(iii)
h.
Define the terms (i) Vestigial side band modulation (ii) High level slow level modulation. Explain the following terms (i) Pre-emphasis (ii) De-emphasis. Draw the block schematic of FM receiver. Compare AM and FM. Explain traffic load and grade of service in Telephone system. Write short notes on DTMF dialing. Define sensitivity and selectivity associated with communication receiver. PART B (4 x 15%0) Derive from fundamentals, the power derived in an amplitude modulated signals, Explain the SSB method of modulation. OR Explain Double-tuned super heterodyne receiver. Explain the principle of operation of envelope detector. Draw and explain the complete block diagram of Armstrong Frequency modulation system. Compare narrow Bend FM and wide band FM. OR Explain FM stereo receiver. Explain the working of balanced slope detectors. Discuss the types, causes and effects of various terms of noise in communication system. What is the importance of AGC circuit in receiver? OR Write short notes on Capture effect Image frequency and its rejection Carrier thresholding Double spotting What is none temperature? Explain different types of signaling. Briefly explain the operation of cross bar type telephone exchanges. OR Explain different types of tones used in automatic telephony. Write short note on Traffic variation In channel signalling. *** (10) (5) (12) (3) (10) (5) (10) (5) (12) (3)
II.
III. IV.
V.
VI.
VII.
a.
b. VIII.
IX.
(0
IV.
(a)
(8) (7) (10) (5) (15) (8) (7) (3) (6) (3) (3)
(d)
(15)
BTS(C) IV 10 016 A
PART- B (4 x 15 = 60) (a) (b) (a) (b) Draw and explain the V-I characteristics of an SCR. Explain construction and working of a TRIAC. OR Explain the problems associated with the series and parallel operation of SCRs. Draw and explain an RC trigger circuit for an SCR.
Derive an expressions for the average output voltage of a single phase full wave fully controlled bridge converter, supplying RL load. OR Draw the circuit of a 3d full wave rectifier with R load and explain its working with suitable wave forms.
Explain the various commutation schemes for SCR. OR Describe any one scheme for controlling the speed of a 3 phase induction motor.
With circuit diagram, explain the operation of a battery charging scheme. OR Explain the principle of induction heating. What are its applications? **
BTS(C) IV 10 012 L
(8 x 5 -= 40)
I.
a.
h.
Write a short note on usage of temporary registers in 8085. Write the usages of 8085 pins (i) READY (ii) ALE Differentiate between the op-codes LHLD and LDAX. Write a short note on various rotate instructions and their functionalities in 8085. Write a short note on (i) T State (ii) Machine cycle Draw an Instruction Fetch Timing Diagram of 8085. Write a short note on various ports available in 8255. Write a note on Transmitter section of 8251 peripheral device. PART B (4 x 15 = 60) (8) (7) (15) (8) (7)
II. III.
Differentiate between I/O Mapped I/O and Memory mapped I/O mapping techniques. Describe the Register organization of 8085 in detail. OR Write the functions of following group of pins in 8085. (iii) SID, SOD (ii) HOLD, HLDA (i) SO, SI Explain various addressing modes available in 8085 with the help of examples. Design and write a Delay routine for 1 second delay. Assume the clock speed of microprocessor is 3 MHz. OR Write an assembly Language program in 8085 to range a set of numbers stored from memory address 3001 onwards in ascending order and number of elements in the set is available in location address 3000. Write a short note on stack based op-codes and how will it modify the contents of register SP. Draw and explain the timing diagram for the instruction LDA 3000. OR Describe various types of interrupts and their organization in 8085. Write the concept of memory interfacing with the help of an example. Draw the architecture and register organization of peripheral chip 8251. OR Describe various operating modes and control words of peripheral chip 8255. Design an interface circuit to accept 8 bits of data from a ADC and produce various control signals according to the data read is less than 128 The data read is equal to 128 The data read is greater than 128
IV.
V.
VIII.
a. b.
IX.
(iii)
Also write the program for implementing the interfacing circuit. ***
PART B (4 x 15 = 60) II. Check whether the following systems are (a) causal or non-causal (b) static or dynamic (i)
y( t)cPy(t)1
n+1
Y( n) =
K=-0c,
x(k)
(3 x 5 = 15) (10)
(iii)
iii.
n (o)
List
(i)
h(t).:
4e-2111.
2 (a) (b) Determine the output response y (n) Find the inverse fourier transform of
(10)
X (eft' ). 1 ;
and
<= n/ 4
(5) (15)
VI.
VII.
(a) (b)
Write short notes on : Random process Stationary and non stationary random process Ergodic process. OR Explain the probability density function. A random variable has a probability distribution function given by
(3 x 5 = 15) (10)
0<x<co the probability that x > 0.6 the probability that x 5 0.25 the probability that 0.4 < x 5 0.8
(5)
VIII.
Explain (i)
Narrow band noise Effective noise temperature Pre-emphasis and De-emphasis filtering. OR Derive an expression for noise figure in a communication system. ***
(3 x 5 = 15) (15)