à
!"!#$%!&"!$'(#$)
à*) à à
4. With the help of P-V diagram explain how the variation in specific heats and dissociation of?gases tend
to deviate the ideal processes?
[ How the variation of specific heats takes' with temperature? What' are the physical Explanations for
variation of specific heats?
. Explain the effect of fuel-air ratio on, i) Efficiency. ii) Maximum power. iii) Maximum temperature. iv)
Maximum pressure v) Exhaust temperature.
What are combustion charts? Where theses are used and why?
What is the effect of percentage change in the efficiency of Otto cycle having a compression ratio of
7, if the specific heat at constant volume increases by 1 %
In an oil engine, working h ?dual combustion cycle the temperature and pressure at the beginning of
compression, are 90°C and 1 bar. The compression ratio is 13:1. The heat supplied per kg of air is 1672
KJ, half h?which is supplied at constant volume and half at constant pressure. Calculate i) the maximum
pressure in the cycle, and ii) the percentage of stroke at which cut off occur. Take r for compression 1.4;
Cv for products of combustion, 0.71+18.81 *10-5 T and R = O.287kJ/kgK.
R The air fuel ratio of a Diesel engine is 29: 1. If the compression ratio is 16: 1 and the temperature at
the end of compression is 900 K, find at what cylinder volume the combustion is complete. Express this
volume as percentage of stroke. Assume that the combustion begins at the top dead center and takes
place at constant pressure. Take calorific value of the fuel as 42 mJ/kg, R= 0.287 ð ð?and Cv = 0.709
+O.000028T ð ð
o A petrol engine having a compression ratio of 6 uses a fuel with a calorific value of 42 MJ/kg. The air-
fuel ratio is 15:1 Pressure and temperature at the start of suction stroke are1 bar and å ?respectively.
Determine the maximum pressure in the cylinder if the index of compression is 1.3 and the specific heat
at constant volume is given by v 0.678+ 0.00013T, where T is in Kelvin. Compare this value with that
obtained when Cv =0.717 kJ/kgK.
à+)
à
à ,à à
à
1. With a neat pressure crank angle diagram, explain the stages of combustion in SI engine.
2. Explain the effect of following engine variables on ignition lag: .i) Mixture ratio ii) Initial temperature.
iii) Electrode gap.
5. Discuss'. The effect of the following parameters on the name propagation of SI engines: i) A:F ratio ii)
Compression ratio iii) RPM of the engine iv) Engine load v) Turbulence.
6. What are the factors that limit the compression ratio in Petrol engine?
7. Explain the difference between: i) Pre-ignition ii) Ant ignition iii) Detonation.
8, Describe the phenomenon, of knocking in SI engine. Explain four main factors which affect the
tendency to knock.
à)
à à à
à
4 What are two basic differences in the combustion process of SI and CI engines?
[ With the help of pressure-crank angle diagram, explain the stages of combustion in CI engines.
How does the detonation in SI engine differ from diesel knock? Explain.
Compare 'Knocking' in SI and CI engines with reference to following engine variables.
iii. Delay period for fuel. iv. Inlet temperature v. Inlet Pressure.
What is meant by delay period? Explain the effect of the following factors on delay period:
i) Fuel properties ii) Intake temperature iii) Compression ratio iv) Engine speed v) Type of
combustion chamber vi) Engine speed.
i) Compression ratio. ii) Quality of the fuel.iii) Injection pressure. iv) Engine speed.
v) Intake temperature.
o Discuss any three important variables that affect the delay period in combustion.
Explain how diesel engine knock differs from S.I engine knock.
à-)
à
With simple sketch explain air-cell chamber type divided combustion chamber.
[ How C.I. engine combustion chambers are classified? What type of swirl are used in these chambers
What are the advantages of overhead valve combustion chambers over side valve combustion-
chambers? Give neat sketches of both.
Give any two advantages of induction swirl. Sketch and explain Ricardo swirl chamber.
Draw neat layout of I and F head combustion chambers. Discuss their advantages and
disadvantages.
What are the requirements of CI combustion chamber for Diesel engines? Explain why weak
mixtures give less efficiency in CI Engines
What are F-head combustion chambers? Sketch any two F-head designs.
UNI.)UE
4 Write a brief note on the following:
. Write a short note on the air fuel ratio requirements of a petrol engine from no load to full load..
Explain the reasons for looking for alternate fuels for IC engines.
Explain alcohols as alternate fuels for IC engines bring out their merits and demerits.
What are the four main constituents of crude petroleum? Explain any three constituents giving
general formula, chemical structure. Also mention whether they are saturated or unsaturated
compounds.
Explain the SI-engine air fuel requirements under following conditions: i) Idling , ii) Cruising. iii) High
power range.
. Discuss the importance of: i) Gum content. ii) Heat of combustion iii) Sulphur content for a diesel
fuel
Write short note on mixture strength requirements of a petrol engine from no load to full load.
Briefly explain with a neat sketch the operation of a simple float type carburetor
4 What are the functional elements required for accomplishing the objectives of diesel engine fuel
injection system? Also mention the location of these elements with the help of symbolic
representation explain i) Individual pump and injector type. ii) Common rail type
Explain the following with simple sketches i) Thermostat ii) Radiator
[ Discuss five important requirements of an ideal diesel injection system.
Name different methods used for circulating the water around the cylinder and cylinder head.
How are injection systems Classified ? Describe them briefly. What are the limitations of air
injection system?
. With a neat sketch explain :i) Forced circulation-cooling system. ii) Evaporative cooling system.
. Describe with suitable sketches common rail system and distributor injection.
What is the function of a radiator? Explain the construction of a typical radiator system of fuel.
UNI)MODENDEVOO,MENS
What is meant by multi fuel engine? What arc the requirements of multi fuel engines?
Explain the effect of supercharging on the following parameter i) Power output. ii) Mechanical
efficiency.
What are the advantages and disadvantages of rotary combustion Engine compared to reciprocating
engine
UNI/)EMMISSIONEGUOSNDCONOSYSEMS
. Explain how NOx emissions are controlled by exhaust gas recirculation.
"A catalytic converter package is a total emission control package". Explain.
[ What are the main constituents of exhaust emission from Petrol-engine? Plot their nature and
variation with respect to air: fuel ratio.
Explain the mechanism of formation of N02 in petrol engine. With a suitable sketch explain the
control of N02 by Exhaust Gas Recirculation (EGR) method.
. With a suitable diagram explain the following emission control systems: i) Thermal reactor
package. ii) Catalytic converter package.
. Describe the exhaust gas recirculation method for the control of nitrogen oxides (NOx).
à