HM 230 Eco V
Atlas Copco Construction Tools GmbH P. O. Box 102152, 45021 Essen Helenenstrasse 149, 45143 Essen Federal Republic of Germany Telefon +49 201 633 0 Telefax +49 201 633 2281 Telefax Customer Support +49 201 633 1352
Table of contents
1. 2. 3. Working tools for HM 230 Eco V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Main dimensions and weight HM 230 Eco V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Percussion unit HM 230 Eco V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1. 3.2. Presentation percussion unit HM 230 Eco V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Spare parts list percussion unit HM 230 Eco V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 7 8
8 9
4.
10
10 11
5.
Hydraulic hammer HM 230 Eco V (with standard adapter and adapter kit) . . . . . . .
5.1. 5.2. Presentation hydraulic hammer HM 230 Eco V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parts List Adapter kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
12 13
Instructions of ordering
Please note the full identification number of your HM 230 Eco V. This code can be found on the cylinder ( part no.20 ) Determine the quantity of individual parts which are required and need to be ordered. The order must indicate the following details: H full identification code of the HM 230 Eco V H required quantity H part ident. no. H designation
4 Tensioning bolts Part ident. no. 3363 0840 03 Important: Please indicate the address to which the parts should be sent and the type of shipment required.
Description Useful length [ mm ] Weight [ kg ] Part ident. no. Standard designs: Moil point 80 415 27,5 3363 0678 29
1.
415
27,8
3363 0690 19
Spade transverse
Further special designs available on request. Please note: Working tools will be subject to wear in the normal course of operations. Chisel paste for ContiLube II, part ident. no. 3363 0660 65 Manual grease gun for Krupp chisel paste, 6 part ident. no. 3363 0345 67
160
405
35,0
3363 0690 23
2.
205 60
35
260 22 415
1102 210
248
80
160 50
80
260
340 390
25
Weight: . . . . . . 319 kg (as shown, with hammer box, without chisel and without adapter)
3.
3.1.
13 16 15 14
13
19
17 18 17 27 22
17 18
21 4
cylinderno. serialno.
21
30
21
23, 26 25 28 20 28 29 29, 30 31 33 36 32 24 34 35 4 30 29 31
3.2.
Part No.
1 2 3 4 5 6 7 8 9K 10 11 12 K 13 K 14 15 K 16 K 17 K 18 K 19 K 20 21 K 22 K 23 24 25 K 26 27 28 K 29 K 30 K 31 K 32 33 K 34 K 35 K 36 K 37 38 39 40 K
3363 0840 03 3360 4801 95 3360 4354 30 3360 1067 44 3363 0317 12 3363 0840 05 3363 0851 94 3363 0872 86 3360 1751 25 3363 0702 99 3363 0669 63 3362 2674 32 3363 0874 34 3363 0859 22 3361 0315 47 3363 0708 19 3363 0665 13 3363 0669 60 3363 0667 18 3363 0840 11 3362 2675 81 3363 0835 73 3361 0314 76 3361 0835 74 3360 4781 71 3361 3534 86 3363 0840 13 3363 0665 84 3363 0665 85 3363 0665 14 3363 0665 87 3363 0840 15 3363 0846 69 3363 0840 17 3361 0314 62 3362 2675 82 3360 2065 96 3360 4784 26 3360 1078 79 3363 0859 23 3363 0837 79
When ordering spare parts please do not forget to state the tool ident. no. 9
4.
4.1.
1 150 101
201
106
114, 115
10
4.2.
Part No.
3363 0851 58
3363 0840 01
Parts marked with K will be subject to wear in the normal course of operations. When ordering spare parts please do not forget to state the tool ident. no. Note: When a hammer box assembly is ordered, a loose CE nameplate is included in the consignment in accord ance with European CE legislation. The weight stated on the adhesive nameplate refers to the weight of the hydraulic hammer plus hammer box (not including connector and tool). After the hydraulic hammer and the hammer box have been assembled the CE nameplate should be attached to rear of the hammer box (see Section 3 of the operating manual). Only then may the complete unit be used. 11
5.
5.1.
Hydraulic hammer HM 230 Eco V (with standard adapter and adapter kit)
Presentation hydraulic hammer HM 230 Eco V
Parts nos. see adapter kit
916
12
5.2.
Quantity 2 1 2 2 1 2
Description Bearing bush Pin Cotter pin Bearing bush Pin Spring dowel sleeve
For the majority of carriers, the standard hammer adapter incl. adapter kit can be used. Different adapter kits are designed for use with different carrier types, taking into account variations in pin diameter and stick and toggle width. If stick and toggle are of nonstandard size, it is only possible to attach the hammer using a speciallydesigned adapter. In such cases, please contact our customer support.
13
Notes:
14
15
Atlas Copco Construction Tools GmbH Helenenstrasse 149 S 45143 Essen P. O. Box 10 21 52 S 45021 Essen Federal Republic of Germany Telephone +49 201 633 0 Telefax +49 201 633 2281 Telefax Customers Support +49 201 633 1352 Internet: www.hydraulicattachments.com
Your partner: