Anda di halaman 1dari 8

a

FEATURES High CMRR: 100 dB Typ Low Nonlinearity: 0.001% Max Low Distortion: 0.001% Typ Wide Bandwidth: 3 MHz Typ Fast Slew Rate: 9.5 V/s Typ Fast Settling (0.01%): 1 s Typ Low Cost APPLICATIONS Summing Amplifiers Instrumentation Amplifiers Balanced Line Receivers Current-Voltage Conversion Absolute Value Amplifier 4 to 20 mA Current Transmitter Precision Voltage Reference Applications Lower Cost and Higher Speed Version of INA105

Precision, Unity-Gain Differential Amplifier AMP03


FUNCTIONAL BLOCK DIAGRAM
AMP03
IN 2 25k 25k 5 SENSE +VCC

OUTPUT VEE

4 25k 25k 1

+IN

REFERENCE

PIN CONNECTIONS 8-Lead PDIP (P Suffix)

GENERAL DESCRIPTION

The AMP03 is a monolithic unity-gain, high speed differential amplifier. Incorporating a matched thin film resistor network, the AMP03 features stable operation over temperature without requiring expensive external matched components. The AMP03 is a basic analog building block for differential amplifier and instrumentation applications. The differential amplifier topology of the AMP03 both amplifies the difference between two signals and provides extremely high rejection of the common-mode input voltage. By providing common-mode rejection (CMR) of 100 dB typical, the AMP03 solves common problems encountered in instrumentation design. As an example, the AMP03 is ideal for performing either addition or subtraction of two signals without using expensive externally matched precision resistors. The large common-mode rejection is made possible by matching the internal resistors to better than 0.002% and maintaining a thermally symmetric layout. Additionally, due to high CMR over frequency, the AMP03 is an ideal general amplifier for buffering signals in a noisy environment into data acquisition systems. The AMP03 is a higher speed alternative to the INA105. Featuring slew rates of 9.5 V/s and a bandwidth of 3 MHz, the AMP03 offers superior performance to the INA105 for high speed current sources, absolute value amplifiers, and summing amplifiers.

REFERENCE 1 IN 2

8 NC

7 V+ TOP VIEW (Not to Scale) 6 OUTPUT 3 +IN V 4 5 SENSE

AMP03

NC = NO CONNECT

8-Lead SOIC (S Suffix)


REFERENCE 1 IN 2 8 NC

7 V+ TOP VIEW (Not to Scale) 3 6 OUTPUT +IN V 4 5 SENSE

AMP03

NC = NO CONNECT

Header (J Suffix)
NC 8 REFERENCE 1 7 V+

IN 2

6 OUTPUT 5 SENSE 4 V NC = NO CONNECT

+IN 3

REV. F
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 2003 Analog Devices, Inc. All rights reserved.

AMP03SPECIFICATIONS
ELECTRICAL CHARACTERISTICS (@ V = 15 V, T = +25C, unless otherwise noted.)
S A

Parameter Offset Voltage Gain Error Input Voltage Range Common-Mode Rejection Power Supply Rejection Ratio Output Swing Short-Circuit Current Limit Small-Signal Bandwidth (3 dB) Slew Rate Capacitive Load Drive Capability Supply Current

Symbol Conditions VOS VCM = 0 V No Load, VIN = 10 V, RS = 0 (Note 1) VCM = 10 V VS = 6 V to 18 V RL = 2 k Output Shorted to Ground RL = 2 k RL = 2 k No Oscillation No Load

Min 400

AMP03F Typ Max +10

Min

AMP03B AMP03G Typ Max Min Typ Max +20 +700 750 +25

Unit

+400 700

+750 V

0.00004 0.008 20 85 12 +45/15 6 3 9.5 300 2.5 100 0.6 13.7 20 80 10 12 +45/15 6

0.00004 0.008 95 0.6 13.7 20 80 10 12 +45/15 3 9.5 300 2.5 6

IVR CMR PSRR VO ISC BW SR CL ISY

0.001 0.008 % V 95 dB 0.7 10 V/V 13.7 V mA MHz V/s pF mA

3 9.5 300 2.5

3.5

3.5

3.5

NOTES 1 Input voltage range guaranteed by CMR test. Specifications subject to change without notice.

ELECTRICAL CHARACTERISTICS (@ V = 15 V, 55C T +125C for B Grade)


S A

Parameter Offset Voltage Gain Error Input Voltage Range Common-Mode Rejection Power Supply Rejection Ratio Output Swing Slew Rate Supply Current

Symbol VOS IVR CMR PSRR VO SR ISY

Conditions VCM = 0 V No Load, VIN = 10 V, RS = 0 VCM = 10 V VS = 6 V to 18 V RL = 2 k RL = 2 k No Load

Min 1500 20 75

AMP03B Typ +150 0.0014 95 0.7 13.7 9.5 3.0

Max +1500 0.02

Unit V % V dB V/V V V/s mA

20

12

4.0

Specifications subject to change without notice.

ELECTRICAL CHARACTERISTICS (@ V = 15 V, 40C T +85C for F and G Grades)


S A

Parameter Offset Voltage Gain Error Input Voltage Range Common-Mode Rejection Power Supply Rejection Ratio Output Swing Slew Rate Supply Current

Symbol VOS IVR CMR PSRR VO SR ISY

Conditions VCM = 0 V No Load, VIN = 10 V, RS = 0 VCM = 10 V VS = 6 V to 18 V RL = 2 k RL = 2 k No Load

Min

AMP03F Typ Max

Min

AMP03G Typ Max

Unit

1000 +100 +1000 0.0008 0.015 20 80 95 0.7 13.7 9.5 2.6 15

2000 +200 0.002 20 75 90 1.0 13.7 9.5 2.6

+2000 V 0.02 % V dB 15 V/V V V/s mA

12

12 4.0

4.0

Specifications subject to change without notice.

REV. F

AMP03 WAFER TEST LIMITS (@ V = 15 V, T = 25C, unless otherwise noted.)*


S A

Parameter Offset Voltage Gain Error Input Voltage Range Common-Mode Rejection Power Supply Rejection Ratio Output Swing Short-Circuit Current Limit Supply Current

Symbol VOS IVR CMR PSRR VO ISC ISY

Conditions VS = 18 V No Load, VIN = 10 V, RS = 0 VCM = 10 V VS = 6 V to 18 V RL = 2 k Output Shorted to Ground No Load

AMP03GBC Limit 0.5 0.008 10 80 8 12 +45/15 3.5

Unit mV max % max V min dB min V/V max V max mA min mA max

*Electrical tests are performed at wafer probe to the limits shown. Due to variations in assembly methods and normal yield loss, yield after packaging is not guaranteed for standard product dice. Consult factory to negotiate specifications based on dice lot qualifications through sample lot assembly and testing.

ABSOLUTE MAXIMUM RATINGS 1

DICE CHARACTERISTICS

Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V Input Voltage2 . . . . . . . . . . . . . . . . . . . . . . . . . Supply Voltage Output Short-Circuit Duration . . . . . . . . . . . . . . Continuous Storage Temperature Range P, J Package . . . . . . . . . . . . . . . . . . . . . . . 65C to +150C Lead Temperature (Soldering, 60 sec) . . . . . . . . . . . . 300C Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . 150C Operating Temperature Range AMP03B . . . . . . . . . . . . . . . . . . . . . . . . . 55C to +125C AMP03F, AMP03G . . . . . . . . . . . . . . . . . . 40C to +85C Package Type Header (J) 8-Lead PDIP (P) 8-Lead SOIC (S) JA3 150 103 155 JC 18 43 40 Unit C/W C/W C/W

1. 2. 3. 4. 5. 6. 7. 8.

REFERENCE IN +IN VEE SENSE OUTPUT +VCC NC

DIE SIZE 0.076 inch 0.076 inch, 5,776 sq. mm (1.93 mm 1.93 mm, 3.73 sq. mm)

NOTES 1 Absolute maximum ratings apply to both DICE and packaged parts, unless otherwise noted. 2 For supply voltages less than 18 V, the absolute maximum input voltage is equal to the supply voltage. 3 JA is specified for worst-case mounting conditions, i.e., JA is specified for device in socket for header and PDIP packages and for device soldered to printed circuit board for SOIC package.

BURN-IN CIRCUIT
+18V

25k

AMP03

ORDERING GUIDE
Model1 AMP03GP AMP03BJ AMP03FJ AMP03BJ/883C AMP03GS AMP03GS-REEL 5962-9563901MGA AMP03GBC Temperature Range 40C to +85C 40C to +85C 40C to +85C 55C to +125C 40C to +85C 40C to +85C 55C to +125C Package Description 8-Lead PDIP Header Header Header 8-Lead SOIC 8-Lead SOIC Header Die Package Option2 P-8 H-08B H-08B H-08B S-8 S-8 H-08B

25k

25k

18V

SLEW RATE TEST CIRCUIT


+15V 0.1F

AMP03

VOUT = 10V VIN = 10V 0.1F 15V

NOTES 1 Burn-in is available on commercial and industrial temperature range parts in PDIP and header packages. 2 Consult factory for /883 data sheet.

CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AMP03 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality.

WARNING!
ESD SENSITIVE DEVICE

REV. F

AMP03Typical Performance Characteristics


120 110

COMMON-MODE REJECTION (dB)

100 90 80

TA = +25C VS = 15V

0.1 TA = +25C VS = 15V AV = 1 0.010

THD+N (%)

70 60 50 40 30 20 10 0 1 10 100 1k 10k FREQUENCY (Hz) 100k 1M

RL = 600

0.001 RL = 100k

0.0001 20

100 1k FREQUENCY (Hz)

10k 20k

TPC 1. Small Signal Transient Response

TPC 2. Common-Mode Rejection vs. Frequency

TPC 3. Total Harmonic Distortion vs. Frequency

120

POWER SUPPLY REJECTION (dB)

110 100 90 80 70 60 50 40 30 20 10 0 1 10

TA = +25C VS = 15V

0.1

TA = +25C VS = 15V AV = 1

PSRR

0.010

DIM (%)

RL = 600, 100k 0.001

+PSRR

100 1k 10k FREQUENCY (Hz)

100k

1M

0.0001 2k

10k FREQUENCY (Hz)

50k

TPC 4. Large Signal Transient Response

TPC 5. Power Supply Rejection vs. Frequency

TPC 6. Dynamic Intermodulation Distortion vs. Frequency

1000 800 INPUT OFFSET VOLTAGE (V)

VS = 15V

50 40
CLOSED-LOOP GAIN (dB)

10

TA = +25C VS = 15V

TA = +25C VS = 15V 8

600 400 200 0 200 400 600 800 75 50 25 0 25 50 75 100 125 150 TEMPERATURE (C)

30 20 10 0 10 20 30 100

OUTPUT IMPEDANCE ()

1k

10k 100k FREQUENCY (Hz)

1M

10M

100

1k

10k 100k FREQUENCY (Hz)

1M

TPC 7. Input Offset Voltage vs. Temperature

TPC 8. Closed-Loop Gain vs. Frequency

TPC 9. Closed-Loop Output Impedance vs. Frequency

REV. F

AMP03
0.003 VS = 15V RS = 0

13 12 11 10 9 8 7 6 75 50 25 0 25 50 75 TEMPERATURE (C) VS = 15V RL = 2k

6 VS = 15V 5

0.002 0.001

SUPPLY CURRENT (mA)


100 125

SLEW RATE (V/s)

GAIN ERROR (%)

0.000 0.001

3 2

0.002 0.003 75 50 25

1 0 75 50 25

0 25 50 75 100 125 150 TEMPERATURE (C)

0 25 50 75 100 125 150 TEMPERATURE (C)

TPC 10. Gain Error vs. Temperature

TPC 11. Slew Rate vs. Temperature

TPC 12. Supply Current vs. Temperature


17.5

4 TA = +25C

17.5
MAXIMUM OUTPUT VOLTAGE (V)

MAXIMUM OUTPUT VOLTAGE (V)

15.0 12.5 10.0 7.5 5.0 2.5 0 0

VS = 18V VS = 15V

TA = +25C

15.0 12.5 10.0 7.5 5.0 2.5 0

VS = 18V VS = 15V VS = 12V VS = 9V

SUPPLY CURRENT (mA)

VS = 12V VS = 9V

VS = 5V

VS = 5V TA = +25C

0 0

5 10 15 SUPPLY VOLTAGE (V)

20

6 12 18 24 30 OUTPUT SOURCE CURRENT (mA)

36

2 4 6 10 8 OUTPUT SINK CURRENT (mA)

12

TPC 13. Supply Current vs. Supply Voltage


120
VOLTAGE NOISE DENSITY (nV/ Hz)

TPC 14. Maximum Output Voltage vs. Output Current (Source)

TPC 15. Maximum Output Voltage vs. Output Current (Sink)

TA = +25C VS = 15V

100

80 +1V 60 0V 1V 40

+10V 0V 10V

20 0 1 10 100 1k FREQUENCY (Hz) 10k

0.1 TO 10Hz PEAK-TO-PEAK NOISE

NOTE: EXTERNAL AMPLIFIER GAIN = 1000; THEREFORE, VERTICAL SCALE = 10V/DIV.

TPC 16. Voltage Noise Density vs. Frequency

TPC 17. Low Frequency Voltage Noise

TPC 18. Voltage Noise from 0 kHz to 1 kHz

+10V 0V 10V

NOTE: EXTERNAL AMPLIFIER GAIN = 1000; THEREFORE, VERTICAL SCALE = 10V/DIV.

TPC 19. Voltage Noise from 0 kHz to 10 kHz

REV. F

AMP03
+V 0.1F (GROUND REFERENCE 2) AMP03 VSIGNAL V 0.1F VOUT = VSIGNAL

APPLICATIONS INFORMATION

The AMP03 represents a versatile analog building block. In order to capitalize on the fast settling time, high slew rate, and high CMR, proper decoupling and grounding techniques must be employed. Figure 1 illustrates the use of 0.1 F decoupling capacitors and proper ground connections.
MAINTAINING COMMON-MODE REJECTION

ECM

GROUND REFERENCE 1

GROUND REFERENCE 2

Figure 1. AMP03 Serves to Reject Common-Mode Voltages in Instrumentation Systems. Common-Mode Voltages Occur Due to Ground Current Returns. VSIGNAL and ECM Must Be within the Common-Mode Range of AMP03.

In order to achieve the full common-mode rejection capability of the AMP03, the source impedance must be carefully controlled. Slight imbalances of the source resistance will result in a degradation of dc CMReven a 5 imbalance will degrade CMR by 20 dB. Also, the matching of the reactive source impedance must be matched in order to preserve the CMRR over frequency.

APPLICATION CIRCUITS
+15V 0.1F

AMP03
IN E1 R1 25k R2 25k

REF10
+5V OUT

E0 = E2 E1 +IN E2

AMP03
5V OUT

R3 25k

R4 25k

Figure 2. Precision Difference Amplifier. Rejects Common-Mode Signal = (E1 + E2)/2 by 100 dB Figure 5. 5 V Precision Voltage Reference
AMP03
E1 E0 = E1

AMP03

E1 E2

E0 = E1 + E2

Figure 3. Precision Unity-Gain Inverting Amplifier Figure 6. Precision Summing Amplifier


+15V 0.1F +10V OUT
R1 R2

REF10

AMP03
10V OUT

AMP03
E = E2 E0 = (R2/R1+1) 1 2

E1 E2

Figure 4. 10 V Precision Voltage Reference

Figure 7. Precision Summing Amplifier with Gain

REV. F

AMP03
AMP03
E2

System Design Requirement Source Impedance Low, Need Low Voltage Noise Performance

Suggested Op Amp For A1 and A2 OP27, OP37 OP227 (Dual Matched) OP270 (Dual) OP271 OP470 OP471 OP80 OP41 OP43 OP249 OP97 OP80 OP97 OP41 OP43 OP42 OP43 OP249

R E1 OP80EJ I 0 = (E1 E2 )/R I0 LOAD

Figure 8. Differential Input Voltage-to-Current Converter for Low IOUT. OP80EJ maintains 250 fA max input current, allowing IO to be less than 1 pA.
IN E1

Source Impedance High (RS 15 k). Need Low Current Noise

AMP03
A1 R2 R1 R2 E0 OUTPUT

Require Ultrahigh Input Impedance

A2 +IN E2 E0 = (1 + 2R2/R1) (E2 E1)

Need Wider Bandwidth and High Speed

Figure 9. Suitable Instrumentation Amplifier Requirements Can Be Addressed by Using an Input Stage Consisting of A1, A2, R1, and R2. The following matrix suggests a suitable amplifier.

REV. F

AMP03
OUTLINE DIMENSIONS 8-Lead Small Outline Package [SOIC] [S Suffix] (R-8)
Dimensions shown in millimeters and (inches)
5.00 (0.1968) 4.80 (0.1890)
8 5 4

8-Lead Plastic Dual In-Line Package [PDIP] [P Suffix] (N-8)


Dimensions shown in inches and (millimeters)
0.375 (9.53) 0.365 (9.27) 0.355 (9.02)
8 5

0.295 (7.49) 0.285 (7.24) 0.275 (6.98) 0.325 (8.26) 0.310 (7.87) 0.300 (7.62) 0.015 (0.38) MIN SEATING PLANE 0.060 (1.52) 0.050 (1.27) 0.045 (1.14)

4.00 (0.1574) 3.80 (0.1497)

6.20 (0.2440) 5.80 (0.2284)

0.100 (2.54) BSC 0.180 (4.57) MAX 0.150 (3.81) 0.130 (3.30) 0.110 (2.79) 0.022 (0.56) 0.018 (0.46) 0.014 (0.36)

0.150 (3.81) 0.135 (3.43) 0.120 (3.05)

1.27 (0.0500) BSC 0.25 (0.0098) 0.10 (0.0040) COPLANARITY SEATING 0.10 PLANE

1.75 (0.0688) 1.35 (0.0532)

0.50 (0.0196) 45 0.25 (0.0099)

0.51 (0.0201) 0.31 (0.0122)

0.015 (0.38) 0.010 (0.25) 0.008 (0.20)

8 0.25 (0.0098) 0 1.27 (0.0500) 0.40 (0.0157) 0.17 (0.0067)

COMPLIANT TO JEDEC STANDARDS MS-012AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN

COMPLIANT TO JEDEC STANDARDS MO-095AA CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN

8-Lead Metal Can [TO-99] [J Suffix] (H-08B)


Dimensions shown in inches and (millimeters)
REFERENCE PLANE 0.1850 (4.70) 0.1650 (4.19) 0.5000 (12.70) MIN 0.2500 (6.35) MIN 0.0500 (1.27) MAX 5
0.3700 (9.40) 0.3350 (8.51) 0.3350 (8.51) 0.3050 (7.75)

0.1000 (2.54) BSC

0.1600 (4.06) 0.1400 (3.56) 0.0450 (1.14) 0.0270 (0.69)

4 0.2000 (5.08) BSC 0.1000 (2.54) BSC 3 2 0.0190 (0.48) 0.0160 (0.41) 0.0210 (0.53) 0.0160 (0.41) BASE & SEATING PLANE 1

6 7 8

0.0400 (1.02) MAX 0.0400 (1.02) 0.0100 (0.25)

0.0340 (0.86) 0.0280 (0.71) 45 BSC

COMPLIANT TO JEDEC STANDARDS MO-002AK CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETERS DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN

Revision History
Location 12/03Data Sheet changed from REV. E to REV. F. Page

Changes to ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Changes to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 8 REV. F

C00249012/03(F)

Anda mungkin juga menyukai