2009
9. SERVICE MODE
9.4
9.4.1
Process adjustment
High Voltage Auto Adj. (High Voltage Adjustment)
A. Function Automatically adjust current values and voltage values of a transfer, separation (AC), separation (DC), developing bias respectively. B. Usage Conduct this adjustment when replacing the high voltage unit /1, /2 (HV /1, /2).
D. Procedure
Do not conduct this adjustment in the field. 9.4.3 HV Adjustment (Transfer) (High Voltage Adjustment)
Do not conduct this adjustment in the field. 9.4.4 HV Adj. (Separation AC) (High Voltage Adjustment)
Do not conduct this adjustment in the field. 9.4.5 HV Adj. (Separation DC) (High Voltage Adjustment)
Do not conduct this adjustment in the field. 9.4.6 HV Adj. (Charging grid volt.) (High Voltage Adjustment)
Do not conduct this adjustment in the field. 9.4.7 HV Adj. (BiasDevelop. DC) (High Voltage Adjustment)
Do not conduct this adjustment in the field. 9.4.8 Transfer Guide Confirm (High Voltage Adjustment)
159
A. Function Apply toner to the cleaning blade and drum to prevent the damage.
Note Perform this only when changing the cleaning blade. Otherwise, the cleaning blade special parts counter is reset, thus making it impossible to implement the auto blade change in the right timing. Apply setting powder to the cleaning blade and drum. C. Procedure
160
Field Service Ver.2.0 Sep. 2009 9.4.10 Auto Drum Potential (Drum Peculiarity Adj.)
9. SERVICE MODE
Automatically adjust the developing bias value, charging voltage and grid voltage to be suitable for the drum.
B. Usage Conduct this adjustment when replacing the drum, developer, and write unit.
C. Procedure
161
A. Function
9. SERVICE MODE 9.4.11 Auto Maximum Density Adj. (Drum Peculiarity Adj.)
A. Function Automatically adjust the maximum density that is suitable for the drum.
B. Usage Conduct this adjustment when replacing the drum, developer, and write unit.
C. Procedure
162
Field Service Ver.2.0 Sep. 2009 9.4.12 Auto Dot Diameter Adj. (Drum Peculiarity Adj.)
9. SERVICE MODE
Automatically adjust the dot diameter of laser beam that is suitable for the drum.
B. Usage Conduct this adjustment when replacing the drum, developer, and write unit.
C. Procedure
163
A. Function
B. Usage Conduct this adjustment when replacing the drum, developer, and write unit. Conduct this adjustment when the print density is not even.
C. Procedure
5. Select A3 or 11 x 17 paper, and press the Start button to output a test pattern. 6. Adjust laser intensity of LD1 and LD2.
Standard value: Compare image patterns created by the LD1 and LD2. Confirm that density is uniform (1 gap is OK) as per the following figure, and the highlighted patterns start between the two reference lines [1].
[1]
57gaf3c009na
7. When the value is not within the standard value, press [SERVICE]. 8. "LD offset adjustment screen"
Press [460mm] for the laser you want to adjust (LD1 offset or LD2 offset). Enter a value through the numeric keys and press [Set] and then the [COPY]. Setting range: -128 (lighter) to +127 (darker)
9. Select A3 or 11 x 17 paper, and press the Start button to output a test pattern. 10. When the value is not within the standard value, press [SERVICE] to repeat steps 5 to 9 until the standard
value can be obtained.
164
Field Service Ver.2.0 Sep. 2009 9.4.14 Auto Gamma Adj. (1dot) (Drum Peculiarity Adj.)
9. SERVICE MODE
B. Usage Conduct this adjustment when replacing the drum, developer, and write unit.
C. Procedure
Do not conduct this adjustment in the field. 9.4.16 LD2 Bias Adjustment (Drum Peculiarity Adjustment)
165
A. Function
A. Function Agitate the recycle toner that is back to the developer to prevent the overflow toner to the conveyance section. B. Usage Conduct this adjustment when black spots (toner) appear on the print-out after removing/inserting the photo conductor section. C. Procedure
5. After the rotation stops, press [COPY]. 6. Select the A3 or 11 x 17 paper. Press the Start button to output 10 blank papers, thus cleaning the drum. 7. When the black spot does not disappear, press [SERVICE] to repeat steps 4 to 6.
9.4.18
166
9. SERVICE MODE
Adjust when the transfer and separation functions and fusibility do not work satisfactorily with the standard adjustments because of using special papers.
B. Usage This setting is applied when you select [User] as the paper type. By default, the following data are inputted. Fusing temperature for Japan: High quality paper of 62 to 71 g/m2 Fusing temperature for the other countries: High quality paper of 72 to 80 g/m2
Note Input data according to instructions of KMBT field support section. C. Procedure
4. Input data for the selected item, and press [Set]. 5. Repeat steps 3 and 4 to configure other items.
167
A. Function
A. Function Reset the adjustment values of the process adjustment to the factory initial data or the installation initial data. B. Usage Conduct this adjustment when the initialization cannot be done because of the various change by CE.
C. Procedure
168
2009 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. Use of this manual should be strictly supervised to avoid disclosure of confidential information. Printed in Japan CCA0Y5-M-FE2-0000