Anda di halaman 1dari 44

MBTS Initial Data Configuration based on LMT

www.huawei.com

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

References

BSC6900 LMT User Guide

BSC6900 Initial Configuration Guide


BTS3900 Initial Configuration Guide

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page2

Objectives

Upon completion of this course, you will be able to:

Know the principle of data configuration


Master BTS3900 GSM initial data configuration through Web LMT

Understand the meaning of some important parameters

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page3

Contents
1. Web LMT Introduction

2. Steps of Data Configuration

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page4

Web LMT Introduction

The LMT provides graphical user interface (GUI) for you to

operate and maintain the BSC6900 and BTS.

The alarm management, trace management, performance monitoring, and device maintenance can be performed through menu operations.

The MML commands can be run for data configuration and

O&M on the Web-LMT.

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page5

Web LMT Introduction

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page6

MML Command Window

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page7

Contents
1. Web LMT Introduction

2. Steps of Data Configuration

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page8

Steps of Data Configuration


START

Configuring the Equipment Data


Configuring the Logical Data Configuring the Transmission Data Configuring the BTS Clock Activating the BTS Configuration

END
Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved. Page9

Configuring the Equipment Data


START
Configuring the Equipment Data
3 1 2

ADD BTS ADD BTSCABINET ADD BTSRXUCHAIN

Configuring the Logical Data Configuring the Transmission Data

ADD BTSRXUBRD
SET BTSRXUBP

Configuring the BTS Clock


Activating the BTS Configuration

END
Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved. Page10

Step 1 ADD BTS

ADD BTS: < BTSID>, <BTSNAME>, <BTSTYPE>, < BTSDESC >,


<SEPERATEMODE>,<SERVICEMODE>,<FLEXABISMODE >, <ABISBYPASSMODE>,<ISCONFIGEDRING >,<MPMODE >, <MAINPORTNO >,<IPPHYTRANSTYPE >,<SRANMODE>;

BTSID: ID of the BTS. The BTS ID must not conflict with other BTS IDs in the BSC. BTSNAME: Name of the BTS. The BTS name must not conflict with other BTS names in the BSC. BTSTYPE: Type of the BTS BTSDESC: Peer equipment type of the BTS. This parameter indicates whether to connect the BTS to the BSC or cascade the BTS to another BTS.

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page11

Step 1 ADD BTS

ADD BTS

SEPERATEMODE: Whether to enable the BTS to support the separation between the physical board and logical TRX.

SERVICEMODE: Service bearer mode of the BTS FLEXABISMODE: Service timeslot assignment mode for the BTS

ABISBYPASSMODE: Whether to enable the BTS to support bypass


ISCONFIGEDRING: Whether to enable the BTS to support ring

networking

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page12

Step 1 ADD BTS

ADD BTS

MPMODE: Timeslot multiplexing mode at the Abis interface of the BTS.

MAINPORTNO: Number of the port to which the active OML of the BTS is connected

PPHYTRANSTYPE: Type of the physical IP transmission medium


SRANMODE: Whether to enable the BTS to identify an object in the BTS in normalized mode, for example, to identify a board by the slot No., subrack No., and cabinet No. and to identify a transmission port by the port No. in a board

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page13

Step 2 ADD BTSCABINET

ADD BTSCABINET: <IDTYPE>, <BTSID>,<CN>, <SRANMODE>,


<TYPE>, <CABINETDESC>;

CN: Number of the cabinet SRANMODE: Whether to support the SRAN mode TYPE: Type of a cabinet CABINETDESC: Descriptive information of the BTS cabinet

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page14

Step 3 ADD BTSRXUCHAIN

ADD BTSRXUCHAIN: <IDTYPE>, <BTSID>, <RCN>, <TT>,


<HCN>,<HSRN>,<HSN>,<HPN>

RCN: Number of the RXU chain or ring TT: RXU topology type, that is, RXU ring topology or RXU chain topology.

HCN: Number of the cabinet where the head board of the RXU chain

or ring is located

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page15

Step 3 ADD BTSRXUCHAIN

ADD BTSRXUCHAIN:

HSRN: Number of the subrack where the head board of the RXU
chain or ring is located.

HSN: Number of the slot where the head board of the RXU chain or ring is located.

HPN: The number of the optical port of the head board in the RXU

chain or ring.

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page16

Step 4 ADD BTSRXUBRD

ADD BTSRXUBRD: <IDTYPE>, <BTSID>, <BT>,<CN>,<SRN>,


<SN>,<RXUNAME>,<RXUCHAINNO>,< RXUPOS>

BT: Type of the newly added RXU board CN: Number of the cabinet SRN: Number of the subrack where the BTS board is located

SN: Number of the slot where the BTS board is located


RXUNAME: Name of an RXU RXUCHAINNO: Number of the RXU chain where the board is located RXUPOS: Position of the RXU board on an RXU chain

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page17

Step 4 SET BTSRXUBP

SET BTSRXUBP: <IDTYPE><BTSID><RXUIDTYPE><RXUCHAINNO


><RXUPOS ><RXUTYPE><SndRcvMode ><WORKINGSTANDARD >

SndRcvMode: RFU Antennal Sending Receiving Mode

GUI Value Range: SGL_ANTENNA(Single Feeder[1TX + 1RX]), SGLDOUBLE_ANTENNA(Single Feeder[1TX + 2RX]), DOUBLE_ANTENNA(Double Feeder[2TX + 2RX]), DOUBLEFOUR_ANTENNA(Double Feeder[2TX + 4RX]),

DOUBLESINGLE_ANTENNA(Double Feeder[1TX + 1RX]),


DOUBLEDOUBLE_ANTENNA(Double Feeder[1TX + 2RX])

WORKINGSTANDARD: Working Standard

GSM_AND_UMTS, UMTS, GSM, GSM_AND_LTE, LTE

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page18

Configuring the Logical Data


START
5

Configuring a GSM Cell Configuring the TRX Configuring the Binding Between a GSM Cell and a BTS

Configuring the Equipment Data Configuring the Logical Data Configuring the Transmission Data Configuring the BTS Clock Activating the BTS Configuration

Configuring the Binding Between a Logical TRX and a


Physical TRX Board

END
Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved. Page19

Step 5 Configuring a Cell

Configuring a GSM cell involves configuring a cell, mapping

between the cell and the OPC and frequencies for the cell.

ADD GCELL

This command is used to add GSM internal cells.

ADD GCELLOSPMAP

This command is used to add the mapping between a cell and an originating signaling point (OSP).

ADD GCELLFREQ

This command is used to add frequencies to a GSM internal cell.


Page20

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Step 5 Configuring a Cell ADD GCELL

ADD GCELL: <CELLID>, <CELLNAME>, <TYPE>, <MCC>, <MNC>,


<LAC>, <CI>;

CELLID: Index of a cell, uniquely identifying a cell in a BSC


CELLNAME: Name of a cell, uniquely identifying a cell in a BSC TYPE: This parameter specifies the frequency band of new cells. MCC: Mobile country code MNC: Mobile network code LAC: Location area code CI: Identity code of a cell
Page21

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Step 5 Configuring a Cell ADD GCELLOSPMAP

ADD GCELLOSPMAP: <IDTYPE>, <CELLID>, <CELLNAME>, <OPC>;

IDTYPE: Type of an index

CELLID: Index of a cell, uniquely identifying a cell in a BSC


CELLNAME: Name of a cell, uniquely identifying a cell in a BSC OPC: Code of the original signaling point (OSP) in the signaling network

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page22

Step 5 Configuring a Cell ADD GCELLFREQ

ADD GCELLFREQ: <IDTYPE>, <CELLID>, <FREQ1>,<FREQ2>;

FREQ1: Frequency 1 FREQ2: Frequency 2

EXAMPLE

ADD GCELLFREQ: IDTYPE=BYID, CELLID=0, FREQ1=1, FREQ2=2;

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page23

Step 6 Configuring the TRX

Configuring the TRX for the BTS. This involves configuring the logical TRX and BCCH.

ADD GTRX

This command is used to add a logical TRX and configure the binding between the logical TRX and the cell

SET GTRXCHAN (Optional)

This command is used to set the TRX channel attributes and specify the BCCH.

SET GTRXDEV (Optional)

This command is used to set the device attributes of a TRX.


Page24

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Step 6 Configuring the TRX ADD GTRX

ADD GTRX: < IDTYPE>, <CELLID>, <TRXID>, <FREQ>


<ISMAINBCCH>;

TRXID: ID of the TRX. The TRX ID must be globally unique FREQ: Frequency of the TRX, Value Range: 0~1023

ISMAINBCCH: Whether to enable the TRX to carry the main BCCH


in the cell

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page25

Step 6 Configuring the TRX SET GTRXCHAN

SET GTRXCHAN: <TRXID>,<CHNO>,<CHTYPE>,<GPRSCHPRI>,


<TSPRIORITY>;

TRXID: ID of the TRX. The TRX ID must be globally unique


CHNO: Number of the channel in the TRX CHTYPE: Type and function of the channel GRRSCHPRI: EGPRS priority type of the channel TSPRIORITY: Assignment priority level of the channel. If this

parameter is less, the assignment priority level of the channel is


higher. Value Range: 0~7

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page26

Step 6 Configuring the TRX SET GTRXDEV (Optional)

SET GTRXDEV: <POWL >,<POWT >,<OPTL >,<SDFLAG >,


<TCHAJFLAG >,<PL8PSK >,<RCVMD > ,<SNDMD >, <CPS >..

POWL: Power Level POWT: Power Type OPTL: TRX Priority SDFLAG: Shut Down Enabled TCHAJFLAG: TCH Rate Adjust Allow PL8PSK: TRX 8PSK Level RCVMD: Receive Mode SNDMD: Send Mode CPS: Allow Dynamic Shutdown TRX
Page27

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Step 7 Configuring the Binding Between a GSM Cell and a BTS

ADD CELLBIND2BTS: <IDTYPE>, <CELLID>, <BTSID>;

IDTYPE: Type of an index CELLID: Index of a cell, uniquely identifying a cell in a BSC

CELLNAME: Name of a cell, uniquely identifying a cell in a BSC


BTSID: ID of the BTS BTSNAME: Name of the BTS

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page28

Step 8 Configuring the Binding Between a Logical and Physical TRX

Configuring the binding between a logical TRX and a physical TRX

board in the BTS cabinet.

ADD TRXBIND2PHYBRD: <TRXID>, <TRXTP>, <TRXPN>,


<RXUIDTYPE>,<CN>,<SRN>, <SN>,<ANTPASSNO>;

TRXID: ID of the TRX


TRXTP: Type of the TRX board bound to the TRX TRXPN: Number of the channel bound to the TRX on the TRX board RXUIDTYPE: Index type of the RXU. GUI Value Range: RXUNAME (By RXU Name), RXUPOS (By RXU Position No), SRNSN (By Subrack No)

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page29

Step 8 Configuring the Binding Between a Logical and Physical TRX

ADD TRXBIND2PHYBRD:

CN: Number of the cabinet SRN: Number of the subrack where the BTS board is located

SN: Number of the slot where the BTS board is located


ANTPASSNO: Number of the antenna feeder channel mapped to the RXU

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page30

Configuring the Transmission Data


START
Configuring the Equipment Data Configuring the Logical Data
1

TDM/HDLC IP Over FE/GE

Configuring the Transmission Data

Configuring the BTS Clock


Activating the BTS Configuration

END
Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved. Page31

Configuring TDM/HDLC Transmission Data

ADD BTSCONNECT: <IDTYPE>, <BTSID>, <INPN>, <DESTNODE>,


<SRN>, <SN>, <PN>; INPN: Number of a BTS port INCN: Number of the in-port cabinet on a BTS INSRN: Number of the in-port subrack on a BTS INSN: Number of the in-port slot on a BTS

DESTNODE: Type of the object that connects to the BTS. Value range:
BTS, BSC6900, and DXX

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page32

Configuring TDM/HDLC Transmission Data

ADD BTSCONNECT:

SRN: Number of the subrack where the BSC6900 board connected to the BTS is located

SN: Number of the slot PN: Number of the port through which the BTS is connected to the BSC6900

EXAMPLE

ADD BTSCONNECT: IDTYPE=BYID, BTSID=1, INPN=0, DESTNODE=BSC, SRN=11, SN=0, PN=1;

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page33

Configuring IP Over FE/GE Transmission Data

Step 1 ADD DEVIP: <SRN>, <SN>, <DEVTYPE >, <IPADDR >, <MASK >

Run the ADD DEVIP command to add the device IP address of the FG2a
board.

Step 2 ADD ETHIP: <SRN>, <SN>, <PN >, <IPINDEX>, <IPADDR >, <MASK
>

Run the ADD ETHIP command to add the port IP address of the FG2a board.

Step 3 ADD IPRT: <SRN>, <SN>, <DSTIP >, <DSTMASK >, <NEXTHOP>
(Optional)

When the BSC6900 and the BTS are on different network segments, run

the ADD IPRT command to add an IP route to the BSC6900.

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page34

Configuring IP Over FE/GE Transmission Data

Step 4 SET BTSETHPORT : <IDTYPE>, <BTSID>, <PN >, <RATE >,

<MTU>

Run the SET BTSETHPORT command to set the port attributes of the BTS.

Step 5 SET BTSIP : <IDTYPE>, <BTSID>, <BTSIP >, <BSCIP>,

Run the SET BTSIP command to set the IP address of the BTS.

Step 6 ADD BTSIPRT: <IDTYPE>, <BTSID>, <DSTIP >, <DSTMASK >,

<NEXTHOP> (Optional)

When the BSC6900 and the BTS are on different network segments, run the ADD BTSIPRT command to add an IP route to the BTS.

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page35

Configuring IP Over FE/GE Transmission Data

Step 7 ADD BTSESN: <IDTYPE>, <BTSID>, <DEVTYPE>,

<MAINDEVTAB>, <BAKDEVTAB>

Run the ADD BTSESN command to add the Equipment Serial Number of the BTS..

Step 8 Add an adjacent node : ADD ADJNODE : <ANI>, <NAME>, <NODET>

ANI: Adjacent Node ID


NAME: Node Name NODET: Node Type

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page36

Configuring IP Over FE/GE Transmission Data

Step 9 Add an IP path ADD IPPATH :<ANI>, <PATHID >, <ITFT >,

<TRANST> ,< PATHT>,<IPADDR> , <PEERIPADDR >, <TXBW> , <RXBW


>

ANI: Adjacent Node ID PATHID: IP path ID ITFT: Interface Type

TXBW: Forward Bandwidth


RXBW: Backward Bandwidth

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page37

Configuring the BTS Clock


START
Configuring the Equipment Data Configuring the Logical Data Configuring the Transmission Data

Configuring the BTS Clock


Activating the BTS Configuration

1 SET BTSIPCLKPARA 2 SET BTSCLK

END
Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved. Page41

Set BTS IP Clock Server

Set BTS IP Clock Server SET BTSIPCLKPARA :<BTSID>, <


CLKPRTTYPE >, < SYNMODE >,< SYNTIMEDAY >,< SYNTIMEHOUR >,
< SYNTIMEMIN >,< MASTERIPADDR >,

BTSID: BTD Index CLKPRTTYPE : Clock Protocol Type SYNMODE : Clock Synchronization Mode SYNTIMEDAY : Days of Inter Sync Period SYNTIMEHOUR : Hours of Inter Sync Period SYNTIMEMIN : Minutes of Inter Sync Period

MASTERIPADDR : Master Clock Server IP Address


Page42

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Set Clock Type of BTS

Set Clock Type of BTS SET BTSCLK (Optional): <BTSID>


<ClkType> <TRANSTYPE>

BTSID: BTS Index CLOCK TYPE: INT_CLK(Internal Clock), TRCBSC_CLK(Trace BSC Clock), EXTSYN_CLK(External Sync clock), IP_TIME(IP Clock), IP_TRANSFER(Trace Transport Clock), TRCGPS_CLK(Trace GPS Clock), UM_CLK(Um Clock), PEER_CLK(Peer Clock), SYNETH_CLK(SynEth Clock) TRANS TYPE: E1(E1), T1(T1), FE(FE)

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page43

Activating the BTS Configuration


START
Configuring the Equipment Data Configuring the Logical Data Configuring the Transmission Data

Configuring the BTS Clock


Activating the BTS Configuration ACT BTS

END
Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved. Page44

Activating the BTS Configuration

CHK BTS: <IDTYPE>, <BTSID>;

Use this command to check the BTS data integrity.

ACT BTS: <IDTYPE>, <BTSID>;

IDTYPE: Index type of the BTS.


BTSID: ID of the BTS. BTSNAME: Name of the BTS

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page45

Summary

The concept of Web LMT

Initial GSM data configuration steps of BTS3900


Configuring the Equipment Data, Logical Data, Transmission

Data, Clock Data

Activating the BTS Configuration

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Page46

Thank you
www.huawei.com

Anda mungkin juga menyukai