COOLING POWER
e .
d r
k c in
im l
.c a
m o
CE
Help
A conditioned enclosure absorb or dissipate heat through its walls according to its material, dimensions and the difference between internal enclosures and ambient temperature (t). This value is determinate by a simple calculation (m2 x t x5)W, (as assuming the enclosure made in steel, transfer coefficient = 5), see the selection chart below for a quick reference:
t C
30 25 20 15 10 5 0 0 125 250 375 500 625
10
11
12
13
14
15
750 875 1000 1125 1250 1375 1500 1625 1750 1875 2000 2125 2250
First question to ask in order to select the appropriate cooling equipment is: Can the internal enclosure temperature be higher than the external ambient temperature ? If the answer is NO, we will choose between an air conditioner and a water to air heat exchanger. In this case, the heat absorbed by the enclosure, at specified limit conditions, has to be added to the heat dissipated by the internal components. Using an air conditioner can be maintained constant the internal enclosure temperature, independently from the variation of outside ambient temperature. If an air conditioner is used, it is suggested to keep the internal temperature to a minimum of 30C to avoid condensate water production when an operator will open the enclosure door. Temperatures lower than 30C may cause the installed components to be covered of condensate water when warmer external air enter in the enclosure. If the answer is YES, we will choose an air to air heat exchanger or a forced ventilation system, that uses filtered primary air. In this case the heat absorbed by the enclosure, at specified limit conditions, has to be removed from the heat dissipated by the installed components. Air to air heat exchanger cooling capacity is measured in W/K, this value indicates how many Watt the heat exchanger can remove for every degree of temperature difference between internal enclosure temperature and external ambient temperature. For example, a 30 W/K cooling capacity heat exchanger can remove 450W of heat, if ambient temperature is 35C and internal enclosure temperature is 50C (i.e. 50-35 = 15 difference of temperature x 30 = 450W). Only as an indication, heat dissipation by components can be calculated using the below table: transformers drivers, PLC, numerical controls , inverters suppliers moving-coils relay, contactors incandescent lamps heaters
Above table only give approximate values for components. Particular attention should be given to high power components and it is suggested to consult the component's manufacturer in order to obtain an accurate value and to avoid wrong calculations of heat dissipation.
w
A B C D E L T P Q R V W
e .
d r
k c in
im l
.c a
W
m o
AVAILABLE POWER SUPPLIES 230 1 50 230 1 60 230 1 50 / 60 110 - 115 1 50 / 60 440 - 480 3 60 415 3 60 400 - 415 3 50 400 2 50 400 2 60 440 - 480 2 60 24 V DC 48 V DC
Index
Air
LOW MAINTENANCE Units marked with this symbol require only air filter cleaning and no other periodical maintenance.
conditioners
From pag. 10 to pag. 29
NO MAINTENANCE Units marked with this symbol do not require any periodical maintenance.
ENERGY SAVING This symbol indicates that the product has been designed to optimise its energy consumption according to the provided working conditions. (DIN3168L35L35).
Ventilation
ANTI-CONDENSATE DEVICE This device collects condensate and evaporates this off into the ambient atmosphere, thus ensuring that the air left inside the machine is dry and the surfaces are moisture-free.
OZON FRIEND Is the symbol that represents Kelvin's permanent commitment in preserving the environment around us. All refrigeration techniques take environmental protection into consideration by using cloro-fluorocarbon-free (CFC) refrigerants, which are not harmful to the ozone layer.
e .
d r
Anticondensation heaters
Pag. 41
k c in
im l
.c a
m o
pag. 40
Accessories
Pag. 42
Sales network
Pag. 43
KMV
he KMV is a very compact air conditioner for vertical installation on the outside face of the door or wall of an enclosure, especially designed for applications where space is limited, like small control panels. It is suitable for low cooling capacities. The condensate drain is positioned on the bottom of the air conditioner. Four M6 threaded inserts will enable easy screw-on installation.
Standard
Optionals
CE
w
10
e .
d r
k c in
MODEL:
im l
500
.c a
170
Free voltage contact for dirty filter and max temperature alarm
m o
280
KMV 03
Standard power supply (C) Running current Starting current Protection fuses Cooling capacity L35 L35 Cooling capacity L35 L50 Power absorbed L35 L35 Refrigerant Maximum pressure Temperature range Internal circuit protection degree External circuit protection degree Noise level Weight Available power supplies
V - Hz A A A W W W bar C IP IP dB (A) kg
230 - 50/60 1,2 / 1,4 6,2 / 6,2 2 330 / 347 248 / 257 216 / 247 R134a 27 20 - 55 54 34 62 17 C, D
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
KUR
he KUR05 and KUR09 are two compact air conditioners designed to be installed on the outside face of the door or wall of an enclosure. These can also be installed internally or semi-concealed using an optional mounting frame. They are made from galvanised steel with an easily removable cover with rounded edges. KUR05 and KUR09 are both designed to operate without an air filter, available as an option and recommended if the working environment is particularly dusty or oily. The condensate drain is positioned at the bottom of the air conditioners. Six M6 threaded inserts will enable easy screw-on installation. Standard Optionals
Aluminium or polyurethane air filter 3 meters power supply cable connected in therminal board
CE
e .
SEMI-CONCEALED ASSEMBLY
EXTERNAL ASSEMBLY
INTERNAL ASSEMBLY
d r
k c in
im l
.c a
215 605
Free voltage contact for dirty filter and max temperature alarm
m o
305
MODEL:
KUR 05
KUR 09
Standard power supply (C) Running current Starting current Protection fuses Cooling capacity L35 L35 Cooling capacity L35 L50 Power absorbed L35 L35 Refrigerant Maximum pressure Temperature range Internal circuit protection degree External circuit protection degree Noise level Weight Available power supplies
V - Hz A A A W W W bar C IP IP dB (A) kg
230 - 50/60 2,1 / 2,5 2,8 / 3,3 7,9 / 9,3 11,3 / 12,3 4 4 600 / 630 850 / 892 450 / 480 637 / 663 395 / 461 525 / 611 R134a 27 20 - 55 54 34 67 68 28 29 C, D
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
11
KUJ
he KUJ05 and 09 are two air conditioners designed to be installed on the outside face of the door or wall of an enclosure. These can also be installed semi-concealed using an optional frame. The large distance between the inlet and outlet of the internal circuit (enclosure side) helps to keep an even temperature in the cabinet. KUJ models are made from galvanised steel with an easily removable cover with rounded edges. On the front, an aluminium grid conceals the air filter and gives the air conditioner a pleasant look thanks to its design. The condensate drain is positioned at the bottom. Six M6 threaded inserts will enable easy screw-on installation. Standard Optionals
Aluminium air filter IP54 self adhesive gasket 3 meters power supply cable connected in therminal board Polyurethane air filter
w
12
e .
SEMI-CONCEALED ASSEMBLY
EXTERNAL ASSEMBLY
INTERNAL ASSEMBLY
MODEL:
KUJ 05
d r
k c in
CE
im l
.c a
190
Free voltage contact for dirty filter and max temperature alarm
m o
350
700
KUJ 09
Standard power supply (C) Running current Starting current Protection fuses Cooling capacity L35 L35 Cooling capacity L35 L50 Power absorbed L35 L35 Refrigerant Maximum pressure Temperature range Internal circuit protection degree External circuit protection degree Noise level Weight Available power supplies
V - Hz A A A W W W bar C IP IP dB (A) kg
230 - 50/60 2,2 / 2,7 2,9 / 3,5 8,2 / 9,7 11,6 / 12,7 4 6 600 / 630 850 / 892 450 / 480 637 / 663 445 / 516 570 / 666 R134a 27 20 - 55 54 34 67 68 25 29 C,D
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
KUN
he KUN series of air conditioners are designed to be installed on the outside face of the door or wall of an enclosure.These can be also installed internally or semi-concealed using an optional frame. They are made from galvanised steel with an easily removable cover with rounded edges. On the front, an aluminium grid conceals the air filter and gives the air conditioners a pleasant look thanks to its design.This product line is provided with a water condensate dissipater and emergency condensate drain at the bottom. Six M6 threaded inserts will enable easy screw-on installation. Standard Optionals
Aluminium air filter 3 meters power supply cable connected in therminal board Polyurethane air filter
Inlet 3 pole connector Electrical control board - keeps temperature at set point - visualises temperature inside the control board - provides voltage free contacts for dirty filter and high temperature alarms - protected programming access (within 1' from power-on)
Lifting eyebolts
OPTION: KUN10 and KUN20 230/1/50-60 without electronic diagnostic card are available on cCSAus comply version. User manual in five languages
e .
SEMI-CONCEALED ASSEMBLY
EXTERNAL ASSEMBLY
INTERNAL ASSEMBLY
d r
k c in
CE
im l
.c a
230 1000
Free voltage contact for dirty filter and max temperature alarm
m o
400
MODEL:
KUN 10
KUN 15
KUN 17
KUN 20
V - Hz Standard power supply (C) A Running current A Starting current A Protection fuses W Cooling capacity L35 L35 W Cooling capacity L35 L50 W Power absorbed L35 L35 Refrigerant bar Maximum pressure C Temperature range Internal circuit protection degree IP External circuit protection degree IP dB (A) Noise level kg Weight Available power supplies
2,9 / 3,5 11,6 / 12,7 4 1050 / 1102 778 / 819 570 / 666
45 C,D,P,Q,R
230 - 50/60 4,2 / 5,2 5,4 / 6,6 5 / 6,1 16,6 / 17,2 20,4 / 21,1 23,6 / 24,2 6 10 10 1360 / 1428 1720 / 1806 2000 / 2100 1020 / 1060 1290 / 1342 1500 / 1560 1050 / 1278 1045 / 1272 830 / 1014 R134a 27 20 - 55 54 34 70 49 52 48 C,D,P,Q,R C,D,P,Q,R C,D,E,P,Q,R,T
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
13
KUN
he KUN series of air conditioners are designed to be installed on the outside face of the door or wall of an enclosure.These can be also installed internally or semi-concealed using an optional frame. They are made from galvanised steel with an easily removable cover with rounded edges. On the front, an aluminium grid conceals the air filter and gives the air conditioners a pleasant look thanks to its design.This product line is provided with a water condensate dissipater and emergency condensate drain at the bottom. Six M6 threaded inserts will enable easy screw-on installation. Standard Standard Optionals
Aluminium air filter
Electrical control board - keeps temperature at set point - visualises temperature inside the control board - provides voltage free contacts for dirty filter and high temperature alarms - protected programming access (within 1' from power-on) Lifting eyebolts
OPTION: KUN40 400/3/50 and 440-460/3/60 without electronic diagnostic card are available on cCSAus comply version.
w
14
e .
SEMI-CONCEALED ASSEMBLY
EXTERNAL ASSEMBLY
d r
k c in
CE
im l
1205
.c a
305
Free voltage contact for dirty filter and max temperature alarm
m o
500
MODEL:
KUN 30
KUN 40
V - Hz Standard power supply (A) A Running current A Starting current A Protection fuses W Cooling capacity L35 L35 W Cooling capacity L35 L50 W Power absorbed L35 L35 Refrigerant bar Maximum pressure C Temperature range IP Internal circuit protection degree External circuit protection degree IP dB (A) Noise level kg Weight Available power supplies
230 - 50 6,7 / 8,3 6,8 / 8,3 37,2 / 44,6 33,2 / 42,6 10 2800 / 2940 3800 / 3990 2100 / 2184 2850 / 2964 1155 / 1444 1405 / 1744 R134a 27 20 - 55 54 34 72 83 87 A,B,E,T (60Hz)
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
KUS
he KUSs are designed for outdoor installations on walls or control board doors. With a depth of only 115mm, a painted cowling with rounded edges and the particular design of the aluminium front grill supporting the air filter, the KUS has all the features that offer an elegant cooling solution. The compressor is positioned in the lower part of the air conditioner and provision must be made behind the door for the extra intrusion of the compressor body beyond the depth of the KUS. Four M6 threaded inserts are provided for installation. The condensate outlet is positioned on the lower part of the air-conditioner. Standard
Gasket roll
Optionals
3 meters power supply cable connected in therminal board
Free voltage contact for dirty filter and max temperature alarm Internal control thermostat set at 35 C.
CE
User manual in five languages
e .
EXTERNAL ASSEMBLY
d r
MODEL:
KUS 10
1510
k c in
im l
.c a
m o
400
115+60
KUS 15
KUS 17
KUS 20
V - Hz Standard power supply (C) A Running current A Starting current A Protection fuses W Cooling capacity L35 L35 W Cooling capacity L35 L50 W Power absorbed L35 L35 Refrigerant bar Maximum pressure C Temperature range Internal circuit protection degree IP External circuit protection degree IP dB (A) Noise level kg Weight Available power supplies
43
230 - 50/60 4,3 / 5,2 5,5 / 6,7 16,9 / 17,4 20,7 / 21,2 6 8 1450 / 1522 1700 / 1785 1088 / 1131 1275 / 1326 1080 / 1278 860 / 1014 R134a 27 20 - 55 54 34 70 49 48 C,D
5,1 / 6,2 23,9 / 24,4 8 2000 / 2100 1500 / 1560 1075 / 1272
46
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
15
Slim line
KSL
Optionals
Aluminium air filter
he KSL slim line air-conditioners are designed to be installed vertically inside and outside the control board. This new product line represents the latest technical innovation from Kelvin's research and development department. All parts are accessible by simply removing the front panel, so eliminating the need to remove the unit from the control board. This model can be used with or without an air filter. The condensate is collected and then dissipated into the external ambient. This unit can be installed outdoors without worrying about associated air pollutants. Standard
IP54 self adhesive gasket
NEW
Internal terminal board for wiring
w
16
e .
EXTERNAL ASSEMBLY
INTERNAL ASSEMBLY
d r
1500
k c in
CE
im l
.c a
190
Free voltage contact for dirty filter and max temperature alarm
m o
400
MODEL:
KSL 10
KSL 15
V - Hz Standard power supply (C) A Running current A Starting current A Protection fuses W Cooling capacity L35 L35 W Cooling capacity L35 L50 W Power absorbed L35 L35 Refrigerant bar Maximum pressure C Temperature range Internal circuit protection degree IP External circuit protection degree IP dB (A) Noise level kg Weight Available power supplies
230 - 50/60 2,4 / 2,8 3,6 / 4,2 12 / 13 15 / 18 4 6 1050 / 1102 1490 / 1545 778 / 819 1150 / 1200 425 / 465 650 / 715 R134a 27 20 - 55 54 34 69 50 C,D,P,Q,R
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
KSL
Slim line
Optionals
Aluminium air filter
he KSLs are designed for simple installation. The drilling template is common to all models, thus allowing interchangeability of unit sizes if the need to increase cooling power became necessary. In the internal mounted version the air-conditioner's front side, 20 mm thick, is leaned on the control board's panel covering so possible aesthetic defects.
Standard
IP54 self adhesive gasket
NEW
Internal terminal board for wiring
e .
MODEL:
KSL 20
EXTERNAL ASSEMBLY
INTERNAL ASSEMBLY
d r
1500
k c in
CE
im l
.c a
220
Free voltage contact for dirty filter and max temperature alarm
m o
400
KSL 30
KSL 40
V - Hz Standard power supply A Running current A Starting current A Protection fuses W Cooling capacity L35 L35 W Cooling capacity L35 L50 W Power absorbed L35 L35 Refrigerant bar Maximum pressure C Temperature range Internal circuit protection degree IP External circuit protection degree IP dB (A) Noise level kg Weight Available power supplies
230 - 50/60 (C) 4,7 / 5,6 22 / 24,2 8 2100 / 2200 1500 / 1560 870 / 1050 20 -55
56 C,D,E,P,Q,R,T
230 - 50 (A) 5,6 / 6,2 26 / 31 10 2900 / 3020 2190 / 2265 1055 / 1344 R134a 27 20 - 55 54 34 70 65 A,B,E,T (60Hz)
230 - 50 (A) 8,5 / 9,3 29 / 34,8 10 3300 / 3490 2450 / 2520 1220 / 1464 20 - 50
65 A,B,E,T (60Hz)
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
17
KZM
he KZM60 and 80 air conditioners are designed for side panel mounting. They are made from steel and painted and measure 2000mm high by either 600mm or 800mm wide respectively. These units are designed so that one unit can provide conditioned air to up to 6 cabinet modules in a row, supplying the air via a channel in the floor. Particular care has been taken when designing the KZM range of products to give the optimum performance/consumption ratio. The water condensate drain is positioned at the bottom. Eight M6 threaded inserts will enable easy screw-on installation. Standard
Gasket roll
Optionals
Aluminium air filter
Free voltage contact for dirty filter and max temperature alarm Internal control thermostat set at 35 C. Lifting eyebolts
3 meters power supply cable connected in therminal board Compressor start delay timer User manual in five languages
EXTERNAL ASSEMBLY
w
18
EXTERNAL ASSEMBLY
2000
KZM60
e .
KZM80
d r
MODEL:
k c in
CE
im l
.c a
m o
600 800
KZM60 KZM80
380
KZM 60
KZM 80
Standard power supply (T) Running current Starting current Protection fuses Cooling capacity L35 L35 Cooling capacity L35 L50 Power absorbed L35 L35 Refrigerant Maximum pressure Temperature range Internal circuit protection degree External circuit protection degree Noise level Weight Available power supplies
V - Hz A A A W W W bar C IP IP dB (A) kg
400 - 3 - 50 6 / 6,9 7,6 / 8,5 21,4 / 23,2 30,4 / 32,2 8 10 5700 / 5985 7500 / 7875 4275 / 4446 5625 / 5850 2340 / 2928 3140 / 3828 R407C 27 20 - 55 54 34 72 150 160 E,L,T (60Hz)
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
KB
he KB 04 is a very compact air-conditioner and is particularly suitable for fitting on the top of small control boards which require minimal cooling within limited room conditions. The internal recycled cooled air is parallel to KB04s longitudinal axis. Four M6 threaded inserts are provided for installation. The condensate outlet is positioned on the unit's rear side.
Standard
Optionals
Aluminium air filter
IP54 self adhesive gasket 3 meters power supply cable connected in therminal board
CE
Internal control thermostat set at 35 C.
e .
250
d r
k c in
MODEL:
im l
350
.c a
Free voltage contact for dirty filter and max temperature alarm
m o
500
KB 04
Standard power supply (C) Running current Starting current Protection fuses Cooling capacity L35 L35 Cooling capacity L35 L50 Power absorbed L35 L35 Refrigerant Maximum pressure Temperature range Internal circuit protection degree External circuit protection degree Noise level Weight Available power supplies
V - Hz A A A W W W bar C IP IP dB (A) kg
230 - 50/60 1,9 / 2,2 6,8 / 6,9 4 490 / 515 368 / 382 360 / 419 R134a 27 20 - 55 54 34 67 22 C,D
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
19
KB
he KBs are air-conditioners designed to be fitted on the roof of control boards requiring a transverse cooled air path when compared to the KBs longitudinal axis. The supporting structure is made from galvanised steel sheet and an elegant aluminium grid supports the standard polyurethane air filter. Four M6 threaded inserts are provided for installation. The condensate outlet is positioned laterally on its right side.
Standard
IP54 self adhesive gasket
Optionals
Aluminium air filter 3 meters power supply cable connected in therminal board
Lifting eyebolts
CE
Antifreeze thermostat
w
20
e .
300
d r
k c in
im l
400
.c a
Free voltage contact for dirty filter and max temperature alarm
m o
600
MODEL:
KB 10
KB 15
KB 17
Standard power supply (C) Running current Starting current Protection fuses Cooling capacity L35 L35 Cooling capacity L35 L50 Power absorbed L35 L35 Refrigerant Maximum pressure Temperature range Internal circuit protection degree External circuit protection degree Noise level Weight Available power supplies
V - Hz A A A W W W bar C IP IP dB (A) kg
2,9 / 3,5 11,6 / 12,7 6 1000 / 1050 750 / 780 570 / 666
37
230 - 50/60 4 / 4,8 16,2 / 16,4 6 1450 / 1522 1087 / 1131 785 / 924 R134a 27 20 - 55 54 34 70 41 C,D,P,Q,R
41
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
KB
Standard Optionals
Aluminium air filter IP54 self adhesive gasket 3 meters power supply cable connected in therminal board Polyurethane air filter
Lifting eyebolts
CE
Antifreeze thermostat
e .
400
d r
k c in
im l
400
.c a
Free voltage contact for dirty filter and max temperature alarm
m o
800
MODEL:
KB 20
KB 30
KB 40
V - Hz Standard power supply A Running current A Starting current A Protection fuses W Cooling capacity L35 L35 W Cooling capacity L35 L50 W Power absorbed L35 L35 Refrigerant bar Maximum pressure C Temperature range Internal circuit protection degree IP External circuit protection degree IP dB (A) Noise level kg Weight Available power supplies
230 - 50/60 (C) 5 / 6,1 23,7 / 24,2 8 2000 / 2100 1500 / 1560 1050 / 1272
54 C,D,E,P,Q,R,T
230 - 50 (A) 6,9 / 8,9 37,6 / 45,8 10 2800 / 2940 2100 / 2184 1115 / 1370 R134a 27 20 - 55 54 34 65 60 A,B,T,E (60Hz)
230 - 50 (A) 6,8 / 8,3 33,2 / 42,6 10 3800 / 3990 2850 / 2964 1405 / 1744
63 A,B,T,E (60Hz)
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
21
KT
he KTs are a range of air-conditioners designed to be fitted on the roof of a cabinet with a cold air recycle path parallel to its longitudinal axis. Its supporting structure is made from galvanised steel sheet and an elegant aluminium grid supports the standard polyurethane air filter. Four M6 threaded inserts are provided for installation. The condensate outlet is positioned on the unit's rear side.
Standard
Optionals
Aluminium air filter
IP54 self adhesive gasket 3 meters power supply cable connected in therminal board
Lifting eyebolts
CE
Antifreeze thermostat
w
22
e .
350
d r
k c in
im l
400
.c a
Free voltage contact for dirty filter and max temperature alarm
m o
600
MODEL:
KT 10
KT 17
V - Hz Standard power supply (C) A Running current A Starting current A Protection fuses W Cooling capacity L35 L35 W Cooling capacity L35 L50 W Power absorbed L35 L35 Refrigerant bar Maximum pressure C Temperature range IP Internal circuit protection degree IP External circuit protection degree dB (A) Noise level kg Weight Available power supplies
230 - 50/60 5,2 / 6,2 2,9 / 3,5 20 / 20,2 11,6 / 12,7 8 6 1700 / 1785 1000 / 1050 1275 / 1326 750 / 780 1005 / 1188 570 / 666 R134a 27 20 - 55 54 34 67 41 37 C,D,E,P,Q,R,T C,D,P,Q,R
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
KT
Standard Optionals
Aluminium air filter IP54 self adhesive gasket 3 meters power supply cable connected in therminal board Polyurethane air filter
CE
Lifting eyebolds
Antifreeze thermostat
e .
450
d r
MODEL:
k c in
im l
460
.c a
Free voltage contact for dirty filter and max temperature alarm
m o
800
KT 35
Standard power supply (A) Running current Starting current Protection fuses Cooling capacity L35 L35 Cooling capacity L35 L50 Power absorbed L35 L35 Refrigerant Maximum pressure Temperature range Internal circuit protection degree External circuit protection degree Noise level Weight Available power supplies
V - Hz A A A W W W bar C IP IP dB (A) kg
230 - 50 6,8 / 8,3 33,2 / 42,6 10 3500 / 3650 2625 / 2730 1350 / 1700 R134a 27 20 - 55 54 34 72 64 A,B,E,T (60Hz)
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
23
KCN
he KCN is an air conditioner for 19 rack cabinets. It has an aluminium front panel 6U high. Two handles on the front provide easy installation into an enclosure. Both the air intake and outlet of the external circuit are located on the front of the unit and so there is no need for cutouts through the enclosure side panels. The condensate drain is positioned on the front side of the unit.
Standard
Optionals
3 meters power supply cable connected in therminal board
Free voltage contact for dirty filter and max temperature alarm
CE
Antifreeze thermostat
w
24
e .
MODEL:
d r
483
k c in
266
im l
545
.c a
m o
445
KCN 05
KCN 10
KCN 15
Standard power supply (C) Running current Starting current Protection fuses Cooling capacity L35 L35 Cooling capacity L35 L50 Power absorbed L35 L35 Refrigerant Maximum pressure Temperature range Internal circuit protection degree External circuit protection degree Noise level Weight Available power supplies
V - Hz A A A W W W bar C IP IP dB (A) kg
2,2 / 2,7 8,2 / 9,7 4 600 / 630 450 / 480 445 / 516
25
230 - 50/60 2,9 / 3,5 11,6 / 12,7 6 850 / 892 637 / 663 570 / 666 R134a 27 20 - 55 54 34 67 37 C,D
41
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
KWS
he air-water heat exchanger KWS20 KELVIN is unique in representing the best in compactness and design. It is silent, long lasting and totally free of ordinary maintenance. It represents an optimised product designed to reach elevated performances. This offers the best choice when it comes to prohibitive working temperatures. Four M6 threaded inserts are provided for fixing onto the cabinet.
Standard
Optionals
IP54 self adhesive gasket 3 meters power supply cable connected in therminal board
NEW
CE
w
30
e .
d r
MODEL:
k c in
im l
.c a
600
Free voltage contact for dirty filter and max temperature alarm
m o
110
250
KWS 20
Power supply (C) Power absorption Cooling capacity L35/W10C Nominal current Protection fuses Air flow range Maximum pressure Temperature range (ambient) Internal circuit protection degree Connections Noise level Weight Available power supplies
230 - 50/60 29 / 28 635 - 250 lit/h 0,2 / 0,4 1 330 5 -5 +70 IP55 1/2 50 12 C,D,V,W
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
KWS
he KWS air to water heat exchangers can reach high cooling capacities with small dimensions. They represent the best choice if the working environment is particularly dusty, oily or hot. KWS offer IP55 protection rating and are very silent and reliable, with almost no maintenance required. Six M6 threaded inserts will enable easy screw-on installation.
Standard
Optionals
IP54 self adhesive gasket 3 meters power supply cable connected in therminal board
CE
User manual in five languages
e .
d r
MODEL:
k c in
im l
.c a
300 600
Free voltage contact for dirty filter and max temperature alarm
m o
160
KWS 30
Power supply (C) Power absorption Cooling capacity L35/W10C Nominal current Protection fuses Air flow range Maximum pressure Temperature range (ambient) Internal circuit protection degree Connections Noise level Weight Available power supplies
230 - 50/60 80 / 98 1600 - 200 lit/h 0,36 / 0,44 2 550 5 -5 +70 IP55 1/2 60 15 C,D,W
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
31
KWS
he KWS air to water heat exchangers can reach high cooling capacities with small dimensions. They represent the best choice if the working environment is particularly dusty, oily or hot. KWS offer IP55 protection rating and are very silent and reliable, with almost no maintenance required. Six M6 threaded inserts will enable easy screw-on installation.
Standard
Optionals
IP54 self adhesive gasket 3 meters power supply cable connected in therminal board
CE
User manual in five languages
w
32
e .
d r
MODEL:
1000
k c in
im l
.c a
400
Free voltage contact for dirty filter and max temperature alarm
m o
200
KWS 70
Power supply (C) Power absorption Cooling capacity L35/W10C Nominal current Protection fuses Air flow range Maximum pressure Temperature range (ambient) Internal circuit protection degree Connections Noise level Weight Available power supplies
230 - 50/60 85 / 90 3400 - 400 lit/h 0,38 / 0,4 2 850 5 -5 +70 IP55 1/2 65 29 C,D,W
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
KWS
Standard Optionals
IP54 self adhesive gasket 3 meters power supply cable connected in therminal board
CE
User manual in five languages
e .
d r
MODEL:
1200
k c in
im l
.c a
450
Free voltage contact for dirty filter and max temperature alarm
m o
250
KWS 90
Power supply (C) Power absorption Cooling capacity L35/W10C Nominal current Protection fuses Air flow range Maximum pressure Temperature range (ambient) Internal circuit protection degree Connections Noise level Weight Available power supplies
230 - 50/60 130 / 180 5400 - 600 lit/h 0,57 / 0,80 2 1230 5 -5 +70 IP55 1/2 68 34 C,D,W
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
33
KWS
he air-water heat exchangers KWS 100 and 120 are designed to reach elevated cooling performances. They are realized inside carpentry modules planned on purpose to be placed side by side to the cabinets, obtaining so an optimal aesthetic integration. Due to their functional characteristics these products are very simple, silent, long lasting and completely free of ordinary maintenance and represent the best choice in cases of prohibitive working temperatures. Eight M6 threaded inserts are provided for fixing on the control board. Standard Optionals
NEW
KWS100
w
34
e .
KWS120
d r
MODEL:
2000
k c in
CE
im l
.c a
Free voltage contact for dirty filter and max temperature alarm
m o
600 800
KWS100 KWS120
380
KWS 100
KWS 120
V - Hz Power supply (C) W Power absorption W Cooling capacity L35/W10C A Nominal current A Protection fuses m/h Air flow range bar Maximum pressure C Temperature range (ambient) Internal circuit protection degree IP Connections dB (A) Noise level kg Weight Available power supplies
230 - 50/60 150 300 12500 - 2000 lit/h 14000 - 2000 lit/h 0,66 1,3 4 2340 5 -5 +70 IP55 1 69 125 135 C,P,T
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
KSA
he KSAs 18-19 are air-air heat exchangers, which are particularly suitable for side or door installations on small control boards and other small enclosures which require minimal cooling within limited room conditions. These two models use four axial fans, which provide improved air circulation and temperature distribution. The external circuit fans can be controlled by a DIN bar thermostat, saving energy and reducing noise. The control board circuit fans have to run permanently to avoid heat-pockets from forming. Four M6 threaded inserts are provided for fixing onto the cabinet. Standard
IP54 self adhesive gasket Internal air path deflector
Optionals
CE
w
36
e .
EXTERNAL ASSEMBLY
INTERNAL ASSEMBLY
d r
k c in
im l
.c a
134
m o
316
380
MODEL:
KSA 18
KSA 19
Power supply (C) Cooling capacity Absorption Running current 50/60 Hz Protection fuses Internal circuit flow rate External circuit flow rate Noise level Temperature range (ambient) Internal circuit protection degree Weight Available power supplies
230 - 50/60 12 36 0,2 1 240 240 36 -10 +55 IP54 8 C,D,V,W 23 57 0,3 1 380 380 48 -10 +55 IP54 8
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
KSA
he KSAs 20-23 are air air heat exchangers designed to be fitted on the side, the door or the roof of control boards. The reduced depth to high performance ratio makes this one of the best product lines that the market can offer. Thanks to their high flow rate and head pressure , the radial fans ensure a correct air circulation and an unvarying temperature distribution. The external circuit fan can be controlled by a DIN bar thermostat, saving energy and reducing noise. The inside circuit fan runs permanently to avoid heat-pockets from forming. Four M6 threaded inserts are provided for fixing onto the cabinet. Standard Optionals
IP55
IP54 self adhesive gasket
CE
User manual in five languages
e .
EXTERNAL ASSEMBLY
INTERNAL ASSEMBLY
d r
782
k c in
im l
.c a
86
m o
318
MODEL:
KSA 20
KSA 23
Power supply (C) Cooling capacity Absorption Running current 50/60 Hz Protection fuses Internal circuit flow rate External circuit flow rate Noise level Temperature range (ambient) Internal circuit protection degree Weight Available power supplies
230 - 50/60 37 47 160 160 0,7 0,7 1 1 550 550 550 550 65 65 -5 +55 -5 +55 IP54 IP54 10 11 C,D,V,W
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
37
KSA
he KSAs 42-43 and 21 are air air heat exchangers designed to be fitted on the side, the door or the roof of control boards. The reduced depth to high performance ratio makes this one of the best product lines that the market can offer. Thanks to their high flow rate and head pressure , the radial fans ensure a correct air circulation and an unvarying temperature distribution. The external circuit fan can be controlled by a DIN bar thermostat, saving energy and reducing noise. The inside circuit fan runs permanently to avoid heat-pockets from forming. Four M6 threaded inserts are provided for fixing onto the cabinet. Standard Optionals
IP55
IP54 self adhesive gasket
CE
User manual in five languages
w
38
e .
d r
782
k c in
im l
.c a
86
m o
318
MODEL:
KSA 42
KSA 43
Power supply (C) Cooling capacity Absorption Running current 50/60 Hz Protection fuses Internal circuit flow rate External circuit flow rate Noise level Temperature range (ambient) Internal circuit protection degree Weight Available power supplies
230 - 50/60 37 47 160 160 0,7 0,7 1 1 550 550 550 550 65 65 -5 +55 -5 +55 IP54 IP54 10 11 C,D,V,W
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
KSA
Standard Optionals
IP55
IP54 self adhesive gasket
CE
User manual in five languages
e .
EXTERNAL ASSEMBLY
INTERNAL ASSEMBLY
d r
k c in
MODEL:
im l
1250
.c a
m o
318
107
KSA 21
Power supply (C) Cooling capacity Absorption Running current 50/60 Hz Protection fuses Internal circuit flow rate External circuit flow rate Noise level Temperature range (ambient) Internal circuit protection degree Weight Available power supplies
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
39
VENTILATORS
he KEA ventilation systems offer a wide range of functional solutions to cool control boards with primary air. There are two types available: the wall mounted version and the mini-tower for roof mount installations on control boards. They have a particularly high air flow rate. Ventilation with filtration represents an efficient solution in those cases in which the working ambient air is clean and the temperature inside the cabinet can be higher than the external one. KELVIN offers with the KEA product line a solution panoramic suitable to satisfy any applicative, aesthetic and technical need. The new and exclusive KEA200 has a wide filtering area. This highly efficient design practically eliminates the need to clean the filters and represents a perfect example of KELVIN's continual commitment to developing new and innovative designs for the future.
KEA 200
KEA 60 / 100
MODELLO:
Power supply (C) Air flow rate Dissipation power Frontal air speed Absorption Current absorption Protection degree Noise level Colors Power supply cable Dimension
w
W D H
e .
d r
V - Hz m/h W/K Ms W A IP dB (A) m mm mm mm Kg
k c in
KEA 60
im l
.c a
CE
m o
KEA 100
KEA 200
230 - 50/60 450 135 80 / 98 0,36 / 0,44 IP33 60 RAL7032 3 375 295 91 5,6 C,D,V,W
230 - 50/60 700 210 85 / 90 0,38 / 0,4 IP33 68 RAL 7032 3 375 295 91 5,9 C,D,V,W
230 - 50/60 700 210 1 85 / 90 0,38 / 0,4 IP33 68 RAL7032 3 300 90 1500 14 C,D,V,W
40
All drilling templates on outside view Noise level measured at 1 meter from the unit, 1,6 meter from the ground level, in free space
ANTICONDENSATION
HEATINGS
nti-condensate heaters are indispensable to avoid condensate from forming inside the cabinet during a unit's standstill and in instances of very low ambient temperatures or very high humidity. Since hot air tends to rise they have to be positioned in the lower part and possibly beneath those components that require protection. Maximum efficiency is reached installing the heater in a vertical position and orientating the supply cable downwards. In case of large cabinets it is advisable to use multiple low rate heaters to obtain an unvarying temperature distribution. All KELVIN heaters are provided with a snapping fitment for the DIN EN 5002 conform 35 mm bar.
CR TERM. + VENTIL. Power supply Air flow rate (m/h) Heating capacity (W) Maximum amperage (A) Protection class Protection degree Approvals Mounting Range of regulation (C) Dimensions (mm) MAXI VENTILATED Power supply Heating capacity (W) Maximum amperage (A) Superficial temperature (C) Protection class Protection degree Approvals Mounting Dimensions (mm) MINI Power supply Heating capacity(W) Maximum amperage (A)
K5R040
K5R042
K5R041
K5R043
II ( double isolation) 20 UL 20 UL 20 UL 20 UL
VDE, UL
K5R037
Approvals MIDI
Power supply
Heating capacity (W) Maximum amperage (A) Superficial temperature (C) Protection class Protection degree Approvals Mounting
10
0,8 70 II
e .
-
80 x 80 x178
AC/DC 110 - 250 max. 265V 20 1 110 II 54 Bar 35mm. DIN EN 50022 VDE, UL K5R029 VDE, UL K5R030 K5R031 K5R032 K5R033 K5R034 30 1,5 120 II 54
d r
K5R038 30 1 190
80 x 80 x252
k c in
400 2,2 75 I 20 VDE, UL K5R039
im l
.c a
m o
54
VDE, UL K5R028
AC/DC 110-250V max. 265V 15 0,5 165 I test 1600V 20 45 1 105 I test 1600V 20
-
I test 1600V 20
-
41
ACCESSORIES
7H.020 and K7H.021 are two electro-mechanical bimetal thermostats with contactors, which are normally open (with a blue regulation screw) and normally closed (with a red regulation screw) respectively. The former is suitable in controlling cooling devices (air-conditioners, air-water heat exchangers, air-air heat exchangers, and fans) or to provide high temperature alarms. The latter is suitable in controlling heating or anticondensate devices (anticondensate heaters) K9S.022 is a humidistat with a 35 mm DIN bar (EN 5002) mount and generally used to control the anticondensate heaters.
K7H.020
K7H.021
K9S.022
MODEL:
e .
d r
k c in
im l
.c a
m o
K7H.020 - K7H.021
MODEL:
K9S.022
Range of regulation Contact capacity Assembly Differential commutation Protection degree Approvation Box Dimensions (HxWxD)
from 0 to +60C 6A (1) 250 V AC DIN bar 35 mm 7K IP30 VDE, UL Plastic (UL94V0) 60x33x35 mm
Range of regulation Contact capacity Precision Protection degree Ambient temperature Dimensions (HxWxD)
42