C-48
C705.03 Test Report Evaluations and Distributions. Concrete strength, slump, air, and other physical properties are reported on forms LB-11 and LB-59, which are distributed as follows: (1) (1) (1) (1) District Construction Engineer Lab Contract main file Plant file Source of Material (only sampled material test results)
Physical properties of the concrete materials are recorded on form LB-7, which is distributed as follows: (1) copy (1) copy (1) copy District Construction Engineer/ District Engineer (for random test result of material sampled at the site) Lab Contract main office Source of material (test results of material sampled at quarry or stockpiles)
C-49
Castings for Department projects must be approved prior to use. Acceptance is on the basis of manufacturers certification and visual inspection either at the foundry or the contractors yard.
C708.02 Tests Performed. Portland cement concrete used in the construction of drainage inlets must conform to the requirements of Class B concrete. The concrete is tested for strength, slump, and other material characteristics. Bar reinforcement is certified by mill analysis of each size and heat from each production mill. Castings are required to meet the following requirements. Castings, gratings, manholes and steps must conform to the material specifications listed in Table C-30. Prior to the initial shipment of cast iron material, the Department will conduct an inspection of the foundry supplying castings for Department projects. This inspection includes all foundry facilities and work in progress. If the foundry is acceptable, no additional inspections will be made. However, the Department reserves the right to visit the foundry on a random basis. In addition to the inspection, the foundry must provide the Materials & Research Section with three copies of certifications or test results for each heat from which the material is supplied. The certifications or test results shall indicate that the supplied materials conform to the Specifications. The Materials & Research Section must be notified when castings are ready to ship so that the castings may be inspected. Castings from local foundries will be inspected at the foundry. Castings from out of state suppliers will be inspected at the contractors yard unless circumstances require otherwise. Upon passing inspection, castings will be stenciled with the standard Department of Highways stencil. C708.03 Test Report Evaluations and Distributions. Physical properties of concrete are recorded on form LB-7, which is distributed as follows: (1) copy (2) copies Lab main file District Construction Engineer
Mill analysis reports for bar reinforcement and certification of casting gratings are distributed as follows: (1) copy (2) copies Central Lab Contract File District Construction Engineer
Inspection reports for gratings (Form LB-100) and copies of material certifications or test results are distributed as follows: (2) copies (1) copy District Construction Engineer Lab Main Contract File
C-50
C-51
Stone used in underdrain construction must conform to the requirements for Delaware No. 8 stone or Delaware No. 57 stone, depending on contract requirements. It is verified by gradation testing. C715.03 Test Report Evaluations and Distributions. Visual inspection reports, form LB-100, and certifications are distributed as follows: (1) copy (2) copies Contract file Construction Engineer
C-52
C-53
C-54
C744.03 Test Report Evaluations and Distributions. Material certifications and testing results are distributed as follows: (2) copies (1) copy District Construction Engineer Lab Main Contract File
C-55
mix, described in detail in Section 823 of the Standard Specifications. In addition to meeting the requirements for Type D hot mix, 0.25 to 0.50% of the total mix weight of a synthetic fiber must be added. C755.02 Test Report Evaluations and Distributions. Material certifications are distributed as follows: (2) copies (1) copy District Construction Engineer Lab Main Contract File
C-56
Table C-27: Division 700 - Sampling Methods Method Name Sampling Soil and Aggregate Base Sampling Stone, Slag, Gravel, Sand, and Sand Block for Use as DOH 5 Highway Materials DOH 10 Sampling Fresh Portland Cement Concrete ASTM C172-90 Practice for Sampling Freshly Mixed Concrete Method ID DOH 3 Table C-28: Division 700 - Sample Identification Numbering Pipe Sample Ids include the type of pipe inspected, the number of the inspection in order from the first date of pipe inspection, and the year the inspection occurred. The ID is P-No.-Year. Brick and Cement Block Ids include the number of the inspection in order from the first date of the pipe inspection and the year the inspection occurred. The ID is K-No. -Year for Brick and NNo.-Year for Cement Block Coarse aggregate samples start with Test # 1 on January 1 and are numbered consecutively until December 31. Example: D-1-02 D = Delaware , 1 = test number, 02 = Year 2002 Fine aggregate samples are numbered consecutively from the start of the fiscal year, July 1, until June 30 the following year Concrete Cylinders are numbered consecutively from the beginning of testing at this laboratory, the Sample Identification is E#######, where the # sign represents the number of the test
C-57
Test ID DOH 9 ASTM C39 ASTM C127 ASTM C501 ASTM D395 ASTM D638 ASTM D2240 ASTM D4061 ASTM E303 AASHTO T11 AASHTO T19 AASHTO T21 AASHTO T22 AASHTO T23 AASHTO T24 AASHTO T26 AASHTO T27 AASHTO T65 AASHTO T85 AASHTO T88 AASHTO T89 AASHTO T90 AASHTO T96 AASHTO T119 AASHTO T152 AASHTO T194 AASHTO T196 AASHTO T199 AASHTO T309 AASHTO T250 Fed. Test #141
Table C-29: Division 700 - Test Methods Test Name pH of Soil and Topsoil Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens Standard Test Method for Density, Relative Density (Specific Gravity), and Absorption of Coarse Aggregate Standard Test Method for Relative Resistance to Wear of Unglazed Ceramic Tile by the Taber Abraser Standard Test Methods for Rubber Property - Compression Set Standard Test Method for Tensile Properties of Plastics Standard Test Method for Rubber Property - Durometer Hardness Standard Test Method for Retroreflectance of Horizontal Coatings Standard Test Method for Measuring Surface Frictional Properties Using the British Pendulum Tester Materials Finer Than 75-m (No.200) Sieve in Mineral Aggregates by Washing Bulk Density ("Unit Weight") and Voids in Aggregate Organic Impurities in Fine Aggregates for Concrete Compressive Strength of Cylindrical Concrete Specimens Making and Curing Concrete Test Specimens in the Field Obtaining and Testing Drilled Cores and Sawed Beams of Concrete Quality of Water to be Used in Concrete Sieve Analysis of Fine and Coarse Aggregates Mass (Weight) of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings Specific Gravity and Absorption of Coarse Aggregate Particle Size Analysis of Soils Determining the Liquid Limit of Soils Determining the Plastic Limit and Plasticity Index of Soils Resistance to degradation of Small Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine Slump of Hydraulic Cement Concrete Air Content of Freshly Mixed Concrete by the Pressure Method Determination of Organic Matter in Soils by Wet Combustion Air Content of Freshly Mixed Concrete by the Volumetric Method Air Content of Freshly Mixed Concrete by the Chace Indicator Temperature of Freshly Mixed Portland Cement Concrete Thermoplastic Traffic Line Material Test for Reflectance Relative to a Magnesium Oxide Standard
C-58
Table C-30: Division 700 - Certification Test Procedures / Material Standards Test ID Test Name ASTM A36 Standard Specification for Carbon Structural Steel ASTM A48 Standard Specification for Gray Iron Castings Standard Specification for Pipe, Steel, Black and Hot-Dipped, ZincASTM A53 Coated, Welded and Seamless Standard Specification for Metallic-Coated, Steel Woven Wire Fence ASTM A116 Fabric Standard Specification for Zinc-Coated (Galvanized) Steel Barbed ASTM A121 Wire Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on ASTM A123 Iron and Steel Products Standard Specification for Steel Welded Wire Reinforcement, Plain, ASTM A185 for Concrete Standard Practices for Detecting Susceptibility to Intergranular Attack ASTM A262 in Austenitic Stainless Steels Standard Specification for Carbon Steel Bolts and Studs, 60 000 PSI ASTM A307 Tensile Strength Standard Specification for Structural Bolts, Steel, Heat Treated, ASTM A325 120/105 ksi Minimum Tensile Strength Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) by ASTM A446 the Hot-Dip Process, Structural Physical Quality Standard Specification for Chromium-Nickel Stainless Steel Weaving ASTM A478 and Knitting Wire Standard Specification for Stainless Steel Bars and Shapes for Use in ASTM A479 Boilers and Other Pressure Vessels Standard Specification for Steel Welded Wire Reinforcement, ASTM A497 Deformed, for Concrete Standard Specification for Cold-Formed Welded and Seamless ASTM A500 Carbon Steel Structural Tubing in Rounds and Shapes ASTM A536 Standard Specification for Ductile Iron Castings Standard Specification for Structural Steel, Sheet and Strip, Carbon, ASTM A570 Hot-Rolled Standard Specification for Aluminum-Coated Steel Woven Wire ASTM A584 Fence Fabric Standard Specification for High-Strength Low-Alloy Structural Steel ASTM A588 with 50 ksi [345 MPa] Minimum Yield Point to 4-in. [100 mm] Thick Standard Specification for Deformed and Plain Billet-Steel Bars for ASTM A615 Concrete Reinforcement Standard Specification for Carbon and High-Strength Electric ASTM A769 Resistance Welded Steel Structural Shapes Standard Specification for Aluminum and Aluminum-Alloy Sheet and ASTM B209 Plate
C-59
Table C-30 (cont.): Division 700 - Certification Test Procedures / Material Standards Test ID Test Name Standard Specification for Aluminum and Aluminum-Alloy Extruded ASTM B221 Bars, Rods, Wire, Profiles, and Tubes Standard Specification for Concrete Masonry Units for Construction of ASTM C139 Catch Basins and Manholes ASTM D1535 Standard Practice for Specifying Color by the Munsell System ASTM D1777 Standard Test Method for Thickness of Textile Materials Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, ASTM D1785 Schedules 40, 80, and 120 Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) ASTM D3034 Sewer Pipe and Fittings Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) ASTM D3035 Based on Controlled Outside Diameter ASTM D3776 Standard Test Methods for Mass Per Unit Area (Weight) of Fabric Standard Test Method for Hydraulic Bursting Strength of Textile ASTM D3786 Fabrics-Diaphragm Bursting Strength Tester Method Standard Specification for Polypropylene Injection and Extrusion ASTM D4101 Materials Standard Test Method for Deterioration of Geotextiles from Exposure ASTM D4355 to Ultraviolet Light and Water (Xenon-Arc Type Apparatus) Standard Test Methods for Water Permeability of Geotextiles by ASTM D4491 Permittivity ASTM D4533 Standard Test Method for Trapezoid Tearing Strength of Geotextiles Standard Test Method for Tensile Properties of Geotextiles by the ASTM D4595 Wide-Width Strip Method Standard Test Method for Grab Breaking Load and Elongation of ASTM D4632 Geotextiles Standard Test Method for Determining Apparent Opening Size of a ASTM D4751 Geotextile Standard Test Method for Breaking Force and Elongation of Textile ASTM D5035 Fabrics (Strip Method) ASTM D5621 Standard Test Method for Sonic Shear Stability of Hydraulic Fluid Standard Specification for Carbon and Alloy Steel Externally Threaded ASTM F568 Metric Fasteners AASHTO M31 Deformed and Plain Billet-Steel Bars for Concrete Reinforcement AASHTO M36 Corrugated Steel Pipe, Metallic-Coated, for Sewers and Drains AASHTO M85 Portland Cement AASHTO M105 Gray Iron Castings AASHTO M111 Sinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products AASHTO M114 Building Brick (Solid Masonry Units Made from Clay or Shale) AASHTO M133 Preservatives and Pressure Treatment Processes for Timber
C-60
Table C-30 (cont.): Division 700 - Certification Test Procedures / Material Standards Test ID Test Name AASHTO M168 Wood Products AASHTO M180 Corrugated Sheet Steel Beams for Highway Guardrail AASHTO M181 Chain-Link Fence AASHTO M183 Standard Specification for Structural Steel AASHTO M232 Zinc Coating (Hot-Dip) on Iron and Steel Hardware AASHTO M247 Glass Beads Used in Traffic Paints AASHTO M248 Ready Mixed White and Yellow Traffic Paints White and Yellow Reflective Thermoplastic Striping Material (Solid AASHTO M249 Form) AASHTO M268 Retroreflective Sheeting for Traffic Control Carbon and High-Strength Low-Alloy Structural Steel Shapes, Plates, and AASHTO M270 Bars and Quenched-and-Tempered Alloy Structural Steel Plates for Bridges AASHTO M279 Zinc-Coated (Galvanized) Steel Woven Wire Fence Fabric AASHTO M280 Zinc-Coated (Galvanized) Steel Barbed Wire AASHTO M281 Steel Fence Posts and Assemblies, Hot-Wrought AASHTO M284 Epoxy-Coated Reinforcing Bars: Materials and Coating Requirements AASHTO M285 Castings, Iron-Chromium-Nickel, Corrosion Resistant, for Sever Service AASHTO M288 Geotextile Specification for Highway Applications AASHTO M294 Corrugated Polyethylene Pipe, 300 to 1200 mm Diameter AASHTO M298 Coatings of Zinc Mechanically Deposited on Iron and Steel AASHTO M300 Inorganic Zinc-Rich Primer AASHTO T250 Thermoplastic Traffic Line Material AISI 201 Stainless Steel Alloy Standards AISI 301 Stainless Steel Alloy Standards AISI 302 Stainless Steel Alloy Standards AISI 316 Modified Annealed Cold Finish Standards ANSI C80.1 Specification for Rigid Steel Conduit, Zinc Coated (GRC) ANSI/AITC American National Standard - Structural Glued Laminated Timber A190.1 Production Requirements for Glulam VA DOT VTM51 Filtering Efficiency and Flow Rate of a Filter Fabric
C-61