Anda di halaman 1dari 6

CONFIGURACION DE INTERFACES Y DHCP EN ROUTER Paso 1: configurar Interfaz en el cual se conecta Switch R1config)#interface FastEthernet0/0 R1(config-if)#ip address 1.1.1.

1 255.0.0.0 R1config-if)#no shutdown Paso 2: configurar Dhcp en Router cisco R1>enable R1#configure terminal R1(config)#ip dhcp pool Voz R1(dhcp-config)#network 1.0.0.0 255.0.0.0 R1(dhcp-config)#default-router 1.1.1.1 R1(dhcp-config)#option 150 ip 1.1.1.1 CONFIGURACION DE CALL MANAGER EXPRESS EN ROUTER Paso 1: configurar Interfaz CME R1(config)#telephony-service R1(config-telephony)#max-ephones 5 R1(config-telephony)#max-dn 5 R1(config-telephony)#ip source-address 1.1.1.1 port 2000 R1(config-telephony)#auto assign 4 to 6 R1config-telephony)#auto assign 1 to 5 CONFIGURACION DE LAS VLAN VOZ EN SWITCH Switch(config)#interface range fa0/1 5 Switch(config-if-range)#switchport mode acces Switch(config-if-range)#switchport voice vlan 1 Switch(config-if-range)#exit

Establece el Nmero de telefonos Establece el Nmero de Directorios Direccion de Puerta de enlace puesta en el interfaz del router

Configuracin para manejar paquetes de voz

PARA QUE EL TELEFONO IP TOME LA EXTENSION SE CONFIGURA EN ROUTER R1(config)#ephone-dn 1 Definir el nmero de IP de directorio N de telfono R1(config-ephone-dn)#number 1101 1101 Asignar el nmero # Asegrese de que este telfono IP recibe un 'Direccin IP' del servidor DHCP configurado en 'R1' y tambin una 'Nmero de lnea ". (Tenga en cuenta que esto puede tardar unos segundos). SI SE REQUIERE MAS TELEFONOS IP HACER EN ROUTER R1(config)#ephone-dn 1 Definir el nmero de IP de directorio N de telfono R1(config-ephone-dn)#number 1102 1101 Asignar el nmero #

CUANDO NO ES UN TELEFONO SINO UNA LAPTOCK O PC R1(config)#ephone-dn 1 R1(config-ephone-dn)#number 1103

CONFIGURACION DE LAS INTERFACES SERIAL DEL ROUTER DEFINIR CUAL ES EL DCE. CONFIGURACION ROUTER 1 R1(config)#interface serial 0/3/0 R1(config-if)#ip address 3.0.0.1 255.0.0.0 R1(config-if)#clockrate 56000 R1(config-if)#no shutdown CONFIGURACION ROUTER 2 R2(config)#interface serial 0/3/0 R2(config-if)#ip address 3.0.0.2 255.0.0.0 R2(config-if)#no shutdown CONFIGURAR OSPF R1(config)#router ospf 1 R1(config-router)#network 192.168.1.0 0.0.0.3 area 0 R1(config-router)#network 192.168.2.0 0.0.0.3 area 0 Se le asigna las ip que estan conectas directamente wildacar es la inversa de la mascara 255.255.255.0 0.0.0.255

CONFIGURAR EN LOS ROUTERS Dial Peer Mapping" Para que un telfono IP perteneciente a una LAN puede llamar a travs de la WAN a otro telfono IP R1(config)#dial-peer voice 1 voip R1(config-dial-peer)#destination-pattern 2 R1(config-dial-peer)#session target ipv4:3.0.0.2 R2(config)#dial-peer voice 1 voip R2(config-dial-peer)#destination-pattern 2 R2(config-dial-peer)#session target ipv4:3.0.0.2

Se debe de asignar la ip del Router del serial 2.

ENRUTAMIENTO ENTRE VLANS Cuando en un mismo switch hay vlan de voz y datos se requiere del router para que este las comunique La interfaz que conecta el router con el Switch se debe de esta blecer como troncal Switch(config)#interface fa0/1 Switch(config-if-range)#switchport mode trunk Switch(config-if-range)#exit

CREACION DE SUBINTERFACES EN ROUTER Segn la cantidad de Vlan se crea igual nmero de subinterfaces 1) Primero subir la interfaz sin nescesidad de asignar la ip Switch(config)#interface fa0/1 Switch(config-subif)#encapsulation dot1Q #VLAN Switch(config-subif)#ip address 192.168.0.1 255.255.255.0 Direccion con la cual va ha quedar la Vlan Switch(config-subif)#exit Switch(config)#interface fa0/1 Switch(config-if)#ino sh

e puesta en el interfaz del router

aquetes de voz

ectorio N de telfono

urado en 'R1' y tambin una

ectorio N de telfono

conectas directamente

otro telfono IP

outer del serial 2.

este las comunique

ter con el Switch se debe de esta

port mode trunk

Anda mungkin juga menyukai