Anda di halaman 1dari 12

NETWORK SURVEILLANCE SERVER

NSR-1000 series

PATCH FILE INSTALLATION PROCEDURE 1st Edition Revised 2

Update History
Date 2009/1/28 2009/5/25 2009/12/18 Revision 1.0 1.1 1.2 Description 1st issue 1st Edition Revised 1 1st Edition Revised 2

Patch Installation Procedure


This document describes how to install a patch file on the NSR-1000 series (hereafter referred to as NSR). There are two methods for installation, either by using the administration menu or via an FTP. The patch file is provided by Sony, and the same one can be used for both methods. During installation, the system automatically shuts down and then reboots itself. Therefore, installation work should be done during the period when you can stop operation. It takes about 10 -15 minutes to complete installation. Follow the procedures below.

1Using the Administration Menu Preparation Connect a monitor, USB keyboard and USB mouse to the NSR. Note Use a general USB keyboard and USB mouse. The ones with special keys, buttons or sticks may not work.

Save the patch file into the root directory of a USB memory device (Refer to Appendix-2) or DVD/CD. Be sure to save one patch file into the memory device. Note Confirm the NSR version in advance by clicking [Information] on the logon screen to prepare a proper patch file.(If you are already logged on to the NSR, you can display the logon screen by at the top right of the Main screen and logging off from the dialog box that appears.) clicking

If the version of the patch file is equivalent or higher than that of NSR, installation is executed. If lower, the message shown below is displayed and the patch file installation is suspended.

Procedures 1. When the system is not powered on, press the power switch on the front or rear panel of the NSR to turn it on. at the top right of the Main screen and log off from the dialog box If already logged on, click that appears. 2. The logon screen appears. Enter the user name and password of the level 5 user (=administrator) level, and click [Administration Menu].

3. Insert the USB memory into any of the three USB connectors on the front of the NSR, or insert the disc into the DVD/CD drive of the NSR. 4. Click [Patch Installation].

5. Select the media on which the patch file is stored from [Location] and select the patch file name from [Name]. Click [OK].

6. The following message appears. Click [Yes].

7. Wait for a while until the following screen appears. (This screen is kept displayed during installation.) It takes about 10 15 minutes to complete installation. Never turn off the power of NSR. Note If no screen appears after a few minutes, confirm that the patch file is highlighted in Step 5, and click [OK] again.

8. At the completion of installation, the system reboots automatically itself. Note If the version of the patch file is lower than that of NSR, the message shown below is displayed and the patch file installation is suspended.

9. Confirm that the software version is updated by clicking [Information] on the logon screen. 10. Remove the USB memory device from the USB connector, or remove the disc from the DVD/CD drive. 11. There are cases where ERROR LED on the front panel and/or ERROR lamp on the Main screen is lit. In this case, on the logon screen, enter the user name and password of the level 5 user (=administrator) level, log on to the NSR by clicking [Logon] and click ERROR lamp on the Main screen so that ERROR LED and ERROR lamp go off.

ERROR lamp on the Main screen

12. When the installation fails, the following message may appear on the screen after the system reboots. In this case, please execute DOM Restore as the message indicates.
!!!!!!!!!!!!!! ERROR !!!!!!!!!!!!!! DOM XXX partition Check error. Please press any key to start "DOM Menu" after reboot. Then, please execute "DOM Restore". !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

If you press any key on the above screen, the system will automatically reboot then appear DOM Menu as shown below. Please select the number of DOM Restore then press Enter key to execute. DOM Menu will appear again after finishing DOM Restore and please select the number of Reboot the system then press Enter key to restart the system. Please do not select other than DOM Restore and Reboot the system in the DOM Menu.

DOM Menu

2Via an FTP Preparation Prepare a PC (Windows XP or Windows Vista) and connect it to a stable IP network. Copy the patch file to any directory on the PC you desire. Note Confirm the NSR version in advance by clicking [Information] on the logon screen to prepare a proper patch file.(If you are already logged on to the NSR, you can display the logon screen by at the top right of the Main screen and logging off from the dialog box that appears.) clicking

If the version of the patch file is equivalent or higher than that of NSR, installation is executed. If lower, the message shown below is displayed and the patch file installation is suspended.

Procedures 1. When the system is not powered on, press the power switch on the front or rear panel of the NSR to turn it on. at the top right of the Main screen and log off from the dialog box If already logged on, click that appears. 2. Open Windows Explorer (not Internet Explorer) on your PC. Type the ftp address in the address bar in the form : ftp://ftpupdate@(ftp address) and press Enter key. e.g.) In case that the address of NSR is 192.168.20.32 ftp://ftpupdate@192.168.20.32
7

3The dialog box shown below is displayed. Type the password and click [Log On]. Password: up2remo!

4If the FTP session is established without fail, the destination ftp folder is displayed as shown below.

Note If the following message appears, suspect that the power of NSR is turned off.

5Drag & Drop the patch file into the destination folder to transmit it. At the completion of transmission, installation starts automatically on the NSR side. No PC operation is needed any more.

Drag & Drop the file

6. The following screen is kept displayed on the monitor of NSR during installation. It takes about 10 -15 minutes to complete installation. Never turn off the power of NSR.

Note The following message may appear as the installation proceeds. However, you can ignore it because it has no affect on the installation.

7. At the completion of installation, the system reboots automatically itself. Note If the version of the patch file is lower than that of NSR, the message shown below is displayed and the patch file installation is suspended.

8. Confirm that the software version is updated by clicking [Information] on the logon screen. Note The software version cannot be checked remotely from the PC or a similar device via the network. Check with the NSR itself.
10

Appendix-1.

Error Messages Description/Measure This patch file is unavailable for your system. Make sure again that your system needs to apply the patch. The system interrupts installation due to improper operations. Retry to install the patch file from the beginning. The system fails to copy the patch file correctly. Reboot the system first then retry to install the patch file from the beginning.

Error Message Install Patch Error Inappropriate version!! Install Patch Error Incomplete version!! The directory (/mnt/iufd/disk1pX) doesn't exist. Reboot and Install Patch again. Copy failed! (HDD #X) Copy failed! (IUFD #X)

Appendix-2.

Verified USB Memories

*With regard to USB memory devices shown below, operation check has been made on. (As of January 21, 2009) Sony USB memory device USM2GHX/W (2GB) USM2GLX (2GB) USM4GJ-B (4GB) USM8GH (8GB) USM8GL (8GB) USM16GLX (16GB)

11

( ) The material contained in this manual consists of information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation. Le matriel contenu dans ce manuel consiste en informations qui sont la proprit de Sony Corporation. Sony Corporation interdit formellement la copie de quelque partie que ce soit de ce manuel ou son employ pour tout autre but que des oprations ou entretiens de lquipement moins dune permission crite de Sony Corporation. Das in dieser Anleitung enthaltene Material besteht aus Informationen, die Eigentum der Sony Corporation sind. Die Sony Corporation untersagt ausdrcklich die Vervielfltigung jeglicher Teile dieser Anleitung oder den Gebrauch derselben fr irgendeinen anderen Zweck als die Bedienung oder Wartung der in dieser Anleitung beschriebenen Ausrstung ohne ausdrckliche schriftliche Erlaubnis der Sony Corporation.

12

Anda mungkin juga menyukai