92%(12)92% menganggap dokumen ini bermanfaat (12 suara)
11K tayangan80 halaman
Design size of the hole is taken as the basic size fur both, i.e, hole and shaft. Position of tolerance zone of the shaft may be above or below the zero line. Shaft may give a certain type of fit with a hole in the basic shaft system. Actual values of deviations corresponding to the so mentioned can be read from tables (see pages 80-83)
Design size of the hole is taken as the basic size fur both, i.e, hole and shaft. Position of tolerance zone of the shaft may be above or below the zero line. Shaft may give a certain type of fit with a hole in the basic shaft system. Actual values of deviations corresponding to the so mentioned can be read from tables (see pages 80-83)
Hak Cipta:
Attribution Non-Commercial (BY-NC)
Format Tersedia
Unduh sebagai PDF, TXT atau baca online dari Scribd
Design size of the hole is taken as the basic size fur both, i.e, hole and shaft. Position of tolerance zone of the shaft may be above or below the zero line. Shaft may give a certain type of fit with a hole in the basic shaft system. Actual values of deviations corresponding to the so mentioned can be read from tables (see pages 80-83)
Hak Cipta:
Attribution Non-Commercial (BY-NC)
Format Tersedia
Unduh sebagai PDF, TXT atau baca online dari Scribd
78 Westermann Tables
nits and Fits
Base hale stern
‘Basie dat se
“Taking the base size of a common reference for bat the systems, the lowing o-eaton exis
Design sae of the hol is akon athe busi ize for both,
le ole und shal. The position of tolerance zone ofthe
‘aft may be ahove or belo the er ine or in some cases
{eg jp the ze line may le within the tolerance zone of
tho shaft Depending upon the poston of oleae zone
ofthe shat the shaft may give a cera typeof ft with
toe inthe si ole sstem,
Desig sizeof the sf is taken a the bani ze fr bth,
ie Role and shaft ‘The postion of toerace zone of he
hole may he shove or below thee in in sme cases
e438) the zero line may li within he tolerance zone of
the hole, Depending upon the potion of tolrance zone
ofthe hol, the ole may give a certain type offic with
‘hal inthe basic shat system
zer0 19,
yen GY
Clearercest —Ineeranco st
1S-Eanyrumina 18: Foc
ar hole lower deviation is ero
Min mic = Basi size
Application: Machine and engine bulla, locomeaive
(2
Closranee ft ierorenco tt
For shalt upp deviation 280
‘Maxima imi = Base sie
Application: Electric motrs, bl bearings, power ens
mission, produts made fom bight draw has.
15 Symbol
While giving dimensions on drawings, the deviadons are not shown directly add to the basic size, hu the tlarnced sie ie
ince by is basi size followed by a synbo consisting af «eer (sometimes oles, gS) and a mamber,
For example instead of wing 2092, its menione a 209!" The atu vlues of deviations comesponding tthe sie
‘mentioned can be read rom table (ae pages 80-83),
ae
oes: opitl eters (3-H, G,M) ate used to desinate
the postion of tolerance zone.
Devisios aconting to
lables of fis in
(y.= V1000 mn)
209"
Devons according to
tables of fis in Jt
(Gy Vio an)
ites. 200-55
‘Shafts: small ours (6h sm) ae used vo designate the
Position of tolerance zoe
‘The numbers 0. 01,1,
16 decide he amount of tolerance and inden the rade of accuracy of hale in all 18 grades)
Grade
4
e( ) (sce )
us Us
0,01, 4 finer ge
FHI fin wo coae 1216 course ge.
Gauge
‘Machine building Rolling, castingWESTERMANN
TABLES
For the Metal Trade
Materials * Numerical Quantities * Forms
AEVISEO TO INDIAN STANDARDS:
REVISED SECOND. EDITION
Edited by
Hermann Jiitz
and
Eduard scharkus
NEW AGE INTERNATIONAL (P) LIMITED, PUBLISHERS
ior Wily Eatin Laie)
New Dei « Bangalore «Chennai» Cochin « Guwahati + Hyderabad
Jalandhar» Kolkata» Locknom » Mumbut Rane
Visit sat wowinewagepublishers comMaterials
Numbers
Mechani
Engineering Components
Metal Cutting Operations
Engineering Drawings
Index
‘Measures and Weights
Table of Contents
Section ONE
Section THREE
Section Four
Section Five
94-127
Section Six
128-147
148-150
151