Anda di halaman 1dari 48

1-0103-EN

Fittings and Accessories


for Centralized Lubrication Systems and General Use

This brochure provides an overview of metalic pipe unions for fluid engineering.
This brochure is divided into the sections
Solderless pipe unions with tapered sleeve acc. to DIN 3862
SKF Quick Connectors
Solderless pipe unions with cutting sleeve acc. to DIN EN ISO 8434-1 and DIN 2353
Other accessories

Important information on product usage


All products from SKF may be used only for their intended purpose as described in this
brochure and in any instructions. If operating instructions are supplied with the products, they
must be read and followed.
Not all lubricants are suitable for use in centralized lubrication systems. SKF does offer an
inspection service to test customer supplied lubricant to determine if it can be used in a centralized system. SKF lubrication systems or their components are not approved for use with gases,
liquefied gases, pressurized gases in solution and fluids with a vapor pressure exceeding normal
atmospheric pressure (1 013 mbar) by more than 0,5 bar at their maximum permissible
temperature.
Hazardous materials of any kind, especially the materials classified as hazardous by European
Community Directive EC 67/548/EEC, Article 2, Par. 2, may only be used to fill SKF centralized
lubrication systems and components and delivered and/or distributed with the same after
consulting with and receiving written approval from SKF.

Contents

Solderless pipe union with


tapered sleeve acc. to DIN 3862 . . . . . . . . . . . . . . . . . . . . 418
Adaptors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6, 7
Banjo fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17, 18
Bracketed connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Bulkhead connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5, 10
Counterbores . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Cross joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Distributor manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1316
Double tapered sleeves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 9
Elbow connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Flat washers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Form counterbores . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Reducing adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Reinforcing sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Screw plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Socket unions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Tapered sleeves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Tee connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Threaded sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Tube-to-tube-connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Vent plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SKF Quick Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . 1921
Adaptors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Banjo fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Check valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Claw groove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20, 21
Locking pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Tube cutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2944
Banjo fitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Check valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Coupling plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Filler coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Fixing bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Fixing clips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
High pressure hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34, 35
Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Hoses suitable for self-installation . . . . . . . . . . . . . . . . . . . . . . 34
Lock washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Oil level gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Oil reservoirs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42, 43
Plastic tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Pressure gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Quick-disconnect couplings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Relief valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Rotating joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Safety valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40, 41
Shut-off valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Steel tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Topping-up pumps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Tube bending device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

1-0103-EN

Solderless pipe union with


cutting sleeve acc. to DIN EN ISO 8434-1/ DIN 2353 . . . . 2228
Banjo fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Cone plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Connectors for pressure gauges . . . . . . . . . . . . . . . . . . . . . 25, 27
Cutting sleeves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Elbow bulkhead connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Elbow connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Elbow screw-in connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Four-way connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
L-screw-in connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Reducing connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22, 28


Reducing connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Screw plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Straight bulkhead connectors . . . . . . . . . . . . . . . . . . . . . . . 23, 27
Straight connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Straight screw-in fitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Straight screw-in connectors . . . . . . . . . . . . . . . . . . . . . . . 23, 27
Straight screw-in glands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Tee connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25, 27
Tee screw-in connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Union nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Vent plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Solderless pipe union with tapered sleeve acc. to DIN 3862


For pressures up to 45 bar
Counterbores

d10

d8

b3

t3

t4

2.5
4
6
8
10
12

1.5
3
4.5
6.5
8.5
10.5

M60.75
M8 1
M101
M14 1.5
M16 1.5
M18 1.5

4.5
6.5
7
9
9
9.5

5.5
8.5
9
11.5
11.5
12

8.5
12.5
14
18.5
19.5
22

1.3
1.6
1.6
1.6
1.6
1.6

1)

2.5
4
6
8
10
12

c#

1102
1404
1406
1408
1410
1412

d9B11

Q"

f.tube
Specification
of counterbores diam.

c"

(
S'

DIN 3854/DIN 3862 for solderless tube connection

S(

S 

) not shown in DIN standard

Form counterbores
to tap ports for solderless tube connection

2.5
4
6
8
10
12

for counterbore
l

d1

d2

d10

d4

1102
1404
1406
1408
1410
1412

10
10
12
16
18
20

1.5
3
4.5
6.5
8.5
10.5

5
6.5
8.5
12
14
16

4.5
7.5
8
10.5
10.5
11

60.5
65
66
70
72
75

Twist drill
t2
t3
S!

5.5
8.5
9
11.5
11.5
12

902-111
904-411
906-411
908-411
910-411
912-411

tube
diam.

!$

orm counterbore
Order No.

Provision of counterbore
S#

predrill holes

bore hole
to be tapped

c"

c!

S 

counterbore with
form counterbore
up to the stop

Important note #3:


When using a hand drill, take care not to tilt
the counterbore out of the drill axis. To avoid
damages drill steadily without interruption.
Increase pressure slightly at the stop.

1-0103-EN

Form counterbore enlarges bore hole diam. d4 to core hole for ISO thread.

Solderless pipe union with tapered sleeve acc. to DIN 3862


For pressures up to 45 bar
Connectors for steel and copper tubing
Double tapered sleeves DIN 3862
Order No.
402-001 *
404-001
406-001
408-001
410-001
412-001

socket
union
tapped
port

double
tap. sleeve

for tube diam. d

Material

2.5
4
6
8
10
12

brass

Socket unions DIN 3871


Order No

for tube diam.

d1

l1

l2

402-002 *)
404-002
406-002
408-202
410-002
412-002

2.5
4
6
8
10
12

WAF

M6 0.75
M8 1
M10 1
M14 1.5
M16 1.5
M18 1.5

9
12
13
16
17
18

3
4
4
4.5
5.5
6

F05
[!
[

Installation (steel and copper tubing)


1. Push socket union and double tapered
sleeve onto tube end.
2. Insert tube end into tapped port up to
the stop
3. First tighten socket union finger-tight by
hand. Then turn another 11/2 turns.

7
8
10
14
17
19

Material: steel, galvanized surface


*) not shown in DIN standard

Connectors for steel, copper and plastic tubing


Reinforcing sockets (if plastic tubing is used)
Order No.
for tube
d2
d3

l1

402-603
404-603
406-603
406-613
408-603
410-603
412-603

8
10
12
12
15
18
20

1.4
2.2
3.9
3.4
5.4
6.9
8.9

2.3
3.8
5.8
5.8
7.8
9.8
11.8

S"
2.5 0.5
4 0.85
6 1
6 1.25
8 1.25
10 1.5
12 1.5

Material: brass

Tapered sleeves DIN 3862


Order No.
for tube diam. d

tapped port

tapered sleeve
reinforcing
socket

402-611
404-611
406-611
408-611
410-611
412-611

1-0103-EN

402-612
404-612
404-612-MS
406-612
406-612-MS
408-612
408-612-MS
410-612
410-612-MS
412-612

2.5
4
6
8
10
12

Socket unions DIN 3871


Order No.
for tube diam.
Installation (plastic tubing)
1. Insert reinforcing socket into
plastic tube.
2. Push socket union and tapered
sleeve onto tube end.
3. Insert tube end into counterbored
port up to the stop.
4. First tighten socket union finger-tight
by hand. Then turn another 11/2 turns.

Material

*)
*)
*)
*)

2.5
4
4
6
6
8
8
10
10
12

brass

d1

l1

l2

M6 0.75
M81
M8 1
M10 1
M10 1
M14 1.5
M141.5
M161.5
M16 1.5
M18 1.5

9
12
12
13
13
16
16
17
17
18

3
4
4
4
4
4.5
4.5
5.5
5.5
6

WAF
7
8
8
10
10
14
14
17
17
19

F05

[!

socket
union

S!

reinforcing
socket

Material: steel, galvanized surface, *) brass

Solderless pipe union with tapered sleeve acc. to DIN 3862


For pressures up to 45 bar
Adaptors
with cylindrical thread (sealed by flat washer to DIN 7603)

404-004
404-005
404-061
404-063
404-003
404-006
404-040
404-162
404-164
406-158
406-004
406-162
406-054
301-005
406-166
406-055
408-004
408-154
408-160
408-162
301-020
301-001
408-005
408-006
408-022
410-160
410-162
410-163
410-164
410-169
410-004
410-018
410-171
410-022
412-162
412-163
412-164
412-169
412-004
412-014

d1

2.5

M3
M4
M5
M6
M60.75
M81

M81
M81
M5
M8
M81
M101
G 1/8 A
M121
M141.5

M81
M101
M121
G 1/4 A
M141.5
M161.5
G 3/8 A

M101
G 1/8 A
G 1/4 A
M121
G 1/4 A
M141.5
M161.5
M181.5
M221.5

10

M101
M121
G 1/4 A
M141.5
G 1/4 A
M161.5
M181.5
G 1/2 A
M221.5

12

M121
G 1/4 A
M141.5
G 1/4 A
M181.5
M221.5

d2 *)

l1

l2

WAF

M60.75

22
22
22
13
13
15

8.5
8.5
8.5
5.5
5.5
7.5

7
7
7
9
9
11

M81

24
32
20
22
18
18
18
18
18

14
22
5.5
8
7.5
7.5
8
9
9

11
11
11
11
11
14
14
17
17

M101

23
18
19
20
18
19
21

7.5
7.5
9
10
9
9
10

14
14
17
17
17
19
22

M141.5

28
29
30
29
23
26
22
22
24

7.5
8
16
9
10
9
9
10
12

17
17
17
17
17
17
19
22
27

M161.5

30
31
30
29
52
23
24
24
24

7.5
9
10
9
16
9
10
12
12

19
19
19
19
19
19
22
27
27

M181.5

35
35
33
41
24
26

9
10
9
16
10
12

22
22
22
22
22
27

S!

F05

[!

843-130-024
843-130-025
843-130-026
402-004
402-003
402-006

Tube diam.

Order No.

Order No

l1

l2

WAF

301-134

Tube diam.
4

G 1/4

d1

M101

d2

23

7.5

17

301-034

5.5

G 1/4

M141.5

22

17

M101

24
19
20
19
21

8
9
9
9
10

14
17
17
19
22

M141.5

29
28
30
24

7.5
9
10
12

17
17
17
27

267-001.17
406-163
D301-005-MS
406-167
267-001.19

G /8 A
M121
M141.5
M161.5
M181.5

D408-004-MS
D301-001-MS
D301-020-MS
267-001.13

M101
M141.5
G 1/4 A
G 1/2 A

Material: brass

1-0103-EN

Material: steel, galvanized surface

Solderless pipe union with tapered sleeve acc. to DIN 3862


For pressures up to 45 bar
Reducing adapters
with cylindrical thread (sealed by flat washer to DIN 7603)
Order No.

d1

d2

l1

843-130-021 1)
843-130-022 1)
843-130-023 1)

M3
M4
M5

M5
M6
M7

22
22
22

l2
8.5
8.5
8.5

WAF
3
3
3

Material
steel, galvanized surface

406-024
401-016-312

M101
M101

G 1/8
G 1/4

20
26.5

8
7.5

14
17

brass, galvanized surface


brass

22.5
27
40
20

8
8.5
12
9

17
19
27
17

steel, galvanized surface


steel, galvanized surface
steel, galvanized surface
brass

406-044-S1
P-78.01
401-013-161
401-019-352

M101 tap.
M121
G 1/4 A
M141.5

G
G
G
G

401-016-371
243-001.10

M161.5
M161.5

G 1/4
G 1/2

30
31

12
9

19
27

steel, galvanized surface

267-001.47
267-001.60

G 3/8 A
G 3/8 A

G 1/4
G 1/2

31
34

10

22
27

brass

267-001.36
243-001.20

M181.5
M181.5

G 3/8
G 1/2

32

10

22
27

steel, galvanized surface

44-1755-2029

28

/4
/4
/2
1
/8
1

S!

[!

F05

M201.5

G 1/4

12

24

steel, galvanized surface

401-019-132
DZ333
401-013-131
DZ334
267-001.03

G 1/2 A

G
G
G
G
G

/8
1
/4
1
/2
3
/8
3
/4

24
24
40.5
31
40

12

27
27
27
27
36

brass

401-011-132
433-890-131
401-013-171
401-013-111

G
G
G
G

G
G
G
G

1
1 1/4
1
/2
1
/2

49
53
41
29

14
14
16
18

41
55
32
41

/2 A
/2 A
/4 A
1A
1
3

steel, galvanized surface

) With female thread

Adaptors
with tapered thread
Tapered threads are used without washers, as they are self-sealing.
It is not necessary to provide the ports with seal faces.

1-0103-EN

404-662K
404-663K
404-673K
404-047K
404-003K
404-045
404-006K
401-004-512
404-040K
404-040K-US
404-054K
404-072
401-004-903
401-004-904
406-004K
301-105K
456-004K
406-054K
1

2.5

d1 1)
M6 0.75 tap.
M8 1 tap.
M101 tap.
M6 tap.
M6 tap.
M60.75 tap.
M7 tap.
M81 tap.
M81 tap.
M101 tap.
M101 tap.
R 1/8 tap.
1
/8 NPTF
R 1/4 tap.
1
/4-28 UNF
1
/4 BSF
1
/16 BSF
M101 tap.
M121 tap.
R 1/8 tap.
R 1/4 tap.

d2
M6 0.75

M8 1

M10 1

l1

l2

11.5
15
16

4.5
8
7.5

WAF
8
9
12

19
20
20
20
17
62.5
16
25
16
20
14
20
20
18

5
6
6
6
7.4
7.4
7.4
7.4
6
6.7
9
5.6
5
5

11
11
11
11
11
11
11
11
11
11
14
11
11
11

23
18
21
20

7.4
7.4
6
9

14
14
14
17

Material

F05

S!

steel, galvanized surface

402-003K
402-006K
402-008K

Tube diam.

[!

Order No.

) Tapered thread according to DIN 158. short, resp. according to DIN 2999

Solderless pipe union with tapered sleeve acc. to DIN 3862


For pressures up to 45 bar
Bulkhead connectors
with tapered thread (for sealed tube passage through a wall without tube interruption)
Order No.

Tube diam.
4
4
6
8
10

M81 tap.
M101 tap.
M101 tap.
M141.5 tap.
M161.5 tap.

d2

l1

l2

M81
M81
M101
M141.5
M161.5

17
16
18
24
24

7.4
7.4
7.4
11
11

WAF

S!

F05

11
11
14
17
19
[

404-003DK
404-006DK
406-004DK
301-001DK
410-004DK

d1 1)

[!

Material: steel, galvanized surface


1

) Tapered thread according to DIN 158. short

Elbows

[!

F05

S!
S#

with tapered thread

4
4
6
6
6
8

M101 tap.
R 1/8 tap.
M81 tap.
M101 tap.
M121 tap.
M121 tap.

d2)

d3

M81
M81
M101
M101
M101
M141.5

d4

l1

l2

l3

13
13
14
14
14
19.5

21
21
18
18
18
19.5

16
16
18
18
18
24

10
10
10.5
10.5
10.5
10

13
13
12.5
12.5
12.5
14

WAF

14
S
S"

Material: die-cast zinc

502-206K
506-202K
403-006-651

2.5
6
6

M6 tap.
M101 tap.
R 1/4 tap.

d2
M60.75
M101
M101

d3

d4

l1

l2

l3

Material

17
14

8
17
14

10
22
17

9.5
21
17.5

6
11
8.5

steel
brass
steel

S!

d1 1)

Tube diam.

["

Order No.

[!

S#

504-510K
514-018K
506-508K
506-510K
506-512K
508-512K

d1 1)

Tube diam.

["

Order No.

S
S"
"%

brass

) Tapered thread according to DIN 158. short, resp. according to DIN 2999

Elbows

"

406-145K
406-045K
406-089K
406-090K
406-091K
406-092K
406-093K

M81 tap.
M101 tap.
M81 tap.
M101 tap.
R 1/8 tap.
M101 tap.
R 1/8 tap.

M101
M101
M101
M101
G 1/8
M101
M101

7.5
7.5
11
11
11
17
11

21
21
24
24
24
30
24

1
1
2
2
2
2
2

"

[!

Fig.

l2

l1

[!

d1

Order No.

Material: steel, galvanized surface

M6 tap.
M81 tap.
M101 tap.
M6x0.75 tap.

Fig. 1

Fig. 2

1-0103-EN

Material
<'g

504-200K
504-201K
504-202K
504-203K

d1 1)

"$

Tube diam.

&$

Order No.

Solderless pipe union with tapered sleeve acc. to DIN 3862


For pressures up to 45 bar
[!

Elbows

6
8
10
12

6
8
10
12

d2

d3

d4

l1

l2

l3

M101
M141.5
M161.5
M181.5

8
11
15
15

14
18
23
23

30.8
37
42.5
46

21
24.5
26.5
26.5

22
27
29
32

S"
[

Tube diam. d1

DY958
DY960
DY961
DY962

["

Order No.

S!
S#

with tube end (for installation in counterbores as per DIN 3854/DIN 3862)

#

Material: brass

Tube end for tube connection

Screw plugs (sealed by flat washer to DIN 7603)


l3

WAF

14
18
22
26
32
39

17
17
21
26
30
32

8
8
12
14
16
16

3
3
3
4
4
5

11
14
17
19
24
27

9
9.5
12
12
12
14
15

5
5.5
7
7
7
8
10

11
15
15

8
12
12

DIN910-R1-8-5.8
DIN910-R1-48-5.8
DIN910-R3-8-5.8
DIN910-R1-2-5.8
DIN910-R3-4-5.8
DIN910-R1-5.8

G
G
G
G
G
G

/8 A
/4 A
/8 A
1
/2 A
3
/4 A
1 A

402-011
404-011
406-011
408-211
408-011
410-011
412-011

M60.75
M81
M101
M121
M141.5
M161.5
M181.5

1
3

DIN 908-M101-5.8 1) M101


DIN 908-M121-5.8 1) M121
DIN 908-M141-5.8 1) M141
1

14
17
19

9
11
12
17
17
19
22
3
3
3

5
6
6

Material

S!
F05

steel,
galvanized surface
S
F05
steel,
galvanized surface

l2

["

l1

d2

[!

d1

[!

Order No.

S
steel,
galvanized surface
F05

) Hexagon socket

Vent plugs
833-330-016
833-330-021

d1

d2

l1

l2

M101
G 1/8 A

14

17

Material
steel,
galvanized surface

;!

Order No.

S
S!

Flat washers

1-0103-EN

Suitable for thread


mm
inches

9.9
11.4
13.9
15.9
15.9

1
1
1
1.4
2

M6
M8
M10
M12
M12

1
G /8

copper

17.9
17.9
19.9
20.9
21.9
23.9
25.9
26.9
31.9
35.9
38.9

1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2

M14

M16

M18
M20

M22
M27
M30
M33

G 1/4

G 3/8

1
G /2

copper

d1

d2

DIN7603-A610-CU
DIN7603-A811.5-CU
504-019
508-215-CU
508-320-CU

6.2
8.2
10.2
12.2
12.2

DIN7603-A1418-CU
508-108
DIN7603-A1620-CU
DIN7603-A1721-CU
DIN7603-A1822-CU
DIN7603-A2024-CU
DIN7603-A2126-CU
DIN7603-A2227-CU
DIN7603-A2732-CU
DIN7603-A3036-CU
DIN7603-A3339-CU

14.2
13.3
16.2
17.2
18.2
20.2
21.2
22.2
27.3
30.3
33.3

Material

Order No.

S
S!

Solderless pipe union with tapered sleeve acc. to DIN 3862


For pressures up to 45 bar
Threaded sockets
d1
M81
M101
M101
M121
M121
M121
M141.5
M161.5
M161.5
G 1/4 A

WAF

13
15
18
19
17
17
18
19
19
15

Material

3.5
3.5
3.5
5.5
5.5
5.5
5.5
7
7
5.5

05
F

404-203
406-203
406-243-B 1)
408-243-B 1)
458-012
458-012-B 1)
408-023
410-003
410-003-B 1)
408-033-S3

Order No.

steel
[

) Coated with micro-encapsulated adhesive

M101
M121
G 1/4 A

d2
M121
M141.5
G 1/4 A

d3

l1

l2

5
6
7

20
21
31

6
7
10.5

7
7
10.5

WAF

F05

Material

14
17
19

steel,
galvanized
surface

S"
S!

406-103
408-103
853-750-024

d1

Order No.

[!
[

d3

Material

M101

26

brass

406-233

d1

S"

Order No.

Distributor connection

Connectors

404-008
404-009
406-008
406-005
408-008
410-008
412-008

4
4
6
6/8
8
10
12

44-1755-2019 1)

d1

d2

M141.5
M141.5
M141.5
M161.5
M201.5
M201.5
M241.5

M81
M81
M101
M141.5
M141.5
M161.5
M181.5

R1/4

M101

d3
M81
M81
M101
M101
M141.5
M161.5
M181.5

l1

27
38
30
35
40
42
48

19
30
20
23
28
27
33

33

F05

WAF Material
17
17
17
19
24
24
27

steel,
galvanized
surface

S"
S

Tube diam.

S!

Order No.

[
[

24

) Hexagon socket

10

M81
M101
M141.5
M141.5
M161.5
M181.5

M81
M101
M101
M141.5
M161.5
M181.5

d4

l1

10.8
13.8
16.8
16.8
18.8
21.8

27
30
35
40
42
48

13
10
11
14
13
18

[
[

WAF Material
11
14
17
17
19
22

F05
steel,
galvanized
surface

1-0103-EN

4
6
6/8
8
10
12

d3

S"

404-010
406-010
406-805
408-010
410-010
412-010

d2

S#

Tube diam.

S!

Order No.

Solderless pipe union with tapered sleeve acc. to DIN 3862


For pressures up to 45 bar
Elbow connectors

4
4
6

d4

l1

l2

l3

Material

18
18
16.5

12
12
14

33
33
27

16
18
17.5

22
22
15

die-cast zinc
brass
brass

d2

d3

d4

l1

l2

Material

M141.5
M161.5

20
21

20
21

23.5
26

23.5
26

die-cast zinc

M81
M81
M101

S"

< #g $
(

M141.5

d3

S!
S#

d2

504-003
504-103
506-004

d1

["

Order No. Tube diam.

[!

408-013
410-013

8
10

S!
S

"

Tube diam.

Material

die-cast zinc

%#

504-004

<'g

""

Order No.

&

Bracketed connectors

!

Order No. Tube diam.

"

brass

Material

%#

< g

506-010

Tube diam.

!&

Order No.

"

Material

M101
M141.5

15
20

20
25

12
15

aluminum

6
8

DAR506
DAR508

Tube diam.

Order No.

#

%%
!$
(

Tube diam.

d1

d2

Material

M161.5
M141.5

M161.5

steel, galvanized
surface

%%

"
S

10
8 / 10

S!

DAR510
DAR510-S1

Order No.

#"
"

steel, galvanized surface

"

"

!

Material

DAR524

Tube diam.

<'g

Order No.

!

%%

!$
!%

Material

"

"$

steel, galvanized surface

!

"

"

DAR534

Tube diam.

<'g

Order No.

%%

%%
#

Tube-to-tube-connector with air vent

4
6

M81
M101

b
20

h
50

l
40

Material body

"

aluminum

%%

995-001-104
995-001-106

Tube diam.

!


1-0103-EN

Order No.

11

Solderless pipe union with tapered sleeve acc. to DIN 3862


For pressures up to 45 bar
Tee connectors

504-008
506-408
506-008
510-102

Tube diam. d1
4
6/4
6
10

d2

M81
M101
M101
M161.5

M81
M81
M101
M161.5

d3

l1

l2

Material

12
14
14
20

15
18
18
25

30.5
36
36
50

die-cast zinc

Order No.

S"

[!

S!
S"
'

M101
M141.5

die-cast zinc

'

8/6
8

Material

!"

d2

"&

508-602-2
508-002-2

Tube diam.

'$

Order No.

< #g $

S!

%%
#%

!

!!
$

Material

504-045

!#

<'g

Tube diam.

Order No.

"

die-cast zinc
%#
%

M101
M141.5

d2

l1

l2

l3

l4

Material

6
8

40
45

22
25

32
36

37
46

brass
["

6
8

d1

[!

DY964
DY966

Tube diam.

Order No.

[#

S!

M101
M141.5
M161.5
M101
M181.5

h1

l1

l2

6.6
6.6
7
7
6.6

22
32
25
25
42

20
20
20
25
25

9
9
13.5
13.5
9

30
40
40
40
40

9
9
15
15
9

40
50
52
52
60

20
29
29
29
29

Material: aluminum, 1) steel, galvanized surface

M101
M141.5
M161.5
M161.5
M181.5

[!

6
8
10
6
12

d3

DAT506
DAT508
DAT510 1)
DAT510-S5
DAT512

d2

Order No. Tube diam. d1

S"

S!
P

!$

8 (1)
10 (2)

$

DAT510-S1

Material
steel, galvanized surface

< %g $

Tube diam.

Order No.

!$

< #g $

%%

<'

!

1-0103-EN

!$
$

12

Solderless pipe union with tapered sleeve acc. to DIN 3862


For pressures up to 45 bar
Distributor manifold

S!
,

W
#

#"

&#

!'
Q

S"
,

Main tube port


tube diam.
Order No.
4

322-541
323-541

Main tube port


tube diam.
Order No.

321-661
322-661
323-661
324-761
325-861
326-661
328-761
329-761
330-761
331-761
332-761

Main tube port


tube diam.
Order No.

322-861
324-861
326-563
328-861
330-861
332-861
334-861
336-861
338-861
340-861
342-861
344-861

Main tube port


tube diam.
Order No.

322-561
323-561
324-561
325-565
326-562
327-564
328-561
329-561

Main tube port


tube diam.
Order No.

1-0103-EN

321-581
322-581
322-661-S1
323-581
323-661-S1
324-581
325-581
326-581
327-581
328-581
329-581
330-581
330-581-S1
331-581
332-581

Number
of port
2
3

Number
of port
1
2
3
4
5
6
8
9
10
11
12

Number
of port
2
4
6
8
10
12
14
16
18
20
22
24

Number
of port
2
3
4
5
6
7
8
10

Number
of port
1
2
2
3
3
4
5
6
7
8
9
10
10
11
12

d1

d3

l1

h1

M81
M81

2x M81
3x M81

49
62

17
17

10.5
10.5

13
13

13
13

d1

d2

d3

l1

M101
M101
M101
M101
M101
M101
M101
M101
M101
M101
M101

d2

2x
3x
4x
5x
6x
8x
9x
10x
11x
12x

d1
M101
M101
M101
M101
M101
M101
M101
M101
M101
M101
M101
M101

2x
2x
3x
4x
5x
6x
7x
8x
9x
10x
11x
12x

d1
M101
M101
M101
M101
M101
M101
M101
M101

2x
3x
4x
5x
6x
7x
8x
10x

d1
M141.5
M141.5
M141.5
M141.5
M141.5
M141.5
M141.5
M141.5
M141.5
M141.5
M141.5
M141.5
M141.5
M141.5
M141.5

1x
2x
2x
3x
3x
4x
5x
6x
7x
8x
9x
10x
10x
11x
12x

M101
M101
M101
M101
M101
M101
M81
M101
M101
M101
M101

d2 (above)

d3 (below)

M101
M101
M101
M101
M101
M101
M101
M101
M101
M101
M101
M101

M101
M101
M101
M101
M101
M101
M101
M101
M101
M101
M101
M101

2x
2x
3x
4x
5x
6x
7x
8x
9x
10x
11x
12x

d2

d3

M81
M81
M81
M81
M81
M81
M81
M81

d2

d3

M81
M81
M101
M81
M101
M81
M81
M81
M81
M81
M81
M81
M81
M81
M81

41
58
75
92
109
126
160
177
194
211
228

l
41
58
77
92
109
126
143
160
177
194
211
228

34
51
68
52
119
136
153
170

l1

52
34
51
68
85
102
119
136
153
170

h1

20
20
20
20
20
20
20
20
20
20
20

11
11
11
11
11
11
11
11
11
11
11

18
18
18
18
18
18
18
18
18
18
18

17
17
17
17
17
17
17
17
17
17

h1

20
20
17
20
20
20
20
20
20
20
20

11
11
11
11
11
11
11
11
11
11
11

18
18
18
18
18
18
18
18
18
18
18

17
19
17
17
17
17
17
17
17
17

20

11

18

17

l1

h1

52
65
78
91
104
117
130
156

52
39
52
78

17
17
17
17
20
20
17
17

10.5
10.5
10.5
10.5
11
11
10.5
10.5

13
13
13
13
18
18
13
13

13
13
13
13
13
13
13
13

l1

48
61
72
74
94
87
74
113
126
139
152
165
201
178
191

39
52
65
78
91
85
104
117

h1

20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

11
11
11
11
11
11
11
11
11
11
11
11
11
11
11

18
18
18
18
18
18
18
18
18
18
18
18
18
18
18

13
22
13
22
13
13
13
13
13
17
13
17
13
13

Material: aluminum alloy

13

Solderless pipe union with tapered sleeve acc. to DIN 3862


For pressures up to 45 bar
Standard manifolds, configurable *)
Order example

Order code

Product series
Number of ports
01 = 1 port
02 = 2 ports
03 = 3 ports
04 = 4 ports

05 = 5 ports
06 = 6 ports
08 = 8 ports
10 = 10 ports

Design of outlet thread


A = Standard prole, M81 with counterbore for at washer or O-ring
B = Standard prole, M101 with counterbore for at washer or O-ring
C = Standard prole, M141.5 with counterbore for at washer or O-ring
D = Small prole, M81 with surface suitable for sealing with at washer
E = Small prole, M10x1 with surface suitable for sealing with at washer

VL-02AAM3
Product series VL
2 ports
Standard prole made of aluminum
M81 internal thread with counterbore
for at washer or O-ring
M101 main line connection with counterbore for solderless pipe connection
per DIN 3862

Material
A = Aluminum; E = Stainless steel (only for outlet threads A+B)
Design of main line connection
G1 = G1/8 to DIN 3862, Form X, small
G2 = G1/4 to DIN 3862, Form X, small
M1 = M101 to DIN 3862, Form X, small
M2 = M141.5 to DIN 3862, Form X, small
M3 = M101 with counterbore for solderless pipe connection per DIN 3862
M4 = M141.5 with counterbore for solderless pipe connection per DIN 3862
(can only be selected for normal prole)

<'

Distributor manifold

!

<'

!

<'

!

!!

#"

2
0

!'

1)
2)

Dimensions [mm]
A
B
C
E

M101 (M3) 1)

1
2
3
4
5
6
8
10

40
55
70
85
100
115
145
175

20
27.5
27.5
27.5
27.5
27.5
27.5
27.5

15
30
45
60
90
120

20
20
20
20
20
20
20
20

1x15
2x15
3x15
4x15
5x15
7x15
9x15

M101 (M1) 1)
G1/8 (G1)

1
2
3
4
5
6
8
10

34
49
64
79
94
109
139
169

17
24.5
24.5
24.5
24.5
24.5
24.5
24.5

15
30
45
60
90
120

17
17
17
17
17
17
17
17

1x15
2x15
3x15
4x15
5x15
7x15
9x15

Main line
Number of
connection d1 ports

*) See also www.cadenas.com

14

For solderless pipe connection


per DIN 3862
DIN 3852-3 Form W

Dimensions [mm]
A
B
C
E

M141.5 (M4) 1)

1
2
3
4
5
6
8
10

48
63
78
93
108
123
153
183

24
31.5
31.5
31.5
31.5
31.5
31.5
31.5

15
30
45
60
90
120

24
24
24
24
24
24
24
24

1x15
2x15
3x15
4x15
5x15
7x15
9x15

M141.5 (M2) 1)
G1/4 (G2)

1
2
3
4
5
6
8
10

46
61
76
91
106
121
151
181

23
30.5
30.5
30.5
30.5
30.5
30.5
30.5

15
30
45
60
90
120

23
23
23
23
23
23
23
23

1x15
2x15
3x15
4x15
5x15
7x15
9x15

Main line
Number of
connection d1 ports

1-0103-EN

&#

Standard profile A

Solderless pipe union with tapered sleeve acc. to DIN 3862


For pressures up to 45 bar
Distributor manifold

< 

!

< 

!

< 

!

!!
&#
#"

Standard profile B

!'

1)
2)

Dimensions [mm]
A
B
C
E

M101 (M3) 1)

1
2
3
4
5
6
8
10

40
57
74
91
108
125
159
193

20
28.5
28.5
28.5
28.5
28.5
28.5
28.5

17
34
51
68
102
136

20
20
20
20
20
20
20
20

1x17
2x17
3x17
4x17
5x17
7x17
9x17

M101 (M1) 1)
G1/8 (G1)

1
2
3
4
5
6
8
10

34
51
68
85
102
119
153
187

17
25.5
25.5
25.5
25.5
25.5
25.5
25.5

17
34
51
68
102
136

17
17
17
17
17
17
17
17

1x17
2x17
3x17
4x17
5x17
7x17
9x17

Main line
Number of
connection d1 ports

For solderless pipe connection


per DIN 3862
DIN 3852-3 Form X, small

Dimensions [mm]
A
B
C
E

M141.5 (M4) 1)

1
2
3
4
5
6
8
10

52
69
86
103
120
137
171
205

26
34.5
34.5
34.5
34.5
34.5
34.5
34.5

17
34
51
68
102
136

26
26
26
26
26
26
26
26

1x17
2x17
3x17
4x17
5x17
7x17
9x17

M141.5 (M2) 1)
G1/4 (G2)

1
2
3
4
5
6
8
10

46
63
80
97
114
131
165
199

23
31.5
31.5
31.5
31.5
31.5
31.5
31.5

17
34
51
68
102
136

23
23
23
23
23
23
23
23

1x17
2x17
3x17
4x17
5x17
7x17
9x17

Main line
Number of
connection d1 ports

Distributor manifold
Standard profile C
< # $!

!!
&#

< # $!

#"

< # $!

!'

1)
2)

Main line
Number of
connection d1 ports

Dimensions [mm]
A
B
C
E

60
70
94
118
142
166
214
262

1x24
2x24
3x24
4x24
5x24
7x24
9x24

18
35
35
35
35
35
35
35

24

24
48
72
96
144
192

30
23
23
23
23
23
23
23

Main line
Number of
connection d1 ports

M141.5 (M4)

1
2
3
4
5
6
8
10

Dimensions [mm]
A
B
C
E

68
78
102
126
150
174
222
270

1x24
2x24
3x24
4x24
5x24
7x24
9x24

22
39
39
39
39
39
39
39

24

24
48
72
96
144
192

34
27
27
27
27
27
27
27

1-0103-EN

M101 (M3)

1
2
3
4
5
6
8
10

For solderless pipe connection


per DIN 3862
DIN 3852-1 Form X, small

15

Solderless pipe union with tapered sleeve acc. to DIN 3862


For pressures up to 45 bar
Distributor manifold
Small profile D
<'

<'

<'

<'

<'

"

($

!'

M101 (M3)

#"

Main line
Number of Dimensions [mm]
A
B
C
F
connection d1 ports

&

$

!

&#

!

<'

%$

1)
2)

Depth 5.5 mm with surface


suitable for at washers
DIN 3852-3 Form W

1
2
3
4
5
6
8
10

39
52
65
78
91
104
130
156

19.5
26
32.5
39
45.5
26
39
39

52
52
78

1x13
2x13
3x13
4x13
5x13
7x13
9x13

Small profile E
< 

< 

!$

!

!'

5
1)
2)

M101 (M3)

1
2
3
4
5
6
8
10

41
58
75
92
109
126
160
194

20.5
26
37.5
29
29
29
29
29

34
51
68
102
136

1x17
2x17
3x17
4x17
5x17
7x17
9x17

Depth 8 mm
For solderless pipe connection
per DIN 3862

1-0103-EN

#"

Main line
Number of Dimensions [mm]
A
B
C
F
connection d1 ports

'

!

< 

&#

!

< 

16

Solderless pipe union with tapered sleeve acc. to DIN 3862


For pressures up to 45 bar
Cross joints

Q
S

l1

l2

Material

DAK504-S1
DAK506
DAK508
DAK510
DAK512

22
22
32
25
42

20
20
20
20
25

40
40
50
56
60

40
40
50
50
60

20
20
25
28
30

aluminum

%%
P
!

!$

&

M101 / M81
M101
M141.5
M161.5
M181.5

4/6
6
8
10
12

[!

Order No. Tube diam. d1

M161.5

%

steel, galvanized surface

10

Material


DAK510-S1

d1

"!

Order No. Tube diam.

$

Banjo fittings

1-0103-EN

Order No.
504-114
504-115
504-105
405-619-061
506-114
506-342
506-101
586-342
506-013
506-345
506-346
508-342
508-012
508-034
568-342
508-304
508-345
508-346
510-342
510-344
510-343
510-346
510-341

2.5
2.5
2.5
4
4
4
4
4
4
4
6
6
6
6
6
6
8
8
8
8
10
10
10

Tube diam.
4
4
4/6
4/6
6
6
6
6/8
6/8
6 / 10
6 / 10
8
8
8
8/6
8/6
8 / 10
8 / 10
10
10
10
10 / 6
10 / 8

d1
M6
M60.75
M81
M6
M60.75
M8
M81
M81
M101
G 1/8 A
M101
M121
M141.5
M161.5
G 1/8 A
G 1/4 A
M121
M141.5
M161.5
G 1/4 A
M121
M161.5
G 1/4 A

d1
M81
M101
M101
G 1/8 A
M101
M121
M141.5
M121
M141.5
M121
M161.5
M121
M141.5
G 1/4 A
M121
M141.5
M121
M161.5
M121
M161.5
G 1/4 A
M161.5
M121

d2
M60.75
M60.75
M60.75
M81
M81
M81
M81
M81
M81
M81
M101
M101
M101
M101
M101
M101
M141.5
M141.5
M141.5
M141.5
M161.5
M161.5
M161.5

d2
M81
M81
M81
M81
M101
M101
M101
M101
M101
M101
M101
M141.5
M141.5
M141.5
M141.5
M141.5
M141.5
M141.5
M161.5
M161.5
M161.5
M161.5
M161.5

d3
M81
M81
M101
M101
M101
M101
M101
M141.5
M141.5
M161.5
M161.5
M141.5
M141.5
M141.5
M101
M101
M161.5
M161.5
M161.5
M161.5
M161.5
M101
M141.5

l1

l2

l3

20
18
20
20
18
23
20
26
26
27
26
34
34
35
27
35
34
34
35
35
34
35
35

13
13
14
17
17
18
18
18
19
19
21
25
25
30
21
25
27
27
30
27
30
30
30

19
19
21
24
24
25
25
25
27.5
27.5
28.5
35.2
35.2
41
28.5
35.2
37
37
41
37
40
41
40

l4
4.5
5
6.5
4.1
4.5
7.5
7
6.5
6.5
6.8
6.5
7.5
7.5
8.7
7
8.5
7.5
7.5
8.7
8.5
7.5
10.7
7.5

WAF
9
9
11
9
9
11
11
11
14
14
14
17
17
19
14
17
17
17
19
17
17
19
17

l1

l2

l3

l4

WAF

31
31
33
33
33
38
40
44
43
48.5
50
44
43
44
38
40
48.5
50
48.5
50
48.5
50
44

18
19
19
19
21
25
25
25
25
25
30
27
27
27
27
27
27
30
30
30
30
30
30

25.5
27.5
27.5
27.5
28.5
35.2
35.2
35.2
35.2
35
41
37
37
37
37
37
37
41
40
41
40
41
40

6.5
6.5
6.5
6.3
6.3
7.5
7.5
7.5
7.5
7.7
8.7
7.5
7.5
7.5
7.5
7.5
7.7
8.7
7.5
8.7
7.5
8.7
7.5

11
14
14
14
14
17
17
17
17
19
19
17
17
17
17
17
19
19
19
19
19
19
17

Banjo bolt

WAF

Washer
S!

Tube diam.

)
1
)
1
)
1
)
1
)
1
)
1
)

Washer
S

Banjo
union

[!
["

) Miniature design

S"
F05
Washer

Banjo bolt

S!

L-type

[#

502-161
502-101
502-102
504-161
504-162
504-411
504-401
504-101
504-102
504-108
506-140
506-142
506-012
506-145
506-108
506-214
508-142
508-144
508-145
508-024
510-142
510-145
510-024

[#

Order No.

Elbow

Banjo union

Washer
S
[!
["

17

Solderless pipe union with tapered sleeve acc. to DIN 3862


For pressures up to 45 bar
Banjo fittings
l1

l2

504-109
504-112
506-242
506-025
508-242
508-013
508-025
510-242

M81
M101
M121
M141.5
M121
M141.5
G 1/4 A
M121

M81
M81
M101
M101
M141.5
M141.5
M141.5
M161.5

26
26
34
34
34
34
35
34

38
38
48
48
54
54
54
60

4
4
6
6
8
8
8
10

l3
6.5
6.5
7.5
7.5
7.5
7.5
7.5
7.5

Double
banjo union

WAF
11
14
17
17
17
17
17
17

Banjo bolt
F05
Washer
S!

d2

S!

d1

Order No. Tube diam.

["

Tee

S
[!

d3

l1

l2

l3

WAF

504-110
504-111
504-106
506-442
506-014
586-442
506-026
508-442
508-014
568-442
508-305
510-442

M81
M101
M101
M121
M141.5
M121
M141.5
M121
M141.5
M121
M141.5
M121

M81
M81
M81
M101
M101
M101
M101
M141.5
M141.5
M141.5
M141.5
M161.5

M81
M81
M101
M101
M101
M141.5
M141.5
M141.5
M141.5
M101
M101
M161.5

31
31
33
38
40
44
43
44
43
38
40
48.5

38
38
38
48
48
48
48
54
54
54
54
60

6.5
6.5
6.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5

11
14
14
17
17
17
17
17
17
17
17
19

8
8

6
6

S"
F05

Banjo bolt
Washer

Washer
S
[!

Double banjo union

1-0103-EN

4
4
4/
6
6
6/
6/
8
8
8/
8/
10

S!

d2

d1

S!

Order No. Tube diam.

["

Cross

Washer

18

SKF Quick Connectors


For pressures up to 300 bar (metal tube with claw groove)
Tools for the preparation of claw grooves on the ends of steel tubes
Tube cutter

for tube diam.

Tube cutter
Order No.

Cutting wheel
Order No.

4
6
8

169-000-336
169-000-337
169-000-338

844-330-006
844-330-007
844-330-007

3.1
4.9
6.9

0.2

5.0
6.2
6.2

0.3 0.7
0.4 0.9
0.5 0.9

cdQT

4
6
8

+0.3

for tube diam.

Claw groove

Adaptors
with cylindrical thread
Tube diam. A G

4
4
4
4

M81
M101
M101
G 1/8

6
6
6
6

8.8
8.8
8.8
8.8

11.5
13.5
13.5
13.5

23.8
23.8
23.8
23.8

WAF1
10
12
12
12

WAF2
2.5
2.5
2.5
2.5

Seal
NBR
NBR
FKM (FPM)
NBR

406-158-VS
406-004-VS
406-004-S8-VS
456-004-VS
406-054-VS
406-162-VS
406-162-S8-VS

6
6
6
6
6
6
6

M81
M101
M101
G 1/8
G 1/4
M121
M121

6
6
6
6
7
7
7

11.7
11.7
11.7
11.7
11.7
11.7
11.7

13.2
13.5
13.5
13.5
16.4
15.4
15.4

30.5
27
27
27
28
28
28

12
12
12
12
12
14
14

3
4
4
4
4
4
4

NBR
NBR
FKM (FPM)
NBR
NBR
NBR
FKM (FPM)

408-004-VS
408-004-S8-VS
408-162-VS
408-162-S8-VS

8
8
8
8

M101
M101
M121
M121

6
6
7
7

13.9
13.9
13.9
13.9

15.2
15.2
15.2
15.2

32.3
32.3
32.8
32.8

14
14
14
14

5
5
6
6

NBR
FKM (FPM)
NBR
FKM (FPM)

F05!

404-003-VS
404-006-VS
404-006-S8-VS
404-040-VS

2
1
0

Order No.

F05

with tapered thread

1-0103-EN

Tube diam. A G

WAF1

WAF2

4
4
4
4
4

M6 tap.
M81 tap.
M101 tap.
1/4-28 SAE LT
1
/8 NPTF

5.5
5.5
5.5
5.1
8

8.8
8.8
8.8
8.8
8.8

11.5
11.5
11.5
11.5
11.5

25.8
23.3
22.8
26.3
24.8

10
10
10
10
10

2.5
2.5
2.5
2.5
2.5

451-006-468-VS
451-006-498-VS
451-006-518-VS
406-423W-VS

6
6
6
6

M6 tap.
M81 tap.
M101 tap.
R 1/8 tap.

5.5
5.5
5.5
6.5

11.7
11.7
11.7
11.7

13.5
13.5
13.5
13.5

30
29.5
27
28.5

12
12
12
12

2.5
4
4
4

F05

F05!

451-004-462-VS
451-004-498-VS
451-004-518-VS
404-673K-V1-VS
404-040K-V1-VS

2
1
0

Order No.

19

SKF Quick Connectors


For pressures up to 300 bar (metal tube with claw groove)
Elbows, pivoted
with cylindrical thread
B

l1

l2

WAF1 WAF2

Seal

504-101-VS
504-102-VS
504-108-VS

4
4
4

M81
M101
G 1/8

6
6
6

10
10
10

21.8
21.8
21.8

20.5
20.5
20.5

10
12
12

9
9
9

506-139-VS
506-140-VS
506-140-S8-VS
506-108-VS
506-142-VS
506-142-S8-VS

6
6
6
6
6
6

M81
M101
M101
G 1/8
M121
M121

6
6
6
6
7
7

12.5
12.5
12.5
12.5
12.5
12.5

26
26
26
26
26
26

21
21
21
21
23
23

10
12
12
12
14
14

10
10
10
10
10
10

NBR
NBR
FKM (FPM)
NBR
NBR
FKM (FPM)

508-142-VS
508-142-S8-VS

8
8

M121
M121

7
7

14.5
14.5

28.8
28.8

23
23

14
14

12
12

NBR
FKM (FPM)

l1

l2

F05!

NBR
NBR
NBR

F05
[!

Tube diam. A

Order No.

with tapered thread


[

Seal

455-546-048-VS
455-546-048-S8-VS
455-529-048-VS
455-529-048-S8-VS
455-531-048-VS
455-531-048-S8-VS
455-569-048-VS

4
4
4
4
4
4
4

M6 tap.
M6 tap.
M81 tap.
M81 tap.
M101 tap.
M101 tap.
R 1/8 tap.

6
6
6
6
6
6
7.5

10
10
10
10
10
10
10

21.8
21.8
21.8
21.8
21.8
21.8
21.8

20
20
20
20
20
20
20.5

10
10
10
10
12
12
12

9
9
9
9
9
9
9

NBR
FKM (FPM)
NBR
FKM (FPM)
NBR
FKM (FPM)
NBR

455-529-068-VS
455-529-068-S8-VS
455-531-068-VS
455-531-068-S8-VS
455-565-068-VS

6
6
6
6
6

M81 tap.
M81 tap.
M101 tap.
M101 tap.
R 1/4 tap.

6
6
6
6
11

12.5
12.5
12.5
12.5
12.5

26
26
26
26
26

20
20
20.5
20.5
24.5

10
10
12
12
14

10
10
10
10
10

NBR
FKM (FPM)
NBR
FKM (FPM)
NBR

F05!
0
1

WAF1 WAF2

F05

Tube diam. A

[!

Order No.

Banjo fittings

l1

l2

WAF1

4
4
4

M5
M8
M101

5
7
7

8.8
8.8
8.8

21.8
23.8
24.8

18
20
22.5

8
12
14

Seal
NBR
NBR
NBR

445-519-041-VS

G1/8

8.8

24.8

22.5

14

NBR

F05

0
1

Tube diam. A G

504-401-S1-VS
504-411-VS
504-103-VS

[!

Order No.

1-0103-EN

20

SKF Quick Connectors


For pressures up to 300 bar (metal tube with claw groove)
Elbows with tapered thread
B

l1

l2

WAF

Seal

4
4
4
4
4
4
4
4
4
4

M6 tap.
M6 tap.
M81 tap.
M81 tap.
M101 tap.
M101 tap.
R 1/8 tap.
R 1/8 tap.
1
/4-28 SAE LT
1
/8 NPTF

6
6
6
6
6
6
7.5
7.5
5.1
7

10
10
10
10
10
10
10
10
10
10

21.8
21.8
21.8
21.8
21.8
21.8
21.8
21.8
21.8
21.8

14
14
13.5
13.5
13.5
13.5
15
15
15.5
15

9
9
9
9
9
9
9
9
9
9

NBR
FPM
NBR
FPM
NBR
FPM
NBR
FPM
NBR
NBR

453-006-468-VS
453-006-468-S8-VS
506-508-VS
506-508-S8-VS
506-510-VS
506-510-S8-VS
506-511-VS
506-511-S8-VS
506-512-VS
453-006-651-VS

6
6
6
6
6
6
6
6
6
6

M6 tap.
M6 tap.
M81 tap.
M81 tap.
M101 tap.
M101 tap.
R 1/8 tap.
R 1/8 tap.
M121 tap.
R 1/4 tap.

6
6
6.5
6.5
6
6
8.5
8.5
7
11.5

12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5

26
26
26
26
26
26
26
26
26
26

15
15
14
14
14
14
16.5
16.5
15
19.5

10
10
10
10
10
10
10
10
10
10

NBR
FPM
NBR
FPM
NBR
FPM
NBR
FPM
NBR
NBR

[
F05

0
1

Tube diam. A G

[!

453-004-471-VS
453-004-471-S8-VS
504-201-VS
504-201-S8-VS
504-202-VS
504-202-S8-VS
514-018-VS
514-018-S8-VS
504-200K-V1-VS
514-018K-V1-VS

Order No.

VPKM-RV-VS
VPKG-RV-VS

6
6

Opening pressure [bar]

3 +2
3 +2

M101 tap.
R 1/8 tap.

Tube diam.

"$

Order No.

CdQT%

Check valve

'

F05 !
m""$

406-426-VS

Tube diam.

Order No.

CdQT%

Connector

##$

Locking pin
l1

l2

6
8

31
37

21
25

[!

4
6

d1

1-0103-EN

450-204-002
450-206-002

Tube diam. d

Order No.

21

Solderless pipe union with cutting-sleeve


acc. to DIN EN ISO 8434-1 and DIN 2353

D
(tube diam.)

Pressure
[bar]

4
6
8
10
12

6
7
7
7
7.5

100

406-301
408-301
410-301

6
8
10

9.5
9.5
10

500

412-301
415-301
418-301

12
15
18

10
10
10

400

404-301 1)
406-331 1)
96-5708-0058 1)
96-5710-0058 1)
96-5712-0058 1)

Order No.

Straight connectors (tube to tube)


S

Cutting sleeves to DIN 3861 / ISO 8434-1

Material: steel, galvanized


surface (Cr-6 free)

Order No.
404-404 1)
406-406
408-408
410-410
412-412
415-415
418-418

Tube diam.
d. d1
4
6
8
10
12
15
18

Reducing connectors
Tube diam. Tube diam.
Order No .
d
d1
504-410
504-412
506-410
506-412
508-410
506-413
508-412
510-410
508-413
510-412
512-410
510-413
512-412
515-410

Union nuts to DIN 3870/ISO 8434-1

6
8
8
10
10
12
12
12
15
15
15
18
18
18

4
4
6
6
8
6
8
10
8
10
12
10
12
15

Material: steel,
galvanized surface
(Cr-6 free)

F05

Reducing connectors

404-302 1)
406-332 1)
96-5608-0058 1)
96-5610-0058 1)
406-302

d1

4
6
8
10
6

M81
M101
M121
M141
M121.5

WAF

11
11.5
12
12.5
14.5

10
14
14
17
14

408-302
410-302

8
10

M141.5
M161.5

14.5
15.5

17
19

412-302
96-2815-0058
96-2818-0058

12
15
18

M181.5
M221.5
M261.5

15.5
17
18

22
27
32

Pressure
[bar]

D
(tube diam.)

Order No.

100

Order No.
500

400

Straight screw-in glands


with short threaded end for screwing into thread

408-406
410-406
443-706-121
443-706-151
443-706-181
410-408
443-708-121
443-708-151
443-708-181
443-710-061
412-410
415-410
443-710-181
443-712-151
418-412
422-412
443-715-181

Tube diam. d
6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
12
15

d1
8
10
12
15
18
10
12
15
18
8
12
15
18
15
18
22
18

Order No.
406-323
408-313
410-313
410-323

Tube diam. d
6
8
10
10

d1
M101 tap.
M141.5
M161.5
M141.5

d2

M101
M141.5
M161.5
M161.5

9
9
9

The cutting sleeve screw unions shown correspond to the L-series (light version).
1
) LL-series (extra light version)

22

1-0103-EN

S!

Solderless pipe union with cutting-sleeve


acc. to DIN EN ISO 8434-1 and DIN 2353
Straight screw-in connectors
to DIN 2353

Straight screw-in connectors


to DIN 2353

with metrical thread

with Whitworth pipe thread

M121.5
M141.5
M141.5
M161.5
M181.5
M181.5
M201.5
M221.5
M271.5

24-2105-2373
96-6002-0058
404-413
404-403
406-423
406-443
406-433
406-423
441-008-511
24-2105-2381

2.5
4
4
4
6
6
6
6
8
10

M6 tap.
M61 tap.
M81 tap.
M101 tap.
M101 tap.
M6 tap.
LL
M81 tap.
M101 tap.
M101 tap.
M101 tap.

410-443

10

M101 tap.

L-screw-in connectors
directionally adjustable
Order No. Tube diam. d

d1

4
6
6
6
8
8
8
8
10
10
10
12
12
12
15
15
15
18
18
22
22
28
28

G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G

96-1106-0058
96-1108-0058
96-1109-0058
96-1111-0058
96-1110-0058
96-1112-0058
96-1113-0058
96-1114-0058
96-1117-0058
96-1116-0058
96-1121-0058
96-1120-0058

6
8
8
10
10
12
12
14
16
16
20
20

G
G
G
G
G
G
G
G
G
G
G
G

404-403W
406-423W
408-423W
96-5909-0058
96-5911-0058
24-2105-2382
96-5912-0058
96-5913-0058

4
6
8
8
10
10
11
12

R
R
R
R
G
G
G
G

Series

/4 A
1
/8 A
1
/4 A
3
/8 A
1
/8 A
1
/4 A
3
/8 A
1
/2 A
1
/4 A
3
/8 A
1
/2 A
1
/4 A
3
/8 A
1
/2 A
3
/4 A
1
/2 A
3
/8 A
1
/2 A
3
/4 A
1
/2 A
3
/4 A
3
/4 A
1A

/4 A
/4 A
/8 A
1
/4 A
3
/8 A
3
/8 A
1
/2 A
1
/2 A
3
/8 A
1
/2 A
1
/2 A
3
/4 A
1
3

/8
/8
/8
1
/4
1
/4
1
/8
1
/8
3
/8
1
1

tap.
tap.
tap.
tap.
tap.
tap.
tap.
tap.

LL

Series
S

443-406-061
443-408-081
443-410-101
443-412-121
443-415-151
443-418-181

6
8
10
12
15
18

M121.5
M141.5
M161.5
M181.5
M221.5
M261.5

443-406-351
443-408-083
96-3010-0060
96-3012-0060
96-3014-0060
96-3016-0060

6
8
10
12
14
16

M141.5
M161.5
M181.5
M201.5
M221.5
M241.5

443-410-211

10

G 3/8 A

443-406-691
443-410-161

6
10

G 1/8 A
G 1/4 A

Straight bulkhead connectors

S
1-0103-EN

d1

44-2573-6330
406-403W
96-0204-0058
406-463W
96-0203-0058
408-403W
408-413W
408-453W
410-403W
410-413W
410-433W
412-423W
412-403W
412-453W
415-443W
415-403W
415-433W
418-403W
418-413W
96-0223-0058
96-0222-0058
428-413W
96-0228-0058

6
6
8
10
12
12
14
16
20

Order No. Tube diam. d

96-1206-0058
406-413
408-413
410-413
412-453
96-1212-0058
96-1214-0058
96-1216-0058
96-1220-0058

Series

<PgfP[[cWXRZ]Tbb

M101
M121
M141.5
M181.5
M141.5
M161.5
M181.5
M181.5
M221.5
M221.5
M181.5
M221.5
M261.5
M332
M422
M482

6
8
10
10
12
12
12
15
15
18
18
22
22
28
35
42

d1

406-403
96-0308-0058
410-403
410-463
412-423
412-403
412-433
415-403
415-413
418-403
96-0319-0058
96-0321-0058
96-0322-0058
96-0328-0058
96-0335-0058
96-0342-0058

Order No. Tube diam. d

Order No. Tube diam. d

d1

406-416
408-416
410-416
412-416
415-416
418-416
422-416

12.5
14.5
16.5
18.5
22.5
26.5
30.5

6
8
10
12
15
18
22

LL-series (extra light version)


L-series (light version)
S-series (heavy duty version)

23

Solderless pipe union with cutting-sleeve


acc. to DIN EN ISO 8434-1 and DIN 2353

Order No. Tube diam. d

d1

Order No. Tube diam. d d1

406-409
408-409
410-409
412-409
415-409
418-409
443-190-901

12.5
14.5
16.5
18.5
22.5
26.5
30.5

445-529-041

445-531-061
96-7808-0058
445-535-101
96-7812-0058
96-7815-0058
96-7818-0058
96-7822-0058

6
8
10
12
15
18
22

Elbow connectors
Order No.

Tube diam. d

406-404
96-0408-0058
410-404
412-404
443-215-001
443-218-001
443-290-001

6
8
10
12
15
18
22

Elbow screw-in connectors


Tube diam. d

96-6202-0058
96-6204-0058
404-425
406-445
406-435
406-425
408-425

24

4
4
4
6
6
6
8

d1
M6 tap.
M81 tap.
M101 tap.
M6 tap.
M81 tap.
M101 tap.
M101 tap.

Series

Order No.

LL

406-405
408-405
410-405
412-405
415-405

6
8
10
12
15

M101 tap.
M121.5 tap.
M141.5 tap. L
M161.5 tap.
M181.5 tap.

410-425

10

M161.5 tap. S

404-405W
96-6106-0058
96-6108-0058
96-6110-0058
96-6112-0058

4
6
8
10
12

R
R
R
R
R

/8
/8
/8
1
/4
1
/4

tap.
tap.
tap.
tap.
tap.

LL

406-405W
406-515W
408-425W
408-405W
410-405W
412-405W
415-405W
418-405W

6
6
8
8
10
12
15
18

R
R
R
R
R
R
R
R

/8
/4
1
/8
1
/4
1
/4
3
/8
1
/2
1
/2

tap.
tap.
tap.
tap.
tap.
tap.
tap.
tap.

96-1406-0058
96-1408-0058
96-1410-0058
96-1412-0058
96-1414-0058
96-1416-0058

6
8
10
12
14
16

R
R
R
R
R
R

tap.
tap.
tap.
tap.
tap.
tap.

1
1

/4
/4
/8
3
/8
1
/2
1
/2
1
3

LL-series (extra light version)


L-series (light version)
S-series (heavy duty version)

Series

M81

LL

6
8
10
12
15
18
22

M101
M121.5
M141.5
M161.5
M181.5
M221.5
M261.5

96-8006-0058
96-8008-0058
96-8010-0058
96-8012-0058
96-8014-0058
96-8016-0058
96-8020-0058

6
8
10
12
14
16
20

M121.5
M141.5
M161.5
M181.5
M201.5
M221.5
M271.5

96-7106-0058
96-7108-0058

6
8

M101
M101

LL

96-7004-0058

G 1/8 A

LL

445-519-041
445-519-061
445-516-061
445-516-081
445-516-101
445-521-122
445-513-181
445-517-222

4
6
6
8
10
12
18
22

G
G
G
G
G
G
G
G

96-7906-0058
96-7908-0058
96-7910-0058
96-7912-0058
96-7914-0058
96-7916-0058
96-7920-0058

6
8
10
12
14
16
20

G
G
G
G
G
G
G

96-7006-0058
96-7008-0058

6
8

/8 A
/8 A
/4 A
1
/4 A
1
/4 A
3
/8 A
1
/2 A
3
/4 A
1
1

/4 A
/4 A
3
/8 A
3
/8 A
1
/2 A
1
/2 A
3
/4 A

G 1/8 A
G 1/8 A

LL

1-0103-EN

Banjo fittings

Max. wall thickness

Elbow bulkhead connectors

Solderless pipe union with cutting-sleeve


acc. to DIN EN ISO 8434-1 and DIN 2353

6 #

Order No. Tube diam. d

6 #

< %g $

%

d1

Series

96-6404-0058
96-6406-0058
96-6408-0058

4
6
8

M81 tap.
M101 tap. LL
M101 tap.

96-0906-0058
96-0908-0058
445-910-551
96-0912-0058
96-0915-0058

6
8
10
12
15

M101 tap.
M121.5 tap.
M141.5 tap. L
M161.5 tap.
M181.5 tap.

96-1806-0058
96-1808-0058
96-1810-0058
96-1812-0058
96-1814-0058
96-1816-0058

6
8
10
12
14
16

M121.5
M141.5
M161.5
M181.5
M201.5
M221.5

tap.
tap.
tap. S
tap.
tap.
tap.

96-6304-0058
96-6306-0058
96-6308-0058

4
6
8

R 1/8 tap.
R 1/8 tap.
R 1/8 tap.

LL

96-0806-0058
96-0808-0058
96-0810-0058
96-0812-0058
96-0815-0058
96-0818-0058

6
8
10
12
15
18

R
R
R
R
R
R

/8
/4
1
/4
3
/8
1
/2
1
/2

tap.
tap.
tap.
tap.
tap.
tap.

96-1706-0058
96-1708-0058
96-1710-0058
96-1712-0058
96-1714-0058
96-1716-0058

6
8
10
12
14
16

R
R
R
R
R
R

tap.
tap.
tap.
tap.
tap.
tap.

445-721-121
445-713-151
445-717-221

12
15
22

G 3/8 A
G 1/2 A
G 3/4 A

445-735-101
445-739-151

10
15

M141.5
M181.5

U^acdQT 

L = light version

Tube d Order No.


4
6
6
6
8
8
10
10
12
12

6 #

Tee screw-in connectors

Connectors for pressure gauges

96-8804-0058
406-411
248-610.01
441-106-162
408-411
441-108-162
410-411
441-110-163
412-411
441-112-162

S = heavy duty version

Version
C
A
B
C
A
C
A
C
A
C

Tube d Order No.


6
6
8
8
10
10
12
12

96-0406-0060
96-8906-0058
96-0408-0060
96-8908-0058
96-0410-0060
96-8910-0058
96-0412-0060
96-8912-0058

Version
A
C
A
C
A
C
A
C

Four-way connectors
Order No.

Tube diam. d

96-2106-0058
446-308-001
446-310-001
446-312-001
446-315-001
96-2118-0058
96-2122-0058

6
8
10
12
15
18
22

/4
/4
/8
3
/8
1
/2
1
/2
1
3

Tee screw-in connectors

directionally adjustable
Order No. Tube diam. d

Order No.

1-0103-EN

96-6904-0058 1)
406-407
408-407
410-407
412-407
415-407
418-407
422-407

Tube diam. d
4
6
8
10
12
15
18
22

Series

6
8
10
12
15
18
22

M121.5
M141.5
M161.5
M181.5
M221.5
M261.5
M301.5

445-806-351
96-3208-0060
96-3210-0060
96-3212-0060
96-3214-0060
96-3216-0060
96-3220-0060

6
8
10
12
14
16
20

M141.5
M161.5
M181.5
M201.5
M221.5
M241.5
M301.5

Tee connectors

d1

96-3106-0060
444-808-351
445-810-371
96-3112-0060
96-3115-0060
96-3118-0060
96-3122-0060

LL-series (extra light version)


L-series (light version)
S-series (heavy duty version)

25

Solderless pipe union with cutting-sleeve


acc. to DIN EN ISO 8434-1 and DIN 2353
Reducing connections

Reducing connections

8
10
10
12
12
12
15
15
15
15
18
18
18
18
18
22
22
22
22
22
22

96-1610-0060
96-1611-0060
96-1612-0060
96-1621-0060
96-1622-0060
96-1623-0060
96-1631-0060
96-1632-0060
96-1633-0060
96-1634-0060
96-1641-0060
96-1642-0060
96-1643-0060
96-1644-0060
96-1645-0060
96-1651-0060
96-1652-0060
96-1653-0060
96-1654-0060
96-1655-0060
96-1656-0060

8
10
10
12
12
12
14
14
14
14
16
16
16
16
16
20
20
20
20
20
20

LL-series (extra light version)


L-series (light version)
S-series (heavy duty version)

26

Series
LL

6
6
8
6
8
10
6
8
10
12
6
8
10
12
15
6
8
10
12
15
18

M141.5
M161.5
M161.5
M181.5
M181.5
M181.5
M221.5
M221.5
M221.5
M221.5
M261.5
M261.5
M261.5
M261.5
M261.5
M302
M302
M302
M302
M302
M302

6
6
8
6
8
10
6
8
10
12
6
8
10
12
14
6
8
10
12
14
16

M161.5
M181.5
M181.5
M201.5
M201.5
M201.5
M221.5
M221.5
M221.5
M221.5
M241.5
M241.5
M241.5
M241.5
M241.5
M302
M302
M302
M302
M302
M302

G 1/8 A
G 1/8 A
G 1/4 A
G 1/4 A
G 1/4 A
G 1/4 A
G 3/8 A
G 3/8 A
G 3/8 A
G 3/8 A
G 1/2 A
G 1/2 A
G 1/2 A
G 1/2 A
G 1/2 A
G 1/2 A
G 3/4 A
G 3/4 A
G 3/4 A
G 3/4 A
G 3/4 A
G 3/4 A
G1A
G 1A
G1A
G1A
G1A
G1A
G 1 1/4 A
G 1 1/4 A
G 1 1/4 A
G 1 1/4 A
G 1 1/2 A
G 1 1/2 A
G 1 1/2 A
G 1 1/2 A
G2A

G 1/4
G 3/8
G 1/8
G 3/8 A
G 1/2
G 3/4
G 1/8
G 1/4
G 1/2
G 3/4
G 1/8
G 1/4
G 3/8
G 3/4
G1
G 1 1/4
G 1/4
G 3/8
G 1/2
G1
G 1 1/4
G 1 1/2
G 1/4
G 3/8
G 1/2
G 3/4
G 1 1/4
G 1 1/2
G 1/2
G 3/4
G1
G 1 1/2
G 1/2
G 3/4
G1
G 1 1/4
G 1 1/2

31
32
28
36
40
43
22.5
36
41
44
24
24
36
46
49
53
26
26
41
51
55
57
29
29
29
47
57
59
32
32
52
60
36
36
36
58
62

Straight screw-in fitting


Order No.

Tube diam.
d1
d3

Series

96-0506-0060
96-0508-0060
96-0510-0060
96-0512-0060
96-0515-0060
96-0518-0060
96-0522-0060

6
8
10
12
15
18
22

M101
M121.5
M141.5
M161.5
M181.5
M221.5
M261.5

96-0606-0060
96-0608-0060
96-0610-0060
96-0612-0060
96-0614-0060
96-0616-0060
96-0620-0060

6
8
10
12
14
16
20

M121.5
M141.5
M161.5
M181.5
M201.5
M221.5
M272

96-0706-0060
96-0708-0060
96-0709-0060
96-0710-0060
96-0711-0060
96-0712-0060
96-0713-0060
96-0715-0060
96-0718-0060
96-0722-0060

6
8
8
10
10
12
12
15
18
22

G 1/8 A
G 1/4 A
G 3/8 A
G 1/4 A
G 3/8 A
G 3/8 A
G 1/2 A
G 1/2 A
G 1/2 A
G 3/4 A

L
1-0103-EN

96-1508-0060
96-1511-0060
96-1512-0060
96-1521-0060
96-1522-0060
96-1523-0060
96-1531-0060
96-1532-0060
96-1533-0060
96-1534-0060
96-1541-0060
96-1542-0060
96-1543-0060
96-1544-0060
96-1545-0060
96-1551-0060
96-1552-0060
96-1553-0060
96-1554-0060
96-1555-0060
96-1556-0060

d3
M101
M121
M121

96-3114-0058
96-3115-0058
96-3116-0058
96-3117-0058
96-3118-0058
96-3119-0058
96-3101-0058
96-3120-0058
96-3121-0058
96-3122-0058
96-3102-0058
96-3103-0058
96-3123-0058
96-3124-0058
96-3125-0058
96-3126-0058
96-3104-0058
96-3105-0058
96-3127-0058
96-3128-0058
96-3129-0058
96-3130-0058
96-3106-0058
96-3107-0058
96-3108-0058
96-3131-0058
96-3132-0058
96-3133-0058
96-3109-0058
96-3110-0058
96-3134-0058
96-3135-0058
96-3111-0058
96-3112-0058
96-3113-0058
96-3136-0058
96-3137-0058

S!

4
4
6

Tube diam.
d2
l1

6
8
8

d1

Tube diam. d1 Tube diam. d2

96-1406-0060
96-1408-0060
96-1410-0060

Order No.

S"

Order No.

S!

S"
S

Sealing by sealing edge

Solderless pipe union with cutting-sleeve


acc. to DIN EN ISO 8434-1 and DIN 2353
Straight connectors (tube to tube)

with Eolastic washer and EO2 function nut

with EO2 function nut

Straight screw-in connectors

Order No.
EOLASTIC washer

Tube diam. d
1

471-004-191 )
471-004-311 1)

d1
G 1/8 A
M101

471-006-192
471-006-161
471-006-311
471-006-351

G 1/8 A
G 1/4 A
M101
M141.5

471-008-161
471-008-211
471-008-351
471-008-391

10

G 1/4 A
G 3/8 A
M101
M141.5
M181.5

471-012-161
471-012-211
471-012-391

12

G 1/4 A
G 3/8 A
M181.5

471-015-131

15

G 1/2 A

471-010-161
471-010-211
471-010-312
471-010-351
471-010-391

Tee connectors
with EO2 function nut

G 1/4 A
G 3/8 A
M141.5
M181.5

6
8
10
12
15
18

Order No.

474-506-061
474-508-081
474-510-101
474-512-121
474-515-151
474-518-181

Tube diam. d, d1

Order No.

476-006-001
476-008-001
476-010-001
476-012-001
476-015-001

Tube diam. d
6
8
10
12
15

) LL-series (extra light version)

Straight bulkhead connectors

Connectors for pressure gauges

with EO2 function nut

with EO2 function nut

6 #

\Pg %
Order No.

Tube diam. d

1-0103-EN

474-606-331
474-608-351
474-610-351
474-612-391
474-615-431
474-618-441

6
8
10
12
15
18

d1
12.5
14.5
16.5
18.5
22.5
26.5

< %g $
U^acdQT 

Order No.
441-106-163
471-108-163
471-110-163
471-112-163

Tube diam. d
6
8
10
12

Max. operating pressure 315 bars

27

Solderless pipe union with cutting-sleeve


acc. to DIN EN ISO 8434-1 and DIN 2353
Reducing connectors

Screw plugs

S

with EO2 function nut

Tube diam. d

d1

473-806-351
473-806-391
473-808-371

6
6
8

M141.5
M201.5
M161.5

473-808-392
473-810-391
473-810-371

8
10
10

M181.5

d1

466-411-001
466-413-001
466-416-001
466-418-001
466-419-001

G
G
G
G
G

1A
/2 A
/4 A
3
/4 A
1
/8 A

16
14
12
16
7

466-431-001
466-435-003
466-439-001

M101
M141.5
M181.5

7
11
12

1
1

Vent plug

S

Cone plug

Order No.

Order No.

[
Fig. 1

Order No.

Tube diam. d
6
8
10
12

Order No.

d1

Figure

466-431-006
466-431-005
466-431-009

M101
M101
G 1/8

7
7
7

1
2
2

1-0103-EN

460-706-001
460-708-001
460-710-001
460-712-001

Fig. 2

28

Accessories

Fixing bolts
Order No

d1

d2

Material

DIN84-M35-4.8
DIN84-M58-4.8
DIN84-M516-4.8
DIN84-M520-4.8
DIN84-M616-4.8
DIN84-M620-4.8
DIN84-M625-4.8

M3
M5
M5
M5
M6
M6
M6

5
8
16
20
16
20
25

5.5
8.5
8.5
8.5
10
10
10

Order No.

d1

d2

WAF

Material

DIN912-M420-8.8
DIN912-M616-8.8
DIN912-M625-8.8
DIN912-M660-8.8
DIN912-M816-8.8

M4
M6
M6
M6
M8

20
16
25
60
16

7
10
10
10
13

14
18
18
18
12

3
5
5
5
6

steel

38='#

steel
[

S!

38=( !

F05

S!

Order No.

d1

WAF

Material

DIN931-M630-5.8

M6

30

18

10

steel

38=("

Q
S!

d1

d2

Material

DIN7513-BM420
DIN7513-BM425
DIN7513-BM510
DIN7513-BM616
DIN7513-BM625

M4
M4
M5
M6
M6

20
25
10
16
25

7
7
8.5
10
10

steel

38=&$ "

Order No.

S!

Nuts

Thread

DIN934-M5-8
DIN934-M6-8
DIN936-M141.5-5
DIN936-M161.5-5
DIN936-M201.5-5

M5
M6
M141.5
M161.5
M201.5

WAF

4
5
8
8
9

8
10
22
24
30

e
9.2
11.5
25.4
27.7
34.6

Material
T

Order No.

steel
F05

Lock washer

1-0103-EN

M5
M6
M8
M10
M12
M14
M16
M18
M20

d1

d2

5.3
6.4
8.4
10.5
13
15
17
19
21

9
10
13
16
18
22
24
27
30

0.6
0.7
0.8
1
1.1
1.2
1.3
1.5
1.5

Material

0.9
0.9
1.2
1.5
1.5
1.8
1.9
2.2
2.2

spring steel

650-050
650-060
650-080
650-100
650-120
650-140
650-160
650-180
650-200

for bolt

S!

W
Order No.

29

Accessories

Fixing clips
b

l1

l2

602-001
604-001
606-010
608-001
610-001
612-001

2.5
4
6
8
10 or 1/8"
12

10
10
10
10
10
20

3.5
5.5
5.5
5.5
5.5
6.8

11.25
18.5
20.5
23.5
25.5
35

5
9
10
12
13
18

1.5
1.5
1.5
1.5
1.5
2

Order No.

for tube diam. for tube


D
diam.

l1

l2

602-002
604-002
604-003

2.5
4
4

10

3.5
5.5
5.5

13.8
22.6
26.6

[!

for tube diam.


D

S
[

5
9
9

[!

1.5

2
2
3

Order No.

S
[

l1

l2

608-003

8/4

10

5.5

34

12

1.5

[!

Order No.

for tube diam.


D

l1

l2

604-004
606-014
608-004
610-004

12
14 or 1/4"
18 or 3/8"
20 or 1/2"

24
30
36
36

14
15
20
20

5.5
6.3
7
7

27
32.5
40
40

13
16
21
21

1.5
2
2
2

S
[!

Order No.

for tube diam.


diam.

for tube
b
d

l1

l2

5.5
5.5
5.5
5.5
4.8
4.8
4.8
4.8
4.8
4.8
4.8
4.8
4.8
4.8
4.8
4.8
4.8
4.8

42
46
50
58
39
45
51
57
64
43
51
59
68
76
45
55
67
77

30
34
38
46
27
33
39
45
52
31
39
47
56
64
33
43
55
65

1.5
1.5
1.5
1.5
1
1
1
1
1
1
1
1
1
1
1
1
1
1

Order No.

for tube diam. or


socket diam. of tee
D

Material
[

30

mild steel

[!

1-0103-EN

10

4
5
6
8
2
3
4
5
6
2
3
4
5
6
2
3
4
5

4
4
4
4
6
6
6
6
6
8
8
8
8
8
10
10
10
10

604-014
604-015
604-016
604-018
DIN 72573-26-ST
DIN 72573-36-ST
DIN 72573-46-ST
DIN 72573-56-ST
DIN 72573-66-ST
DIN 72573-28-ST
DIN 72573-38-ST
DIN 72573-48-ST
DIN 72573-58-ST
DIN 72573-68-ST
DIN 72573-210-ST
DIN 72573-310-ST
DIN 72573-410-ST
DIN 72573-510-ST

Accessories

Steel tubing

s
0.03

WV-RO2.50.5 VERKU
WV-RO40.7 VERZI
WV-RO60.7 VERZI
WV-RO80.7 VERZI
WV-RO81 VERZI
WV-RO100.7 VERZI

2.5
4
6
8
8
10 *)

0.5
0.7
0.7
0.7
1
0.7

*) da 0.07

Minimum bending radius r


bent with
bent with
mandrel
grooved disk
5
8
25
46
46
76

7
12
19
19
27

Design
pressure
[bar]

Burst
pressure
[bar]

580
500
320
230
340
180

1410
1220
850
675
840
550

Order No.

da
0.05

VERKU = copper-plated
VERZI = 25 m alvanization Cr3 thick-film passivated. Length delivered 5 m. Stainless steel tubing on request.
S

EN10305-4, Cr-6 free


s

Order No.

da
0.08

982-120-040
982-120-060
982-120-080
982-120-100
982-120-120
982-120-150
982-120-180

4
6
8
10
12
15
18

1
1
1
1
1.5
1.5
1.5

Minimum bending radius r


with manual
with electrical
bending device 1)
bending device

16
22
27
29

10
9
12
15
18
22.5
36

b
SX

Seamless cold-drawn tube for hydraulic and delivery lines according to EN10305-4
1)

Tube bending device, order No. 248-803.20

Material properties:
galvanic zinc coating (blue-white) on the outside
thick-film passivated
deposit thickness 9-12 m
Cr6 free

Tube bending device


This device contains all parts needed to bend tubes with a 4, 6, 8 and 10 mm outside diameter. Thin-walled steel tubes with a 10 mm outside diam.
may be slightly flattened at the outer bend, but that is not essential with regard to strength or reduction of cross section.
Inner bending radius tube
tube
tube
tube

4 mm outside tube diam.: 10 mm


6 mm outside tube diam.: 16 mm
8 mm outside tube diam.: 22 mm
10 mm outside tube diam.: 27 mm

"#"

Back stop
Back stop

$

%%

Bending lever

1-0103-EN

&

Order No. 248-803.20


There is a special grooved disk for the bending tube with 12 mm o.d, order No. 248-803.17

Tapped holes for


displaceable back stops
in accordance with tube
diameter.

$

For older bending devices a retrofitting set for the bending tube with 4 mm is available, order No. 248-803.16

31

Accessories

Plastic tubing
WVN715, without plasticizer

Order No.

1)

WVN716, flexible (containing plasticizer)

WVN715-RO2.50.5
WVN715-RO40.85
WVN715-RO61
WVN715-RO61.25
WVN715-RO81.25

2.5
4
6 0.1
6
8

0.5
0.85
1
1.25
1.25

WVN715-RO101.5
WVN715-RO121
WVN715-RO121.5

10
12 0.15
12

1.5
1
1.5

WVN716-RO40.85
WVN716-RO61.25
WVN716-RO81.25

4
6 0.1
8

0.85
1.25
1.25

2)

Perm.
operating
press. 3)
[bar]

Burst
press.
[bar]
a

da

+0.15
di 0.05

Smallest permissible
bending radius r bent
freehand
with fixture

1.5
2.3
4
3.5
5.5
7
10
9

25
38
63
63
76

9
14
21
21
28

66
72
53
70
49

198
216
159
210
147

89
110
110

35
45
45

47
24
38

141
72
114

38
63
80

14
21
30

36
35
25

108
105
75

2.3
3.5
5.5

Color: natural colors, black lettering. Tubing available in green, red, black or brown on request.
Tubing with other dimensions or also filled with NLGI grade 2 grease or fluid grease on request.

b
SX

Important note: For screwed tubing joints only use unions with reinforcing sockets!
Material WVN715: PA 12 H: polyamide 12, semirigid, unplasticized as per DIN 73378, stabilized against heat and aging.
(black tubing) PA 12 HL: polyamide 12 , semirigid, unplasticized as per DIN 73378, stabilized against light, heat, and aging.

Material WVN716: PA 12 PH: polyamide 12, flexible, semirigid, unplasticized as per DIN 73378, stabilized against heat and aging.
(black tubing) PA 12 PHL: polyamide 12, flexible, unplasticized as per DIN 73378, stabilized against light, heat, and aging.
Material properties:
- very good resistance and insensitivity to oils, greases, lubricants, all fuels, chlorinefree detergents and solvents.
- At room temperature good resistance to diluted mineral acids, organic acids, bases and saline solutions 4)
- inappropriate for concentrated mineral acids, concentrated acetic acid, phenols, cresols, chlorinated hydrocarbons, chlorine, acetones and ketones.
Permissible operating temperature: approx. 60 C to +80 C
1)
2)

The desired length. e.g. 50 meters, has to be added to the order No. Order example: WVN716RO6x1.25x50M
These minimal radii can be produced with the help of appropriate bending devices.
The tubing has to be heated to 150 C for this purpose. The maximum duration of heating is 20 seconds.

3)

20 s (rated)
V
The operating pressures were determined by using DIN 73 378 acc. to the formula P =
.
dm

s = rated wall thickness [mm];


dm = da s;
V = reference tension N/mm2 at 23 C

At higher temperatures the pressure drops in keeping with the pressure efficiency as per DIN 73378.
Temperature ra [C]
up to 30
up to 40
up to 50
up to 60
up to 70
up to 80

In borderline cases it is advisable to contact SKF Lubrication Systems.

1-0103-EN

4)

Pressure efficiency [%]


83
72
64
57
52
47

32

Accessories

The end of the tubing


is provided with
a claw groove for
quick connectors

Hoses

"

for main lines, operating pressure: 45 bars (for short time only)

Order No.

2)

714-...(-VS)
716-...(-VS)
718-...(-VS)

Material:

2)

Order No.

Order No.

714-...-K
716-...-K
718-...-K

714-...-M(-VS)
716-...-M(-VS)
718-...-M(-VS)

With tapered
sleeve and
socket union
on both ends

Tube
diam.

Thread

Rubber

Metalbraided

Max.
increase
in volume
at 80 bars

Order No.

d1

d3

d2

d4

[cm/m]

714-...-MK
716-...-MK
718-...-MK

4
6
8

M81
M101
M141.5

11
13
15

12 0.5
14 0.8
16 0.8

2.5
3.6
4.4

Metalbraided
With tapered
sleeve and
socket union
on both ends

;,>aSTa[T]VcW

Standard

A\

X]

Hose: mineraloilresistant CR rubber inside; 2 layers of braided rayon;


outside rubber conditionally oilresistant, resistant to light cracks and ozone.
Metal braid: galvanized steel wire; tube ends: galvanized steel tubing.

S!
S#

,!

$g
S!

for secondary lines, operating pressure 15 bars (for short time only)
"

Standard
With tapered sleeve and
socket union on both ends

Tube
diam.

Thread

Rubber

Order No.

Order No.

Order No.

d1

d3

d2

734-...3)

734-...-VS

M8x1

8.8

Socket union

S"

With claw groove for


quick connectors

Material:

3)

734-...-K

3)

Double tapered
sleeve

Hose: oilproof rubber inside and outside with a layer of braided rayon
Tube ends: steel tubing
The ends of the tubing are bonded to the hose and cannot be detached.

Permissible operating temperature: 30 C to +70 C


1)

Order length in mm; other lengths available.

Standardized lengths 5 mm with 4 tubing: 180, 220, 260, 300, 380, 420, 450, 500, 580
with 6 tubing: 220, 300, 340, 380, 420, 500, 580
with 8 tubing: 340, 450, 580

Order examples:
Standard with socket unions and tapered sleeves, 4 tubing, 300 mm lang, order No.: 714-300-K
Standard,
4 tubing with claw grove for quick connectors, 300 mm long, order No.: 714-300-VS
Metal-braided,
6 tubing, 420 mm lng, order No.: 716-420-M
Metal-braided,
8 tubing, with claw grove for quick connectors, 450 mm long, order No.: 718-450-M-VS
For Version with claw groove on ends of tubing for quick connectors, order No.: ...-VS

3)

Important note: To avoid damages do not use these hoses as main lines but only to connect
distributors to lube points.

1-0103-EN

2)

33

Accessories
The end of the tube is
provided with a claw
groove for quick
connectors

Hoses suitable for self-installation, operating pressure 45 bars

Tube Male body


diam.
d1
Order No.
4
6
8
1)
2)

WAF

406-704-001(-VS)
406-706-001(-VS)
406-708-001(-VS)

2)
2)
2)

Shell

Hose

Order No.

8
10
13

406-804-001
406-806-001
406-808-001

WAF
14
17
19

Order No.

Hose
diam.
d2

1)

WVN701-4
WVN701-6
WVN701-8

11
13
15

Increase
in volume
at 40 bars
[cm/m]

F05

1
1.4
1.4

Please quote length when ordering. Max. length available 20 m.


For Version with claw groove on ends of tubing for quick connectors, order No.: ...-VS

Material:
Hose: Perbunan, resistant to mineral oils, with two layers of braided rayon
Male body: steel, galvanized
Shell: brass
Permissible operating temperature: 40 C to +100 C

F05

Installation instructions
a) Apply thin film of oil to thread and inside of hose of parts to be connected.
b) Clamp shell in vise and screw in hose by turning it to the left up to the stop.

S!

c) Important note: To avoid damages screw in male body with a wrench up to the stop. Do not tighten!

Order No.

Tube
diam.
d1

SLH6-180
SLH8-180
SLH10-180

6
8
10

Hose
diam.Length 1)
d2
l+5
10.9
13
14.5

180
180
180

l1

Permissible
operating pressure
Rmin
[bar]

Burst
pressure
[bar]

22
30
30

19
32
44

900
830
690

225
210
175

High pressure hoses, operating pressure: 280 330 bars


S

Order length in mm; other lengths available.

Order example: highpressure hose SLH8, 600 mm long, order No.: SLH8-600
Material:

S!

X]

A\

Inner liner: PA 11/12 or PE-E


Reinforcement: 1 braided layer of synthetic fibre with high tensile strength
Outer cover: PA 11/12

Resistant to mineral oils.


Permissible operating temperature: 40 C to +100 C

1-0103-EN

34

Accessories

High pressure hoses for self-installation, operating pressure: 325 bars / 130 bars

A'

The end of the tubing is


provided with a claw
groove for quick connectors

!'

%

F05 

F05 !

The end of the tubing


is provided with a claw
groove for quick
connectors

"

#

'&$

for main line for tube diam. 6 (NW4) (connection: pump feeder) and secondary lines (connection: feeder lubrication point)

*) Take length of engaged thread and double it when determining the length of the hose.

Designation

Order No.

982-750-091
982-750-091+AF2

High press. hose, max. length supplied 50 m


High press. hose, max. length supplied 50 m
filled with NLGI grade 2 grease
Sleeve
Tube stud, straight

Tube stud, 45 angle


Tube stud, 90 angle

853-540-010
853-370-002(-VS) 1)
853-380-002(-VS) 1)
853-390-002(-VS) 1)
853-380-004(-VS) 1)
853-380-003
853-380-003-VS 1)
853-390-003(-VS) 1)

Technical data:
Hose: operating pressure: 325 bars
burst pressure: 800 bars
min. bending radius: 35 mm

Material
Hose: Inner lining: unplasticized polyester
Inner layer: braided synthetic fibers
Outer cover: weatherproof polyurethane
Sleeve, tube stud: steel, galvanized

20
30
66
2
2
13

21
35
47

Permissible operating temperature: 30 C to +70 C

) Version with claw groove on ends of tubing for quick connectors, order No.: ...-VS

(

F05 &

"$

(

F05 $

"

%#

'

for main line for tube diam. 8 (NW6) (connection: pump feeder) and secondary lines (connection: feeder lubrication point)

!

*) Take length of engaged thread and double it when determining the length of the hose.

Designation

Order No.

982-750-111
982-750-111+AF2

High press. hose, max. length supplied 50 m


High press. hose, max. length supplied 50 m
filled with NLGI grade 2 grease
Sleeve
Tube stud, straight
Tube stud, straight
Tube stud, 45 angle
Tube stud, 90 angle

Technical data
Hose: burst pressure: 840 bar
min. bending radius: min. 50 mm
Material
Hose: Inner lining: unplasticized polyamide
Inner layer: braided synthetic fibers
Outer cover: weatherproof polyurethane, black
Sleeve, tube stud: steel, galvanized

406-808-005
406-708-005
406-708-007
406-708-009
406-708-008

""

""

1-0103-EN

*) Take length of engaged thread and double it when determining the length of the hose.

Designation

Order No.

WVN711-10
WVN711-10+AF2

High press. hose, max. length supplied 100 m


High press. hose, max. length supplied 50 m
filled with NLGI grade 2 grease
Sleeve
Tube stud, straight

406-810-002
406-710-002

""

F05!!

F05 !

%
 

&(

 %(

for main lines for tube diam. 10 (NW8) (connection: pump feeder)

!"

Technical data
Hose: burst pressure: 315 bars
min. bending radius: 55 mm
Material
Hose: Inner lining: Perbunan
Inner layer: diagonally woven synthetic fibers
Outer cover: weatherproof neoprene
Sleeve: aluminum
Tube stud: steel, galvanized

Permissible operating temperature: 40 C to +100 C

35

Accessories

Rotating joints

4
4
6

air

[bar]

d1

d2 *)

[rpm]

[bar]

M81
M81
M101

100

30

G /8 A
M8x1
M10x1

WAF14

Max. pressure
oil

8
$

401-504-192
401-504-292
401-506-313

Max. Speed

&#

Order No.

Tube
outside
diam.

"'

S!

Rotating joints connect fixed tubing with oscillating and rotating machine parts.

Flow media: mineral oils, oiled compressed air


!!
"

Order No.
405-549-049
405-551-049

<'g



Banjo fitting, rotable


Tube
outside diam.

d1

4
4

M81 tap.
M101 tap.
S

!%

DLY930-2
DLY931

air

d1

[rpm]

[bar]

[bar]

G 1/4 A
R 1/8 tap.

1400

20 1)

F05 &

"

F05 &

Flow media: mineral oils, oiled compressed air


1

) 30 bars in singleline centralized lubrication systems for a short time.

Max. pressure
[bar]

1400


'

Max. speed
[rpm]

"

Tube
outside diam.

%
< 

A #cP_

Order No.

#'

Order No.

Max. pressure
oil

!$

Max. speed
Tube outside
diam.

< # $

F05!#

DLY932

Flow medium: mineral oil

"!

!

F05 #

< # $

20

10

Flow medium: mineral oil

F05!&

Q
%

Part a rotating in part b

F05!!

!($

Max. pressure
[bar]

&

408-120

Max. speed
[rpm]

%&

Order No.

Tube outside
diam.

The rotating joint is also available with nut DIN936M221.5 and spring washer DIN137-B22.
P

36

Ports tapped for solderless tube connection

< # $
<!! $

1-0103-EN

*)

F05 &

Accessories

Pressure gauges

Indication range

248-602.25
169-102-506
248-602.20
169-104 008
169-106-004

010
025
040
040
060

bars
bars / 0360 psi
bars
bars
bars

F05 #
for grease
for oil

!&

Order No.

&$

#

Fixed by means of a double tapered sleeve and socket union (solderless tube connection)
in counterbore acc. to DIN 3854/DIN 3862.

'

Order No.

Indication range

169-101-004
248-604.00
169-104-020
169-106-020
169-110-020
169-116-000
169-125-020

010 bar
025 bar
040 bar / 0580 psi / 0-4 Mpa
060 bar / 0870 psi / 0-6 Mpa
0100 bar / 01450 psi / 0-10 Mpa
0160 bar
0250 bar / 03625 psi / 0-25 Mpa

Adaptor
Order No.

301-134
301-034

M101
M141.5

''

%"

<?P
_bX
QPa

F05 #

6 #0

Washer, order No. 248-610.02, must be ordered separately for every pressure gauge.

Damped version with glycerine filling

169-102-015
169-104-015
169-106-015
169-110-015
169-125-015
169-140-001

025 bar
040 bar / 0580 psi / 0-4 Mpa
060 bar / 0870 psi / 0-6 Mpa
0100 bar / 01450 psi / 0-10 Mpa
0250 bar / 03625 psi / 0-25 Mpa
0400 bars

<?P
_bX
QPa

Mounting position

Indication range

Order No.

6 #
vertically

F05 (

Washer, order No. 248-610.02, must be ordered separately for every pressure gauge.

Version with visualization


Order No.

Indication range

Mounting position

169-101-607
169-104-011
169-106-011
169-110-010

016 bars / 01.6 MPa


040 bars / 04 MPa
060 bars / 06 MPa
0100 bars / 010 MPa

vertically

1-0103-EN

Washer, order No. 248-610.02, must be ordered separately for every pressure gauge.

m'#

m%"

F05 #
6 '0

37

Accessories

Shut-off valves
F05%
F05 &

Max.
temperature [C]

Spindleway

202-085-S

60

80

max. 3 revs.

m%#

Max. pressure
[bar]

#$

Order No.

< 



F05 (

Direction of flow optional


F05 #
!

Max. pressure
[bar]

Max.
temperature [C]

161-600-036

16

90

6 #

Order No.

!&$

< # $

5!
F0


#

*)

Ports tapped for solderless tube connection

Quick-disconnect couplings

Coupled

Coupling, complete
Order No.

Tube
diam.

207-168-2
207-188-2

6
8

d1 *)

l2

M101
M141.5

62
66,5

Flow
direction
F05!!

[!

optional

Outer coupling member

6
8

F05 &

l1
48.5
53

< #g $

Pressure loss as a function of the


flow rate based on an operating
oil viscosity of 140 mm2/s

Inner coupling member

Both coupling members are shut off when disconnected!

*)

38

"

207-168.U2

Ports tapped for solderless tube connection

Pressure loss
p (bar)

Order No.


!
Flow rate (l/min)

"

#

1-0103-EN

207-168.U7
207-188.U11

Tube
diam.

Order No.

Accessories

Relief valves
These valves are installed in distributor systems fitted with a pump without pressure
relief equipment, mainly in the main line downstream from the pump.

< g 

With longer main lines and high viscosity oils, the pressure relief time, which influences the
reversing of the distributors, can become too long. The installation of the second relief valve at a
suitable position in the main line, e.g. at half the main line length, may remedy this problem.

$

!!!&$!

Order No. 202-275-2

&(

6 #

C
0

?
6 #

Check valve = residual pressure valve 0.5 bar

!

C
A
= Outlet
P
= Inlet
T (R) = Return

"

Relief valve with bleed valve and safety valve


Order No. 202-175-30
Adaptors

*)

for tube diam. 6: Order No. 406-054


for tube diam. 8: Order No. 301-020
for tube diam. 10: Order No. 410-163

0!

#

Fitted to reservoir

Bleed valve

0!
Relief valve

!&

!

%

Safety valve
30 bars

'#
'

#'

< #g $

For P and R
two adapters each 408-160
washers
508-108

0 0!
6 #

%
!$

!(
#"

%&

1-0103-EN

Check valve =
residual pressure valve 0.5 bar

*)

Ports tapped for solderless tube connection

39

Accessories

Safety valves, adjustable (poppet valve)


Hydraulic characteristics

6
12
12
25
25
35
60
60

40
40
40
40
40
40
70
70

80 C

20 to 1000

NBR
NBR
FKM (FPM)
NBR
FKM (FPM)
NBR
NBR
FKM (FPM)

%

to
to
to
to
to
to
to
to

&

see
pressureloss
parameter

1
3
3
4
4
4
12
12

Seal

! $
"$$
#($

WVN200-10E6
WVN200-10E12
WVN200-10E12-S8
WVN200-10E25
WVN200-10E25-S8
WVN200-10E35
WVN200-10E60
WVN200-10E60-S8

Oil
Viscosity
temperature range
max.
mm2/s

6 #

Order No.

Adjustable Operating
pres. range pres. max.
[bar]
[bar]

6 #

Rated
flow rate
[l/min]

General characteristics

#
0

Design:

poppet valve with hydraulic cushioning


directly controlled
Lubricant:
oil
Connecting thread: G 1/4
Mounting position: optional

%%
'
!$

Setting screw

Adaptors *)

Pressure loss parameter


4

for valves

2 /s

140

for tube diam. 8: Order No. 301-020


for tube diam. 10: Order No. 410-163
for tube diam. 12: Order No. 412-163

mm

Washer:

Order No. 508-108

for valve
0

WVN200-10E60

for tube diam. 8: Order No. 408-403W


for tube diam. 10: Order No. 410-403W
Washer:
Order No. 508-108

10

Flow rate Q [l/min]

With increasing flow rate, the pressure upstream from


the valve will also rise in accordance with the curves.

Washer
508-108

If installed on a reservoir,
use two special adapters 408-160 with
long tube ends.
*)

< #g $

for tube 8

Ports tapped for solderless tube connection

VPM-RV4
VPM-RV
VPM-RV8
VPM-RV10

4
6
8
4
6
8
10

Series

R /8 tap.
R 1/8 tap.
R 1/8 tap.

10
10
10

100
315
315

LL
L
L

M101 tap.
M101 tap.
M101 tap.
M101 tap.

10
10
10
10

100
315
315
315

LL
L
L
L

VPKG-RV

R 1/8 tap.

100

LL

VPKM-RV
VPKM-RV-S3
VPKM-RV-S4

6
6
6

M101 tap.
M101 tap.
M101 tap.

3
3
2

100
100
100

LL
LL
LL

Check valves for quick connectors, see page 18.

40

Presure,
max.
[bar]

Opening
pressure
[bar]

CdQTS

VPG-RV
VPG-RV6
VPG-RV8

Tube
diam. d1

Order No.

CdQTS

Check valve (Kugelventile)

With cutting sleeve


and union nut

LL-series = extra light version, L-series = light version

1-0103-EN

/s

50

\X] $
\Pg$

Pressure loss p [bar]

WVN200-10E6 to
WVN200-10E35

Accessories

Safety valves, (ball valves) for flow rates from 0.5 to 2 l/min
$

Order No.

0.4

04

M101

Opening pressure
[bar]
Marking

marking

d1 *)

l1

WAF

61

14

0.5
3
8
12
16
20
40

05
3
8
12
16
20
40

M101

0.04
3
5
12
16
20
32

0
3
5
12
16
20
32

M141.5

71

17

WVN200-10B0
WVN200-10B0.5
WVN200-10B1
WVN200-10B32

10

0.04
0.5
12
32

0
05
12
32

M161.5

80

19

161-212-054 1)

20

20

M141.5

84.5

17

WVN200-8B0
WVN200-8B3
WVN200-8B5
WVN200-8B12
WVN200-8B16
WVN200-8B20
WVN200-8B32

[
F05

WVN200-6B0.5
WVN200-6B3
WVN200-6B8
WVN200-6B12
WVN200-6B16
WVN200-6B20
WVN200-6B40

Tube
diam.

M81

<'g cP_

WVN200-4A0.4-S1

04
5
8
12
16
25

0.4
5
8
12
16
25

&#

F05 #

d1 *)
%

WVN200-4A0.4
WVN200-4A5
WVN200-4A8
WVN200-4A12
WVN200-4A16
WVN200-4A25

Opening pressure
[bar]
Marking

Tube
diam.

!

Order No.

) This valve is designed as a plunger valve. Because of this design it can also be used for regulating tasks,
whereas the ball valves should be used as safety valves..

WVN200-10D120-S1
WVN200-10D220-S1

l1

50
75
120
220

50
75
120
220

84

10

120
220

120
220

87

F05 &

Opening pressure
[bar]
Marking

!

WVN200-8D50
WVN200-8D75
WVN200-8D120
WVN200-8D220

Tube
diam. d

Order No.

F05 &

1-0103-EN

Cutting sleeve screw unions according to DIN 2353

*) Ports tapped for solderless tube connection

41

Accessories

Oil reservoirs plastic


Plastic reservoirs
Level
indicator WS

Type of contact

Seal
material

K1
KW1
KW1-S2

for min. filling level


for min. filling level

NC
NC

NBR

K3-S2
KW3-S1
KW3-S3
KW3-S5

for min. filling level


for min. and max. filling level
for min. filling level with advance warning

changeover
1 NC, 1 NO

NBR

for min.
for min.
for min.
for min.

changeover
2 NCs
changeover
NBR

level
level with advance warning
level
level with advance warning

"

NBR
NBR
NBR
FKM (FPM)

! !
%

(

(
"g'$

5X[[Tab^RZTcfXcWbRaTT]

%%

filling
filling
filling
filling

K6-S5
KW6-S1
KW6-S2
KW6-S81
KW6-V57

"

Reservoir
capacity [liters]

Order No.

&

"$

!#&

ATcda]6!

'$!g


$

!$

FB

< #g $ 

"

'

"%

!

%(

U^acdQTSXP\ 

< %g $ 

&

1-liter reservoir (shown: KW1)

U^acdQTSXP\ 

3-liter reservoir (shown: K3-S2)


!(
#$



5X[[Tab^RZTcfXcWbRaTT]

FB

"g'$
!

!!'

!#"

!'

'"


< %g $

('

U^acdQTSXP\ 

42

6-liter reservoir (shown: KW6-S1)


Ports tapped for solderless tube connection to DIN 2367

1-0103-EN

&'

1)

Accessories

Oil reservoirs metal


Metal reservoirs
Reservoir
capacity [liters]

Order No.
B3-S1
BW3-S81
162-210-005
B7
BW7-S6
BW7-S7
BW7-S8
BW7-S11
BW7-S12
162-310-005

Level
indicator WS

Type of contact

Seal
material

for min. filling level


for min. filling level

changeover
changeover

NBR
FKM (FPM)
NBR

for min.
for min.
for min.
for min.
for min.
for min.

2 NCs
2 NCs
changeover
1 NO, 1 NC
1 NO, 1 NC
changeover

NBR
NBR
NBR
FKM (FPM)
NBR
NBR
NBR

and max. filling level


filling level with advance warning
filling level
filling level with advance warning
filling level with advance warning
filling level

Filler socket with screen

!!

FB

!%&

#

!!!$

%$$

! %

FB

##

&

!&

"

(
!'

6 !

!"

"!

3-liter reservoir
!'

6-liter reservoir (shown: BW7-S6)

Oil level gauges for metal reservoir


Reservoir
capacity [liters]

l1

152
190
215
279
305

127
165
190
254
280

6
6
15 and 30
50
100

F05 (

< !

1-0103-EN

995-003-044
995-003-040
995-003-041
995-003-042
995-003-043

Order No.

Type: NBR
FKM (FPM) on request
!%

!($

43

Accessories

Filler coupling for oil and fluid grease


Coupling plug

Order No.

Fig.

Respective
dust cover
Order No.

995-001-501
995-001-502
995-000-705
995-001-260

1
1
2
3

G 1/4
G 1/2
G 1/4
G 1/2

57.5
82

83

995-001-503
995-001-504

Respective
coupling socket
Order No.
995-002-073
995-001-950
995-001-500

'"

0

!$
0

&

!
#

;
Fig. 1

Fig. 2

Fig. 3

Topping-up pumps
Drum (kg)

Medium

Operating

Trolley

169-000-004
169-000-012
169-000-016
169-000-056

15
10
20
25

NLGI 1,2

manually operated

no

169-000-082
169-000-084

25 / 50
25

00/000
00/000

manually operated
manually operated

yes
yes

Fig.

169-000-042
169-000-054

25
50

NLGI 1,2

manually operated

yes

169-000-342
169-000-018

25
25

NLGI 1,2
00 to 2

manually operated
pneum. operated

no
yes

\Pg#$

\Pg"$

%"$

Order No.

1-0103-EN

Fig.

44

1-0103-EN

Notes

45

1-0103-EN

Notes

46

The Power of Knowledge Engineering


Seals

Bearings
and units

Mechatronics

Lubrication
systems

Services

Drawing on five areas of competence and application-specific expertise amassed over more than 100
years, SKF brings innovative solutions to OEMs and production facilities in every major industry worldwide. These five competence areas include bearings and units, seals, lubrication systems, mechatronics
(combining mechanics and electronics into intelligent systems), and a wide range of services, from 3-D
computer modelling to advanced condition monitoring and reliability and asset management systems.
A global presence provides SKF customers uniform quality standards and worldwide product availability.

Additional brochures for further information


1-0116-EN
1-9201-EN

SKF Lubrication Systems Germany AG


Berlin Plant
Motzener Str. 35/37 12277 Berlin
PO Box 970444 12704 Berlin Germany

Filters
Transport of Lubricants in Centralized Lubrication Systems

This brochure was presented to you by:

Tel. +49 (0)30 72002-0


Fax +49 (0)30 72002-111

SKF is a registered trademark of the SKF Group.


SKF Group 2011
The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can
be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein.
1-0103-EN June 2011
This publication supersedes publication 1-0103-1-EN.

skf.com/lubrication

Anda mungkin juga menyukai