Anda di halaman 1dari 57

Service Manual

DEH-1450/XM/ES

ORDER NO.

CRT2756

HIGH POWER CD PLAYER WITH FM/AM TUNER

DEH-1450 DEH-1450B
XM/ES
- This service manual should be used together with the following manual(s):
Model No. CX-977 Order No. CRT2624

XM/ES

Mech. Module Remarks S9 CD Mech. Module:Circuit Description, Mech.Description, Disassembly

CONTENTS
1. 2. 3. 4. 5. 6. SAFETY INFORMATION ............................................2 EXPLODED VIEWS AND PARTS LIST .......................2 BLOCK DIAGRAM AND SCHEMATIC DIAGRAM .....8 PCB CONNECTION DIAGRAM ................................22 ELECTRICAL PARTS LIST ........................................30 ADJUSTMENT..........................................................34 7. GENERAL INFORMATION .......................................38 7.1 DIAGNOSIS ........................................................38 7.1.1 DISASSEMBLY .........................................38 7.1.2 CONNECTOR FUNCTION DESCRIPTION .......41 7.2 PARTS .................................................................42 7.2.1 IC................................................................42 7.2.2 DISPLAY ....................................................50 7.3 OPERATIONAL FLOW CHART ...........................51 8. OPERATIONS AND SPECIFICATIONS.....................52

PIONEER CORPORATION

4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O.Box 1760, Long Beach, CA 90801-1760 U.S.A. PIONEER EUROPE NV Haven 1087 Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE.LTD. 253 Alexandra Road, #04-01, Singapore 159936

C PIONEER CORPORATION 2001

K-ZZD. OCT. 2001 Printed in Japan

DEH-1450,1450B

- CD Player Service Precautions


1. For pickup unit(CXX1480) handling, please refer to"Disassembly"(see page 38). During replacement, handling precautions shall be taken to prevent an electrostatic discharge(protection by a jumper-solder). 2. During disassembly, be sure to turn the power off since an internal IC might be destroyed when a connector is plugged or unplugged. 3. Please checking the grating after changing the pickup unit(see page 35). 4. In this product, because the memory capacity of the microcomputer is insufficient, the test mode is not installed. However grating of the pickup unit can be confirmed.

1. SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician.

2. EXPLODED VIEWS AND PARTS LIST


2.1 PACKING
6 4 8 2 9 7 14 16 1 11 5 3

15 10

13

12

DEH-1450,1450B

NOTE:
- Parts marked by * are generally unavailable because they are not in our Master Spare Parts List. - Screws adjacent to mark on the product are used for disassembly.

(1) PACKING SECTION PARTS LIST


Mark No. Description 1 2 3 4 5 6 7 8 9 10 Cord Assy Spring Screw Polyethylene Bag Screw Screw Polyethylene Bag Handle Bush Polyethylene Bag Part No. CDE6468 CBH1650 CBA1002 CEG-127 CRZ50P090FMC TRZ50P080FMC CEG-158 CNC5395 CNV3930 CEG-162 Mark No. Description 11-1 11-2 12 13 14 Owners Manual Installation Manual Carton Contain Box Protector Part No. CRD3488 CRD3493
See Contrast table(2) See Contrast table(2)

CHP2421 CHP2422 CXB3520

15 Protector 16 Case Assy

(2) CONTRAST TABLE DEH-1450/XM/ES and DEH-1450B/XM/ES are constructed the same except for the following:
Mark No. Symbol and Description DEH-1450/XM/ES 12 Carton CHG4487 13 Contain Box CHL4487 Part No. DEH-1450B/XM/ES CHG4490 CHL4490

- Owner's Manual, Installation Manual


Model DEH-1450/XM/ES DEH-1450B/XM/ES Part No. CRD3488 CRD3493 Language English, Spanish, Portuguese(B), Chinese, Arabic

DEH-1450,1450B

2.2 EXTERIOR

B A

DEH-1450,1450B

(1) EXTERIOR SECTION PARTS LIST


Mark No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Screw Screw Screw Cord Assy Cable Fuse
CD Mechanism Module(S9ANA)

Part No. BMZ30P100FMC BSZ26P060FMC BSZ30P060FMC CDE6468

Mark No. Description 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 Button(VOL+,-) Button(SRC) Button(EJECT) Button(CLOCK) Button(A,LD) Button(1-6) Spring Cover Keyboard Unit LCD Connector(CN1800) Holder Sheet Lighting Conductor Connector Lighting Conductor Rubber Grille Unit Button Spring Spring Spring Bracket Holder Cover Panel Arm Arm Arm Screw Screw IC(IC361) Transistor(Q501,910) Sheet Panel

Part No. CAC7182 CAC7187 CAC7183 CAC7298 CAC7184 CAC7180 CBH2210 CNS6720
See Contrast table(2) See Contrast table(2)

Case(10A) Holder Cushion Insulator Tuner Amp Unit Screw Screw Screw FM/AM Tuner Unit Holder Pin Jack(CN351) Terminal(CN404) Plug(CN901) Connector(CN751) Connector(CN501) Antenna Jack(CN402) Holder Holder Insulator Heat Sink Holder Unit Chassis Unit Detach Grille Assy Screw Button(DETACH) Button(EQ) Button(SELECT)

CDE6610 CEK1136 CXK5501 CNB2686 CNC5704 CNM4870 CNM7622 CWM7944 ASZ26P060FMC BPZ26P120FMC BSZ26P160FMC CWE1563 CNC8815 CKB1035 CKF1059 CKM1330 CKS3581 CKS3835 CKX1056 CNC8615 CNC9619 CNM6949 CNR1583 CXB6681 CXB7816
See Contrast table(2)

CKS3580 CNC9617 CNM7057 CNV6476 CNV6868 CNV6869 CNV6905


See Contrast table(2)

CAC4836 CBH1835 CBH2208 CBH2367 CNC6791 CNC8042 CNM6276 CNS6722 CNV4692 CNV4728 CNV5576 IMS20P030FZK ISS26P055FUC TDA7386 2SD2396
See Contrast table(2)

BPZ20P100FZK CAC5789 CAC7186 CAC7181

CNS6344

(2) CONTRAST TABLE DEH-1450/XM/ES and DEH-1450B/XM/ES are constructed the same except for the following:
Part No. DEH-1450B/XM/ES CXB8038 CWM7958 CAW1688 CXB8054 CNM7294

Mark No. 31 44 45 53 69

Symbol and Description Detach Grille Assy Keyboard Unit LCD Grille Unit Sheet

DEH-1450/XM/ES CXB8036 CWM7957 CAW1723 CXB8052 Not used

DEH-1450,1450B

2.3 CD MECHANISM MODULE

DEH-1450,1450B

- CD MECHANISM MODULE SECTION PARTS LIST


Mark No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 Control Unit Connector(CN701) Connector(CN101) Screw Screw Screw(M2x4) Screw(M2x3) Screw Washer Washer Washer Washer Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Shaft Roller Frame Lever Lever Arm Arm Arm Bracket Frame Belt Gear Gear Gear Gear Gear Part No. CWX2481 CKS1959 CKS3486 BMZ20P025FMC BSZ20P040FMC CBA1362 CBA1527 CBA1545 CBF1037 CBF1038 CBF1039 CBF1060 CBH2378 CBH2379 CBH2514 CBH2533 CBH2382 CBH2383 CBH2384 CBH2527 CBH2386 CBH2537 CBH2390 CBH2391 CBH2523 CBH2426 CBH2444 CBL1561 CBL1553 CLA3845 CLA3910 CNC9654 CNC9664 CNC8949 CNC9661 CNC9016 CNC9017 CNC9123 CNC9656 CNT1086 CNV6886 CNV6316 CNV6317 CNV6318 CNV6319 Mark No. Description 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 Gear Arm Arm Arm Arm Arm Guide Arm Guide Rack Clamper Arm Guide Cover Arm Guide Roller Damper Damper Guide Chassis Unit Arm Unit Arm Unit Arm Unit Motor Unit(M2) Screw Unit Gear Unit Bracket Unit Motor Unit(M1) Arm Unit Screw(M2x5) Screw Screw Washer Washer Pickup Unit(Service)(P9) Screw Guide Roller Spring Part No. CNV6320 CNV6322 CNV6323 CNV6324 CNV6888 CNV6889 CNV6327 CNV6924 CNV6921 CNV6923 CNV6331 CNV6332 CNV6333 CNV6334 CNV6335 CNV6336 CNV6338 CNV6339 CNV6340 CNV6925 CXB7980 CXB7983 CXB7984 CXB7985 CXB5903 CXB5904 CXB8076 CXB7982 CXB6007 CXB8504 EBA1028 JFZ20P020FMC JGZ17P020FZK YE15FUC YE20FUC CXX1480 IMS26P030FMC CNV6922 CNV6887 CBH2509 CBH2512 CBH2536 CNV6906

86 Spring 87 Spring 88 Collar

DEH-1450,1450B

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM


3.1 BLOCK DIAGRAM

A TUNER AMP UNIT


A
FM/AM TUNER UNIT
ANTENNA CN402 28 AMANT

AMRF ATT

FM/AM 1ST IF 10.7MHz T51 Q51 CF51 CF52 CF53

MPXREF 41kHz AMDET

IC 2 FM MPX

L ch 6 R ch 5

ANT ADJ
FMANT

IC1 MIXER, IF AMP, DET.


FMRF CF202

COMP LDET

21 18

27 RFGND 26

ATT

IMG ADJ AM 2ND IF X901 450kHz 10.25MHz


WC NC NC

IC 3 EEPROM
FMLOCL STIND SDBW DGND FMSD DI/DO NL1 NL2 CE2 CE1

76

NC

CK

LOCH 23 25

LOCL

SL

RF ADJ Q410

CREQ

VDD VCC

14 PCE1 PCK PCE2 PDIO 13 48 12 11 57

7 17 20 22 10 19 14 PDIO

24

11 12 15 16 PCE2 PCE1 PCK

13 SL

2 SD

LOCL

VCC

VDD

PICKUP UNIT (SERVICE)(P9)


LASER DIODE LDMD

C CONTROL UNIT
CN101 Q101
15 5 AC,BD F,E FO+ TO+ LD+ 4 1 14 FOP TOP VDD 9 8 LDO MDI RFRPIN FEO 24 16 38 43 46 RFI FEI TEI L_OUT 85 78

CN701
L-OUT

CN501
14 14
CDL

HOLOGRAM UNIT FOCUS ACT. MONITOR TRACKING ACT. DIODE

TEO 14

RF-AMP

IC 101 TA2153FN
12 FOP 14 TOP TD/FD SD/MD

SERVO CONTROL, DSP, LPF, DAC

79

IC 201 TC9495F2

SPINDLE MOTOR

CD DRIVER
16 SOP 15 SOM 17 LCOP 18 LCOM

LOAD/ CARRIAGE MOTOR

LOEJ MUTE

22 9

LOEJ CONT

10 11

10 11

LOEJ CONT

34 23

IC 401 BA5996FM
DSCSNS HOME

17 16

17 16

79 32

S901 HOME VD 12EJ DISC CLAMP SENSE 8EJ SENSE SENSE SENSE VDD

Q510
VD

2 VD

B.U

+5V REGULATOR
4

IC 701 BA05SFP
1

Q511
CD5VON
CD5VON

VDCONT

21

35

8 1 2 3 4

DEH-1450,1450B

CN351
REAR L CH Q 351

SYSTEM CONTROLLER IC 610 (1/2) PE5262A


6 76

Q359

VDD REGULATOR
SD SL VDD

Q913
B.U

14 PCE1 PCK PCE2 PDIO 13 48 12 11 57

TUNPCE TUNPCK TUNPCE2 TUNPDO TUNPDI LOCL VST VCK VDT VCC SYSPW

VCC REGULATOR
Q910 Q911
B.U

CN901
B.U BACKUP 2 FUSE 10A

Q912

B
2 BACK UP GND 1

IN2_L

VST/ VCK/ VDT

POWER AMP
23 FLFL+ RLRL+ 10 11

ELECTRONIC VOLUME
3 IN3_L

10 12 9 11

10 12 9 11

IC 301 PML003AM

Frontout_L Rearout_L

14

FL 12 RL

IC 361 TDA7386
MUTE 22 STBY 4

21 3 5

FL FL+ RLRL+

ANTPW

SYSPW

Q921

Q361 MUTE

Q920
asens bsens ACC 3 B.U 3 ACC

ASENS

64

BSENS

63

ANTIN

52

TELIN

38

C
6

34 23

SYSPW LOEJ CONT

42

B.REMOTE IC 901 TPD1018F

B.REM

6 B.REM

MUTE 79 32 DSCSNS HOME

44

B
CN751 IC 610(2/2) PE5262A
KYDT 8 9 KYDT DPDT 3 4 3 4

KEYBOARD UNIT

SYSTEM CONTROLLER

CN1800 KEY CONTROLLER LCD DRIVER


20 18 KYDT DPDT

21

VDCONT

DPDT

RESET

60 VDD

RESET IC 603 S-80834ANY

LCD

VDD

SW5V

56

VDD

SWVDD 35 CD5VON

41

10 VLCD

Q750

IC 1800 PD6340A KEY MATRIX

9 5 6 7 8

DEH-1450,1450B

3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)


Note: When ordering service parts, be sure to refer to EXPLODED VIEWS AND PARTS LIST or ELECTRICAL PARTS LIST.

A
A-a A-b

A-a
Large size SCH diagram
A-a A-b

Guide page

272

A-a

A-b

Detailed page
272 162 183 183 162

FM(100%):-19.5dBs AM(30%):-30dBs

ELECTRONIC

FM/AM TUNER UNIT

R791 0R0

FMLOCL

SYST
ANTENNA JACK
CSS1023 4.194304MHz 682

CONTROL UNIT

NOTE : Symbol indicates a resistor. No differentiation is made between chip resistors and discrete resistors. Symbol indicates a capacitor. No differentiation is made between chip capacitors and discrete capacitors. The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. For resistors and capacitors in the circuit diagrams, their resistance values or capacitance values are expressed in codes: Ex. *Resistors Code Practical value 123 12k ohms 103 10k ohms *Capacitors Code Practical value 103 0.01F 101/10 100F/10V

10

A
1

CN1800

104

104

DEH-1450,1450B

A-b
A TUNER AMP UNIT

VOLUME

FM(100%):+3.6dBs AM(30%):-6.9dBs CD:+10.2dBs

CD:+9.4dBs

PRE OUT
RR

MUTE

RL

EM CONTROLLER

POWER AMP
FM(100%):+29.6dBs AM(30%):+19.1dBs CD:+36.2dBs

CEK1136

>

10A

BACK UP GND ACC

C
B.REM

VDD REGULATOR

RLFLRL+ FL+ RRFR-

VCC REGULATOR SYS+B REGULATOR

RR+ FR+

BACK UP SENSE

ACC SENSE

B.REMOTE

11

183

183 272 272

162

162

CSS1023 4.194304MHz

ELECTRONIC VOLU

DEH-1450,1450B

ANTENNA JACK
682

FM/AM TUNER UNIT


FMLOCL

FM(100%):-19.5dBs AM(30%):-30dBs

12

A-a

2
R791

3
0R0

SYSTEM CO

A-a A-b

104

104

CONTROL UNIT

2 3

4
6

5 6

NOTE : Symbol indicates a resistor. No differentiation is made between chip resistors and discrete resistors. Symbol indicates a capacitor. No differentiation is made between chip capacitors and discrete capacitors.

The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation.

For resistors and capacitors in the circuit diagrams, their resistance values or capacitance values are expressed in codes:

7 C

Ex. *Resistors Code Practical value 123 12k ohms 103 10k ohms

*Capacitors Code Practical value 103 0.01F 101/10 100F/10V

CN1800

DEH-1450,1450B

A-a
B

13 A

A-a A-b

B A

D C

14

A-a A-b

DEH-1450,1450B

A-b
A TUNER AMP UNIT
FM(100%):+3.6dBs AM(30%):-6.9dBs CD:+10.2dBs CD:+9.4dBs

1
PRE OUT
RR

C VOLUME

MUTE

RL

EM CONTROLLER

POWER AMP
FM(100%):+29.6dBs AM(30%):+19.1dBs CD:+36 2dBs

FM(100%):+29.6dBs AM(30%):+19.1dBs CD:+36.2dBs

CEK1136

>

10A

BACK UP GND ACC

5
B.REM

3
VDD REGULATOR
RLFLRL+ FL+ RRFR-

VCC REGULATOR SYS+B REGULATOR

RR+ FR+

5
BACK UP SENSE

6
ACC SENSE

B.REMOTE

DEH-1450,1450B

A-b
A-a A-b
A B C

15

DEH-1450,1450B

3.3 KEYBOARD UNIT


A

KEYBOARD UNIT

LCD DRIVER

LCD

16

B
1 2

DEH-1450,1450B

A
CN751

IL1700,1701:14V 40mA

CLOCK

LOC/BSM

D1702-1708 IL1700,1701 LCD R1711 R1715,1719

DEH-1450/XM/ES SML-310PT CEL1651 CAW1723 820 121

DEH-1450B/XM/ES SML-310VT CEL1662 CAW1688 121 181

B
5 6 7 8

17

DEH-1450,1450B

3.4 CD MECHANISM MODULE

CONTROL UNIT

PICKUP UNIT(SERVICE)(P9)

RF AMP

CN101

ACT/MOTOR DRIVER

SPINDLE M1 CXB6007 LOADING/CARRIAGE M2 CXB5903

5V REGULATOR
18

C
1 2

DEH-1450,1450B

SERVO CONTROL/DSP/DAC/LPF

16.934MHz

ER

SWITCHES: CONTROL UNIT S901 : HOME SWITCH.....ON-OFF S902 : CLAMP SWITCH....ON-OFF S903 : DSCSNS SWITCH....ON-OFF S904 : 12EJ SWITCH....ON-OFF S905 : 8EJ SWITCH....ON-OFF The underlined indicates the switch position.
Decimal points for resistor and capacitor fixed values are expressed as : 2.22R2 0.022R022

CN701

A
CN501
D

C
5 6 7 8

19

DEH-1450,1450B
Note:1. The encircled numbers denote measuring pointes in the circuit diagram. 2. Reference voltage VREF:2.1V

- Waveforms
1 2 3 4 CH1:DSCSNS 5V/div. CH2:CLCONT 5V/div. 500ms/div. CH3:LOEJ 5V/div. CH4:VD 10V/div. When loading (12 cm CD) 1 2 3 4 5 CH1:FD 500mV/div. CH1:DSCSNS 5V/div. 6 CH2:FOK 5V/div. 500ms/div. CH2:CLCONT 5V/div. 500ms/div. 7 CH3:MD 5V/div. CH3:LOEJ 5V/div. CH4:VD 10V/div. When setting up "Source On" When loading (8 cm CD) Ref. : VREF Mode : Normal

Ref. : GND Mode : Normal

Ref. : GND Mode : Normal

5 CH1:FD 6 CH2:FOK 7 CH3:MD

500mV/div. 5V/div. 100ms/div. 5V/div.

8 CH1:FE 500mV/div. 500ms/div. 9 CH2:FOON 5V/div. When setting up "Source On"

0 CH1:TE 8 CH2:FE

500mV/div. 200ms/div. 500mV/div.

When setting up "Source On"

Magnified drawing for "time"

Ref. : VREF Mode : Normal

Ref. : VREF Mode : Normal

Ref. : VREF Mode : Normal

8 5 0 !

CH1:FE 500mV/div. CH2:FD 500mV/div. CH3:TE 500mV/div. CH4:TD 500mV/div. During "Play"

@ CH1:BCK 1ms/div.

2V/div.

1s/div. # CH1:LRCK 2V/div. $ CH2:DOUT 2V/div. During "Play"

10s/div.

During "Play"

Ref. : VREF Mode : Normal

Ref. : VREF Mode : Normal

Ref. : VREF Mode : Normal

7 CH1:MD

500mV/div.

10s/div. % CH1:RFO

During "Play"

500mV/div. 500mV/div. 0.5s/div. % CH1:RFO 0 CH2:TE 500mV/div. During "Play" During "Tracking Open"

2ms/div.

Ref. : VREF Mode : Normal

Ref. : VREF Mode : Normal

Ref. : VREF Mode : Test

20

DEH-1450,1450B

5 CH1:FD ^ CH2:FOP

1V/div. 2V/div.

200ms/div.

% CH1:RFO 0 CH2:TE ! CH3:TD

% CH1:RFO 1V/div. 500mV/div. 500s/div. 0 CH2:TE ! CH3:TD 1V/div.

1V/div. 1V/div. 1V/div.

5ms/div.

With no disk inserted During "Focus Close"

1 Track Jump

32 Track Jump

Ref. : VREF Mode : Test

Ref. : VREF Mode : Test

Ref. : VREF Mode : Test

% CH1:RFO 0 CH2:TE ! CH3:TD

1V/div. 1V/div. 1V/div.

% 5ms/div. & 5 !

CH1:RFO CH2:DFCT CH3:FD CH4:TD

2V/div. 5V/div. 1V/div. 2V/div.

% CH1:RFO 500s/div. 0 CH2:TE & CH3:DFCT

1V/div. 500mV/div. 200ms/div. 5V/div.

100 Track Jump

When reproducing black dots (800m)

During inside/outside search

Ref. : VREF Mode : Test

Ref. : VREF Mode : Normal

Ref. : VREF Mode : Normal

* CH1:TEY ( CH2:SD

500mV/div. 200ms/div. 2V/div.

1 CH1:DSCSNS 2 CH2:CLCONT 3 CH3:LOEJ

1 CH1:DSCSNS 5V/div. 5V/div. 200ms/div. 2 CH2:CLCONT 3 CH3:LOEJ 5V/div.

5V/div. 5V/div. 200ms/div. 5V/div.

During inside/outside search When "Eject" (12 cm CD) When "Eject" (8cm CD)

Ref. : VREF Mode : Normal

Ref. : GND Mode : Normal

Ref. : GND Mode : Normal

) CH1:LOUT 2V/div. CH2:ROUT 2V/div. "Play" in 1kHz, 0dB

200s/div.

Ref. : GND Mode : Normal

21

DEH-1450,1450B

4. PCB CONNECTION DIAGRAM


4.1 TUNER AMP UNIT
A

A TUNER AMP UNIT

CORD ASSY

NOTE FOR PCB DIAGRAMS


1. The parts mounted on this PCB include all necessary parts for several destination. For further information for respective destinations, be sure to check
Connector Capacitor
2 1 3 4 5 6 7 8 9 10 11 12 13 14 15 16

SIDE A
B
P.C.Board Chip Part

SIDE B

C
CN701

22

A
1

A
2 3 4

DEH-1450,1450B

SY

SIDE A
A

5 6 7

1 2 3

ANTENNA JACK

FM/AM TUNER UNIT

B
5

CN1800

FRONT
6 7

A
8

23

DEH-1450,1450B

A TUNER AMP UNIT


A

1 3

6 4

1 3

6 4

4 6

3 1

24

AA
1

DEH-1450,1450B

SIDE B
A

4 3 6 1

4 6

3 1

4 6

3 1

AA
8

25

DEH-1450,1450B

4.2 KEYBOARD UNIT


SIDE A
A

SIDE B

KEYBOARD UNIT

B
LOUD

KEYBOARD UNIT

AUDIO

EJECT

LCD

LOC/BSM

BAND

VOL+

D CLOCK

26

B
1 2

EQ

VOL-

SOURCE

A
CN751

DEH-1450,1450B

27

B A

D C

28

DEH-1450,1450B

M2 LOADING/CARRIAGE MOTOR
HOME

CONTROL UNIT

C
PICKUP UNIT(SERVICE)(P9) M1 SPINDLE MOTOR
VREF 12EJ DSCSNS

4.3 CD MECHANISM MODULE

CN501

SIDE A

DEH-1450,1450B

CONTROL UNIT
8EJ

SIDE B
A

CLAMP

C
1 2 3 4

29

DEH-1450,1450B

5. ELECTRICAL PARTS LIST


NOTES: - Parts whose parts numbers are omitted are subject to being not supplied. - The part numbers shown below indicate chip components. Chip Resistor RS1/_S___J,RS1/__S___J Chip Capacitor (except for CQS.....) CKS....., CCS....., CSZS.....
=====Circuit Symbol and No.===Part Name --- ----------------------------------------------Part No. ------------------------=====Circuit Symbol and No.===Part Name --- ----------------------------------------------Part No. -------------------------

A
IC IC IC IC IC Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q D D D D D D D D D D D D D D D D L L L L L L L L X AR

Unit Number : CWM7944 Unit Name : Tuner Amp Unit


301 361 603 610 901 351 359 361 410 510 511 750 751 753 909 910 911 912 913 920 921 510 750 751 753 754 759 910 911 912 913 914 919 920 921 923 924 310 361 410 411 412 617 618 750 610 410 IC IC IC IC IC Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Inductor Choke Coil 600H Ferri-Inductor Ferri-Inductor Ferri-Inductor Ferri-Inductor Ferri-Inductor Ferri-Inductor Crystal Resonator 4.194304MHz Surge Protector FM/AM Tuner Unit PML003AM TDA7386 S-80834ANY PE5262A TPD1018F IMH3A DTA124EK DTC124EK 2SC2412K 2SD2396 RN46A1 2SA1037K 2SA1036K DTC114EK RN46A1 2SD2396 2SB1243 DTC114EK 2SD1859 IMX1 DTA124EK HZS9L(B1) 1SS270 1SS270 1SS270 1SS270 MA152WA HZS9L(B3) HZS6L(B2) S5688G HZS7L(C2) HZS7L(A1) S5688G S5688G DAN202U S5688G S5688G LAU1R0K CTH1221 LAU4R7K LAU2R2K LAU2R2K LAU101K LAU2R2K LAU2R2K CSS1023 DSP-201M-S00B CWE1563

RESISTORS
R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 310 311 314 315 351 352 353 354 355 361 362 363 364 410 411 413 414 415 417 418 419 420 421 422 423 424 429 430 431 432 437 438 445 446 447 448 490 510 511 512 513 516 517 519 520 521 522 523 525 527 RS1/16S101J RS1/16S101J RS1/16S101J RS1/16S101J RD1/4PU821J RS1/16S821J RS1/16S223J RS1/16S223J RS1/16S0R0J RS1/16S103J RS1/16S103J RS1/16S331J RD1/4PU153J RS1/16S222J RS1/16S222J RS1/16S473J RS1/16S473J RS1/16S393J RS1/16S681J RS1/16S681J RS1/16S681J RS1/16S103J RS1/16S681J RD1/4PU473J RD1/4PU472J RD1/4PU473J RS1/16S681J RS1/16S681J RS1/16S473J RS1/16S473J RS1/16S0R0J RS1/16S0R0J RS1/16S272J RS1/16S272J RS1/16S162J RS1/16S162J RS1/16S0R0J RD1/4PU221J RD1/4PU221J RD1/4PU472J RD1/4PU222J RS1/16S104J RD1/4PU222J RD1/4PU102J RS1/16S0R0J RS1/16S0R0J RS1/16S0R0J RS1/16S0R0J RS1/16S0R0J RS1/16S0R0J

MISCELLANEOUS

30

DEH-1450,1450B

=====Circuit Symbol and No.===Part Name --- ----------------------------------------------R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 531 532 536 537 538 612 613 614 615 616 617 618 622 623 625 712 750 751 752 753 754 755 758 759 764 765 767 769 774 775 777 778 779 791 910 911 912 913 914 915 916 917 918 919 920 921 922 923 924 927 928 929 930 931 937 939

Part No. ------------------------RD1/4PU222J RD1/4PU222J RD1/4PU102J RS1/16S104J RS1/16S0R0J RS1/16S0R0J RD1/4PU102J RS1/16S821J RS1/16S473J RS1/16S682J RS1/16S473J RS1/16S223J RD1/4PU104J RD1/4PU104J RS1/16S0R0J RD1/4PU104J RD1/4PU104J RS1/16S103J RS1/16S153J RS1/16S153J RS1/16S222J RD1/4PU222J RS1/16S102J RS1/16S222J RS1/16S0R0J RS1/16S1R0J RS1/16S103J RS1/16S102J RS1/16S0R0J RS1/16S1R0J RS1/16S152J RS1/16S152J RD1/4PU103J RS1/16S0R0J RS1/16S1R0J RD1/4PU220J RD1/4PU132J RD1/4PU122J RS1/16S103J RS1/16S222J RD1/4PU153J RS1/16S104J RS1/16S104J RS1/16S104J RS1/16S473J RS1/16S103J RS1/16S473J RD1/4PU102J RS1/16S472J RS1/16S102J RS1/16S473J RS1/16S0R0J RS1/16S0R0J RS1/16S0R0J RS1/16S152J RS1/16S0R0J

=====Circuit Symbol and No.===Part Name --- ----------------------------------------------C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C 321 324 326 327 329 351 352 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 410 412 413 414 415 417 418 419 424 425 510 511 512 515 516 614 615 616 617 618 619 620 621 751 910 911 912 913 914 915 916 918 919 330F/16V

Part No. ------------------------CKSRYB153K25 CCSRCH100D50 CCSRCH100D50 CCSRCH100D50 CCSRCH100D50 CEJQ2R2M50 CEJQ2R2M50 CCH1368 CKSRYB104K25 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CEJQ330M10 CEJQ2R2M50 CKSQYB225K10 CKSQYB225K10 CEJQ100M16 CKSQYB103K25 CKSRYB223K50 CKSRYB102K50 CEJQ220M10 CKSRYB223K50 CKSRYB472K50 CEJQ101M6R3 CKSRYB473K50 CKSRYB183K25 CKSRYB183K25 CKSRYB473K50 CKSRYB102K50 CEJQ101M10 CKSRYB102K50 CKSRYB102K50 CKSRYB473K50 CEJQ2R2M50 CKSRYB104K25 CCSRCH101J50 CEJQ4R7M35 CKSRYB473K50 CCSRCH150J50 CCSRCH150J50 CKSRYB104K25 CCH1326 CKSRYB103K50 CEJQ101M16 CEJQ101M10 CKSRYB473K50 CKSRYB103K50 CCH1331 CKSQYB473K50 CKSRYB103K50

3300F/16V

470F/16V

CAPACITORS
C C C C C C C C C C 307 308 309 310 311 312 313 314 315 316 CEJQ470M10 CEJQ100M16 CKSRYB104K25 CKSRYB105K6R3 CKSRYB104K25 CKSRYB104K25 CKSRYB105K6R3 CEJQ4R7M35 CEJQ4R7M35 CKSRYB153K25

B
IC D D D D

Unit Number : CWM7957(DEH-1450/XM/ES) Unit Name : Keyboard Unit


IC LED LED LED LED PD6340A NSSW440-9159 NSSW440-9159 SML-310PT SML-310PT

MISCELLANEOUS
1800 1700 1701 1702 1703

31

DEH-1450,1450B

=====Circuit Symbol and No.===Part Name --- ----------------------------------------------D D D D D D D X IL IL 1704 1705 1706 1707 1708 1800 1801 1800 1700 1701 LED LED LED LED LED Diode Diode Ceramic Resonator 4.97MHz Lamp 14V 40mA Lamp 14V 40mA LCD

Part No. ------------------------SML-310PT SML-310PT SML-310PT SML-310PT SML-310PT MA152WK MA152WA CSS1573 CEL1651 CEL1651 CAW1723

=====Circuit Symbol and No.===Part Name --- ----------------------------------------------R R R R R R R R R R R R R R R R R 1709 1710 1711 1712 1713 1714 1715 1716 1717 1718 1719 1800 1801 1802 1803 1804 1805

Part No. ------------------------RS1/16S151J RS1/16S151J RS1/16S121J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S222J RS1/16S222J RS1/16S471J RS1/16S471J RS1/16S471J RS1/16S471J

RESISTORS
R R R R R R R R R R R R R R R R R R R R R R 1700 1701 1702 1703 1708 1709 1710 1711 1712 1713 1714 1715 1716 1717 1718 1719 1800 1801 1802 1803 1804 1805 RS1/16S101J RS1/16S101J RS1/16S101J RS1/16S101J RS1/16S151J RS1/16S151J RS1/16S151J RS1/16S820J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S121J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S121J RS1/16S222J RS1/16S222J RS1/16S471J RS1/16S471J RS1/16S471J RS1/16S471J

CAPACITORS
C C C 1700 1701 1800 CKSQYF104Z50 CKSQYF104Z50 CKSRYB103K50

C
IC IC IC IC Q Q L L X S S S S S

Unit Number : CWX2481 Unit Name : Control Unit

MISCELLANEOUS
101 201 401 701 101 102 201 202 301 901 902 903 904 905 IC IC IC IC Transistor Transistor Inductor Inductor Ceramic Resonator 16.934MHz Spring Switch(HOME) Spring Switch(CLAMP) Spring Switch(DSCSNS) Spring Switch(12EJ) Spring Switch(8EJ) TA2153FN TC9495F2 BA5996FM BA05SFP 2SD1664 UMD2N CTF1546 CTF1546 CSS1525 CSN1051 CSN1052 CSN1051 CSN1052 CSN1051

CAPACITORS
C C C 1700 1701 1800 CKSQYF104Z50 CKSQYF104Z50 CKSRYB103K50

B
IC D D D D D D D D D D D X IL IL

Unit Number : CWM7958(DEH-1450B/XM/ES) Unit Name : Keyboard Unit


IC LED LED LED LED LED LED LED LED LED Diode Diode Ceramic Resonator 4.97MHz Lamp 14V 40mA Lamp 14V 40mA LCD PD6340A NSSW440-9159 NSSW440-9159 SML-310VT SML-310VT SML-310VT SML-310VT SML-310VT SML-310VT SML-310VT MA152WK MA152WA CSS1573 CEL1662 CEL1662 CAW1688

RESISTORS
R R R R R R R R R R R R R R R R R R R R R R R R R 101 102 103 201 202 203 204 206 208 209 210 211 212 213 215 216 301 302 303 304 306 307 312 313 315 RS1/16S222J RS1/8S120J RS1/8S100J RS1/16S513J RS1/16S513J RS1/16S823J RS1/16S823J RS1/16S823J RS1/16S124J RS1/16S183J RS1/16S153J RS1/16S103J RS1/16S103J RS1/16S124J RS1/16S0R0J RS1/16S471J RS1/16S333J RS1/16S332J RS1/16S332J RS1/16S514J RS1/16S102J RS1/16S102J RS1/16S103J RS1/16S473J RS1/16S334J

MISCELLANEOUS
1800 1700 1701 1702 1703 1704 1705 1706 1707 1708 1800 1801 1800 1700 1701

RESISTORS
R R R R R 1700 1701 1702 1703 1708 RS1/16S101J RS1/16S101J RS1/16S101J RS1/16S101J RS1/16S151J

32

DEH-1450,1450B

=====Circuit Symbol and No.===Part Name --- ----------------------------------------------R R R R R R R R R R R R R R R R R R R R R R R R R 321 322 323 401 402 403 404 405 407 408 409 410 701 702 703 704 705 706 707 708 709 710 901 902 903

Part No. ------------------------RS1/16S331J RS1/16S0R0J RS1/16S332J RS1/16S684J RS1/16S103J RS1/16S103J RS1/16S183J RS1/16S123J RS1/16S622J RS1/16S622J RS1/16S113J RS1/16S752J RS1/16S102J RS1/16S221J RS1/16S221J RS1/16S221J RS1/16S221J RS1/16S221J RS1/16S221J RS1/16S102J RS1/16S102J RS1/16S102J RS1/16S104J RS1/16S473J RS1/16S273J

=====Circuit Symbol and No.===Part Name --- ----------------------------------------------C C C C C C C C C 402 403 404 405 702 703 801 802 803 10F/10V

Part No. ------------------------CKSRYB221K50 CKSRYB153K25 CKSRYB103K50 CEV101M10 CKSRYB104K16 CKSRYB104K16 CCH1349 CEV101M10 CKSRYB224K16

Miscellaneous Parts List


M M 1 2 Pickup Unit(Service)(P9) Motor Unit(SPINDLE) Motor Unit(LOADING/CARRIAGE) CXX1480 CXB6007 CXB5903

CAPACITORS
C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C 101 102 103 104 105 106 107 201 202 204 205 206 207 208 209 210 211 301 302 303 304 305 306 307 308 309 310 311 312 315 317 318 319 320 325 328 329 330 331 401 CEV470M6R3 CKSRYB102K50 CKSRYB104K16 CKSRYB224K16 CEV470M6R3 CKSRYB104K16 CKSRYB105K6R3 CKSRYB104K16 CCSRCH560J50 CKSRYB224K16 CKSRYB224K16 CKSRYB273K25 CKSRYB273K25 CKSRYB104K16 CKSRYB104K16 CCSRCK2R0C50 CCSRCH220J50 CKSRYB153K25 CKSRYB104K16 CKSRYB103K50 CKSRYB103K50 CKSRYB104K16 CKSRYB104K16 CKSRYB333K16 CKSRYB104K16 CKSRYB473K16 CKSRYB473K16 CKSRYB104K16 CKSRYB104K16 CEV220M6R3 CKSRYB104K16 CKSRYB104K16 CKSRYB104K16 CCSRCH470J50 CKSRYB471K50 CKSRYB472K50 CKSRYB104K16 CKSRYB104K16 CKSRYB104K16 CKSRYB221K50

33

DEH-1450,1450B

6. ADJUSTMENT
6.1 CD ADJUSTMENT
1) Precautions This unit uses a single power supply (+5V) for the regulator. The signal reference potential, therefore, is connected to VREF(approx. 2.1V) instead of GND. If VREF and GND are connected to each other by mistake during adjustments, not only will it be impossible to measure the potential correctly, but the servo will malfunction and a severe shock will be applied to the pick-up. To avoid this, take special note of the following. Do not connect the negative probe of the measuring equipment to VREF and GND together. It is especially important not to connect the channel 1 negative probe of the oscilloscope to VREF with the channel 2 negative probe connected to GND. Since the frame of the measuring instrument is usually at the same potential as the negative probe, change the frame of the measuring instrument to floating status. If by accident VREF comes in contact with GND, immediately switch the regulator or power OFF. Always make sure the regulator is OFF when connecting and disconnecting the various filters and wiring required for measurements. Before proceeding to further adjustments and measurements after switching regulator ON, let the player run for about one minute to allow the circuits to stabilize. Since the protective systems in the unit's software are rendered inoperative in test mode, be very careful to avoid mechanical and /or electrical shocks to the system when making adjustment. The RFI and RFO signals are easy to oscillate because of a wide band. When observing them, insert a resistor of about 1 k to the series. This equipment will not guarantee the load ejection operation when the mechanical unit is turned upside down. In particular, if the ejection operation is incorrectly performed and recovery is disabled, the recovery is enabled by resetting a product or turning ACC off to on. 2) Test Mode This mode is used for adjusting the CD mechanism module of the device. Test mode starting procedure Reset while pressing the 4 and 6 keys together. Test mode cancellation Switch ACC, back-up OFF. After pressing the EJECT key, do not press any other key until the disk is completely ejected. If the ] or [ key is pressed while focus search is in progress, immediately turn the power off (otherwise the actuator may be damaged due to adhesion of the lenses).

34

DEH-1450,1450B

6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT


Note : The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the PU unit must be changed, the grating should be checked using the procedure below.

Purpose : To check that the grating is within an acceptable range when the PU unit is changed. Symptoms of Mal-adjustment : If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform track search operations, or taking a long time for track searching. Method : Measuring Equipment Measuring Points Disc Mode

Oscilloscope, Two L.P.F. E, F, VREF ABEX TCD-784 TEST MODE

CONTROL UNIT

L.P.F. E VREF Xch 100k 390pF Ych

Oscilloscope

F VREF
VREF

100k 390pF L.P.F.

Checking Procedure 1. In test mode, load the disc and switch the 5V regulator on. 2. The display will change, returning to "81" on the fourth press. 3. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase difference is within 75 . Refer to the photographs supplied to determine the phase angle. 4. If the phase difference is determined to be greater than 75 try changing the PU unit to see if there is any improvement. If, after trying this a number of times, the grating angle does not become less than 75 then the mechanism should be judged to be at fault. Note Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle. Hint Reloading the disc changes the clamp position and may decrease the "wobble".

E F

35

DEH-1450,1450B

Grating waveform

Ech Xch 20mV/div, AC Fch Ych 20mV/div, AC 30

45

60

75

90

36

DEH-1450,1450B

6.3 ERROR MODE


- Error Messages
If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of the error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from the users and also for facilitating trouble analysis and repair work in servicing. (1) Basic Indication Method 1) When SERRORM is selected for the CSMOD (CD mode area for the system), error codes are written to DMIN (minutes display area) and DSEC (seconds display area). The same data is written to DMIN and DSEC. DTNO remains in blank as before. 2) Head unit display examples Depending on display capability of LCD used, display will vary as shown below. xx contains the error number. 8-digit display ERRORxx 6-digit display ERRxx 4-digit display Exx

(2) Error Code List Code Class Displayed error code Description of the code and potential cause(s) 10 Electricity Carriage Home NG CRG can't be moved to inner diameter. SERVO LSI ComCRG can't be moved from inner diameter. munication Error Failure on home switch or CRG move mechanism. 11 12 Electricity Electricity Focus Servo NG Spindle Lock NG Subcode NG Communication error between microcomputer and SERVO LSI. Focusing not available. Stains on rear side of disc or excessive vibrations on REWRITABLE. Spindle not locked. Sub-code is strange (not readable). Failure on spindle, stains or damages on disc, or excessive vibrations. A disc not containing CD-R data is found. Turned over disc are found, though rarely. CD signal error. AGC protection doesn't work. Focus can be easily lost. Damages or stains on disc, or excessive vibrations on REWRITABLE. Failed to reach target address. CRG tracking error or damages on disc. Skip setting for all track. (CD-R/RW) Mechanical error during CD ON. Defective loading motor, mechanical lock and mechanical sensor. A0 System Power Supply NG Power (VD) is ground faulted. Failure on SW transistor or power supply (failure on connector).

17 30 44 50

Electricity Electricity Electricity

Setup NG Search Time Out ALL Skip

Mechanism CD On Mech Error

Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors). Unreadable TOC does not constitute an error. An intended operation continues in this case. Upper digits of an error code are subdivided as shown below: 1x: Setup relevant errors, 3x: Search relevant errors, Ax: Other errors.

37

DEH-1450,1450B

7. GENERAL INFORMATION
7.1 DIAGNOSIS 7.1.1 DISASSEMBLY
- Removing the Case (not shown) 1. Remove the Case.

CD Mechanism Module
- Panel Assy (Fig.1) Take the two stoppers off the Chassis and then remove the Panel Assy.

- Removing the CD Mechanism Module (Fig.1) Remove the four screws and then remove the CD Mechanism Module.

Panel Assy

Fig.1

- Removing the Tuner Amp Unit (Fig.2) Remove the two screws.

Straight the tabs at three locations indicated.

Remove the three screws.

Remove the screw and then remove the Tuner Amp Unit.

Fig.2

Tuner Amp Unit

38

DEH-1450,1450B

- How to hold the Mechanical Unit


1. Hold the top and bottom frame. 2. Do not squeeze top frame's front portion too tight, because it is fragile.

Do not squeeze.

- How to remove the Top and Bottom Frame


1. When the disk is in "clamp" state, unlock Spring A (6 pieces) and Spring B (2 pieces), and unscrew screws (4 pieces). 2. Unlock each 1 of pawl at the both side of the frame, then remove the top frame. 3. Remove the Carriage Mechanical part in such way Carriage Mechanical that; you remove the mechanical part from 3 pieces Part of Damper while slowly pulling up the part. 4. Now, the top frame has been removed, and under this state, fix the genuine Connector again, and eject the disk. (Caution) Bottom Frame When you reassemble the Carriage Mechanical part, apply a bit of alcohol to Dampers. Top Frame

Damper

- How to remove the Guide Arm Assy


1. Unlock the spring (1 piece) at the right side of the assembly. 2. Unscrew screws (2 pieces), then remove the Screw Gear Bracket. 3. Shift the Guide Arm Assy to the left and slowly rotate it to the upper direction. 4. When the Guide Arm Assy rotates approximately 45 degree, shift the Assy to the right side direction and remove it.

Screw Gear Bracket Guide Arm Assy

Spring

39

DEH-1450,1450B

- How to remove the Control Unit


1. Give jumper-solder treatment to the Flexible Wire of the Pickup unit, then remove the wire from the Connector. 2. Remove all 4 points of solder-treatment on the Lead Wire. Also, unscrew the screw(1 piece). 3. Then, Remove the Control unit. (Caution) Be careful not to damage SW when you reassemble the Control Unit into the device. Jumper-Solder Control Unit

Solder

- How to remove the Loading Arm Assy


1. Unlock the spring (1 piece) and remove the E ring (1 piece) of the Fulcrum Shaft. 2. Shift the arm to the left side direction and unlock pins (2 pieces).

Loading Arm Assy

- How to remove the Pickup Unit


1. Unscrew 2 pieces of screws, then remove the Pulley Cover. 2. Remove the Feed Screw unit from the pawl of the Feed Screw Guide (The pawl is located inside the guide). 3. Remove the belt from the Pulley, then remove the Pickup unit. Pulley Cover (Caution) Make sure not to stain the belt with grease when you fix the belt. Grease Application Pickup Unit Grease Application Belt

Feed Screw Guide Grease Application

40

DEH-1450,1450B

7.1.2 CONNECTOR FUNCTION DESCRIPTION

ANTENNA PRE OUT


16 14 12 10 8 6 4 2 15 13 11 9 7 5 3 1

1. GND 2. BACK UP 3. ACC 4. NC 5. NC 6. B.REM 7. NC 8. NC 9. RL10. FL11. RL+ 12. FL+ 13. RR14. FR15. RR+ 16. FR+

41

DEH-1450,1450B

7.2 PARTS 7.2.1 IC


- Pin Functions(PE5262A) Pin No. Pin Name 1 MODEL1 2,3 NC 4 AVSS 5 ST 6 SD 7 AVREF1 8 KYDT 9 DPDT 10 SDBW 11 TUNPDI 12 TUNPDO 13 TUNPCK 14 TUNPCE 15 currq 16 LOCL 17 NC 18 fm/AM 19 NC 20 FLPILM 21 VDCONT 22 NC 23 CONT 24 XCE 25 xrst 26 XPCK 27-30 XPI0-3 31 CLCONT 32 HOME 33 VSS 34 LOEJ 35 CD5VON 36,37 ROT1-0 38 TELIN 39 NC 40 ILMPW 41 swvdd 42 SYSPW 43 VST 44 mute 45 PEE 46 LOCH 47 NC 48 TUNPCE2 49 PCL 50 VCK 51 VDT 52 ANTPW 53 EJECTS 54 DALMON 5559 NC 60 reset 61,62 NC 63 bsens 64 asens 65 dsens 66 ADPW 67 NC I/O I I I I I O I I O O O O O O O O O O O O I/O O I O O I I O O O O O O O O O O O O I O I I I I O Format Function and Operation Model select input Not used A/D GND FM stereo input SD input A/D converter reference voltage Key data input Display data output SDBW input PLL IC data input PLL IC data output PLL IC clock output PLL IC chip enable output Tuner voltage FIX output Local L output Not used FM/AM power select output Not used Inside of flap illumination output VD control output Not used Servo driver power supply control output CD LSI chip enable output CD LSI reset output CD LSI clock output CD LSI data input/output Driver input select output Home position detector input GND CD load motor LOAD/EJECT direction exchange output CD +5V power supply control output Rotary encoder data input Telephone mute input Not used Illumination power supply control output Keyboard unit power supply control output System power supply control output Strobe pulse output for electronic volume System mute output Beep tone output Local H output Not used EEPROM chip enable output Clock adjustment output Clock output for electronic volume Data output for electronic volume Antenna output Eject key input pin Stand-by output Not used Reset input Not used Back up power sense input ACC power sense input Grille detach sense A/D converter power supply output Not used

C C C C C C C C C C C C C C C C

C C C C C C C C C C C

42

DEH-1450,1450B

Pin No. 68 69 70 71 72 73 74 75 76 77 78 79 80

Pin Name VDD X2 X1 IC(VPP) NC TESTIN AVDD AVREF0 SL TEMP VDSENS DISCSNS CSENS

I/O

Format

I I I I I

Function and Operation Power supply Crystal oscillator connection pin Crystal oscillator connection pin Connect to GND Not used Test program mode input Positive power supply terminal for analog circuit A/D converter reference voltage SD level input from tuner CD temperature sense input VD power supply voltage sense input CD DISC sense input Flap open/close sense input

Output Format C N *PE5262A 80 1

Meaning C MOS output N channel open drain output

IC's marked by * are MOS type. Be careful in handling them because they are very liable to be damaged by electrostatic induction.

61 60

20 21 40

41

43

DEH-1450,1450B

- Pin Functions (PD6340A)


Pin No. 1-5 6-9 10 11-14 15,16 17 18 19 20 21 22 23 24 25,26 27 28 29-32 33-55 56 57-64 Pin Name SEG4-0 COM3-0 VLCD KST3-0 KDT0,1 REM DPDT NC KYDT MODA X0 X1 VSS KDT2,3 NC KST4 NC SEG35-13 VDD SEG12-5 I/O O O O I I I O Function and Operation LCD segment output LCD common output LCD drive power supply Key strobe output Key data input (analogue input) Remote control reception Display data input Not used Key data output GND Crystal oscillator connection pin Crystal oscillator connection pin GND Key data input Not used Key strobe output Not used LCD segment output Power supply LCD segment output

I O O O

*PD6340A

33

32

48 49 64 1

17 16
44

DEH-1450,1450B

- Pin Functions(TA2153FN)
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Pin Name VCC RFGC GMAD FNI FPI TPI TNI MDI LDO SEL TEB 2VRO TEN TEO SBAD FEO FEN SEB VRO RFRP BTC RFCT PKC RFRPIN RFGO GVSW AGCIN RFO GND RFN2 I/O I I I I I I O I I I O I O O O I I O O I O I I O I I O I I Function and Operation Power supply voltage terminal RF amplitude adjustment control signal terminal AGC amplifier frequency characteristic adjustment terminal Main beam amplifier input terminal Main beam amplifier input terminal Sub beam amplifier input terminal Sub beam amplifier input terminal Monitor photodiode amplifier input terminal Laser diode amplifier output terminal APC circuit ON/OFF signal, LDO terminal control input terminal and bottom and peak detection frequency switching terminals Tracking error balance adjustment signal input terminal Reference voltage (2VRO) output terminal Tracking error signal generation amplifier reverse phase input terminal Tracking error signal generation amplifier output terminal Sub beam addition signal output terminal Focus error signal generation amplifier output terminal Focus error signal generation amplifier reverse phase input terminal RFRP generation circuit mode switching terminal Reference voltage (VREF) output terminal Signal generation amplifier output terminal for track count Bottom detection time constant adjustment terminal for RFCT signal generation RFRP signal center level output terminal Peak detection time constant adjustment signal for RFCT signal generation Signal generation amplifier input terminal for track count RF signal amplitude adjustment amplifier output terminal AGC, FE or TE amplifier gain switching terminal RF signal amplitude adjustment amplifier input terminal RF signal generation amplifier output terminal GND terminal RF signal generation amplifier input terminal

TA2153FN

15

16

30

45

DEH-1450,1450B

- Pin Functions(TC9495F2)
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 Pin Name TESTO hso uhso EMPH LRCK VSS BCK AOUT DOUT MBOV IPF SBOK CLCK VDD VSS DATA SFSY SBSY SPCK SPDA COFS MONIT VDD TESIO0 P2VREF HSSW ZDET PDO TMAXS TAMX LPFN LPFO PVREF VCOREF VCOF AVSS SLCO RFI AVDD RFCT RFZI RFRP FEI SBAD TSIN TEI TEZI FOO TRO VREF RFGC TEBC FMO FVO DMO 2VREF SEL I/O O O O O O O O O O O I/O Function and Operation Test mode terminal Replay speed flag output terminal Replay speed flag output terminal Emphasis flag output terminal for sub code Q data Channel clock (44.1 kHz) output terminal Digital ground terminal Bit clock output terminal Digital audio data output terminal Digital out output terminal Buffer memory over signal output terminal Correction flag output terminal CRCC decision result output for sub code Q data Clock input/output terminal for sub code P-W data read Digital + power supply terminal (5 V) Digital ground terminal Sub code P-W data output terminal Replay-system frame sync signal output terminal Sub code block sync output terminal Clock for processor status signal read Processor status signal output terminal Correction-system frame clock (7.35 kHz) output terminal LSI internal signal output terminal Digital + power supply terminal (5 V) Test input/output terminal PLL-system only 2VREF terminal The VREF voltage is reached for double or quad speed. One-bit DAC zero detection flag output terminal Phase error signal issue between the EFM and PLCK signals TMAX detection result output terminal TMAX detection result output terminal Reverse input terminal of amplifier for lowpass filter Output terminal of amplifier for lowpass filter PLL-system only VREF terminal VCO center frequency reference level terminal Filter terminal for VCO Analog-system ground terminal Output terminal of DAC for data slice level generation RF signal input terminal Analog-system power supply terminal (5 V) RFRP signal center level input terminal Input terminal for RFRP signal zero cross RF ripple signal input terminal Focus error signal input terminal Sub beam addition signal input terminal Test input terminal Tracking error input terminal Input terminal for tracking error or zero cross Focus equalizer output terminal Tracking equalizer output terminal Analog reference power supply terminal RF amplitude adjustment control signal output terminal Tracking balance control signal output terminal Feed equalizer output terminal Speed error signal or feed search EQ output Disc equalizer output terminal Analog reference power supply terminal APC circuit ON/OFF signal output terminal

O O O O O O O I O O O O O I O I O O I I I I I I I I I O O O O O O O O

46

DEH-1450,1450B

Pin No. 58-61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87-89 90-93 94 95 96 97 98 99 100

Pin Name FLGA-D VDD VSS IO0 IO1 IO2 IO3 dmout ckse dact TESIN TESIO1 VSS PXI PXO VDD XVSS XI XO XVDD DVSR RO DVDD DVR LO DVSL TEST1-3 BUS0-3 VDD VSS BUCK cee TEST4 tsmod rst

I/O O

O O I O I I I I I I O

I O

O I I/O

I I I I I

Function and Operation External flag output terminal for internal signal monitor Digital + power supply terminal (5 V) Digital ground terminal RF amplifier gain switching terminal Not used HOME detection switch input terminal FocusDrv and signal output terminal Field equalizer PWM output terminal for IO0 and IO1 Disc equalizer PWM output terminal for IO2 and IO3 Usually open DAC test mode terminal Test input terminal Test input/output terminal Digital ground terminal DPS-system clock oscillator circuit input terminal DPS-system clock oscillator circuit output terminal Digital + power supply terminal (5 V) Ground terminal for system clock oscillator circuit System clock oscillator circuit input terminal System clock oscillator circuit output terminal For system clock oscillator circuit + power supply terminal R channel D/A converting unit power supply terminal R channel data forward rotation output terminal D/A converting unit power supply terminal (5 V) Reference voltage terminal L channel forward rotation output terminal L channel D/A converting unit power supply terminal Test mode terminal Data input/output terminal for microcomputer interface Digital + power supply terminal (5 V) Digital ground terminal Clock terminal for microcomputer interface Chip enable signal for microcomputer interface Test mode terminal Test mode terminal Reset signal input terminal

*TC9495F2 50 51 80 81 100
47

31 30 1

DEH-1450,1450B

- Pin Functions(BA5996FM)
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Pin Name VR OPIN2(+) OPIN2(-) OPOUT2 OPIN1(+) OPIN1(-) OPOUT1 GND MUTE POWVCC1 VO1(-) VO1(+) VO2(-) VO2(+) VO3(+) VO3(-) VO4(+) VO4(-) POWVCC2 GND CNT LDIN OPOUTSL OPINSL OPOUT3 OPIN3(-) OPIN3(+) PREVCC Function and Operation Input pin for reference voltage Input pin for non-inverting input for CH2 preamplifier Input pin for inverting input for CH2 preamplifier Output pin for CH2 preamplifier Input pin for non-inverting input for CH1 preamplifier Input pin for inverting input from CH1 preamplifier Output pin for CH1 preamplifier Ground pin Mute control pin Power supply pin for CH1, CH2, and CH3 at "Power" stage Driver CH1 - Negative output Driver CH2 - Positive output Driver CH2 - Negative output Driver CH2 - Positive output Driver CH2 - Positive output Driver CH2 - Negative output Driver CH4 - Positive output Driver CH4 - Negative output Power supply pin for CH4 at "Power" stage Ground pin Control pin Loading input Output pin for preamplifier for thread Input pin for preamplifier for thread CH3 preamplifier output pin Input pin for inverting input for CH3 preamplifier Input pin for non-inverting input for CH3 preamplifier PreVcc

BA5996FM

14

15

28

48

DEH-1450,1450B

- FM/AM Tuner Unit


AMRF
28 AMANT

FM/AM 1ST IF 10.7MHz T51 Q51 CF51 CF52 CF53

MPXREF 41kHz AMDET IC 2 FM MPX


L ch 6 R ch 5

ATT

ANT ADJ
FMANT

IC1 MIXER, IF AMP, DET.

COMP LDET

21 18

27 RFGND 26

ATT FMRF CF202 IMG ADJ AM 2ND IF X901 450kHz 10.25MHz


WC NC NC

IC 3 EEPROM
FMLOCL SDBW DGND FMSD DI/DO NL1 NL2 4 CE2 CE1 STIND 1

NC

CK

LOCH 23 25

LOCL

7 17 20 22 10 19 14

24

11 12 15 16

SL 13

RF ADJ

CREQ

VDD VCC

No. Symbol I/O Explain 1 STIND O stereo indicator 2 FMSD O FM station detector

"Low" when the FM stereo signals are received. To be pulled up to the "VDD" at 47k. "High" when signals are received. To be pulled up to the "VDD" at 47k Meanwhile, 10k should be used when taking diver FIX trigger from here and "High: 0.9VDD or more" and "Low: 250mV or less". (Should satisfy the diver IC specifications) 3 NL1 O noise level-1 "High" when noise is received. Output for the RDS. GND at 47k //1,800pF. 4 NL2 O noise level-2 "High" when noise is received. Output for the RDS. GND at 36k //330pF. 5 Rch O R channel FM stereo "R-ch" signal output or AM audio output. output Add the specified de-emphasis constant. 6 Lch O L channel FM stereo "L-ch" signal output or AM audio output. output Add the specified de-emphasis constant. 7 WC write control EEPROM write control. Writing permissible at "Low". Normally open. 8 SDBW O SD bandwidth SD bandwidth signal output. For detection of detuning data for the RDS. 9 NC Not used 10 VDD power Power supply pin for the digital section. supply DC 5V +/- 0.25V. Be careful about overlapping noise in the logic section. 11 DGND digital ground Grounding for the digital section. 12 CE2 I chip enable-2 EEPROM chip enable. Active a "Low" To be pulled up to the "VDD" at 47k 13 SL I/O signal level Received FM/AM signal level (strength) output. Connect the specified load resistor and capacitor (10k + 39k //4,700pF) 14 DI/DO I/O data input/ Data input/Data output data output To be pulled up to the "VDD" at 47k 15 CK I clock Clock input To be pulled up to the "VDD" at 47k 16 CE1 I chip enable-1 AFRF chip enable. Active at "High" To be grounded at 47k 17 NC Not used 18 LDET O lock detector Active at "Low". To be pulled up to the "VDD" at 47k 19 CREQ I current request Active at "Low". To be grounded at 47k 20 NC Not used 21 COMP O composite signal FM composite signal output. r out < 100 22 VCC power supply Analog section power supply pin.DC 8.4V +/- 0.3V 23 LOCH I local high FM local high pin. When seeking local high, apply 5V together with "LOCL". 24 FMLOCL I FM local low FM local low pin. When seeking local low, apply 5V to the base of the NPN transistor with which the specified resistor is being connected to the emitter. Keep it open in case of ordinary marketed models. 25 LOCL I local low FM/AM local low pin. When seeking local low, apply 5V to the base of the NPN transistor. Since this pin is exclusive for AM when the FMLOCL is in use, do not drive it under FM. 26 RFGND RF ground Grounding for the antenna section. 27 FMANT I FM antenna input FM antenna input. 75. Surge absorber (DSP-201M-S00B) is necessary. 28 AMANT I AM antenna input AM antenna input. High impedance. Connect to the antenna through an L (LAU type) of 4.7H.To cope with the power transmission line hums, insert a series circuit consisting of an L (a coil of about 100mH) + R (a resistor of 470 to 2.2k) between the GND.
49

COM3A COM2A COM1A COM2B COM0A COM2C COM3B COM2D COM1B COM0B

COM3A COM2A COM1A COM2B COM0A COM2C COM3B COM2D COM1B COM0B SEG39 SEG38 SEG37 SEG35 SEG34 SEG33 SEG32 SEG31 SEG30 SEG29 SEG28 SEG27 SEG26 SEG25 SEG24 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 NC NC SEG36

50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

DEH-1450,1450B

50

- CAW1723(DEH-1450/XM/ES), CAW1688(DEH-1450B/XM/ES)

7.2.2 DISPLAY

COMMON

SEGMENT

DEH-1450,1450B

7.3 OPERATIONAL FLOW CHART


Power ON

VDD=5V Pin 68

bsens Pin 63 BSENS=L asens Pin 64 ASENS=L dsens Pin 65 DSENS=L ADPWH Pin 66

Starts communication with Grille microcomputer. 300ms swvddL Pin 41 Source keys operative

300ms In case of the above signal, the communication with Grille microcomputer may fail. If the time interval is not 300msec, the oscillator may be defective.

Source ON

SYSPWH Pin 42

Completes power-on operation.(After that, proceed to each source operation.)

51

DEH-1450,1450B

8. OPERATIONS AND SPECIFICATIONS


8.1 OPERATIONS

4 6 5 7

Whats what
1 VOLUME button Press to increase or decrease the volume. 2 CD EJECT button Press to eject a CD from your built-in CD player. 3 AUDIO button Press to select various sound quality controls. 4 CLOCK button Press to switch clock display on or off. 5 EQ button Press to select various equalizer curves. 6 5//2/3 buttons Press to do manual seek tuning, fast forward, reverse and track search controls. Also used for controlling functions. 7 LOUDNESS button Press to switch loudness function on or off. 8 SOURCE button This unit is switched on by selecting a source. Press to cycle through all of the available sources. 9 16 (PRESET TUNING) buttons Press for preset tuning. 0 LOCAL/BSM button ! BAND button Press to select among three FM and one AM band. @ DETACH button Press to remove the front panel from the head unit.

52

Power ON/OFF
Listening to the radio
2 Use VOLUME to adjust the sound level. When you press VOLUME up/+, the volume is raised and when pressed down/, the volume is lowered. 1 Press SOURCE to select the tuner.

Tuner
Playing a CD

Built-in CD player

Turning the unit on

Press SOURCE to turn the unit on. When you select a source the unit is turned on.

1 2
3 Press BAND to select a band. Press BAND until the desired band is displayed, FM1, FM2, FM3 for FM or AM.

3 4 1

Selecting a source
1 BAND indicator Shows which band the radio is tuned to, AM or FM. 4 To perform manual tuning, press 2 or 3 with quick presses. The frequencies move up or down step by step.

If you are using this unit in North, Central or South America, reset the AM tuning step .

You can select a source you want to listen to. To switch to the built-in CD player, load a disc in this unit.

1 TRACK NUMBER indicator Shows the track currently playing. 2 PLAY TIME indicator Shows the elapsed playing time of the current track. 1 Insert a CD into the CD loading slot. Playback will automatically start. CD loading slot

Press SOURCE to select a source. Press SOURCE repeatedly to switch between the following sources: Built-in CD playerTuner 2 FREQUENCY indicator Shows to which frequency the tuner is tuned. 3 STEREO () indicator Shows that the frequency selected is being broadcast in stereo. 4 PRESET NUMBER indicator Shows what preset has been selected.

Notes

5 To perform seek tuning, press and hold 2 or 3 for about one second and release. The tuner will scan the frequencies until a broadcast strong enough for good reception is found. You can cancel seek tuning by pressing either 2 or 3 with a quick press. If you press and hold 2 or 3 you can skip broadcasting stations. Seek tuning starts as soon as you release the buttons. Note When the frequency selected is being broadcast in stereo the STEREO () indicator will light.

When no disc is set in this product, built-in CD player source will not change. When this units blue/white lead is connected to the cars auto-antenna relay control terminal, the cars antenna extends when this units source is switched on. To retract the antenna, switch the source off.

You can eject a CD by pressing CD EJECT. 2 After a CD has been inserted, press SOURCE to select the built-in CD player.

Turning the unit off

3 Use VOLUME to adjust the sound level. When you press VOLUME up/+, the volume is raised and when pressed down/, the volume is lowered.

Press SOURCE and hold for at least one second to turn the unit off.

DEH-1450,1450B

53

DEH-1450,1450B

54

Initial Settings
Setting the time
This is used to set the time on the units clock display. 1 Press AUDIO to select the time. Press AUDIO until the time appears in the display. 1 Press AUDIO to select FM STEP. Press AUDIO repeatedly until FM 100 appears in the display. 2 Select the FM tuning step with 2/3. Note If seek tuning is performed in 50 kHz steps, stations may be tuned in imprecisely. Tune in the stations with manual tuning or use seek tuning again. The tuning step employed by Seek Tuning in the FM mode can be switched between 100 kHz (preset at the factory) and 50 kHz.

Initial Settings
Setting the FM tuning step Setting the time display on or off
You can turn the time display on even when the sources are off.

Adjusting initial setting

Initial settings lets you perform initial set up of different settings for this unit. 2 Select the portion of the time display you wish to set with 2/3. Pressing 2/3 will select a portion of the clock display: HOURMINUTE As you select portions of the clock display the portion selected will blink.

1 Press SOURCE and hold until the unit turns off.

Press CLOCK to select the time display. Each press of CLOCK turns time display on or off. The time display disappears temporarily when you perform other operations, but the time indication is displayed again after 25 seconds.

2 Press AUDIO and hold until TIME (12:00) appears in the display. Press AUDIO repeatedly to switch between the following settings: TIMEFM STEPAM STEP Use the following instructions to operate each particular setting. To cancel initial settings, press BAND. You can also cancel initial settings by holding down AUDIO until the unit turns off. 3 Select the correct time with 5/. Pressing 5 will increase the selected hour or minute. Pressing will decrease the selected hour or minute.

Setting the AM tuning step


The AM tuning step can be switched between 9 kHz, the preset step, and 10 kHz. When using the tuner in North, Central or South America, reset the tuning step from 9 kHz (531 1,602 kHz allowable) to 10 kHz (530 1,640 kHz allowable). 1 Press AUDIO to select AM STEP. Press AUDIO repeatedly until AM 9 appears in the display. 2 Select the AM tuning step with 2/3. Pressing 2/3 will switch the AM tuning step between 9 kHz and 10 kHz. The selected AM tuning step will appear in the display.

Audio Adjustments
Using balance adjustment Using the equalizer
The equalizer lets you adjust the equalization to match car interior acoustic characteristics as desired.

Introduction of audio adjustments


Adjusting equalizer curves
You can select a fader/balance setting that provides an ideal listening environment in all occupied seats.

You can adjust the currently selected equalizer curve setting as desired. Adjusted equalizer curve settings are memorized in CSTM. 1 Press AUDIO to select the equalizer mode. Press AUDIO until EQ appears in the display. 2 Select the band you want to adjust with 2/3. L (low) M (mid) H (high)

1
There are six stored equalizer curves which you can easily recall at any time. Here is a list of the equalizer curves:
Display SBASS PWRFL NTRL VOCAL CSTM FLAT Vocal Custom Flat Natural Powerful Super bass Equalizer curve

1 Press AUDIO to select FADER. Press AUDIO until FADER appears in the display. If the balance setting has been previously adjusted, BAL will be displayed.

Recalling equalizer curves

1 AUDIO display Shows the audio adjustments status. 2 Press 5 or to adjust front/rear speaker balance. Each press of 5 or moves the front/rear speaker balance towards the front or the rear. F15 R15 is displayed as the front/rear speaker balance moves from front to rear. 0 is the proper setting when only two speakers are used.

2 LOUD indicator Appears in the display when loudness is turned on.

3 Press 5 or to adjust the equalizer curve. Each press of 5 or increases or decreases the equalizer curve respectively. +6 6 is displayed as the equalizer curve is increased or decreased. The actual range of the adjustments are different depending on which equalizer curve is selected. Note If you make adjustments when a curve other than CSTM is selected, the newly adjusted curve will replace the previous curve. Then a new curve with CSTM appears on the display while selecting the equalizer curve.

Press AUDIO to display the audio function names. Press AUDIO repeatedly to switch between the following audio functions: FADER (balance adjustment)EQ (equalizer)LOUD (loudness)FIE (front image enhancer)SLA (source level adjustment) When selecting the FM tuner as the source, you cannot switch to SLA. To return to the display of each source, press BAND. 3 Press 2 or 3 to adjust left/right speaker balance. When you press 2 or 3, BAL: 0 is displayed. Each press of 2 or 3 moves the left/right speaker balance towards the left or the right. BAL:L9 BAL:R9 is displayed as the left/right speaker balance moves from left to right.

CSTM is an adjusted equalizer curve that you create. When FLAT is selected no supplement or correction is made to the sound. This is useful to check the effect of the equalizer curves by switching alternatively between FLAT and a set equalizer curve.

Note

If you do not operate the audio function within about 30 seconds, the display is automatically returned to the source display.

Press EQ to select the equalizer. If the equalizer has been previously set to an equalizer curve other than PWRFL then the title of that previously selected equalizer curve will be displayed, such as SBASS, NTRL, VOCAL, CSTM, or FLAT.

DEH-1450,1450B

55

DEH-1450,1450B

56
5. Connecting cords with RCA pin plugs (sold separately) 7. Power amp (sold separately) 4. Fuse 6. Blue/white To system control terminal of the power amp or Auto-antenna relay control terminal (max. 300 mA 12 V DC). 8. System remote control 12. Rear speaker + + 12. Rear speaker 13. Perform these connections when using a different amp (sold separately). 17. White 14. Front speaker 15. Left 12. Rear speaker + 22. Green/black 24. Violet/black + 18. White/black 21. Green 20. Gray/black 23. Violet + 19. Gray + 16. Right 12. Rear speaker 14. Front speaker 25. With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers.

1. This Product

2. Rear output

3. Antenna jack

9. Yellow To terminal always supplied with power regardless of ignition switch position.

10. Red To electric terminal controlled by ignition switch (12 V DC) ON/OFF.

11. Black (ground) To vehicle (metal) body.

DEH-1450,1450B

8.2 SPECIFICATIONS

General
Power source .................. 14.4 V DC (10.8 15.1 V allowable) Grounding system .......... Negative type Max. current consumption ......................................... 10.0 A Backup current ................ 3 mA Dimensions (W H D): (DIN) Chassis .............. 178 50 157 mm Nose .................. 188 58 19 mm (D) Chassis .............. 178 50 162 mm Nose .................. 170 48 14 mm Weight ............................. 1.3 kg

CD player
System ............................ Compact disc audio system Usable discs .................... Compact disc Signal format: Sampling frequency 44.1 kHz Number of quantization bits .................................. 16; linear Frequency characteristics ......................................... 5 20,000 Hz (1 dB) Signal-to-noise ratio ....... 94 dB (1 kHz) (IEC-A network) Dynamic range ................ 92 dB (1 kHz) Number of channels ....... 2 (stereo)

FM tuner Audio
Continuous power output is 20 W per channel min. into 4 ohms, both channels driven 50 to 15,000 Hz with no more than 5% THD. Maximum power output 45 W 4 Load impedance ............. 4 (4 8 allowable) Preout max output level/output impedance ......................................... 2.2 V/1 k Equalizer (3-Band Equalizer): (LOW) ....................... Level: 12 dB (MID) ........................ Level: 12 dB (HIGH) ...................... Level: 12 dB Loudness contour (LOW) ....................... +3.5 dB (100 Hz), +3 dB (10 kHz) (MID) ........................ +10 dB (100 Hz), +6.5 dB (10 kHz) (HIGH) ...................... +11 dB (100 Hz), +11 dB (10 kHz) (volume : 30 dB) Frequency range ............. 87.5 108.0 MHz Usable sensitivity ........... 9 dBf (0.8 V/75 , mono, S/N: 30 dB) 50 dB quieting sensitivity .. 15 dBf (1.5 V/75 , mono) Signal-to-noise ratio ....... 70 dB (IEC-A network) Distortion ........................ 0.3% (at 65 dBf, 1 kHz, stereo) Frequency response ....... 30 15,000 Hz (3 dB) Stereo separation ........... 40 dB (at 65 dBf, 1 kHz)

AM tuner
Frequency range ............. 531 1,602 kHz (9 kHz) 530 1,640 kHz (10 kHz) Usable sensitivity ........... 18 V (S/N: 20 dB) Selectivity ....................... 50 dB (9 kHz) 50 dB (10 kHz)

Note Specifications and the design are subject to possible modifications without notice due to improvements.

57

Anda mungkin juga menyukai