Service Guide
Service guide files and updates are available on the ACER/CSD web; for more information, please refer to http://csd.acer.com.tw
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates made on Aspire 3020/5020 service guide.
Date
Chapter
Updates
II
Copyright
Copyright 2005 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice. Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation. Intel is a registered trademark of Intel Corporation. Pentium and Pentium II/III are trademarks of Intel Corporation. Other brand and product names are trademarks and/or registered trademarks of their respective holders.
III
Conventions
The following conventions are used in this manual: SCREEN MESSAGES NOTE Denotes actual messages that appear on screen. Gives bits and pieces of additional information related to the current topic. Alerts you to any damage that might result from doing or not doing specific actions. Gives precautionary measures to avoid possible hardware or software problems. Reminds you to do specific actions relevant to the accomplishment of procedures.
WARNING
CAUTION
IMPORTANT
IV
Preface
Before using this information and the product it supports, please read the following general information. 1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such cases, please contact your regional offices or the responsible personnel/channel to provide you with further technical details. Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on your regional web or channel. If, for whatever reason, a part number change is made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and service of customer machines.
2.
VI
Chapter 1
System Specifications
Features
Below is a brief summary of the computers many feature:
Display
Thim-Film Transistor (TFT) displaying at : 15.0 XGA (1024 x 768) 15.0 SXGA+ (1400 x 1050) 15.4 WXGA (1280 x 800) 15.4 WXGA+ (1680 x 1050) ATI MOBILITYTM RADEONTM X600 or ATI MOBILITYTM RADEONTM X700 Simultaneous display on LCD and CRT display DualViewTM support MPEG-2/DVD hardware-assisted capability
Storage subsystem
One 40 GB or harger hard disk drive Optical drive options: DVD-Super Multi DVD-Dual DVD/CD-RW combo 6-in-1 card reader (MS/MS PRO/MMC/SD/SM/xD-Picture Card
Input devices
88/89-key keyboard Touchpad with 4-way integrated scroll button Six easy-launch buttons
Chapter 1
Audio
Audio system with two built-in speakers MS-Sound compatible
Communication
Modem: 56K ITU V.90/V.92 modem with PTT approval; wake-on ring ready LAN: 10/100/1000 Mbps Fast Ethernet (for selected models); wake-on-LAN ready WLAN (manufacturing option): integrated 802.11b/g dual band (for selected models), or 802.11a/b/ g tri-mode WI-Fi CERTIFIEDTM WLAN solution (for selected models); Acer SignalUp wireless technology support WPAN (manufacturing option): integrated Bluetooth
I/O Ports
Four USB 2.0 ports IEEE 1394 port Ethernet (RJ-45) port Modem (RJ-11) port Extternal display (VGA) port S-video/TV-out port Microphone/line-in jack Headphones/speaker/line-out port Infrared (FIR) port Type II PC Card slot 6-in-1 card reader DC-in jack for AC adaptor
Chapter 1
91.4C501.001 (04243)
200-PIN DDR SODIMM
AMD CPU
35W/25W
4,5,6,7
Dummy when use 'UMA' Dummy when use 'DIS' Dummy when use 'SATA' Dummy when use 'IDE' Dummy when use ''M26' Dummy when use ''M24'
DDR 333/400
DDR x2
8,9,10
SVIDEO/COMP
TVOUT 16
L1: Signal 1 L2:VCC L3: Signal 2 L4: Signal 3 L5: GND L6: Signal 4
Power Block Diag -> Page 40
ATI
TI PCI 7411
1* Slot Cardbus 1* 1394 CardReader
LVDS
LCD 17
RS480M
AGTL+ CPU I/F + UMA 11,12,13,14 PCI Express x16
ATI M26/M24
50,51,52
RGB CRT
CRT 16
C
SM/MMC/SD
1394 4pin Conn 28
5 in 1
28 26,27
PCI-Express x2
CH7307C 15
TMDS
VRAM x4
(M26/M24 diff.) 53,54
ATI
Mini-PCI 802.11a/b/g
31 PCI Bus / 33MHz PCI
SB400
ACPI 2.0 6xUSB 2.0
USB x 4
24 AC97
24
RJ45
30
TXFM
30
1000Mb
TXFM
30
10/100Mb
32
30
OP AMP G1421 33
PIDE
SIDE
NS SIO PC87392
37
KBC KB3910
34
XBUS
SATA
25
HDD
25
DVD/ CD-RW
25
FIR
Touch Pad
37 35
Int. KB
ISA ROM
36
35
<Variant Name>
SEARIAL PORT
CRT
PRINTER
4
Title
BLOCK DIAGRAM
Size A3 Document Number
Bolsena
Sheet
1
Rev SB 1 of 58
Chapter 1
Board Layout
Top View
1 2 3 4 5 6
Keyboard Connector Bluetooth Board Connector LCD Cable Connector LED Board Connector Lid Switch Modem Cable Connector
7 8 9 10 11
3 in 1 Connector Speaker Connector Internal Microphone Connector Modem Board Connector Touchpad Board Connector
Chapter 1
Bottom View
1 2 3 4 5 6 7 8 9 10 11 12
Power Jack CRT Docking Audio Cable Connector Main Battery Connector ODD Connector Media Bay Connector Mini PCI Slot Second Battery Connector RTC Battery Connector DDR DIMM Connector HDD Connector
16 17 18 19 20 21 22 23 24 25 26 27
Audio Cable Connector Line-in Connector Headphone Out Connector Microphone-in Connector USB Connector IEEE 1394 Connector PCMCIA USB Connector CPU Socket USB Connector S-Video RJ45 and RJ11 Connector
Chapter 1
13 14 15
28 29 30
Chapter 1
An Aspire tour
After knowing your computer features, let us show you around your new TravelMate computer.
Just for Starters...
Front View
Item
Description
# 1 2 3 4 5 6
Icon
Item Display screen Power button Microphone Keyboard Touchpad Click buttons (left, center and right) Launch keys Status indicators
Description Also called LCD (liquid-crystal display), displays computer output. Turns the computer on and off. Internal microphone for sound recording. For entering data into your computer. Touch-sensitive pointing device which functions like a computer mouse. The left and right buttons function like the left and right mouse buttons; the center button serves as a 4-way scroll button. Buttons for launching frequently used programs. Light-Emitting Diodes (LEDs) that turn on and off to show the status of the computers function and components. Comfortable support area for our hands when you use the computer.
7 8
Palmrest
Chapter 1
# 1 2
Icon Icon
Item
Item
Description
Description
Speakers Bluetooth communication button/ indicator Wireless communication button/ indicator Line-in/mic-in jack
Left and right speakers deliver stereo audio output. Press to enable/disable Bluetooth function. Lights to indicate the status of Bluetoothcommunications (manufacturing option). Press to enable/disable Wireless function. Lights to indicate the status of wireless LAN communications. (manufacturing option). Accepts input from external microphones.
Battery indicator
Power indicator
Latch
Chapter 1
Icon
Item
Description
Left View
# 1 2
Icon Icon
Item
Item
Description
Description
Enable the computer to stay cool, even after prolonged use. Connects to a television or display device with S-video input (manufacturing option). Connects to IEEE 1394 devices (manufacturing option). Connects to USB 2.0 devices (e.g., USB mouse, USB camera). Interfaces with infrared devices like infrared printer and IR-aware computer (manufacturing option). Connects to one Type II PC Card.
Infrared port
PC Card slot
Note:
7 6-in-1 card reader Accepts and MS, MS PRO, MMC, SD, SM or xD-Picture card (manufacturing option). Note: Only one card can operate at any given time.
Right View
Item
Description
Icon
Item
Description
Chapter 1
Item
Description
1 2 3
Optical drive eject button Optical disk access indicator Optical drive
Ejects the optical drive tray from the drive. LED that indicates when an optical disk is being read or written. Internal optical drive; accepts CDs or DVDs depending on the optical drive type.
Note:
Rear Panel
Icon
Item
Description
# 1
Icon
Power jack
Connects to an AC adaptor.
Network jack
Ventilation slots
10
Chapter 1
Icon
Item
Description
Bottom Panel
Item
Description
# 1 2 3 4 5
Item Wireless LAN bay Battery lock Battery release latch Battery bay Cooling fan
Description Houses the computers wireless LAN. Locks the battery in place. Releases the battery for removal. Houses the computers battery pack. Helps keep the computer cool. Note Note: Do not cover or obstruct the opening of the fan. Houses the computers main memory and hard disk (secured by a screw).
Indicators
The computer has four easy-to-read status indicators on the upper-right above the keyboard, and four on the front panel.
The power, battery and wireless communication status indicators are visible even when the LCD display is closed.
Chapter 1
11
Icon
Num lock
Media Activity
Bluetooth
Wireless LAN
Power
Battery
NOTE: 1. Charging: The light shows amber when the battery is charging. 2. Fully charged: The light shows green when in AC mode.
Launch Keys
Located at the upper-right, above the keyboard are four buttons. These buttons are called launch keys. The are: mail, Web browser, Acer Empowering key and one user-programmable button.
Press to ru the Acer eManager. Please see Acer eManager. The mail and Web buttons are pre-set to email and Internet programs, but can be reset by users. To set the Web browser, mail and programmable keys, run the Acer Launch Manager.
12
Chapter 1
Default application Email application (user-programmable) Internet browser (user-programmable) Acer eManager (user-programmable)
User-programmable
Touchpad
The built-in touchpad is a pointing device that senses movement on its surface. This means the cursor responds as you move your finger across the surface of the touchpad. The central location on the palmrest provides optimum comfort and support.
Touchpad Basics
The following teaches you how to use the touchpad:
Chapter 1
13
Move your finger across the touchpad (2) to move the cursor. Press the left (1) and right (4) buttons located beneath the touchpad to perform selection and execution functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on the touchpad is the same as clicking the left button. Use the 4-way scroll (3) button to scroll up or down and move left or right a page. This button mimics your cursor pressing on the right scroll bar of Windows applications.
Function Execute
Main touchpad (2) Tap twice (at the same speed as doubleclicking the mouse button) Tap once Tap twice (at the same speed as doubleclicking a mouse button) then hold finger to the touchpad on the second tap to drag the cursor.
Select Drag
Click once Click and hold, then use finger to drag the cursor on the touchpad
NOTE: Keep your fingers dry and clean when using the touchpad. Also keep the touchpad dry and clean. The touchpad is sensitive to finger movements. Hence, the lighter the touch, the better the response. Tapping too hard will not increase the touchpads responsiveness.
14
Chapter 1
Description When Caps Lock is on, all alphabetic characters typed are in uppercase. When Num Lock is on, the embedded keypad is in numeric mode. The keys function as a calculator (complete with the arithmetic operators +, -, *, and /). Use this mode when you need to do a lot of numeric data entry. A better solution would be to connect an external keypad. When Scroll Lock is on, the screen moves one line up or down when you press the up or down arrow keys respectively. Scroll Lock does not work with some applications.
The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols are not printed on the keys.
Desired Access Number keys on embedded keypad Cursor-control keys on embedded keypad Main keyboard keys
Num Lock On Type numbers in a normal manner. Hold <Shift> while using cursor-control keys. Hold <Fn> while typing letters on embedded keypad.
Hold <Fn> while using cursor-control keys. Type the letters in a normal manner.
Windows Keys
The keyboard has two keys that perform Windows-specific functions.
Chapter 1
15
Icon
Description Pressed alone, this key has the same effect as clicking on the Windows Start button; it launches the Start menu. It can also be used with other keys to provide a variety of function: + <Tab> Activates next taskbar button. + <E> Opens the My Computer window + <F1> Opens Help and Support. + <F> Opens the Find: All Files dialog box. + <R> Opens the Run dialog box. + M Minimizes all windows. <Shift>+ action. + <M> Undoes the minimize all windows
Application key
This key has the same effect as clicking the right mouse button; it opens the applications context menu.
Hot Keys
The computer employs hotkeys or key combinations to access most of the computers controls like sreen brightness, volume output and the BIOS utility. To activate hot keys, press and hold the <Fn> key before pressing the other key in the hotkey combination.
Icon
Fn-F2
Acer eSetting
Fn-F3
Acer ePowerManagement
16
Chapter 1
Icon Sleep
Function
Fn-F5
Display toggle
Switches display output between the display screen, external monitor (if connected) and both.
Fn-F6
Screen blank
Turns the display screen backlight off to save power. Press any key to return.
Fn-F7
Touchpad toggle
Fn-F8
Speaker toggle
Fn-w
Volume up
Fn-y
Volume down
Fn-x
Brightness up
Fn-z
Brightness down
Special Key
You can locate the Euro symbol and US dollar sign at the upper-center and/or bottom-right of your keyboard. To type:
Chapter 1
17
18
Chapter 1
BIOS
Item BIOS vendor BIOS Version BIOS ROM type BIOS ROM size BIOS package Supported protocols Phneoix 3A03 SST 39SF040A, 512KX8 CMOS Boot Block Flash Memory 512KB 32-pin PLCC ACPI 1.0b, PC Card 95, SM BIOS 2.3, IEEE1284-ECP/EPP, PCI 2.2, PnP 1.0a, DMI 2.0, PS/2 keyboard and mouse, USB 2.0, VGA BIOS, CD-ROM bootable, IEEE 1394 Set by setup manual Specification
System Memory
Item Memory controller Memory size DIMM socket number Supports memory size per socket Supports maximum memory size Supports DIMM type Supports DIMM Speed AMD CPU built-in 0MB (no on-board memory) 2 sockets 1024MB 2G (by two 1024MB SO-DIMM module) DDR Synchronous DRAM 333 MHz Specification
Chapter 1
19
System Memory
Item Supports DIMM voltage Supports DIMM package Memory module combinations 2.5V and 1.25V 200-pin soDIMM You can install memory modules in any combinations as long as they match the above specifications. Specification
Memory Combinations
Slot 1 0MB 0MB 0MB 0MB 128MB 128MB 128MB 1284MB 256MB 256MB 256MB 256MB 512MB 512MB 512MB 512MB 1024MB 1024MB 1024MB 1024MB 1024MB 128MB 256MB 512MB 1024MB 128MB 256MB 512MB 1024MB 128MB 256MB 512MB 1024MB 128MB 256MB 512MB 1024MB 0MB 128MB 256MB 512MB 1024MB Slot 2 128MB 256MB 512MB 1024MB 256MB 384MB 640MB 1152MB 384MB 512MB 768MB 1280MB 640MB 768MB 1024MB 1536MB 1024MB 1125MB 1280MB 1536MB 2048MB Total Memory
NOTE: Above table lists some system memory configurations. You may combine DIMMs with various capacities to form other combinations. On above table, the configuration of slot 1 and slot 2 could be reversed. LAN Interface
Item Chipset Supports LAN protocol LAN connector type LAN connector location Features 10/100/1000Mbps RJ45 Rear side Integrated 10/100 BASE-T transceiver Wake on LAN support compliant with ACPI 2.0 PCI v2.2 Specification Realtek RTC8110SBL(10/100/1000M) ; RTL8100C(10/100M)
IR Interface
Item Part name Package VISHAY TFU6102F 8-pin SMT type Specification
20
Chapter 1
IR Interface
Item Performance Compliant 4Mbit/s IrDA 1.1 Specification
Modem Interface
Item Data modem data baud rate (bps) Supports modem protocol Modem connector type Modem connector location 56K V.90/V.92 RJ11 Rear side Specification
Bluetooth Interface
Item Chipset Data throughput Protocol Interface Connector type built-in ATI SB400 723 bps (full speed data rate) Bluetooth 1.1 (Upgradeable to Bluetooth 1.2 when SIG specification is ratified). USB 1.1 Mini-USB Specification
Chapter 1
21
Performance Specifications 2048KB ATA/ATAPI-6; ATA-6 372 8192KB ATA/ATAPI-6; ATA-6 350 8192KB ATA/ATA-6; ATA-6 350
Loading mechanism
DVD-Dual Interface
Item Vendor & model name Performance Specification DVD Dual HLDS GWA-4040N With CD Diskette With DVD Diskette Specification
22
Chapter 1
DVD-Dual Interface
Item Transfer rate (KB/sec) Buffer Memory Interface Applicable disc format Sustained: Max 3.6Mbytes/sec 2MB Enhanced IDE(ATAPI) compatible Support disc formats 1. Reads data in each CD-ROM, CD-ROM XA, CD-1, Video CD, CD-Extra and CD-Text 2. Reads data in Photo CD (single and Multi-session) 3. Reads standard CD-DA 4. Reads and writes CD-R discs 5. Reads and writes CD-RW discs 6. Reads and writes in each dVD+R/RW (Ver. 1.1) 7. Reads data in each DVD-ROM and DVD-R (Ver. 2.0 for Authoring) 8. Reads and writes in each DVD-R (Ver. 2.0 for general), DVD-RW and DVD+R/RW (Ver1.1) Load: Manual Release: (a) Electrical Release (Release Button) (b) Release by ATAPI command (c) Emergency Release 5 V +/- 5 % (Operating) Specification Sustained: Max 10.8Mbytes/sec
Loading mechanism
Audio Interface
Item Audio Controller Audio onboard or optional Mono or Stereo Resolution Compatibility Mixed sound source Voice channel Sampling rate Internal microphone Internal speaker / Quantity ALC655 Built-in Stereo 18 bit stereo digital to analog converter 18 bit stereo analog to digital converter AC97 Line-in, CD 8/16-bit, mono/stereo 44,1 KHz (48K byte for AC97 interface) Yes Yes/2 Specification
Video Interface
Item Chipset Package Interface Supports ZV (Zoomed Video) port Specification ATI Mobility RADEON X700 MBGA 708 pin PCIE x16 Yes
Chapter 1
23
Video Memory
Item Chipset Memory size Interface
USB Port
Item Chipset USB Compliancy Level OHCI Number of USB port Location Serial port function control ATI SB400 2.0 USB 1.1 and USB 2.0 Host controller 4 three on the left side; one on the rear side Enable/Disable by BIOS Setup Specification
PCMCIA Port
Item PCMCIA controller Supports card type Number of slots Access location Supports ZV (Zoomed Video) port Supports 32 bit CardBus TI PCI7411 Type-II One type-II Left panel No ZV support Yes Specification
24
Chapter 1
Keyboard
Item Keyboard controller Total number of keypads Windows logo key Internal & external keyboard work simultaneously KB 3910 88-/89-key Yes 1. Plug USB keyboard to the USB port directly: Yes 2. Use port replicator then plug a USB/PS 2 keyboard to the USB port/PS 2 port on the port replicator: Yes Specification
Battery
Item Vendor & model name Battery Type Pack capacity Number of battery cell Package configuration Normal voltage Charge voltage Specification Sanyo 4UR18650F-2-QC140 Panasonic CGR-B/8B5AE Li-ion 4400 mAh 8 4 cells in series, 2 series in parallel 14.4V 16.8+-0.2v
LCD 15 inch
Item Vendor & model name Screen Diagonal (mm) Active Area (mm) Display resolution (pixels) Pixel Pitch Pixel Arrangement Display Mode Typical White Luminance (cd/m2) also called Brightness Specification AU: B150XG01 381 304.1x228.1 1024x768 XGA 0.297x0.297 R.G.B. Vertical Stripe Normally White 180 (5 point average) 150 (5 point average) N/A 300 24/11 15/35 +3.3V Typ. +3.3V 3.3V N/A 300 8/17 70 250 10/25 QDI QD15XL06-01 15.0 inches 304.1x228.1 1024x768 XGA 0.099x0.297 R.G.B. Vertical Stripe Normally White 160 Hannstar HSD150PX14-A07 15.0 inches 304.1x228.1 1024x768 XGA 0.297x0.297 R.G.B. Vertical Stripe Normally White 150
Luminance Uniformity Contrast Ratio Response Time (Optical Rise Time/Fall Time)msec Nominal Input Voltage VDD
Chapter 1
25
LCD 15 inch
Item Typical Power Consumption (watt) Weight Physical Size(mm) Electrical Interface Support Color Viewing Angle (degree) Horizontal: Right/Left Vertial: Upper/Lower Temperature Range( C) Operating Storage (shipping) 0 to +50 -20 to +60 0 to +50 -25 to +60 0 to +50 -20 to +60 40/40 10/30 45/45 15/35 40/40 20/40 Specification 5.6/5.7 550 317.3x242.0x6.0 1 channel LVDS 262K colors (RGB 6-bit data driver) 3.96 570 317.3x242.0x5.9 1 channel LVDS 262,144 N/A 600 317.3x242.0x6.5 1 channel LVDS 262,144
26
Chapter 1
LCD Inverter
Item Vendor & model name Brightness conditions Input voltage (V) Input current (mA) Output voltage (V, rms) Output current (mA, rms) Output voltage frequency (k Hz) SUMIDA TWS-449-147 Vadj=3.3V 8~20 350 (max) 1600 (no load) 5.6~5.4 55~58K Hz Specification
AC Adaptor
Item Input rating Maximum input AC current Inrush current Efficiency 1.7A 220A@115VAC 220A@230VAC 82% min. @115VAC input full load Specification 90V AC to 264V AC, 47Hz to 63Hz
Chapter 1
27
28
Chapter 1
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computers BIOS (Basic Input/ Output System). Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 Troubleshooting when problem arises. To activate the BIOS Utility, press m during POST (when Press <F2> to enter Setup message is prompted on the bottom of screen). Press m to enter setup. The default parameter of F12 Boot Menu is set to disabled. If you want to change boot device without entering BIOS Setup Utility, please set the parameter to enabled. Press <F12> during POST to enter multi-boot menu. In this menu, user can change boot device without entering BIOS SETUP Utility.
Mobile AMD Sempron(tm) ProcesIntel (R) Celeron (R) M processor CPU Type : 1.80 GHz CPU Speed : HDD Model Name : ST960821A - (PM) HDD Serial Number : None ATAPI Model Name : TSSTcorpCD/DVDW TS-LS32A - (SM) ATAPI Serial Number : None System BIOS Ver: V0.06A BK-ATI VER008.025M.000.000 VGA BIOS Ver 01.17 KBC Ver xxxxxxxxxxxxxxxxxxxxxx Serial Number 22 Byte Asset Tag Number N/A 32 Byte Product Name TravelMate 4400 16 Byte Manufacturer Name: Acer UUID: xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx 16 Byte 32 Byte
F1
Help
Esc Exit
Chapter 2
29
30
Chapter 2
Information
PhoenixBIOS Setup Utility . Info. Main Advanced Security Boot Exit
Mobile AMD Sempron(tm) ProcesIntel (R) Celeron (R) M processor CPU Type : 1.80 GHz CPU Speed : HDD Model Name : ST960821A - (PM) HDD Serial Number : None ATAPI Model Name : TSSTcorpCD/DVDW TS-LS32A - (SM) ATAPI Serial Number : None System BIOS Ver: V0.06A BK-ATI VER008.025M.000.000 VGA BIOS Ver 01.17 KBC Ver xxxxxxxxxxxxxxxxxxxxxx Serial Number 22 Byte Asset Tag Number N/A 32 Byte Product Name TravelMate 4400 16 Byte Manufacturer Name: Acer UUID: xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx 16 Byte 32 Byte
F1
Help
Esc Exit
Parameter Floppy Disk Drive HDD Model Name HDD Serial Number ATAPI Model Name ATAPI Serial Number System BIOS ver VGA BIOS Ver KBC Ver Serial Number Asset Tag Number Product Name Manufacturer Name UUID Number
Description Shows floppy drive type informaiton only when this model has floppy disk drive. This field shows the model name of HDD installed on primary IDE master. This field displays the serial number of HDD installed on primary IDE master. This field displays the mofel name of devices installed on secondary IDE master. The hard disk drive or optical drive model name is automatically detected by the system. This field shows the serial number of devices installed on secondary IDE master. Displays system BIOS version. This field displays the VGA firmware version of the system. This field shows the keyboard This field displays the serial number of this unit. This field displays the asset tag number of the system. This field shows product name of the system. This field displays the manufacturer of this system. This will be visible only when an internal LAN device is presenting. UUID=32bytes
Chapter 2
31
Main
The Main screen displays a summary of your computer hardware information, and also includes basic setup parameters. It allows the user to specify standard IBM PC AT system parameters.
Item Specific Help System Time: System Date: System Memory: Extended Memory: Video Memory Quiet Boot: Power on display: LCD Auto Dim Network boot F12 Boot Menu D2D Recovery [15:56:48] [04/01/2005] 640 KB 477 MB [32 MB] <Tab>, <Shift-Tab>, or <Enter> selects field. Shows system base memory size Shows extended memory size VGA memory size
NOTE: The screen above is for your reference only. Actual values may differ.
32
Chapter 2
The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings.
Description Sets the system time. The hours are displayed with 24-hour format. Sets the system date.
Format/Option Format: HH:MM:SS (hour:minute:second) System Time Format MM/DD/YYYY (month/day/ year) System Date
This field reports the memory size of the system. Memory size is fixed to 640MB This field reports the memory size of the extended memory in the system. Extended Memory size=Total memory size-1MB Shows the VGA memory size. VGA Memory size=64/128MB Determines if Customer Logo will be displayed or not; shows Summary Screen is disabled or enabled. Enabled: Customer Logo is displayed, and Summary Screen is disabled. Disabled: Customer Logo is not displayed, and Summary Screen is enabled. Option: Enabled or Disabled
Power on display
Auto: During power process, the system will detect if any display device is connected on external video port. If any external display device is connected, the power on display will be in CRT (or projector) only mode. Otherwise it will be in LCD only mode. Both: Simultaneously enable both the integrated LCD screen and the systems external video port (for an external CRT or projector).
Determines if the system will automatically dim the LCD brightness in order to save power when AC is not present. The system will support an automatic dimming of the LCD backlight when the AC power is NOT available (running on battery power).
Enables, disables the system boot from LAN (remote server). Enables, disables Boot Menu during POST. Enables, disables D2D Recovery function. The function allows the user to create a hidden partition on hard disc drive to store operation system and restore the system to factory defaults.
NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is because the user is not allowed to control the settings in these cases.
Chapter 2
33
Advanced
The Advanced menu screen contains parameters involving your hardware devices. It also provides advanced settings of the system.
Configure Infrared Port using options: [Disable] No configuration [Enabled] User configuration
[Disabled] [Disabled]
[Enabled]
F1
Help
Esc Exit
The table below describes the parameters in the screen. Settings in boldface are the default and suggested parameter settings. .
Description Enables, disables or auto detects the infrared port. Sets the I/O address of the infrared port. Sets the interrupt request of the infrared port. Sets a DMA channel for the printer to operate in ECP mode. This parameter is enabled only if Mode is set to ECP. Enables. disables or auto detects the serial port A. Enables, disables or auto detects the parallel port.
Options
Enabled/Disabled/Auto Enabled/Disabled/Auto
34
Chapter 2
Description Enables, disables USB interface devices support. (Enable for use with a non-USB aware Operating System such as DOS or UNIX).
Chapter 2
35
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized use.
Info.
Main
Exit
Item Specific Help User Password is : Supervisor Password is : Set Supervisor Password Set User Password Password on Boot Clear Clear [Enter] [Enter] Supervisor Password controls accesses of the whole setup utility. It can be used to boot up when Password on boot is enabled.
[Disabled]
F1
Help
Esc Exit
36
Chapter 2
The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings.
Description Shows the setting of the user password. Shows the setting of the Supervisor password Press Enter to set the user password. When user password is set, this password protects the BIOS Setup Utility from unauthorized access. The user can enter Setup menu only and does not have right to change the value of parameters. Press Enter to set the supervisor password. When set, this password protects the BIOS Setup Utility from unauthorized access. The user can not either enter the Setup menu nor change the value of parameters. Defines whether a password is required or not while the events defined in this group happened. The following sub-options are all requires the Supervisor password for changes and should be grayed out if the user password was used to enter setup.
Option
Password on Boot
Disabled or Enabled
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Dont forget your password. If you forget your password, you may have to return your notebook computer to your dealer to reset it.
Setting a Password
Follow these steps as you set the user or the supervisor password: 1. Use the w andy keys to highlight the Set Supervisor Password parameter and press the e key. The Set Supervisor Password box appears:
2.
Type a password in the Enter New Password field. The password length can not exceeds 8 alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the Confirm New Password field.
IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen. 3. 4. 5. Press e. After setting the password, the computer sets the User Password parameter to Set. If desired, you can opt to enable the Password on boot parameter. When you are done, press u to save the changes and exit the BIOS Setup Utility.
Removing a Password
Follow these steps: 1. Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The Set Password box appears: 37
Chapter 2
2. 3. 4.
Type the current password in the Enter Current Password field and press e. Press e twice without typing anything in the Enter New Password and Confirm New Password fields. The computer then sets the Supervisor Password parameter to Clear. When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.
Changing a Password
1. Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The Set Password box appears:
2. 3. 4. 5. 6.
Type the current password in the Enter Current Password field and press e. Type a password in the Enter New Password field. Retype the password in the Confirm New Password field. Press e. After setting the password, the computer sets the User Password parameter to Set. If desired, you can enable the Password on boot parameter. When you are done, press u to save the changes and exit the BIOS Setup Utility.
The password setting is complete after the user presses u. If the current password entered does not match the actual current password, the screen will show you the Setup Warning.
38
Chapter 2
If the new password and confirm new password strings do not match, the screen will display the following message.
Chapter 2
39
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.
Item Specific Help +Hard Drive Floppy Devices CD-ROM/DVD Drive Network Boot
Use <> or <> to select a device, the press <F6> to move it up the list, or <F5> move it down the list. Press <ESC> to escape the menu
F1
Help
Esc Exit
40
Chapter 2
Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
Item Specific Help Exit Saving Changes Exit Dicarding Changes Load Setup Defaults Discard Changes Save Changes Exit System Setup and save your changes to CMOS.
F1
Help
Esc Exit
Parameter Exit Saving Changes Exit Discarding Changes Load Setup Default Discard Changes Save Changes
Description Exit System Setup and save your changes to CMOS. Exit utility without saving setup data to CMOS. Load default values for all SETUP item. Load previous values from CMOS for all SETUP items. Save Setup Data to CMOS.
Chapter 2
41
42
Chapter 2
Chapter 3
Chapter 3
43
General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following: 1. 2. 3. Turn off the power to the system and all peripherals. Unplug the AC adapter and all power and signal cables from the system. Remove the battery pack.
44
Chapter 3
Start
Battery
*1 Keyboard
*4 LCD Module HDD Bracket *1 *13 *3 Upper Case Assembly Bluetooth Module
*4
HDD
Touchpad Assembly
Speaker Set
*6 VGA Heatsink
*3 CPU Heatsink
*2 Modem Board
Touchpad Bracket
Touchpad
ODD
ODD Bracket
Chapter 3
45
LCD Module
4 screw caps
*4 LCD Bezel
*2
*2 LCD Inverter
LCD Panel
LCD Assembly
*8
LCD
LCD Brackets
Screw List
Item A B C D E F G H I J K L M N Description SCW HEX NYL I#R-40/O#4-40 L5.5 SCREW MACH WAFER M2*L4 NI CPU SCREW M2.5*6.5 (2.7KG) CPU SCREW M2.5*6.5 (4.5KG) SCRW WH MS+CBZ M2.5+L4 BLACK SCREW M2.5-6 SCREW M2*3 NYLON 1JMCPC-420325 SCREW M2.5X6 SCREW M2-3 SCRW M2.5*L3(NON NYLOK) SCREW M2.5-5 SCREW M3x4(86.9A524.4R0) SCREW WAFER NYLOK NI 2ML3 SCREW NI M2*6L
46
Chapter 3
Chapter 3
47
Removing the Memory/the HDD Module/the Wireless LAN Card/the ODD Module and the LCD Module
Removing the Memory and the HDD Module
1. 2. Remove the three screws fastening the DIMM/HDD cover. Detach the DIMM/HDD cover carefully.
3. 4. 5.
Pop out the memory then remove it. Remove four screws fastening the HDD module. Pull the HDD module backwards then detach it.
3. 4.
Disconnect the main and the auxiliary antennae. Pop out the wireless LAN card then remove it.
48
Chapter 3
3. 4. 5. .
Remove the screw holding the keyboard. Turn over the keyboard as shown. Disconnect the keyboard cable then remove the keyboard.
6.
Pull out the wireless LAN antenna from the main unit as shown.
Chapter 3
49
7.
Take out the LCD cable from the main unit then disconnect the cable.
8. 9. .
Remove two screws fastening the LCD module. Remove another two screws on the bottom as shown.
50
Chapter 3
3. 4.
Remove one screw holding the upper case and the lower case assembly. Then remove 13 screws on the bottom as shown.
5. 6. 7.
Open the upper case assembly as shown. After you open the upper case assembly, please disconnect the lid switch cable. Raise upright the upper case assembly as shown then detach it.
Chapter 3
51
3. 4.
Detach the touchpad bracket carefully. Then detach the touchpad from the touchpad bracket.
4. 5. 6.
Remove three screws fastening the fan to the lower case. Remove two hex screws holding the main board on the rear side. Then take out the main board from the lower case carefully.
7. 52
8. 9.
Disconnect the modem board cable from the main board. Remove the two screws holding the modem board.
10. Disconnect the modem board from the main board then remove it. 11. Disconnect the modem cable from the modem board. 12. Remove the three screws holding the CPU heatsink.
13. Remove the CPU heatsink from the main board. 14. Use a flat headed screwdriver to release the CPU socket lock (see the picture on the middle and on the right).
15. Remove the CPU from the socket carefully. 16. Remove the six screws fastening the VGA heatsink. 17. Then remove the VGA heatsink from the main board.
Chapter 3
53
18. Remove the three screws fastening the speaker set. 19. Tear off the tape holding the speaker set. 20. Take out the speaker set from the lower case. This completes main unit disassembly.
54
Chapter 3
4. 5. 6.
Remove the two screws fastening the LCD inverter. Take out the LCD inverter from the LCD cover, then disconnect the LCD cable from the inverter. Disconnect the inverter cable and remove the inverter.
7. 8. 9. .
Remove two screws fastening the LCD assembly. Take out the LCD assembly from Remove another screw holding the LCD bracket on the other side. Remove the four screws fastening the LCD left bracket then remove it.
10. Remove the four screws fastening the LCD right bracket then remove the bracket. 11. Disconnect the LCD cable from the LCD then remove the cable.
Chapter 3
55
56
Chapter 3
Chapter 4
Troubleshooting
Use the following procedure as a guide for computer problems. NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses. 1. 2. 3. Obtain the failing symptoms in as much detail as possible. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating the same operation. Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified) Power failure. (The power indicator does not go on or stay on.) POST does not complete. No beep or error codes are indicated. POST detects an error and displayed messages on screen. Other symptoms (i.e. LCD display problems or others). Symptoms cannot be re-created (intermittent problems).
Go To Power System Check on page 59. Power-On Self-Test (POST) Error Message on page 62 Undetermined Problems on page 74 Error Message List on page 63 Power-On Self-Test (POST) Error Message on page 62 Use the customer-reported symptoms and go to Power-On Self-Test (POST) Error Message on page 62 Intermittent Problems on page 73 Undetermined Problems on page 74
Chapter 4
57
If an error occurs with the internal diskette drive, reconnect the diskette connector on the system board. If the error still remains: 1. 2. 3. Reconnect the external diskette drive/DVD-ROM module. Replace the external diskette drive/CD-ROM module. Replace the main board.
If an error occurs, reconnect the connector on the System board. If the error still remains:
The following auxiliary input devices are supported by this computer: Numeric keypad External keyboard 58 Chapter 4
If any of these devices do not work, reconnect the cable connector and repeat the failing operation.
Memory check
Memory errors might stop system operations, show error messages on the screen, or hang the system. 1. 2. 3. Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board. Go to the diagnostic memory in the test items. Press F2 in the test items.
4. Follow the instructions in the message window. NOTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.
If you suspect a power problem, see the appropriate power supply check in the following list:
Chapter 4
59
1. 2.
If the voltage is not correct, replace the power adapter. If the voltage is within the range, do the following: Replace the System board. If the problem is not corrected, see Undetermined Problems on page 74.
If the voltage is not correct, go to the next step. NOTE: An audible noise from the power adapter does not always indicate a defect. 3. 4. If the power-on indicator does not light up, check the power cord of the power adapter for correct continuity and installation. If the operational charge does not work, see Check the Battery Pack on page 61.
60
Chapter 4
From Hardware:
3.
If the voltage is still less than 7.5 Vdc after recharging, replace the battery.
To check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. If the battery status indicator does not light up, remove the battery pack and let it return to room temperature. Re-install the battery pack. If the charge indicator still does not light up, replace the battery pack. If the charge indicator still does not light up, replace the DC/DC charger board.
Touchpad Check
If the touchpad doesnt work, do the following actions one at a time to correct the problem. Do not replace a non-defective FRU: 1. 2. 3. Reconnect the touchpad cables. Replace the touchpad. Replace the system board.
After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement can occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware problem. No service actions are necessary if the pointer movement stops in a short period of time.
Chapter 4
61
62
Chapter 4
Chapter 4
63
64
Chapter 4
Chapter 4
65
66
Chapter 4
Code 46h 48h 49h 4Ah 4Bh 4Ch 4Eh 50h 51h 52h 54h 58h 59h 5Ah 5Bh 5Ch 60h 62h 64h 66h 67h 68h 69h 6Ah 6Bh 6Ch 6Eh 70h 72h 76h 7Ch 7Eh 80h 81h 82h 83h 84h 85h 86h 87h 88h 89h 8Ah 8Bh 2-2-3-1 2-1-2-3
Beeps
POST Routine Description Check ROM copyright notice Check video configuration against CMOS Initialize PCI bus and devices Initialize all video adapters in system QuietBoot start (optional) Shadow video BIOS ROM Display BIOS copyright notice Display CPU type and speed Initialize EISA board Test keyboard Set key click if enabled Test for unexpected interrupts Initialize POST display service Display prompt Press F2 to enter SETUP Disable CPU cache Test RAM between 512 and 640 KB Test extended memory Test extended memory address lines Jump to User Patch1 Configure advanced cache registers Initialize Multi Processor APIC Enable external and CPU caches Setup System Management Mode (SMM) area Display external L2 cache size Load custom defaults (optional) Display shadow-area message Display possible high address for UMB recovery Display error messages Check for configuration errors Check for keyboard errors Set up hardware interrupt vectors Initialize coprocessor if present Disable onboard Super I/O ports and IRQs Late POST device initialization Detect and install external RS232 ports Configure non-MCD IDE controllers Detect and install external parallel ports Initialize PC-compatible PnP ISA devices Re-initialize onboard I/O ports Configure Motherboard Configurable Devices (optional) Initialize BIOS Area Enable Non-Maskable Interrupts (NMIs) Initialize Extended BIOS Data Area Test and initialize PS/2 mouse
Chapter 4
67
Code 8Ch 8Fh 90h 91h 92h 93h 95h 96h 97h 98h 99h 9Ah 9Ch 9Dh 9Eh 9Fh A0h A2h A4h A8h AAh ACh AEh B0h B2h B4h B5h B6h B9h BAh BBh BCh BDh BEh BFh C0h C1h C2h C3h C4h C5h C6h C7h C8h C9h 1 1-2
Beeps
POST Routine Description Initialize floppy controller Determine number of ATA drives (optional) Initialize hard-disk controllers Initialize local-bus hard-disk controllers Jump to UserPatch2 Build MPTABLE for multi-processor boards Install CD ROM for boot Clear huge ES segment register Fixup Multi Processor table Search for option ROMs. One long, two short beeps on checksum failure. Check for SMART drive (optional) Shadow option ROMs Set up Power Management Initialize security engine (optional) Enable hardware interrupts Determine number of ATA and SCSI drives Set time of day Check key lock Initialize Typematic rate Erase F2 prompt Scan for F2 key stroke Enter SETUP Clear Boot flag Check for errors POST done- prepare to boot operating system One short beep before boot Terminate QuietBoot (optional) Check password (optional) Prepare Boot Initialize DMI parameters Initialize PnP Option ROMs Clear parity checkers Display MultiBoot menu Clear screen (optional) Check virus and backup reminders Try to boot with INT 19 Initialize POST Error Manager (PEM) Initialize error logging Initialize error display function Initialize system error handler PnPnd dual CMOS (optional) Initialize notebook docking (optional) Initialize notebook docking late Force check (optional) Extended checksum (optional)
68
Chapter 4
Code D2h
Beeps
Code E0h E1h E2h E3h E4h E5h E6h E7h E8h E9h EAh EBh ECh EDh EEh EFh F0h F1h F2h F3h F4h F5h F6h F7h 1
Beeps Initialize the chipset Initialize the bridge Initialize the CPU Initialize the system timer Initialize system I/O Check force recovery boot Checksum BIOS ROM Go to BIOS Set Huge Segment Initialize Multi Processor Initialize OEM special code Initialize PIC and DMA Initialize Memory type Initialize Memory size Shadow Boot Block System memory test Initialize interrupt vectors Initialize Run Time Clock Initialize video Initialize System Management Mode Output one beep before boot Boot to Mini DOS Clear Huge Segment Boot to Full DOS
Chapter 4
69
Indicator-Related Symptoms
Symptom / Error Indicator incorrectly remains off or on, but system runs correctly Inverter board System board Action in Sequence Reconnect the inverter board
Power-Related Symptoms
Symptom / Error Power shuts down during operation Action in Sequence Power source (battery pack and power adapter). See Power System Check on page 59. Battery pack Power adapter Hard drive & battery connection board System board The system doesnt power-on. Power source (battery pack and power adapter). See Power System Check on page 59. Battery pack Power adapter Hard drive & battery connection board System board The system doesnt power-off. Power source (battery pack and power adapter). See Power System Check on page 59. Hold and press the power switch for more than 4 seconds. System board
70
Chapter 4
Power-Related Symptoms
Symptom / Error Battery cant be charged Battery pack System board Action in Sequence See Check the Battery Pack on page 61.
PCMCIA-Related Symptoms
Symptom / Error System cannot detect the PC Card (PCMCIA) PCMCIA slot pin is damaged. PCMCIA slot assembly System board PCMCIA slot assembly Action in Sequence
Memory-Related Symptoms
Symptom / Error Memory count (size) appears different from actual size. Action in Sequence Enter BIOS Setup Utility to execute Load Default Settings, then reboot system. DIMM System board
Speaker-Related Symptoms
Symptom / Error In Windows, multimedia programs, no sound comes from the computer. Internal speakers make noise or emit no sound. Audio driver Speaker System board Speaker System board Action in Sequence
Chapter 4
71
Peripheral-Related Symptoms
Symptom / Error System configuration does not match the installed devices. External display does not work correctly. USB does not work correctly Print problems. Action in Sequence Enter BIOS Setup Utility to execute Load Default Settings, then reboot system. Reconnect hard disk/CD-ROM/diskette drives. Press Fn+F5, LCD/CRT/Both display switching System board System board Ensure the Parallel Port in the Onboard Devices Configuration of BIOS Setup Utility is set to Enabled. Onboard Devices Configuration Run printer self-test. Printer driver Printer cable Printer System Board Serial or parallel port device problems. Ensure the Serial Port in the Devices Configuration of BIOS Setup Utility is set to Enabled. Device driver Device cable Device System board
Keyboard/Touchpad-Related Symptoms
Symptom / Error Keyboard (one or more keys) does not work. Keyboard System board Touchpad does not work. Reconnect touchpad cable. Touchpad board System board Action in Sequence Reconnect the keyboard cable.
Modem-Related Symptoms
Symptom / Error Internal modem does not work correctly. Modem phone port modem combo board System board Action in Sequence
NOTE: If you cannot find a symptom or an error in this list and the problem remains, see Undetermined Problems on page 74.
72
Chapter 4
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists. When analyzing an intermittent problem, do the following: 1. 2. 3. Run the advanced diagnostic test for the system board in loop mode at least 10 times. If no error is detected, do not replace any FRU. If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
Chapter 4
73
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect, whether a short circuit is suspected, or whether the system is inoperative. Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU). NOTE: Verify that all attached devices are supported by the computer. NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See Power System Check on page 59.): 1. 2. 3. Power-off the computer. Visually check them for damage. If any problems are found, replace the FRU. Remove or disconnect all of the following devices: Non-Acer devices Printer, mouse, and other external devices Battery pack Hard disk drive DIMM CD-ROM/Diskette drive Module PC Cards 4. 5. 6. 7. Power-on the computer. Determine if the problem has changed. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU. If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU: System board LCD assembly
74
Chapter 4
Chapter 5
[13]
[17] [18] [21] [22] [23] [24] [25] [26] [27] [29] [30] [32] [19] [20]
[28]
[31]
[33]
[34][35][36][41][37]
[38]
[39][40]
Chapter 5
75
19 (CN17) 21 (U21) 23 (CN19) 25 (U23) 27 (CN20) 29 (CN21) 31 (CN22) 33 (CN24) 35 (CN25) 37 (SW2) 39 (LED2) 41 (U30)
MINI PCI CPU Socket USB Connector EC PC97551 DDR SO-DIMM Socket1 DDR SO-DIMM Socket2 PCMCIA Connector USB Connector Microphone Jack WLAN Button Battery LED Audio Codec ALC203
20 (U20) 22 (CN18) 24 (U22) 26 (BT1) 28 (U25) 30 (U26) 32 (CN23) 34 (CN26) 36 (CN27) 38 (SW3) 40 (LED1) 42 (CN13)
Northbridge M760GX USB Connector BIOS ROM RTC Battery LAN PHY RTL8201CP Southbridge 963L HDD Connector LineOut Jack LineIn Jack Bluetooth button Power LED FAN Connector
76
Chapter 5
Bottom View
[01] [02] [03]
[07]
[09]
Lid Switch LED Board Connector Keyboard Connector Touchpad Board Connector Clock Generator MDC Connector
Panel Connector Modem Connector Bluetooth Module Connector Internal Microphone Connector PCMCIA Connector Internal Speaker Connector
Chapter 5
77
78
Chapter 5
Chapter 6
Chapter 6
79
22 2 7 19 1
10 15
14
4 11 18 13 17
16
20
12 3
5 9
21 6
Acer Incorporated
NS Cable
54.A56V1.001
80
Chapter 6
NS NS NS NS NS NS NS NS NS NS NS CASE/COVER/BRACKET ASSEMBLY 2 5
COVER SWITCH CABLE POWER CABLE 16A 250V 3PIN EUR BK POWER CORD 220V 3PIN EUR POWER CORD 10A 125V 3PIN US BK POWER CORD 10A 125V US POWER CORD 10A 250V 3PIN CHINA POWER CORD 3A 250V 3PIN UK POWER CORD 10A 250V 3PIN BK SOUTH AFRICA POWER CORD 10A 250V SWISS POWER CORD 10A 3PIN DEMARK POWER CORD 10A 250V 3PIN ITALY MIDDLE COVER MINI PCI COVER
50.A46V1.004 27.01518.731 27.T30V1.004 27.01518.641 27.T30V1.001 27.01518.591 27.01518.541 27.01518.571 27.01518.581 27.01518.561 27.01518.611 60.A46V1.003 42.A46V1.001
42.A46V1.002
NS
TOUCHPAD BRACKET
33.A46V1.001
Chapter 6
81
60.A46V1.001
NS
SPEAKER LEFT/RIGHT
23.A46V1.001
60.A46V1.002
NS NS NS DVD-RW Module NS
AMD MOBILE SEMPRON 2800+ 25WD AMD MOBILE SEMPRON 3000+ 25WD AMD MOBILE SEMPRON 3100+ 25WD DVD-RW MODULE 8X DUAL
6M.A46V1.003
82
Chapter 6
NS
KU.00804.015
NS NS NS FAN NS
DVD-RW MODULE 8X DUAL OPTICAL BRACKET DVD-RW 8X TOSHIBA TS-L532A DUAL W/BEZEL FAN
23.A46V1.002
Heatsink NS NS NS CPU HEATSINK CPU HEATSINK CPU HEATSINK 34.A46V1.021 34.A46V1.021 34.A46V1.011
NS
VGA HEATSINK
34.A46V1.002
Chapter 6
83
NS NS NS NS NS NS NS Keyboard 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7
HDD BRACKET HDD 60GB HITACHI C25N060ATMR04 HDD 60GB SEAGATE ST960821A HDD 60GB TOSHIBA MK6025GAS HDD BRACKET HDD 80G HITACHI IC25N080ATMR04 HDD 80G SEAGATE ST9808210A KEYBOARD DARFON NSK-H3M1D US INTERNATIONAL KEYBOARD DARFON NSK-H3M02 CHINESE KEYBOARD DARFON NSK-H3M0S SPANISH KEYBOARD DARFON NSK-H3M03 THAI KEYBOARD DARFON NSK-H3M0U UK KEYBOARD DARFON NSK-H3M0G GERMAN KEYBOARD DARFON NSK-H3M0E ITALIAN KEYBOARD DARFON NSK-H3M0F FRENCH KEYBOARD DARFON NSK-H3M00 SWISS/G KEYBOARD DARFON NSK-H3M06 PORTUGUESE KEYBOARD DARFON NSK-H3M0A ARABIC KEYBOARD DARFON NSK-H3M1A BELGIUM KEYBOARD DARFON NSK-H3M0W SWEDEN KEYBOARD DARFON NSK-H3M0C CZECH KEYBOARD DARFON NSK-H3M0Q HUNGAIAN KEYBOARD DARFON NSK-H3M0N NORWAY
33.A46V1.004 KH.06007.006 KH.06001.002 KH.06004.004 33.A46V1.004 KH.08007.007 KH.08001.012 KB.A2707.001 KB.A2707.002 KB.A2707.003 KB.A2707.004 KB.A2707.007 KB.A2707.008 KB.A2707.009 KB.A2707.010 KB.A2707.011 KB.A2707.012 KB.A2707.013 KB.A2707.014 KB.A2707.015 KB.A2707.016 KB.A2707.017 KB.A2707.018
84
Chapter 6
NS
19.A46V1.001
NS
50.A46V1.006
NS
33.A46V1.008
NS
33.A46V1.007
NS
60.A46V1.009
Chapter 6
85
NS NS NS
HINGE PACK 15.4IN. LEFT/RIGHT WIRELESS ANTENNA LCD 15 IN. TFT XGA LG LP150X08A3 (MADE IN CHINA)
NS NS NS NS NS NS NS NS NS NS NS NS NS Main Board 20
LCD MODULE 15.4IN. WXGA W/ ANTENNA GLARE TYPE INVERTER BOARD DARFON V0.21189301 INVERTER BOARD DELTA DAC08N011 INVERTER BOARD FOXCONN T62I240.00 LCD/INVERTER CABLE 15.4IN. XGA LCD BRACKET 15.4IN. LEFT LCD BRACKET 15.4IN. RIGHT LCD BEZEL 15.4IN. LCD PANEL 15.4IN. W/HINGE HINGE PACK 15.4IN. LEFT/RIGHT WIRELESS ANTENNA LCD 15.4IN. WXGA LG LP154W01A5K2 GLARE TYPE LCD 15.4IN. WXGA CHIMEI N154I1L07 GLARE TYPE MAINBOARD M26P128MB/6IN1/GBL W/O CPU W/PCMCIA SLOT & RTC BATTERY (for Aspire 5020) MAINBOARD M24P64MBSAMSUNG/ 6IN1/GBL W/O CPU W/PCMCIA SLOT & RTC BATTERY (for Aspire 3020) RTC BATTERY
6M.A46V1.021 19.A46V1.001 19.A46V1.002 19.A46V1.003 50.A46V1.005 33.A46V1.006 33.A46V1.005 60.A46V1.008 60.A46V1.005 6K.A46V1.001 25.A46V1.001 LK.15408.010 LK.1540D.004
LB.A4601.001
LB.A4601.002
23.T39V1.001
22.T39V1.001
86
Chapter 6
NS NS NS NS NS NS NS Microphone NS
SDIMM 256M INFINEON HYS64D32020HDL-6-C (.11U/G) SDIMM 256M HYNIX HYMD232M646D6-J SDIMM 256M SAMSUNG M470L3224FT0-CB3 SDIMM 256M MICRON MT8VDDT3264HG-335G3 SDIMM 512M HYNIX HYMD564M646B6-J SDIMM 512M INFINEON HYS64D64020HBDL-6-C SDIMM 512M SAMSUNG M470L6524CU0-CB3 MICROPHONE
23.A46V1.003
Miscellaneous NS NS NS Pointing Device TOUCHPAD BOARD SYNPATICS TM61PUF1G372 56.A46V1.001 LCD SCREW RUBBER LCD SCREW RUBBER LOGO PLATE 47.A46V1.002 47.A46V1.003 31.A46V1.001
Screw NS NS 18 13 NS NS NS 14 NS NS SCW HEX NYL I#R-40/O#4-40 L5.5 SCREW MACH WAFER M2*L4 NI CPU SCREW M2.5*6.5 (2.7KG) CPU SCREW M2.5*6.5 (4.5KG) SCRW WH MS+CBZ M2.5+L4 BLACK SCREW M2.5-6 SCREW M2*3 NYLON 1JMCPC420325 SCREW SCREW M2.5*4L(NYLOCK)BLACK ZN SCREW M2.5X6 34.00015.081 86.T39V1.002 86.00C79.230 86.00C80.230 86.9A323.4R0 86.9A323.6R0 86.9A352.3R0 86.9A352.4R0 86.9A353.4R0 86.9A353.6R0
Chapter 6
87
88
Chapter 6
Chapter 6
89