0 penilaian0% menganggap dokumen ini bermanfaat (0 suara)
63 tayangan3 halaman
ASMI - Advanced System Management Interface Every firmware service processor on a Power5 box has 2 Ethernet interfaces used for connection to the Hardware Management Console (HMC) if no DHCP adress is received it falls back to the default adress: 192.168.2.147 / 255.255.255. If you see HMC=1 or HMC=0 on the led screen you will not be able to get serial connection.
ASMI - Advanced System Management Interface Every firmware service processor on a Power5 box has 2 Ethernet interfaces used for connection to the Hardware Management Console (HMC) if no DHCP adress is received it falls back to the default adress: 192.168.2.147 / 255.255.255. If you see HMC=1 or HMC=0 on the led screen you will not be able to get serial connection.
Hak Cipta:
Attribution Non-Commercial (BY-NC)
Format Tersedia
Unduh sebagai RTF, PDF, TXT atau baca online dari Scribd
ASMI - Advanced System Management Interface Every firmware service processor on a Power5 box has 2 Ethernet interfaces used for connection to the Hardware Management Console (HMC) if no DHCP adress is received it falls back to the default adress: 192.168.2.147 / 255.255.255. If you see HMC=1 or HMC=0 on the led screen you will not be able to get serial connection.
Hak Cipta:
Attribution Non-Commercial (BY-NC)
Format Tersedia
Unduh sebagai RTF, PDF, TXT atau baca online dari Scribd
Interface Every firmware service processor on a Power5 box has 2 Ethernet interfaces used for connection to the Hardware Management Console (HMC). Immediately after the power cord is connected to the p5 system, service processor sends a DHCP request through both interfaces. If no DHCP adress is received it falls back to the default adress:
HMC1 Port: 192.168.2.147 / 255.255.255.0
HMC2 Port: 192.168.3.147 / 255.255.255.0 You
can connect to ASMI webinterface through the browser. See http://publib.boulder.ibm.com/infocenter/eserv er/v1r3s/index.jsp?topic=/iphbp/kickoff.htm for more information 2.
How do determine SFP IP adress
If the default IPs above are not accessible and you do not have access to any DHCPd logs which may have provided an adress you can use following procedure to determine the adress through 3 white buttons at the operation panel below the led: 1.
Select function 02 2.
Change "N" to "M" (for manual) 3.
Select function 30 4.
Change "**" to "00" and press Enter 5.
See the adress of HMC1 at "00" and HMC2 at
"01" 6.
Select function 02 7.
Change "M" back to "N"
3. Connection to ASMI through serial cable Service Processor FSP is also accessible through serial line connection. See ftp://www6.software.ibm.com/software/develop er/library/l-pow-opsetup.pdf for detailed settings. ASMI-access Page 2 of 2
This connection is only active if the box is not
currently connected to HMC or was connected to it in the last 14 days. If you see HMC=1 or HMC=0 on the LED screen you will not be able to get serial connection. You can reset the service processor and make it forget its HMC connection. See http://publib.boulder.ibm.com/infocenter/eserv er/v1r3s/index.jsp?topic=/iphby/ascii.htm for more information. 4. Disconnecting an HMC In order to get serial access to the operating system you may need to disconnect the system from HMC and make it forget the HMC connection. This happens by default after 14 days, but if you do not like to wait so long follow the procedure described at http://publib.boulder.ibm.com/infocenter/eserv er/v1r3s/index.jsp? topic=/iphbp/disconnecthmc.htm
Cybersecurity: A Simple Beginner’s Guide to Cybersecurity, Computer Networks and Protecting Oneself from Hacking in the Form of Phishing, Malware, Ransomware, and Social Engineering
Evaluation of Some Websites that Offer Virtual Phone Numbers for SMS Reception and Websites to Obtain Virtual Debit/Credit Cards for Online Accounts Verifications
Hacking: A Beginners Guide To Your First Computer Hack; Learn To Crack A Wireless Network, Basic Security Penetration Made Easy and Step By Step Kali Linux