Anda di halaman 1dari 104

ZEDPROG USER MANUAL

STANBUL ELEKTRONK ANAHTAR

Version 1.1

Istanbul, Turkey December 2009

CONTENTS

Page

1. Zed-Prog and Hardware Features.............................................................................3 2. Zed-Prog Usage............................................................................................................6 3. Zed-Prog Update.........................................................................................................8 4. Loading dump file to Pc software using Zed-Prog.................................................10 5. EEPROM and MCU Applications...........................................................................13 6. Zed-Prog EEPROM Applications............................................................................16 7. Zed-Prog Processor Applications.............................................................................64 8. Appendix......................................................................................................................99

1. Zed-Prog and Hardware Features


Zed-Prog:
Zed-Prog is a tool which can read most Eeproms and Processors without removing them from the circuit board. It does not need a PC connection to operate and is used with Zed-BULL transponder programmer. Zed-Prog can read most of the processors and the eeproms which the Zed-BULL has Eeprom applications for. Also most of the modules do not need to be removed. It can read the content of the eeprom or the processors with a help of test clip.

Zed-Prog Hardware:
Details of Zed-Prog hardware are listed below:

1. Update button 2. Communication status LEDs 3. Status LED 4. Clips connection socket 5. On/off button 6. Power in jack 7. Zed-Bull & Zed-Prog connection socket 8. Zed-Prog & PC connection socket (USB) 9. Zed-Bull & Zed-Prog connection cable 10. Zed-Bull connection tip 11. Zed-Prog connection tip 12. Zed-Bull & PC connection (USB) cable 13. PC connection tip 14. Zed-Prog connection tip 15. Zed-Prog EEPROM clips

Zed-Prog Hardware:

Zed-Prog Processor Clips (Pack 1 and Pack3) :

2. Zed-Prog Usage
Zed-Prog can only be used with Zed-BULL (ZB) transponder programming device. Hook up the ZB connections as shown below in figure 2.1 below.

Figure 2.1 Zed-Prog & Zed-Bull connection Warning 1: While making connections the ZB the On/off button should be in off position. Warning 2: To read chips without removal you must use a 9V-12V connection to Zed-Prog. The Zed-prog can be fed by Zed-BULL when hooked up for PC Connection. After Zed-Prog is connected to Zed-BULL and before turning on the Zed-Prog a test clip should be connected to a chip and read.

Figure 2.2 Connecting Clip to the chip Warning 3: Connect the ZedPROG with the unit turned off. If you make a connection when it is on, it may cause unwanted short circuits on the hardware and cause serious damages. The Zed-Prog eeprom test clips have 7 black and 1 red connection wires. The Red one represents the first Reader pin of the test clip. It should be aligned with the first pin of the Eeprom. This is usually indicated by a small indentation. The tip for finding this pin is explained in greater detail in each module description. Again with the processor clips first pin should be aligned with the red edge of the clip as shown above. After all connections are completed, it is safe to turn on the Zed-Prog. When Zed-Prog is turned on the status led will flash quickly. You should then select Zed-Prog in the menu on the Zed-BULL Screen. Then select the software pack and type of IC that is needed. The Zed-BULL screen will tell the user what to do in each step.

Figure 2.3 Choosing chip type in Zed-BULL menu

After the read process is completed, Zed-Prog should be turned off and the clip should be removed from the chip.

Important:
Most of the modules with eeprom can be read without removing the chip. But some of the modules can only be read with chip removed. This manual tells you which modules can be read on board and which modules have to be read with chip removed. Please see the explanations for each module. When reading the chips please follow the instruction exactly as it is described. Read the notes for each module carefully. Do not try to read the chips on board if it indicated they should be removed to be read.

3. Zed-Prog Update
When updating the Zed-Prog connect it to the computer via a USB cable. Make sure that unit is turned off and plug-in the Zed-Prog power adapter. The connection configuration is shown in figure 3.1 below

Figure 3.1 Zed-Prog power in and USB connection With the Zed-Prog button off, press and hold the Update button. Then turn the unit on and the status led should flash, Rx and TX LEDs will turn on and then turn off finally the status LED will turn on and will stay on. Now you can release your finger and Zed-Prog is in loader mode.

Open Zed-BULL software but do not click connect. Go to setting >> Module updates and choose Zed-Prog as the module.

Settings >> Update >> Module update

F Figure 3.2 Updating Zed-prog from Zed-BULL Software Choose Zed-prog as module. Click open file and choose the Zed-Prog update file with .zpp extension. Click update button, zed-prog will be updated.

Figure 3.3 Update steps

Figure 3.4 Update status screen After update process is completed the following screen will appear to show you have been successful with the update.

Figure 3.5 Update result information screen

4. Saving am EEPROM file to your PC using Zed-BULL PC Software


The Zed-Bull and Zed-Prog are all that is needed to do most EEPROM applications. However, one may need to copy the EEPROM data to the computer in certain situations. When this is the case the Zed-Prog should be turned-off after the EEPROM is read. Then the Zed-Prog should be connected to the computer via a USB cable. You must also connect the power adapter as shown in Figure 4.1.

Figure 4.1 Zed-Prog Power in jack and USB connection

Once the connections are done properly the Zed-Prog can be turned-on. After the device is powered, the status LED will start flashing rapidly. After the Zed-Prog configures itself the ZedBull software has to be opened. From the program select Extended Functions >> Zed-Prog.

Figure 4.2 choosing Zed-Prog from Zed-Bull Pc Software After clicking Zed-Prog, the following window will appear:

Figure 4.3 Zed-Prog Windows From the Zed-Prog window, select the EEPROM type from the left frame and click the READ button in Figure 4.4. EEPROM 24c02 is selected as an example. After clicking the READ button you should see a screen as in Figure 4.4. The EEPROM data is provided in the wide area on the right hand side while the EEPROM is read status notification will appear in the bottom left corner of the window.

10

Figure 4.4 Zed-Prog Window after a successful read. In order to save the read EEPROM file, select Save from the File menu. File >> Save

Figure 4.5 Saving File Once the Save option is selected a window will appear. The file is saved after the name and the directory is entered. It is vital that file extension is selected as .BIN

Figure 4.5 Saved file options 11

5. Zed-BULL EEPROM and MCU Applications


1 Opel immo2 - Siemens immobox 2 VW, Seat immo2 - Siemens immobox 3 VW, Seat immo3 - Valeo immobox 4 Fiat, Lancia, Citroen, Peugeot - Delphi immobox 5 Opel immo1 - Siemens immobox 6 Honda, Acura immobox 7 Honda, Rover - Valeo immobox 8 Fiat, Lancia - imm001.01 magneti marelli immobox 9 Fiat, Lancia - imm110.01 magneti marelli immobox 1 .Mercedes Sprinter, Vito, VW volt - Temic immobox 11 Fiat, Alfa Romeo, Lancia - magneti marelli BSI 12 Fiat, Citroen, Peugeot code2 - Delphi immobox 13 VW, Skoda, Seat immo1 - Siemens immobox 14 Fiat, Citroen, Peugeot, Iveco code3 - Magneti marelli BSI 15 Daihatsu - immobox 1998-2000 16 Renault, Dacia, Opel - Sagem immobox 17 Renault, Dacia - Siemens UCH 18 Fiat, Lancia, Alfa Romeo - Delphi BSI 19 Peugeot, Citroen, Valeo - immobox 20 Toyota, Daihatsu - immobox 1998-99 21 Volvo immo3 - Bosch immobox 22 Toyota - Bosch, Fujitsu ECU 23 Toyota, Rav4 - Denso, Fujitsu ECU 24 Toyota - immobox 25 Renault Laguna2 - Sagem UCH 26 Mercedes TIR - Temic ECU 27 Renault Megane2, Scenic2 - Siemens UCH 28 Alfa Romeo Code2 - Bosch immobox 29 Mitsubishi - Bosch immobox 30 BMW, Range Rover, Mini Cooper - EWS1 31 BMW, Range Rover, Mini Cooper - EWS2 32 BMW, Range Rover, Mini Cooper - EWS3 33 Iveco Daily, Iveco Truck - Bosch immobox 34 Renault - Valeo immobox 35 Alfa Romeo, Iveco - Bosch immobox 36 Suzuki - immobox 37 Toyota - ECU

12

38 Volvo, Mitsubishi - Bosch immobox 39 Toyota - Denso ECU 40 Nissan, Subaru - Siemens immobox 41 Peugeot motorbikes - Marelli immobox 42 Renault - Sagem UCH 43 Peugeot - Siemens BSI 44 Peugeot - Siemens BSI 45 Audi - Delphi immobox 46 Peugeot, Fiat, Lancia, Citroen - Texton immobox 47 Chrysler, Jeep, Dodge - SKIM immobox 48 Mazda, Ford - Temic immobox 49 Suzuki, Mitsubishi - immobox 50 Peugeot, Fiat, Citroen - immobox 51 Toyota - immobox 52 Nissan - Siemens immobox(NATS-4) 53 Volvo - Bosch immobox 54 Daewoo - immobox 55 Opel, Isuzu - immobox 56 Renault - Siemens immobox -98 57 Fiat - Delphi BSI 58 Ford - immobox 59 Ford - immobox 60 Mazda - Lucas immobox 61 Ford - Visteon Dashboard 62 Ford - Visteon ECU 63 Ford, Mazda - Siemens ECU 64 Fiat, Lancia - IMM100.01 Magneti Marelli immobox 65 Fiat - Siemens BSI 66 Renault - Siemens UCH 67 Acura immobox 68 BMW, Range Rover, Mini Cooper EWS4 69 Yamaha - Moric immobox 70 Renault, Opel - Sagem UCH 71 Opel, Isuzu - immobox 72 Suzuki - Denso immobox 73 Ducati bike - Magneti Marelli Dashboard immobox 74 Honda bike - immobox 75 Honda bike - immobox 76 Honda bike - immobox

13

Software Packages:
EEPROM PACK (STANDARD PACKAGE): All modules with Eeprom (Total 45 Modules)-Read all of them in circuit PACK 1: Module 8: Fiat, Lancia Magnetti Marelli -> Bravo (1998-2001), Marea (1998- ), Palio (-1999)Read on board. Module 50: Peugeot, Fiat, Citroen -> 306, Expert, Ranch- Read in circuit Module 51: Toyota -> Avensis- Read with chip removal

PACK 3: Module 5: Opel immo1- Siemens ->Astra F, Calibra, Combo B, Omega (1996-1999), Sintra (-1999), Tigra, Vectra B- Read with chip removal Module 7: Honda Rover Valeo -> Accord (-1999), Civic (-2001)-Read with chip removal Module 13: VW, Skoda, Seat immo1-Siemens -> Caddy (-1998, Golf 3, Passat 3, Polo3 (-1998), Transporter (-1998), Vento- Read in circuit Module 40: Nissan, Subaru Siemes -> Primer (-1998), Serena (-1998), Sunny, Terrano2 (-1998), Vannete (-1998)-Read with chip removal Module 44: Peugeot -Siemens BSI -> 2006 (1998-2001)-Read with chip removal Module 54: Daewoo -> Espero, Lanos (-2002), Leganza (-2000), Matiz (-2001), Nexia, Nubira (-2000)- Read with chip removal Module 56: Renault Siemens immobox-98 -> Megane (-1999), Twingo (-2000) - Read with chip removal Module 60: Mazda Lucas -> 323(-1999), 626(-1999), MX-5- Read with chip removal Module 66: Renault Siemens UCH -> Megane, Scenic- Read with chip removal

14

Zed-Prog EEPROM APPLICATIONS

15

Module 3:
VW, Seat immo3 - Valeo immobox

24c04 8 pins, 512 Bytes VW, SEAT ID: 44 Transponder Type: Blank PCF7935 Programmed transponder will start the vehicle

Note: Eeprom can be read on board in this module, but the free wire in the test clip should be short circuited to the Chrystal in the circuit board. Eeprom pins should be cleaned for good connection.

16

Module 4:
Fiat, Lancia, Citroen, Peugeot - Delphi immobox

93c46 8pins, 128 Bytes Fiat, Lancia, Citroen Jumper/Relay, Peugeot Boxer ID: 13 Transponder Type: T5 Programmed transponder will start the vehicle

Note: Eeprom can be read on board in this module. Eeprom pins should be cleaned for good conductivity.

17

Module 6:
Honda, Acura immobox

93c46 8pins, 128 Bytes Honda, Acura ID: 13 Transponder Type: T5 Programmed transponder will start the vehicle.

Note: Eeprom can be read on board in this module. Eeprom pins should be cleaned for good conductivity.

18

Module 12:
Fiat, Citroen, Peugeot code2 - Delphi immobox

93lc56b 8pins, 256 Bytes Fiat Ducato2,Citroen Jumper/Relay 2 ID: 48 Transponder Type: Megamos Crypto Programmed transponder and created image file will start the vehicle.

Note: Eeprom can be read on board in this module. Eeprom pins should be cleaned for good conductivity. 19

Module 14:
Fiat, Citroen, Peugeot, Iveco code3 - Magneti marelli BSI

95c160/95c320 8pin(SSOP), 2048/4096 Bytes Ducato3, Boxer3, Jumper3, Daily ID: 48 Transponder Type: Megamos Crypto Programmed transponder should be programmed into vehicle with a diagnostic tool with the calculated pin code.

Note: Eeprom can be read on board in this module. Eeprom pins should be cleaned for good conductivity.

20

Module 15:
Daihatsu - immobox 1998-2000

93lc66 8 pin(dip), 512 Bytes Daihatsu ID: 4C Transponder Type: JMA TPX1, Silca Electronic head Programmed transponder will start the vehicle

Note: Eeprom can be read on board in this module. Eeprom pins should be cleaned for good conductivity.

21

Module 16:
Renault, Dacia, Opel - Sagem immobox

93c46/93c56 8pin, 128/256 Bytes Dacia, Opel Movano, Renault master ID: 33 Transponder Type: T5 or PCF7930/31/35 Programmed transponder will start the vehicle

22

Note: Eeprom can be read on board in this module. Eeprom pins should be cleaned for good conductivity.

23

Module 17:
Renault, Dacia - Siemens UCH

93c66 8pin, 512 Bytes Clio, symbol, Logan, Sandero, Solenzo ID: 46 Transponder Type: Blank PCF7936 Programmed transponder has to be programmed into vehicle using a diagnostic tool with calculated pin code.

24

Module 18:
Fiat, Lancia, Alfa Romeo - Delphi BSI

93c66b 8pin, 512 Bytes Doblo, Albea, Alfa 156, Punto ID: 48 Transponder Type: Megamos Crypto Programmed transponder and created image file will start the vehicle.

Note: Eeprom can be read on board in this module. Eeprom pins should be cleaned for good conductivity. 25

Module 19:
Peugeot, Citroen, Valeo - immobox

93c46 8pin, 128 Bytes Berlingo, 406 ID: 33 Transponder Type: T5 or PCF7930/31/35 Programmed transponder will start the vehicle

Note: Eeprom can be read on board in this module. Eeprom pins should be cleaned for good conductivity. 26

Module 20:
Toyota, Daihatsu - immobox 1998-99

93c66 8pin, 512 Bytes Corolla, Camry, Hilux, Daihatsu ID: 4C Transponder Type: JMA TPX1, Silca Electronic head Programmed transponder will start the vehicle

27

28

Note: Eeprom can be read on board in this module. Eeprom pins should be cleaned for good conductivity.

29

Module 21:
Volvo immo3 - Bosch immobox

93c56/93c66 8pin, 256/512 Bytes cars and trucks ID: 44 Transponder Type: Blank PCF7935 Programmed transponder will start the vehicle

Note: Eeprom can be read on board in this module. Eeprom pins should be cleaned for good conductivity.

30

Module 22:
Toyota - Bosch, Fujitsu ECU

24c02/25020/25040 8pin, 256/256/512 Bytes Corolla, Yaris ID: 4C Transponder Type: JMA TPX1, Silca Electronic Head Programmed transponder will start the vehicle

31

Module 23:
Toyota, Rav4 - Denso, Fujitsu ECU

95080/93c86/25080 8pin, 1024/2048/1024 Bytes Corolla, Yaris, Camry ID: 4C Transponder Type: JMA TPX1, Silca Electronic Head Programmed transponder will start the vehicle

32

Module 24:
Toyota - immobox

24c04 8pin, 512 Bytes Corolla, Yaris, Camry ID: 4C Transponder Type: JMA TPX1, Silca Electronic head Programmed transponder will start the vehicle

Note: Eeprom can be read on board in this module, but the free wire in the test clip should be short circuited to the Chrystal in the circuit board as in the picture above. Eeprom pins should be cleaned for good conduction.

33

Module 26:
Mercedes truck - Temic ECU

93C56/93c66/93c86 8pin, 256/512/2048 Bytes Actros, Atego, Axor ID: 13 Transponder Type: T5 Programmed transponder will start the vehicle

34

Module 28:
Alfa Romeo Code2 - Bosch immobox

93c56 8pin, 256 Bytes 146 ID: 44 Transponder Type: Blank PCF7935 Programmed transponder will start the vehicle

35

Module 29:
Mitsubishi - Bosch immobox

93c56 8pin, 256 Bytes Carisma, Space Star ID: 44 Transponder Type: Blank PCF7935 Programmed transponder will start the vehicle

36

Module 33:
Iveco Daily, Iveco Truck - Bosch immobox

93c56 8pin, 256 Bytes Iveco Daily, Iveco Truck ID: 46 Transponder Type: Blank PCF7936 Programmed transponder should be programmed into the vehicle using a diagnostic tool with the calculated pin code

37

Module 34:
Renault - Valeo immobox

93c46 8pin, 128 Bytes Laguna1 ID: 33 Transponder Type: T5 or PCF7930/31/35 Programmed transponder will start the vehicle

38

Module 35:
Alfa Romeo, Iveco - Bosch immobox

93c46 8pin, 128 Bytes 145, Iveco ID: 33 Transponder Type: T5 or PCF7930/31/35 Programmed transponder will start the vehicle

39

Module 36:
Suzuki - immobox

93lc66 8pin, 512 Bytes Swift ID: 4C Transponder Type: JMA TPX1, Silca Electronic head Programmed transponder will start the vehicle

40

Module 37:
Toyota - ECU

25080/95080 8pin, 1024/1024 Bytes Corolla, Yaris ID: 4C Transponder Type: JMA TPX1, Silca Electronic head Programmed transponder will start the vehicle

Note: Eeprom can be read on board in this module. Eeprom pins should be cleaned for good conductivity. 41

Module 38:
Volvo, Mitsubishi - Bosch immobox

93c46 8pin, 128 Bytes Carisma ID: 33 Transponder Type: T5 or PCF7930/31/35 Programmed transponder will start the vehicle

Note: Eeprom can be read on board in this module, Eeprom pins should be cleaned for good conduction.

42

Module 39:
Toyota - Denso ECU

93c56 8pin, 256 Bytes Corolla ID: 4C Transponder Type: JMA TPX1, Silca Electronic head Programmed transponder will start the vehicle

43

Module 42:
Renault - Sagem UCH

93c66, 8pin, 512 Bytes Clio hb ID: 46 Transponder Type: Blank PCF7936 Programmed transponder should be programmed into the vehicle using a diagnostic tool with calculated pin code

44

Module 43:
Peugeot - Siemens BSI

93c66, 8pin, 512 Bytes 406 ID: 45 Transponder Type: Blank PCF7935 Programmed transponder will start the vehicle

45

Module 45:
Audi - Delphi immobox

93c46, 8pin, 128 Bytes Audi ID: 13 Transponder Type: T5 Programmed transponder will start the vehicle

46

Module 46:
Peugeot, Fiat, Lancia, Citroen - Texton immobox

93c66/95040, 8pin, 512 Bytes 306, Scudo ID: 33 Transponder Type: T5 or PCF7930/31/35 Programmed transponder will start the vehicle

47

Module 47:
Chrysler, Jeep, Dodge - SKIM immobox

Motorola MC68HC08AB16A(L72A)/MC68HC08AZ32(J66D)/24c02, 64pin/64pin/8pin, 512/512/256 Bytes

Chrysler, Jeep, Dodge ID: 64 Transponder Type: JMA TPX2, Silca Electronic head Programmed transponder will start the vehicle

48

Module 49:
Suzuki, Mitsubishi - immobox

24c01, 8pin, 128 Bytes Grandvitara, Lancer, Pacero, Galand ID: 4C Transponder Type: JMA TPX1, Silca Electronic head Programmed transponder will start the vehicle

49

Module 53:
Volvo - Bosch immobox

93C46, 8pin, 128 Bytes Volvo ID: 33 Transponder Type: T5 or PCF7930/31/35 Programmed transponder will start the vehicle

50

Module 55:
Opel, Isuzu - immobox

93c46, 8pin, 128 Bytes Frontera, Trooper ID: 13 Transponder Type: T5 Programmed transponder will start the vehicle

51

Module 57:
Fiat - Delphi BSI

93c86, 8pin, 2048 Bytes Grande Punto ID: 46 Transponder Type: Blank PCF7936 Programmed transponder should be programmed into the vehicle using a diagnostic tool with the calculated pin code

Note: Eeprom can be read on board in this module. Eeprom pins should be cleaned for good conductivity

52

Module 62:
Ford - Visteon ECU

95040, 8pin, 512 Bytes Focus, Fusion, Mondeo, Transit ID: 60 Transponder Type: JMA TPX2, Silca Electronic head Programmed transponder will start the vehicle

53

Module 63:
Ford, Mazda - Siemens ECU

93C56, 8pin, 256 Bytes Mazda2,Fiesta ID: 63 Transponder Tipi: JMA TPX2, Silca Electronic head Programmed transponder will start the vehicle

54

Module 67:
Acura - immobox

93C46, 8pin, 128 Bytes Acura ID: 13 Transponder Type: T5 Programmed transponder will start the vehicle

55

Module 69:
Yamaha - Moric immobox

Seiko S29190, 8pin, 128 Bytes Yamaha ID: 62 Transponder Type: JMA TPX2, Silca Electronic head Programmed transponder will start the vehicle

56

Module 70:
Renault, Opel - Sagem UCH

93c66, 8pin, 512 Bytes Vivaro, Movano, Kango, Trafic, Master ID: 46 Transponder Type: PCF7936 Calculated pin code can be used while programming transponder with a diagnostic tool

57

Module 71:
Opel, Isuzu - immobox

93C46, 8pin, 128 Bytes Frontera, Trooper ID: 48 Transponder Type: Megamos Crypto Programmed transponder and created image file will start the vehicle

Note: Eeprom can be read on board in this module. Eeprom pins should be cleaned for good conductivity

58

Module 72:
Suzuki - Denso immobox

93C66, 8pin, 512 Bytes Suzuki motorbike ID: 62 Transponder Type: JMA TPX2, Silca Electronic head Programmed transponder will start the vehicle

59

Module 73:
Ducati bike - Magneti Marelli Dashboard immobox

24c16,24c02, 8pin, 2048/256 Bytes Ducati motorbike ID: 11 Transponder Type: T5 Programmed transponder will start the vehicle

60

Module 74:
Honda bike - immobox

93c46, 8pin, 128 Bytes Honda motorbike ID: 46 Transponder Type: Blank Pcf7936 Programmed transponder and created image file will start the vehicle

61

Module 75:
Honda bike - immobox

93c56, 8pin, 128 Bytes Honda motorbike ID: 46 Transponder Type: Blank Pcf7936] Programmed transponder and created image file will start the vehicle

Note: Eeprom can be read on board in this module. Eeprom pins should be cleaned for good conductivity

62

Module 76:
Honda bike - immobox

93c66, 8pin, 128 Bytes Honda motorbike ID: 46 Transponder Type: Blank Pcf7936 Programmed transponder and created image file will start the vehicle

63

Zed-Prog MCU (PROCESSOR) APPLICATIONS

64

Module 1:
Opel immo2 - Siemens immobox

TMS370C702 28pin, 256 Bytes Agila, AstraG, Combo, CorsaC, Meriva, Omega, Sintra, VectraB, Tigra, Zafira ID: 40 Transponder Type: Blank PCF7935 Programmed transponder will start the vehicle

65

Module 2:
VW, Seat immo2 - Siemens immobox

TMS370C702 28pin, 256 Bytes VW,SEAT ID: 42 Transponder Type: Blank PCF7935 Programmed transponder will start the vehicle

66

Module 5:
Opel immo1 - Siemens immobox

Motorola MC68HC05B6(F10V-B91T-D33J) 52pin, 256 Bytes OPEL ID: 33 Transponder Type: T5 or PCF7930/31/35 Programmed transponder will start the vehicle

Processor Pack: PACK 3 This processor cannot be read on board. The Processor has to be removed and put to the clip. Please be careful with the direction and processor pins must be cleaned.

67

Module 7:
Honda, Rover - Valeo immobox

Motorola MC68HC05B6(F10V-B91T-D33J) 52pin, 256 Bytes Honda,Rover600 ID: 33 Transponder Type: T5 or PCF7930/31/35 Programmed transponder will start the vehicle

Processor Pack: PACK 3 This processor cannot be read on board. The Processor has to be removed and put to the clip. Please be careful with the direction and processor pins must be cleaned.

68

Module 8:
Fiat, Lancia - imm001.01 magneti marelli immobox

Motorola MC68HC05E6(F82B-G72G) 28pin, 160 Bytes Fiat, Lancia ID: 11 Transponder Type: T5 Programmed transponder will start the vehicle

MCU Pack: PACK 1 This module can be read on board with pack 1 clip. To read the chip on board first pin of the processor should be disconnected from the circuit board. To disconnect the pin, the resistor (#473 is written on it) should be removed from the circuit board; this resistor is located at the back side of the circuit board. Another option is to cut the line which continues through this resistor. Do not forget to put back the resistor, or re-connect the way which is cut, after completing the read process. The Processor can be read by removing it from the circuit board and putting it to the reader clip as well. Important: While putting the processor to the reader clip, Zed-Prog should be off. Be careful with the direction of the processor. Processor pins should be clean. See the figure below to see disconnecting the resistor from the board for on board reading.

69

70

Module 9:
Fiat, Lancia - imm110.01 magneti marelli immobox

Motorola MC68HC908AZ32(J66D) 64pin, 512 Bytes Fiat, Lancia ID: 11 Transponder Type: T5 Programmed transponder will start the vehicle

71

Module 10:
Mercedes Sprinter, Vito, VW volt - Temic immobox

Motorola MC68HC05X16(D62J)/AZ32(L52H-J66D) 64 pin, 256/512 Bytes Mercedes Sprinter, Vito, VW Volt ID: 12 Transponder Type: T5 Programmed transponder will start the vehicle

72

Module 11:
Fiat, Alfa Romeo, Lancia - magneti marelli BSI

Motorola MC68HC912DG128(3K91D)/MC9S12DP256(1K79X) 112pin, 2048/4096 Bytes Doblo, Albea, Alfa 156 ID: 48 Transponder Type: Megamos Crypto Programmed transponder will start the vehicle

73

Module 13:
VW, Skoda, Seat immo1 - Siemens immobox

Motorola MC68HC05B6(F10V-B91T-D33J) 52pin, 256 Bytes VW, Skoda, Seat ID: 33 Transponder Type: T5 or PCF7930/31/35 Programmed transponder will start the vehicle

MCU Pack: PACK 3 This processor can be read on board. Be careful with the direction of the processor. The processor pins should be clean.

74

Module 25:
Renault Laguna2 - Sagem UCH

Motorola MC68HC912DG128(3K91D)/MC9S12DP256(1K79X) 112pin, 2048/4096 Bytes Laguna2 ID: 46 Transponder Type: Laguna card The Calculated pin code can be used to program the card with a diagnostic tool.

75

Module 27:
Renault Megane2, Scenic2 - Siemens UCH

Motorola MC68HC912DG128(3K91D)/MC9S12DP256(1K79X) 112pin, 2048/4096 Bytes Megane2 ID: 46 Transponder Tipi: Megane card Calculated pin code can be used to program the card with a diagnostic tool.

76

Module 30:
BMW, Range Rover, Mini Cooper - EWS1

MC68HC11EA9(2D47J)(0D46J) 52pin, 512 Bytes BMW, Range Rover, Mini Cooper ID: 33 Rolling Transponder Type: Blank PCF7930/35 or remote key Programmed transponder will start the vehicle

77

Module 31:
BMW, Range Rover, Mini Cooper - EWS2

MC68HC11EA9(2D47J)(0D46J) 52pin, 512 Bytes BMW, Range Rover, Mini Cooper ID: 33 Rolling Transponder Type: Blank PCF7930/35 or remote key Programmed transponder will start the vehicle

78

Module 32:
BMW, Range Rover, Mini Cooper - EWS3

MC68HC11EA9(2D47J)(0D46J) 52pin, 512 Bytes BMW, Range Rover, Mini Cooper ID: 33 Rolling Transponder Type: Blank PCF7930/35 or remote key Programmed transponder will start the vehicle

79

Module 40:
Nissan, Subaru - Siemens immobox

Motorola MC68HC05B6(F10V-B91T-D33J), 52pin, 256 Bytes Nissan, Subaru ID: 33 Transponder Type: T5 or PCF7930/31/35 Programmed transponder will start the vehicle

MCU Pack: PACK 3 This processor CAN NOT BE READ ON BOARD. It has to be removed from the circuit board and put into the clip to read. Be careful with the direction of the processor. Processor pins should be cleaned.

80

Module 41:
Peugeot motorbike - Marelli immobox

Motorola MC68HC05B16(0D60J)-MC68HC05X16(0D62J), 64pin, 256 Bytes Peugeot bike, Piaggio bike ID: 11 Transponder Type: T5 Programmed transponder will start the vehicle

81

Module 44:
Peugeot - Siemens BSI

Motorola MC68HC05B16(F10V-B91T-D33J-D60J), 52pin, 256 Bytes 206 ID: 45 Transponder Type: Blank PCF7935 Programmed transponder will start the vehicle

MCU Pack: PACK 3 This processor CAN NOT BE READ ON BOARD. It has to be removed from the circuit board and put into the clip to read. Be careful with the direction of the processor. Processor pins should be cleaned

82

Module 47:
Chrysler, Jeep, Dodge - SKIM immobox

Motorola MC68HC08AB16A(L72A)/MC68HC08AZ32(J66D)/24c02, 64pin/64pin/8pin, 512/512/256 Bytes

Chrysler, Jeep, Dodge ID: 64 Transponder Type: JMA TPX2, Silca Electronic head Programmed transponder will start the vehicle.

83

Module 48:
Mazda, Ford - Temic immobox

Motorola MC68HC705P3(1F75B), 28pin, 128 Bytes 323, Probe ID: 12 Transponder Type: T5 Programmed transponder will start the vehicle

84

Module 50:
Peugeot, Fiat, Citroen - immobox

Motorola MC68HC05E6(F82B-G72G), 28pin, 160 Bytes 306 ID: 33 Transponder Type: T5 or PCF7930/31/35 Programmed transponder will start the vehicle

MCU Pack: PACK 1 This processor can be read on board. To read the chip on board, first pin of the processor should be disconnected from the circuit board. To disconnect first pin of the processor from the circuit board, the line to be cut is shown in figure below. Do not forget to reconnect the line after completing the process. The processor can be read by removing it from circuit board and putting to the reader clip.

Important: While putting the processor to the reader clip Zed-Prog should be off. Be careful with the direction of the processor. Processor pins should be clean. See the figure below to see which line should be cut from the circuit board to read the processor on board.

85

86

Module 51:
Toyota - immobox

Motorola MC68HC05E6(F82B-G72G), 28pin, 160 Bytes Avensis ID: 4C Transponder Type: JMA TPX1, Silca Electronic head Programmed transponder will start the vehicle

MCU Pack: PACK 1 The processor must be removed from circuit board. Then put the removed processor into the clip to read. Important: While reading the processor Zed-Prog should be off. Be careful with the direction of the processor. Processor pins must be cleaned.

87

Module 52:
Nissan - Siemens immobox (NATS-4)

TMS, 44pin, 256 Bytes Nissan ID: 41 Transponder Type: Blank PCF7935 Programmed transponder will start the vehicle

88

Module 54:
Daewoo - immobox

Motorola MC68HC05B6(F10V-B91T-D33J-D60J), 52pin, 256 Bytes Daewoo ID: 13 Transponder Type: T5 Programmed transponder will start the vehicle

MCU Pack: PACK 3 This processor cannot be read on board. The processor must be removed and put to the reader clip. Be careful with the direction of the processor. Processor pins should be cleaned.

89

Module 56:
Renault - Siemens immobox -98

Motorola MC68HC05B16(D54J)/MC68HC05B6(B83T), 52pin, 256/256 Bytes Megane ID: 33 Transponder Type: T5 or PCF7930/31/35 Programmed transponder will start the vehicle

MCU Pack: PACK 3 This processor CANNOT BE READ ON BOARD. It has to be removed from the circuit board and put into the clip to read. Be careful with the direction of the processor. Processor pins should be cleaned.

90

Module 58:
Ford - immobox

TMS370C702, 28pin, 256 Bytes Transit, KA ID: 4C Transponder Type: JMA TPX1, Silca Electronic head Programmed transponder will start the vehicle

91

Module 59:
Ford - immobox

TMS370C702, 28pin, 256 Bytes Transit, Mondeo ID: 4C Transponder Type: JMA TPX1, Silca Electronic head Programmed transponder will start the vehicle

92

Module 60:
Mazda - Lucas immobox

Motorola MC68HC05B6(F10V-B91T-D33J-D60J) 52pin, 256 Bytes 626 ID: 33 Transponder Type: T5 or PCF7930/31/35 Programmed transponder will start the vehicle

MCU Pack: PACK 3 This processor CANNOT BE READ ON BOARD. It has to be removed from the circuit board and put into the clip to read. Be careful with the direction of the processor. Processor pins should be cleaned

93

Module 61:
Ford - Visteon Dashboard

Motorola MC9s12H256(1K78X), 112pin, 4096 Bytes Focus, C-Max ID: 63 Transponder Type: JMA TPX2, Silca Electronic head Programmed transponder will start the vehicle

94

Module 64:
Fiat, Lancia - IMM100.01 Magneti marelli immobox

Motorola MC68HC908AZ32(J66D), 64pin, 512 Bytes Idea, Multipla, Lybra ID: 48 Transponder Type: Megamos Crypto Programmed transponder and created image file will start the vehicle

95

Module 65:
Fiat - Siemens BSI

Motorola

MC9S12DG128(L40K)/MC68HC912DG128(3K91D)/MC9S12DP256(1K79X)

112pin, 2048/2048/4096 Bytes


Panda ID: 46 Transponder Type: Blank PCF7936 Programmed transponder should be programmed into the vehicle using a diagnostic tool with the calculated pin code

96

Module 66:
Renault - Siemens UCH

Motorola MC68HC705B32(G96A-G41V-D59J), 52pin, 256 Bytes Megane, Scenic ID: 60-64 Transponder Type: JMA TPX2, Silca Electronic head Programmed transponder will start the vehicle

MCU Pack: PACK 3 This processor CANNOT BE READ ON BOARD. It has to be removed from the circuit board and put into the clip to read. Be careful with the direction of the processor. Processor pins should be cleaned

97

Module 68:
BMW, Range Rover, Mini Cooper - EWS4

Motorola MC9S12D64(2L86D), 80pin, 1024 Bytes BMW, Range Rover, Mini Cooper ID: 33 Rolling Transponder Type: Blank PCF7930/35 or remote key Programmed transponder will start the vehicle

98

APPENDIX:
Some of Motorola processors and matching mask numbers are given as below.

Motorola processors and Mask Numbers:


A75H B16B B19C B36T B46E B60R B65H B76T B83T B84N B91T B95T B96D B96T C11W C13W C14H C16J C16W C27B C28M C35N C40H C45A C47M C83W C85W C91F C92K C95K C96N D20J D26E MC68HC811A2 MC68HC805C4 MC68HC811E2 MC68HC805B6 MC68HC11A8 MC68HC11E9 MC68HC11A8 MC68HC11A8 MC68HC05B6 MC68HC11A1 MC68HC05B6 MC68HC11A8 MC68HC11A8 MC68HC05C8 MC68HC11A1 MC68HC11L6 MC68HC05B6 MC68HC811E2 MC68HC705C8 MC68HC11E9 MC68HC11G5FN1 MC68HC05B16 MC68HC05J1 XC68HC711D3 MC68HC711E9 MC68HC11E9 XC68HC711L6 MC68HC11E1 MC68HC05C12A MC68HC05E0 MC68HC11A1 MC68HC05B16 MC68HC11A8

99

D28J D33J D35E D37R D40J D40J D41V D45R D46J D47J D48J D53J D54E D54J D58J D59J D59J D60J D61N D62J D64J D67F D69F D69J D82R D86B D99H E11P E20T E20Y E22B E28B E31M E32B E41C E50H E53M E54F

MC68HC705B16 MC68HC05B6 MC68HC11E9 MC68HC05C12A MC68HC705B32 MC68HC705X32 XC68HC705BE12 MC68HC11ED0 MC68HC11A8 MC68HC11EA9 MC68HC11PH8 MC68HC05X32 MC68HC705P9 MC68HC05B16 MC68HC11PA8 MC68HC705B32 MC68HC705X32 MC68HC05B16 XC68HC711KA4 MC68HC05X16 MC68HC (7)11P2 MC68HC711K4 PC68HC711N4 MC68HC05X32 MC68HC11E9 MC68HC705J2 MC68HC711P2 MC68HC16Z2 MC68HC705C4A MC68HC705P6CP MC68HC11E20 MC68HC11E9 MC68HC705K1 MC68HC05C8 PC68HC916Y1 MC68HC05B16 MC68HC711P2 MC68HC16Z1

100

E57S E59B E61R E61W E62H E62W E69W E74J E75J E78C E79R E82K E88N F10V F10W F11N F12A F17V F23H F33P F37E F41E F41J F44T F49K F52E F53E F56K F62A F62J F63J F67V F68K F71L F73K F73T F88B F92J

MC68HC11KA4 MC68HC11KA4 MC68HC705C8 MC68HC705F8 MC68HC11K4 MC68HC16Z1 MC68HC16Z1 MC68HC11P2 MC68HC11K4 MC68HC05J1A MC68HC705C8A MC68HC11E20 MC68HC711KA2 MC68HC05B6 MC68HC705SR3 MC68HC11L6 MC68HC05J1A MC68HC11F1B4 MC68HC05P4A PC68HC16V1 MC68HC11F1 MC68HC05L28 MC68HC05L28 MC68HC705J1A MC68HC705C8A MC68HC11E32 MC68HC11KG4 MC68HC705B16 MC68HC05C8 MC68HC05B16 MC68HC705C9A MC68HC16Z1 MC68HC912D60 MC68HC05C8 or 705C8 MC68HC912D60 MC68HC16Z1 MC68HC705X4 MC68HCP11A1

101

F96J F97J F98Y G10V G11D G23V G26C G28F G32V G33P G35N G39Y G40G G41V G47V G49V G53F G54K G58F G59F G62K G63P G78M G96A G96Y H14A H19S H24M H42K H48T H50W H52P H54T H55B H55F H55W H56A H57A

MC68HC11E9 MC68HC11E9 MC68HC708AS48 MC68HC (7)11P2 MC68HC16Z2 MC68HC08AZ32 MC68HC16Z3 MC68HC05B16 MC68HC11KG4 XC68HC705P6ACP MC68HC05B16 MC68HC08AS20 MC68HC805K3 MC68HC705B32 MC68HC705X32 MC68HC08AZ32 MC68HC05J1A MC68HC05TB MC68HC705J1A MC68HC711E20 MC68HC708AS48 MC68HC705J1A MC68HC705V12 MC68HC705B32 MC68HC705V12 MC68HC708AS48 MC68HC711E20 MC68HC05V12 MC68HC705C8A XC68CM16Z1 MC68HC711E9 MC68HC705V12 MC68HC12BE32 MC68HC705BD9 MC68HC805K3 MC68HC912DG128 MC68HC08AZ32 MC68HC05H12

102

H62A H62P H70H H72J H86A H86X H91F H94K H95B H96J J20X J26R J27F J34P J35D J38M J54E J56W J61D J64Y J66D J66H J73R J74Y J79Y J88Y K00J K02S K03B K05W K07E K08B K08S K08W K11N K13J K20C K20R

MC68HC908AS60 or AZ60 MC68HC908AT32 MC68HC705SJ7 MC68HC705C8A MC68HC711KG2 MC68HC (7)11KG2 MC68HC912B32 MC68HC08AS20 MC68HC (7)11K4 MC68HC05JJ6 MC68HC908GP32 MC68HC08AS20 MC68HC08AS32 MC68HC12BE32 MC68HC08AZ60 MC68HC12BE32 MC68HC912B32 MMC2001 or 2003 MC68HC908AS60 MC68HC912B32 MC68HC08AZ32 MC68HC705J1A MC68HC705C8A MC68HC908AS60 MC68HC908BD48 MC68HC908JK3 MC68HC908RK2 MC68HC05P4A MC68HC705C9A MC68HC711D3 MC68HC11KS2 MC68HC705C8A MC68HC908GP32 MC68HC711KS2 MC68HC908LD64 MC68HC12D60 MC68HC705B16 MC68HC05PV8A

103

K22K K25E K36N K38K K39K K45D K45H K50E K54X K56G K59D K59H K75F K78X K79X K81H K85K K85V K91D L02H L05H L06H L09H L45J L51J L52H L53J L54J L69J L85D L87J

MMC2001 or 2003 MC68HC912BC32 MC9S12DP256 M68HC912D60 MC68HC908SR12 MC68HC908KX8 MC68HC908JB8 MC68HC912DG128 MC68HC711K4 MC68HC908AB32 MC68HC08JB8 PC527283MFU MC68HC912D60 MC9S12H256 MC9S12DP256 or A256 MC68HC711E9 MC68HC908AZ60A or AS60A MC68HC908AZ60A MC68HC912DG128 M68HC912D60 M68HC912DT128 MC68HC908SR12 MC68HC908KX8 or KX2 MC9S12C32 M68HC912D60 MC68HC08AZ32A MC68HC908GR8 MC68HC908MR32 or 16 MC68HC908QT1-4 or QY1-4 MC9S12A128 or DTB128 MC68HC908AZ60A or AS60A

104

Anda mungkin juga menyukai