See Also
Create a New Pipe Run from a P&ID Run (on page 52) Route Pipe across P&ID Off-Page Connectors (on page 52)
Jacketed Piping
This section describes the methods and procedures to model and extract jacketed piping systems. All aspects of jacketed piping can be accomplished using the current version of SmartPlant 3D. There are currently no specific tools to model jacketed piping as one pipeline or to perform the routing of both internal and external piping in a single step. However, there is enough capabilities within the product and in the notation capabilities within the ISOGEN interface which makes it possible to create all the model graphics and necessary drawings to satisfy material requirements and to communicate fabrication and erection requirements through standard SmartPlant 3D drawing output. This method, referred to hereafter as Redundant Modeling, requires that piping materials are placed in the SmartPlant 3D model for both the external and internal portions of the jacket piping system.
Redundant Modeling
Redundant modeling is a method where internal piping (the core) is contained in one pipeline, and the external piping (the jacket) is overlaid on the internal piping in a separate jacket pipeline. This allows for the independent extraction of internal and external piping materials, using ISOGEN, without any problems with overlapping segments. For example, if piping area 01 has the requirement for jacket piping systems, then create an associated pipeline to contain the external piping. Redundant modeling is the best way to handle jacket piping systems when the contractor's scope includes detailed fabrication drawings, isometric drawings, material procurement, and precise configuration depiction.
See Also
Modeling Jacketed Piping (on page 16) Interference Checking (on page 27) Isometric Extraction (on page 27) Orthographic Drawing Production (on page 27)
16
Piping Workflow
See Also
Modeling Jacketed Piping (on page 16) Jacketed Piping (on page 16)
17
Piping Workflow You need to create separate pipelines for the core and jacket for several reasons:
The core and jacket pipelines have different fluid requirements. This is a property on the pipeline object so two pipelines are needed for the two fluid requirements. Creates unique pipeline ID's for isometric drawings to prevent confusion between the core and jacket isometric drawings.
18
19
Piping Workflow c. In the Heat Tracing Requirement box, select Not Heat Traced.
See Also
Modeling Jacketed Piping (on page 16)
20
Piping Workflow To illustrate this concept, core verses jacket modeling, refer to the following figure. A section of a jacket piping system's core piping is shown on the left. The jacket pipe overlaid on top of the internal piping is shown on the right. The configuration was designed to illustrate the most common details of a jacketed piping system. It is not inclusive of all situations nor is it intended to represent a realistic piping configuration. This was the best way to compact many details in a small space for illustration.
Placing all connections and in-line components with the internal core piping reduces the number of disconnected sections, produces better isometric drawings, and minimizes the external modeling requirements. The valves that are used will probably be specific to the jacket piping specification and will have to be defined in the piping commodity specification like any other valve. Generally, this requires dimension tables specific to the valve being purchased, inclusive of the jacket. If a standard valve is being used and a bolt-on jacket is being applied, then the implied item feature of the piping commodity specification should be used to account for that jacket item. Consideration should be given to interference detection when the implied method is being used. Possibly
21
Piping Workflow provide a special dimension table based on a user defined geometric industry standard to allow for the spatial requirements of valve and jacket.
See Also
Modeling Jacketed Piping (on page 16)
When placing jacket pipe to the back of a core flange, there are two placement methods you can use: Point Along or the Edge on solids. The Tools > Point Along placement method works best when starting routing at an end flange or possibly a nozzle. 1. Determine the flange thickness by setting the Locate Filter to Piping Parts, selecting the flange in question, and then reviewing the flange properties . Make a note of this thickness as you will need it in step 6. 2. Click Tools > Point Along.
22
4. Set the reference point to measure from at the end of the core pipe run (at the face of the flange).
5. Start the Route Pipe command. 6. In the Distance box on the Point Along ribbon, enter the thickness of the flange from step 1. 7. Click to indicate that the Point Along distance is your starting point. Note that the beginning of the jacket pipe is aligned with the inside flange face.
8. Route the jacket pipe as usual. The Edge on solids SmartSketch method works well when routing between mated flanges or between mated flanges and an inline component such as a valve. 1. Click Tools > Options. 2. Select the SmartSketch tab. 3. Verify that the Edge on solids option is selected, and then select OK. 4. Start the Route Pipe command.
5. Select the starting location of the jacketed pipe. Make sure that only the Projection 3D SmartSketch glyph appears when you click otherwise you may accidentally connect to the core piping.
23
Piping Workflow 6. Select the ending location of the jacketed pipe. Again, make sure that only the Projection 3D glyph appears.
You may want to use the Tools > Add to SmartSketch List command to restrict the available SmartSketch relationships to just Projection 3D. Another way to model jacket piping is to terminate the jacket prior to the flange or valve with a reducer as shown below. In either case, the details dictated by the jacket system should be followed.
Jump over piping at core pipe flanges is placed in the jacket pipeline as branch points. The heating medium inlet to the jacket and a jump over at a flanged connection are shown below. The jacket and jump over piping are in the jacket pipeline.
24
Piping Workflow Jump over connections at valves can be modeled by terminating the jump over connection in space at the desired locations on the valve. As an alternative, you can use the Place Tap command to tap the valve.
As shown in this figure, the remarks field of the terminator, cap or 'end' may be used to note the connection. Also, use the remarks field of the internal valve to refer to the jump-over connection, thereby completing the cross reference between the two isometrics.
See Also
Modeling Jacketed Piping (on page 16)
25
Piping Workflow
Pipe Supports
Pipe supports serve two purposes in a jacketed system: Locating spacer or restraint details between the internal and external piping. The normal support attachments for the jacket piping, for example: shoes, anchors, dummy legs, and so forth, are placed and extracted with external piping.
Normal Supports
Use the Hangers and Supports task to place supports and hangers on the jacket pipeline just as you would a standard pipeline. Be careful when placing the supports that you only select the jacket pipeline. Otherwise the support will connect to the core pipeline and cause an interference between the support and the jacket pipeline. For more information about placing hangers and support, see the Hangers and Supports Help or the Hangers and Supports User's Guide available from the Help > Printable Guides command.
See Also
Modeling Jacketed Piping (on page 16)
You can place remarks by setting the Locate Filter to Piping Parts, selecting the part that you want to remark, and then selecting Insert > Note. You can also use the Notes tab on the part's property dialog box. In some cases you can use the component number to trigger a special detail on the isometric drawing. For example, if there is more than one way to close the end of a jacket pipe, the end component can carry a component number of CL-1, CL-2, CL-3, and so forth. This in turn can trigger the correct detail for the corresponding closure type to the isometric drawing. 26 Piping User's Guide