Anda di halaman 1dari 2

1

3
Disclaimer: The information provided in this Brochure is only intended to give guidance in selecting and using Knauf products. While we make every effort to ensure its accuracy, neither PT Knauf Gypsum Indonesia nor any of its employees or affiliates warrant or assume any legal liability or responsibility for the completeness or usefulness of any information regarding any apparatus, product, or process described in this Brochure or for any failure in installing or constructing any structure, installation or building or part thereof, caused by using this Brochure. Readers are advised to independently verify this information prior to relying on it. In particular, readers must obtain appropriate independent advice on the use of products in specific structures, installations or buildings to ensure compliance with all regulations, including health and safety regulations.

Knauf Contact Technical Service : ) 021 - 789 1661 5 6


@ www.knauf.co.id

techteam@knauf.co.id

INSTALLATION PROCEDURE Perimeter Framing


1

Vertical Stud

stud. For doors weighing up to 50kg, fully boxed Knauf C Studs are used for the frame openings inserted with treated timber of 38mm thickness, cut to the size of the stud.

Studs should be positioned within the channels to coincide with the abutments of the boards, which will be fixed later. The centres (either 300, 400 or 600mm) depend on the performance requirements. Knauf C studs should be trimmed to within 5mm of internal channel. Knauf U Channels should be used for the head and base of partition and also to form any abutments and to frame openings. Bed each section on two continuous beads of Knauf Sealant and secure with Knauf Nailable Plug at maximum 600mm centres and 50mm from ends of channels or studs. Partitions should always run up to structural soffit. Where an existing suspended ceiling cannot be cut back to allow for partitioning, bracing must be provided for lateral support at the partition head.

Boarding

6 Metal Section 03/2011

All boards should be offered up to the frame with the face of board outwards and secured with Knauf Drywall Screws at 300mm centres. Fixing centres should be reduced to 200mm at corners. At head, foot and abutments board edges should be bedded on two continuous beads of Knauf Sealant. Board joints in multiple layers should be staggered both vertically and horizontally by at lleast 600mm.

Doorways

The head is formed with Knauf U Channel, bent back and screw fixed with Wafer Head Jackpoint Screws to the studs. For a lightweight door weighing up to 25kg, Knauf C Studs are used for the frame openings inserted with treated timber of 38mm thickness, cut to the size of the

KNAUF PARTITION SYSTEM


Partition Metal Sections are cold-rolled from high-grade galvanized steel in accordance with ASTM C645. A unique profile design and embossment, enhances the stiffness of the sections and makes for easy identifications on site.

PT. Knauf Gypsum Indonesia Cilandak Commercial Estate Garden Centre 5th Floor, Suite 16 (B) Jl. Raya Cilandak KKO Jakarta 12560, Indonesia

Knauf Hong Kong Ltd. Unit 606A, Island Place Tower, 510 Kings Road, North Point, Hong Kong

Phone: (+62 21) 789 1661 Fax: (+62 21) 789 1662

Tel. : (852)2964-9311 Fax. : (852)2964-9313

Knauf Singapore Pte Ltd 80 Marine Parade Rd #14 - 06 Parkway Parade Singapore 449269

Tel. : (+65) 6345 9233 Fax. : (+65) 6345 5465

Website : www.knauf.co.id, e-mail : techteam@knauf.co.id

E-mail : enquiry@knauf.com.hk

E-mail : enquiry@knauf.com.sg Website : www.knauf.com.sg

Knauf Partition Metal - Standard Partition


Head track Knauf U Channel secure to soffit.

Features
Compatible with Knauf plasterboards

Knauf C Stud
Galvanised lightweight steel section for use in non-load bearing partition systems. Estimating guide : 1.67 m per m2 partition (based on 600mm centres).
Dimension (mm) gauge size/web (A) 50 0.50 75 length 2700 3000 3600 2700 3000 3600 flange (B) 32/34 Pack Details lengths per pack 10 10 10 10 10 10 kg/pack () 14.17 15.74 18.89 16.74 18.82 22.58
B A

to form high performance partition systems. Suitable to be used for both commercial partitions. Versatile product to form partition systems to meet wide ranging performance requirements. Unique stamping on sections for added strength and easy identification. Fast installation. and residential

Taped & jointed Seamless finish.

Door head Knauf U Channel snipped, bent back and screwed to the studs. Timber ground (full height) to door frame.

32/34

Knauf U Channel
Galvanised steel section for use as the standard head and floor track for partitions. Estimating guide : 2 m per metre run partition. Head & floor track.
Dimension (mm) gauge size/web (A) 50 75 50 75 length 3000 3000 3000 3000 flange (B) 25 25 25 25 lengths per pack 10 10 10 10

Use
Framing for Knauf Partition Systems
B A

Studs Knauf C Stud with triangle embossment engaged in Plasterboard lining Fixed to metal framework with Knauf Drywall screw.

Performance
Knauf Partition Metal sections refer to ASTM C645.

Pack Details kg/pack () 15.38 15.38 12.30 12.30

0.50

Floor track Knauf U Channel secured to floor.

0.40

DIMENSION (mm) Board thickness Number of layer Stud size & gauge Overall width

FIRE RESISTANCE Fireshield, Denseshield (hours) Weigth (kg/m2) **

Office accommodation Stud centres (mm)


300 400 600 300 boxed 400 boxed 600 boxed 300

Max. Heights - Medium Duty

Public circulation & Industrial Areas Stud centres (mm)


400 600 300 boxed 400 boxed 600 boxed

Max. Heights - Heavy Duty

Major circulation & Heavy Industrial areas Stud centres (mm)


300 400 600 300 boxed 400 boxed 600 boxed

Max. Heights - Severe Duty

1 2 3 4 5 6 7 8

12 15 12 15 12 15 12 15
3

1 2

74 50 (0.50) 80 98 110 99 75 (0.50) 105 123 135

0.5 1 2 2 0.5 1 2 2

18 22 35 42 18 22 35 42

1 2 3 4 5 6 7 8

4190 4580 4780 5260 5160 5650 5650 6130

3500 3600 4190 4580 4280 4770 4870 5360

3110 3110 3700 3890 3890 4280 4280 4570

4870 5350 5550 6230 6140 6620 6620 7300

4180 4570 4870 5350 5000 5550 5740 6330

3600 3890 4380 4770 4570 4960 4960 5450

3800 4190 4400 4800 4700 5200 5200 5700

3220 3310 3800 4100 3900 4300 4500 4900

2820 2820 3400 3500 3700 3900 3900 4300

4480 4870 5100 5600 5500 6100 6100 6700

3800 4190 4400 4900 4600 5100 5200 5800

3310 3600 4000 4400 4200 4600 4600 5000

3310 3700 3800 4200 4100 4500 4500 4900

2820 2820 3300 3800 3400 3800 3900 4300

2430 2600 3000 3100 3100 3400 3400 3700

3890 4300 4500 4900 4800 5300 5300 5800

3310 3700 3900 4200 4000 4400 4600 5000

2820 3100 3500 3800 3600 4000 4000 4400

1 2

* 25mm, 20kg/m insulation quilt should be used. ** System weights based on Knauf Standardboard *** Fire resistances shown are in accordance with SNI 03-1741 and ASTM E119.

Anda mungkin juga menyukai