Anda di halaman 1dari 5

MPMC

Unit 5 1. State the features of 8051 microcontroller. The main features of 8051 microcontroller are: 1) 8051 have 128 bytes of RAM 2) 8051 have 128 user defined flags 3) it consist of 16 bit address bus 4) it also consist of 3 internal and two external interrupts 5) less power usage in 8051 with respect to other micro-controller 6) it consist of 16-bit program counter and data pointer 7) 8051 can process 1 million one-cycle instructions per second 8) it also consist of 32 general purpose registers each of 8 bits 9) ROM on 8051 is 4 Kbytes in size 10) it also consist of Two 16 bit Timer/ Counter 2. Explain the operation of stack pointer in 8051 microcontroller. The stack pointer (SP) is an 8-bit register at location 81H. A stack is used for temporarily storing data. It operates on the basis of last in first out (LIFO). Putting data onto the stack is called "pushing onto the stack" while taking data off the stack is called "popping the stack." The stack pointer contains the address of the item currently on top of the stack. On power-up or reset the SP is set to 07H. When pushing data onto the stack, the SP is first increased by one and the data is then placed in the location pointed to by the SP. When popping the stack, the data is taken off the stack and the SP is then decreased by one. Since reset initialises the SP to 07H, the first item pushed onto the stack is stored at 08H (remember, the SP is incremented first, then the item is placed on the stack). However, if the programmer wishes to use the register banks 1 to 3, which start at address 08H, he/she must move the stack to another part of memory. The general purpose RAM starting at address 30H is a good spot to place the stack. To do so we need to change the contents of the SP. MOV SP, #2FH. 3.Write an 8051 assembly language program to add two 8 bits number data stored in internal memory and store the result in register R2. MOV A,#44;LOAD ACC WITH 44H ADD A,#66;ADD 66H WITH THE CONTEN MOV R2,A;MOVE RESULT IN REGISTER HERE: SJMP HERE 4. Explain register bank? Register banks in the 8051 As mentioned earlier, a total of 32 bytes of RAM are set aside for the register banks and stack. These 32 bytes are divided into 4 banks of registers in which each bank has 8 registers, RO R7. RAM locations from 0 to 7 are set aside for bank 0 of RO R7 where RO is RAM location 0, Rl is RAM location 1, R2 is location 2, and so on, until memory location 7, which belongs to R7 of bank 0. The second bank of registers RO R7 starts at RAM location 08 and goes to location OFH. The third bank of RO R7 starts at memory location 10H and goes to loc ation 17H. Finally, RAM locations 18H to 1FH are set aside for the fourth bank of RO R7. The following shows how the 32 bytes are allocated into 4 banks: 1. Microcontroller having inbuilt RAM or ROM and inbuilt timer. 2. Input and output ports are available. 3. Inbuilt serial port. 4. Separate memory to store program and data. 5. Many functions pins on the IC. 6. Boolean operation directly possible.

MPMC
7. It take few instructions to read and write data from external memory.

5.Compare microprocessor and microcontroller. Microprocessor 1. Do not have inbuilt RAM or ROM and timer. Microcontroller 1. Microcontroller having inbuilt RAM or ROM and inbuilt timer.

2. Input and output ports are not available, requires extra device like 8155 3. Do not have inbuilt serial port, requires 8250 device. 4. Program and data are stored in same memory. 5. Less multifunction pins on IC. 6. Boolean operation is not possible directly. 7. It take many instruction to read and write data from external memory.

2. Input and output ports are available. 3. Inbuilt serial port.

4. Separate memory to store program and data. 5. Many functions pins on the IC. 6. Boolean operation directly possible. 7. It take few instructions to read and write data from external memory.

MPMC
6.Explain single operand arithmetic instructions of8051microcontroller

7. Explain the internal RAM memory of 8051 microcontroller. RAM memory consists of 3 blocks containing 128 registers each. Its structure falls into the 8051 standard: 128 general-purpose registers; 128 memory locations reserved for SFRs. Even though only some of them are trully used, free locations shouldnt be used for storing variables; and 128 additional registers available for use (have no special purpose). Since they have the same addresses as SFRs, they are accessed by indirect addressing.

MPMC

8. Can you use DPTR to access internal ROM? Justify your answer. DPTR register is not a true one because it doesn't physically exist. It consists of two separate registers: DPH (Data Pointer High) and (Data Pointer Low). For this reason it may be treated as a 16-bit register or as two independent 8-bit registers. Their 16 bits are primarly used for external memory addressing. Besides, the DPTR Register is usually used for storing data and intermediate results.

9. Write an 8051 assembly language program to perform BCD addition of two 8 bit number data stored in location 51H and 52H and store the result in memory location 53H. MOV R1,#20 MOV R2,#30 MOV A,R1 ADD A,R2 DA R,A MOV R5,A HERE: SJMP HERE

MPMC

10. List and explain various data transfer instructions of 8051 microcontroller.

Anda mungkin juga menyukai