06/27/11
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours) Issue Date: 06/27/11 Supercedes Date: 06/24/09 Document Group: 11-2425-4 Product Use: Intended Use: Specific Use:
SECTION 2: INGREDIENTS
Ingredient
ACETONE BUTANE XYLENE METHYL ETHYL KETONE STYRENATED ALKYD RESIN PROPANE ETHYL 3-ETHOXYPROPIONATE
C.A.S. No.
67-64-1 106-97-8 1330-20-7 78-93-3 68604-18-2 74-98-6 763-69-9
% by Wt
25 10 15 10 10 10 <5 30 20 20 15 15 15
Minute quantities of the substances listed below may be emitted during Normal Use: Substance Hydrocarbons Ketones Condition Normal Use Normal Use
MATERIAL SAFETY DATA SHEET Scotch Electrical Insulating Sealer 1601, Clear
06/27/11
Specific Physical Form: Aerosol Odor, Color, Grade: clear, solvent odor General Physical Form: Liquid Immediate health, physical, and environmental hazards: Flammable liquefied gas. Aerosol container contains flammable gas under pressure. Closed containers exposed to heat from fire may build pressure and explode. Extremely flammable liquid and vapor. Vapors may travel long distances along the ground or floor to an ignition source and flash back. Aerosol container contains flammable material under pressure. May cause target organ effects.
_________________________________________________________________________________________________ Page 2 of 9
MATERIAL SAFETY DATA SHEET Scotch Electrical Insulating Sealer 1601, Clear
06/27/11
_________________________________________________________________________________________________ Page 3 of 9
MATERIAL SAFETY DATA SHEET Scotch Electrical Insulating Sealer 1601, Clear
06/27/11
lined with polyethylene plastic or contain a plastic drum liner made of polyethylene. Dispose of collected material as soon as possible. Clean-up methods Contain spill, using absorbent if necessary. Collect spilled material with non-sparking tools. Clean up residue. Place depressurized cans and clean up wastes in a metal container approved for transportation. Seal the container. Refer to other sections of this MSDS for information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment. Call 3MHELPS line (1-800-364-3577) for more information on handling and managing the spill. Contain spill. Cover spill area with a fireextinguishing foam designed for use on solvents, such as alcohols and acetone, that can dissolve in water. An AR - AFFF type foam is recommended. Cover spill area with a fire-extinguishing foam. An aqueous film forming foam (AFFF) is recommended. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Collect as much of the spilled material as possible using non-sparking tools. Clean up residue with an appropriate solvent selected by a qualified and authorized person. Ventilate the area with fresh air. Read and follow safety precautions on the solvent label and MSDS. Seal the container. In the event of a release of this material, the user should determine if the release qualifies as reportable according to local, state, and federal regulations.
7.2 STORAGE
Store away from acids. Store away from heat. Store out of direct sunlight. Keep container tightly closed. Do not store containers on their sides. Store away from oxidizing agents.
MATERIAL SAFETY DATA SHEET Scotch Electrical Insulating Sealer 1601, Clear
06/27/11
Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with OSHA regulations: Half facepiece or fullface pressure demand self-contained breathing apparatus . Select and use respiratory protection to prevent an inhalation exposure based on the results of an exposure assessment. Consult with your respirator manufacturer for selection of appropriate types of respirators. 8.2.4 Prevention of Swallowing Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.
Authority
ACGIH ACGIH OSHA CMRG CMRG ACGIH ACGIH OSHA OSHA ACGIH ACGIH CMRG CMRG OSHA
Type
TWA STEL TWA TWA STEL TWA STEL TWA TWA TWA STEL TWA STEL TWA
Limit
500 ppm 750 ppm 2400 mg/m3 50 ppm 100 ppm 200 ppm 300 ppm 590 mg/m3 1800 mg/m3 100 ppm 150 ppm 50 ppm 75 ppm 435 mg/m3
Additional Information
SOURCE OF EXPOSURE LIMIT DATA: ACGIH: American Conference of Governmental Industrial Hygienists CMRG: Chemical Manufacturer Recommended Guideline OSHA: Occupational Safety and Health Administration AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
_________________________________________________________________________________________________ Page 5 of 9
MATERIAL SAFETY DATA SHEET Scotch Electrical Insulating Sealer 1601, Clear
06/27/11
Condition
During Combustion During Combustion
MATERIAL SAFETY DATA SHEET Scotch Electrical Insulating Sealer 1601, Clear
06/27/11
ID Number(s): 80-6101-3354-0, 80-6107-3294-5 For Transport Information, please visit http://3M.com/Transportinfo or call 1-800-364-3577 or 651-737-6501.
Reactivity Hazard - No
Section 313 Toxic Chemicals subject to the reporting requirements of that section and 40 CFR part 372 (EPCRA): Ingredient
XYLENE METHYL ETHYL KETONE
C.A.S. No
1330-20-7 78-93-3
% by Wt
15 - 20 10 - 15
STATE REGULATIONS
Contact 3M for more information.
CHEMICAL INVENTORIES
The components of this product are in compliance with the chemical notification requirements of TSCA. All applicable chemical ingredients in this material are listed on the European Inventory of Existing Chemical Substances (EINECS), or are exempt polymers whose monomers are listed on EINECS. Contact 3M for more information.
INTERNATIONAL REGULATIONS
Contact 3M for more information. WHMIS: Hazardous
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to be generated in significant quantities.
Reason for Reissue: Update to new format. Revision Changes: Section 1: Product name was modified. Section 16: Disclaimer (second paragraph) was modified. Section 3: Potential effects from skin contact information was modified. Section 3: Potential effects from inhalation information was modified. _________________________________________________________________________________________________ Page 7 of 9
MATERIAL SAFETY DATA SHEET Scotch Electrical Insulating Sealer 1601, Clear
06/27/11
Section 8: Skin protection phrase was modified. Section 8: Eye/face protection information was modified. Section 8: Respiratory protection - recommended respirators information was modified. Section 4: First aid for skin contact - decontamination - was modified. Section 4: First aid for skin contact - medical assistance - was modified. Section 4: First aid for inhalation - medical assistance - was modified. Section 14: Transportation legal text was modified. Section 3: Other health effects information was modified. Page Heading: Product name was modified. Section 15: Inventories information was modified. Section 9: Boiling point information was modified. Section 5: Flammable limits (UE) information was modified. Section 5: Flammable limits (LEL) information was modified. Section 8: Respiratory protection - recommended respirators guide was modified. Section 9: Flammable limits (LEL) information was modified. Section 9: Flammable limits (UEL) information was modified. Section 2: Ingredient table was modified. Section 8: Exposure guidelines ingredient information was modified. Section 4: Note to physicians heading was added. Section 4: Note to physicians was added. Section 6: 6.2. Environmental precautions heading was added. Section 6: 6.1. Personal precautions, protective equipment and emergency procedures heading was added. Section 10.1 Conditions to avoid heading was added. Section 10.2 Materials to avoid heading was added. Section 16: Web address was added. Section 6: Personal precautions information was added. Section 6: Environmental procedures information was added. Section 6: Methods for cleaning up information was added. Section 10: Materials to avoid physical property was added. Section 10: Conditions to avoid physical property was added. Section 8: Hand protection information was added. Section 1: Address was added. Copyright was added. Company logo was added. Section 6: Clean-up methods heading was added. Telephone header was added. Company Telephone was added. Section 1: Emergency phone information was added. Section 1: Emergency phone information was deleted. Company Logo was deleted. Copyright was deleted. Section 16: Web address heading was deleted. Section 6: Release measures information was deleted. Section 6: Release measures heading was deleted. Section 4: First aid for skin contact - termination of exposure - was deleted. Section 4: First aid for skin contact - handling - was deleted. Section 10: Materials and conditions to avoid physical property was deleted. Section 1: Address line 1 was deleted. Section 1: Address line 2 was deleted. Section 8: Exposure guidelines legend was deleted. DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely _________________________________________________________________________________________________ Page 8 of 9
MATERIAL SAFETY DATA SHEET Scotch Electrical Insulating Sealer 1601, Clear
06/27/11
within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for user's method of use or application. 3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M
_________________________________________________________________________________________________ Page 9 of 9