATING
---. .-
LEVELLING
The beam may be in two parts connected via a bogie swivel hinge which allows
better articulation during a turn and the bogie pivot allows the beam to tilt -
usually with the rear wheels trailing down (but not always). This tilt may be
assisted by a bogie damper strut attached between the beam and the leg. This tilt
is sometimes called assisted articulation.
The beam is usually fitted with a micro switch which prevents retraction in the
event of incorrect tilt or articulation.
Figure 19 shows an example of how the bogie can be rotated to, in this case, fit
into a wing section and figure 20 shows the main gear of the A300.
ATTACHMENT
TORQUE
w
Fig. 20 THEA300 MAIN GEAR
Theseiare fitted to absorb the shock of landing. Some shock i s absorbed by the
tyres $ producing pressure energy, but most of the shock is absorbed by the
shock absorbers. Some of the older units used springs or bungee cords to convert
the downward kinetic energy into strain energy. Most modern units convert this
energy into pressure energy (of a gas, or in some cases of an oil).
QUESTION The oleo works on converting the downward kinetic energy into
pressure energy within the oleo. What happens to the fonvard kinetic
energy of the aircraft? (5 mins)
The support of the static weight of the aircraft is achieved by the pressure within
the unit times the area of the unit's piston/cylinder giving a force that is equal
and opposite to the downward force of the aircraft on that landing gear unit.
With the liquid spring type the energy of landing is absorbed by the increase in
pressure and the compression of the fluid within the unit. Control of recoil is by
controlling the rate of fluid flow passed a piston.
- -. --
With the other two types the landing shock is absorbed by the increase in
pressure and the compression oflthe gas. Recoil control is carried out by
controlling the rate of fluid flow through a piston.
--
ANSWER If the recoil was not &ontrolledthe pent-up e n e r q i n the form of very
high pressure within the unit would cause the oleo to extend quickly
and bounce the aircraft back u p into the air -just like a bouncing
- -b&ll. Not what is required;-In general terms the unit will collapse
-
quicker than it is allowed to extend. - -
Each oleo consists of an inner tubular or solid member, fitted with a piston,
telescoping into a n outer tubular member. With the aircraft on the ground the leg
telescopes sufficiently to create enough pressure which supports the static weight
of the aircraft.
When the aircraft becomes airborne, its weight is transferred to the mainplanes
and the oleo fully extends. When the aircraft lands the downward energy of the
aircraft telescopes the oleo which absorbs the shock of landing.
THE LIQUID SPRING OLEO
The unitflEonsistsof a thick walled cylinder (to withstand the very considerable
press&-es that are built up) hoqsing a piston with a large diameter piston rod
(figure 2 1).
I
These jv<ry high pressures are diffcult to contain with conventional seals (around
the pistdn rod) so a special high pressure gland assembly is used. The idea behind
the gl&d assembly is to control the friction between the gland and tlie piston rod
whilstistill keeping a fluid tight joint. It achieves this by progressively increasing
the seal pressurec'on the rod as the pressure rises.
On lahdini-the piston is caused to enter further into the cylinder reducing its
intekGalalvolume by the amount of piston rod that enters. This compresses the
fluid and raises its pressure. During compression the valve (flutter plate) is open
(figures 2 1 and 22) and fluid passes reasonably freely across the piston head.
On rebound the piston moves out of the cylinder and the valve/flutter plate
closes. This reduces the number of holes that the fluid can pass through so the
rate of piston movement is reduced.
QUESTION When the piston gets to the end of its travel a t its maximum collapse
position during landing what are the pressures either side of the
piston? (2 mins)
ANSWER They are the same. The pressures are very high but they are the
same.
QUESTION If the pressures are the same on both sides of the piston what makes
it extend? (5 mins)
ANSWER A force will make it extend and pressure times area produces a force.
The area on the rod side of the piston is smaller than the area on the
other side (smaller by the amount that is taken u p by the rod) so
there is a greater force pushing it out than that trying to push it in.
L -- - - -
- /
,
Maintenance
PISTON MOVEMENT
PISTON MOVEMENT
TER CYLINDER
HIGH PRESSURE
GLAND ASSEMBLY FLUTTERPLATESTOP
FLUTTERPLATE
PISTON HEAD
FLUTTER PLATE
REDUCEDRETURN (CLOSED)
FLUID FLOW
FLUID PRESSURE
INCREASING CONSIDERABLY
AND FLUID COMPRESSING
- -
WHEEL END OF UNlT
3. Connect the flexible charging hose of the universal charging gun (or
similar) to the oleo charging valve. Release the oleo pressure slowly.
4. Bleed the oleo my pumping fluid until there is an air free flow from
the bleeder plug.
5. Collapse the unit by placing a bottle jack under the landing gear and
pumping up. This will expel fluid (to be collected in a suitable
container) and ensure free movement of the oleo to the limit of its
range. Tighten the plug.
5. Slowly pressurise the oleo, at the same time lowing the bottle jack.
The oleo will extend to its fullest extent. Continue charging to the
pressure specified in the AMM. {As an example 1700psi (2.7MPa))
6. Disconnect the charging gun. Check for leaks from the oleo charging
valve, the sliding portion (gland assembly) and fit dust cap.
No leakage is permitted and if found the unit must be changed, or if allowed the
offending part (for example the charging valve) is replaced in-situ (on the aircraft).
In some cases the AMM calls for a 'scragging test'. This involves repeated collapse
and extension of the oleo and checking each time that full extension is achieved
every time. A duration test may also be called for which involves the unit being
kept collapsed for a period of time and then released to check for full extension.
WARNING. Charged oleos are dangerous. Before attempting to carry out any
dismantling the pressures must be relieved.
Faults
Excessive deflection.
--,\
Lobs,of pressure. Find ldakls - & t i 3
Loss of oil. ' and re+charge.
!
Slow response to Check ,reasons '
deyction but rectify !and-re-dh&rge.
smooth operation. -- --/'
I1 ' >
Slow response to ~ d , nor
t damAge1d Replace $nit.
deflection 'and piston rod. ', i
erratic movement. -- i _- '
This unit has two mediums (gas - usually nitrogen and oil - say DTD 585) and
each has its own roll to play. In general terms the gas absorbs the energy by
compressing and the oil controls the recoil. The oil is at about the same pressure
as the gas most of the time but, because it does not work at such high pressures
a s the liquid spring type unit, the oil does not compress very much - its job is just
as a controlling medium.
QUESTION Air will do the job just as well as nitrogen and is significantly cheaper,
so why use nitrogen? (5 mins)
- 37 -
rnoodull l A-1237
ANSWER Nitrogen will not support combustion - air will. It is possible to
imagine the compression of the air on landing. I t will be an adiabatic
compression so the air will get hot. Should a small quantity of oil be
present then there is t h e same situation in the cylinder of the oleo
that occurs in the cylinder of a diesel engine. BANG we couId have
trouble. Called dieseling and would not occur if the gas was nitrogen.
The drawing shows torque links preventing axial rotation of the inner cylinder
within the outer cylinder. There are seals around the floating piston and between
the inner and outer cylinders.
T h e ~ eare qil filler plugs in the top of the ,unit (oil head) and,a,gas
,chargingvalve
at thzibofbn of the inner cyliiider;- - -- - - - - - .
I I , : , ,
! ! , ,
!: ,,
MAIN
OlL
STRUCTURE
CY UNDER:
mmn A'
SEPARATOR
SEALS
GAS CHARGING
VALVE \
With the weight of the aircraft off the unit the gas pressure forces the separator to
the top of its cylinder forcing all the oil into the top of the unit and extending the
unit fully. In this condition the oil is a t little or no pressure and the gas is a t its
normal charge pressure (say 1200psi - 1.9MPa).
On the landing stroke the downward energy collapses the unit forcing the inner
cylinder and piston head upwards. This causes the oil to pass through all the
ports in the piston head and force the separator down. This causes the gas to
compress and the pressure to rise (the pressure rises in both the oil and the gas
but the oil volume changes little). The compression of the gas absorbs the shock
of landing converting it to pressure energy and hence heat energy.
WITH
.UME
At the end of the compression stroke when all the energy has been converted/
absorbed, the pressure in the unit is greater than that required to support the
static weight of the aircraft and the unit will want to extend rapidly. But this must
not happen. As the unit extends (recoils)the fluid flows back through the piston
and in doing so the flutter plate closes (assisted by a spring). This restricts the
flow of fluid to a limited number of holes and permits a comparatively slow rate of
oleo extension - thus recoil is controlled.
After landing the static weight of the aircraft is supported by the unit when it has
collapsed sufficiently so the internal pressure is enough to just balance the weight
of the aircraft acting through that leg.
rnoodull l A-1239
Maintenance
As always consult the AMM first, but in general the maintenance procedures are
not too unlike that for the liquid spring oleo. The charging and topping up
procedures, however, are different.
Periodically the unit will need topping up with nitrogen, but it is important that
the oil quantity is correct before doing this. If there is any doubt the oil quantity
must be checked before attempting to charge the gas pressure.
Provided the AMM says so this may be carried out with the aircraft's weight on t h e
wheels. The procedure is as follows:
Remove the other filler plug (plug 2) and pump in oil until an air free
flow of oil comes out (bleeding).Refit plug 2.
Remove the charging gun and refit plug 1. This now leaves the unit
full of oil to the correct specification, free of any air, the oil un-
pressurised and the floating piston at the bottom of its travel.
-Connect an adapter (Turner-gauge)to the nitrogen charging valve a n d
charge with nitrogen. The leg will extend and the aircraft will rise.
Refer to a pressure/extension graph for the correct amount of
extension required (example figure 26). This graph will be in the AMM
and possibly on a plate riveted to the landing gear.
Check for leaks, wire lock the plugs, record the work done and sign
the appropriate documentation.
If the process cannot be done with the aircraft on the wheels then it must be
jacked and the following procedure carried out:
Note. In this condition when the unit is fully extended the oil pressure is about
zero and the gas pressure is normal charging pressure.
QUESTION Why is it so important when using a bottle jack not to lift the aircraft
off its main jacks - after-all, surely it could be put back easily by just
lowering the bottle jack and the aircraft would settle back on its main
I
jacking points again?
-.
I - --- -
I \ \\, II - --,'
I \
I I
Fault Symptoms,
I
/ 1
-Symptoms Probable-e'aqses Remedy ,
-
- ---
Insufficient deflection. Gas pressure too high. Check gas pressure and
rectify.
Harsh action. Oil quantity too high. Check level and rectify.
- 41 -
rnoodull l A-1241
Notes. 1. Some seals on some oleos can be changed whilst the unit is still
fitted to the aircraft (in-situ)- check the AMM.
2. Some scratches and slight damage to the sliding portion of the unit
may be dressed out (blended out) in-situ. The depth and length of the
dressing out is limited - refer to the AMM.
3 . On some civil aircraft an oleo is used which is essentially one oleo
within another with two floating pistons and two gas chambers and
two oil chambers. One set (oil/gas/floating piston) is a low pressure
unit and the other is a high pressure unit. The idea is that when the
aircraft lands the oleo is so designed so the high pressure set
operates to absorb the shock and when the aircraft taxies it moves on
the low pressure set, so giving a more comfortable ride for the
passengers. Not a common unit - for costs reasons.
This -type of unit is more popular with civil aircraft manufacturers. It is because lL
is simpler-ivith no separator. Without a separator there is a oil/gas interface and
the gas must be a t the top with the oil underneath.
I
I t consists of one sliding member inside another, with the inner member having a
restrictor head. A centre rod or metering tube slides within the restrictor head. On
some units the centre rod is tapered with no fluid port in the middle. The taper
g v e s a progressive deceleration of the unit as it collapses as less oil is able to
squeeze past the rod.
The centre tube of the unit shown is used to brake the end of the oleo's extension
after take-off. Total travel for the shock absorber is 17.7 inches (45mm).
Valves are fitted (main valve and restrictor valve in the drawing) to control recoil.
These allow a reasonably fast collapse of the unit on landing but close to control
the rate of extension on recoil.
With the weight of the aircraft off the leg the gas pressure for& down & , t h e oil
which fully extends the unit. On 'lahding the h i t is caused t o telescope w'hich
forces fluid from the bottom chamber to the top. The fluid will:pass through the
port in the centre rod and through ,bzhppen restrictor valvesi ~ 0 t h - t h fluid
e and
gas will increase in pressure witd the gas compressing in volume- this absorbs
1
the shock. !
,, I I
I ' I I
I I
On recoil the fluid is pushed by the gas downwards to move into the bottom of the
unit. This will cause both restrictor valves to hose and f l u i d ~ a nonly pass
thro&h-the-small holes in the buter-restri6tor valve and the the centre rod
- thus recoil is controlled.
In the static weight condition the internal pressure times the circular internal
area of the unit equals the weight acting through that undercarriage leg.
Maintenance
The unit is of the direct nitrogen fluid contact type and is filled with oil and
nitrogen through one common filling and charging valve. This is located a t the top
of the unit and is connected to a short stack pipe which automatically limits the
amount of oil that can be in.
Ramp servicing is limited to visual inspection for damage, leaks and correct
extension.
Oil level is checked with the unit collapsed. The aircraft's weight can be on the
wheels or the aircraft can be jacked and a bottle jack used.
After the oil level has been topped up to the bottom of the stack pipe the unit is
charged with nitrogen.
SERVICING CHART
AMORTISSEUR
blank
SHOCK
.--- - - - -
SPHERICAL
BEARING
i i
1. Carry out the same precautions a s with the gas/oil oleo with
separator.
2. Deflate. Connect a selector valve and pressure hose to the filling and
charging valve. Open the valve and release the pressure until the oleo
rests against its inner stop. Check extension (dead travel 34mm).
3. Oil Chargng. Connect the oil pump (filled with the correct
specification oil - a s per AMM/data plate) to the selector and charge
the oleo with oil to raise it by 20mm. Check the new dimension is
54mm.
4. Bleed. Wait 1 minute. Open the selector and release the fluid allowing
the unit to settle on its inner stop again. Check fluid for bubbles. If
necessary repeat steps 3 and 4.
- 45 -
rnoodull l A-1245
' 3 1. DEFLATE
Fig. 28 DEFLATION
,I -
2. OIL CHARGING
- 46 -
moodull lA-1246
3. BLEED
Fig. 30 BLEEDING
- -- - -
Fig. 3 1 PRESSURISING
- 47 -
rnoodull l A-1247
, Fig. 32 OLEO DATA PLATE
SERVICING EQUIPMENT
The AMM will specify the equipmeritpto be used. In some cases it will be "special to
type" and supplied by the aircraft manufacturer, in others the equipment will be
standard equipment. In the case of standard equipment the aircraft manufacturer
will specify the requirements the equipment has to meet - such as threat adapter
sizes, pressure requirements, fluid flow rates etc. What follows is a description of
some_"standard equipments".
This hand held gun is used to charge liquid spring and gas/oil oleos with oil. It
consists of an adapter block fitted with a Bourdon tube type pressure gauge, a
non-return valve, a bleeder screw and a flexible hose - one end of which connects
to the equipment to be charged. The other end connects to the gun itself.
The gun is filled with the fluid to be pumped and the banjo union is screwed
directly into the charging valve of the oleo to be charged (after removing the dust
cap).
Before use fill the gun with the specified oil then proceed as follows:
1. Screw the flexible charging hose onto the adapter block and screw the
adapter block onto the charging gun.
- 48 -
moodull l A-1248
2. Ensure the bleeder screw is screwed down and prime the flexible hose
by pumping the handle until an air free flow emerges.
3. Remove d u s t caps of banjo union and oleo and screw banjo union to
charging valve. Do not tighten fully.
4. Pump fluid to issue from the loose connection and tighten connection
a t the same time. This ensures that there is no air in the charging
hose.
5. Operate handle to pump fluid into oleo noting the pressure on the
gauge. If oleo charging valve not of the non-return type slacken to
allow pumping.
6. When charging is complete tighten oleo charging valve (not of the
non-return valve type), release pressure in the charging hose by
slackening the bleeder screw. Remove hose.
7. Fit dust caps. Lock wire as appropriate.
PRESSURE GAUGE
' I
~ .-
.
CYLINDER CONTAINING
FLUID TO BE PUMPED
Inflation Adapter
Used when inflating components with gas and also used for deflation, pressure
checking etc. Is fitted with a control valve to control the rate of inflation and a
pressure gauge. Is also fitted with a pressure release valve. It has an adapter on
one end to connect to the high pressure hose from the nitrogen charging trolley
and an adapter on the other to connect to the oleo.
moodull lA-1249
High Pressure Nitrogen Charging Trolley
May have two wheels and fitted with one high pressure nitrogen bottle. May be a
four wheeled trolley with four bottles and provision made for towing. Controls are
provided for reducing the bottle pressure and for regulating the flow. Pressure
gauges are provided to monitor the bottle pressure (fully charged normally
4500psi) and the reduced supply line pressure. It is important to note that when
charging this line pressure gauge reading should correspond to the adapter gauge
reading on the component.
The controls on the trolley can be set to reduce the bottle pressure down to the
line pressure required for the component.
To charge an oleo the adapter is connected to the oleo charging valve and the hose
from the high pressure nitrogen charging trolley is attached to the adapter. The
trolley controls are set to OFF. The bottle key is inserted into the end of one
nitrogen bottle and it is turned ON. The first gauge on the trolley controls will
show bottle pressure (say 4500psi). The trolley regulator valve i s adjusted to give
the korrect line pressure to the component (say 1200psi) - shown on the second
gauge 'on the trolley. When correct the third valve is opened to supply this
pressure to the adapter on the oleo. The gauge reading on the adapter should be
the same as the second gauge on the trolley.
I I
CONTENTS
Page
Tyres
Tyre wear
Markings
Pressures
Inspection
Mounting tyres
Inflation
storake
Inner thbes
Wheels I
Inspection
Brakes
Drum brakes
Disk brakes
Skid cont!rol ,
Mechanical &ti skid
Electron$ anti skid
-A320-system
--B767-
AIRCRAFT TYRES
Until recently these were usually of cross-ply construction. However, radials are
becoming more popular as they offer a reduction in weight with increased
landings.
The cross-ply tyre is made u p of plies of weftless nylon fabric, each ply laid on the
bias and a t 90' to the previous ply.
The radial tyre is made u p of weftless plies aB laid radially across the tyre one
upon the other.
JAR25 states the requirements that a tyre has to meet, in particular the
downward and forward loads in terrns of "g" and relate to main wheels, nose
wheels and single and multi wheeled units. Tyres must have an approved speed
and load-rating and have sufficient-clearance when retractep-to-aUow..for tyre
growth: Tyre growth is the incrkase-in-size of the tyre due to-centrifug&forces a t
high speed. 1 :
I
I
II
/
I
I
I
I
I
I
I
I i I
I
1
1 I I
Cross ply Construction - - I I
--
--I\ I
Sidekall~~protectiv layer
e of flexib1e;wezdher-resistance nhttural-rubber covering
The outer carcass ply, extending from tread edge to bead area.
Tread Reinforcement. One or more layers of nylon fabric that strengthen and
stabilise the thread area for high-speed operation. Also serves as a reference for
the buffing process during the re-treading of tyres.
Breakers. Reinforcing plies of nylon or Ararnid fibre placed under the tread rubber
to protect carcass plies and strengthen and stabilise the tread area. They are
considered an integral part of the carcass construction.
Beads. High tensile copper-coated steel wires embedded in rubber, the beads
anchor the carcass plies and provide a firm-mounting surface to the wheel.
- 1 -
rnoodulll A-1252
TREAD PATTER
REINFORCING
RUBBER LINER
TUBELESS TYRES
- - -- STRIPS
Apex Strip. A wedge of rubber affmed to the top of the bead bundle, serving as a
filler.
Flippers. These layers of rubberised fabric help anchor the bead wires to the
carcass and improve the durability of the tyre.
Chafers. Protective layer of rubber and/or fabric located between the carcass plies
and the wheel to prevent chafing.
I i
~ iaBADWL
~ .
.
TYRE \
1
I
--_. , -
I \ '\ ,
I i --
Bead Toe? The inner bead edge ciosest to the tyre centre line.
; I / ' I
I g' e .
Bead Heel. The, outer bead edge $hat fits ag&st the wheel f l ~
- , ,
- -' \ -
Fitting Lines. Lines moulded around the lower sidewall to check for concentricity
of tyre to wheel.
Radial Construction
The basic difference between a cross-ply tyre and a radial tyre is the lay of the
plies within the tyre carcass. A s stated previously, the plies are laid radially
across the tyre, but the remainder of the tyre is very similar in construction to a
cross-ply tyre.
rnoodull l A-1254
INNER
LINER
SIDE
WIRE :BEADS
~ a d i atyres
l feature a rigid belt Bnd a flexible carcass, providing a n increase in the
number of landings and a reduction in rolling resistance. The efficient use of high
strenhh materials results in a lighter weight tyre with improved performance.
Tread-Patterns
Ribbed (ie circumferentially grooved) treaded tyres are probably used more than
any other and there are a number of variations on the basic pattern such as the
number of ribs and the width of grooves. A ribbed tread provides a good
combination of long tread wear (long tyre life) and good traction and directional
stability, particularly on hard surfaced runways.
Diamond pattern (or 'all-weather') tyres are also used and give good performance
on all types of surfaces. They are particularly suitable for unpaved (eg turf or
packed earth) airfields.
-4-
rnoodull l A-1255
The plain tread (smooth tyre) was common at one time, particularly on British
aircraft, but h a s gradually been replaced by ribbed and diamond pattern treads.
I t is, however, still used on some older fixed wing aircraft.
Some nose wheel tyres are fitted with a water deflector (or 'chine') on the upper
sidewall, to deflect water away from rear-mounted engines when landing/taking
off on/from wet runways. This deflector may be on one side for twin-wheel
installations or on both sides for single-wheel installations.
Water dispersing treads, which have many small holes incorporated in the crown
and shoulder rubber, are also fairly common as a means of helping to prevent
aquaplaning.
-
SINGLE
CHINE NRE
I - !
-1
I
TYRES 1
ANSWER: It is a condition where the tyre is travelling along a wet runway so fast
that the water has not got time to be moved out of the way by the tyre
tread (normally a sort of 'squeezy' action). This means that a thin film
of water gets in between the runway surface a n d the tyre reducing the
grip so much that the effect is similar to being on sheet ice.
Aquaplaning is a function of speed, standing water depth, aircraft
weight and tyre tread pattern (a smooth tyre aquaplanes at a slower
speed than a patterned tyre).
TYRE WEAR
-5 -
moodull l A-1256
Tyres with Marker Tie Bars
Some rib pattern tyres embody equispaced marker tie bars in the groove
designated for use a s a wear indicator. The limit of wear is reached when the tie
bar is worn to the base of the groove which contains it.
-
1
. -
Tyres Without
- - --
Tread Reinforcement
-
Assessment of tread war on these tyres must be based on using the centre groove
as a wear-indicating groove. If the tread pattern does not incorporate a centre
groove, use the grooves outside the centre rib. The tyre is worn to its limit when
the tread is worn to the base of the wear indicator groove.
WEAR INDICATOR GROOVEIS
Identified by the letters DRR in the Code Panel and the words REINFORCED
TREAD on the sidewall. They may or may not have marker tie bars. The limit of
t h e wear is reached when the depth of the wear-indicating groove is reduced to
2mm. If the wear is not even, the tyre must be discarded when a total of 25% of
the groove circumference is reduced to 2mm depth, irrespective of the depth of the
remainder of the groove. Tyres thus worn must be withdrawn from service for
possible remoulding.
A i r Worthiness Notice
AWN number 5 states that wear indicators must be fitted that indicate when wear
h a s occurred that impairs wet braking efficiency. This must be part of the
certification process for the tyre.
i
\ 7-- .--. - - ---
\ ', I
* If the tread h a s worn to less than:2mrn across the entire width of the
treadjin contact with the r u n ~ a y ~any
a t place on ithk circumference.
-- /'
/
-
- \-I
~ o r n e ~ i a t i o n s - k abey allowed, eg if-one$roove is less than- 2mm and the others
are 3mm or more.
These have two points of contact with the runway either side of the crown. Not in
common use and were designed to reduce the problem of shimmy. Fitted to nose
wheels only.
Can remain in service until the centre of the crown shows signs of having been in
contact with the ground. (The centre of the tyre between the contacts can be as
high as 25mm from the ground on a new tyre).
Helicopter Tyres
Are fit for further service when they contain tread cuts, which expose but do not
penetrate the casing plies, irrespective of the number or size of cuts.
moodull l A-1258
Chinned Tyres
(a) A crack deeper than 0.4mm and exceeding 25.4mm (1.0 inch) in
length.
1
I
LOAD RATING - -
TUBLESS APPICABLE
SPECIFICATION
APPLICABLE
SKID 8 SPEED
RATING
TREAD CODE
-8-
rnoodull l A-1259
Tyre Markings
All commercial aircraft tyres approved under FAA Test Requirement TSO-C62c
(AWN 93 refers) are marked clearly with the following minimum information:
Manufacturer's name
Size
Load Rating
Speed Rating. (Air Worthiness Notice 93 states high speed tyres as
rated a t above 160mph.)
Skid Depth
Manufacturer's Part Number
Serial Number
Manufacturer plant identification along with the TSO marking.
r In addition, Goodyear tyres are marked with the ply rating and other marhngs as
t requiredb?
I airframe manufacturers-or other
-.. organisations.i __ - ,
-.
-\ ' -
Military tyres carry markings required by the,appropriate militaky s6Scification.
I
1
In addition, the Association of European Ajrljhes (AEA) requires an AEA code
;
which defines both tyre carcass h d tread cpnstruction. 1 1 I
--- \.. -- /
'b'
-
All retread t v e s carry the symbql or tf$e,dprd 'RETREAD'. i It also ifidicates the
number of times $he.tyre has been retreaded :(Sometyres are\rk-treaded many
times).
Tyre sixes are usually identified by three dimensions, eg 26 x 7.55 - 13. The
markings are in inches but the inch mark is not shown. If the size is in
millimetres then the symbol mm is used.
NOTE. When only two figures are given it is the first figure, the overall diameter of
the tyre that is omitted.
Serial Number
Moulded into the tyre wall to identify a particular tyre. Each tyre will have its own
unique serial number to identify it against its records.
SERIAL NUM
EQUIPMENT
IDENTIFICATION
TYPE NUMBE
DGAC STANDARD
FAA STANDARD
MOLDED SKID
I
PART NUMBER SPEED RATING
AEA CODES
Date of Manufacturer
Tyre Pressures
Range from 25 to 350psi gauge pressure. Always consult the AMM. Pressures may
be given in psi, bar or kPa. Tyres with greater than 100psi pressure are
considered to be high-pressure tyres.
Notes
2. 14.5psi=lbar
lpsi = 6894Pa
3. Pa = Pascal
Conductivity
I
I -,
Some tyres are qianufactured wilh; tread rubber with conduc$ng compounds to
I
permit ea'rthing of static charges!. Wsually nose and tail w h e e l ~ ~ are
e s conducting
and have markings to indicate this such as a lightening strik,e symbol or the word
"conducting".- - - -- --
Regular inspection of tyres is recommended for safety and tyre economy. The
frequency of the inspection should be determined by the use and normal tyre
wear of the particular aircraft involved and is specified in the maintenance
schedule. With most aircraft, tyre inspection after every landing, or at every
turnaround, is required. With all aircraft, a thorough inspection (usually in the
bay) is advisable after a heavy or overweight landing.
Tread Wear
Tyres should be removed when tread has worn to the base of any groove a t any
spot, or to a minimum depth as specified in the AMM or tyre manufacturer's
manual. Tyres worn to fabric in the tread area should be removed regardless of
the tread remaining.
moodull l A-1262
Uneven Wear
If tread wear is excessive on one side, the tyre can be removed from the wheel and
turned around, providing there is no exposed fabric. Gear misalignment causing
this condition should be corrected.
Cuts
To check for depth of cuts the cut must be probed by a tool something like a n ice
pick. This requires considerable sideways force to prize the rubber to one side to
see the bottom of the cut. Once the bottom of the cut can be seen the plies can be
checked for damaged and the area can be checked for foreign objects.
I
Bulges -- .
Bulges in any part of tyre tread; sidewall or bead areas, indicate a separation of
the plies or damaged tyre. Mark the area with a crayon and remove the tyre.
1
Flat spots
Generally speaking, tyres need not be removed because of flat spots due to side o r
hydroplane burns unless fabric is exposed. If excessive unbalance results,
however, remove the tyre.
Beads
Inspect bead areas next to the wheel flanges for damage due to excessive heat -
especially if brake drag or severe braking has been reported during taxi, take-off
or landing.
INFLATION PRESSURES
Keeping aircraft tyres a t their correct inflation pressures is the most important
factor in any maintenance program. The problems caused by under inflation can
be particularly severe. Under-inflation produces uneven tread wear and shortens
tyre life due to of excessive flex heating. Over inflation can cause uneven tread
wear (in the centre of the crown), reduced traction, makes the tread more
susceptible to cutting and increases stress on the aircraft wheels.
The inflation pressure as stated in-the AMM should be used for each-tyre. I t must
be determined if loaded' or 'unloaded~infl&ionpressure hak+beenspe?ified.
I 1 ' , I
I '
4
When t$re i s under load, the q r chamber volume is reduced due to tyr;
deflection. Therefore if unloaded pressure has been specified; that pre&sure
should be increased by 4% to obtain the- ehuivalent loaded inflation presiure.
~ d j u s t i n dfor Temperature
The minimum required inflation must be maintained at the cooler climate and the
pressure can be adjusted in the wanner climate. An allowance must be made for
the inflation drop in the cooler climate. An ambient temperature change of 5°F or
3°C produces approximately a 1% tyre pressure charge.
NOTE. Excess inflation pressure should never be bled off from hot tyres. All
adjustments to inflation pressure should be performed on tyres cooled to ambient
temperature.
- 13 -
rnoodull l A-1264
Cold Pressure Setting
NOTE. Any tyre removed because of low inflation pressure should be inspected by
an authorised re-treader to verify that the carcass has not sustained internal
degradation. If it has, the tyre should be scrapped.
A tube-type tyre that has been freshly mounted and installed should be closely
monitored during the first week of operation, ideally before every takeoff. Air
trapped between the tyre and the tube a t the time of mounting could seep out
under the beads, through sidewall vents or around the valve stem, resulting in an
under-inflated assembly.
- 14 -
rnoodull l A-1265
MOUNTED TUBELESS TYRES
A slight amount of diffusion through the carcass in tubeless tyres is normal. The
sidewalls are purposely vented in the lower sidewall area to bleed off trapped air,
preventing separation or blisters. A tyre can lose as much as 5% of the initial
inflation pressure in a 24-hour period and still be considered normal.
NYLON STRETCH
The initial stretch or growth of a new nylon tyre results in a pressure drop after
mounting. Consequently, nylon tyres should not be placed in service until they
have been inflated a minimum of 12 hours, the pressures re-checked and tyres
re-inflated if necessary.
Nylon tyres on aircraft left statiorary for &$length of time d l 1 develop temporary
flat spots, The degree of this flat-spotting d e p ~ n d on
s the load, tyre defledtion and
ternperathe. Flat-spotting is more 'severe and more difficult t& work odt during
cold wesather.Moving a station+ @craft regularly will lessen this condition. If
possible, a n aircraft parked for longj%Gods (30 days or more)/should be jacked
u p to remove the weight from the tyre;under normal conditions,-a fldt spot will
disappem by the end of the taxi h n . i
1
1 '
1 I
I I '
I I
1 I
1. Use new O-ring seals with best cold weather properties, properly
lubricated and installed.
4. Aircraft parked and exposed to cold soak for a period of time (1 hour or
more), should have tyre pressure checked and adjusted accordingly.
Tyres will have taken a nylon 'set' and experienced a pressure drop.
Tyres subjected to above normal braking energies during a n RTO (Rejected Take-
off) should be removed and scrapped. Even though visual inspection may show
no apparent damage, tyres may have sustained internal structural damage that
could result in premature failure. Also, all wheels must be checked in accordance
with the applicable Wheel Overhaul or AMM after a n RTO.
When new and/or re-treaded tyres are installed on the same landing gear axle,
the diameters should be matched within the Tyre and Rim Association inflated
dimensional tolerances for new and grown tyres.
Tyres 'should be kept clean and .free of contaminants such as oil, brake fluid,
grease, far and degreasing agents which have a deteriorating effect on rubber.
Contaminants should be wiped off with alcohol, then tyres washed with soap and
water immediately. When aircraft are being serviced, tyres should be covered.
1 -- --
Aircraft kyres, like other rubber products, are affected to some degree by sunlight
and egremes of weather. While weather-checking does not impair performance, it
can be reduced by protective covers. These covers (ideally with light colour or
aluminised surface to reflect sunlight) should be placed over the tyres when an
aircraft is-tied down outside.
- ---
These areas should be kept clean of stones, tools, bolts, rivets and other foreign
materials at all times. With care and caution in the hangars and around the
airfield, tyre damage can be minimised and ingestion damage to engnes can be
reduced.
MOUNTING PROCEDURES
Deflate all tyres before wheel disassembly. A clip-on chuck, an extension hose
and a safety cage are recommended for inflation. A direct reading or dial tyre
pressure gauge should be used. Use of excessive air pressure to seat beads can
cause failure and result in serious injury.
TUBELESS TYRES
1. Check for word 'Tubeless' on sidewall.
2. Make sure tyre is clean inside.
3. Inspect the wheel halves (split wheel, divided wheel, loose flange etc)
for damage and corrosion. Check all seals for security and damage
Inspect all fittings for security - inflation valve, drive blocks, fusible
plugs, bearings etc. Make sure that the "halves" of the wheel are the
correct halves and fit correctly oriented.
4. Inspect the tyre. Check that it is undamaged and within the wear
limits if a used tyre. Check that it is the correct tyre and is the correct
size.
5. Clean the bead base with a cloth darnpened with denatured alcohol.
6. Align red balance dot (light spot) on tyre with wheel valve or wheel
heavy point, if indicated on the wheel. Lower the tyre onto the first
halve of the wheel.
7. - Ensure that tyre fits first halve of wheel correctly
r
andglace second
halve on the top of-therfirst-->nsuring they mate, colrzcsyy
8. Be sure that wheel bolts are\pro$erly torqued as per the'iaheel
manufacturers i n s t r p d t i o n s / ~ ~ ~ . I
II
9. Inflate tyre to rated bressure using inflation gauge and s&ety cage.
10. Check for any obvious!signs of,&- leakage, partic)du-ly from the
valve. - --
I -\ --
11. After a 12-hour strejch perio'd; &-inflate to rated Fnflation/bressure.
', I ' I
I ' I I I 1
Air Retention Check I
1I
i /' ,
-
--
/
. - -- /
1 -
If pressure-has-dropped more chan-5%-in-tfie next 24 hours:-
TUBE TYPE
1. Check the mating tyre and tube are specified and correct for the
wheel-tyre assembly (size etc).
2. Inspect the wheel and tyre as for tubeless tyres. Inspect the tube also.
3. Clean inside of tyre and lubricate lightly with talcum powder.
4. Place tube in tyre and inflate to slightly round out the tube in the
tyre .
- 17-
rnoodull l A-1268
5. Align the yellow stripe on the tube (heavy spot) with red balance dot
on the tyre (light spot). Assume the tube valve is the heavy spot if no
stripe on the tube.
6. Move the hand around the inside of the tyre between tyre and tube to
ensure there are no creases in the tube.
7. Lower tyre and tube assembly onto first half of wheel, ensuring valve
stem lowers into wheel valve slot correctly.
8. Lower second half of wheel onto first half.
9. Fit wheel bolts and nuts and torque to wheel manufacturers
instructions/AMM before inflating.
10. Inflate tyre to rated pressure using safety cage.
11. Deflate to equalise stretch in the tube.
12. Re-inflate to rated pressure.
13. Check for obvious signs of leakage particularly the inflation valve.
Ensure that the sealing ring is free from deformation, permanent set, ageing and
general damage; lightly grease the sealing ring with silicone grease.
Stretch the sealing ring evenly on to the wheel and ensure that it seats correctly
in its groove. It is imperative, however, to ensure that the tyre beads do not
become contaminated with the grease. The clearance between thetyre beads and
the fitted wheel-sealing ring is adequate to avoid contamination if care is exercised
in fitting.
It is recommended that the tyre is fitted on the wheel with the 'red spot' of the tyre
lined u p with the valve location. (Early issue wheels may have a heavy spot
indicated by two concentric rings; such markings should be ignored). Ensure that
the sealing ring has not been disturbed and assemble the wheel.
moodull l A-1269
(b) Connect a suitable nitrogen* pressure supply to the valve and inflate
rapidly to spread the tyre walls against the flanges. Stop pressurising
once this condition is achieved. If a seal cannot be affected, stand the
assembly vertically and apply a circumferential load around the crown.
* Tyres inflated with air and subject to excessive heating due to braking action
can experience a chemical reaction releasing volatile gases. In the presence of
oxygen this can cause an explosion. AN70 (data now transferred to CAP747)
requires that tyres on aircraft over 5700kg with retractable landing gear should
be inflated with a suitable inert gas with oxygen levels no greater than 5% by
volume. Nitrogen is widely used.
(c) Disconnect the pressure line, allow to deflate and fit the appropriate
valve core using the relevant torque spanner.
(d) - For assemblies requiring inflation u p to 175psi (12.06 bars) inflate to the
--
(e) 'For assemblies requiridg pressures greater than 17sp;i, inflate 'the tyre
to a pressure of 1 4 0 ~ s i ( 1 0 . 3bars)
3 t h e n deflate completely. check that
the tyre beads are properly seated on the wheel flanbe8. If not, re-inflate
to 150psi and deflate c o m p l e t e l ~ . ~ ~ i n a if
llythe
, beads are -corrkctly
I__
seated, inflate the tyre slo%fly-t~to-wdqking pressure arkd fit th_e,valve cap.
1 '
I ', I -
(f-) 'After a period of time, the pressure may decrease dde to tyre stretch, and
'up to 10% can be regarped as normal.
-- -- --.-
With tyre and tube combinations, tread separation and blistering can be caused
by incorrect inflation procedure. This is due to air being trapped between the
tube and the tyre. This condition is normally caused by inflating the tube too
quickly. Any trapped air will find its way through the tyre casing and finally build
up between the outer casing and the tread or sidewall. The resultant blister is
easily detected on the sidewall but not on the tread. A leaking tube can cause the
same kind of defect. If a blister does appear a s a result of trapped air, it will
usually occur during the first 48 hours after inflation. If the blister is located in
the lower half of the sidewall and does not exceed l.Oin (25.4mm) in diameter,
relieve the blister by puncturing the rubber only with a sharp instrument (called
an awl) held parallel to the sidewall. If it is greater than 1.Oin or is located in the
upper half of the tyre, the tyre must be removed. Small ridges are moulded on all
high-pressure tubes to facilitate the escape of the trapped air and tubes without
such vent ridges must never be fitted in high-pressure tyres.
moodull l A-1270
(g After a period of time, the pressure may decrease due to tyre stretch, and
u p to 10% can be regarded as normal.
With tyre and tube combinations, tread separation and blistering can be caused
by incorrect inflation procedure. This is due to air being trapped between the
tube and the tyre. This condition is normally caused by inflating the tube too
quickly. Any trapped air will find its way through the tyre casing and finally build
u p between the outer casing and the tread or sidewall. The resultant blister is
easily detected on the sidewall but not on the tread. A leaking tube can cause the
same kind of defect. If a blister does appear as a result of trapped air, it will
usually occur during the first 48 hours after inflation. If the blister is located in
the lower half of the sidewall and does not exceed l.Oin (25.4mm) in diameter,
relieve the blister by puncturing the rubber only with a sharp instrument (called
an awl) held parallel to the sidewall. If it is greater than 1.Oin or is located in the
upper half of the tyre, the tyre must be removed. Small ridges are moulded on all
high-pressure tubes to facilitate the escape of the trapped air and tubes without
such vent ridges must never be fitted in high-pressure tyres.
Types,up to 175psi -
3. Check that the tube inflation valve is lined up, not under stress and
-- seated correctly.
After servicing operations that involve tyre deflation, wheel assemblies must be
tested iaw the relevant instructions. These tests include a duration pressure test,
when the assembly is allowed to stand inflated for a period of 12 hours during
which period checks are made on the pressure. An immersion test (in water) can
be carried out when time does not permit the duration test. (The bearings must
not be submerged).
(Tyre pressures are given for cold tyres based on ambient conditions of 20°C
[63"F]. Should the ambient temperature rise to 23°C (73°F)it will increase the
pressure by about I%.)
CREEP MARKS
The purpose of creep marks are to indicate circumferential movement of the tyre
relative to the wheel. After the initial movement of tyre to wheel caused by the
landing (dependent on tyre load, inflation pressure, degree of braking, shimmy on
noseltail wheels, speed of landing etc) any subsequent movement of the tyre
around the wheel takes place at a much reduced rate, which if allowed to
continue beyond a certain limit, can, on a tyre and tube combination, result in
the valve stem being t o m from the tube - and total deflation. Hence creep marks
are painted i n white on the sidewall of a newly fitted tyre and over on to the wheel
flange. The width of the mark represents the maximum permissible tyre creep
and when the paint marks on the tyre and the wheel flange become misaligned by
the full width of the mark, the wheel must be removed from the aircraft for bay
servicing.
-- - --
-1
All tubeless-tyres, 8-ply rating and above; fiave been ventedLthe' lower sidewall
area. These vents prevent separation by relieving pressure build-up in the
. carcass plies and under the sidewall rubber. These vent holes (marked by green
coloured dots) will not cause undue air loss. Covering them with water or a soap
solution may show a n intermittent bubbling, which is normal.
When no leaks can be found on the prior checks, an air retention test must be
performed. The tyre should be inflated to operating pressure for a t least 12 hours
before starting the test.
This allows sufficient time for the casing to stretch, but can result in apparent air
loss. The tyre must be re-inflated after the stretch period to operating pressure.
Allow the tyre to stand a t constant temperature for a 24 hours period and recheck
the pressure. A small mount of diffusion is considered normal. However, an
inflation pressure drop of more than 5% of operating pressure indicates excessive
vent leaking.
Since there are only two reasons for air loss in a tube-tyre, a hole in the tube or a
defective valve or valve core, finding an air leak is usually simple. As with a
tubeless tyre, the first step is to check the valve and replace the core if it is
defective. If the valve is air tight, demount the tyre from the wheel, remove the
tube, locate the leak (by immersion in water if necessary) and repair or replace the
tube.
When inspecting a tube to decide whether or not it is the cause of the leak use
only enough pressure to round out the tube. Excessive inflation strains splices
and-may cause fabric separation on reinforced tubes.
I
- - -
whenever possible, tyres should be stored vertically on tyre racks, kept in their
original wrappings, if wrapped. The surface of the tyre against which the weight of
the tyre rests should be flat and, if possible, 3 to 4 inches wide to minimise
distortion. Stacking of tyres is permissible. However, care must be used to
p e v e i t distortion of the tyres on the bottom of the stack. The maximum
recommended stacking height is:
Up to 40 inches
Over 40 inches u p to 49 inches
Over 49 inches
Tubes can also be stored in matching tyres. Tyres should be clean and dusted
with talcum powder with tubes inflated just enough to round them out.
Under no circumstances should tubes be hung over fittings, pegs or over any
object that mighty form a crease in the tube. Such a crease will eventually
produce a crack in the rubber.
Ideally, both new and re-treaded tyres should be stored in a cool, dry place out of
direct sunlight. Temperatures should be between 32°F (0°C) and 80°F (27°C).
Particular care should be taken to store tyres away from fluorescent lights,
electric motors, battery charges, electric welding equipment, electric generators
and similar equipment. They create ozone, which has a deteriorating effect on
rubber.
Tyres and tubes should be stored on the "first in first out" basis and records
should be kept detailing each item's part number, serial number, wheel fitted to,
tube fitted, aircraft fitted to, number of landings going on the aircraft, number of
landings coming off the aircraft etc. Records should cross refer to other
documents such as aircraft log books, J A R form 1 (to be known as EASA form 1)
etc.
Care should be taken that tyres do not come in contact with oil, gasoline, jet fuel,
hydraulic fluids or similar hydrocarbons. Rubber is attacked by these in varying
degrees. Be particularly careful not to stand or lay'tyres on floors that are covered
with these contaminants.
i --- -- --I -
I
\ \ I - I' I
1
I , INNER TUBES
I
;
I
I
I
-
- -- \-_-, ,
-
The manufacturer of an inner tube -is done by an extruding .process which forces a
compound of hot rubber through a circular die, thus producing a continuous
length of rubber tubing. The requisite length, according to the size of the tube
required, is cut off, the ends are then butt "welded" together and a valve is fitted.
The tube is placed in a mould, inflated and vulcanised, so producing a finished
tube to the required dimensions with all the markings on.
During braking, excessive heat is generated in some types of brake unit, which
could cause damage to the standard tube. Thus some tubes are manufactured
with a thickened base or reinforced base.
Size
The size indicated on the tube is the same size as indicated on the tyre.
Balance Mark
A red line or red dots indicates the heavy spot of the tube. Otherwise assume the
valve is the heavy spot.
Examination of Tubes
Tubes and tube base supports may be cleaned with a warm soapy wash prior to
examination and dried thoroughly. Slight creasing or surface cracking may be
disregarded. On fabric-based tubes, splits in the reinforcement area or minor
blisters in the rubber covering around the base of the valve stem, and small
pinholes may be ignored. Tube compound properties tend to deteriorate with age
and this i s often indicated by hardening of the rubber.
A method used in examination of tubes requires the marking of two parallel lines,
one-inch-apart, anywhere in the crown area of the tube and stretching the tube
until-the lines are approximately two inches apart. The stretched surface of the
rubber must then be examined.
If theie are no signs of cracking on the surface of the rubber and if, when
released, the tube assumes its original condition without evidence of permanent
set in tHe stretched area, then the tube can be considered serviceable.
I
NOTE'. Tubes which have been subjected to excessive heat are scrapped.
AWN 93 states that new wheels brought into service for transport category aircraft
as from December 31 1980 must comply with design standard TSO C26c.
While there are many different designs of wheel and sizes and weights vary, the
classification of wheels falls into four main headings:
2. Divided Wheel: The divided wheel comprises of either two half hubs
bolted together (two piece divided wheel) or a centrepiece with a half
h u b bolted either side (three piece divided wheel).
3. Loose Flange: The loose flange wheel has a single flange retained by a
_- lockring, either round, wedge shaped or a three-piece flange with the
' pieces bolted together. -
.'
\ -, - ,'
\ I \
~ i r c r a fwheels
t are made from alumiKtum &loy or magnesium alloy. Cast wheels,
after mladhining, are subjected to impre&ation with a bakelite solution, to prevent
air perkgating through the poro+slwheel. @oSt wheels these dabs are made from
aluminium alloy; 1 1 I 1 I
/ ,' I
Brakg drive blocks are either mqdel.integrd yith the wheel or,htied on after
casting. The centre of the wheel-is-machined to take the whgel-bd&ngs.
Similar to those fitted to most cars, bicycles and motorbikes. The centre of the
bead seat area is recessed to allow fitment and removal of the tyre. When easing
the bead of the tyre over the flange of the wheel (say at the 12 o'clock position) the
bead a t the 6 o'clock position is positioned in the wheel well.
As anyone who has ever changed a tyre will know - it is not easy. It is difficult to
change on a bicycle let alone a car or a n aeroplane. The bead coils are made of
high tensile steel and wound around many times, so they will not stretch and
forcing the bead over the wheel flange is a difficult task. This is why many wheels
have provision to "remove the flange" and bolt it back on once the tyre has been
fitted.
moodull l A-1276
BRAKE DRUM BI-METAL STEEL
BALL BEAR1
WHEEL
LOCATING COLLAR
COUNTERSUNK
- --
I---
Divided wheel
~ o n s i ~of
t dtwo half wheels rnatcied up and connected by bolts which pass
through the two halves. The bolts are fitted with self-locking nuts. There is a seal
between the two halves on tubeless wheels to prevent air leakage between the
halves. ' _ -
- - - - -
The wheel may not be exactly in two halves and one side might be bigger than the
other.
Wheels of this type are made with one flange integral with the wheel body and the
other a loose flange and machined to fit over the wheel rim on the other side. The
difference between the loose and detachable flange type is the method by which
the removable flange is secured. The loose flange is retained by a lockng device
(similar to a large circlip) on the wheel rim and the detachable flange is secured to
the wheel body by studs/bolts and nuts. A loose flange may be a single piece, or
consist of two or three pieces bolted together.
rnoodull lA-1277
'.
NYLOC NUT SEAL
\ BOLT
OIL SEAL
HOUSING
LOCATING
ROLLER
BEARING
--.,
.OUTER--,
ID~IVE '.
jBL0CKS i
1 I
i
Fig. 11 BIVIDED
l
-
. TYPE WHEEL
- \ i
- -
-,
,
I \
\ ' I
When the tyre is iGflated, the loose flange 4 o i e s outwards an&covers the
lockring, thus trapping it in the groove. This prevents disengagement of the ring,
which- is locked to the flange and wheelhim by the side of the tyre. For
addiiionalse~uritysome lockrings-are-joined at the ends by!a lo& plate and
screws after fitting.
WARNING. There have been serious injuries with incorrectly fitted loose flanges
coming off when the tyre is inflated. Always inflate a newly assembled wheel and
tyre in a cage and always double check the fitting of the loose flange, lockring and
any additional locking devices during assembly.
To prevent rotation of the single loose flange on the wheel rim, a locating collar on
the lockring engages in a recess in both the wheel rim and the flange. To prevent
possible disengagement of the lockring during tyre deflation a multi-piece flange
was designed.
The multi-piece flange may consist of two or three pieces, each bossed to
accommodate securing bolts. Each piece has a beading of semi-circular section
on its inner face. This engages in a corresponding groove in the wheel rim.
- 27 -
rnoodull l A-1278
Tubeless Wheels
Where these have loose or detachable flanges suitable "0" ring seals a r e fitted
between flange and wheel to prevent air leakage. The wheel is also fitted with a
fusible alloy plug, an inflation valve, no knurled flange (this would reduce the
sealing capability between tyre a n d wheel flange) and a sealed bead seat region to
prevent air leakage.
To prevent this most tubeless wheels have one or more fusible alloy plugs. These
plugs screw into the bead seat area of the wheel and are drilled to accommodate a
piston seal and fusible alloy plug. When excessive temperatures are generated the
alloy melts which allows the air pressure to blow the piston seal out. The tyre will
deflate safely.
Creep
In service the tyre has a tendency to rotate (creep) around the wheel. This creep,
if excessive, will cause damage to the tyre bead region and tear out the inflation
valve causing tyre deflation.
Creep can be kept to a minimum by correct inflation, but design methods can
include the following:
* Knurled flange. The inner face of the wheel flange is milled so that
the side pressure on the tyre locks the bead to the flange. Not on
tubeless wheels.
* Tapered bead seat. The wheel rim is tapered to increase its diameter
towards the flange. As the tyre is inflated and the bead moves
outwards towards the flange, so it is caused to form a tight fit with
the wheel.
-
-
-
- -, \
\ i
\ \
I /
Protective Treatments
All wheels are given a primary anti corrosive treatment followed by a paint
treatment. Other treatments are applied but the most popular primary treatments
are:
- 29 -
rnoodull lA-1280
INSPECTION OF WHEELS
Check wheels for damage. Wheels that are cracked or damaged should be taken
out of service for repair or replacement in accordance with the manufacturer's
instructions.
Valves
Before deflating and removing the tyre from the wheel, check the valve. Put a
drop of water on the end of the valve and watch for bubbles indicating escaping
gas. Tighten valve core if loose. Replace valve core if defective and repeat leak test.
Check the valve stem and its mounting for leaks with a soap solution. If a leak is
detected, the wheel must be dismantled and a new valve stem installed.
If the valve stem threads are damaged, stems can usually be re-threaded inside or
outside by the use of a valve repair tool without demounting the tyre. Make
certam that every vaive has a cap to prevent din, oii and moisture from damaging
the coke.:
, ,
I
I
Fusible Plug
I
- --
The fdsible plug may also be defettive or improperly installed. Use a soap solution
to che'ck fusible plugs for leaks before removing tyre. Leaks c'an usually be
pinpointed to the plug itself (a poor bond behbeen the fusible material and the
plug Body, or to the sealing gasket used. Be sure the gasket is one specified by t h e
manufacturer and that it is clean and free of cuts and distortion.
If excessive heat has caused a fusible plug to blow, the tyre may be damaged and
should be replaced. After a fuse plug in a wheel blows, the wheel must be
inspected to ensure there is no mechanical damage (using NDT equipment a s
appropriate) in accordance with the manufacturers instructions. This will include
bearings and all wheels on the bogie.
The inboard wheel half may contain a pressure release plug, a safety device that
prevents accidental over inflation of the tyre. If the tyre is over inflated the
pressure release plug will rupture and release the tyre pressure. A soap solution
can be used to check a release plug to determine whether or not it is defective.
Wheel Base
Air escaping through a cracked or porous wheel base is best found using an
immersion test.
Bead Stick
Tyre levers may be used to break tyre bead stick on wheels equipped with a tyre
and tube combination only when no tyre removal machine is available or when
the design/size of the wheel and tyre make the use of the machine impossible.
Tyre levers MUST NOT be used on wheels designed for tubeless tyres if the sealing
between the wheel and the tyre are to remain unimpaired. Tubeless tyres must
only be freed from the wheel bead seats using a tyre removal machine.
Flanges, Brake Drums and Drive Blocks
There is a need to consult the relevant bay servicing procedure for comprehensive
details relative to a particular type of wheel. In general the procedure is a s follows:
1. Clean all metal parts with trichloroethane and dry with compressed
air. Ensure bead seat areas are free from grease, oil and foreign
matters, eg rubber smears. Clean roller bearing component with
white spirit, thinners or trichloroethane. Bearings corrode rapidly if
left un-greased. Ensure cleaning, examination and re-greasing
completed within 30 minutes. Alternatively, coat bearing with light
oil, eg DTD585 temporarily until required for assembly, then clean
and re-grease.
2. Examine wheel flanges for chips, dents and flats. Such damage may
be dressed out with a smooth file and emery cloth, blending out any
sharp edges. Dressing must be kept within permitted limits for
- ----1:-.l-1- I--&---
-I------ 4.-
~lcgllglulcucullasc ( I C L C I - - L U -
4.L- --I
LIIC L CLCVCULL
+ ---L--l
WLACCI
----L1:--+:--i
pu U L I L a L l u L I j . TL:-
L LLLD
Wheels designed for disc brakes have only drive blocks fitted and no
other brake components fitted - usually.
3. Check the drive blocks for wear, security, damage and corrosion.
After any repair or inspection of a wheel or its parts, particular care must be
taken to restore any protective finish.
Tapered roller bearings fitted to aircraft wheels require careful adjustment when
the wheel is fitted to the aircraft axle. The predetermined clearance 'End-Float'
ensures the bearing is free running and the bearing takes u p its normal path. It
also allows for expansion because of heat generated by the brakes.
- 32 -
rnoodull l A-1283
GENERAL
The following precautions are advisable in handling both tube-type and tubeless
tyres, especidly those with high inflation pressures.
1. Inspect fusible plugs. Fusible plugs are used on the tubeless wheels
of high performance aircraft to relieve excessive pressure created by
excessive brake heat. Fusible plugs are generally not removed during
a routine tyre change unless they are defective or the wheel is
subjected to degreasing and cleaning. They are, however, always
removed a n d inspected during wheel assembly and overhaul.
,
wheel). '
I --
', ", I
-
--
-//
_,
3.
f r o q wheel flanges.in^ i
Take special care wien encoudtefing difficulty in frkeing tyre beads
to p b beads free incorrectly may cause an
' accident. Even with special tyrk i;krnoval tools, care imust be taken to
damage t o beads-or-whekl flanges. On s.all_&res, successive
---pressing with a two-foot length of wood close to1the-bead or tapping
with a rubber mallet is generally sufficient. On large tyres, a
hydraulic or mechanical bead-breaking press may be required. If
using a 'bead-breaking' press, some method should be used to
prevent further movement of the tyre bead after it is broken away
from the bead seat area.
WHEEL CHANGE
Always consult the AMM, but the following points should be noted:
---La
-
T - n mr\ A rrr-T3
JsbrmJsa 1 u i-uJsLmr 1 vv n n f i ~ a
1
A - TT7T T P P T
-
corrosion Removal
The procedure to be used when removing corrosion from a particular wheel would
be laid down in the relevant servicing manual. The following is an example of a
typical procedure. Slight damage or corrosion may be removed by polishing out
with a smooth hone or grade 00 carborundum cloth. Restore the protective finish.
This can be affected by careful use of a smooth file, hone or carborundum cloth.
Lightly polish away the damage taking care to stay strictly within the limits laid
down in the particular manual.
Replacement of bearings and seals must be canied out strictly in accordance with
the Wheel Manual. Details of the pressing and removal tools for a particular
wheel are given. A typical example procedure for pressing in an outer race is as
follows:
1. Grease the bearing housing in the liner, steel sleeve or hub with the
approved lubricant.
2. Set u p the wheel on the hydraulic press table with press tools in
position.
3. Position the distance piece over the mandrel, then place the h u b over
t h e mandrel.
4. Position the outer rat-e on-the lip of the bearinghouskg with the
- -
I
smaller diameter of-thesleeve'in the outer race! ~ocate~,he\collarover
the mandrel. I I
'!
I \'
1 1 1
I
5. Ensure the head of (he mandrel is central beneath the jack. Apply the
I
minimum of hydraulic pressure
- necessary to push the outer race in
its housing. -- - ,
,, - - /
I
I I
I I FIXED STRU,CTURE
OF HYDRAULIC,
--
- -
OUTER RACE
EXTRACTOR
B O T O M OF HYDRAULIC PRESS \
END CAP
- 35 -
moodull l A-1286
WARNING
It is important that no excessive pressure is applied to the outer race during this
operation. Investigate the cause if the outer race will not seat correctly. Failure to
adhere to this instruction could result in irreparable damage to the wheel
structure.
Remove the press tools and check with a 0.0015in feeler gauge that there is no
gap between the base of the outer race and its seating in the bearing housing. If
the gauge fits into a gap, set u p the wheel press and tools as before and apply
further pressure.
The inner race would normally be placed in position after being lubricated and
retained, with the seal in its housing by a circlip.
Replacing-Fusible Plugs
I
:1. Smear the new seals and new '0' rings with the type of silicone grease
laid down in the servicing manual, eg silicone grease. Insert the seals
into the fusible plug casings and fit the '0' rings around the casings.
I
I
2.' Grease the threads ofitheplugs with the same grease type used on
the seals and screw them into the wheel well to a torque loading of 16
- lb in (or as laid down). Secure plugs with locking wire to adjacent lock
- - -
screws.
NOTE. The '0' ring seal of a tubeless wheel should be carefully cleaned and
inspected for defects before being lubricated and installed. If its condition is a t all
questionable, it should be replaced.
It is often desirable to lubricate the toes of inner edges of the beads. This is done
with an approved talcum powder only. This will facilitate mounting and seating of
the tyre beads against the wheel flanges. Care must be used with tubeless tyres,
however, to ensure that none of the talc gets on the sealing area of the bead.
rnoodull l A-1287
WHEEL/TYRE ASSEMBLY BALANCING
Balance marks are placed on many tubes to indicate the heavy spot of the tube.
These marks are often paint stripes about ?4 inch (12mrn)wide by 2 inches
(50mm) long. When a tube is installed this balance mark must be aligned with
the light spot' balance mark of the tyre (red dot).
With some split wheels, the light1 spot of thb wheel halves i s iddicated with a n 2'
starnpgd on the flange. In assembling the& &heels, position thk 'L's 180/degrees
apart. If additional dynamic or static b d ~ ~ i is' n
required
~ after,tyre mounting,
many +heels have provisions for attachiqgaccessory balance /w&ight$afbund the
circumference of the flanges. 1
I
\,,
\ I
I - -,'
\ I
1 wheels balanced
~ n b d a n d e dwheelk can also proddce v i b r a t h . Be sure to have
according to in/structions specified :by the aircraft or wheel manufacturer. They
will nom'ally be statically and dynamicalw balanced, ie balanced in two planes.
I - - - A'
-- I
AIRCRAFT BRAKES
Brakes are designed to convert the kinetic energy of the moving aircraft into heat
energy by friction. They must produce enough friction and have enough heat
capacity for the weight of the aircraft and must also be able to dissipate the heat
generated.
They are not allowed much time to perform this task. In the case of a n RTO when
the aircraft weight and speed is high and conditions are much more severe the
brakes are tested to their upper limit. This can be shown in the fonn of a
Power/Time Curve where the kinetic energy absorption rate is depicted.
200
.
-.:--*----
I
------- *
*
45 SECS 30 MlNS
TIME
'LANDING
-5,
COOLING
In the early days drum brakes were used, operated by air supplied by a
compressor, or the aircraft engine. These brakes suffered from brake fade and
distortiondue to heat and were-soon replaced by the copper disc brake.
L. - .- - --
Friction
The amount of friction developed in a brake will vary depending on many factors
but in general the amount of friction generated is given by the equation:
- 38 -
rnoodull l A-1289
It can be seem therefore, that in general the greater the force (RN) the greater the
friction. One of the reasons why discs are better than drums is that the drum
distorts with the high radial forces created by the brake pads or shoes. This
means that with a disc brake greater RN can be applied without fear of distortion
of the discs. Also with modern heat packs the total surface friction area is greater
than with a comparable sized drum brake.
DRUM BRAKES
Although used extensively on earlier aircraft, drum brakes have largely been
superseded by hydraulically operated disc brakes on most modern high
performance aircraft. Pneumatically operated drum brakes may still be found in
service, however, and the construction, operation and maintenance of a typical
brake unit is described in the following paragraphs.
I
- -- --- --- -
RNETS SECIJR~G
TUBE \*<
EXPANDING BRACKETTO BRAKE LINING
BRAKE LINING i
, /BRACKET i
t BACK PLATE
I
NUT AND BOLTS , SPRING
SECURING
a SPRING CLIP
BRAKE UNIT
TO AXLE 61-&1
AXLE FLANGE
ROTATING BRAKE
This unit is cylindrical in shape and is attached to a flange on the axle. It houses
the expander tube, brake linings and pneumatic connections.
Expander Tube
This is a circular, reinforced rubber tube of flat cross-section and is fitted around
the back plate. It has a pneumatic connection leading through the back plate to
the aircraft pneumatic system.
Brake Linings
separ+tors
Phosphor-bronze gauze separators are fitted between the ends of the brake lining
segments to reduce heat penetration to the expander tube and to exclude carbon
particles.
Brake Drum
The brake drum is a heavy steel cylinder, attached to and rotating with the wheel
and against which the brake lining segments expand to produce the braking
action. I t may be of bimetallic construction to rninimise heat distortion.
Normally fitted so there is an air gap between it and the wheel around its
circumference - to allow for better cooling and help prevent heat transfer to the
wheel and tyre (heat sink into the tyre will cause a pressure rise but more
importantly can cause deterioration of the tyre structure and possible tyre failure.
When the pilot's control is operated, air pressure is applied to the inside of the
expander tube which expands and forces the brake linings out against the brake
drum. When air pressure is released the expander tube collapses and the brake
linings are withdrawn inwards from the brake drum by the action of the return
springs.
Removal/ Installation
When the wheel has been removed, the brake unit can be removed by
disconnecting and blanking the air pressure connection and removing the bolts
attaching the back plate to the axle flange.
When installing a new brake drum, the protective treatment applied for storage
purposes should first be removed with a suitable solvent such as methylated
spirits. Petrol or paraffin should not be used.
,.
i/
-- - --...--
-
i----., ,,
i j
i ' ,.- /
lnspectio+
I j ?'!,
! c I i
I
Drum qrakes a r e not norrnally aycessible fyk gisual inspectiori d h e n installed on
the aircrdLDdring a preflight inseectionthk back plate and wheel should be
examihed for signs of overheatlngand-theflI'exible pneumatiE h o d between the
brake units and the landing gear leg should be checked for damage, security or
leaks. Operation of the brakes may be checked by means of the brake pressure
gauge and also by checking that air is discharged from the brake relay valve when
the brakes are released.
Brake segments should be exarnined for wear by measuring the thickness of the
remaining material, the minimum thickness permitted for replacing the linings
being laid down in the AMM. Any carbon deposits should be removed with a stiff
bristle brush.
- 41 -
moodull l A-1292
Test After Reassembly
DISC BRAKES
Most modem aircraft are fitted with hydraulically-operated disc brakes (also
known as plate brakes). Light aircraft generally have a single-disc type and larger
aircraft, a multi-disc type (also known as segmented plate brakes, heat packs etc).
--- - -
- . -
SEGMENTED
HYDRAULIC DISCS (ROTORS)
1000 HP KE 1% ft Ib
COPPER DISCS
DRAG 2 TONS ROTORS (FOUR)
BRAKE PADS
2 5 HP KE 50M ft Ib
DRAG 4 . 8 TONS
-- -
i---- -- -
,- Fig. 18 CONCORDE~'~AKE UNIT (CARBON) - , \
I ' , \
\
'
'\
1
1 1
i'
I 1 II 'I
NIT (COPPERDISC)
I
D U N L ~ PHYDRAULIC BRAKE i /
1 1 1 _ /' _, I ;
An old;unit and included here o,nly&givt(& historical background-io the
developnient of the disc brake unit. ~ a & ~ o f \ c o ~
to~allow
er &en heat
distribbtion and hence
, less ch&ce of dist&!ion.
I
I
I I
I
I 'I I I
1 i
The cob$er dis,e'k b e r e driven bd t$e wheey amd chromium plz@d to provide a hard
:__.. -- .d C ___ .
1
wesu;idg kuda<e./ (The discs were bapagable o 'being re-plated)..' !,--
_-, j
The torque plate was bolted directly to the axlal/landing gear unit and hydraulic
pistons would clamp the whole assembly, during the braking operation, to provide
the retarding friction.
This type of unit required regular adjustment to allow for wear as no wear
compensators were fitted.
The maximum permissible wear of the friction pads fitted to this unit is indicated
by a dimension taken from the face of the torque plate to the friction face of the
first brake plate, with the piston rods screwed fully home. When the limiting
dimension is reached, all the friction pads must be renewed.
No direct measurements are involved when checking the copper brake plate.
Scoring of the plates is permitted until the plating a t the base of the scores is
broken. If any lifting of the plating is evident, the plate is classified as
unserviceable and the inner and outer plates must be changed as a matched pair.
Tenon minimum permissible width is measured with a wear gauge special tool.
rnoodull l A-1294
SINGLE-DISC BRAKE UNITS
A simple single-disc brake unit is shown and is of a type found on many light
aircraft. A single operating cylinder is shown but two or three are often used for
increased braking performance and larger aircraft may have brakes using five or
six cylinders. The brake unit consists basically of a light alloy torque plate
shaped for attachment to the landing gear leg or axle flange, housing a calliper-
type hydraulic jack unit and a pair of friction pads. A solid steel disc is slotted
into the wheel and rotates between the friction pads.
When the brakes are operated, fluid pressure is applied to the cylinder and forces
the operating piston towards the disc, thus squeezing the disc between the
operating and fixed friction pads and thus resisting wheel rotation. When the
brakes are released the disc is free to rotate between the friction pads.
m ..,m-
nT
.,s
UWULIL
m. .- SEALING PISTON
-\ - fin-.-.
---
.L -.-..,A -.--.--I,
u r c w I IIUU 1-13 I UIU
-
-
-
--
The brake unit should be examined periodically for fluid leaks, damage or
corrosion, the friction pads for wear and the discs for scoring or pick-up of surface
plating. The single discs used on light aircraft brakes are prone to corrosion and
pitting and this may lead to rapid wear of the friction pads. Discs in poor
condition should be replaced or machined to give a clean surface a s appropriate.
Discs worn below their minimum width dimensions should be replaced.
Replacement of worn pads is normally a simple procedure once the wheel h a s
been removed and often does not necessitate breaking down the hydraulic system.
rnoodull lA-1295
THE MULTI DISC BRAKE UNIT
The friction pads may be made from sintered metal or more conventional pad
material.
A typical multi-disc brake unit is shown. In this unit a torque plate and torque
tube assembly fits over the axle and is bolted to a flange on the axle; alternative
designs are often similarly mounted but prevented from rotating by means of a
torque arm attached to a suitable furture on the landing gear leg or bogie. A
number of cylinders are spaced around the torque plate, connected to the
hydraulic brake system and house pistons which apply force to the pressure
plate. _
-
_ -- --
\
-
-',
-
! 1- 7 r---, \
-- \
The dlsc pack contains alternate stationary and rotating discs the-Gtationaq
discs being keyed to the torque ;tube and !he rotating discs dei'Ag keykd fo drive
blocks in the wheel hub. In this1 ubit the stationary discs house the brake pads
-_-
and tHe rotating discs are segmented to p5e&ent head distortko: and brake drag.
~ o r r e dworking
t clearance in thk disc packjs maintained by 'means-df adjuster
assemblies. Pins attached to the p r e s s h e plate and protruding-through the
torqud plate on t q s brake unit, indicate the kmount of wear which has taken
place in the disy'pack. II I I
I
i ' I '
I I / I I ,' /
A h p h e r -typ6of'multi-disc br&e 'is-kno&nis a tri-metalli~~br*. ~i Construction
/'
is similarto-the-brake unit described-except that the rotatihg-discs have a metallic
compound sintered to their faces and steel segments, known as wear pads, are
riveted to the faces of the stationary discs. Alternatively, the faces of both sets of
discs may be sintered, or the stationary discs may be plain.
When the brakes are applied, hydraulic pressure is admitted to the cylinders and
moves the operating pistons against the pressure plate. The friction loads
generated between the stationary rotating members provide the required braking
action. When the brakes are released, springs in the adjuster assemblies move the
pressure plate back to maintain a working clearance in the disc pack and permit
free rotation of the wheel.
Maintenance
ROTOR DRIVE
BLEED SCREW PRESSURE BLOCKS
AUTOMATIC WEAR
ADJUSTER
\ / STATORS
/
In some installations a worn disc pack may be exchanged after removing the
wheel and thrust or back plate and without disconnecting the hydraulic
connections, but in order to carry out a detailed inspection the brake unit must
be removed from the axle.
At the periods specified in the maintenance schedule the brake unit should be
removed for inspection and overhaul. The wheel should first be removed and the
hydraulic pipe couplings should be disconnected and fitted with suitable blanks.
rnoodulll A-1297
In some cases fluid will drain from these pipes and bleeding will be necessary
after re-connection, but in other cases connection is by self-sealing couplings,
which isolate the hydraulic system from the brake unit. The brake unit
attachment bolts (and, where fitted, the torque link) should then be removed and
the unit withdrawn.
Following its removal, the brake unit should be dismantled, cleaned and
inspected. All metallic components should be thoroughly cleaned and dried; if
chemical solvents are used they must not be allowed to come into contact with the
seals. Inspection will include:
---
beybnd limits
or
I I
/
,
i
I
i j 1
The ,torque plate, , t d r & e u b C ~ dthrust plate-shobid be examined
forcracks, corrosion5-distorti6n and damage, p&-iedlar attention
being paid to bolt holes and other highly stressed areas. Cylinders
and pistons should be inspected for scores or other damage and
springs inspected for corrosion and given a load/ compression test a s
specified by the manufacturer.
Protection treatment should be applied to the metal components and the unit
reassembled and tested for leaks and correct operation. It is normally specified
that new seals, gaskets and self-locking nuts should be used for reassembly and
all fasteners torque loaded in accordance with the manufacturer's manual. The
unit should be primed with hydraulic fluid and blanks fitted.
When re-installing the brake unit on the axle, care must be taken not to spill fluid
on the disc pack. Jointing, sealing or anti-seize compounds should be used where
specified and all fasteners and pipe connections should be torque loaded and
locked to the manufacturers requirements.
Adjuster Assemblies
SPRING HOUSING
FRICTION BUSH
\ W1
!?ETP"A..CT!n!'!
PIN
PLATE
When the brakes are released the adjusted spring pulls the guide back until it
contacts the spring housing, the clearance between the guide and torque plate
being the designed running clearance. A s wear takes place i n the disc, the
pressure plate has to move further forward, thus pulling the retraction pin
through the friction bush by an amount equal to the disc wear, but maintaining
the design clearance when brakes are released. On some brake units wear may be
assessed by measuring the protrusion of the retraction pin.
On initial assembly a special tool is used to position the retraction pin a t the
position of maximum protrusion through the friction bush. The pin takes u p its
initial operating position when the brakes are first applied.
These are similar to the conventional multi-disc brake unit except the rotors and
stators are made of carbon and are of single piece construction. They are lighter,
run a t higher temperatures and are more efficient.
The method of bleeding the brakes will depend on the particular aircraft system
and reference should be made to the AMM. However, the normal method of
bleeding is to pressurise the brake system, open the bleed screws fitted to the
brake units and apply the brakes from the flightdeck. Allow hydraulic fluid to flow
through until air free fluid is discharged; the bleed screws are then closed and
brake operation tested. Bleed fluid should be piped to a suitable container and
(' - must not be allowed to come into contact with the disc pack and must not be re-
\ 1 7
\,
7 -
"\ -\ - -,
On lo&-bressure brake systems, a s fitted'to h a n y small aircr*, thgpressure is
generated by the pilot pushing fhe appropeate brake pedal d o h .
I
1
On high'pressure brake system? (asfit$ed t6 most large airc!afk), the (associated
hydraulic accumulator is pressured-and as /' the brake pedal is depresyed, fluid is
,
' \
forcedi out of the bleed screws uhder pressune. In this type ob systemHitis
\
sometim~esrecommended that only a specified quantity of fluid1is discharged and
it may be necessary to bleed ot$e$ parts ofithe system such bsj where fitted, the
servo system frbrh the brake pedqs to thelsl#ve units (four small systems each
with-its 0-3-eservoir) and the normal and,emergency a c c y ~ u l a t o r s before ,
bleebing-the-brakes. After bleeding the-appropriate r e ~ e r v o i ~ s h o i l be
l d topped u p
a s necessary.
Brakes are normally tested after overhaul and after installation on a n aircraft,
while the aircraft is still jacked up. The wheel is spun u p by hand and the brakes
applied several times and released; there should be no leakage and the brakes
should stop the wheel when applied and allow wheel rotation when released.
On some aircraft, in order to inform the pilot of excessive build-up of heat in the
wheel brakes, a brake temperature monitoring system is fitted. A typical system
includes a temperature sensor at each wheel, which supplies information to a
central monitor and warning devices on the flight deck. The monitor contains a
temperature gauge and a selection button for each wheel. The gauge normally
records the temperature a t the hottest brake and a button illuminates when the
associated brake temperature exceeds a predetermined amount. When any button
is pressed, the gauge records the temperature at the associated brake.
On aircraft with CRT display systems brake temperatures (and tyre pressures) are
displayed in colour on the screen.
For testing purposes, operation of a BIT test switch will cause system decals to
illuminate and gauge readings to move to the test signal range when all circuits
are serviceable. - -
\
- -
Routine maintenance includes inspection'of the sensors and asSociated wiring for
security and damage and functional tests of the system using the appropriate test
switches and BIT systems.
With the 'Glass Cockpit7type of aircraft su6h as the Boeing 747-400,-B777 and
the Airbus aircraft, flight deck indications are via CRTs. , - -
The CRTi~anding
~ e a page
r will show details such as:
I
~r Brake temperatures
* Tyre pressures --
(See the books in this series entitled Hydraulics; Landing Gear and
Instrumentation.)
SKID CONTROL
The braking systems of most modern aircraft are provided with a means of
preventing the wheels from skidding on wet or icy surfaces and of ensuring that
optimum brakmg effect can be obtained under all conditions, by controlling the
hydraulic pressure to the brakes automatically. Anti-skid units/ transducers
sense the rate of change of wheel deceleration, decreasing the hydraulic pressure
applied to the brakes when a high rate of increase in deceleration occurs (ie
consistent with an impending skid) and restoring the pressure to the brake a s the
wheel accelerates again.
- 50 -
rnoodull lA-1301
A modulator is often fitted in conjunction with the anti-skid unit, to restrict the
flow of fluid to the brakes after initial brake application and to conserve main
system pressure. There are basically two types of anti-skid systems in use, the
mechanically controlled system and the electronically controlled system.
The mechanically controlled system (rare) can use either a wheel mounted unit or
a n axial mounted unit
The anti-skid control valve (automatic) is positioned in the hydraulic brake line
between the brake control valve (controlled by the pilot) and the wheel brake unit.
When autobrake is selected, it also supplies fluid to the brakes via the anti-skid
valve.
,' I1
I
I
I
I
I
I
I
' I
I
I
I
1 I I
I )
This unit is mounted either on the wheel brake unit or on the landing gear
assembly so that the rubber tyre rests on and is rotated by the rim of the aircraft
wheel.
The unit consists of two main parts: a hydraulic control valve (operated by the
flywheel); and the flywheel assembly. The flywheel is housed inside the rubber
tyred shell which is rotated by direct contact with the wheel rim.
moodull l A-1302
The control valve has four connections:
* Pressure supply - from the pilot's brake control valve.
* Return - to the hydraulic reservoir.
* Brakes 1.
* Brakes 2.
NOTE. With-this-typeof unit the spring acts as a sort of memory- when the wheel
decelerates too quickly, as determined by the spring, then the valve is caused to
operate and reduce fluid pressure to the brake.
As shown in the exploded view the drive from the rubber tyred shell is transmitted
to the flywheel via a drive ring, drive spring and drum. The drive pegs of the shell
engage with the slots on the drive ring to drive the drum through the spring. One
end of the spring is connected to the drive ring while the other is connected to the
flywheel. The spring is coiled in such a way that a s the unit is being driven the
spring expands and drives the drum (and flywheel) by a positive friction drive.
The flywheel, mounted on the outside of the drum, is driven through its spoke by
two segmented bosses attached to the drum. A lightly loaded main spring links
the flywheel to the drum and tries to keep the flywheel spoke in contact with the
driving faces of the segmented bosses.
rnoodull l A-1303
Two thrust balls are located in the flywheel spoke and are kept in contact with a
cam on the drum by a thrust plate attached to the end of a spring-loaded thrust
rod.
The thrust rod is connected via a system of levers to the hydraulic control valve.
With the brakes applied and when the landing wheel starts to slow down too
quickly - that is, starting to skid - the rubber tyred shell slows down a t the same
rate, a s does the drum (because of the friction drive of the spring). But the
flywheel, with its momentum does not slow down and starts to overrun its
position against the load of the main spring. This will cause the flywheel spoke to
make contact with the faces of the two-segmented bosses, which will drive the
drum against the frictional resistance of the drive spring.
. ~ .
/--
PRESSURE
SU,PPLY
I
i
!
I
I
I
4NORMAL BRAKING CONDITION
'
1 ,
'
- .- ; , L - - ',
; WHEELRIM
r-- ,,' ' L-.
Movement of the thrust rod will shut off brake pressure supply and open the line
from the brakes to return.
After the unit operates the flywheel is slowed down by the drag of the drive spring
and with the brakes off, the landing wheel regains speed. This will cause the drum
to begin to drive the flywheel again and the thrust balls and thrust rod will regain
their positions (with the aid of the return spring), and normal brake pressure will
be re-established.
Should the wheel bounce clear of the ground during landing the wheel will stop
instantly. This will cause the anti-skid valve to release the brake pressure
completely and re-apply it some 4 seconds later, which should be enough time to
allow the wheel to make contact with the ground again. -
Installation
The mounting details of the various types of mechanical units vary considerably
and reference should be made to the AMM:for details of any particular
installation. The whole unit is spring-loaded, or the mountings shimm'ed, to
maintain satisfactory driving contact with the aircraft wheel rim. The tyre loading
is normally checked after installation by measuring the flat produced on the
rubber tyre at its point of contact with the aircraft wheel. i
The unit contains components similar to those found in the rim driven type.
Additionally the unit also includes a sun and planet gear assembly - to increase
its speed ratio with the wheel and a clutch to absorb sudden start u p loads.
If the landing wheel decelerates too quickly (an impending skid) then the flywheel
will run-on relative to the input and main shafts. This relative movement between
the main shaft and the drive ring will cause the two thrust bearings to ride u p the
cam profile and move the thrust rod against its spring to open the control valve
and release the brake pressure.
moodull l A-1305
MAIN SHAFT DRIVE RING CLUTCH FRICTION
MAINSPRING VALVE \
THRUST ROD CLUTCH SPRING
->
- -
RETU
\
The thrust rod opens The 30 deg movement of the drive
4 the valve and relieves the
@ ANTI SKID CONDITION pressure in the brakes @ ring forces the thrust bearings to
ride up the cam face
moodull l A-1306
Bleeding
Bleeding of the anti-skid unit is normally achieved when bleeding the main brake
system but independent bleeding may be necessary after installation. This is
carried out by fitting a drainpipe a t the exhaust connection, rotating the drive
smartly in the direction of rotation, then bringing it to rest.
Each time rotation is stopped, fluid will be discharged from the exhaust port and
bleeding should be continued until the discharged fluid is free from air, then the
pipe connections remade.
A t the periods specified in the maintenance schedule the unit should be inspected
as follows:
--
\
;;;( ~ r r c ---:+
TL- .ULUL .-.L---lA
OALVUIU ~b
\ l a o + - , ~ -Am i l ; ~ P ~ P P + fni-
'ha~UAU-I~U -IU IAAV~UUCUU
P A
r v z
P P P I I Y ~ ~ J
u-urn--- J 2
~ i o r n c~f
--?---
corrosion, external damage and leaks (with brakeg applied)
(b) The pipelines should be checked for damage, distortion and the
connections for security of attachment, and leaks.
- - - -
(c) The driving tyre and wheel should be inspected for correct loading
and alignment and the tyre for excessive wear. ,
1
NOTE. It is possible to lock the spring-loaded type units out of contact with the
wheel track by inserting a pin in the mounting stud. This is done to allow
wheel removal, and it is recommended that a red streamer-should be attached
to the pin a s a visual reminder that the anti-skid unit is out of operation.
With the brake on the indicator rod should be approxim.ately flush with the
surface of the unit.
The system comprises a wheel speed transducer, a control unit (computer) and an
anti-skid valve in the brake pressure line, together with associated switching, BIT
and check-out and warning lamps. The wheel speed unit may supply either dc or
ac depending on the type of system used. Operation is basically similar to the
mechanical system but the use of logic circuits in computers enables much finer
control to be exercised.
moodull lA-1307
Further refinements such as strut oscillation damping circuits, touch-down
protection and locked wheel protection and auto brake may also be incorporated
and some systems automatically de-activate a t low speed to prevent interference
with normal taxing manoeuvres.
If this fails to prevent the wheel from skidding then a further signal will cause all
remaining brake fluid pressure to return to the reservoir. Only when the wheel
regains its speed will the pressure be allowed to the brake. (All this takes place in
a fraction of a second.)
JF
I
~ e n e r b t &System
r
1'
I
mounf ed 1 I
/ I I
AXLE SPRING
- 57 -
rnoodull l A-1308
When the wheel slows down the voltage drops. This information is used by a
control unit. If the rate of slowing down is too great (voltage drop too quick) then
the control unit will send a (dc) signal to a solenoid on the anti-skid valve. When
energised this will release the brake pressure.
With the brakes off the wheel will regain its speed, the generator voltage will be re-
established, the control unit solenoid will be de-energised and the brakes will be
re-applied.
This consists of a tacho probe (a magnet around which is wound a coil) which is
caused to produce a pulsed dc (a sort of ac) output by being close to a ferro
magnetic exciter ring. The frequency of the output of the probe is dependent on
the speed of the exciter ring (attached to the aircraft wheel). This signal is sent to
a comparator/computer for processing. -- .-
BRAKE UNIT
EXCIT'ER RING
The probe may be housed in the axle or fitted as shown in figure 28.
As the wheel starts to slow down so the frequency output of the probe drops. This
rate is compared by the control unit/computer with either a known maximum
frequency reduction, or the actual rate of aircraft deceleration (from the Inertial
Reference System).
If the deceleration rate is high enough then a signal will be sent to the anti-skid
valve solenoid to reduce/stop the pressure to the brakes.
If the wheel retardation rate is being compared to the aircraff retardation rate
then the wheel can be slowed a t a rate which is a percentage of the aircraft
slowing rate - t h u s maintaining maximum braking efficiency.
This system is more sensitive than the others and therefore the brakes can be
kept a t just the right level of braking for maximum efficiency.
I HYDRAULIC
PRESSURE
BRAKE CONTROL
VALVE
I
I '
I
VALVE
\
I , WHEELSPEED AND , , / I
I '
ACCELERATION I --- '/'
I
I
I
COMPUTER 1 - -. . ' \ \
1 - -
I /
' \
'
,
4
I
\, I PRESSURETO
TACHO,;SIGNAL OF WHEEL I BRAKES
I
SPEED AND DECELEFXTlON 1 1
/
m
2
COMPUTER ,-, - -
\ - ,
- 1
'
' I
WHEEL AND BRAKE ASSEMBLY
L -
Control units/ computers normally contain circuits which provide warning failure
in the system and a self-test facility which enables the serviceability of the various
components to be checked. Controls for the operation and testing of the anti-skid
system are contained in the control unit/computer and on the flight deck.
Maintenance
The inspection, testing and maintenance of any particular anti-skid system will
vary considerably between different installations and details should be obtained
from the AMM.
- 59 -
rnoodull l A-1310
However, the self-test facility normally enables complete testing of the system to
be carried out and the test circuit is designed to facilitate location of faulty
components. A visual inspection of the system should include the following:
The following is a general description of the A320 and B767 anti-skid systems.
There should be no need to remember the details of each system but the
principles should reinforce those already learnt.
The anti-shd system is based on the optimisation of the aircraft deceleration rate
a s measured by the ADIRS (Air Data Inertial Reference units): Maximum braking
is provided by maintaining the wheels a t the limit of an impending skid.
,
- - I I -
1 r-
, HYDSUPPLY
I
AMPLIFIER
The speed of each main gear wheel (given by a tachometer) is compared with the
aircraft speed (reference speed). When the speed of a wheel decreases below 0.87
times reference speed, brake release orders are given to maintain the wheel slip at
that value.
Anti-skid Overview
The rate of wheel retardation is compared with the aircraft retardation rate
(picked off from the IRS) and should the wheel start to slow too much
(approaching a skid) then a signal will be sent to the anti-skid valve to reduce the
pressure to prevent the wheel skidding. Once wheel speed has been regained then
the pressure signal is re-instated. This process is carried out in a few millseconds.
The anti-skid can be switched off from the flight deck. When off, a warning light is
ON in the flight deck.
The alternate system is similar to the main system and the supply is fed in via
shuttle valves. These are pressure operated.
- 61 -
moodull lA-1312
RIGHT HYDRAULIC
SYSTEM SUPPLY
CONTROL SIGNALS TO AUTOBRAKE PRESSURE
CONTROL VALVE
FEEDBACK SIGNALS
* CONTROLLED PRESSURE
R = RETURN FLUID
Autobrake Overview
The pilot can select (prior to landing) 1 of 5 brake settings with deceleration rates
from 4.5ft/sec2 to 1lft/sec2. This allows for "feet-ofl" automatic operation of the
brakes.
rnoodull lA-1313
-k
Have weight switches made for more the 0.2 sec.
-k
Have correct spoiler lever position.
~r
Have wheel spin-up circuited activated. Activates when all
wheels are 60kt or greater and deactivates when average
velocity drops below 30kt.
The autobrake supplies brake pressure to the brakes via the anti skid system
entering the system via shuttle valves and the systems are tested using BITE.
1. Transducer (8)
2. Anti-skid module, normal system (2)
3. Anti-skid module, alternate system (2)
4. ANTISKID fault light on flight deck (1)
5.
-6.-
-7.
. Anti-skid shuttle valve module (2)
ANTISKID ON/OFF s w i t h o n flight deck (1)
Anri-skid j a u i o b d k e corliroi dr+iiivi i 02 j i j
-_ .
-\
,' '
A N T I S ~ DON/OFF switch
I ' I
1 j
I
I
,1 I'
I
\
/ 1 I I I
I I
An ANTISKID O~('OFF switch provides 28,* dd power to the cbAtro1 unit when ON.
/ I
An -b&light d t h OFF legen&on-thes6itdh comes on tor- the pilots that
the anti-skid-system h a s been- turned-offkwith the ANTISKID s&itch in the OFF
position, the ANTISKID OFF advisory message appears on the EICAS display. The
ANTISKID OFF message will inhibit the ANTISKID/AUTOBRK maintenance
message unless ANTISKID/AUTOBRK has existed 10 seconds prior to the display
of ANTISKID OFF.
An amber ANTISKID fault light illuminates to signal anti-skid system fault when
any of the following faults exists. At the same time the ANTISKID advisory
message appears on the EICAS display.
The relays also control ANTISKID OFF light function and the ANTISKID OFF
advisory message on the EICAS display. When the four relays controlling paired
wheel fault indication are all de-energised (ANTISKID switch in OFF position), the
ANTISKID OFF light illuminates and the ANTISKID OFF advisory message appears
on the EICAS display.
A positive detent between the DISARM and OFF positions ensures that when
the switch moves to the DISARM position it does not overshoot to OFF and
prevent the AUTOBRAKES light from illuminating.
The AUTOBRAKES light is an amber light located near the selector switch. The
light, controlled by the selector switch, comes on when:
* The switch is a t DISARM position.
* The switch is a t OFF position and the autobrake module solenoid
valve output pressure switch shows presence of high pressure.
x The switch is a t 1, 2, 3 , 4 or MAX AUTO position and a system fault is
detected.
When the selector switch is at 1, 2, 3 , 4 or MAX AUTO, the light illuminates for
a moment as the switch is moved through the DISARM. The light then goes
out when the unit confirms that arming requirements are met. When the
system disarms, the light illuminates until the switch is placed to OFF or the
system is re-armed.
I
- r
-
The control unit compares each wheel speed with the IRS ground speed for
touchdown and hydroplane protection. A change in speed causes a change in
control signal to increase or decrease hydraulic pressure to tkie brakes.
- - ,
'
The unit, located in the main equipment centre, contains conFrol, BITE and
display circuit cards and a front control/display panel with alphanumeric
readout and BITE test switches.
The unit and-the circuit cards are LRUs. Data links in the unit provides means of
communication between cards. Power of 28v dc to the card supplies the 26v dc
and the regulated 5v dc source required for all logic circuits.
The main wheel card primary function is to control braking pressure and prevent
wheel skid or lockup. Each wheel card provides skid protection for two wheels in
tandem. Each wheel circuit shares a common power source line and is combined
by a locked wheel cross over function. A driver circuit in each card provides a
signal to the EICAS display via the EICAS computers when the anti-skid system
fails.
The autobrake card performs all autobrake functions, including control, logic,
interface and BITE. The card shares with the wheel cards for wheel speed and
system test information. A driver circuit in the card provides signals to the
AUTOBRAKES light and the EICAS computers when the autobrake system fails.
Both wheel cards and autobrake card contain self-test and status circuits. The
circuits check the system for fault and provide status to the BITE card.
- 66 -
moodull lA-1317
The BITE card communicates with all other cards via the data link in the control
unit. Its primary function is to monitor the operation of the four main wheel cards
and the autobrake card.
Two 4-valve anti-skid modules are used in the normal brake system. Each module
contains four identical anti-skid valves, four hydraulic fuses, a shut-off valve, two
inlet filters, a check valve and a restrictor. The module provides individual wheel
i\ control-to-each main gear. Each-module_<san LRU and therfuses,shutoff valve
anci iniet rilrers are separate c b m p o n e n r i k ~ s .Tne vaives 'anci fiiters can be
\
removbd for inspection without disconnecfilig hydraulic lines. \ 1'
I
I I
1
I _-
_-
. \
1 L---
Anti-skid Valve
Each valve in the normal or alternate module consists of two stages. The first
stage (servo valve assembly) develops hydraulic pressure proportional to the input
current. The second stage (slide and sleeve assembly) repeats this pressure at the
lower level required for brake control.
The first stage servo valve assembly consists of a torque motor a n d a hydraulic
circuit. The motor, an electromagnetic device, produces an armature deflection
proportional to input current, which positions the armature between two nozzles,
pressure and return.
The second stage slide and sleeve assembly consists primarily of a stop, a quill
and the slide and sleeve. Slide position is controlled by first stage output
pressure on one end and pilot's brake metered pressure on the other end.
The anti-skid valves in the normal hydraulic system operate in the unigain mode.
System pressure at 3000psi is supplied to the first stage providing a constant
pressure source by which the second stage is controlled. Through unigain
operation, the valve is able to maintain consistent stopping performance
throughout the brahng range, independent of applied brake pressure.
The anti-skid valves in the alternate hydraulic system operate in the multigain
mode. Pilot's brake metered pressure is supplied to the first stage rather than
system pressure. A s a result, the first stage output pressure is a function of both
metered pressure and valve current. Multigain valves are used in the alternate
system to simplify the system and reduce weight.
Hydraulic Fuses
The fuse prevents hydraulic fluid loss from the brake system if a line should
'
rupture a t any point downstream of the fuse. The fuse automatically_shuts off all
n ---- :r L L
llUW
- ;:^I-..--^^
11 LLlC
^C n.-:r3
V U I U I I I C ; Ul
---- :-,.. ,-.-
+Lwn L ;;+
uu&&l
11UlU p a r 3 o l l r f ; L ~ L L
;.-.
11.lo c v v 5 s ~ U L I
.I ~
;- PPlf-rocP++;nrT b
rl\IJ, I \IUV~-LV.YUII L IVUCCLLA
Fuse resetting is done manually by rotating the reset knob. This equalises the
pressure on both sides of the fuse and allows the fuse to reset. When the reset
knob is released, a spring forces the knob back to normal position. A slit in the
knob allows visual verification of the bypass valve position. i
Hydraulic Filters
- -
Two module filters, one a t the metered pressure inlet and the other a t the system
pressure inlet, to protect module components against debris ingress.
Shut-off Valve
A shut-off valve installed in the main module prevents system pressure from being
supplied to the anti-skid valve without pilot metered pressure input of 260psi or
more. When the metered pressure > 260psi, the valve ports fluid from the system
pressure line to the anti-skid valve. When the metered pressure < 240psi, the
valve switches and the flow is from the metered pressure line to the anti-skid
valve. The shut-off valve contains a check valve to allow metered pressure supply
to the first stage of the anti-skid valve if the shut-off valve closes.
rnoodulllA-1319
Check Valve
A module return line check valve provides free flow from the metered pressure
port to the anti-skid valve via the shut-off valve, and prevents residual pressure in
the brake return line from feeding back.
Restrictor
A 2-way restrictor is fitted in the system pressure line upstream of the shut-off
valve. The restrictor limits hydraulic flow during certain failure conditions.
The torque motor armature in the first stage of the anti-skid valve (servo valve
assembly) sits itself between twopnozzles , as a function of input current.
-. One
nozzie;is,sAppiied with sysrem-prepsure,dcj rhe other is connected~o\reiurn.
With rio command applied, the motor mobes',the annature agaihst thq 2eturn
nozzle a n d control pressure e q u h s supply pressure. With full current supplied,
the rnoto,rmoves the armature against the pfessure nozzle 4 d lcontrol pressure
equals rCturn pressure. For each ih-between value of input curkent there is a
/'
chara~teristicarmature positiod apddc&tro< pressure value. ~ k e - v a l ~,varies
e
pressure from a high of pilot metered pressure to a low of no pressure'(re1ease).
1
' I
I I '\ I, ' 1
The s2cohd stag; islide and sleeve assemblb) is a spool valve &ven by control
pressure 04
I I (frorn/{he first stage) one end df !he spool and b r a e pressure on the
other.~When-ontrol pressure e-xceeds-the'pilotysmetered pressQe, the spool
r'
movesto-port metered pressuhedireetly-to'the brake. In the metering region, the
second stage spool works as a pressure follower such that the brake pressure
equals the control pressure. The bias spring on one end of the spool holds the
spool down to allow full-applied pressure to the brakes when the first stage is de-
energised. A control orifice slows the second stage valve movement to control
input. At the brake port an outlet orifice slows the application rate of the brakes
in response to pressure input. When the metered pressure is removed, the return
check valve allows free flow return from the brakes.
The alternate module functions the same as the normal module except that the
pilot metered pressure is used. A characteristic of using metered pressure input
to drive the first stage anti-skid valve is a slight decrease in output pressure.
The module contains four identical valves. Each valve is independent and
pressure operated. Each valve shuttles pressure between normal and alternate
systems. The valve consists of a n LRU valve assembly and a n LRU filter. The valve
has a manual override plug feature.
In the event of shuttle valve failure, the slide plug on the face of the valve is
removed. A,flight dispatch plug (a fly-away ground maintenance tool consisting of
-a ~---I1
LLLCUL
+L=,J,A
LILLLUCCLU
-l-.m\
~ I
;c. ;-otollorl
L A ~ ,
in i t n n1-e-
rLu-yruvu.
IlluLculbu . i n c t ~ l l ~pr l ~ fnrC&
Tho
rrrurruAu-r
g the
in the valve to shift, thus blocking the normal port and opening the alternate port.
This condition remains with the plug installed. The plug has no [movingparts a n d
is equipped with a ring to allow an indicator tag to be tied to it whilst being used.
This is a speed sensing device fitted to each main gear wheel $.nd contains only
one moving part, a rotor which rotates inside a fxed stator. The stator attaches
to a support inside the main wheel axle. The rotor, using a four-arm dog rigidly
attached o n t h e rotor shaft couples to the transducer drive in-the hub cap. The
drive, consisting of a bellows-type coupling and related mounting hardware inside
the hub cap, turns the rotor when the wheel rotates.
The stator comprises a permanent magnet, a 150 tooth soft carbon steel pole
piece and a pickup coil. The magnet sets u p a magnetic field around the coil,
whereby the mating 150 toothed rotor produces dynamic discontinuities when
rotated. Turning of the rotor provides field changes as the mating teeth come in
and out of alignment to produce a series of voltage pulses (150 times per rev).
The voltage, related to the speed of the wheel, provides the control unit with wheel
speed data.
Autobrake Module
The autobrake module is connected to the normal brake lines and is located
within the wheel well. The module contains an Electro Hydraulic pressure control
Servo Valve (EHSV) (pressure control valve), an upstream three-way solenoid
shutoff valve and two pressure switches, located one each a t the outputs of the
solenoid valve and the servo valve.
The module is a n LRU as are the valves and switches. Solenoid valve, pressure
control valve and pressure switches can be replaced without removing the module
from the aircraft.
The module develops brake pressure in response to selected deceleration for all
required autobrake functions. The solenoid valve provides on-off control of
hydraulic power to the valve module and the pressure control valve controls
output pressure from the module as commanded by the control unit. Pressure
switches on the module monitor the pressure outputs from the solenoid valve and
the pressure control valve and provide the logic to the control unit.
The solenoid valve is a 2-stage, 3-way operated shut-off valve. When de-energised,
the valve moves to the right or closed position. The mechanical spring acting on
(- the spool-and the presence of ~upply_pre<sure(admitted via an intemal passage of
the spool)-provides the closing force. \
-\ r ---.. \
I --,
1 \
I I drives the piston to the
This force I ' ', kolates supply pressure from the rest
'right anp
\
A torque motor in the first-stage electrically controls jet pipe position and the
amount of flow to two receiver ports. One ports the pressure to return and the
other controls the pressure.
A feedback spring attached to the jet pipe on one end and the pressure-feedback
spool on the other counters the input of the torque motor. The spring returns the
jet pipe to its steady state position (for that particular pressure) when the
commanded pressure is reached. The feedback spool moves and compresses a
spring until the spring force equals the first-stage control pressure acting on the
area of the feedback spool.
Brake pressure and the first-stage command pressure act on equal areas a t
opposite ends of the second-stage spool which ports fluid either in or out of the
brakes as required until brake pressure equals the first-stage command pressure.
Without first-stage command pressure applied, a spring biases the second-stage
to return. A 0.070-inch diameter orifice in the valve return port limits brake
pressure release to ensure smooth brake release during autobrake disarm.
The pressure control valve pressure switch checks module output pressure.
When brake application conditions are met and the commanded deceleration
exceeds the actual aircraft deceleration by more than one foot per second squared
for more than three seconds, the system shuts down and the AUTOBRAKES light
comes on.
The assembly consists of a valve and a pressure-sensing syitch. The basic three- \
The valve h a s two input ports (one normal, one auto) and one'output port (brake).
Under normal operation, the normal port connects to the brake port. ' y h e n the
autobrake system applies pressure, a detented slide located i i the valve moves to
block the normal port. This slide shift allows fluid flow from the auto port to the
brake port.
The pressure switch, connected to the normal input port, checks pressure
downstream of the normal brake metering valves. When manual-braking effort
exceeds 750psi on either the left or right pedal, the switch opens to provide an
input to the control unit to disarm the system.
Circuit breakers provide 28v dc power through the ANTISKID ON/OFF switch to
the control unit. Four main wheel cards in the unit compare IRS speed data
inputs with wheel speed. This results in a control signal to the anti-skid valves,
which limit hydraulic pressure to the brakes. Two shuttle valve modules shuttle
pressure between normal and alternate systems.
The AUTOBK ANTISKID TEST IND 1 AND AUTOBK ANTISKID TEST IND 2 circuit
breakers provide 28v dc power to the interfaceldisplay card for BITE functions. A
data bus provides all the tie-ins between wheel cards, autobrake card, BITE card
and the interface/display card. The control unit provides fault signal to the
EICAS computers and the ANTISKID light.
- 72 -
The PSEU (Proximity Switch Electronics Unit) provides gear down signal to all
wheel cards for anti-skid system operation.
The microprocessor in each wheel card provides control for the fore and aft wheel
pair. The card receives and processes wheel speed signals, receives and decodes
IRS data, provides valve driver signals and communicates with the test and fault
inputs from the BITE card. A digital/analogue converter in the card provides the
i valv~commandto drive the re,spective-valve for each wheel, .
I 1 ,
Valv,eDriver Logic
L--
The wheel speed compares the applied brake pressure in three modes. These are
Proportional, Integral and Derivative. The Proportional mode involves applied
brake pressure with proportional wheel speed as the brake pressure changes to
maintain a deceleration rate short of a skid. The Integral mode checks the past
performance of wheel speed. The Derivative mode checks rate of change of the
wheel speed. The three modes provide the data input required to produce a
driving signal to the normal and alternate valve drivers. An alternate brake
selector valve determines which valve driver is used.
The signal goes to the respective anti-shd valve when the speed of the controlled
wheel is as least 50kt below the IRS ground speed. The hydroplane /touchdown
protection requires valid IRS inputs and that landing gear is down and locked.
Loss of IRS signal, however, does not affect other anti-skid functions.
Hydroplane/ touchdown protection for the forward wheel is provided indirectly
through locked wheel protection.
The gear 11psignal (when the left and right landing gears are not do-F and
locked) inhibits the alternate valve drivers for about 12 seconds., This is to allow
the alternate system brake pressure (left system pressure) to stop the wheels
before gear is retracted.
A low speed dropout a t 7kt inhibits the valve drivers in the wheel control circuit.
Below the dropout speed, the anti-skid system provides no b r k e release signal.
Brake pressure input of 260psi or more to the normal anti-skid module opens the
shut-off valve to allow system pressure supply to the anti-skid valves. On
alternate system, pilot metered pressure is supplied to the valve. The valve varies
the output pressure to the brakes by moving the slide valve between apply and
release, using an electrical signal from the control unit to the servo valve torque
motor. The pressure flows through the fuses to the shuttle valve module and then
on to the brakes.
Wheel speed signal from the transducer provides the required data input to the
control unit. The unit compares the wheel speed with the aircraft ground speed
to provide a control signal to the normal and alternate valves. The valves limit the
pressure to the brakes.
- 74 -
rnoodull l A-1325
AUTOBRAKE SYSTEM
The AUTOBK ANTISKID TEST IND 1 and AUTOBK ANTISKID TEST IND 2 circuit
breakers provide 28v dc power to the AUTOBRAKES selector switch to the control
unit. An autobrake card in the unit compares IRS deceleration data inputs with
the selected deceleration (encoded in the control unit). This results in a pressure
command to the autobrake valve. The valve provides the pressure via the normal
anti-skid valves to the brakes. Two autobrake shuttle valves shuttle pressure
between the normal brake metered pressure output (manual)and the autobrake
pressure output. When the metered pressure > 750psi, either the left or right
shuttle valve pressure switch opens. This results in an open circuit signal to the
control unit to disarm the system.
Both AUTOBK ANTISKID IND 1 and AUTOBK ANTISKID TEST IND 2 circuit
breakers simultaneously provide 28v dc power for the BITE functions. The
control unit provides fault signal to the AUTOBRAKES light and the EICAS
('
.\, display-vial the EICAS computers -. ~
, \
', !'
\ \'
I
) r--~
\
Prior to
,
/'
landing, t h e pilot arms the syst4rq by p?hing the switch a t o r MAX
i ~
AUTO.!dt t o u c h d ~ w nthe
//
, brakks apply ad~$o~atically.
1 1
I I i i
Should A failure occur, the systfni disarm$ +d the selector ~&tch automatically
movpsl t o ' ~ 1 - S ~ R M
At. DISARY,' tficsystkm,teleases the a u t ~ b r a k epressure, a n
A U T O B R P ~ K E Scomes - - ~ ~ on
~ ~'and-t-he-~~d~~
~ display will s h o w d e AUTOBRAKES
advisory message. The pilot can turn off the AUTOBRAKES light and remove the
message by placing the switch to OFF. The light will not go off and the message
will remain if the solenoid valve on the autobrake module is faulty (solenoid valve
output pressure switch shows high pressure).
Autobrake Deceleration
Selector Pressure Level
Switch At (ft/sec/sec)
1750 5.0
-. -
I I
The system arrns and latches with a magnetic latching switch within 100
milliseconds when the following conditions are met:
The control unit provides an arm hold signal to the switch magnetic latch to keep
the switch in the selected position when the above requirements are met. If the
arm hold signal is not present, the switch moves to DISARM.
The control commands brake pressure by opening the solenoid valve and
modulating the control servo valve as required when:
1. Autobrake is armed.
2. All thrust lever switches are not advanced.
3. Aircraft on the ground, indicated by one airlground signal
continuously for 0.2 seconds.
4. Wheel spin-up circuit activated.
Loss of conditions 3 or 4 above after autobrake application causes auto-braking to
be removed but not disarmed and the time delay resets.
The spin-up circuit includes a detection circuit and a latch circuit. The detection
circuit activates when the average velocity of all wheels is 60kt or above and
deactivates when the average velocity drops below 30kt. The latch circuit latches
three seconds after the aircraft is on the ground and the detection circuit is
deactivated. The latch circuit resets (unlatches) when a ground-air transition
takes place or the autobrake system is turned off or disarmed.
r -- - -\
. \
-- -\
, /
I I
-- " / ' I
1. 1 System is selected off .r__-- < ,
_ _ _ / '
2 . Either left or right rhetered p?ys+ure switch indicbtFs-pres<ure
1 1 (manual brake application) of 75ypsi. 1
3. ~ n d t h r u slever
t switch indicates;advanced on the ground, except that
i any thrust lever s q t c h indicating advanced for Jp 3 seconds after
- - -t&chdown will not idibarm-tlie,dystern. ' '7 pressure
4r -Autobrake fai1uredeteeted;-iniluding failure to~applyl
(indicated by the pressure control switch) when application conditions
are met and the commanded deceleration exceeds the actual aircraft
deceleration by more than one foot per second squared for more than
three seconds.
5. Anti-skid failure on normal system detected except for failures on a
wheel whose indication has been deactivated by the control unit
selector switch.
6. Spoilers stowed after having been deployed on the ground.
7. IRS signal not present or faulty.
Operation
The autobrake solenoid valve provides on-off control of normal hydraulic system
power to the autobrake valve module. When a valve driver signal from the control
unit is received, the valve opens and admits system pressure to the pressure
control valve. The servo valve varies the output pressure from the module as
commanded by the control unit to maintain the selected deceleration.
rnoodull l A-1328
The solenoid valve pressure switch senses the solenoid valve position (open or
close). When the valve opens and admits system pressure to the module, the
switch closes to show high (> 750psi) pressure and provides an appropriate signal
to the control unit. The control valve pressure switch senses the output pressure
and provides an appropriate signal to the control unit for autobrake control.
Brake pressure output from the autobrake module positions the two autobrake
shuttle valves to allow fluid flow via the normal anti-skid modules to the brakes.
Two pressure switches on the metered pressure port of the shuttle valves monitor
manual brake pressure downstream of the brake metering valves. When manual-
braking effort exceeds 750psi on either the left or right brake pedal, the switch
opens and provides a signal to the control unit to disarm the system.
SYSTEMS TESTING
A BITE control and display panel and a n instruction placard are on the front face
of the unit. The panel face consists of the following:
-- -
J;
One alphanumeric display - provides readout and identifies the failed
channel.
* One BRAKE TESTIDISABLE rotary switch - allows selection of 1 to 8,
normal system operation test position and an A / B brake test position.
In addition it disables fault indication on a selected-wheel. On aircraft
dispatched with one wheel deactivated, the switch inhibits the inputs
to the related channel, thus preventing the display of anti-skid EICAS
messages and the illumination of the ANTISKID light.
-k
One ENABLE/VERIFY momentary pushbutton switch - used with the
VERIFY switch to enable a system test or brake operational test.
* One VERIFY momentary pushbutton switch - performs a complete
system test or brake operational test when used with the ENABLE
/VERIFY switch.
* One PRESSITEST momentary, 3-position (PRESS/TEST-OFF-BIT)
toggle switch - performs lamp test (switch in PRESSITEST position
and recalls faults (switch in BIT position). The lamp test includes all
segments of display, ANTISKID light and AUTOBRAKES light.
* One RESET pushbutton - clears memory of stored fault information.
Three levels of BITE test are provided. These are system test, continuous monitor
test and brake operational test.
System Test
With both t h e ENABLE/VERIFY and VERIFY switches pressed and the BRAKE
TEST rotary switch in the NORM position, the control unit performs a complete
system electrical test and sends its results to the BITE. When a fault is detected
the test identifies the failed LRU on the display. When the VERIFY switch is
pressed and released again, subsequent faults will be shown until TEST END is
shown, indicating no remaining faults.
The control unit checks the valves and transducers for continuity and the control
circuit for proper functions.
I
Y The control unit checks the anti-skid valves (normal and alternate) by monitoring
a small-voltage, which it applies-to-the-valye torque motor. This voltage causes the
anti-skid//Gdve torque motor %a~ure-to,be biased slightly; away-from'the
\ I
I
I
! I
I
i I 1
---<\
fully blocked. This allows full prbsbure to't~e brakes.
I
I / /
/ / / 1
I I
The test stores the following detected faults (continuous and intermittent):
* Failed transducers.
* Control circuit failure.
* Faulty valves.
* Parking brake control/parking brake valve disagreement.
* Wheel deactivation.
~r Loss of IRS signal.
Faults are stored in non-volatile memory for readout during ground maintenance.
The memory can store data for a t least 250 hours without power.
Memory recall for fault readout requires placing the PRESS/TEST switch a t BIT
and releasing; this shows the first fault. Subsequent BIT selections display any
remaining faults until TEST END is shown. The RESET switch clears memory of
all fault data.
Brake Operation Test
The test checks the skid release feature and allows a visual brake check. The
visual check is on a single wheel for the normal system and on a wheel pair for
the alternate system. The test starts with the BRAKE TEST switch selected to one
wheel and the ENABLEIVERIFY switch pressed. Pressing and releasing the
VERIFY switch causes a one-time brake release and re-application for the selected
wheel (normal hydraulics) or wheel pair (alternate hydraulics).
* C=ds i~ i ~ ~z ir tnn~ratincr
~
-r--I'- --------- J
nnrrnnllv
'
- -
BITE Logic - -
The communication port in each wheel card provides the tie-in between cards. A
BITE status circuit processes the incoming signal in and out of the self-test
circuits and provides a BITE status output to the driver circuit. A second BITE
status output is OR'd with a failure signal input from other wheel cards to provide
a driving signal to the driver circuit.
The interfaceldisplay card receives front panel rotary switch position discrete
signals to the panel switch input port. The display card also receives the
autobrake discrete signals, the system fault signals, through the BITE/display
port.
The display card, through data management, processes the discrete and fault
signal inputs into the microprocessor.
The rotary switch position discrete signals allow the test initiation circuit to
generate request commands. The commands are appropriate to its mode of
operation (test level) to the wheel cards and autobrake card. On receipt, each card
responds with the status information requested.
When a fault is detected, the display card stores the fault in the memory and
provides driving signals to the display driver and the fault light driver. The display
driver enables the illumination of the display on the control unit (upper half of the
display comes on immediately and the lower half follows after three seconds). The
fault light driver receives the signal from the fault memory and turns on the
ANTISKID light.
I -- - -
- - ~
: I- - ------..\ -..~
+, /- . - \\,
-\ . '\
s,'
\
~.
I,'
\
j,,
1 ' i
I
i
The B$E self-test circuit in each %heel c$djProvides a corndleie electkick self-
test to t h e anti-skid system. Th< tesl-includes / component check for continuity
and i4pedance, driver check foi circuitfdlqre and a brake rkldase-t&s>;Results
of thes!e tests are passed on to t h e BITE c\ard\via the data link
I i
I '
,A:
:I
. ,1
$ 1
', ',
The BITE status,;t,est circuit in ehch wheel k d d provides a rndnitoring test on
/
completibn of t h e self-test. The jebt monl;tbr9 the following &dl provides its
i _--/ , ' I, i-l 1 ,
results to -
the--
BITE card: ,-I
.- _.I \.-
--p
- L," L
The analogue signal inputs from the wheel card to the BITE card are the wheel
speed transducer voltages, the 26v dc and 5v dc regulated power source voltages
and valve voltages.
The BITE self-test circuit in the autobrake card provides a compete electrical self-
test to the autobrake system (aircraft in the air with the AUTOBRAKES selector
switch a t 1, 2, 3 , 4 or MAX AUTO). The result of the test is passed on to the BITE
card via the data link.
The BITE status test circuit in the autobrake card provides a monitoring test on
completion of the self-test. The test monitors the following and provides its results
to the BITE card:
j:
Deceleration selection - a deceleration selected.
* Solenoid and servo valves - continuity and impedance.
* Failure light drivers - continuous operation of light drivers.
* Digital parity - check digital word parity for correctness.
x
Digital checksum - active location check.
* Throttle switch - continuity.
* Airlground sensing - continuity.
The multiplexer in the BITE card selects the analogue voltages to be monitored. A
continuous monitor test circuit receives and processes the voltage signals (valves, {
transducers, 26v dc and 5c dc regulated power sources and faulfiemory power),
the digital memory data and the system status input. The test circuit provides a
time delay of all voltage failure indications as required by the logic circuit. The
data management in the BITE card microprocessor allows a bkffered flow of
signals between the BITE card and all other cards.
--
When the ENABLEIVERIFY switch and the VERIFY switch on the-control unit are
pressed, the BITE card starts a system test (BRAKE TEST switch a t NORM) or an
autobrake test (BRAKE TEST switch a t A / B and AUTOBRAKES 'selector switch in
any one deceleration position). Failure detected during test i s recorded in the
memory and shown on the display. Successful tests feed no fiult signal to the
BITE card and the system is operable.
The system turns on when the switch is in the ON position. The system turns off
when the switch is in the OFF position. Anti-skid system off is shown by the
illuminations of an amber light on the switch, ANTISKID light on P5 and the
ANTISKID OFF advisory message on EICAS display.
When normal (right) hydraulic system power is removed, the alternate (left)
hydraulic system activates automatically. The system provides hydraulic power to
the alternate anti-skid system.
The front face of the control unit contains BITE switches. These switches are used
for checking out transducer, valve and skid circuits on each wheel. A complete
anti-skid system test can also be performed with the BITE switches.
moodull l A-1333
Control - Autobrake System
,
. .- ---.
-
- - ..--.
- --. \
I i
-\\
-.\. ',,
L.
, , ',
i ! ,
, I , \,,
II ,,,,,,,,,,,,,,.,,+
3
i j
\%\
i \ '
' I
, ,
I;
~I I * j , ,
j ;, 1I
i , ,
! , ' i
8
i i , :
I : -.'
,
'
/ 1
I '-.- :
'
I
.----‘i
".;
-
7--.
I \, - /'
i
1 1
8 ,
! !>
~ 1~
1
, .
i !
I
i
i
!
!
!
'\$I
,
,
:
1': ;
I
,
I
i
,
I
.
i
i ! ,/ ,i' I j / 1 /!
r--'
;
!
j
L.-/'
, ,
,-~,
!
I
.1 ..-' ,
/
i
i
!
,I .
I
'. -
- 83 -
moodull lA-1334
/
LBP Dee 03 - Feb 04 - April 04
',
--
NOTE: I t is possible that some of the above statements may not be too
meaningful when read out of context, so it is suggested that the appropriate
book/subject be read first then'the information above be checked against that
CONTENTS
Page
Aircraft lighting 1
Incandescent lamps 2
Halogen lamps 3
The fluorescent tube 4
Light emitting diode 5
Flight deck lighting 7
Integral instrument lights 8
Pillar lamps 8
Ligh tplates 9
Beta lights 10
Floodlighting 10
Utility lamps 13
:(
Control of flight deck lighting 13
--
Passenger cabin and cargo ligh'ting
- 18
-- -
P,assenger area lighting 18
Control of fluorescent tubes 20
Reading lights 21
Attendant call 23
Cargo compartment lighting 25
- --
Other area lighting 25
Exterior lighting ' 26
Legal requirements 26
Navigation (position) lights 27
Anti-collision lights - - 30
Xenon flash tubes ---- - - 31
Landing and taxi lights 33
Other external lights 35
Emergency lighting 36
Floor proximity lights 37
Emergency exit signs 39
Slide and door illumination 40
Lighting control 40
Testing 44
Answers to self assessment questions 45
moodull l A-1336
AIRCRAFT LIGHTING
Exterior Lights. Exterior lights provide illumination of the ground during landing
---J L--F:---=---c:,,,
cu~uLMI
A
,
U ~ C L ~ L L U ~ L allu
D
,-I,,
LlLahr; ~llc
---- r~ -y- : -1: t-- 11- ~ 1 1-111
a l L ~ l a l L ~
n:-LC
I I I ~ I I L a3
,
- 1-2-1-
l ~ l u
A :-- -
LI-
u u w l l ILL LIIL
ANO. provision is also made for thelllumination of tailplane logos and the
requirement h a s to be met for ice inspection spot-lights.
I
I 1 I
_-'
\
\
The operation of the bulb is essentially very simple. An electric current is passed
through a thin tungsten filament (diameter about 0.Olmm or 0.00004"). This
gives the electrons a higher energy state and increased motion. This increased
motion causes the conductor to heat up.
Electrons only remain at a higher energy level for a short period of time. As they
return to a lower energy level, the excess energy is shed in the form of photons
of light. This gives the appearance of making the filament glow 'white-hot'. The
filament is carried on glass mounts to prevent temperature transfer. The ends of
the filament are welded to thicker support wires that hold the filament in place
and provide a current path.
~neb~;
The filament is formed into small coils, mounted onto glass rods and the lot
encapsulated in a glass cover. The glass cover is then filled with the gas as
required a n d cemented to the base.
SAQ 1
In the early days of development the filament was placed in air, but would
quickly oxidize and burn out. How is this prevented in a modern lamp?
rnoodull l A-I338
The base supports the wires, has contacts located in the base a n d provides
support for the assembly in the light fitting. Methods of fixing include screw and
bayonet connections.
The incandescent lamp is only about 5% efficient with most of its energy being
lost as heat and invisible radiation. A more efficient option is the halogen l a p .
The halogens are a name given to a group of elements that have a valence orbit
with one electron missing - fluorine, chlorine, bromine, and iodine. On the
periodic table they fall vertically underneath each other, one space to the left of
the inert gases. What t h a t means is that in any reaction they want to gain one
electron.
Metals are the opposite; they have a valence orbit with one or two electrons and
as such want to give u p a n electron in any reaction. When halogens and metals
a r e brought together in the right conditions they will react - one giving and one
,' t&ir,g, =d XI ionic S c ~ is d fc-ed. - , -- - .
--- . -- -
>
'
Lamps of this type have a quartz envelope and are halogen filled. A commonly
used fill is iodine. During use the tungsten filament vaporise;~slowly and under
normal circumstances deposits itself on the envelope inner face, t h u s reducing
the light output. The halogen fill keeps theJenvelope clean by chemichl reaction
with the deposited tungsten v a p o u r ~ T h ereaction actually goes% stage further
with the vaporised tungsten being re-deposited on the filament, t h u s extending
its life.
I
The halogen lamp tends to give a harsh bright light. This is excellent for outside
work b u t is undesirable for interior-u&. _ - .
(Some car manufacturers have started using quartz iodine lamps as headlights.
The same is true on aircraft with landing lights etc).
Care needs to be taken when replacing this particular type of lamp as the
natural oils from the skin will be deposited on the outside of the envelope. This
will, during normal operation of the lamp, sink into the envelope and seriously
shorten the life of the lamp. Always wear suitable gloves when handling the
lamp.
Note. Most lamps get very hot when on. When changing a lamp always switch
off some minutes before attempting to complete the task to allow the lamp and
housing to cool. If there is no time to allow it to cool then wear protective gloves.
- 3 -
moodull lA-1339
The Fluorescent Tube
Figure 3 shows a schematic of a basic fluorescent tube. The tube is filled with
mercury vapour a t a low pressure and sealed at both ends with a cathode and
an anode. The inside surface of the tube is coated with phosphorescent metallic
salts, s u c h as zinc sulphide or zinc silicate. Note that it will require a n
alternating current unlike the incandescent lamp which will work with ac and
dc.
Electrons are emitted from the incandescent cathode (not bright enough to
illuminate anything - in fact some tubes are cold anyway). These electrons have
tremendous energy and will aim for the anode a t the other end of the tube.
Movement will be from the cathode to the anode (dc),but alternating when the
supply is ac. During their journey they will collide with the mercury vapour
atoms in the tube. These collisions cause radiation to be emitted, which is
mostly all in the invisible spectrum (ultra violet).
The visible portion of the radiation is a pale colour in the blue green range. Th-
ultra violet (invisible) radiation will strike the phosphorescent coating on the
insidyof-t3e tube and cause it t o emitradiation with a longer wavelength and
more i ' p ~ r t a n t l y , a wavelength t k a P i 3 i n the visible spectrum. During the
collisi?n other electrons are emitted and move on towards the anode, colliding
many times before getting there. I
' ,
I 1
- .--
I
----
SAQ 2
1 1 1
I
I
b I I
If a n ohmmeter was placed across an incandescent lamp a n d then placed across
a fluore$cent filament, what results would you expect to see?
/ 1
\
-
-
- - - -
Providing the current is already flowing, a n d the collisions are taking place
electrons will be moving from/to the cathodelanode and as such the tube (once
started) provides a very low resistance. So how do we initially get things started7
This is where the choke (sometimes called a starter) and the auxiliary lamp
come in. The choke is a n inductor which prevents dangerously high voltages; it
also acts in the starting cycle.
When current is first switched on the glow lamp lights due to the fact it is in
parallel a n d the bimetallic contacts are a t this moment open. The bimetallic
contacts now close and allow the full current to the cathode which makes it
incandescent. The bimetallic strip now cools and breaks; this breaks the action
of the choke and causes a voltage spike that forces electrons to be emitted from
the hot cathode.
The cycle h a s begun and current flows in the main tube and no current flows to
the auxiliary lamp and so the bimetallic contacts remain parted.
Cathode
f
"-1 Tube
I
4
1
w
electrons
-
V BI metalic
contact
Glow lamp
Glass envelope
,+rvf B - GPE;aTiGIi
--
Fig. 3 FL';'BRE8cENT
-
- - -
\ \
Careful selection of the fluorescent material can make the light glow in virtually
any colour. The most common is as described and this produces a moderately
white light. A s the light is caused by radiation from collision ,rather
--
than a n -
energy change (in the case of the ifL%ndescknt lamp) it is very efficjent once
started. It produces little heat m d so doesn't add to cabin heai sink.
Due to the alternating current, the lamp can have a moderate stroboscopic
effect and b-ecause of this and the fact-that is produces a harsh light, its use on
aircraft tends to be limited to the cabin spaces, where they>re.6ed extensively.
They require a ballast transformer to raise the voltage sufficiently to provide the
ionising effect required to excite the tube. This transformer is also used to
control light intensity, as we shall see later.
If you have already studied modules 4 and 5 then this should be mostly
revision, if you haven't then this might all be new to you and you will require a
bit more study time.
LED'S operate on the principle that under forward bias conditions a p-n
junction diode exhibits special properties.
Electrons are easily driven from the n-type material into the p-type material by
the electric field applied. The reduced depletion area that exists allows the
electrons to travel quickly from one to the other. Upon entering the p-type
material, but still close to the depletion area, the electrons meet a plentiful
supply of 'holes7t h a t allows rapid combination. The electron is now returned to
a lowered energy level a n d the excess energy is shed in the form of a photon of
light energy.
Careful selection of materials determines where the emitted radiation falls in the
spectrum. Gallium arsenic phosphide is a common semiconductor used to
provide an orange indication. This colour can be changed with the use of a filter
or different material construction.
That is a brief description of a n LED and should you require more detailed
information you should refer to the EASA module 4 and 5 study books.
I I
1 LENS I
- ,
I TRANSLUCENT
I PLASTIC CASE
1
_,
FLAT
- --
CATHODE
CATHODE ANODE
LEADS
We shall leave it there for the time being. There are other forms of light devices
and we shall be briefly discussing those as they come up.
Try the following exercises. As usual the answers will be found in the text.
- 6-
rnoodull l A-1342
Suggested Practical Activity (if access and equipment allow):
With the lamp removed from its socket carry out a resistance check of a known
good incandescent lamp and note the reading. It should be typically about 5R.
Check the resistance of a 'dead' (open circuited) lamp and note the reading.
In a dark room switch on a domestic fluorescent light. Watch for the auxiliary
glow lamp illuminating just prior to the main tube flash over.
The requirements for aircraft lighting are laid down primarily in the A N 0 and is
further expanded on in CS25.
Adequate lighting must be provided so the crew can see all the controls and the
instruments a n d the markings near to them. Anytime the aircraft is or is likely
to enter Instrument Flight Rules (IFR) the instruments will require illumination.
This illumination will need to cover the possibility of operations in dull daylight
\
L1ll uug;i dusk tu coiiipiete
~1
"1- - -- - --
--L-:-- A ~ r r- :-
"---A - - - - - ---
1 L ~ CL + ~ L C L L H ~ L L U111 3~ u 1 1 1 ~ t ; i - i ~ w
~a y ~ ltu
-1
ib
-
--
alter illumination levels. All this needs to be catered for.
' I
- .
Flight deck lighting includes:
* Floodlights. Used for general lighting of the area. The main
instrument panel floodlights are controlled from switches on the
lighting panels. These lights may be fluorescent tubes or ordinary
- l a m p s . Some flood lightslike-glareshield and aisle floodlights are
controlled from rheostats.
* Integral Lighting. Lighting for all the instrument and circuit breaker
panels is controlled from the lighting panel. The bulbs used for
faceplate illumination are usually soldered onto a circuit strip
attached to the rear of the instrument faceplate.
~r
Miscellaneous Lights. Map lights illuminate the pilot's lap area.
Chart lights illuminate the pilot's letdown chart holders and utility
lights that are moveable are for miscellaneous use.
* Override Light Switch. The override light switch can be used as a
means of turning on all of the instrument panel floodlights from one
switch.
* Standby Lighting. With only standby power available certain critical
lighting circuits revert to standby power sources to provide
emergency lighting.
~r
Master Dim and Test. The master dim and test provides night
annunciation light dimming and a convenient 'one switch' test of all
appropriate lamp annunciators.
We shall spend some time dealing with lighting based mostly on Boeing aircraft
but the principals are similar for all large commercial aeroplanes.
Each instrument has its own integral lamp with the wires run to the back
connector of the instrument casing. A plug will then connect the larnp to the
aircraft lighting system. The circuit will include a common switch, fuse or C / B
and a dc bus bar.
The filament lamp is so positioned that it shines onto the face of the instrument,
yet doesn't show any glare.
-8-
rnoodull l A-1344
Often two pillar lamps will be fitted over the primary flight instruments, thus
providing a degree of redundancy. Replacement of the bulb is simple enough
with the cap being held in place with a spring collar. Once this is removed the
sub-miniature bulb can be removed. The cap alignment is crucial as this
determines the light effect; the cap is keyed to the pillar.
An improvement of the pillar lamp came when two were located together on the
same housing. This made for easier maintenance. Sometimes called a bridge
lamp.
reflecting surface the light will be refrairtedout of the plate and-become visible.
~ r bU"
"tL the
-~c\-n-\rr
1 "'"
I
I
I
I Scratch
location I
Pollshed sqrfa'ce
There is a limit on the distance that a small incandescent lamp can work to, so
to provide good panel illumination on larger panels a lamp has to be placed
every six to ten inches (15mm to 254mm). The lamps are identical to the small
filaments of the pillar type lamps and are similar to replace.
-9-
moodull l A-1345
White coating (allows Plastic laver
reflected-and (blocks light) Threaded Cover
refracted light)
\ I Rubber
Shroud
With a n increase in bulb life, it h a s become possible to insert the lamps into the
panel itself. There are more lamps fitted than is actually necessary to provide
the correct level of luminescence and this allows for some failures. In this case if
there is a problem with the lightplate, the whole panel is replaced. Again with
modern-aircraft this is not so ,demanding on maintenance due-to the BITE that
most-systems have, making such a-replacement possible in,a matter of minutes.
I
\
I
A further development i s to replace the incandescent bulbs with LED's. LED's as
you know have an almost infinite! life and 9s such the problems of illumination
I .?
source fylure is largely eliminated. -
-1
I II 1- , Y \ /
Not veryfcommon but you may come across,them. Unlike other lights on the
flight deck therelare no ON/OFF switches, these lights are o n all the time.
- - ---- - -- ---- --
They work on a principle of producing Beta radiation from the tritium and
fluoresing, in a way not too dissimilar to the principle a fluorescent tube. They
tend to be used (if a t all) in emergency light packs and to show a route to a
torch for example. Also used on some avionics equipment.
They need care and attention when replacing. A s a general rule they are not
dangerous providing that the glass is intact, but if this should be broken clean
u p all glass carefully ensuring that no dust is inhaled. Follow the procedures
laid down by your company and if you are cut with the glass (the same as with
fluorescent tubes) you should seek medical attention. They are, as their name
implies, mildly radioactive.
Floodlighting
Floodlighting is a general term used for the rest of the lights i n the flight deck,
however these can also be used to illuminate instrument panels.
I t is not uncommon for strategically placed floodlights (under the glare-shield for
example) to be used to illuminate the instrument panels. Sometimes lights
placed in t h e ceiling area are directed down to illuminate the centre console.
Figure 8 shows a typical floodlighting arrangement and figure 9 shows a typical
light controls layout. You should note the different types of lights and their
location. All these lights are of the incandescent filament type, although a t least
one manufacturer uses fluorescent emergency 'dome' lights.
Sometimes the dome filament is a different lamp to the rest as it has two
concentric filaments, one for normal use and the other for emergency lights.
NAP LIGHT
\
SAQ 3
Why use incandescent lamps instead of the more economical fluorescent tubes
in the flight deck area lighting?
Figure 10 shows some of the different types of lamps and their respective
holders. For control reasons the flight deck is separated into sections and a
control is provided for each section. All floodlights can be controlled
independently or collectively. The collective control is often referred to as 'storm
lights', a n d pressing this button will put on all the flight deck floodlights a t full
illumination. There are many variations in flight deck lighting so you should
refer to the specific AMM ATA chapter 33 prior to any maintenance or replacing
any lamps.
- 11 -
moodull l A-1347
AISLE STAND
'FLOOO LIGHT
--
'1 -7
\ ----, -
I I
Fig. 9 TYPICAL FbIGHT DECK LIGHTING C0,NTROLS
I
' I
I
1 I
l
I
i
-
<.
- 12 -
moodull l A-1348
It is a requirement of t h e A N 0 that the aircraft carries on the flight deck 50% of
the total number of lamps used on the flight deck as spares. This affords the
crew the chance to replace any lamps that might fail in flight. This occurrence
should be notified to the maintenance personnel by the crew, entering the fact
in the Tech Log sector reference pages.
Most aircraft are required to have, somewhere on the flight deck, a t least one
utility light (see figure 11).These are a simple incandescent light connected with
a coiled extension lead a n d a control switch on the back. Adjusting the focus is
by movement of the front ring.
Usually powered from t h e hot battery bus (28V), which effectively turns them
into a n emergency lamp a t the same time. (For details of dc power distribution,
refer to the books in this series on electrical power).
LIGHT- --
CONTROL.
RETAINING
R1NGY3
Fig. 11 UTILITY LAMP
This is usually done by altering the voltage to the lamps (the output of
incandescent lamps is more or less directly proportional to their input, except
for some heat and resistive losses, that are not significant in this application.
For a dc supply a variable resistor type of dimmer control is used and for a n a c
supply a variable transformer is used. (See basic electrical theory module 3 for
details of how these operate).
Flight deck lighting control is more complex than it seems (figures 12 and 13)
and usually involves:
* Each panel or instrument cluster or map or chart or floodlight h a s its own
individual control.
* There is a master control that will brighten all the instrument lights
together.
* Often a n override switch is provided to allow full illumination of all the
instruments immediately.
I
I
I ,
'F&. 12 BRIGHTNESS CONTROL - EXAMPLE
I I
- - - -- - /
-- --- -- - --
To cope with these requirements there are several dimmer controls located a t
various locations around the flight deck. Figure 9 shows a n example.
Figure 12 shows a circuit taking 28Vac from the ac transfer busses. Variable
auto-transformers provide adjustable brightness control. This output is further
reduced to 5 to 0 volts by additional transformers.
Figure 13 shows another example of a control circuit. Note the 28Vac supply
from the ground service bus and battery bus with dimmer control for the first
officer's and captain's dome lights via the dimmer light switch, the dome switch
and the flood dome switch. Note the 28Vdc standby supply to both front domes.
18V AC
l4
5101 lL,%3DoME Lls L4I A l l 111 OK
DOYI
Z 1 V DC
Is"I' l W O O O l l l 11s
111 4 CIRCUIT B A E A K I R
L Ir~
l o s OOUI
1111
UIMSI nltnr LIOHTIHG CONIROL IPSI
r i t G n l COMPARIMENI OOUI t l e u i
-- --
131 - ---
. -.
.
\
- - -
'
Fig. 13 EXAMPLE - FLIGHT DECK DOME LIGHTING
Figure 14 shows a more modern light control circuit. Switches alter the control
voltage and sends the modified voltage-to'a\dimmer control unit:-(There may be
a large number of these located behind the flight deck consoles - t h C ~ 7 7 has
7
14 for example). The dimmer contxol unit uses this voltage to alter the low
voltage output to the instrument panel lighting.
A similar function occurs in the dimmer control unit for the'slightly higher
voltage floodlights that are u s e d ~ f o ~ i n s t r u m eand
n t panel illumination. It is not
normal to control area floodlights (sometimes referred to as dome lights) in this
way, especially as sometimes they are fluorescent tubes.
Pressing the master dimmer control will override all the control voltages and
apply a maximum voltage to the transformer windings and bring all the
instrument a n d panel illumination on to the highest level.
Figure 15 shows how Airbus vary the applied voltage to the dome lights without
using any direct voltage control. The initial supply is 28Vdc to switch 5LE with
DIM, BRIGHT and STORM settings and to switches 5LE and 19LE.
Each dome light has four halogen long life (about 2000 hour) bulbs.
MANAGEMENT PNL
TO STBY INSTRUMENT
LIGHTS (P2)
PNL LT DIMNER
MASTER BRT CTRL & SU CTRL UNIT
m T - L I G H T I N G CONTROL
S!!:!lN:?,!Tf:!k":PN:kUb?GYr:!
.nI""I., YI..LI.-.a.ILYI.~L . ,.l.k.. b-.....
S::SHfJr
--.."--.-
(OUTER KNOB) ARE SIMILAR \
-- --
601PP
+2BVDC
403PP
+28VDC
L------J
5GA1
When the switch is in the DIM position the light decreases. In the BRT position
the lamps are supplied in parallel (26V) and in the DIM position they are
supplied in series in groups of two. This means there is a reduced voltage drop
across each lamp.
When the switch set to STORM all lamps come on a t maximum brightness.
If the main b u s is lost only dome light 452VU remains operative via the
essential bus.
On the ground, in the acceleration stop configuration, the dome light 452VU is
automatically activated what-ever the position of the switches.
Also on the flight deck are lighting strips each with four 28Vdc halogen 11.5W
lamps controlled from a simple ON/OFF switch.
', - - - -
-
-
I I
For some instruments (typically items like audio selector panels and radio
panels) the illumination is controlled automatically. Instead 'of using a control
voltage from the dimmer switch an amplified signal from a photosensitive
-
cell is
used. I I
The photo (light) sensitive cell is positioned in such a location that, as the
ambient light-increases, so too does theyoltage from the cell, a n d this through
the d h m e r control units, increasesthe voltage and hence illy&bation of the
instruments. A s with other flight deck lighting this can be overridden to full
illumination by the selection of the dimmer override button.
That covers flight deck lighting. We touched briefly on emergency lighting and
shall return to it later. Now try the following exercises. A s always, the answers
are to be found in the text.
Locate the flight deck lighting controls, see how many there are and what effect
they have. Check on the flight deck lights and identify the various types used.
Spend some time looking through the maintenance manual chapters that are
relevant. In this case ATA33- 11.
SAQ 4
What is the most likely style of lighting to be found in the cabin area?
We have covered most of the area lighting system concepts when dealing with
flight deck lighting, and passenger area lighting is virtually the same, though
rhere i s ~ o n s i d e r a b i yiess cuniroi.
/ -A
--
1
I i
Area Lighting' :
----- - .-- --
Figure 16 shows a general arrangement of a passenger cabin lighting system.
The main stay of the system are the fluorescent 'washlights' and ceiling lights.
These operate a t one of two levels, bright and dim. Also you might expect to see
incandescent night lights, doorway entry lights and reading lights.
In the galley areas there are some work-lights (spot lights) a n d area lights, these
being a combination of fluorescent tubes and incandescent lamps.
Control of the cabin lighting is from the area control panels located a t the
attendant locations. This may be through software related systems (on newer
aircraft) b u t equally through traditional rotary switches as found on most older
aircraft. The control range is often as follows:
OUTBOARD
STOWAGE
BIN
OUTBOARD
PSU
SIDEWALL
P 3 2 0 GND HDLG/SVCE
PWR PANEL
Figure 17 shows a switching system for the control of side-wall lights, ceiling
lights and night-lights. The lights are controlled through a software package
inputted from a n area selection panel located in the attendant's area. Physical
switching of the lights is carried out through transistor action remotely.
The fluorescent tube consists of a tube and ballast, with a power supply. The
ballast is a transformer that steps the voltage u p to that required by the tube to
operate. Normally the ballast outputs 205Vac to the tube for 'dim' lighting and
adds a n additional 115Vac for 'bright' lighting. It is usually possible to bypass
the switching system and provide 'full' power lighting from the ground service
bus.rrhis-faciiity aiiows the aii'craf~-m
7 , be cieaned and serviced wiihoui ihe rriairl
system Gower having to be on. [ --'
'
;
I
I
I
I
I
i
PART
/"REE::Ak:NS
uCONTROL
PASSENGER LENS
UNIT
- 20 -
moodull l A-1356
SAQ 5
A ballast often h a s two tubes supplied from it. How can this help in terms of
fault diagnosis?
Reading Lights
Most seats are provided with reading lamps. These are usually fitted as a 2, 3 or
4 lamp module in the ceiling panels immediately above each seat group. Some
seats have individual stork mounted (or swivel mounted within the side head-
rests) reading lamps attached directly to the seat, these are low voltage supplied
a n d are individually switched. Figure 18 shows examples of those fitted above
the passenger seats.
TX-
D C GND
RX-
I I
PASSENGER S E R V I C E UNIT
The lights are usually of the incandescent type as they are easier to control.
Operation of the lights above the seats is initiated by pressing the light control
button on the passenger control unit located in the seat arm-rest. This sends a n
ON/OFF signal (typically through a n ARINC 429 data bus routed within the seat
tracks in the floor) to a n electronics unit a t the front or rear of the cabin. This
sends a signal through the control line above the ceiling panels to the individual
De-coder/En-coder Units (DEUs) above each seat group. This signal is decoded
in each DEU and that switches on the appropriate reading light for that seat.
moodull lA-1357
The Control and Display Unit (CDU) on the flight deck is used to BITE test the
system when the aircraft is on the ground. The CDU sends a signal to the
electronic control unit which transmits a signal to each DEU. The DEU puts the
system to test mode a n d puts power on to each lamp for a short period of time
(the lamp should light for a moment). Normal switching is un-available during
this time.
Test d a t a is stored in the BITE memory of the electronic control unit and is
displayed on the screen of the CDU. It will indicate if no fault is found, and if a
fault is found will give the location of the unit that is not operating.
The attendant call system provides a method for the passenger to get the crew's
attention should they require assistance.
LAVATORY
- 23 -
moodull l A-1359
Call buttons are fitted to each passenger seat control unit (in the arm rest), or
above each seat, a n d located in each toilet cubical.
At the attendant locations and often above the emergency exit signs a series of
indicator lights show. These display blue for seated passenger requests, amber
for toilet requests and pink when the attendant's internal phone is ringing. In
addition to these there are chime speakers above the attendant locations.
-- --
Briefly the system operates as follows. The passenger presses the button in the
lavatory (or seat location); this applies a n earth to the respective overhead
electronics unit and the zonal management unit. These earth triggers and
latches solid state devices that put the light ON above the toilet
door/appropriate seat and the master lights at the attendant's station. Also (not
shown in figure 22) the chime will sound.
The attendant goes to the location, addresses the passenger's needs, then
presses the reset button which cancels the demand and clears the latches. All
lights go out and the chime stops. The reset can also be performed from the
main terminal should the need arise.
--
34 -
moodull lA-1360
Cargo Lighting
Figure 23 shows the general arrangement for cargo bay lighting. It will consist of
either recessed incandescent lights or the flush fitting fluorescent type.
CARGO
COMPARTMENT
\ LIGHT (TYP)
\
-- -
The lighting for the cargo bay is controlled from one switch located close to the
freight door. The power to this switch is usually controlled to prevent the bays
from being powered in the air. TherdBi'e several ways of doing this, but a
common one is to provide a g r G n d handling ac bus that is airground sensitive
(ie it loses power with weight off the wheels).
The lighting i s usually made u p of a large number of lights in the ball transfer
mat regions a n d the area where the cargo comes into the aircraft. The area
going down into the aircraft hold tends to be less well lit. In addition a light is
provided that shines onto the pallet loading truck. This light will either be
positioned outside recessed into the fuselage or on the inside of the cargo door
(remember of course the door is u p during cargo loading).
It is usual to provide lighting around the aircraft in all the servicing bays, wheel
wells, APU bays etc. These are always incandescent lamps with a switch located
nearby. A s with the freight lighting, these will extinguish as the aircraft becomes
airborne, though of course, they should be switched off before push-back
anyway.
That concludes this short chapter on interior lighting. Now try the following
exercises:
Look in the AMM a t the relevant chapters for cabin and cargo lighting. Study
the circuit diagrams a n d make sure you understand how the lighting is
controlled, a n d any tests that can be carried out.
Have a look at the types of lighting in your aircraft - their location and
operation.
If you.canassist in any rectification work,then do so. Make sure you keep your
\ -
I -.
~ x t e r i b lighting
r is, in si=iZT-to'the other types of lighting on the
aircrag so I shal1,not repeat how it is controlled, but focus more on the types of
lights a n d where and how they ar,e fitted. They include navigation lights, runway
take-off iights, logo lights, taxi lights, wing illumination lights etc .
/ I
- -, .- -
----- -- - - -- -
The Regulations
The A N 0 a n d the associated EASA CS25 define what must be fitted, how much
light must be emitted, in what direction and the colour specification.
- 26 -
rnoodull l A-1362
Position light requirements as stated in CS25, in general, should not be less
than:
* A steady green light of a t least 5 candela to the side (40 a t dead ahead),
showing to the starboard (right) side of the aircraft through a n angle of
110" from dead ahead in the horizontal plane. Vertical plane intensities
are also specified.
* A steady red light of a t least 5 candela to the side (40 a t dead ahead),
showing to the port (left) side of the aircraft through an angle of 110" from
dead ahead in the horizontal plane. Vertical plane intensities are also
specified.
* A steady white light of a t least 20 candela showing through angles of 70"
from dead astern in the horizontal plane to either side of the longitudinal
axis.
--
CS25 regulations for anti-collision lights are (in general):
I
--- -
Note. The candela (old name candle which is fractionally smaller) (cd) is the SI
unit of luminance and is based on the light emitted from molten platinum a s it
solidifies at 2042K. At this temperature lcm2 will emit 60cd. (1 candela roughly
equates to a quartz halogen lamp of 20w supplied by 28Vac).
SAQ 6
What implication will the failure of one navigation light have on the continuing
airworthiness of the aircraft? What type of lamps would you expect to find being
used for external applications?
Figure 24 shows a general view of all the exterior lights on the B777. Take a
moment a n d study the drawing.
- 27 -
rnoodull l A-1363
ANTI-COLLISION
LIGHT (STROBE, 3 )
ANTI-COLLISION P O S I T I O LIGHT
~ (5)
LIGHT (BEACON)
Note the beacon anti-collision lights on the top and bottom of the fuselage and
the wing and tail anti-collision strobe lights.
,
7 ,- - ---
Note the wing tip and tail moulte'd pos$iip~lights.
Note alsd the landing lights (4), the taxi lights (2), the turn off lights (2) and the
logo lights (4). -. /I
II - _-
/'
I ' \
i I 1
--
REAR
POSITION
LIGHT
moodull l A-1364
Figure 25 shows the wing tip fitment details for the position and anti-collision
lights.
Another way of providing the back-up supply to the lights is to have a separate
supply of 28Vdc from the battery, This is initiated by switching, in the flight
deck, from ON to ON BATT. Not common these days, but still around.
Figure 26 shows the external light arrangement for a B747. Note the angles for
the position lights (mandatory) and the angles for the landing and turn off lights
which are specific to this aircraft. Their main requirement under CS25 is that
they produce a clear light to light the intended area and do not produce glare for
the pilot. Note the anti-collision lights and the emergency lights.
- 29 -
rnoodull lA-1365-
'?
, ,
-,
,
'
. -
i
. . _ ~
.-~
- -
' I i
i
' !
I i '
I
~nti-collisionLights
i --
The lights must be on anytime that the aircraft is on the airfield with engines
running. In addition the commander must be able to switch off these lights
should the need arise due to glare or flash-back. If the aircraft was in fog for
example the lights could simply 'flash-back' and dazzle the crew.
Power to the rotating beacon is controlled from the flight deck through a relay i n
the power panel. Normal supply would be 115Vac and as with the navigation
lights this supply needs to be protected in some way. Notice from figure 26 that
the reflector emits two distinct light patterns. One half of the reflector is straight
and gives a narrow beam of very high intensity light; the other is curved slightly
to allow a wider less intense light pattern.
- 30 -
moodull l A-1366
MOTOR AND DRIVE
METAL COVER
ELECTRICAL
CONNECTOR
Another type of rotating beacon employs the same principle b u t the lamp unit
itself rotates. The unit h a s two lamps which rotates a t about the same rpm and
the reflector type
Another method of producing a flashing light is the xenon tube gas discharge
lamp.
The flash tube provides a very high intensity light for a short period of time. I t
achieves this by applying a high voltage to two electrodes and then introducing
a trigger voltage (figure 30).
- 31 -
moodull l A-1367
Main
Voltage drop electrodes (2)
'
Rectifier resistors
\
5-H i Ignition ,--- --
Condenser I
n F c
voltage
Step-up
11 1
11 8 I
-
-Main tube
condenser
Ignition
~ynchronisin~ logic
control circuit
REFLECTOR- !Q.
p, LAMP REFLECTOR
@
!- LIGHT ASSEME
RELAMPING
HANDLE1
'-ELECTRICAL
UPPER BODY CONNECTOR
BEACON
WING ANTI-COLLISION
L I G H T (REMOVED)
With reference to figure 30, the flash tube has an ignition circuit with a smaller
capacitor (condenser) and a transformer. This capacitor is charged from a
voltage reduction resistor pair.
- 32 -
rnoodull l A-1368
The synchronising logic control circuit now allows the ignition capacitor to
discharge through the transformer and into one of the electrodes. This induces
a high voltage in the other electrode of about 10,000V. This voltage is high
enough to ionise the xenon gas and cause current to flow. This produces a short
duration high intensity white light, Basically, a streak of lightning has just been
generated, albeit for only about 1/ 1000th of a second. The light is bright enough,
however, to be visible several miles away.
The usual arrangement is for the flash tube to be separate from the rest of the
components. The transformer unit being located close to the light a s from it
comes the high voltage necessary to light the flash tube. Figure 3 1 shows a
typical installation of s u c h as lamp. It contains a parabolic reflector with the .
flash tube wrapped around the inside. Flash tubes can be made to fit any shape
or size.
SAQ 7
L
--
As the aircraft approaches the ground it is dbsirable that the flight crew' can see
ahead. The aircraft is provided with high intensity forward &nting
-
lights to
illuminate the landing area. - - \ ',,
i
Study the circuit and note the use of limit switches to control the range of
movement of the lamp, the two field windings (one up, one down) and the
control of the light itself.
- 7 A
d7 -
moodull l A-1370
Because they are cooled in the airflow when airborne, when on the ground they
are limited a s to the amount of time they can be ON. Duty Cycles a r e normally 5
minutes ON a n d 5 minutes OFF but check the manual.
A taxi lamp (sometimes termed a runway turn-off light) provides the crew with a
reduced intensity light that highlights the edges of the taxiway a n d a n y runway
turn off points. Usually a halogen type of lamp, like the landing lights, but of a
reduced wattage. Again location is a matter of design choice, b u t common
locations are the nose leg or the wing leading edge root.
There are other external lights for a number of reasons, some cosmetic some for
flight reasons.
Wing illumination ( A N 0 schedule 4). Lights are often provided t h a t shine down
the leading edge of the wings. These provide two functions. In flight they can be
k used to help identify ice formation on the wing, a s a back-up to any automatic
\ .
ice detection system. On the ground they provide illumination-of the-,wing
helping to avoid hitting the wing with ground service vehicles etc: . '
I
Logo lights. These are installed in the upper surface of the hbrizontal tail
surface and are designed to shine onto the tail logo. Purely a commercial thing
that allows the airlines to essentially
- -
advertise a s they taxi around
8 - -
airports.
I
I
Caution. When working on lights and lighting circuits it is important to isolate
the power supplies and tag the system to prevent power being re-applied. Lights
c a n get very hot when on (and just after switch-off) and present a b u r n hazard.
With certain lighting systems --xenon.-tubes for example - high-voltages can be
stored within the power circuit so must be left for a period of time after switch-
off before any work is carried out. The 'wait' times are stated in t h e AMM.
There are emergency external lights still to cover, but for now I would
recommend t h a t you consolidate your knowledge before moving on. Try the
following exercises:
Check your aircraft MEL to find out which lights are 'nogo' items.
Look in ATA chap 33-30 a t external lights, find out how lamps are replaced, and
look for dual bulbs and single systems. Study the control schematics to see how
the higher voltages are controlled.
EMERGENCY LIGHTS
The ~ k scale
d Z requires that dufficient lighting be provided both inside and
outside the cabin to facilitate the safe evacuation of the aircraft in a n
emergency..~kis'to be operable.in' the event of normal electrical supply failure.
I
-- --- -- - -,
It (and CS25) requires emergency floor path lighting in the passenger cabin
sufficient to allow evacuation of the aircraft in the dark or in smoke conditions.
These lights may be fixed to the bottom part of the seat structure next to the
aisle or fixed to the floor. On some aircraft they are also fitted around escape
hatches.
- 36 -
moodull l A-1372
Sign letter sizes are specified a s is their colour (red) a n d back
ground colour (white). Emergency signs are to indicate locations of
emergency exits.
* Floor path lighting must be provided so if all illumination 4ft above
floor level is obscured the escape route can still be followed by the
passengers
* Switching by the pilot or cabin staff with switch selections ON, OFF
and ARM. When selected to ARM the emergency lights will come on
automatically if the normal electrical system fails.
* External lighting to include over-wing exits, escape slides and
ground areas around the bottom of slides.
In a fire smoke will rise and fill any room space from the top down. This means
that crawling out of a smoke filled aircraft gives the best chance of survival and
floor proximity lighting is designed to indicate the way out. Figure 35 shows a
seat mounted light and figure 36 shows a floor mounted system.
- 37 -
moodull l A-1373
Fig. 35 SEAT MOUNTED FLOOR PATH LIGHTING
The purpose of the lights, regardless of where they are fitted is to enable a
crawling person to find a way out of the aircraft. They are essential for flight.
Figure 37 shows a typical example. These are situated within the cabin a t
locations to comply with CS25 and meet the requirements of size, colour and
minimum internal illumination.
As with most lights there are many variations on a theme, but the basics are the
same. Note from figure 34 that the sign h a s the words EXIT written in red a n d
an arrow pointing in the direction of the door. The cover panel is removable to
give access to the two incandescent bulbs that run off the 28Vdc supply system
that includes battery packs and charging circuits.
On some, particularly older aircraft, these battery packs were of the throw away
type. Care needs to be taken to ensure that these packs are not inadvertently
discharged. The lights are sometimes paired with a single battery pack and this
poses a problem during maintenance. A paired light sometimes sees the missing
lamp as a power failure and switches on the emergency lights.
moodull l A-1375
Slide and Door Illumination
Sometimes mounted in the side of the fuselage, but also possibly in the
passenger door, the 28Vdc lamp will illuminate the deployed slide and some of
the surrounding area. Lights are also placed to shine on the overwing exit areas.
LAHP LEN'S
i 1
I
I
1
Fig. 38 SLIDE
I
AREA ILLUMINATION,
I
I I I
I ' /
Lighting I ~ o n t r o l
-
1 - _. _ _- i
Control of the emergency lighting is-effkcted from the flight deck by a 3 position
switch (figure 39).
With the switch in the OFF position all the power is removed from the lighting
systems, through relay action in the essential bus breaker box. The emergency
lights will not illuminate a t all. This is the position that the switch needs to be
in before power is removed from the aircraft. With the switch in this position an
advisory message is displayed in front of the crew.
With the switch in the O N position the lights are all lit from the aircraft power
supplies that are available. Usually this is from the hot battery bus (the bus
that is always live whenever the battery is connected) or from the dedicated
battery power packs if this is not available.
To select the switch either on the flight deck or the attendant's panel, the guard
must be de-seated. The middle position and the one that the switch assumes
when the guard is closed is AUTOMATIC or ARMED.
-
P87 ATTENDANT
SWlTCH PANEL
This is the 'flight' position and where the crew place the switch before take-off.
In this position the lights are under the control of relays in-the essential breaker
box. Providing aircraft power is-available &d on, the lights-are-off. Should
aircraft power fail (or be switched off) the emergency lights all come on
automatically. This will drain the qircraft battery power packs within ,about 10
minutes.
1
I .. -
OVERWING BATTERY
EMERG EXIT ASSEM. 2 PLACES OVERWING EMERG
DOOR SWITCH -
LIGHTS 4 PLACES
(2 PLACES)
SW CLOSED - DOOR I N -pJJ
SW OPEN . DOOR OUT
- 41 -
rnoodull l A-1377
The battery packs are on charge when the switch is set to ARMED or OFF with
the rest of the electrical power supplies available.
In addition to the flight deck control a control is provided in the cabin area,
usually at the main attendant's (purser's) location. Door 1 left or 2 left are
typical locations, b u t there are others. This switch will allow the lights to be
switched on independent of the switch position on the flight deck switch.
A test switch may also be provided, this will put the emergency lights on for
about two minutes. This is long enough for all the lights to be checked, but not
long enough to discharge the battery power packs. There may also be a similar
test switch for the exterior lights. Most modern aircraft have BITE systems so
the lights can be checked using BITE.
Figure 40 shows a simplified circuit diagram for the power supplies for the exit
signs, ovenving lights, escape slide lights, aisle lights, and door lights. It also
shows the battery power supply packs (4). Note the switching and dc power
supplies.
---- --- --
-. - -.
EMERGENCY LIGHTING-LOCATION
rnoodull l A-1378
Figures 4 1, 42, 43 a n d 44 show the power supplies and emergency illumination
for the Airbus A330. Study the drawings carefully and check on the component
locations and the system operation. There is no need to remember the details,
but the philosophy is similar for any modern passenger aircraft so you need to
know the general operation.
E X I T SIGN 1
EXIT SIGN 2
FPEEPH 115VAC
(CROSS-AISLE)
FPEEPM ? I S V A C
(MAIN-AISLE)
(WAIN A I S L E )
DEU-B
NOTE: @ SWITCH CLOSED WHEN
- EMER S L I D E RELEASED
- 43 -
moodull l A-1379
NORM BUS
E3 E X I T SIGNS
@ CEILING LIGHTS
; a<
-
28VDC GND WHEN
Nor.; M! :
E X E S S I V E ALTITUDE-OR
NO SMOKING S I G N ON l:EbEPRFHnffEK:E!Rf:!k:s
OFF
0 ESCAPE S L I D E LIGHTS
I
I
Fig. 43 A330 EMERGENCY ,POWERSUPPLY UNITS
; I - ,
I
I ; --. \
' 1 --
The floor path lighting Electro qukinescent (EL) (figure 42) flexible light strips
are installed along the aisles i n t h e carpets and also on the non-textile floor
coverings of the' galleys a n d cross aisle areas.
1 ,
'
/
~hotoluminescentstrips are used on some floor aisle areas for emergency path
lighting (figure 44). These absorb light energy from the normal cabin lighting, or
from daylight, and will emit this back out as light when in the dark - ie when
there is no daylight and other forms of lighting are OFF. These strips will give
out light for about 8 hours under normal operation.
Testing
The BITE test will test the system and the capacity of the batteries. The system
test, which has a limit of 20 seconds to prevent battery pack discharge,
includes:
* Testing the dc and ac supplies.
* Checking for short circuits on each output.
* Checking the voltage output of the battery packs.
* Testing the battery heating devices.
* Checking the EPSU logic and switching circuits.
* Checking system loads.
rnoodull l A-1380
The battery capacity BITE test checks that each EPSU battery h a s sufficient
capacity to run its emergency lights for a t least 10 minutes and does not have a
drop of more t h a n 0.40 AH between two consecutive tests. The test will take u p
to 3 hours to complete.
NON T E X T I L E
FLOOR C O V E R I N G
NON T E X T I L E
FLOOR COVERING
Fig. 44 PHOTOLUMINESCENT
-- LIGHT STRIPS
That concludes this section and this module on aircraft lighting. Try the
following exercises, the answers as usual are in the text. '
Check out the AMM a n d study the wiring circuits from the power supplies to the
lamps. Check the location of the components/lights on the aircraft.
SAQ 1. The oxygen in the air has to be removed somehow. Initially and until
fairly recently this was done by evacuating the bulb. This had limited success
and it is much more common these days to use a gas with no oxygen or possibly
a n inert gas. The gas used will change the colour of the light emitting from the
bulb. Common choices include Argon or a mixture of Argon and Nitrogen. These
two both provide a white/yellow illumination. You may also see Neon used
which provides a more orange illumination.
SAQ 2. Across the incandescent lamp there would be a small resistance. Across
the fluorescent tube there would be a complete open circuit and an infinite
resistance.
SAQ 3 . The first reason is one of choice. Consultations with aircrew and
development over a number of years has meant that the incandescent light
provides a 'more pleasing' illumination than the fluorescent tube. Sounds a bit
like crew pampering, but it is important the flight deck affords them the best
options. Another reason is one of control. To change the illumination of a
fluorescent tube the voltage has to be changed. Usually there is only two
intensities available, dim o r bright. The A N 0 stipulates that flight deck lighting
needs to be controllable to accommodate all flying conditions. Incandescent
lamps offer this facility, a s the luminescence is proportional to the voltage
applied.
SAQ 5. This h a s ideal fault finding possibilities. It is the use of the 'half split'
method of looking a t the last known good place. If one lamp is on and the other
isn't it is highly likely to be the tube. If both lamps are off, both tunes could
have gone, b u t more likely it is the ballast that has broken.
-- ---- -- -- -
All external lights are tungsten \filamenttype, and most are of the halogen fill,
quartz envelope style. This is b d c a u ~ - t h eluminescent intensity is got sufficient
for any &her type of bulb to be uked. (1will introduce during the text one
notable addition to the list of bulbs in use - The Xenon flash tube, more of that
later.) 1 /
i- -
~ ~ Q G . - S e v e r a l - t ' h o u ~ shouldcome
hts to-mind here.
1. We need to be aware of the dangers to ourselves (or others around us). The
voltages concerned are large enough to kill. The unit contains capacitors and
sensible precautions before working on any such system would be to allow
several minutes to elapse to allow any charged capacitors to dissipate the
charge.
2. when the system is tested, care must be exercised as the light is so intense
that it can damage the eyes.
3. Strobe lights can c:ause stroboscopic effects and these can appear to show
rotating machinery a s stationary (propellers and rotors etc). So we need to take
care on and around aircraft. White strobes are to be switched off during night
time activities around aircraft and red strobes should be on for a minimum
time.
4. Due to the heat that is generated during operation we need to ensure that oils
don't remain on the glass surface of the tube. This would cause localised hot
spots and subsequen.t cracking.
CONTENTS
Page
General
High pressure systems
High pressure system - services
Low pressure systems
Air supply
Flow, pressure and temperature control
Enane-ble,ed system - ---I
Preslsure/control - -- \
~ e r n ~ d r a t ucontrol
re I --\
\ \\
~ i s t r i h u j i o nnetwork I , '
Leak detection i ; t
/ /
Other /a& sources I , ,/'
~ervicks, - engine and pylon
/
vacuJm1 systems
~ n s w d r to s SAQs,
I
1
i
,
1
\\\\\\
'\ ,'
I ,'/
i: II
1
/ I
I
GENERAL
Low Pressure (LP) Systems. These are typically medium to high volume, low
pressure systems that are used for engine starting, wing anti-ice, engine anti-ice,
cabin air conditioning, pressurisation and other aircraft systems.
High Pressure (HP) Systems. These tend to be lower volume, but higher pressure
to operate such systems a s flaps, landing gear etc. HP air systems several
disadvantages but are used on some smaller and older aircraft for the operation
of services, and even then their use is diminishing as hydraulic systems have a
better power/weight ratio and are generally easier to maintain.
I
' / 1
* There is an abundant supply of the medium. Air is available (free) all the
ti&e, so we don't need to tarry a rese/rvoir of fluid. I,
/1 L - -
/
<
, I - 1
*
; ,/-' /
L--1
'
,
Pdour freel,/air has no toxins in it - thbugh it often becokes contaminated
yi;h aircraft oils etc and qmells.
/
1 I
1 -
--
7
,
Disadvantages of pneumatic systems:
* Leaks are difficult to trace.
* Not suitable for large components due to the rapid drop in pressure when
selection is made.
- 1-
moodull l A-1384
* A s the systems generally require high volumes of air to move the actuators,
the compressors and the pipework can be large - for low pressure systems
anyway.
Not many aircraft these days have this type of system, although they will be
found in some aircraft.
SAQ 1 Why is the pressure kelief va&e p'laced near the cornpress&?
The air passes through the Presdure Regulator (if this facility is bot fitted directly
to the compre3sor) then to the Oil b d Water drain (sometimes cal!ed an oil and
water t r a p ) ~ O iis
l introduced during-the-lubrication of the compressor and water
is always present in air. Most of the oil and water is removed by the trap.
The air is usually passed through a filter, which may be placed further down
stream and repeated in front of any debris sensitive component. There may also
be fitted a dryer filled with silica gel that removes the remaining moisture from
the air. An anti freeze bottle may also be fitted.
There are a series of check valves (non-return valves) in the system and these
will prevent back feeding of air from one compressor to the other (also loss of
pressure from a bottle should a leak occur up-stream of the bottle).
The air now passes to a number of air storage bottles, again through a series of
check valves. The system shows a primary bottle (though not all systems have
them).
moodull l A-1385
This provides for damping of the compressor output and storage for assistance in
major system operation eg, flaps or landing gear. (Similar to the accumulator in
the hydraulic system).
In the system shows all three bottles are the same and are interchangeable, but
their functions are different.
LEFT HAND
PRESSURE
The brake bottle provides pressure to the wheel brakes, which cannot be used by
other systems due to the presence of the check valve. In an emergency, should
system pressure be lost then the brake pressure is available from this dedicated
bottle.
rnoodull l A-1386
SAQ 3 Given the high pressures, what are the likely sizes of the pipelines
a n d what materials are they made from?
Compressors
These are either single piston (two stage compression), or double piston (four
stage compression) operated.
They are usually engine driven though some may be electrically powered. The
two stage compressors produce pressures u p to about 600psi whilst the four
stage compressors will give pressures u p to 350Opsi. -
--
I
They are iubricated with oil from the engine oil system. Any t i l u r e indication is
sent to tkde flight deck. I
1
I
The single cylinder double compression compressor first com$resses the air in
t h e t o p ,side of the cylinder, then: compresses it in the bottom side (the lower part
of the cylinder and piston a r r k g k m e n t being a smaller swept volume).'
, I
The four 'stage compressor has1two pistons with each compression sequence
similar t o the above - so the air is compressed four times.
-
Because the compression is adiabatic the air gets hot so cooling fins are fitted to
the compressors to help in heat dissipation.
The purpose of this valve is to relieve the pressure should failure occur in the
compressor control or Pressure Regulator Valve for whatever reason. Its
operation is simple (usually using a ball and spring). Figure 2 shows a pressure
relief valve.
The valve is held down on its seat by the spring. Pressure in the system tries to
de-seat the valve. Under normal pressure the spring is strong enough to hold the
valve on its seat. If the system pressure approaches the preset level (over-
pressure) this overcomes the spring force and the valve is de-seated, allowing
system pressure to be ported to atmosphere.
The spring force can be adjusted and in doing so the pressure a t which the valve
de-seats can be altered within a certain range - any adjustment of which must
be carried out in a properly equipped maintenance bay.
ADJUSTER SCREW
$ ,
1
,
HIGH P ~ E S S ~ R E A l R
:
\
1
\ \
' I
1 I
f i , Fig.
/
/
PI-essureRegulating Valve
This may be fitted close to the compressor or actually on the air bottle itself (if a
single bottle system). The whole idea is to off-load the compressor when normal
system pressure is reached. It works similar to an Automatic Cut-out Valve in a
hydraulic system.
When system pressure falls to a preset value the outlet valve spring pushes the
outlet valve closed and compressor air then goes through the check valve and
normal charging continues.
PORT TO
OUTLET OVERBOARD
VALVE
CHECK VALVE
AIR FROM
COMPRESSOR I
___)
- - -
-- I
,
Oil and Water Trap --- \ II -
/
I
I \
Figure 4 shows a simple Oil and Water rap. >Theair comes i'n a t the side and is
caused to impinge'on the baffle plate. The heavier droplets of water and oil stick
to the plate and run down to collect at the bottom of the trap. The cleaner air is
directed out of the top of the unit into the, system. The trap has to be drained
periodically as laid down in the maintenance schedule.
AIR IMPINGES ON
HALF TUBE BAFFLE
~uzTip; .
COARSE STRAINER
w
Fig. 4 OIL & WATER TRAP
DRAIN
Not all of the airborne debris is removed by the trap so the 'clean' air is passed
through a filter (and sometimes also a dehydrator) to remove the remaining
particles of water and oil. These extra items require periodic cleaning/ changing/
emptying.
Normally made from steel, with some wire wound on the outside, and then
sealed, before being painted (usually grey). This identifies it a s an air bottle and
it will also have a tag with the date of manufacture, safe working pressure and
the date of the last hydrostatic test stamped on. Usually installed in the upright
position with the connection at the bottom. They sometimes have a stackpipe
standing up within the neck of the bottle preventing moisture from entering the
system that has collected in the bottle.
,/' ,,'
I
1 I
I
I - - - \
I ' _
Fitted doivn stream of the Oil & Water ~ ; and a ~any dehydratqrs aridfilled with
antifreeze (ethylene glycol or similar - but kheck the AMM). Thfs is picked up by
the air as/it pas?& through the bottle. It pt'events any rnoisthre that might be in
the air /from freeqing. It require+ fhe rnaidtghance task of tbpbing up the anti-
/' 1 ,
freeze-at kgular intervals. 7 i - -
I
/
1
I
With reference to figure 5. It can be seen that there is a spring and bellows
mechanism. The spring balances the air pressure above it. The spring has an
adjuster screw and this i s used to set the operating pressure of the valve.
When air supply commences the valve is below its operating value; the spring is
fully up and all the HP air passes through to the air out port. A s the pressure
rises to just above the operating value the HP air on top of the bellows starts to
compress the spring; this in turn moves the valve inlet plunger to the left, via the
bell crank level. A s this happens the inlet to the valve is choked and the pressure
felt at the outlet is reduced.
rnoodull l A-1390
VALVE INLEX' PLUNCgR
LP A I R OUT
m AIR IN
BFTL (IRAN)(
FIXED PrVOT
COHPRESSION
ADJUSTER SCREx
r ----
-
When air outlet pressure reaches maximum the valve shuts completely.
I 1
1 1
In real time, provided the maximum outlet pressure is not reached, the valve is
constantly moving in and out to keep the lower outlet pressure korrect.
I
- --
Check Valve ,
i
These may be designed with a ball and spring; a half ball and spring; a plate and
spring, or a flapper valve and spring. Figure 6 illustrates a flapper
-
valve type and
a ball-and spring type.
SPRING
-
__t
\
ARROW (marked on body
la show now d8recbon)
%ALL SPplNG
\
ARROW (mark& on body
I0 shwr flowdlrecboo)
rnoodull l A-1391
The spring is reasonably weak and a s such requires little effort to overcome its
force providing the air is moving in the free-flow direction (in the same direction
a s the arrow shown on the outer casing of the valve). If the airflow is reversed,
the spring will close the valve assisted by the reverse air-flow.
Pressure Indication
A bourdon tube type pressure gauge is fitted in the system for maintenance
purposes where-ever there is a need to monitor the pressure. If pressure
readings are required in the flight-deck then a pressure transducer is fitted in
the appropriate part of the system and a dc of ac supply is sent to a moving coil
or ratiometer type instrument.
Figure 1 does not show these transducer positions but they will be fitted where-
ever the designer feels there is a requirement, and they could be fitted at the
i pressure
, gauge positions anv-ay.- , ,
~ i r c r d Services
t
I 1 I
The adr sllpplies will be fed to aiicraft
- services (eg, landing/&r, flaps - trailing
_-A
I
edge &d leading edge, windscreen_wipers etc) via selector valves. These are
similar in principle to the manLally o&$ed valves fitted to hydraulic systems,
the main difference is that the2e ,;Ke no return lines from thelvdves - returning
air bein2 ported,tA outside the yalpe. Pipeline connections toeach valve are:
1 - presTure, 2 - to one side of the actuattr (jack), 3 - to the other side of the
actuator.-If the actuator is returnkd by-the action of a spcng then there are only
two pipeline-connections to the-selector-vave - pressure and exhaust.
* Brake systems.
* Flap systems.
* Gear retraction systems.
Aircraft with HP pneumatic systems tend to be older and often use a cabin
blower for air conditioning.
Let's first of all take a look at actuators (sometimes called jacks). These fall into
one of two main types, single or double acting.
SAQ 6 Consider why they are called this and, therefore, briefly explain the
difference.
- 9 -
rnoodull l A-1392
Single Acting Actuator
Figure 7 shows a single acting actuator. Pneumatic pressure is applied from the
selector valve to one side of the piston. This overcomes the spring pressure and
moves the actuator (in this case in the extend direction). Removing the
pneumatic pressure via the selector valve allows the spring to return the actuator
to the retracted position.
- -
- -
Carbon impregnated rubber seals are used to prevent leaks aro;und the ram and
piston. Single acting pistons are limited in their applicationlbut are used in
brake systems and sometime in gear retraction systems. i I
I -- i
L
- - - -
\ PISTON ROD
/
PISTON HEAD
/ ,CYLINDER HEAD
The selector valve is shown in figure 10. Mechanical up and down locks will be
fitted (but not shown in the drawing).
M F L A P S 3 EXHAUST
A n 'up' selection is received from the landing gear select lever in the flight deck.
This sends a 28vdc signal to the selector valve (via the closed contacts of the
uplock sequence switch). This supply energises the up solenoid (as shown). This
in turn moves the pilot valve and allows compressed air through to the right
hand chamber, which moves the control piston down, and through mechanical
linkage moves the left control piston up.
The right hand chamber allows the compressed air through to the u p line and
this acts on the 'up' side of the main actuator. Also at the same time the left
chamber has allowed the 'down' side of the main actuator to port to atmosphere.
- 11 -
rnoodull l A-1394
CDKPRESSED AIR SUPPLY
--
The gear moves, and is locked in \he u p position by other rnkans-(spring loaded
plunger lock for example). As this, happens, the sequence s+tch on the uplock
actuator will open, removing the 28vdc from the selector solehoid. The pilot valve
now returns under spring pressure and through differential {orces on the piston
surfaces the control pistons return to neutral.
- -
If the solenoids were "removed" and control cables or push/pull rods connected
instead direct to the linkage, then the valve would be mechanically selected.
Braking System
* Hand operated.
* Pedal operated.
Pedal Operated Systems. Figure 11 shows the location of t h e 'foot motors' and
figure 12 show a cut-away of a typical foot motor.
'Tipping' the toe pedals forward operates the system. This has the effect of
moving down the brake control valves. As this happens the valve sleeve moves
into the motor body and closes off the exhaust valve. Pressing the pedals further
down allows the valve sleeve to push the valve stem up and starts to un-seat the
valve head. This allows some pressure through to the brakes. Pressing still
harder opens the valve head still further and increases the pressure to the
brakes. This provides for 'progressive braking'.
The harder the push on the toes the harder the brakes go on - exactly the same
as in a vehicle.
-
-
- 1
, ir J BRAKE CONTROL VALYES -
(FOOT MOTORS)
' I I
I
I
I
I ! RUDDER PEDAL
I 1
I
I ' TORQUE TUBES /
1 I - ,
1
l i
I I I /
' 1 I
I \I
I 1 I
/ r i
I /
i -1 Fig. 11 BAK
iE
-
--
PEDAL'FOOT MOTORS
/ -
1- - - - - 2 - - I
ATTACHED TO
AIRCRAFT STRUCTURE
IXLm VALVE
AIRIHLET VALVE STm
BRAWS
SPRING
If the pilot applies rudder in one direction a t the same time as pulling the brake
lever the DRV will apply air pressure to one main landing gear whilst pressure to
the other side is reduced. This produces differential braking a n d allows t h e
aircraft to be steered (on many older aircraft this is the only way to steer t h e
aircraft).
Both systems have the ability through pawls and valves to hold the brakes on -
parking brake. So much for the pilot's side of things, what happens down a t t h e
business end?
- - -- -
I
BVAKE 8 - OR LINING RrVBT BRAKE ,
e x ~ m r or
l n ~ CLIP 1
-- -
operates the switch is made apqlyingg e& 'h to the warning light-via a 'hold on
re-lay' (figure 14). The hold-on 1 relay keeps;the warning illuminated until
t h e pilot u n l a t c h ~ sthe relay. I I I
/
/ i I
1
I
I
I
1 I 1 I
I
/
I
/ - '
VALVE SPINDLE
L-
vL
fj r
LATCHING
RELAY
dc BUS
I: EARTH 2
-MICRO
P EARTH 2
SWITCH
PUSH TO
RESET
SAQ 8 What colour do you think the warning light would be on the flight
deck and where should it be placed?
SAQ 9 Why is does the switch 'earth' the lamps / warning light and not
operate the supply? (It is normal practice to close a circuit by using a
micro-switch to provide a n earth to a. normally live bulb).
Exercises
1 1
4. Explain the operation of the components on the HP system.
5. Look in your AMM a t chapter ATTA 36, and study the systems just
- described. This may not be possible if you are not-working on older
aircraft, b u t have a look anyway.
High volume^ low pressure (hot) air is supplied normally through large diameter
ducting, and this pneumatic supply can be used to deliver air to any of the
following systems (in some cases suitable cooled):
* Wing, fin, tailplane, slat and windscreen anti ice (see the book in this
series on Anti Icing).
* Cargo compartment heating.
* Engine Anti Ice (EAI).
* Air conditioning packs (air cycle systems) for cabin air conditioning.
* Air driven hydraulic pumps (auxiliary pumps).
* Hydraulic reservoir pressurisation .
* Engine starting.
* Thrust reverser(s).
* Potable water (drinking water) pressurisation.
*1 Smoke detector aspiration. - -- . - -
- - -,
*I ,prpde heating and aspiration.
* 'Sdme systems operatioq (the ? 4 ~ uses it for LE flap
deployment for
k&nple but this is not common). I I
I I 1 1
I I I
I
I I -
/
/'
/
/
I
1
AIR SUPPLY .
I -- I
I r - - '
The a& can come from a numb& of source's and these include:
1 I
17 I 1 II
I 1
J;
Using the exhaust gases from a turbo prop engine.
* A tapping (engine bleed) from the compressor side of a jet engine.
* The APU (Auxiliary Power Unit).
* External connections from ground carts etc.
1
The air has been compressed adiabatically and is hot. It is ideal for anti-icing but
has to be cooled for such purposes as cabin conditioning and pressurisation.
Figure 15 shows a schematic of the pneumatic system as fitted to the early B747
and figure 16 shows the general arrangement of the system a s fitted to the A320.
Study these drawings carefully and note the ways the various supplies are
connected, note also the services that use the air supplied.
Originally designed for the piston engined aircraft where engine driven
compressors where fitted for the supply of air.
rnoodull l A-1400
',*
- --- -
1
\
,
Fig. 15 B747-,100 PNEUMATIC SYSTEM
I
1
!
To wing anti-
fh To air conditioning packs
ventilation
Wing anti-ice
valves
This sort of system is limited to older pure jet aircraft - the B707 for example.
SAQ 10 When is the lack of air likely to occur? And when would the crew run
the turbo compressor?
Not too unlike, in principle at least, the HP systems described a t the begmning of
the book. The compressor is driven by the engine and supplies air to all services
such as de-icing, cabin conditioning, pressurization etc.
The compressor (on the VClO at least) is a screw type with two intermeshing
(large) screw threads driven from the auxiliary gear box of the jet engine. It is
fitted with a slide valve which automatically regulates the air output.
Two compressors feed the air to services such as pressurisation etc.
Not common but used with some turbo-prop engines. Some of the jet efflux is
ducted away from the jet pipe to a heat exchanger. Here it exchanges its heat to
clean ram air before being ducted back into the jet pipe. The hot ram air is used
for de-icing/ anti-icing/ heating purposes.
HOT RAM
,RIA
TO SYSTEMS zh
JET EFFLUX
v
I
I
JET PIPE
I
I I I
- - . - --
SAQ 11 Why is the jet efflux system sometimes fitted to turbo-prop engines
and never to pure jet engines and why is the air put through a heat
exchanger and not used 'as is'?
The most popular system on most commercial aircraft is to use air taken from
the compressor of the jet engine.
This consists of a tapping (or tappings) from a stage (or stages) of the compressor
of the jet engine. When more than one tapping is used it is usual to have a low
pressure tapping and a high pressure tapping with modulation provided for the
high pressure tapping.
The tappings provide an abundance of clean air - provided the air entering the
engine is clean in the first place and there are no engine malfunctions such as
front bearing oil leaks. The air is hot - about 150°C - but check the actual
'aircraft manual.
At low engine power settings air is taken from all the tappings with non-return
valves in the system to prevent the air entering the LP side.
A s engine power is increased, enough air can be provided from the LP side and at
a pre-determined pressure the HP valve shuts-off automatically. This air coming
from the engine is called Charge Air and is at about 50 to 60psi pressure - but
again check the manual of the actual engine.
(-
\ - 1
- - - --
Charge +r normally needs coolingand,?his is usually carried o u t using surface
heat e qhangers (similar to radiators in a road vehicle) and iusing ram air as the
P medium. To assist this1 skstem Cycle systems a r e used such a s the
cooling A?
~oot system. I I I
1 ' I
I / ,
1 _ - _ A '
In some aircraft a Vapour Cycle Cooling System (refrigerant s$stem)'is used., but
this system is not common. ( ~ dmor&inf&mation
r on cooling of charge air refer
\ \
to the book in this series entitdd b b i n Cnnditinninrr 2nd pr&ssurisatinn.l
, HP s m OFF VAL,?
----
SPARTW
V3U.n
I
KFAT EXCHANGER
NRV
BYPASS VALVE
ENGINE BLEW
OVERHEAT VALVE
PROTEITION
rnoodull lA-1404
Ozone Converter
Fitted to some aircraft in the supply ducting from the jet engine - on the BAe 146
for example, (those fitted with this option), It is between the engine tapping and
the isolation/pressure reducing valve. It removes contarninants/odours from the
air supply by a reaction process between the metal plates and the hot air.
The converter consists of special metal plates fitt.ed within a metal container
covered in a fire proof material and connected into the ducting using "V" clamps.
CATALYTIC
I
/
I
-
--
I
I
I
I '
I
I
The charge air must be a t the correct flow rate to meet the demands of the user
systems and must be at the correct pressure and temperature.
Because of the adiabatic compression of the air it is always hot so the biggest
problem is that the air may get too hot. In this case cooling is provided usually in
the form of surface heat exchangers using ram air. The exchangers are placed in
the airflow and often placed within the engine fan airflow on fan engines.
---m TO SYSTEM
N.R.V.
FLOW CONTROL VALVE
For air that comes from an engine driven compressor or cabin blower then, if the
flow rate is too high (at high engine rpm), the excess air is dumped over-board
(figure 2 1).If the air comes from a tapping on the compressor casing of the jet
engine then a restrictive type valve system is used (figure 22).
PRESSURE
NON-RETURN REDUCING
VALVE VALVE
_I)
1 C__C
ENGINE SHUT-OFF
VALM
FLOW COHTROL TO SYSTEM
COMPRESSOR
STAGE
- r
ENGINE BLEED SYSTEM
, - -7
- -
1 I \
I \ \
l 1
1
SAQ 12 1 Why is the excess &r !dumped over-board when it Comes from an
I 1 engine driven corndressor and y h y is it simply restricted when it
) comes from the en&&? -,
/
/ I II
driven-compress'or/ blower. - -
L ,
'
-i - -
With reference to figures 21 and 23. The charge air flows through a venturi
within the duct where density and velocity are monitored. The static connection
(pressure) supply is fed to one side of a diaphragm whilst the venturi connection
(suction) is supplied to the other.
The diaphragm will move in response to these pressures and move contact Y to
close onto Z or X depending on direction of movement of Y. This will send a
signal, via the phase reversing contactor, to either close or open the spill valve
butterfly.
The amount of air bled from the engine will depend on the demand from the
services. The amount of air coming from the engine will depend mostly on engine
rpm. At high rpm there is usually too much air being delivered so air that is not
required is stopped from leaving the engine by a restrictive type valve system.
SPRING INLET
OUTL
'ALE
moodull lA-I407
On the simplest system this is achieved using a Variable Orifice Valve
(figure 24).
The air enters the valve and leaves via the orifice plate. When flow rates are
high the pressure acts on the piston which is caused to move to the left
against a spring. This closes the acorn valve a little, restricting the air
leaving the unit
I
* Engine
- -
air supply. 7--- -
control and indication. -- \
* 1 Qistribution network.
1 1 i \
, r'- - I
The HP Valve
Pneumatic Control
With reference to figure 25. The system is made u p of two parts, the High
Stage Valve itself and the Valve Controller.
At idle power we would expect this valve to be open but initially it is closed
by spring action. High stage air is felt in chamber A and this keeps the
valve closed. Opposite the chamber A orifice there is another off-take going
initially to a test port and then onto the controller. The Shuttle Valve
moves over and the air pressure is allowed to the switcher solenoid (this is
energised to close the valve so is normally de-energised as shown).
- 25 -
rnoodull 1A-1408
",r.i+5,uS
m.tl@ ,,I s u b 7
I _ - - -
I
OY€t.lO~
L_------- _I- II - / ,
! I
I i l
Air passes through the Over Pressure Control and (for now) through the
Low Pressure Control, it now h a s a free run to chamber B of the High
Stage ~ a v e d i a p h r a g m Differentidpareas
. now force the vdve to open and
allow 15thstage (HP) air into the pneumatic system.
Initially a s the pressure is fairly low this is fully open, a s the air felt on top
of the diaphragm is not sufficient to move it against the spring. As the
engine speed increases and the HP pressure increases the pressure on top
of this diaphragm and it starts to exert a downward force on the control
aperture. This starts to close and in doing so reduces the air getting to
chamber B of the HP valve, causing that to start to close.
Further increase in flow and pressure closes the aperture still further and
eventually the HP valve is completely closed. This actually happens when
the HP bleed pressure is about 120psi.
There are other items in figure 2 5 that we shall return to when we consider
indication and protection. But for now lets move on.
- 26 -
rnoodull l A-1409
Electrical/Electronic Control
, 1- /' / 1 1
, ,' 1
' / I
AIR
I I+/ ) AMBIENT V E N l
SUPPLY A I R
( F R O M HP A I R SOURCE)
- 27 -
rnoodull lA-1410
The valve (as before) is sprung loaded closed and bleed air keeps it shut.
15thstage air enters the controller where it passes through two regulators,
these bring the pressure down to 55-65psi. An electronic unit measures
the pressure down stream from the high stage valve. This will initially be
very low/zero. The unit sends a n electrical signal to the torque motor to
move in the direction to cover the vent. This allows the full 65psi down to
chamber B on the valve to open it.
A s the engine speed rises the pressure downstream will rise. The electronic
unit senses this and sends a signal to the torque motor to open the vent
and start to cover the inlet. This reduces the pressure to chamber B and
starts to close the valve.
1
-
I -
PRESSURE CONTROL
Another valve is added to the system, not too dissimilar from the HP valve,
down stream and this is used for pressure control. Referring back to figure
19, look for the Engine Bleed Valve. (You may know this valve by a
different name on your aircraft, such a s Pressure Control Valve etc.)
This engine bleed valve will typically have the following functions:
* Pressure control of the pneumatic system.
* Non Return Valve, preventing a stronger engine from cross bleeding
to a weaker one.
* Shut off valve - through flight deck switch action.
* Reverse flow to allow cross bleed engine starting.
* Temperature control (backup mode).
- 28 -
rnoodull lAp1411
Pressure Control Mode
The valve behaves i n a similar fashion to the HP valve and functions in the
same way. Sprung loaded closed and pneumatically opened, it can be
controlled pneumatically or electrically. It is usually controlled to a slightly
higher pressure than the HP valve. It is this valve that sets the pressure in
the p-neumatic manifold and ducting, which is typically about 55psi.
This closes the valve when the pressure sensed by the downstream port is
higher t h a n the upstream port. This is done by the servo unit in the
controller and vents the sense line to atmosphere, allowing the spring to
close the valve.
'..
Shut-off Mode -
- 1
- I
L
(-
If the flight crew are unhappy w i t h t h e engine or the airflo,wTthe air to or
'I
from it can be stopped by enkrgising a so,lenoid. It allows the sense ,line to
vent t q close the valve. In addition to the switch action ofi the flight crew
this bolenoid will also be ener'gised if tlie~firehandle is pulleld.
I
\
~evekskFlow Mode
1 '
I
I / I i I '
If the 4ngine i s 'not started it kslnot pro,dubing any air. A s the start valve is
d o w n s t r e a d of the engine bleed--~alv<(oh start selection), d u e to the non
1-
r e t u r n m o d e the air will ndt-be able-to reach the starter71n this case the
engine bleed valve is put into reverse flow mode and forced open. On some
bleed valves this function is removed as designers fit the start valve
off-take downstream of the engine bleed valve.
I,P systems can suffer from over pressure which is normally the result of
the HP valve remaining locked open at high engine speed. Simple spring
loaded flap operated pressure relief valves are fitted in the system to
prevent over-pressure.
- 29 -
rnoodull lA-1412
TEMPERATURE CONTROL
We have already touched on a back-up method but lets now look a t the
primary method of temperature control. Figure 28 shows a typical method
of cooling the air.
This shows charge air being cooled in a precooler cooled by fan air (ram air
from the fan of the engine). The amount of fan air allowed through the
precooler is controlled (modulated) by a modulating valve taking its signals
from the fan air temperature sensor.
--
FAN A I R
/
OUTLET --
4 \
I I
BLEED AIR I I I BLEED AIR
DUCT (FROM - DUCT (TO
ENGINE) I PRESSURE AIRPLANE)
-
I
-+
-
BLEED A I R
PRECOOLER ---------- 1 ' REGULATING
AHD SHUTOFF V A L V E
l 1 -+
(PRSOV)
\ ', I I
FAN AIR; I-
TEHPERATURE
I
I
-
SENSOR/
FAN A I R PNEUMATIC SENSE TUBE
MODULATING
VALVE
FAN AIR -
INLET
Fig. 28 CHARGE AIR COOLING
The last method is the most common, but the first two are still in use on
older and lighter aircraft.
- 30 -
rnoodull l A-1413
Bimetallic Control
0 1 - H F T A L L I C TEXPERATURE
,SMSING SPRING
.ow FROM
EXCHANGER
MODULATING
I I -- '
, /
1
I
Fig. 29 BI-METALLIC FAN AIR
' I
I ~
\
\' \
\
/? I I
pneumatic Control I
I I i / 1 1
1 1 I
i
j
(-1 1 I
This achieved by placing a probe in-the airflow from thepneumatic system
I - --
(figure 3 0).
-- - -
As the temperature of the air rises, the sleeve of the probe expands quicker
than the inside and de-seats the ball. This allows pneumatic pressure in
the sense line to the temperature control valve to bleed off. It is a sprung
loaded open, pneumatically closed valve, and a s such will open more. This
has the effect of allowing more cooling air across the pre-cooler.
NOTE. This type of probe h a s also been used connected direct to the HP
valve, operating on the same principle but closing the valve this time. This
is because it is usually the HP air that requires cooling only as the IP (low
pressure air (even a t its hottest) is still below the over temperature value of
.the pneumatic system.
BLEED M ATMOSPHERE
/
'
-
BW AND
SEAT
HIGH EXPANSION
HATEXIAT..
-
LOW EXPANSION
KATERIAL
Electrical Control - /
I I - - , I --
Figure 25 is actually the Boeing 777 system, and figure 31 shows the
Airbus A 3 1 9 system so that we can consider both temperature control
systems together. They are similar to each other and similar to other
aircraft, the only real differences being the termi~ologyand component
details. - - - -
Study figure 31 and follow the air supply from each engine, the APU and
the ground supply to the various services:
* Air conditioning packs 1 and 2.
* Hydraulic reservoir pressurisation.
* Drinking water tanks pressurisation.
The temperature sensor sends the signal of the value to the ASC. The ASC
then sends a signal to the Fan Air Valve to either open or close depending
on whether the system is too hot or too cold. The Fan Air Valve h a s a
rotary variable displacement transformer (more of that later) to provide
feedback to the ASC of its position. This is a closed loop negative feedback
control system.
rnoodull lA-1415
-
I _- \ I
1 -
I Fig. 3 1 SYSTEM
1
CONTROL - A 3 19 ,-
/
\
i
1 1
/
I r\ I
1
i
I
I
'
NOW :tol o o k j ~ some
t of the c o ~ ~ o n e n t s ~ , I
, i
ri - - - ,
/
- I - /
I
-
2
I
The Temperature Sensor. Refer to-fig-~ire32. If a conductor is heated its
resistance value changes - for most materials the hotter the material the
greater the resistance (some have a negative coefficient of resistance and
the hotter they get the lower the resistance).
It forms one leg of a Wheatstone bridge, the output of which is sent to the
ASC for processing.
The Fan Air Valve. It is sprung loaded to fail open. This ensures that the
maximum cooling effect is available. (Incidentally, as far as "Fail Safe" is
concerned, the problem of what position a valve should fail in is one of
common sense. Think about what is least desirable if a component can fail
in one of two modes and in the event of failure the valve should go the
opposite way.) The valve has a manual position indicator so that the
engineer can see the exact position if necessary.
Also it will have some form of feedback pick off. This may be a digital pick-
off, or a potentiometer, or a variable displacement transformer. A s a guide,
Airbus tynd to use the former whilst Boeing tend to use the latter.
Whatever is fitted the principle is-the s&e. -
I
\
I
l 1
The Air8Supply Controller. The ASC will take signals from various systems
and the, pneumatic sensors for processing. This informatioh can be:
I /
* Analogue, voltages are either ac or, dc from a variable displacement
transformer, or a potentiometer (vadable resister). 1
' -
From this information the unit calculates how far each of the valves h a s to
open. It then sends the signal to the valve and monitors for a response. It
takes into consideration how much air is required by the aircraft. (No point
bleeding air off the engine if you don't need to.) For example as the pilot
switches on an air conditioning pack, a BCD word is sent from the pack
controller to the ASC, the ASC opens the engine bleed valve more to
compensate for the loss.
Modern aircraft are automated and there are many signals moving from
unit to unit. This can make fault finding difficult and we need to take
notice of all the fault codes. You will learn more of this in the LBP book
covering JAR module 11.18.
There are often two (or more) ASC7sto allow for a degree of redundancy.
- 34 -
rnoodull lA-1417
Over Temperature Control
The temperature sensor sends a signal either to the shut-off solenoid (via a
relay) in the pneumatically controlled system or to the ASC in the digital
system. This has the effect of closing the engine bleed valve and hence
stopping the pneumatic bleed. The aircrew (or ASC) will now open isolation
valves to allow cross bleeding from the good enginejs).
the
I
APU
- 35 -
moodull lA-I418
Study the system noting all the components and their location. The system
comprises:
Ducting
The ducting used is usually titanium or stainless steel. Stainless steel has
a slightly higher tolerance to temperature changes and a better coefficient
of expansion; as such it is used nearer the engines. Often, by the time the
a i r reaches the engine bleed valve is sufficiently 'cool' t o use the lighter
titanium ducting. . , \
The ducting is supported throughout its length with clamps and stays
the aircraft structure. An example is shown in figure 34.
It is important that the supports are not over stressed and that the ducting
is aligned correctly. Care needs to be taken to ensure that the tie rods are
adjusted properly. Shims may be used to provide for better alignment.
When the ducting is in use it gets hot. Even the 'cooled' air leaving the pre-
cooler will be in the region of 120-150°C. The ducting needs to be able to
expand without buckling, and still be leak proof a t the start of operations
(cold) and when it is hot. To achieve this, flexible joints are used and there
are several types available. Figures 35 and 36 show two examples.
rnoodull lA-1419
&
(IROSS SECTION OF
ASSKIBLED WCT
DUCT
EXPANS I O N
GAP
- 37 -
rnoodull l A-1420
MEASDRED GAP
m SWAGED
SEAZ, DUCTS
\
I -
I
1 I
These types of joints tend to leak around the seals in t h e flange. When
putting any pneumatic duct together a small addition of silicone grease
assists i n the assembly and doebn2 add dlanger to the sydtekn - but check
your AMM as to any lubricants used. -
~
- -
I
SAQ 16 What rnaintenanck activitiesi might be requirc!d o n pneumatic
, ducting and what precautions should be carried out?
I
-
--
Duct Maintenance
rnoodull lA-1421
Leak Detection
Leak detection falls into two categories - checks carried out after
installation a n d checks carried during service due to duct and joint
failures.
After any installation is carried out the system is pressurised and checked
for leaks. This is normally carried out using a ground cart, but even so,
any leaking air will be hot. The following is a general procedure (always
check your AMM):
I
I
I
I
~eaJsbthat develop in flight Fan damage1local structure; babies land any
/
equi$ment that is near. If yo$ consider,,the normal operating terriperature
.- -
rangk of a pneumatic systerh 1s cl&e..to the ternperaturk for,/annealing
r-- -,
aludidium alloy and above the temperature for precipikation--tr&atment,
\
darn&e can soojn occur to the 4tructure if\subjected to the leaking air for a
perid,d bf time.1qeaks need to be detected quickly and isolated/repaired.
,/ I
1
I I
/
Some &rcraft have a 'firewire' style-of l e k detection systdm that detects
anyoverh-eat situations. '- - - - , - - - -
The firewire is r u n the length of the ducting and is usually split into
sections so that the system can work out exactly where the hot air leak is.
Firewire is covered in detail in the LBP book on Fire Detection Systems but
is general they may be of the Resistive Type; the Capacitive Type; or the
Systron Donner type. In all cases a local overheat is detected and a signal
sent to the flight deck.
On older aircraft this would illuminate a warning on the flight deck and
the crew would take the appropriate action. O n more modern aircraft the
signal is fed to a card file or processing unit (computer). This registers the
fault and sends signals in BCD form to the Air Supply Controller. The ASC
will automatically close off the section of the duct that is leaking by using
the isolation valve(s) and/or the engine bleed valves.
Unit detectors or thermal switches can dlso be used for leak detection.
A s the switch heats u p contacts come together and this will put the
indication light on t h e flight deck. As with the fire wire system the switch
can equally signal a computer to operate a n automatic process. (Again
described more fully in the book Fire Detection Systems).
Isolation Valves
WING
ISOLATION VALVES
SHAFT
I POSITION
I
I INDI CATOI.
WING ISOLATION VALVE' (TYP)
- 0
- -
Figure 40 shows the flight deck control panel associated with figure 39.
Study both figures so that you get a good overall picture of how the system
works.
In digitally controlled systems an OFF selection will turn the unit off, but
a n ON selection will put the unit under the command of a computer. Some
manufacturers have renamed them to 'request' switches rather than the
traditional on/off switches.
I
I
I
I
1
I I I
I
1 1 '-
I I I
I
VIIC I 1
II
I I
I
V1LV1 I I
I I
.
I I
U
I I
I
V
. . - -.
I I
! -- -
DUCT PRESSURE
INDICATOR
Has two pointers
marked L and R
indicating left
and right hand
ducts.
- - - - - - - - - - - - - , - - - - I
FLIGHT ENGINEER'S PANEL
Figure 42 shows an early system for measuring mass flow. The transducer
consists of a small turbine arrangement placed in the duct that is free to
rotate.
I I -
r-- I '
\ '
,\
,
\,
PS CIRCUIT BREAKER -- AC '1
PANEL
! I
1 ,
j ,'
, .
PACK 2 ,,
PACK NO 3
AIRFLOW SENSmA
I
PACK NlU 3
AIRFLOW S E N 3 0 A
R E S I S T I V E TEMPERATURE DETECTOR
--- --
So far this book h a s covered air coming from the engine$ only, but other
I
sources are used and figure 33 shows 2 of them. I
The Auxiliary Power Unit (APU) is usually located a t the back of the aircraft
in the tail cone section. It h a s two functions, these are to provide 400Hz
30 2001 115vac to the electrical systems and pneumatic pressure to the
manifold.
A check valve is installed so that when the APU is not running air from the
pneumatic manifold cannot back feed through the APU.
Also there is a bleed control valve and some form of dump valve. These two
work in opposition to each other. When one is open the other is closed. The
bleed control valve is similar to the engine bleed valve but in this case it is
a simple shut-off valve (it doesn't regulate the pressure like the engine
bleed valve did).
VERTICAL
SUPPORT TUBE
FUEL
D R A I N S LINE,
I -
'
- -
I
AND VENTS
- -,
r \
\ '-
' I
1I ~ i 44
I
~ APU'~DETAILS
l I
I I
I I
I I '-- '
//
/
/: I
Air p'rebsure from the APU is contro!l6d,by altering the 1hlkt Guide Vanes
to the toad compressor. orei ion
this i"n the Jet Engine bdoks in this series
entitled APU.
I
1-1 I I
~
1
\
I I
I I 1 ; I
An APU cannot stop produdirig air when it is running, even when the
J
syst&n doesn't require it. The dump-ddve or surge bleed~valveopens when
the~151eFdpTdiGis closed to cillow-th-isqexcess air' to bleed (spill) overboard.
Figure 44 shows a typical APU installation; note the position of the
pneumatic components.
Ground Rig
The rig is connected to the system after checking the AMM and making
sure the aircraft is configured for the test. The engine is started on the rig
and pressures and flow rates adjusted to the figures given on the
panel/AMM.
Great care needs to be taken when connecting pneumatic hoses to these
points, a s they can break under the sudden loading. This can leave large
volumes of high temperature air exiting the broken nozzle. Prior to
applying pneumatic pressure you must carry out safety checks on these
hoses as well as flight deck safety checks.
SERVICES
Various services are provided from the pneumatic supply including cabin
conditioning, anti-icing etc. These are covered in other books in this series
so here we will look at engine start and various components around the
engine and pylon.
\ \
LOW STAGE
CHECK VALVE
u
START OPEN LIGHT
VALVE PRESSURE
SWITCH
\ / START
TOR
The start valve will open if the solenoid is energised and air pressure is
available. The solenoid is energised if Engine Ignition Switch is at GND
START.
The Pressure Switch illuminates the START VALVE OPEN LIGHT in the
flight deck if there is pressure down stream of the start valve.
Pylon Valve
Situated within the pylon and is electrically operated but can be manually
operated for maintenance purposes.
It acts as a check valve preventing air from the ducting going to the engine
from another engine.
Warning lights come on - when valve closes.
- when duct temperature exceeds 255°C.
The reverse flow solenoid is energised to cancel the check valve function
and so allow air from the duct to engine start if engine ignition switch is at
GND START.
Figure 47- shows the pneumatic system for engine and pylon.-Take time to
study the drawing and make syre you can understand how-the system
8
works.
.
~ I ) \
ISOLATION VALVE-
1
1 '
I
- - -
\ FROM APU O R ,
GROUND CARTS
,
1 :
I
I PNEUMATIC
MANlFOL D
L- r
HYDRAULIC TANK
PYLON V A L V E
TEMPERATURE STRUT
w
Fig. 47 ENGINE & PYLON SCHEMATIC
- 48 -
rnoodull lA-1431
That concludes this section on low pressure pneumatic supplies. Now have
a go at the following exercises. The answers, a s usual, are in the text.
1. Look again a t the basic engine bleed schematic diagram (figure 24).
Explain where we get air from and a t what times certain valves close.
5. What type of valve is the High Stage (HP) valve? How is it operated?
i 7. If there
I is an over-temperature,
- - .
what is the most likely
-- cause? -
- I
- -'\
\ /' -- -
9. Gist the various types of duct c1,aknd and explain how they &e sealed.
I -- - / /
/
10.
-
w h a t is the correct p+cedse, fpr leak 1
checkrng L -
a--pneumatic
I
siystem? ,
I 1 I \
I
1
I
i
, I I ' I '
11. ; What sy'stems are employed to measure temperatur~?
I , /
-
L- - // /
-1
VACUUM SYSTEMS
De-icer boots and inflatable seals use vacuum to ensure complete deflation
when selected to that configuration.
This is placed in the airflow close' to the fuselage, and fitted tb some small
aircraft. I
I
/ I
1 - -
I '
P
-
I I
VACUUM GAUGE
The supply line to the vacuum system is connected to the throat of the
venturi. The drop in pressure a s the airflow passes through will cause a
suction a t the throat a n d a suction in the vacuum line.
Throughout the normal operating airspeed range the velocity of the air
through the venturi creates sufficient suction, but when taxiing, or a t the
start of the take-off r u n , or a t the end of the landing-run the negative
pressure is insufficient for the system. There is a wide range of airspeed
that the venturi throat will experience, so the vacuum pressure to the
system will vary.
r --
- -- -
I3nginei~rivgn
Vacuum urn^'
1- ---
-
1
I
/
,
/
I
J
-
I
-
I
The vane type of engine driven pump shown in figure 49 is the most
common source of vacuum for systems that are fitted to general aviation
light aircraft. Can be fitted to the accessory drive shaft of the engine or
I belt driven on piston engines. On a piston engine aircraft it is connected to
the engine lubrication system, the oil providing a seal, cooling and
lubrication.
Another type of engine driven pump is the dry vacuum pump. This pump
has no lubrication, a n d the installation requires no lines to the engine oil
supply and therefore no air-oil separator or check-valve. Its principle of
operation is the same a s the oil lubricated pump.
The disadvantage of pump and venturi systems is that with altitude air
density decreases and vacuum pressures are more difficult to achieve.
With pump systems routine maintenance is required for filters, pumps,
valves, pipework etc.
AIR IN AIR OUT
4 VANES t
HEADING
\ INDICATOR
FILTER
SEPARATOR
ATTITUDE
INDICATOR
TURN 8 BANK
RELIEF RELIEF
VALVE VALVE
RESTRICTOR
VALVE
The pump size and capacity may vary from aircraft to aircraft and depend
on the number of gyros/equipment to be operated.
- 52 -
rnoodull l A-1435
The air is drawn into the system via a filter and, via pipelines, will be
directed to equipment/instruments. It will impinge onto the turbine wheels
(that are part of the gyro on gyro systems) and cause them to rotate, or
give vacuum to services that require it.
Various components are fitted to the system for system protection etc.
Air-Oil Separator
The oil and air from the vacuum pump are exhausted from the system
through the separator in order to separate the oil from the air and return it
to the engine lubrication system. The air is then vented to atmosphere.
- 53 -
moodull l A-1436
The purpose of the check-valve is to prevent possible damage to the
instruments and operation of services in the event a reverse flow of air.
Fig. 52 CHECK-VALVE
Selector Valve
I
Restrictor Valve
Air Filter
This filter removes debris from the air flowing Lo all instruments, which
also have individual filters. If the filter became blocked, the result would
be a reduced airflow and a lower reading on the system's suction gauge.
Most filters have a bypass valve fitted that opens in the event of a blocked
filter element.
Suction Gauge
In many aircraft there is provision for the pilot to check the vacuum
system a t more than one point.
Suction
I 1 //'
I
I *,
--
The left a n d right engine driven vacuum pumps and their associated lines
and components are isolated from each other and act as two independent
vacuum systems. The vacuum lines are routed from each vacuum pump
through a vacuum relief valve and through a check-valve to the vacuum
fbur-way selector valve.
From the engine four-way selector valve, which permits operation of the
left or right engine vacuum system, the lines are routed to a vacuum
manifold. From the manifold, pipelines connect the vacuum operated
instruments into the system.
From the instruments, lines routed to the vacuum gauge pass through a
turn and bank selector valve. This valve has three positions; main, left
turn and bank, and right turn and bank. In the main position the vacuum
gauge indicates the vacuum in the lines of the artificial horizon and
directional gyros. In other positions the lower value of vacuum for the turn
a n d bank indictors can be read.
TURN & BANK SELECTOR VALVE
\ VACUUMGAUGE
PILOT'S T & B
CO-PILOT'S TURN
8, BANK INDICATO
CO-PILOTS ART
HORIZON
Air is allowed into the system via each instrument - suitably filtered of
course.
A separate system not too unlike the one described above can be used to
operate the vacuum side for de-icer boots. The vacuum pumps may be
electrically driven and there may be a vacuum reservoir with the supply
lines connected from the reservoir to a cyclic valve on the de-icer system.
Like all testing, the best way is to consult the manual and carry out a
functional test. This would require a n engine run for engine driven pumps
and a vacuum/pressure supply for the system.
Leak tests are carried out much like a Pitot/static system. Instruments
may be blanked off (but check the AMM) and vacuum applied slowly until
the required test gauge reading is obtained, this should be maintained over
a period of time.
If the system cannot keep the vacuum for the specified period, the leak (in)
m u s t be traced and rectified.
Remember, for leak testing do not use any leak testing solution such a s
Snoop. Any leaks in the system would suck the solution in and this may
cause serious problems with instruments/components.
- 57 -
rnoodull l A-1440
Answers to Self Assessment Questions
SAQ 2. Blue crystals indicate dry silica gel; pink crystals indicate that they
are saturated and require replacement (they can be re-activated by heating
gently in an oven). If the filter becomes saturated frequently, it might be
indicative that the oillair separator is full or the compressor is loosing too
m u c h oil. It requires maintenance action.
SAQ 3. Typically these pipes are in the region of 1 to l/z inch in diameter
(25.4mm to 12.7mm). In most cases the pipes are fabricated from steel,
usually stainless.
- - -- I
SAQ 7. A single acting actuator could be prone to 'blow back' from the
flight effects (on a simple hinged flap system), meaning that it would have
to be kept pressurised to keep the flaps deployed - though on some aircraft
this might be used.
SAQ 9. Two reasons really, firstly switching an earth is less likely to cause
a spark so the contacts of the micro-switch are less prone to erosion and
radio interference is reduced. Secondly all lamps on the flight deck have
got a common supply which means that they can all be dimmed together
from one dimmer switch.
SAQ 10. Lowest bleed air occurs when the engine is running at idle. The
crew would select the turbo compressors on during taxi. They would leave
them running until the gear is retracted, and would start them again on
the approach to landing.
SAQ 11. A jet engine relies for its thrust on the high speed air leaving the
rear of the engine. A turbo-prop engine uses most of its energy (about 90%)
to drive the propeller so only a residual thrust of 10% is obtained from the
jet efflux. Affecting this efflux in any way (scooping some of this away for
anti-icing for example) h a s very little effect on the overall efficiency of the
engine. Besides the problems of the high velocities and temperatures in the
efflux of a non prop jet engine any disturbance of this airflow would have a
more marked effect on its performance.
Gasses leaving any jet engine are toxic and corrosive so they are best
ducted out of the aircraft as soon a s possible. The ram air leaving the heat
exchanger {unless there is a leak) is clean (and hot).
I I
1- '
/
/' 1 '
i
I
SAQ 13. Initially it could be considered that the system wb?ld fail,,but this
is not the case. The torque motor wi8 Btop moving, but [ t h e i r is still
1 1
coming off thefingine. The r e d l a t o r s qave already broGght the pressure
down tp 55-6Spsi and this will 'back off tide bleed signal arid close the HP
valve1 at a 1
slikhtly higher pre$spre -/' 1
than $e torque motdr bould do. This
\__
tyge -
L
of-redundancy
- --
is common irelectronic
--
-
systems. -,
- I
-
SAQ 14. Consider the valve itself, it is sprung loaded closed, pneumatically
opened - that pneumatic pressure is coming down the sense line (that is
leaking). There will not be as much pressure in chamber B so the valve will
i
stay further closed than before. The effect of this is to reduce the system
pressure in the pneumatic control due to the fact that the apertures are
set. In the digital control, the Air Supply Unit will see the reduced pressure
and apply more sense pressure to open the valve. It will sense the failure
(and report it.
SAQ 15. After start the temperature would rise above the normal operating
temperature, possibly getting close to the over temperature limit. But it
would eventually stabilise. As the engine is throttled forward (on take-off),
and the H P valve closes the temperature would drop well below the normal
operating temperature. During cruise it would appear fine but might re-
occur after landing on the taxi in, as the H P valve opened again.
SAQ 16. Ducting is usually made of thin gauge metal and is susceptible to
damage. Care with handling and installation is required. Consult your
AMM but as a general guide:
SAQ 17. Having the same excitation voltage means that any fluctuation
in that voltage is felt at both coils and will not effect the reading on the
instrument. -
CONTENTS
Page
~ n s w k r sto SAQs
I - /
'
1
II -I
- ,\
\
\
1 1
I ' , '
' I I !
I
I 1 , I j
- /
,
I
DOMESTIC WATER SUPPLY SYSTEMS - GENERAL
Have to meet the requirements of CS25 (was called JAR25, then EASA25, now
called CS25) (CS = Certification Specification) in that they must not constitute a
hazard to the aircraft and all replenishment connections should be so designed
that misconnection of water services to any other systems is not possible.
Water is used on aircraft for many reasons, and a s such can have different levels
of water quality. Water i s used for:
* Drinking. Has to have a high standard of cleanliness and quality control.
* Washing - using wash-hand basins (sinks).
* Galleys. Water for galley sinks, soft drink dispensers and makmg hot
beverages (tea, coffee etc).
-
*ILTojJets.The flush system-fEthe
, -
vacuum type toi1ets.r --
\ r
I I
* IIHhrnidifiers.
' 1
For h u m i d q n g the air for air conditioning.
1 1
I I
I 1
I
* cQolingheat exchangers. '&,r conditioning heat exchanger units may use
water for additional cooling.-This h$y not come from the @mestic water
3
,sdpplybut taken straigh frlomthewater extractor.
1 /
\
1 /
I '
I
1 1 ,
* Engines -/?ater/rnethan&l ibjection for'jet engines. ~ h d ?system may have
kts own tanks and supply/system. / I
i- - /
I \ - //
Theifast three are not part of tj.$sbookas-they are covered elsewhere in the LBP
books but have been include to give an overall picture.
The drinking water system (sometimes called Potable Water) consists of:
* Storage tanks. Sufficient water has to be stored for the flight duration. The
tanks and system must protected from icing, if the is a risk. A system h a s
to be provided to allow draining, flushing and refilling of the tank(s).A
contents system i s provided for the crew.
* Heating. The water has to be heated to the right temperature for hot water
taps (galley and toilet sinks) and has to be hot enough to make drinks with
(galleys). Note that a tap is called a faucet in American aircraft manuals.
* Cooling. Water for drinking fountains require the water to be cooled.
Figure 1 shows a schematic of a typical system. Study the drawing carefully and
note the following: the location of the tanks; the provision for filling and draining;
the supply to the toilet wash-hand basin, galleys and drinking fountain; the tank
pressurisation system to include APU and engine bleed via an air compressor and
the various indicators.
-2-
moodull l A-1446
Storage Tanks
Figure 2 shows a typical water tank installation. May be made from stainless steel
or glass re-enforced plastic. Some aircraft may have just one tank, others will
have more than one. The tank/s may be positioned vertically or horizontally.
Tanks are usually installed under the passenger floor in the freight bay regon. In
some aircraft they may be positioned elsewhere such as in the space above the
cabin ceiling. If in the freight bay CS25 stipulates that they must be separated
from the freight bay potential fire region in some way and this is normally
achieved through use of fire blanking material such a s glass fibre.
The tank shown has re-enforcing bands to strengthen the tank and provide strong
points from which the tank can be secured to the airframe.
In cases where the tank is suspended from the floor beam structure, the fmtures
may well be some form of structure fuse connection, that allows the tank to break
free a t times of high deceleration (forced landing, for example). This is to prevent
the weight of the tank collapsing the floor structure and pulling passengers into
the freight hold. Care needs to be taken to ensure the correct bolts are used.
Tanks will also have connections for distribution, fill (and overfill), draining and
air pressurisation. Notice also that it has an attachment pad and some form of
quantity transmitter, providing the necessary information to cabin crew and
ground crew.
rnoodull l A-1447
Tanks normally come as a pre-inspected unit from overhaul, the panels a t the end
are for inspection purposes.
SAQ 1
You have to carry out a detailed visual inspection of the structure behind the
tank. Would you consider it necessary to remove the tank and if so list the
procedure for removal and refitting?
The outside of the flexible pipe is usually fabric reinforced to brovide additional
strength and give a small measure1of protectipn against freezing. ~ h e _ rfreezing
--e is
a problem,
1
ribbon heaters are fitted.
t,
I
I 1
I
THERMOSTAT
l T 5 V AC
The freight hold of an aircraft is usually heated, but if, in the area of the water
tanks, it is not, electric heaters are fitted to prevent freezing of the tank and/or
pipes. Ribbon heaters provide a constant, low power heat source. There is no
switching and as aircraft power is applied the heaters come on. They are
sometimes ganged with the drain mast heaters for power supply purposes.
Removal/refitting of these pipes is the same as any other system pipe-work and is
covered in module 7 of the EASA part 66 syllabus.
Often, a t the system connection between the system and the galley/toilet modular
units, a quick release (self-sealing) fitting is used to allow easy removal of the
toilet/ FCey unit. Sometimes the distribution system has anisolation valve in the
f-
cabin and the Cabin Services ~ i r ~ c t cb qc\ i f required, shut2off the water to the
entire aikcraft. (Boeing 707/720 and the early 747 had this facility).
I
I I I
Each wash hand basin h a s its own water heater in the line to the hot tap. Figure
4 shows a typical water heater installation housed in the area under the sink
cabinet.
Each water heater h a s a capacity of about 3 pints (1.71) and heats the water in a
cyclic action. The water tank has the following equipment fitted:
* A O N warning light.
* A O N / OFF control switch.
* A n overheat reset switch.
* A pressure relief valve.
* Supply and feed connections.
OFF-ON LIGHT
*.
- -
r - - 1 OVERHEAT
115VAC
I I OFF SWlTCH
I &,
I 420 WATT H ~ A CYCLE
T
I HEATER I
SWIT'H
L---A
CIRCUIT
BREAKER
HEATCONTROL -- - . -
SWITCH
PANEL
I
I
Figure 5 shows the water heater control circuit. Study it f o r a moment. When the
heater is switched on (115v single phase ac) the light will illuminate and the
heater starts to heat. The current flows through the cyclic switch (a thermostat) at
the bottom of the tank which is closed and so power is allowed through the heater
elements.
As the water temperature rises to about 50°C (125°F)the cyclic switch will open
and stop the power to the heater elements. Notice, however, that the light will
remain illuminated. If the cyclic switch should malfunction, the temperature of
the water will continue to rise, as the heater elements will remain powered. To
prevent an overheat condition and possible fire another switch is installed (by
regulation), called the overheat switch. At about 87°C (190°F) the overheat switch
will open and latch. This will stop the power to the heating elements and the light
will go out.
The heater will require resetting - by pressing the reset button. The reset button i s
located on the tank and is usually covered with a rubber bubble. The water
heaters are powered all the time power is available on the aircraft.
rnoodull lA-1450
If the system h a s been drained and the heater C/B's have not been isolated, the
overheat switches will operate and will require resetting - after filling the system
of course.
The possibility of fire is small, but the water heater is usually protected with a
'wax stat' fire detector and fire bottle and care needs to be taken during
maintenance on the water heater that this nozzle is not dislodged. (More
information on the fire extinguisher is available in the book in this series entitled
Fire Protection.)
The on/off switch allows the heater to be locked out of operation for whatever
reason.
The over pressure relief valve must never be touched. It is a core plug type of valve
and will, should the pressure rise to about 140psi (965kPa),blow to relieve the
pressure in the water heater. This will cause a water leak, which would need
isolating at the toilet shut-off cock. If the water heater pressure relief valve has
-
operatedzthe heater requires replacement,,
\ - and you will need to investigate the
--
cause! I
I \
\
I 1
Removd, of the water heater, and Kor that matter any component in the toilet area,
doesn't require a full system dr- a s the:tqilet has its own slo~)cock,usually
locate? in the sink cabinet areal ~aving'isolated the water heater by/&ipping and
tagging the appropriate C/B, the h-tcr-isremoved in much the -e/way a s any
system component. The basics of this covered in SAQ 1. I 1
rnoodull lA-1451
Drinking Water Cooling
Water for drinking fountains will normally require cooling. Figure 6 shows the
circuit diagram of a cooler.
200v three phase ac supply is used to drive a motor which when the water
temperature rises above 10°C (49°F)will drive a fan to blow air across the
thermoelectric units, which uses energy change entropy to reduce the
temperature of the water. The motor is controlled via a control thermal switch
similar to the heater circuit already described. The transformer rectifier (the 2
delta windings in the drawing) is used to change the 115v ac into 28v dc for use
by the thermoelectric units.
A s the system is removing heat from the cooler, so this heat energy is dissipated
by the motor fan. Should the control switch fail the unit might overheat so an
additional switch is added that breaks the circuit at a higher temperature.
- - -
, I
1 I
Contents Indication I
I
The contents of the water tanks need to be relayed to both the cabin crew for use
during the flight and the ground ctew for recharging purposes. l ~ r o u n dcrew
seldom dse the contents gauge a t the fill pdint now as reguladions regarding
drinking water dictate that the system rnustibe full for departure. -
1 I \ I
Figure 7 shows a n indicator and figure 8 shows what is now a fairly common style
of contents indicator system. It consists of a float with a magnet riding u p the
outside of a sealed tube containing several reed switches. A s the magnet passes a
reed switch it closes and this signal is sent to the signal conditioner for onwards
transmission to the cabin crew.
In the case of the latest aircraft where the cabin systems are provided centrally
through a digital Cabin System Control Panel, the water contents information is
passed to the cabin file server and converted into digital signals for display on the
CRT/flat screen display on request.
I
L
7
T -
- - - - -
' I
-
, I -
l 1 I
I I
REED SWITCHES
rnoodull l A-1453
System Servicing (figures 9 and 10)
Replenishment of the water is carried out from the water service point usually
located under the aircraft fuselage, near the tank location and away from any
toilet servicing panels. To fill the system the water is connected to the fill
connection and the fill valve is pulled to turn the valve to the service position.
Water will flow under pressure from the tank maintenance rig to the tanks and
they will start to fill.
A s the tanks reach full the water is forced u p the stack pipe and through the
overflow and will start to flow from the overflow port on or near the service panel.
SERVICE
PANEL
]REPLENISHING POSITION^ [NORMAL FLIGHT MODE
-
'
- - -- --
I
-1 - -
I/
Fig. 10 TANK FILLREFILLSYSTEM
I
SCHEMA~C
I I
I 1 1 1
' I
I I ' I I
~ r a i n i is
l 1
h ~also carried out from the wafer Service panel. ~ i r sthe
I
t filljhandle is
I
pulled;which rotates the fill/vent valve and vents the tank ( e n s u r e m a t is un-
pressuribed). The drain valve is t h p t a t ~ d which,
, a s it is lbcated a t t h e bottom
I
of the sistern, allows the water to drain b$\ g?avity. This wateb Should not be re-
1 ',
~
I
used. I I I I
i I
On lmLd\aireraft, there may well
j ; I
hie-tw-o,or
more drain points under the fuselage,
r'
eg one-in front-of the wing section-anddone,behind. This all&s for the fact that
sometimes the pipe-work h a s to rise to get over the wing centre structure.
The sterilizing solution (typical a chlorine like Puregene@)is added to the flow of
water during a fill operation. The tanks are then pressurised and all taps and
toilets are operated to ensure that the sterilised water flows in every part of the
system.
You can tell that the solution has passed through the tap when the flow of water
from it turns a milky colour. It also has a distinctly chlorinated smell. This
solution is left in the system for some time, then fully flushed out.
Note. When filling always ensure that the water has come from a known drinking
water source and that the replenishing cart is exclusively used for drinking water.
Tank Pressurisation
Compressed air is fed into the tanks to force the water u p the risers to the toilets
and galleys. This supply of air will either be from the aircraft pneumatic supply, or
a purpose built compressor. Sometimes on large aircraft both are used, with the
compressor providing backup for the main system (figure 11).
-
AIR
COMPRESSOR
FILTER
pJi=@
- INLET
AIR
AIR - CHECK
- FILTER VALVE
I I
AIR CHECK
FILTER VALVE PRESSURE
PNEUMATIC SYSTEM / RELIEF
CROSSOVERDUCT - -- I - ,VALVE
I \
I ,
I
I
I PRESSURE
SWITCH
- -
Notice also in figure 11 that there is a number of Non Return Valves. Also take
note of the riser loop, this i s fitted to prevent water from entering the compressor
system from the tanks when the compressor is off.
Drain water from the sinks (galley sinks and wash hand basins) is dumped
overboard through a series of pipes and heated drain masts. Figures 12 and 13
shows a typical sink waste disposal system.
I
- 1 --- _ r - -
As thk sihk plug is lifted - u s u ~ ~ bl y a, s m a l l lever, the water flows down the pipe
to the ldqain mast. The water is then allowed',to flow overboard. This presents no
environmental issues, as the wdter is moderately clean and soon disperses in the
atmosphere. (Toilet waste water,I [Blue water]' is never dispose'd of overboard, but
kept on-board in tanks to be emptied-when on the ground.) 1 Lp 1
-
I -- -
FOUNTAIN-
DRAIN NOISE
GREY WATER
rnoodull l A-1457
This system presents a couple of problems in that the noise generated is high and
the loss of air from the cabin causes inefficiencies. A poorly fitting plug, for
example, will cause a noise all the time and lead to fuel penalties (more air being
bled from the engines to make u p for the leak).
The noise problem is largely overcome by putting a muffler (very similar to a car
exhaust silencer) in the outflow line. We must also ensure that the plugs fit
correctly and that the rubber bung is not perished.
The loss of air problem is harder to overcome and one recent solution is to provide
a Gray Water* drain valve (figure 13).
* The term Blue Water is often used to describe liquid from the toilets and Gray
Water, liquid from the sinks. Blue water waste is kept on-board, gray water waste
is dumped overboard. Gray water is a Boeing term and hence the spelling.
On the ground the valve opens completely. When the aircraft becomes airborne,
the gray water valve closes andprevents all water from exiting thepGrcraft.
-
1 ' !
I i
\
I
,
ISOLATlONl ISOLATIONVALVE
I
FWD FWD
FORWARD SYSTEM
DRAIN LINE
GRAY WATER
DRAlN
MAST (2) -.)
Drain Masts
The sink waste passes overboard through a drain mast. Figure 14 shows a typical
example. The drain mast ensures that the water is removed from the aircraft and
not allowed to blow back onto the fuselage where it would freeze on the airframe
structure and become a hazard.
The ambient low temperature would also freeze the water inside the drain mast
which would cause it to become blocked.
To prevent this the drain mast is electrically heated. Two temperature settings are
involved, one on the ground (low) and one in the air (high) (operated by the weight
switch). The lines down to the mast are also heated - by ribbon heaters - also to
prevent freezing and blockage of the system.
CAUTION. These masts can get very hot and are a burn hazard. Do not touch.
rnoodull l A-1459
Drain masts are susceptible to being damaged and put out of alignment both on
the ground and in the air. It is very important that they are inspected for damage
and correct alignment on every walk-round inspection.
A second issue that can arise from drain masts, is that if the heating circuit fails,
the water can freeze and cause damage to the composite fairings that they are
often mounted on.
All structure around and behind drain masts should be inspected for debris
damage, corrosion (metal), water damage (composite) and security. If external
frozen water is suspected then all structure and engines etc aft of the mast should
be inspected for impact damage.
TOILET SYSTEMS
Unlike the grey water waste system toilet waste (or blue water) must never be
deposited overboard. Besides beingunpleasant it presents a health hazard to all
who are below the aircraft's flight path; So much so that se;ei-e fines are being
imposed on operators whose aircraft have had blue ice' found on them, or blue
ice deposits having fallen from them. (The term 'blue' comes fro+ the cblour of the
chemical used in the toilet system!)
/
I
-
Toilet systems can be classed into three main groups. These &re: -
1 I I
* I I
Removable toilets - often idled 'Elson dtyle'.
* Re-usable liquid flush type.
* Clean water flush type, or vacuum flush type.
- -- -- -
Servicing this type of toilet is simple, and involves removing the toilet container
(sometimes via a servicing panel from outside the aircraft, sometimes from inside
by removing the decor paneling around the toilet), emptying it (into the normal
airfield toilet system), cleaning, recharging with a small quantity of fresh
Raquasan, replacing and securing. The container itself is clamped to the floor to
prevent movement and spillage in times of turbulence.
The area within the decor paneling, the floor and the structure must be kept clean
and care must be taken not to spill any of the liquid on the aircraft. Urine (uric
acid) is very corrosive.
rnoodull l A-1460
Fitted to smaller executive jets, often within a plush decor paneled unit within a
lavatory unit. The container may have a lightly sprung loaded (closed) stainless
steel flap on the top which must be aligned with the toilet seat.
This h a s a flushing system which uses the existing liquid (disinfectant and urine)
within the container under the toilet. A typical toilet unit is shown in figure 15.
Most large commercial aircraft manufactured up to about the late 1980's have
this type of toilet system.
The waste tank is located directly beneath the toilet pan in much the same way as
the removable toilet was. The tank is large and, typically, can hold u p to about 40
gallons (1801)of waste (on long flights this can become full which causes toilet
cubical carpets to become wet with possible structure contamination). Sometimes
the tank is a double tank anCzill-hTve-two toilet pans in two separate cubicles.
The tank% usually fabricated frofiglZiis ,re:enforce ldastic$t [can be stainless
steel, q d h a s metal tie down points. 1 ,
I I , I
1
I
' ,
I
I
THREEPHASE
PUMP MOTOR
FLUSH LlNE
- 17-
rnoodull l A-1461
Local repairs to this tank are often not possible due to the build up of waste over
time, and as such satisfactory repairs can only be carried out a t an overhaul
facility.
Figure 16 shows a schematic view of the toilet system. Note that the tank h a s a
soil pipe connection underneath to connect the tank to the waste servicing point.
A dump (or drain) valve is located on the bottom of the tank and is operated by
Bowden type cable from the toilet-servicing panel on the underside of the
fuselage.
- 18-
rnoodull l A-1462
The tank is filled with a 'pre-charge' which is a small quantity of Raquasan or
similar solution. (The actual solution and quantity is specified in the AMM
chapter 20). This is added to the tank from a connection on the servicing panel,
through pipe-work and a non-return valve in the ground flush line.
The toilet bowl(s) is/are bolted onto the top of the tank usually with captive nuts.
The unit h a s a separator (a flap) that keeps the waste in the tank from being
visible. Both the separator and the bowl itself are fabricated from stainless steel.
There is a flush ring in the bowl connected to the flush motor, which allows
flushing of the toilet bowl.
The waste tank h a s a fume extractor system connected to the lav7and galley vent
system to outside.
Flushing i s achieved using a fixed speed three-phase motor, fitted outside the
tank and connected to the pump by a shaft. It alternates rotation direction on
each-flu* cycle to help prevent blockXge.~~ound the pump thereis a filter and
separitqr mechanism that separates thk\solids before allowing t h e motor to pump
I
reasonably debris free liquid to thk flush ;ink.
I
I
I
1
FLUSH
LINE
WASTE DRAIN TUBE
DRAIN VALVE
The flush cycle is initiated by pressing the flush switch (lever, mounted on the
cubical wall). This sends a signal to the timer control, which runs the 3phase ac
motor for about 10 seconds. A s the motor turns the filter screen is rotated against
the stationary wiper blade, thus removing any large particles of solid material and
keeping the filter screen clean.
FLUSH MOTOR
\
CONNEC
PLATE
PUMP
PORT
WIPER BLA
PERFORATED FILTER
BASKET
FLUSH MOTOR
ELECTSUPPLY 3 PHASE FLUSH MOTOR
1 I
-
-
,
,
- - -
-
SOLIDSTATE
IIF- - CIRCUIT
L-
TIMER
---------.------
mJ
TOILET FLUSH
CIRCUIT DIAGRAM^ HANDLE
The pump impeller a t the same time draws fluid through the rotating filter and
into the flush line. This fluid is moderately debris free (particle size about 300
microns) and the chemical content in the toilet is high.
At the end of the flush the separator (flap)at the bottom of the bowl returns to t h e
'up' position by light spring pressure.
The logic timer unit will reverse the direction of the motor on alternate flush
cycles; this helps keep the filter screen clean. (The relay operating the ganged
switches of the two phases in figure 18 is the reversing mechanism).
CAUTION. Before operating the flush motor for maintenance purposes, make sure
that there is sufficient pre-charge (liquid) in the tank to prevent the motor from
running too fast and overheating.
SAQ 2
After a flush cycle the motor continues to run. List your actions to rectlfy the fault
and list the possible causes.
Servicing
Drainin;, flushing and refilling is carried but outside the airdraft from beneath the
fusela'ge and toilet cubical maintenance is carried out from Aside the toilet
cubic& itself. We shall deal wit4 the drdi.n?hg/flushing/reflldngof th6 system now
and the cubical maintenance will lbedealt'with after all toiled systems have been
covered.\ \ '\ I -
'
I
I
I
I
I
I
I
I
1
I FLUSH PORTS /
Draining/ flushing/ refilling is carried out from a panel a t the bottom of the
fuselage. Figure 19 shows a typical toilet-servicing panel. There will be one of
these located beneath each tank or one fitted to service several adjacent tanks.
Figure 19 shows one for a two tank system. Note the two flush ports; the two
drain valve handles (connected to the drain valves) and the single drain connected
securely to the drain line of the ground servicing trolley.
Normally the tank is drained and re-charged after every flight. To empty the tank
proceed as follows:
1. Always wear protective clothing and ensure anti-tetanus jabs etc are
- -
up-the-date. Check the operators/local airfield instructions for the
anti-infection injections tKat are required. Make sureyou have no
open wounds or scratchesT
I
4. With the waste trolley drain pipe connected the secondary valve can
be opened (on some aircraft the donut plug is operated by an external
lever). Sometimes this takes the shape of a donut plate, but more
often it is a separate valve in the outlet line between the waste tank
main drain valve and the outlet. The appropriate tank drain valve
handle is now pulled and this (via the Bowden cable to the top of the
tank) lifts the drain valve and allows the waste material down the
outlet and into the tank of the servicing trolley. Some service vehicles
have a suction facility to aid in the removal of the waste.
5. Once the tank is empty and before the main drain valve is closed the
tank is flushed by applying water pressure to the fill connection of the
appropriate tank. This water travels u p the pipes and to the ground
fill connector on the tank top. From here it is passed into a perforated
pipe that sprays water around the inside to clean the tank.
6. The main valve is now closed, the drain pipe disconnected and a pre-
charge (a mixture of water and a strong disinfectant) is added (typical
quantities - 7 gallons 13111).Check the actual amount in the AMM.
The toilet system is now 'serviced' and ready for the next flight. Prior to this
operation it is a good idea to have the toilet bowl cleaned first by the cleaners
when they "service7'the toilet cubical.
1 * (
I I 1 f
t
COMMON VENT FOR
-
GALLEYS AND---
L J I
-
I
--
,
\ LAVATORIES
- - .
I 1 I ' \
' I I 1
I ( ,I I !
'
I
,' 1 I I
I
I
\
[ ' / I
lAs y
I
TOILET
I- >
I
TOILET :
I .-. I
1 L- ,
- --
I
\
SERVlCE PANEL
Periodic maintenance includes filling the tanks completely with a strong cleaning
solution, checking for leaks, operating the flush motors and draining. Any leaks
must be rectified. Any blockages must be cleared and all motors etc function
tested. Unserviceable components are changed.
rnoodull l A-1467
One of the main problems with this sort of toilet was that the waste line
connections and plug tend to become perished with being in contact with the
chemicals etc). This can cause the contents to leak, the situation being made
worse by the pressurisation effects in flight.
The whole area must be carefully inspected from the waste tank down to ensure
that there are no leaks. The chemicals are strong and are very corrosive
particularly to aluminium and its alloys.
In recent years the number of plugs and secondary sealing devices have been
increased a n d you may well find yourself performing a vacuum test on the waste
line to check its ability to seal.
A simple test to check that the secondary sealing valve is leaking (or not) (the one
between the waste tank drain valve and the drain line outlet) is to add a quantity
of clean water to the tank. Close off the secondary sealing valve and open the
main tank drain valve - with all other caps and seals open/removed from the
drain pipe. !The secondary sealingvalve
- should not leak. If it doecit must be
replaced.
' I
I
\
I
Afterwards close the main tank drain valve, qpen the second& sealing valve,
allow the water in the pipe to drain and check that the main tank drain valve does
not leak. -
--
/
' I
-
Of course, this will all be specifidd in the AMM.
' I
1
A problem with these toilets is the fact that they tend to spill/overflow during
flight (particularly a long one) and the fluid works its way down onto the toilet
underfloor structure. This area requires special attention and anti;corrosive
treatments and often requires repair or replacement. You should take extra care
whilst inspecting these areas. The same corrosion problem applies to galley areas
- though to a lesser extent.
- 24 -
moodull l A-1468
RFERENCE LEVERS
WASTE PIPE
S A F E R PLUG
I
I - -
, 1 1
/
Most l ~ g~6Wmercial
e aircraft-built-sin-@'the late 80's uselthistype of toilet.
The system uses vacuum to drain the toilet bowl assisted with a little (clean)
water. The waste from the toilet is not stored beneath the unit, but remotely in a
separate large tank. This tank (or tanks) is typically located in the cargo hold.
Figure 22 shows a schematic of a typical system. Note the vacuum supply to the
tank obtained from a vacuum blower, which automatically cuts out a t altitude
(typically 16,000ft) and differential pressure takes over through the one-way valve.
Note also the tank level sensors, pipe-work to the toilet bowls and the water
supply from the potable water system. The anti-syphon valves prevent water
syphoning back to the water system.
Suction to the tank is via a separator to prevent liquid etc from being sucked out.
This applies a vacuum to the tank/s and pipes u p to the flush valves. When the
valve is opened (electrically) the vacuum, assisted by a small quantity of fresh
water causes the waste from the toilet to pass down the pipe to the composite
tank.
- 25 -
rnoodull l A-1469
FLUSH
FLUSH SWITCH ANTISIPHONE CONTROL UNIT
FLUSH VALVE
VACUUM BLOWER
- FLUSHING
WATER
SUPPLY
SHUT-OFF VALVE
VACUUM BLOWER
ALTITUDE PRESSURE
SWITCH
LAV INOP LIGHT
ATTENDANTS' PANEL
TANKS
STRUCTURE
Note the rinse and drain pipework, the function of which is similar to that of the
re-useable liquid flush type system.
- 26 -
rnoodull l A-1470
Special large diameter stainless steel pipes are connected to the tank bringing the
waste from the individual toilet units. There are usually several tanks and the
toilets they serve are split u p around the aircraft so that a full tank doesn't lock
out an entire section of the aircraft. The level sensors give a "tank full" indication.
On some aircraft there are two vacuum connections to each tank. One is
connected to a vacuum blower that provides vacuum on demand. The other is
connected to atmosphere and serves two purposes. Firstly it allows the blower to
vent somewhere and secondly above 16,000ft the cabin differential pressure is
used to provide the vacuum instead of the blower.
Figure 23 shows an example of tank location below the aircraft floor and figure 24
shows a typical toilet bowl unit. It is made of Teflon lined stainless steel. Note the
anti-syphon valve, flush valve, rinse water valve and flush control unit. The
drawing does not show the stainless ring that fits just above the toilet lip. This is
to prevent the complete sealing of the unit with a person sitting on the toilet -
,
designed as a safety measure during the flushing cycle, when the vacuum
I I
SUPPLY PLUG
Operation
The operation of the system is initiated by operating the flush handle which closes
a switch. (The handle, incidentally must be located out of reach of the passenger
whilst they are sitting on the toilet). Figure 25 shows the run cycle of the system.
- 27 -
rnoodull l A-1471
FLUSHING HANDLE
VACUUM BLOWER
WATER VALVE
FLUSH VALVE
NEXT CYCLE
DELAY
SECONDS
The flush handle is pressed (momentarily).The water valve opens and sends a
squirt of high pressure potable dater via the anti-siphon tubk around the flush
ring to assist pan cleaning. The anti-siphofi tube prevents a& possibiliG of the
water getting back into the drinking water system. Now the flush valve opens and
the contents of the pan are sucked out and down to the tank. After 2 seconds the
flush valve shuts, but the blower continues tp run for a short time. A repeat flush
is inhibited all the time this is going on. I
SAQ 3
- --
An aircraft returns to the stand and the crew report that the toilets are not
operating. List your actions to rectify the fault.
The toilet unit has three valves, one anti-syphon, one to control the water suppl,
and one to control the vacuum flush (this has a handle to allow manual closure
should it fail in the open position.
A s the tanks fill, the liquid eventually covers the level sensors. These send signals
to the logic units of each toilet unit that feed into the specific tank. This signal will
prevent the toilets flushing and the crew would get a warning. The flight crew
would close the toilet off.
Level sensors tend to become soiled and this can lead to false readings, to help
prevent this the rinse jets are directed towards them. This means every time the
tanks are serviced, the sensors get washed.
/
- -- . -
' /'
Fig.
I
26
I ,'
\
--
i /A'
,
1
I I ~
Take a moment to study figure !26.-~ote&e'flush switch in the lavatory control
- -
unit. Note that its power supplycomes Born the ground serfice p'anel or the flush
control system flight via an AND logic gate if the sensors are serviceable and the
waste tanks is not full. Note the three-phase supply (one line shown) to the
vacuum blower.
Maintenance
The vacuum flush system, unlike the re-usable liquid flush system, has little
disinfectant fluid added. During servicing only a small pre-charge is used and this
means that there is a slightly higher health risk when servicing this type of
system because of the higher concentration of effluent to disinfectant.
The precautions that follow should be observed when-ever servicing any toilet
system irrespective of what type it is.
Precautions
* Ensure that your injections are up to date. The policy regarding
injections i s u p to the company and the risk assessment that h a s
been carried out. The injections could include anti tetanus, hepatitis
A and B, polio, typhoid etc. The risk assessment may have concluded
that these are not necessary provided all proper precautions are
carried out, but would probably have to be given after bodily contact
with contaminated fluids.
* Wear bio protective clothing to include disposable gloves, overalls,
face-wear, etc.
* Use special dedicated "toilet" tools (not your own tool-box tools).
* Plastic bag any removed items (articles of clothing, needles etc that
may be found in the toilet effluent and clearly label as 'Bio Hazard'.
Inform the authoritiesif any banned substances (drugs etc) are
-- -
found.
* Return all tools to stores in labeled plastic bags. I
Note. For most operators the ramp servicing of the toilets, from cleaning the toilet
cubicles to draining/recharging the systems, is sub-contracted to service
companies. This means that specialist teams (cleaners for the toilet cubicles and
separate toilet draining teams), will arrive at your aircraft after landing suitably
prepared with all the correct equipment etc to carry out the task/s.
However, it is your aircraft and it will fly on your CRS so you must know what is
required.
The most common tasks that are performed on vacuum flush systems would
include removing and cleaning the single point sensors. Also flushing through the
pipes with acetic acid and crushed ice to clear blockages is another fairly common
task. (It is general considered that the pipes are not big enough as blockages are
frequent.)
TOILET CUBICLES
Daily servicing is usually carried out by the cleaners, but like the toilet systems
themselves they are ultimately your responsibility.
The cubicles may come in various forms, but for most large commercial aircraft
the unit is fairly standard - this applies whether installed in the main cabin of the
aircraft or business class or first class.
Regulations do not permit smoking in the toilet cubical. Also fires have occurred
in the towel bin due to people putting cigarettes in the bin.
Therefore smoke detectors are fitted (normally in the ceiling), giving aural and/or
visual warning to the cabin staff or flight crew (a regulatory requirement). The
smoke detector is operated continuously on the ground from ground power and in
the air, when the toilet and galley air extraction system is on.
-r --
I
- -
'
, r-
\ --
EMERGENCY,
OXYGEN , I
I
DETECTOR
GRILL
CABIN FLOOR
rnoodull l A-1475
In general the cubical will contain most of the following equipment - the
maintenance of which you are expected to know:
* A sink - usually made of stainless steel with hot and cold taps, soap
liquid dispenser, plug operating knob (between the taps - usually).
* Toilet bowl - stainless steel (Teflon coated for the vacuum type). On
the Elson type and vacuum type the bowl may not be paneled in,
though it is usually.
* Lights. A low power one that is on all the time aircraft power i s on,
and a brighter one that is microswitch operated when the door lock
mechanism is engaged.
* Mirror.
x Towel dispensers - for drying hands etc. May contain paper towels
- - -
linen towels. - ,
I
* Toilet roll/ tissue dispenser. ', I
,
I
* Used towel bin - stalinless steel &th a spring loac!iet$ lid. Because of
the potential fire hazard mntai'ns a self operating fire bottle, - check
the book in this series onFire Detection Systems.,
I I
* Ash tray -just in case someone walks in the toilet with a cigarette on.
Remember, smoking is not allowed in the toilets br &hen walking in
the aisles - though on m y fligfits smoking is b,mned altogether.
-
, - - -
I
L -
* A lockable door which can be unlocked from the outside by the crew
and when locked puts the cubical lights on and illuminates a n
external occupancy indicator.
* Toiletries draw or draws. These may contain:
-k
Single phase ac power socket.
* Microswitches.
- -
I r C_ORKOSION,
-- CONTROL \ \ ---
I i 1
All toilets (and galleys for that matter) haGe keta17sworst e d d y - wdter, with the
added problem of the chemical additives. Co~rosionis always a problem i n these
areas which is even more so in bld or geriatric aircraft. 1
1 ---
ad>
/
differenoe (pd).The structure uhdbr a toile; is the perfect place for corrosion to
start, d d due t o i t s lack of insqection accesd it can develop buickly. There is a
need tp provide/ektra protection for these &{as.
, c '
I
I
l 1
/ /
-
- -
'
/
/ / -
- - - -
The aircraft floor structure (including under galleys and toilets) may be made from
aluminium alloy 'clad' in some cases with a thin film of aluminium (al-clad),
composites or sometimes titanium might be used.
SAQ 4
rnoodull l A-1477
STA 2f33.5
FLOOR BEAMS
-
.
Fig. 28 TOILET UNDER 'FLOOR STRUCTURE - EXAMPLE BOEING
1 \
1
i I
I
Even if composites are used the seat tracks are still made of aluminium alloy for
strength and wear considerations.
Some floors under the galleys and toilets are titanium because it is almost non-
corrodable. It will corrode but a t such a slow rate that for all practical
applications it is deemed to be totally corrosion resistant.
Besides the normal anti corrosive measures applied to metals (eg anodizing for
aluminium alloys and cadmium plating for ferrous metals) additional measures
for under toilet floor areas will include:
* Corrosion Preventative Fluids (CPFs) applied to the structure.
* Floor panel clips taped to prevent scratching.
* Floor panels cushioned to prevent scratching and damage.
* Floor panels sealed to prevent fluid getting into the structure.
* Moisture barriers applied over the entire 'wet' area.
* Leaks in the toiIet system traced and cured at an early stage.
moodull lA-1478
Corrosion Preventative Fluid (CPF)
CPF is a water displacing fluid that adheres to the surface of clean (or primed)
aluminium and it's alloys. It is a slightly waxy substance that can either be
sprayed by aerosol can or by a 5 gallon (221) dispenser onto the structure. Care
needs to be taken during this operation, a s the fluid spray will damage the lungs
if breathed in. Use only in well ventilated areas and wear face masks. A thickened
version of the fluid is available for brushing.
Consult the AMM prior to application. The biggest draw-back with CPF is that it
acts as a debris collector. It will collect dust and debris as it is very sticky. During
routine maintenance and certainly prior to any structural inspection this needs to
be removed. Always record any work done (re-application etc) and clear all work
with a CRS signature.
PANEL AlTACHMENT
- -- --
I I
A
1 I
I
II
I
~ i
I
I
i
I
/
C O S M O L E Y 1060 /
I 2" VINYL TAPE /
I
FLOOR PANEL
/
I
I
1 I
I
/
L 1
i
L p p
i INTERCOSTAL ,'
, I
-
SUPPORT
COSMOLENE 1060
Floor Protection
Figure 29 shows the protective measures that might well be taken during the
fitting of a floor panel.
Note the tape which is usually some form of Vinyl, this protects the area around
the clip and prevents chafing and subsequent scratching. Foam is applied over
the top of the clips for two reasons; firstly it helps to prevent the floor panel from
chaffing the structure and it also allows some 'give' in the floor panel which is
mostly a comfort thing (for walking on).
Floor Sealing
Floor panels are sealed in a variety of ways using various materials depending on
where they are located and how often it is anticipated they will require to be
removed. For example, the floor panel at the entrance to a toilet may require
lifting fairly frequently to track down leaks from under the toilet tanks. Other floor
panels elsewhere in the cabin may not be
- -
lifted for many years. -
7- -
A n example method of sealing floor panels is shown in figure 30. The actual
method varies from area to area and between aircraft.
rnoodull IA-1480
Other Corrosion Preventative Measures
After all of the above h a s been carried out, the area is ready for the toilet or galley
complex to be installed. Prior to this a Mylar type moisture barrier is applied over
the entire 'wet' area to extend it to 3ft (lm) beyond the area in all directions. This
is totally water-resistant and prevents any spillage seeping through but may mean
that the liquid moves to the edge of the water proof area. So the trouble may be
moved elsewhere.
2'0.5 INCHES
0.1+0.2-nil INCHES
1- -- J
I
~
I
I
I
1
' I /'
1
i
'.
I
I
/ '
1 ' ' ,, I STARTITHE CORD AT THE AFT
OUTBOARD CORNER OF THE
_ --- I
- -
I
i--
' PANEL. INSTALL IT AS TIGHT TO
---THE PANEL AS POSSIBLE. WIND
'
-
11 \ 'RUBATEX TAPE
FLOOR BEAM /I.J
Fig. 30 TYPICAL FLOOR PANEL SEALING TECHNIQUE
Galleys require additional precautions because they have drains and sills around
the outside periphery. The dams collect the water and other fluids and direct
them towards the drains, which are ported overboard instead of allowing fluid to
collect on the floor structure.
The most effective means of corrosion control is to prevent the liquid getting to the
floor in the first place. The vacuum flush system is a great improvement over the
re-usable water system, and the under-floor structure on these aircraft is in much
better condition.
On all toilet systems it i s important that leaks are detected and rectified early.
Often the first sign that there is trouble under the toilets is water coming from the
lower bilge drains on the underside of the fuselage. Any liquid from these needs
immediate investigation. Remember, liquid coming from the bilge drain could be
(a)clean water (b) liquid from some cargo on board, or (c) toilet water. The clean
water could be rain water, condensation water or potable water. In all cases the
source will have to be found and the fault rectified.
GALLEYS
Galleys are used for the storage,:heating arid the preparation :of food. Drinks are
also prepared and kitchen rubbish stored. Galleys may be fitded d the back of the
aircraft or, on larger aircraft a t centre locations. Figures 3 1 ahd 32 show typical
galleys including service trolleys. (Trolleys are considered a s p a t of the aircraft for
certification purposes and are your responsibility - as are the ghleys and all
electrical appliances there-in).
- 38 -
moodull l A-1482
ACCESS TO SWITCH PANEL BACK CONTROL PANEL
GALLEY WASTE
CONTAINERS
WASTE BAG
ACCESS PANEL
- -
RETAINING BAR
Galleys are located onto and bolted down to the seat tracks, in a manner not
dissimilar to seats. Figure 33 shows an example of the attachment. In addition, tie
rods are attached between the top of the galley and the aircraft fuselage structure.
Galleys use a considerable amount of electric power, and have their own feeder
circuits that will be load-shed automatically in times of high current demand.
Galley power may come direct from the secondary aircraft busses or be provided
through Electric Load Control Units, ELCU7s.These units measure the current
being drawn by the galleys and prevent overload. They also act as a switch to
remove the power to the whole galley complex should aircraft power consumption
become high.
Galleys usually have an electric distribution panel accessible from the front of tl
galley that allows for individual isolation
-- - of;ovens etc by C / B actiK. This panel
1
often h a s a light to indicate that power to the galley is on.
\
I
All systems in a particular galley have control switches and these are normally
located close to the galley. Often there will be a master isolation switch for both
electric supply and water.
Galley Chiller Unit
The lower cupboards in the galleys are used for storing food prior to it being
heated. They are usually cooled by a chiller unit. Figure 34 shows the location of a
typical under galley chiller unit and its associated ducting. Note that the ducting
circulates the air from and to the cold cupboards (chiller cabinets) in the galley.
Note also that the drawing shows one VCCP removed.
The fan motor and compressor motor are both switched on from the galley control
panel. The fan motor drives two fans, one draws air from the cold cupboards, and
after cooling, passes it back to the cold cupboards in the galley. The other draws
in ambient air to act as a heat sink for the condenser (cools the condenser), it is
I - -
thenpdiscljarged overboard. -
I
I
I /
l 1~1 I
I '
L
UPPER CHILLER
FILTER 8 CONDENSER
MOISTURE
DRAIN LINES
- 41 -
rnoodull l A-1485
Chiller air is drawn across the evaporator and cooled by heat transfer to the
refrigerant (Freon or similar) and passed back through the ducting to the cold
cupboards.
The VCCP relies on the principle that as the refrigerant changes state from a
liquid to a gas it absorbs heat (from the chiller air). The refrigerant is pumped
around the system (as shown) by an electrically driven compressor and enters the
condenser as a super heated gas. In this condition it is ready to give u p its heat to
the cooler ambient air. The liquid Freon leaves the condenser a s a liquid and is
passed to the evaporator via the expansion valve (sometimes called a temperature
transfer valve). This valve is controlled automatically by sensing bulbs down
stream of the evaporator.
At the expansion valve the refrigerant is allowed to expand and is made ready to
absorb heat from any warmer medium. At the evaporator it absorbs heat from the
air and becomes heated and turns into a gas. The Freon gas now passes through
the temperature control sensor and back to the compressor, this compresses thr
gas increasing its heat still further- and turning it into a superheated gas. From
-
here the refrigerant passes to the condenser and the cycle continues.
The compressor serves two functions: To pump the refrigerant around the system
and to compress the refrigerant raising its temperature and incieasing the
1 -
efficiency of the condenser. 1 . -
\
A programmable timer operates the VCCP in 10 minute cycles. If at the end of the
cycle the temperature of the refrigerant is less than 26°F (-3°C)then automatic
defrost is initiated - this involves the fan being shut down and the hot gas by-pa,
valve being opened. Defrost stops when the temperature reaches 4°C.
Some chillers may be shut down when the cargo fire extinguisher system is
armed.
i E - - D \CHILLED RETURN AIR
FROM CHILLER
CABINETS $$,,~~~ CABINETS
To help reduce the noise levels from chillers they are usually mounted on anti-
vibration mounts.
Maintenance of the chiller unit is confined to checking for security, leaks, damage
and correct contents level - also functional checks.
- 43 -
rnoodull l A-1487
If recharging is required it is important that no air or liquid other than refrigerant
is introduced into the system. Often units are 'sealed for life'. The ducting requires
care during maintenance to ensure it doesn't become contaminated.
Galley ovens may be single or double ovens and include a fan (usually),a control
panel arid a door fitted with a seal. The seal can get damaged and care needs to be
taken during inspection to ensure that it is serviceable. Ovens are periodically
tested using a thermometer to check that the selected temperature is achieved.
Care needs to be exercised during this function to ensure the electrical supply
system is not overloaded - also beware of the burn risk on hot surfaces.
The oven control panel is usually a separate unit with an ON/OFF switch, lamp
indication and a three position selector - fan only - high temp setting (350°F)an
low temperature setting (300°F),and- atimer - up to 60 minutes.-
-
- -
Some geleys have a Trash Compactor. This is a large press tdat squashes the
trash to reduce its volume. They need regular:cleaning. If this i$ not fitted the
galley will have a simple bin arrangement that has a hinged top access panel.
Beverage makers are installed to brew hot drinks. These are electrically powered,
with a supply of potable water. There are lights on the front that indicate low
water and system ON and in use. These units are slid in from the front and have
rear connectors. This makes changing easy but can lead to water leakage from the
aft water push-in connection, particularly when the water pressure is low.
On twin deck aircraft a galley lift may be fitted to allow the carts (service trolleys)
to be loaded on the lower deck and transported to the upper deck galley.
Currently the B747 is the only twin deck aircraft, but the system could be fitted to
aircraft coming into service such the Airbus A380.
On the B747 the lift is driven by two motors that drive a vertical screw jack. The
lift is attached to this by way of a ball nut assembly that allows the lift to be
lowered and raised between floors. Micro-switches prevent the lift from moving
unless the doors are closed. Mechanical locks will prevent the access door to the
lift shaft from being opened unless the lift is in front of it.
SAGINAW BALL
SCREW ASSEMBLY ROLLER
CARRIAGE
ASSEMBLY
I '
1 1
Fig. 3dI ~_ Y -P I C P ; L ~ / ~ A L L ELIFT
1'
Y 1
I - /
I -- \
\
EXERCISES
1. What can drinking water tanks be made from and where are they
located?
2. What is significant about the fixtures of a drinking water tank?
3. What does the light on the sink water heater go out for?
4. How is drinking water cooled?
5. How are the contents of the potable water tank indicated?
6. Where is the contents information displayed?
When are drain masts heated?
What is a gray line water valve - what does it try to overcome?
Try spending some time looking a t the water system of your aircraft (if
it has one, and if you have access). Locate the tanks and note the
fixtures. Locate the rest of the components and check on their
positions in the system and attachments to the structure. Spend a
little time looking through ATA chapter 38.
Describe how to ramp service the re-usable liquid flush type toilet.
How is the flush cycle controlled during the flush cycle of a clean
water type toilet?
~ e s c r i b da basic toilet vacuum system.
What are the main advantages of this system?
What is the anti-syphon valve for?
What valves are located on the toilet bowl assembly?
Spend some time loohng at toilets and toilet systems (ifyou can). Use
the AMM to check the location of the various components and check
on the maintenance that is carried out.
What material is normally used for floors under tGilets?
How are under toilet floor-phels fitted? I
How does CPF work and where is it applied? I
Read the AMM for your aircraft and look into the method used to
install and seal floor panels.
What equipment might be fitted to a galley? I-
ANSWERS TO SAQs
SAQ 1. A detailed inspection requires good access, with good lighting and the
possible use of other equipment such a s a magnifying glass etc. You would almo-+
certainly require the tank to be removed. (Read AN 3 if you are unsure of your
responsibilities). Removal and fitment of the tank should include the following:
It is important that you study the style, content, and the logical pattern of the
-. this sort of detail in any
answer. The CAA would e x p e c t j ~ utqgive - essay answer.
--
C _ r d _ \
-
-
7 -
S A Q 21.Isolate the motor by tripping the appropriate C/B (arid tagging). Check the
motor and the wiring for any sidn? of overheating - change wiring and/or motor if
found. Ifi the motor has overheated then tlje thermal protectionl device that is
d e s i d e d to prevent this (a mandatory fitrheht - ANs) has failkd. If it is not part of
manufacturer.
--
the mbtor then it must be changedralso add a report made td theaircraft
l 1 \ I -- ,
', I I
'i ' I
Check t i e troub,le shooting section of the AMM. The most logical fault is likely to
be t h e timer logic' unit which shbdld be changed and the systeA tested. Record all
the wdrk\don6"qd sign the CR-S. - ' /
- / -
--- -- -
I- -. _-, !
SAQ 3 . Check if the tanks are full. If they are the system will not allow the toilets
to work. They should not be full as the aircraft has just departed and someone
has not done their job right - but drain the tanks and check the system.
If the job looks like being a big one the passengers will have to de-plane.
If the tanks are empty check the fault finding section of the AMM. Check to see if
any of the toilets are working, if non are it may well be a power supply problem.
The rest of the aircraft systems should be working otherwise the crew would have
reported them a s a fault also, so the main bus bar supply should be OK.
If no electric power to the toilet system fault check the electrical supply system -
visual first - check C/Bs or fuses - continuity check or voltage output check -
functional etc. Significantly more detail would be required here ifit were an
electrical question - and for this you should refer to module 3 and the books in this
series on electrical systems.
- 47 -
moodull l A-1491
If only the toilets to one tank a r e not working you should check t h a t power is
available to that toilet system (similar to above). Check the level sensors (These
may need cleaning - by flushing/servicing the toilet system. If the toilet works but
there is no suction check the vacuum blower C/B's. If they have tripped check the
reasons why, rectify the cause, reset C/Bs and retest. If a n electrical fault rectify
as above. If C/Bs and elect system OK change blower and retest.
If a n y valves fail to work (flush valve, rinse valve etc) check the electrical supply
a n d appropriate valve as above. If supplies and switching are OK change the
valve.
SAQ 4. All appropriate C/Bs should be pulled and 'gagged' to ensure that they are
not reset whilst work is going on. Also, operate maintenance 'break-outs' to de-
clutch the motors to prevent inadvertent movement. Take care, lifts move fast a n d
can be dangerous.
- I
r -- - -
\
I I
1
I
1 I
1 i I
I
>>>>>>>>~>,l>l>>t,;> I !
' 1
/'
- -- I - - ,
Ii
I -- -'
I 1
- -
CONTENTS
Page
Basic principles
BITE
Central Maintenance Computer - introduction
Fault finding
Central Maintenance Computer
Flight phase logic
FDEs
Fault correlation
Fault history -
- . -
Printing I -
Condition monitoring - - -
\
ACARSl link \
\
DFD R facility I ,
,
Maintenance pages
On-board manual systems ,
Answers tb-self assessment questions -
Glossmf tcms - -
rnoodull l A-I493
BASIC PRINCIPLES
Clomputers are used extensively on all systems on modem aircraft. Almost all
electro-mechanical and electronic systems will have some form of microprocessor
control/monitoring unit and this will be connected to the Central Maintenance
Computer (CMC) - figure 1.
We are not going to cover the function of these computers here as this is dealt
wlth in the books on Digital Technology in the LBP series module 5 EASA66.
However, we are going to look a t the operation of the system as a whole including
how the various systems interface with the CMC a n d how the ground crew and
flight crew use it to indicate the fault status of the aircraft.
I t might be a good idea, if you have already studied module 5, to have another
look a t it - j u s t to refresh your memory as to how a computer works. If you have
( not studied module 5 yet you should-be-able to complete this book anyway, but
would'need to read certain sections more thqn once. -
I
-
I \ I
1 I
To help i n your studies I have inclAded a glos,saryof terms a t the back of t h e
book. This should be used as reference. i
' I ,
I
! I
1
1
- - _,
Built-In Test Equipment (BITE)-
-- - -- - -
It will do this after taking inputs from other computers - air data, engine data,
altitude, the PCU itself etc - and processing ("working on") that data.
From this there is a basis for system monitoring. If the inputs are monitored and
measured and the outputs are checked that they are within limits then we have,
essentially, a BITE system.
- 1 -
moodull lA-1494
BITE can come in one of three forms:
* Startup.
* Interruptive.
* Continuous (called Cyclic on some systems).
Start u p BITE is limited in its ability to detect failures resident in the system. A t
power-up BITE will check the power supplies are good, looking for correct phase
rotation, frequency and voltage.
It will carry out checks of the processors and the areas of RAM in the computer,
ensuring all are clear and functioning properly. It will then, through its Built In
Operating System (BIOS) invoke the loading of the main operating software and
any airline modifiable software. This process is very similar to the 'boot up'
sequence of a personal computer.
Intequptive BITE, is something the engineer (or the pilot in some cases) can
initiate. In its simplest form it is a press-to-test, but with on-board maintenance
systems it is usually much more. Generally what happens is the inputs and
outputs bf the computer are electronically (ie, not physically) ,disconnected. The
BITE now starts to systematically inject a signal into each channel or lane and
look for fhe corresponding outpGt.
I I
I t will injLct signals across the entire design range of the system, with generally,
these e$reme functions never being met with in normal operations. Sometimes
this foiTn of BITE is called Ground Tests and we shall look later on how this is
initiated!
--
SAQ 1
Considering what happens during interuptive BITE what precautions might you and
the designer take before initiating such tests?
Continuous BITE, as the name implies, is carried out all the time. Inside the Line
Replacement Unit (LRU), which in this case is the computer, there are (at least)
two channels that work out the information and provide outputs. These two
channels are called Command and Monitor. (If there are three channels the third
is called Standby).
All channels receive the input signals and calculate the output solution. The
command channel will output the signal and send it onto the unit being operated
(whatever that is), the monitor channel will use its output figure to cross-check
that the command channel is functioning correctly.
Brief History of BITE (for information only - not in the CAA syllabus)
The BITE was a microprocessor that provided input and output monitoring.
Access to the LRU was required to initiation the BITE (by pressing the test
button). Typically LED's would come on to indicate system faults. These LED
status indication data would be cross referred to the maintenance manual that
would give suggestions as to the fault.
I n time, the BITE box was incorporated inside the LRU it was testing but initiation
was carried out in the same way. Continuous faults would be shown on the front
of the LRU by looking for illuminated LED's.
i -
-- -
- -- .
A further development came when the-LED'S were moved down to a centralised
location, bften close to the re-fudlidg panel. A bank of LED's &as available for
checking with the aircraft on the ground. As the BITE picked ufi failures it sent a
20
signal illuminate the LED. 1 , I
/
1 , I
I- -
As you may know computers car) startto wbrk for no apparer?t reason, in much
the samelway a s they fail - without warning.'so in this case the LED &uld go out
and the kaintenance engineer would have no ,indication that Ianything I had ever
gone wrong. ~ h i ~ ' ; l a c e dthe enginLer in the situation where hjelshe would have to
change1 items 'on spec' without a sure indication that the item was actually faulty.
Not a-very-acceptable approach to good-maintenance practice:
- -- - -- /
, , -
What the designers did to help to overcome this problem, was to allow the LEDs to
stay illuminated, until they were reset manually. What would happen now is; the
aircraft lands and the engineer checks the maintenance panel noting all
illuminated LED's. The reset button is now pressed and the LEDs that remain
illuminated are noted. Appropriated rectification action would be taken in
accordance with the AMM, the work signed for and all remaining illuminated
LEDs cleared.
* Hard Failure - where the fault is still apparent (ie LED still illuminated after
reset is pressed).
This gave the engineer a better indication of faults that had perhaps cleared but
would still provide a good chance of accurate fault diagnosis.
-3-
rnoodull I A-1496
SAQ 2
Why might a fault not be apparent to the engineers, but the flight crew constantly
complain about the defect? How do you think BITE might help u s detect this?
The final steps in BITE technology (so far) came when the BITE box was moved to
a central location. In fact, the box actually becarne a computer in its own right,
and Boeing call this computer The Central Maintenance Computer (CMC).It forms
the basis for all on-board maintenance systems and its introduction h a s given rise
to a new ATA chapter being formed - ATA 45.
Airbus (and other manufacturers) have the same philosophy but call the unit the
Centralised Fault Display System (CFDS).
Access to tests and checks are now via a centralised menu and can even be
controlled by a 'windows' style software package that is very similar to any other
com$ter. W e shall spend some,time discussing this type of system.
I
I
Figure 1 gives details of a basic system. Note the two way flow of information from
all the lother computers to the CMC with this data being converted into graphical
symbols for transmission to the CRTs (or flat panel displays) on the flight deck.
(CRT = Cathode Ray Tube.)
- .. -
Aircraft system
0 0n~ 0 0
Display system
-4-
rnoodull l A-I497
The Graphics Generator (may be called a Symbol Generator) has stored
infonnation on the symbols to be used on the flight deck displays. It takes the
electronic signals from the CMC and generates the appropriate syrnbol for the
display system.
APU.
autoflight system.
Doors.
ECS.
Electrical system.
Engines.
Fire protection systems
Flight controls.
Fuel systems.
IceIrain protection-systems._
* , - Indicatinglrecording systems. " -
* Landing gear. \
\
1
1 1
* I Navigation systems. I I
*I , ;
I '
I
Pneumatics. ) I
/ ,
I
The aircrkft system computers afe ico~tinubvsly working and cah-ying out
calculatidns as defined by their lodded soi'twhre. Each cornputer-knowd what the
inputs and outputs should be and these are continuously monitored. If any
paramiter goes outside of limits ki message is bent to the CMg, through a serial
data highlway.The CMC will now start to do many things ie:
\- / , i
* It checks-the reported fault against-known criteria. It interrhgates the faulty
LRU.
* It checks the fault is in a 'reportable period' (more of that later).
* It checks another failed unit is not causing the reported fault. For example,
if the IRS failed this would show hundreds of faults in all the systems that
use attitude data from the IRS.
* Providing all this defect correlation is correct, it will indicate the failure to
the flight deck in a number of ways.
* It will store the infonnation in data banks (called fault history) for later (long
term) analysis.
Status Message. (A & B). Is a message that is placed on a status display screen. A
status message gives the engineers a true indication of system failure. Aircrews do
not have immediate access to the status page, but would look at it when 'cued' to
do so. For an aircraft to be dispatched (ready for flight) there should be no status
messages (or a pretty good reason for having one).
- c
3 -
rnoodull lA-1498
Maintenance Message. (B).A maintenance message is set by the CMC after it
establishes that a fault does exist. It takes the form XX-YYYYY. XX' indicates the
ATA chapter that it relates to, eg 27- flying controls. This message is never
displayed to the aircrew a s it is only ground engineers that use the information -
we shall discuss how, shortly.
Fault Codes. (A & B). A fault code is very similar to the maintenance message. It
is set by the failed LRU and the CMC will go through the process of correlating it
all together. As with maintenance messages this information is not available to
aircrew, a s it is only engineers that need it for fault diagnosis reasons.
Maintenance Memo. (A). Airbus use the term Fault Message. A maintenance
memo would be set if the failure is very insignificant, and there was sufficient
back-up to mean the failure could almost be ignored. Here, the aircraft can fly on
quite safely until its next scheduled maintenance when all these minor defects
can be rectified. This keeps maintenance costs down yet does not compromise
safety;-
\
Memo Message. (A & B). You might hear reference to this, although it is not
strictly related to the CMC. A memo message is displayed for the aircrew to see
and it gives them reminders of systems that are in operation eg APU running,
Park Brake Set etc.
For fault finding reasons, they afe of no use to maintenance engineers, but you
may hear them referred to. Obviously the engineer would use them a t the
appropriate time eg, when setting the parking brake.
~ a u fI?inding
t - The Digital Way-
Access to the CMC is provided in a number of ways, the most common currently
is through the flight deck Central Display Unit (CDU).The Line Select Keys (LSKs)
are used to input requests for information. In this system (which is common to
airbus and early Boeing) the requested information is displayed on the multi-
function displays that normally display flight information.
(The most modern system uses a separate screen in the flight deck and requests
for information are by way of a Windows style menus. Display then being given on
the same screen. This type of system is fitted to the B777 and uses fibre optic
interfaces .)
The CMC will display the fault code and also the maintenance message, and these
will be correlated to a Flight Deck Effect (FDE). So the first indication that there i s
a problem will probably come from the crew - either verbally or recorded in the
sector record page of the Tech Log. That will give you the engineer a FDE to work
from. You can now check the CMC present leg faults pages and find the
appropriate maintenance message.
1
--- , Fig. 2 -FIM CHA*ER
-__ --' SUEUECTS '
-1
Tlne engineer takes these numbers to the Fault Isolation Manual (FIM) (an
essential tool in today's integrated aircraft and supporting systems design).
Sometimes a fault in one system will show itself as a failure in another system
and this type of 'fault hiding' can render traditional fault diagnosis techniques
useless.
(The FIM is not very well excepted by the older generation of engineers and some
see it as taking the skill out ofthe job. It is important that all engineers use ALL the
tools that are available a n d the FIM is just that, a tool.)
The FIM is split into ATA chapters. Figure 2 shows the breakdown of a typical
chapter, in this case ATA2 1, which is air conditioning.
21- Fault Codes Index, i s the numerical index of all the possible fault codes. Fault
codes, as you might recall, are set by the failing LRU and correlated by the CMC.
rnoodull l A-1500
2 1-Maint Msg Index, is the numerical index of the maintenance messages that the
CMC sent. The CMC sent these in response to the failing LRU's 'cry for help'.
From the interrogation of the CMC pages on the aircraft you will certainly have
one, and possibly both of these numbers. Figure 3 shows what these index are
like once opened. Mere we are assuming that we have the fault code and one of
the maintenance messages that are displayed. Notice the FIM tasks in the right
hand column.
With reference to figure 2 you will see the other two sections of ATA2 1 were FIM
tasks and task support. The FIM task is the actions you would take given a
specific maintenance message. These tasks lead you through a 'most likely' fault
finding approach; figure 4 shows you an example of a FIM task.
I
I
FAULT CODE
213 147 42
I
FAULT JDESCRIPTION
I
PRESS R E L I E F ' V L V R
,
I
MAINT MESSAGE
21-01 391
I
GO TO FIM TASK
1 I
blank
-8-
rnoodull l A-1501
T A S K N U M B E R AND A. fbln t.~k 1 s l o r ..lnl.n.nr. ..m..p.: l?-IZW.
DESCRIPTION B. ,"l,t., cr.,u.r,rn
<I) I 1 Ih. M r .~DII I ( I I I 5 r l l h Ih. .#lnlen$n(. ..s%ap.. I h n , O Ih.
V ~ u l tI . o l . l l a Vcorc&. brlw.
MAINTENANCE MESSAGE <I> 8 , a h . -1 .h-. LIT'Nl* r # % b Lh. m.1nl.n.n~. ..s.mp., Iln & tL.
Iz-Pr<.,ry Illp,.,<a
4l.h. I~,un*o.\lla Ir.".e.,
,.,I a ,L.
13)
,r.o,bn...
Bs a chack f w Vb<
( I > I f % h a r e 1% I I U b.iu.n
"I?I,I.
.Ins
,
oh# 8 d e t c-ct- 8*7t36.
.nd 9 a# W 1 1 Y . do lllil charkt
*
(.> nalw. ch. r.slsr.n.as
< a c t o r m th.
I ) PI" 1 I. 01"
bet--
,..%"
*, ...
,he*. o.1.m
trmrdi..,,
.~itll.l
of ~ l n n01 th.
"zltl':
21 ? I n I ~s .in 6 . 1 w l l 1 . d r.lltlulc.
,I PI" I 9 . ,P..Ll,,dr..l.l.r.c.
1.l.n.. I.-- oh..
(<-m &a
cr-,, oh..
Ib) I , th. r..l.l.nc. 13 ml In Ib. ~1.0. 1mc0ll.d f o r .arb p l l r
01 D l n l , r . o l l ~ # ih. l e f t I cot- m.lilcn tr.nsb.r.r, 1111114
1.m 2,-,!.0'~40l~.
It1 I 1 th. re%l.lmnca 1 1 In the r m g . % o l r l O e dI- .arb o.lr o l
olns, & t h i s 'ha&:
I ) W n 1h.s. clrrull br..L.r. m lh. I e I I Plr. m < l O l :
.I I, .c< m
61 LJ .I, *r*
I, 41 ILPs* P I "
d) AT LL<Y sCU
1 ZI
I)
p,
L)
..u~.
11
8Z
B'
86
81
srls ,111
I l l i O f s l B s l (L, .)
E L ~ Yr c x l <
.UO 11111 L C I I I L I
th. 1.1, I ME, a u z l 1.0. t h CI-5 . b a i t .
Jl 10 I c m l l w l t lchert b.8n.n ,la,. vlnl 01 c a r t o r
n U 7 $ > <8 , t k E l - 5 z h c l l n r d c-c<or b4'7'J a t th. t l - S
.h*I, <"t" ?r-,,-t,,:
W7IS' o'LT11
---~- ~ ~- ~
p'n, -..--.--.--.------rln ,2
W I R I N G CHECK .I" r ---- -- ~
* --1; 10
i
,.-
,, I r ) T G - , l y
.I,,
,
.
,
At-
,
I" ~ h driq,
a
.I" I,
L th.,.
' _ --
-- - -'
i
,/
, ,
JY
Paw 207
15/95 ~
I
!
1
,
i
I , ,
, I I , -
i
4
:
~ -- - \\ ; '
,
1 '
8 ,
i
' !
,
'\
,
:
I
,
I j ;
Finally thkre is, sometimes task support data,, that provides wiring diagrams and
locations of-components. This section is not,always available, however.
I -- - : - 1
To recap on the sequence of events:
I ,
Figure 1 kave details of how the fault information is passed from the user systems
to the CMC a n d on to t h e output device. So far we have not explained much of the
detailsiof this process.
SAQ 3 :
Consider for a moment when we will NOT want to report defect informationj7om the
CMC for onwards display and subsequent storage in the fault history?
From SAQ 3 we should start to see the requirement for a couple of parameters t o
be set. We need to have 'phases' of the flight so that we can work out when to
filter out maintenance induced faults. Secondly we need some way of identifying
when faults happened previously. These are called Flight Phase Logic and Flight
Leg Logic.
- 10-
rnoodull l A-1503
Climb
Cruise
Descent
Approach
Landing
Taxi in
Engine shut down
Maintenance
The CMC is receiving infomation from every system on the aircraft so can work
out which phase it is in.
At power-up the CMC resets and puts itself into the first phase. It now waits for
the engine start signal from the Electronic Engine Control - EEC (the digital device
that controls the engine). When it receives this signal the CMC moves into the
next phase.
- -- - -
I - - -
I I
' ! ' 1
Take off phase is set when take-dff power i; selected.
1 I
1 , ,
I \ \ I - -
Climb dhase is set-by a combinatioh of FMC dnd time delay fiP& take-off.
I i I
Cruise is given by a combination06 the FM,C $nd the IRS gividg stable attitude for
a set period;
--
- _ I %
-
-- -- . - 1- -- A
I
Taxiing is given after the thrust reversers are set from reverse to forward thmst
arid idle power has been selected for a period of time.
Engine shut-down is given when the run/cut off switches are set to off.
Each phase change requires the previous phase to have been set before moving
or1.
The 'odd ball' phase is maintenance, which is a phase that ground engineers can
in'duce before any specific functions are carried out. The CMC will consider what
flight phase the aircraft is in before it signals a defect. This is called flight phase
screening.
Basically, any defects that occur in the flight phase will be recorded and hence
stored in the fault history. Faults occurring outside the flight phase are displayed
as existing faults only.
rnoodull l A-1504
This means that all the faults 'we' induce on the ground do not clog u p the fault
history. This keeps the fault history for real defects not maintenance induced
defects (such as removing a component for replacement).
FDE's
Flight Deck Effects (FDE's) are any effect that is noticeable on the flight deck.
Certainly the 'Status' messages that we have spoken of will be FDEs. But also
missing flags or failure bars on primary flight displays are also FDEs.
Fault Correlation
MESSAGES
DISPLAYS
REPORTS
- 12 -
rnoodull l A-1505
Input
- Processing. All the aircraft systems send information to the CMC and it
arrives a t the input processor. Input processing will interrogate the failing LRU
alnd possibly initiate BITE checks. It will check the information that it is receiving
i:s correct, valid and accurate.
Input processing works a t very high rates (typically processing u p to 5,000 faults
per second and receiving about 5 times that number). Providing the faults are
accurate, the messages are passed onto the next sub-routine.
Inhibits
- and Special case BITE. When the aircraft is powered for the first time or
starts an engine, we would expect many failures to happen. We don't really want
to be processing all of these a s we know they happen every time so this sub-
routine filters these failures out. It also removes failures caused when the engtnes
are shutdown or power is removed from the aircraft.
Cascaded Effects. If a key LRU were to fail, for example the IRS. The IRS provides
-
irlforrnation to virtually all systems-on-the-aircraft and if the IRS failed, it would
induce Inany failures in the other user-systems. These failureg would be reported
to the CMC but this sub-routine would detect the cause and ?e$son for the failure
a n d filtkr them out. I I I I
I I 1
,' '
Consolidation. Often several maintenance messages will be generated when
-
sorneth;ng fails. This sub-routink brings thkse related failured tbgether., It is not
like cadcaded effects, which was about remoriing faults that were caudd by other
failures. This is grouping together similar faults. ' I
1 1
I I
NOTE: Airbus tend to use this style of categorisation, Boeing tend to simplqy
matters and state that all defects must be referred to the MEL and the MELprovides
the categorisation. In this type of system the ground engineer doesn't even see the
minor defects. Each system has its advantages and disadvantages. You need to
become familiar with your aircraft, so check on how it works and compare with
these notes.
If this sub-routine is unable to correlate for some reason, it will still allow the
failure to be displayed and stored (if appropriate) but now it is u p to the engineer
to try to establish any link.
- 1 3
LLJ -
moodull l A-1506
Storage and Display. This is the sub-routine that uses the flight phase
information and decides if a fault is in a reportable phase or not. If it is in a
reportable phase it will move the fault into the fault history and usually displays it
in a section called present leg fault (sometimes termed inbound faults).
Present leg faults records ALL faults that have happened on this flight leg in the
reportable flight phases. This would include active (hard) and latched (soft) faults
that have and have not been correlated together with a FDE. If a fault reaches this
sub-routine and has not occurred in the reportable phases it will not go into the
fault history, it will not be displayed in present leg faults, instead it will be
displayed in existing faults for a s long as it stays active (hard).
A s soon as the fault clears it will be removed. From that you should be able to say
that 'existing faults' displays real time information. This makes existing faults
very useful for u s as maintenance engneers when we are about to dispatch an
aircraft. Using this we can see exactly the failures the aircraft has.
-
\ -
The fault history will store all defects that have occurred in the reportable phases
(the flighlt regon) and will keep them for future analysis.
I
--
I '
You sYould remember from your Air Legislation studies, that we have to keep all
aircraft iecords and part of that is to keep a 'reasonable' amount of history on-
board ithe aircraft - often as part of the Tech Log. That information is sometimes
invaluable to engineering when trying to locate defects that have only occurred in
the air. It is also a useful tool for spotting a trend of failure, leading u s to a more
correctfault diagnosis first time. -
Much in the same way as engneers look through the aircraft Logbook for the past
ten or so sectors, we have the same ability with the electronic information that the
CMC has been collecting.
All fault codes and maintenance messages are stored in a memory that is volatile
ie, it is lost when power is removed. That would be true, but for the fact that we
supply a 28vdc supply direct from the aircraft battery. This supply will keep the
memory of the fault history alive for usually about two weeks.
SAQ 4
What is the process for replacing an aircraft main battery? How might that now
need modvying in the light of what you have just read?
- 14 -
rnoodull l A-I507
In addition to the change of battery procedures, we must also consider long term
parking of the aircraft and hangar maintenance. Long-term parking will drain the
battery so we must record the fault history a s part of our preparation for p a r h n g
atnd/or storage routine.
Hangar maintenance will cause all sorts of faults to be recorded in the fault
history for various reasons. Again we need to record the fault history prior to
starting in-depth hangar work.
We use the fault history information for fault analysis and to provide assistance
when fault finding. The information is displayed, as it was when it first happened.
Figures 6 and 7 give two examples, but this information changes from aircraft to
aircraft so there is no need to study them in detail.
blank
l rO;
- L -
moodull l A-1508
You m u s t have completed an approved course on the aircraft type before you a r e
given authorisation a n d EASA PT 66 endorsement (to sign for work done), but in
general it is worth noting t h a t the pages all show:
* Date and time of event.
* Flight leg or legs (see below).
* Fault code.
* Maintenance message number (including ATA reference).
* Short description of fault.
* Possibly flight phase on later systems.
* Possibly type of failure ie, hard (active) or soft (latched).
1
EXTENDED OTHER
HELP REPORT TAIL I D
RAINTENANCE FUNCTION$
~77701 TIME/DATE
The t i m e 7s OlLSr OBJUL97 )/{SOURCE FIELD
T h i s d a t a Is from L e f t CMCF
S e l e c t t e x t o f a leg, then s e l e c t t h e INSTRUCTIONS F I E L D
FAULT SuMblARY NALNTENAHCE MESSAGE DATA b u - n to g e t more data.
t t o-
FIELD T I T L E 1
'21 c a b i n Temperature C o n t r o l System (51- NUMBER OF ITEMS
MAINTENANCE J t m l n t m a n c e messap. 21-22101
' MESSAGE NUMBER'' lare A i r 1smper.tura Snar 1 (FUght Deck) * I p s ( i,
I
out of rang. -, FAULT SUMMARY
MAINTENANCE This f a u l t has occurrrd in the foltouing Legs:. /'/ GROUP
4 y
MESSAGE SYMPTOM ~ L ~J e g u Approach I l?rsr f ~ntarmittent ( 1 ) )
I LJ ~ b g
[I Leg 31
--
I XOLLOUI
Cruiaa
I L ~ ' I IUOJIJLY~
05261 OSJW97
nara
I n t c r m i t t e n l (14)
2
H e i n t ~ n a n s rflc*sage 21-29434.
cabin Tenprratura c o n t r o l l r r ( R ChanZ) ha8 no FA',ULT OCCURRENCE
{rput f r a A i r Supply Cabin Presourr c o n t r o l l e r (R) on
I=]}-/? System A R I l l C 629 Bus ( l q f t ,
When considering fault history it is always useful to know when the fault
occurred. For example - the crew reports problems with 'the aircraft flying with
constant rudder trim'. We carry out the interuptive BITE check and this reveals
nothing - what then? Well, we could check the fault history a n d could find that
this problem h a s occurred on the last, say, ten flight sectors.
- 16 -
rnoodull l A-1509
A check of the maintenance records might reveal that one of the flight computers
was changed after that flight for some other reason. We have used the information
in the fault history to accurately analyse a fault that we otherwise could not trace.
'We can now see that there is a use for fault history. We now need to understand
:how the flight legs are defined. This is done electronically. First of all, what is a
flight leg? A flight leg is a sector, (that is: doors closed, engines started and
aircraft airborne). The flight leg ends when the crew shut-down the engines after
].anding.
All those parameters are sent to the CMC and the CMC then calculates the flight
leg. Figure 8 shows the flight leg logic for the Boeing 777. Similar logic is used on
other aircraft.
- -- -
'
-
-
--, -
--
\
-
r - .
I
NEXT FLIGHT LEG
' TOBEGIN,WHEN 1
@5 ION
I ,
PARKING BRAKE RELEASED
' 0--
1
T E = TRANSITION
ENABLE
I @ =;:T;:s;
MANUAL-LEG INHIBIT
-
-
The aircraft's computers count backwards so the current sector i s flight leg zero,
the one before that is - 0 1, then - 02 and so on.
Looking a t the flight leg transistion logic, with the aircraft on the ground and the
engine started a new flight leg is started. As the flight leg is started notice that an
input is provided to the bi-stable RSQ, that prevents the next transition by
removing the logic 1 from the AND gate.
To regain the Enable logic 1, the aircraft has to take-off (park brake released AND
e:ngine at take-off thrust AND groundspeed of 80kts). This provides an input to
the 'S' leg of the bi-stable and then resets the enable logic.
That concludes this section on the workings of the CMC. It might be worth having
a re-read of the text a s some of the concepts introduced do make more sense on
the second read.
Most people who have a computer or uses one usually come to the conclusion
that they never quite get to grips with all its intricacies. J u s t as you think you
have mastered a topic then a new program (software)is introduced or you find out
about some additional function that you've never used before. Well, the same
holds true for the CMC.
So far in this book we have just discussed the make-up of the CMC and how we
can use it to fault find. I n fact we use the on-board maintenance system for many
other functions to include:
-
* Printing. !
* Condition monitoring - or ;structural analysis.
* Engine fan blade balancing.
I
* ACARS link.
* DFDR facility.
* Maintenance pages (providing real and snapshot information).
Ground Testing
The CMC can be used for a wide variety of testing duties. The CMC is
programmed with a series of interuptive BITE checks. A system can be selected
for testing and specified interuptive BITE checks carried out.
For this testing to be allowed the aircraft must be on the ground and often
airspeed h a s to be below a certain speed (80 kts). The reason is simply the
interuptive BITE test actually electrically disconnects the inputs and outputs and
then injects a whole series of inputs and monitors for the correct output/s.
Interuptive BITE has the advantage that it will test the system beyond the
'normal' expected range of inputs. It tests the system to its design limits.
- 18-
rnoodull l A-151 1
Ground tests are initiated through the normal CMC interface, which as we've
already discussed is a CDU (using LSK) or a MAT (Maintenance Access Terminal)
using a Windows based menu driven application. Indication of test pass or failure
will be given through the normal screen display. Results can be printed off (more
of this later).
[The MAT terminal of the B777 consists of a screen, tracker ball (same function a s
n mouse), and a select button, with the keyboard stowed within the console. It is
situated on the flight deck-deck just behind the crew.]
u
PMAT
It is true that we had all this when we had intemptive BITE, just by pressing the
button on the box. But now we have distinct advantages:
* All system tests (within the scope of the CMC) start and operate from the
same point.
* Changing the diagnostic software loaded into the CMC can change the tests,
very quickly. (Useful when updated LRU's come along).
I have not included any details of how to initiate ground tests as they vary greatly
between aircraft. It is important to understand the principle, however.
Air/ Ground
- Simulations
-- - -
Many systems use airlground sensing for safety and operational reasons. As
ground ehgineers, when we test thkse systems we need to put the aircraft in the
'air' withhut actually starting the engines. Traditionally this used to be performed
by raisink the aircraft on jacks ok insertingblocks in the WOW (Weight On
Wheels) micro switches, or pulling t h e appropriate C/Bs to the switches to
simulate t h e airborne condition. -
(The WOW micro switches/proximity switches are fitted to thk landing gear shock
absorbers to make/break a circuit when oleo deflection takes place so the aircraft
'knows' when it has taken off or landed. Sometimes called squat switches,
ground/air sensors etc - see the book in this series on Landing Gear.)
As all systems report to the CMC for diagnostic reasons, we can simulate the air
mode from the CMC. From the usual input device (CDU/MAT) we select the
simulation screen. This will prompt u s to check many things such a s we would
normally check before a 'traditional' simulation method; these might include, but
not limited to, the following:
- 20 -
rnoodull l A-1513
The use of this function is usually limited to one of the CMC input devices, called
the master. This is to ensure that there is no inadvertent operation of the
simulation, which could prove expensive, not to mention dangerous. A s a point of
nlote, the CMC master input device has to be out of the "mainstream" flight crew
use. It must not, for example, be a t the CDU that they normally use.
Special Functions
Special functions include a host of various features that, a s ground engineers, can
be useful. The airlground simulation is a form of special function. Special
fu~nctionschange from aircraft to aircraft but can include such tasks as:
* Flying control safety device override. Some flying controls are locked on the
ground for safety reasons, alternate flaps is a specific example. To get these
to operate this function is used.
* Door lock activation. Modem aircraft have flight locks on the passenger
-doors to prevent them from being opened when the aircraft is airborne.
* Airyground target calibration. \ 'i I '
* Proximity sensing device calibration. All proxirnity-sensing devices have a
'range' where they come i n f . ~ / ~ r o x i m i t ~ , ' ( o ~ eUsing
r a t e )this
. type of function
we can set u p exactly whe$ the devi6e hctivates, removing the grey area.
l 1 , --- -
,
\
-- -
The list cbntinues, but you should ibe starti,ng to get the hangof-the principle.
Data Load ,, I ,
I 1
r
\ _- -- -- // -
-1
A data-loading-facility is required for a-number of reasons: - -
Data loading is in fact read or write information, not simply a loading (write)
facility.
Originally data load facility was provided by an external test set that plugged into
a test connection, often on the front of the main aircraft computing system. Data
transfer would then be from/to a magnetic tape in the test set. The set would
convert the magnetic information into coded decimal and often something like
code was used.
Clock Pulse
I 1
Stretched portion of
tape. If no clock pulse
this would indicate 4
logic 1's instead of
the correct 2 logic 1's
This type of data transmission was always transmitted in parallel (see figure
10) to ensure that any stretches of the tape were not seen as logic zero. This
method was cumbersome, slow and required large test equipment.
This method i s still used today on some aircraft but most now use other
systems ,such as the 1.44MB diskette (floppy disk) that we see in use on all PC
s y s t e q s 'today.
1 1
somewhere o n the flight deck (on the MAT terrninal for example), close to the
master CDU (usually the centre one for maintenance reasons) there will be a
data-load facility. 1.44MB diskettes can be loaded into the drive and then
through the normal input of the CMC we can install the data to the correct
location.
This addition provides us with the benefit that we have all the software to hand
on-board should something happen that corrupts a particular program.
(Any one who owns of h a s a lot to do with a computer knows have annoyingly
easy this can happen.)
Prior to loading any software we need to ensure certain parameters are cleared.
Firstly we must satisfy ourselves of the origin of the data and the fact that it is
virus free. We must then check that the software we are about to load is the
correct part number and is compatible with the LRU we are about to load it
into.
- 22 -
rnoodull lA-1515
Finally after load we m u s t ensure that the correct entries are made in the
aircraft log to ensure all data is updated and correct.
Data loads for the other functions are performed in much the same manner.
Fault history can be read and copied from the CMC a n d reloaded again, this is
useful for the reasons we stated when we looked a t fault history. Navigational
d-atabases provide information on the airports and navigational aids worldwide.
You may also see other (minor) information loaded into the CMC in the same
nnanner.
F'rinting
I I - -
The p i n t e r is usdally located on the flighd dLck centre stand. Both flight crew
40
and the kngineers have access it. ~nfonhationis sent to the printer from the
C!MC (NOTE thk diagram shows the ~ 7 7 7 ' l a ~ o uand t on that aircraft the CMC
residzs wTthin AIMS). This i n f o ~ m & t i o n ~ ~ ~comes
u a l l y in ARINCA429 b i n a g
coded decimal form, b u t you Gy see it in other forms also.
Inside the printer the processing board converts the data into the language the
printer uses. This is fed to the interconnection board, which controls the
printing process. At the correct sequence the head moves and is heated, this
passes over thermally sensitive paper, which is moved by a stepper motor.
Defects of the printer are notified by way of lamps on the front of the panel.
The printer normally doesn't fault report to the CMC; it is part of the CMC and
so is not really necessary. Paper rolls are loaded in a number of ways but the
instructions are always located in the AMM arid often on the inside of the
printer top cover. A s the paper is thermally activated it must be kept away from
heat and direct sunlight.
blank
- 23 -
rnoodull lA-1516
r-
SUPPLY
'-)A
- L-r
rnooduil l A-1517
Condition Monitoring - or Structural Analysis
The CMC is already receiving information from all the systems on the aircraft
and the engines are no exception. Various parameters and triggers are set and
this information is collected by the CMC and sent onto the ACMS. The type of
information that the ACMF will take depends on how it is being used but is
likely to include:
* In flight engine shut-down information.
* Filter changes - yes the CMC can work out when an engine filter is
changed by checking a data chip inside it.
* Structural loading (if appropriate).
* Routes flown. - - ---- - --
1
--
I
\
I
This list is by no means cornplete'as virtually any piece of dAta that the CMC
h a s can be requested by the AC'MF,but stofage tends to be a limiting fitctor.
When the ACMF has the data it requires' it will transmit this to an optical
recorder, known as the Quick qcqess Recorder (QAR).A typical 'penny and
Giles7unit is shown in figure 13.Maintenan'ce of this systek ip really limited to
replacing the diseevery ramp c p c k a s spkcified in the AMS (Aircraft
~ a i n t e n d n c e~ c h k d u l e.)
I l 1
/
,
The procedure for replacing the d i s ~ i s i
I-_- - -
,/ dl
- -
Draw a new item from stores, checking its applicability, validity and
stores release documentation. Check also that it is empty.
Wear lint free gloves.
Remove the new disc from the case and hold it carefully.
With aircraft power applied press the eject button and remove the 'used'
disc and place it in the case, in which you have received the new one.
Remove the spare disc and place that in the active slot.
Place the new empty disc in the spare slot.
Remove gloves and label the used disc stating the aircraft serial number,
the date of removal and the reasons why.
Return the disc through the correct channels to the data analysis unit.
Carry out the necessary aircraft documentation.
A s yet, no civil aircraft have fatigue meters and so this data is not requested.
P O W E R ON
,
SPARE DISK
SLOT
INDICATOR-, C PRESS
SPARE DISK
O P T I C A L OAR
PENNY
&
GILES
ACTIVE DISK
/ SLOT (BEHIND
DOOR)
LOW CAPACITY
EJECT BUTTON
M A D E IN
U.K.
Before we finish this topic, I shall cover some functions of the CMC that we can
only describe as bonuses. The system was never designed around these but
they do prove increasingly useful.
- - -
The engine EEC sends information to the CMC through the normal course of a
flight. Engines have vibration motoring systems installed a n d this information
is available to the CMC. The CMC is programmed to check the 'high7points of
the engine acceleration a n d deceleration and from that it can calculate
mathematical where balance weights are needed if required. It is
recommended that you read the gas turbine engine notes and particularly
those relating to engine balancing and instrumentation.
ACARS Link
All the information the CMC has can be transmitted to anywhere in the world
either via VHF or Satellite communication networks. This means that should
the aircraft have a significant failure the aircrew can select this function and
let the ground crew at the receiving station know details of the failure prior to
the aircraft touching down.
-
- %(j
moodull lA-1519
'This means that fault diagnosis can begin and in some cases be completed
prior to aircraft landing. Spares and equipment can also be prepared so
rectification a n d turn-round can be accomplished with minimum disruption of
the flight schedules.
Some software faults c a n be cleared whilst the aircraft is in the air with the
aircrew in communication with engineers on the ground. Several airlines have
Faults Cells manned by engineers around the globe, say one a t LHR and one at
San Francisco, where d a t a on airborne aircraft faults is sent a n d a n y necessary
actions taken.
Actions can include discussions with the aircrew on how to rectify the fault
a n d forward planning c a n be carried out a t the destination airfield re spares
availability, manpower availability etc.
IIFDR Facility
( This is-similar to the ACMF. The Digital-Flight Data Recorder has-to be carried
on allcom&ercial air transport aircraft; it is sometimes referred to as the 'black
box' - though they are usually 6right orange for crash scen6 identification
purposes. They are located a t the back of'the aircraft and have son&-locating
beacons attached to aid undedat'er recovev.
I / II '
The F Q R simply
~ ~ a recording d e v i c ~ t h d k e c o r d sa whole y a y of parameters
like thiottle settings, thrust conkhanded,\flight control positions,-aircraft
attitude, altitudgttc. The A N 0 states thatlit .shall be in use from the beginning
of the t4e-off y n to t h e end ofithe landing run and that thk dperator shall
preserve ht -least the last 25 hours of recokdihg.
-
i - -- /
-
\
J
,
- -
All this information is by defaUE ai&liiGe a t the CMC and itpis %ow a case of
converting the CMC language into BCD language that the recorder
understands. The CMC converts the signal and sends it to the FDR.
Another advantage of this system is that the FDR is now also in direct
communication with t h e CMC and can put u p failure codes to inform the crew
if the FDR is not functioning properly.
hlaintenance Pages
This is not strictly speaking a function of the CMC, but I would suggest that it
does fall into the category of on-board maintenance. The screens in front of the
flight crew are divided u p according to function. The outer two are always
Primary Flight Displays (PFD);the next two in are used normally for
Navigational Display (ND), but are really called multi-function displays.
The two displays in the centre, the top one is the ECAM/EICAS which provides
information regarding the engines, and operating parameters of the aircraft
that the flight crew in particular are interested in.
- 27 -
moodull 1A-1520
The lower screen is another multi-function display that is used for systems
such a s hydraulics, pressurisation, fuel, electrical supplies etc.
,-
All screens are in colour.
I
Chart holder Optional
metric ALT
/ I , Clock \
LDG
GEAR
I
DME / VOR
CTL LVR
DDRMI I
-
Optional ADF RMI
Some of the displays are interchangeable, but the PFD and the EICASIECAM
have their function assigned and cannot be used for anything else. In fact their
importance is such that they will 'steal' another screen automatically should
they fail.
We can call u p a variety of synoptic pages on the systems and figure 15 shows
an example of two displays - one for the hydraulic system a n d the other for the
electrical system. These pages show a diagrammatic representation of the
system with indications of parameters such as pressure, flow, temperature,
voltage, frequency etc as appropriate.
We can also, through the input device to the CMC, call u p maintenance pages
(see figure 16).These give actual values for inputs and outputs to various
systems. These screens can provide a good insight into a system when fault
finding.
HYD
SREEN - BLUE YELLOH
9 Q
- - . \ -
I I
So much so that the CMC hold; a series of trigger values and i f any input
moves beyond the trigger the screen is snapshot. This is stored in memory for
us to view and/or print when the aircraft lands.
I
-
I I /
I I
1
I
UmLLBua nus
l 1
-
_- -- ,
- u1 c I
,
, YES 1 YES YES
L NO NO no
TITLE ULLar PG 211
AUlO AUTO 1074
\ M,U.
Nun NORM HORN
a 12.03 r
-T2\
YES
\
ulmLmun - 3 0
- ID12.03
12.03 n
FAST
YES
I< 12.03
12.03 UP
.or, trrc -0.70 trr nm +2.39 rnnat 2liW rr 12.03 I NO
*OL$ l*~c -0.18 -I 0' t5.23 CII 257 no
10l.y LCC ~1 ~2 L +3.U t3.36 I YES YES
I 1 .!ru..n M.15 '0.15 t0.15 4.15 +13M +ISM YES YES
YES YES
c:trU.L I;a.75 1r +0.75 '
,
- AUTO - ': ".Y
wrlroll I +5.36 +5.57 -0.42 +5.36 tJ.57 4.42
2 G.36 r3.57 4.42 t5.36 +3.5? -3.42
rr n t s t I
3 C5.36 +3.57 +5.36 63.57 rl620
SYSTEM 1-c6 3 +0.05 M.05 rO.05 W.05 P YES UP
DATA ' ,1620 n P YES UP
2 +O.OS rO.05 -1620
IRm
n-r IW 1111 ~4w IIL
M 1
YPI.EUII.
1 7nNA1c4
.WITIDI l l l l 1 - z - l
17 JAN 95 mc 1 8 : 4 4 ?r
rorrlr- l t9.W a.05 UJ.03 nlrl ln +1.2 +2.35 +I230
a C0.W *c 05 rO.05 m +1.2 +2.35 11 +iZJ0
a t0.m
4 t0.W) I 17 JAN 95 vrc 1B:U:J~
P f t s wc. m 1 1 0 1 M O T NODE A C T I V I T Y : \ I
NORMAL DISEHGAGED OVERSPEED M O T ACT
/
. 1
orrt
FLARE C C W
BANK ANGLE P R O 1
1 7 JAN 95 w< l8:44:3& DATE AND T I N E
1
/
I J
AUTO EVENT
HESSAGE F I E L D
The belt worn PC is a recent innovation with the computer strapped to the belt
and a one inch liquid crystal display strapped to the head. The computer is
voice commanded which leaves both hands free to 'get on with the work'.
'On-boqd' manuals will afford u s the opportunity to look at the FIM and the
AMM without actually leaving the aircraft. Caution needs to be taken when
using this style of information that it is in fact current a n d t h a t any temporary
revisions are also incorporated. That may well mean a trip to the technical
I
library in any case.
H E A D STRAP
EAR PHONE
COMPUTER UNIT
We need to be careful, with all this technology, that we don't become blinkered
during fault diagnosis. In a way it is like using a calculator, we must have
some idea of what the expected result should be. If the calculator gives u s a
result that is wildly different from what we expected then we should consider
the possibility if mis-use of the calculator - incorrect keying etc. The same with
electronic fault diagnosis, we should think what the computer is telling us
what to do and it should make sense with our own logical reasoning.
Don't forget that ultimately you will still have to leave the flight deck and go to
the actual system to carry out what-ever rectification is called for.
That concludes this section on the additional functions of the CMC and indeed
our study about on-board maintenance and ATA 45, a new chapter and
concept to some of us. Try the following exercises. The answers are found in
the text.
7,?7),,>)''7,,),
rnoodull l A-1523
1. What is BITE?
2. What is a central maintenance LED panel a n d how does it operate?
3. How, basically, does t h e CMC work?
4. Explain where and how the CMC displays its failure codes.
5. How do you fault find using the CMC and FIM?
6. What is a flight leg?
7. Explain the reportable region and the logic?
8. Why and what do we 'correlate'?
9. Explain the route through the CMC that a fault code takes.
10. Briefly state what faults you would expect to see in present leg
faults (inbound faults) and existing faults?
11. Describe what you would expect to see in the fault history.
12. What is a ground test?
13. Name some of the functions of the data loading capability.
14. What type of printers are normally used?
15. How do we change a QAR disc and what sort of disc is it?
16.- What is a snapshot-and when,might we expecpto u s e one?
17. As with all cornpufer systems the only way to get farnili& with
' them is to use the system. If hossible, and with supervision -
unless you are alreAdy cleared to work on your pikcraft - have a
I look a t the CMC pages - if you have access. Get1 to grips with the
basic layout and how to navigate your way arounq. If y,ou do not
have access then re-read-any parts of this book on-areas/you are
18.
I
unsure.
Look' in ATA45 for
1 \ \ I I - -
SAQ 4. The process for replacing a battery is given in the electrical section of
the LBP study boolts. On modern digital aircraft we must consider the fault
history. To remove the power and the battery, will erase any history that is
stored. We must now change the battery with power applied.
- 32 -
rnoodull l A-1525
APPENDIX
GLOSSARY OF TERMS
AGS Air Ground Sensing. Many systems on the aircraft must not work in the
air or must not work on the ground. Switches on the aircraft landing
gear allow the systems to know when the aircraft is airborne or on the
ground.
1 I - - /
/
1
ATA ~ : Transport
r ~ s s o c i a t i o hATA
. 100'~rovidesall aircreft T r i i u a l s with a
standard format recogniieh worldwide.
l 1 1 -
1 I ' I I
CDU Control and Display Unit. A device in the flight deck that allows
personnel to communicate with the various computers on board. Some
information is also displayed on the screen and selections are made
using the line select keys.
DFDR Digital Flight Data Recorder. With the advent of CMC, it became
possible to supply the flight recorder by using information that h a s
already gone to the CMC. ARINC 427 communication is often used to
perform this function.
ETOPS Extended Twin range Operations. Specific conditions (which are more
strict that when operating a four engined aircraft over the same route)
apply to twin engined aircraft that fly for extended periods.
FRM Fault Reporting Manual. A reference guide that the aircrew might use
to hrovide ground engineering with a fault code. Not used much these
days as BITE usually provides that information.
IRS Inertial Reference System. A laser gyro system, that provides position
and attitude information.
LED Light Emitting Diode - see basic electronic notes for details.
LSK Line Select Key. Each CDU will have a series of these. On the display
a n arrow points to the LSK. To select that particular option press the
LSK.
PCU Powered Control Unit. A hydraulic actuator that converts the pilot's
inputs be they electrical or mechanical into hydraulic pressure to move
the flying control surfaces.
QAR Quick Access Recorder. An optical device that is used to remove the
specific data required by the regulatory authority for aircraft
monitoring.