Issue Date
02 2012-06-30
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied. The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute the warranty of any kind, express or implied.
Contents
Contents
1 Introduction ........................................................................................................................... 1-1
1.1 Scope ...................................................................................................................................... 1-1 1.2 Intended Audience ................................................................................................................... 1-1 1.3 Change History ........................................................................................................................ 1-1
7 Parameters ............................................................................................................................ 7-1 8 Counters ................................................................................................................................ 8-1 9 Glossary ................................................................................................................................. 9-1 10 Reference Documents..................................................................................................... 10-1
Issue 02 (2012-06-30)
1 Introduction
1 Introduction
1.1 Scope
This document describes network control mode 2 (NC2) procedure, cell reselection algorithms, and cell reselection type in the NC2 feature. The feature involved is GBFD-116201 Network-Controlled Cell Reselection (NC2).
Personnel working on Huawei GPRS products or systems System operators who need a general understanding of this feature
Feature change Feature change refers to the change in the NC2 feature of a specific product version. Editorial change Editorial change refers to the change in wording or the addition of the information that was not described in the earlier version.
Document Issues
The document issues are as follows:
02 (2012-06-30)
This is the second commercial release of GBSS13.0.
Compared with issue 01 (2011-03-31) of GBSS13.0, issue 02 (2012-06-30) of GBSS13.0 incorporates the changes described in the following table. Change Description Parameter Change None. None.
Change Type
Feature change None. Editorial change Added the following chapters: Chapter 4 Related Features Chapter 5 Impact on the Network
01 (2011-03-31)
This is the commercial release of GBSS13.0.
Issue 02 (2012-06-30)
1-1
1 Introduction
Compared with issue Draft A (2011-01-15) of GBSS13.0, this issue incorporates no change.
Draft A (2011-01-15)
This is the draft release of GBSS13.0. Compared with issue 01 (2010-06-30) of GBSS12.0, issue Draft A (2011-01-15) of GBSS13.0 has no change.
Issue 02 (2012-06-30)
1-2
2 Overview
2 Overview
NC2 indicates network-controlled cell reselection. In the NC2 mode and GPRS Mobility Management (GMM) Ready state, the MS periodically sends packet measurement reports to the BSC. The BSC determines whether to perform cell reselection according to the packet measurement report from the MS, the current load in the serving cell and in the neighboring cells. If a cell reselection is required, the BSC sends a Packet Cell Change Order message to instruct the MS to reselect the target cell. Compared with the autonomous cell reselection of the MS, the network-controlled cell reselection comprehensively considers such factors as the receive level and load status in the serving cell and in the neighboring cell so that the MS can reselect a proper cell. In this way, the loads in the cells can be balanced. In NC2 mode, any of the following events triggers a network-controlled cell reselection.
The MS signal strength keeps falling, and a neighboring cell with stronger signal strength exists. The MS signal quality keeps deteriorating, and a neighboring cell with better signal quality exists. The serving cell of the MS is overloaded, and a neighboring cell with lighter load and stronger signal strength exists. The SGSN indicates that the Radio Access Technology (RAT, such as, GSM/EDGE Radio Access Network (GERAN), Universal Terrestrial Radio Access Network (UTRAN), or Evolved Universal Terrestrial Radio Access Network (EUTRAN)) most suitable for the MS is different from the current RAT.
In NC2 mode, any of the following events triggers an autonomous cell reselection rather than a network-controlled cell reselection.
Downlink signaling reception fails. Attempts to access the network fail. Visits to the serving cell are prohibited. The path loss criterion C1 indicates that the path loss of the serving cell is too high, that is, the value of the path loss criterion C1 is smaller than 0. Path loss criterion C1 is used to indicate the amount of path loss in a cell reselection decision.
In the GMM Standby state, the MS is attached to the GPRS network and an MM context is established between the MS and the SGSN. The MS can receive paging messages and downlink signaling but cannot transmit or receive packet data. In this case, the MS initiates autonomous cell reselection regardless of the NC mode. In Dual Transfer Mode (DTM), the MS does not perform any autonomous cell reselection or network-controlled cell reselection. Cell reselection is controlled by the CS domain handover procedure on the network side. An MS can perform the NC2 procedure in packet idle mode and in packet transfer mode.
NC2 in packet idle mode After an MS in packet idle mode completes the packet/immediate assignment procedure on the PCCCH/CCCH, it periodically sends packet measurement reports to the BSC through the PCCCH/CCCH. The interval at which the MS sends packet measurement reports is determined by the RPTPERIODI parameter. Through the PCCCH/CCCH, the BSC sends the Packet Cell Change Order message to the MS to instruct the MS to implement cell reselection and perform an NC2 procedure in packet idle mode.
NC2 in packet transfer mode An MS in packet transfer mode periodically sends packet measurement reports to the BSC through the PACCH. The interval at which the MS sends packet measurement reports is determined by the RPTPERIODT parameter. Through the PACCH, the BSC sends the Packet Cell Change Order message to the MS to instruct the MS to implement cell reselection and perform an NC2 procedure in packet transfer mode.
Issue 02 (2012-06-30)
2-1
2 Overview
The NC2 feature supports intra-BSC cell reselection, inter-BSC cell reselection, GERAN-to-UTRAN cell reselection, and GERAN-to-EUTRAN cell reselection.
Issue 02 (2012-06-30)
2-2
3 Technical Description
3 Technical Description
3.1 Procedure
If the cell configuration parameter NC2SPT is set to YES(Yes) and NCO is set to nc2(nc2), NC2 is enabled. If the NACCSPT parameter is set to YES(Yes), the cell reselection procedure in NC2 is accelerated. If the cell configuration parameter NC2SPT is set to YES(Yes) and NCO is set to nc2(nc2), the NC2 feature is enabled. If the INTERRATCELLRESELEN parameter is set to YES(Yes), GERAN-to-UTRAN cell reselection is enabled. If the LTECELLRESELEN parameter is set to YES(Yes), GERAN-to-EUTRAN cell reselection is enabled. If the NACCSPT parameter is set to YES(Yes), the cell reselection procedure in NC2 is accelerated. Figure 3-1 shows the cell reselection in NC2. Figure 3-1 Cell reselection in NC2
1. An MS in the GMM Ready state periodically sends Packet Measurement Report messages to the BSC. 2. After receiving the packet measurement report, the BSC processes the measurement results. According to the NC2 cell reselection algorithm, the BSC determines whether to perform a cell reselection and determines the target cell for reselection. 3. If the BSC determines to initiate a cell reselection, it sends a Packet Cell Change Order message to the MS to instruct the MS to reselect the specified target cell. When the NACCSPT parameter is set to YES(Yes), the BSC sends a Packet Neighbor Cell Data message to the MS before sending the Packet Cell Change Order message if the specified target cell is a GERAN cell or if the target cell is an external GERAN cell and the Gb interface supports the RAN Information Management (RIM) procedure. The Packet Neighbor Cell Data message carries the system information of the target cell to accelerate the cell reselection procedure.
Issue 02 (2012-06-30) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 3-1
3 Technical Description
4. If a cell reselection fails, the MS sends a Packet Cell Change Failure message to the BSC. After receiving this message, the BSC subtracts the value of the PENALTYRXLEV parameter from the receive level of the target cell.
If the PDU sent from the SGSN to the BSS indicates that the most suitable RAT for the current service is EUTRAN, then the MS performs a service-based cell reselection and the target cell is an EUTRAN cell. If a suitable target cell is not found, then the MS performs a quality-based, load-based, or coverage-based cell reselection and the target cell is the GERAN neighboring cell with the highest neighboring cell priority. If the PDU sent from the SGSN to the BSS indicates that the most suitable RATs for the current service are UTRAN and EUTRAN, then the MS performs a service-based cell reselection and the target cell is the neighboring cell with the highest neighboring cell priority. If the suitable target cell is not found, then the MS performs a quality-based, load-based, or coverage-based cell reselection. If the PDU sent from the SGSN to the BSS does not indicate any suitable RAT for the current service, then the MS performs a quality-based, load-based, or coverage-based cell reselection and the target cell is the neighboring cell with the highest neighboring cell priority.
When the NC2LoadResel parameter is set to Support, the load of the GERAN candidate cells under the same BSC is considered during cell reselection. When the NC2LoadResel parameter is set to NotSupport, the load of the GERAN candidate cells under the same BSC is not considered during cell reselection. The LOADBROADCASTPERIOD parameter specifies the interval at which a cell broadcasts its current load to its neighboring cells under the same BSC.
Issue 02 (2012-06-30)
3-2
3 Technical Description
Semantic Network initiated cell change order to UTRAN or PS handover to UTRAN procedure should not be performed Network initiated cell change order to UTRAN or PS handover to UTRAN procedure shall not be performed If received, shall be interpreted as information not available (bits 4-5 valid) If received, shall be interpreted as information not available
Table 3-2 Service EUTRAN CCO Value part Coding Bit 01 10 11 00 Semantic Network initiated cell change order to EUTRAN or PS handover to EUTRAN procedure should be performed Network initiated cell change order to EUTRAN or PS handover to EUTRAN procedure should not be performed Network initiated cell change order to EUTRAN or PS handover to EUTRAN procedure shall not be performed If received, shall be interpreted as information not available
When the Service UTRAN CCO Value part is set to 000 or when the Service E-UTRAN CCO Value part is set to 01, a service-based cell reselection is initiated. The details about the service-based cell reselection algorithm are as follows:
When the Service UTRAN CCO Value part is set to 000 and the Service E-UTRAN CCO Value part is not set to 01, the cell with the highest received signal level is selected as the target cell from the neighboring UTRAN cells. When the Service UTRAN CCO Value part is set to 000 and the Service E-UTRAN CCO Value part is set to 01, NCELLPRI for UTRAN and NCELLPRI for E-UTRAN neighboring cells in neighboring cell relationship is compared and the neighboring cell with the highest neighboring cell priority is reselected. When the Service UTRAN CCO Value part is not set to 000 and the Service E-UTRAN CCO Value part is set to 01, the cell with the highest received signal level is selected as the target cell from the neighboring EUTRAN cells.
If a UTRAN or EUTRAN target cell is not found, then the MS performs a quality-based, load-based, or coverage-based cell reselection. When the Service UTRAN CCO Value part is not set to 000 and the Service E-UTRAN CCO Value part is not set to 01, then the MS performs a quality-based, load-based, or coverage-based cell reselection.
3 Technical Description
link. If the BER increases, the possible cause is that the signal level is too low or there is interference on the channel. In this case, the BSC instructs the MS to reselect a neighboring cell with higher signal level. In a measurement period of the receive quality, if the MS receive quality deterioration ratio is greater than the value of the CELLRXQUALWORSENRATIOTHRSH parameter, a quality-based cell reselection is initiated. MS receive quality deterioration ratio indicates the ratio of times of bad MS downlink quality to number of downlink quality MRs. In a quality-based cell reselection, the cell with the highest priority is selected as the target cell from the list of GERAN candidate cells if GERAN is of the highest priority. The priority of a cell is determined by the received signal level and the characteristics information such as cell type, cell priority, and support of EDGE, about the cell. If UTRAN or EUTRAN is of the highest priority, the cell with the highest received signal level is selected as the target cell from the UTRAN or EUTRAN candidate cells. When the NC2LoadResel parameter is set to Support, the characteristics information about a cell also includes the load of the GERAN candidate cells under the same BSC. A neighboring candidate cell must meet any of the following conditions:
Receive level of the neighboring GERAN candidate cell > Max(Receive level of the serving cell, MINACCRXLEV) + RESELHYST. Measured ratio of energy per modulating bit to the noise spectral density (Ec/No) of the neighboring Frequency Division Duplex (FDD) cell > FDDECQUALTHRSH, or measured Received Signal Code Power (RSCP) of the neighboring FDD cell > FDDRSCPQUALTHRSH. Measured RSCP of the neighboring Time Division Duplex (TDD) cell > TDDRSCPQUALTHRSH. When the NC2LoadResel parameter is set to Support, the neighboring GERAN candidate cells under the same BSC are not congested. When the Service UTRAN CCO Value part is set to 010 or 001, none of the neighboring UTRAN cells (TDD cells and FDD cells) can be selected as the target cell. When the Service E-UTRAN CCO Value part is set to 10 or 11, none of the EUTRAN cells can be selected as the target cell.
Issue 02 (2012-06-30)
3-4
3 Technical Description
To determine the traffic load of a cell, compare the channel multiplexing rate with the predefined threshold:
If the average channel multiplexing rate of a cell is higher than the value of the LOADRESELSTARTTHRSH parameter, the load in the cell is heavy, and therefore the load-based cell reselection should be enabled. If the average channel multiplexing rate of a cell is lower than the value of the LOADRESELRXTHRSH parameter, the load in the cell is light and some loads in heavily-loaded cells can be redirected to this cell.
In a load-based cell reselection, an MS with a high signal level cannot be reselected to a neighboring cell. By setting the LOADRESELMAXRXLEV parameter, only the MS whose signal level is lower than the value of the LOADRESELMAXRXLEV parameter can be reselected to a neighboring cell. A load-based cell reselection can be initiated only when the serving cell is overloaded and the received signal level in this cell is lower than the value of the LOADRESELMAXRXLEV parameter. In a load-based cell reselection, the cell with the highest priority is selected as the target cell from the GERAN candidate cells if GERAN is of the highest priority. The priority of a cell is determined by the received signal level and the characteristics information such as cell type, cell priority, and support of EDGE, about the cell. If UTRAN or EUTRAN is of the highest priority, the cell with the highest received signal level is selected as the target cell from the UTRAN or EUTRAN candidate cells. When the NC2LoadResel parameter is set to Support, the characteristics information about a cell also includes the load of the GERAN candidate cells under the same BSC. A neighboring candidate cell must meet any of the following conditions:
Receive level of the neighboring GERAN candidate cell > Max(Receive level of the serving cell, MINACCRXLEV) + RESELHYST. Measured Ec/No of the neighboring FDD cell > FDDECQUALTHRSH, or Measured RSCP of the neighboring FDD cell > FDDRSCPQUALTHRSH. Measured RSCP of the neighboring TDD cell > TDDRSCPQUALTHRSH. When the NC2LoadResel parameter is set to Support, the neighboring GERAN candidate cells under the same BSC are not congested. When the Service UTRAN CCO Value part is set to 010 or 001, none of the neighboring UTRAN cells (TDD cells and FDD cells) can be selected as the target cell. When the Service E-UTRAN CCO Value part is set to 10 or 11, none of the EUTRAN cells can be selected as the target cell.
3 Technical Description
NC2LoadResel parameter is set to Support, the characteristics information about a cell also includes the load of the GERAN candidate cells under the same BSC. A neighboring candidate cell must meet any of the following conditions:
Receive level of the neighboring GERAN candidate cell > Max(Receive level of the serving cell, MINACCRXLEV) + RESELHYST. Measured Ec/No of the neighboring FDD cell > FDDECQUALTHRSH, or Measured RSCP of the neighboring FDD cell > FDDRSCPQUALTHRSH. Measured RSCP of the neighboring TDD cell > TDDRSCPQUALTHRSH. When the NC2LoadResel parameter is set to Support, the neighboring GERAN candidate cells under the same BSC are not congested. When the Service UTRAN CCO Value part is set to 010 or 001, none of the neighboring UTRAN cells (TDD cells and FDD cells) can be selected as the target cell. When the Service E-UTRAN CCO Value part is set to 10 or 11, none of the EUTRAN cells can be selected as the target cell.
Issue 02 (2012-06-30)
3-6
3 Technical Description
Issue 02 (2012-06-30)
3-7
4 Related Features
4 Related Features
Feature/Function Network-Controlled Cell Reselection (NC2) GSM-to-WCDMA Network-Controlled Cell Reselection Prerequisite Feature GBFD-114101 GPRS GBFD-114101 GPRS GBFD-114301 GSM/WCDMA Interoperability Mutually Exclusive Feature GBFD-114151 DTM None Affected Feature None None
Issue 02 (2012-06-30)
4-1
Issue 02 (2012-06-30)
5-1
6 Engineering Guidelines
6 Engineering Guidelines
6.1 When to Use NC2
It is recommended that this feature be used when traffic loads among cells are imbalanced.
Network Topology
N/A
Hardware Planning
The DPUd or DPUg board has been configured.
6.6 Troubleshooting
None
Issue 02 (2012-06-30)
6-1
7 Parameters
7 Parameters
Table 7-1 Parameter description Parameter ID NE MML Command Feature ID Feature Name Description
CELLRXQUALWORSENRA BSC6 SET GBFD-11 Network-Cont Meaning: The TIOTHRSH 900 GCELLNC2PARA(Optional 6201 rolled Cell number of ) Reselection times that the GBFD-51 (NC2) downlink 1303 PS Handover transmission quality of the Between MS is lower GSM and LTE Based than the transmission on Quality quality threshold of the MS ("EDGE GMSK Quality Threshold", "EDGE 8PSK Quality Threshold", or "GPRS Quality Threshold" by TBF type) is calculated accumulativel y. When the rate of the accumulated value to the number of received measurement reports on the downlink transmission quality (Packet Downlink Ack/Nack message) is greater than or equal to the value of this parameter, the emergency reselection is triggered. GUI Value Range: 0~100 Actual Value
Issue 02 (2012-06-30)
7-1
7 Parameters
Parameter ID
NE
MML Command
Feature ID
Feature Name
EUTRANPRI
BSC6 SET GBFD-51 Cell 900 GCELLPRIEUTRANSYS(O 1301 Reselection ptional) GBFD-51 Between GSM and 1312 LTE
Meaning: Priority of EUTRAN. Value 0 indicates the lowest priority, Fast LTE Reselection and value 7 at 2G CS Call indicates the highest Release priority. GUI Value Range: 0~7 Actual Value Range: 0~7 Default Value: 0 Unit: None
FDDECQUALTHRSH
GBFD-11 GSM/WCDM Meaning: 4301 A Minimum Interoperabilit Ec/No of the y 3G FDD cell candidate GUI Value Range: 0~49 Actual Value Range: 0~49 Default Value: 10 Unit: dB
FDDRSCPQUALTHRSH
GBFD-11 GSM/WCDM Meaning: 4301 A Minimum Interoperabilit RSCP of the y 3G FDD cell candidate GUI Value Range: 0~63 Actual Value Range: 0~63 Default Value: 10 Unit: None
Issue 02 (2012-06-30)
7-2
7 Parameters
Parameter ID GERANPRI
NE
MML Command
Feature ID
Feature Name
Description Meaning: Priority of GERAN. Value 0 indicates the lowest priority, and value 7 indicates the highest priority. GUI Value Range: 0~7 Actual Value Range: 0~7 Default Value: 7 Unit: None
BSC6 SET GBFD-51 Cell 900 GCELLPRIEUTRANSYS(O 1301 Reselection ptional) Between GSM and LTE
INTERRATCELLRESELEN BSC6 SET GBFD-51 GSM and 900 GCELLHOBASIC(Optional) 1104 WCDMA GBFD-11 Traffic Steering 4302 Based on Iur-g
Meaning: This parameter specifies whether the reselection from 2G cells GSM/TD-SC to 3G cells is allowed. DMA Interoperabilit GUI Value y Range: NO(No), YES(Yes) Actual Value Range: NO, YES Default Value: NO Unit: None
LOADBROADCASTPERIO BSC6 SET GBFD-11 Network-Cont Meaning: D 900 BSCPSSOFTPARA(Option 6201 rolled Cell Intervals that al) Reselection the BSC (NC2) broadcasts a cell's traffic load to its neighbor cells. The uplink load and downlink load indicate the traffic situation of a cell. The
Issue 02 (2012-06-30)
7-3
7 Parameters
Parameter ID
NE
MML Command
Feature ID
Feature Name
Description uplink load = number of uplink TBFs carried on all PDCHs in a cell / total number of PDCHs in a cell x ("PDCH Uplink Multiplex Threshold"/10) x 100%. The downlink load = number of downlink TBFs carried on all PDCHs in a cell / total number of PDCHs in a cell x ("PDCH Downlink Multiplex Threshold"/10) x 100%. GUI Value Range: 1~10 Actual Value Range: 1~10 Default Value: 4 Unit: s
LOADRESELALLOW
BSC6 SET GBFD-11 Network-Cont Meaning: 900 GCELLNC2PARA(Optional 6201 rolled Cell Whether to ) Reselection allow the cell GBFD-51 (NC2) load 1304 reselection. If GBFD-51 PS Handover this parameter Between 1307 is set to GSM and LTE Based PERMIT and on Cell Load "NC2 Load Reselection eNC2 Switch" is set Between to Support, the GSM and load of the LTE target cell is involved in the algorithm for NC2 cell
Issue 02 (2012-06-30)
7-4
7 Parameters
Parameter ID
NE
MML Command
Feature ID
Feature Name
Description reselection. GUI Value Range: FORBID(Forbi d), PERMIT(Perm it) Actual Value Range: FORBID, PERMIT Default Value: PERMIT Unit: None
LOADRESELMAXRXLEV
BSC6 SET GBFD-11 Network-Cont Meaning: 900 GCELLNC2PARA(Optional 6201 rolled Cell Threshold for ) Reselection allowing the GBFD-51 (NC2) MS to reselect 1304 PS Handover a cell during load Between reelection. GSM and LTE Based When the on Cell Load receive level of the serving cell is lower than this threshold, the load reselection is triggered. GUI Value Range: 0~63 Actual Value Range: 0~63 Default Value: 40 Unit: None
LOADRESELRXTHRSH
BSC6 SET GBFD-11 Network-Cont Meaning: 900 GCELLNC2PARA(Optional 6201 rolled Cell When the ) Reselection uplink load or GBFD-11 (NC2) downlink load 4301 of the target GBFD-11 GSM/WCDM cell is lower A 4322 Interoperabilit than this GBFD-51 y threshold, it 1304 can accept the GSM/WCDM MSs from the GBFD-51 A Load serving cell 1310 Based
Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 7-5
Issue 02 (2012-06-30)
7 Parameters
Parameter ID
NE
MML Command
Feature ID
Description
due to load PS Handover reselection. Between GUI Value Range: 0~100 GSM and LTE Based Actual Value on Cell Load Range: 0~100 Multi Technology Neighbour Cell Based Handover Default Value: 60 Unit: %
LOADRESELSTARTTHRS BSC6 SET GBFD-11 Network-Cont Meaning: H 900 GCELLNC2PARA(Optional 6201 rolled Cell When the ) Reselection uplink load or GBFD-51 (NC2) downlink load 1304 PS Handover of the cell exceeds this Between threshold, the GSM and LTE Based load on Cell Load reselection decision is made. GUI Value Range: 0~100 Actual Value Range: 0~100 Default Value: 85 Unit: % LTECELLRESELEN BSC6 SET GBFD-51 Cell 900 GCELLHOBASIC(Optional) 1301 Reselection GBFD-51 Between GSM and 1312 LTE Meaning: Whether to allow cell reselection from GSM to LTE.
Fast LTE Reselection GUI Value at 2G CS Call Range: Release NO(No), YES(Yes)
Actual Value Range: NO, YES Default Value: NO Unit: None MINACCRXLEV BSC6 SET GBFD-11 Network-Cont Meaning: GCELLNC2PARA(Optional rolled Cell Minimum
Issue 02 (2012-06-30)
7-6
7 Parameters
Parameter ID
NE 900
MML Command )
Feature ID 6201
Feature Name
Description
Reselection GBFD-51 (NC2) 1302 PS Handover GBFD-51 Between GSM and 1303 LTE Based GBFD-51 on Coverage 1304 PS Handover GBFD-51 Between 1306 GSM and LTE Based on Quality
receive level for a neighbor cell to become a candidate cell during cell reselection. When the receive level of the serving cell is lower than the value of this parameter, it PS Handover indicates that Between the normal cell GSM and reselection LTE Based level is bad. In on Cell Load this case, the parameter GSM/LTE value is used Service for the Based PS calculation of Handover the times of the occurrence of bad normal cell reselection level. GUI Value Range: 0~63 Actual Value Range: 0~63 Default Value: 15 Unit: None
NACCSPT
GBFD-11 Network 6301 Assisted Cell GBFD-11 Change (NACC) 9502 PS Handover
Meaning: Whether to support Network Assisted Cell Change (NACC). NACC is used in the network control mode NC0, NC1 or NC2. When an MS is in packet
Issue 02 (2012-06-30)
7-7
7 Parameters
Parameter ID
NE
MML Command
Feature ID
Feature Name
Description transfer mode, the NACC enables the network to notify the MS in advance of the system information about neighboring cells, accelerating cell reselection for MSs. GUI Value Range: NO(No), YES(Yes) Actual Value Range: NO, YES Default Value: NO Unit: None
NC2LoadResel
BSC6 SET GBFD-11 Network-Cont Meaning: 900 BSCPSSOFTPARA(Option 6201 rolled Cell Whether to al) Reselection involve the (NC2) load of the target cell in the algorithm for NC2 cell reselection. If this parameter is set to Support, the load of the target cell is involved in the algorithm for NC2 cell reselection. GUI Value Range: NotSupport(N ot Support), Support(Supp ort) Actual Value Range:
Issue 02 (2012-06-30)
7-8
7 Parameters
Parameter ID
NE
MML Command
Feature ID
Feature Name
NC2SPT
GBFD-11 Network-Cont Meaning: 6201 rolled Cell Whether to Reselection support GBFD-11 (NC2) network 9502 control 2 GBFD-51 PS Handover (NC2). In NC2 1307 eNC2 mode, an MS GBFD-51 Between sends the GSM and 1310 BSC LTE measurement Multi reports Technology containing Neighbour information Cell Based about the Handover serving cell and neighboring cells, and the network controls cell reselection for the MS. GUI Value Range: NO(No), YES(Yes) Actual Value Range: NO, YES Default Value: NO Unit: None
NCELLPRI
Meaning: Priority of the neighboring cell. Value 0 indicates the lowest priority, and value 7 indicates the highest priority. Value 255 is invalid.
Issue 02 (2012-06-30)
7-9
7 Parameters
Parameter ID
NE
MML Command
Feature ID
Feature Name
Description GUI Value Range: 0~7, 255 Actual Value Range: 0~7, 255 Default Value: 255 Unit: None
NCELLPRI
BSC6 ADD G2GNCELL(Optional) GBFD-11 Basic Cell Meaning: 900 0402 Re-selection Priority of the MOD neighboring G2GNCELL(Optional) cell. Value 0 indicates the lowest priority, and value 7 indicates the highest priority. Value 255 is invalid. GUI Value Range: 0~7, 255 Actual Value Range: 0~7, 255 Default Value: 255 Unit: None
NCELLPRI
BSC6 ADD G3GNCELL(Optional) GBFD-11 900 4301 MOD G3GNCELL(Optional) GBFD-11 4302
GSM/WCDM Meaning: A Priority of the Interoperabilit neighboring y cell. Value 0 GSM/TD-SC indicates the lowest priority, DMA Interoperabilit and value 7 indicates the y highest priority. Value 255 is invalid. GUI Value Range: 0~7, 255 Actual Value Range: 0~7, 255 Default Value:
Issue 02 (2012-06-30)
7-10
7 Parameters
Parameter ID
NE
MML Command
Feature ID
Feature Name
NCO
BSC6 SET GBFD-11 Networking Meaning: 900 GCELLPSBASE(Optional) 9107 Control Mode Network GBFD-11 GSM/TD-SC control mode for cell 4302 DMA reselection of GBFD-11 Interoperabilit the MS. There y 9502 are three GBFD-11 PS Handover modes. NC0: 1101 System GBFD-51 Information Sending 1307 GBFD-51 eNC2 Between 1310 GSM and LTE Multi Technology Neighbour Cell Based Handover normal MS control. The MS shall perform autonomous cell re-selection. NC1: MS control with measurement reports. The MS shall send measurement reports to the network and the MS shall perform autonomous cell re-selection. NC2: network control. The MS shall send measurement reports to the network. The MS shall only perform autonomous cell re-selection when the reselection is triggered by a downlink signaling failure or a random access failure. When this parameter is
Issue 02 (2012-06-30)
7-11
7 Parameters
Parameter ID
NE
MML Command
Feature ID
Feature Name
Description set to NC2 and "Support NC2" in "SET GCELLGPRS" is set to "YES", the network side can control the cell reselection for the MS. GUI Value Range: NC0(NC0), NC1(NC1), NC2(NC2) Actual Value Range: NC0, NC1, NC2 Default Value: NC0 Unit: None
NORMALRESELALLOW
BSC6 SET GBFD-11 Network-Cont Meaning: 900 GCELLNC2PARA(Optional 6201 rolled Cell Whether to ) Reselection allow the cell GBFD-51 (NC2) normal 1302 reselection. If GBFD-51 PS Handover this parameter Between 1307 is set to GSM and LTE Based PERMIT and on Coverage "NC2 Load Reselection eNC2 Switch" is set Between to Support, the GSM and load of the LTE target cell is involved in the algorithm for NC2 cell reselection. GUI Value Range: FORBID(Forbi d), PERMIT(Perm it) Actual Value Range: FORBID,
Issue 02 (2012-06-30)
7-12
7 Parameters
Parameter ID
NE
MML Command
Feature ID
Feature Name
PENALTYLASTTM
BSC6 SET GBFD-11 Network-Cont Meaning: 900 GCELLNC2PARA(Optional 6201 rolled Cell Penalty ) Reselection duration for GBFD-51 (NC2) cell 1302 reselection. GBFD-51 PS Handover Cell penalty Between 1303 can be GSM and GBFD-51 LTE Based performed 1304 on Coverage only in this GBFD-51 PS Handover duration. When this 1306 Between parameter is GBFD-51 GSM and set to a 1310 LTE Based greater value, on Quality the MS cannot PS Handover reselect a cell Between for a longer GSM and time in the LTE Based case of on Cell Load reselection failure or GSM/LTE reselection Service due to load. Based PS The penalty Handover timer is shorter Multi when this Technology parameter is Neighbour set to a Cell Based smaller value. Handover GUI Value Range: 0~255 Actual Value Range: 0~255 Default Value: 10 Unit: s
PENALTYRXLEV
BSC6 SET GBFD-11 Network-Cont Meaning: 900 GCELLNC2PARA(Optional 6201 rolled Cell When the cell ) Reselection reselection GBFD-51 (NC2) failure 1302 message is GBFD-51 PS Handover received or Between 1303 the load cell GSM and GBFD-51 LTE Based reselection is 1304 initiated, the
Issue 02 (2012-06-30)
7-13
7 Parameters
Parameter ID
NE
MML Command
Feature ID
Feature Name
Description
GBFD-51 on Coverage 1306 PS Handover GBFD-51 Between 1310 GSM and LTE Based on Quality
"Cell Penalty Level" is subtracted from the receive level of the target cell to avoid PS Handover that cell Between reselection GSM and failure occurs LTE Based repeatedly or on Cell Load that multiple GSM/LTE MSs are Service reselected to Based PS the same Handover target cell. This Multi Technology parameter is valid only Neighbour Cell Based within "Cell Penalty Handover Duration". GUI Value Range: 0~63 Actual Value Range: 0~63 Default Value: 30 Unit: None
RESELHYST
BSC6 SET GBFD-11 Network-Cont Meaning: 900 GCELLNC2PARA(Optional 6201 rolled Cell Indicating that ) Reselection during cell GBFD-51 (NC2) reselection, 1302 the level of the GBFD-51 PS Handover target cell Between 1303 should meet GSM and GBFD-51 LTE Based the following 1304 on Coverage condition: GBFD-51 PS Handover Level of target cell > [MAX 1306 Between (level of GBFD-51 GSM and serving cell, 1310 LTE Based "Cell on Quality Reselection PS Handover Level Between Threshold") + GSM and "Cell LTE Based Reselection on Cell Load Hysteresis"]. In this way, GSM/LTE
Issue 02 (2012-06-30)
7-14
7 Parameters
Parameter ID
NE
MML Command
Feature ID
Feature Name Service Based PS Handover Multi Technology Neighbour Cell Based Handover
Description ping-pong handovers do not occur. GUI Value Range: 0~63 Actual Value Range: 0~63 Default Value: 6 Unit: None
RESELWATCHPERIOD
BSC6 SET GBFD-11 Network-Cont Meaning: The 900 GCELLNC2PARA(Optional 6201 rolled Cell number of ) Reselection received GBFD-51 (NC2) Packet 1302 PS Handover Measurement Report Between messages on GSM and LTE Based the receive on Coverage level of the serving cell is measured continuously. When the statistical value is greater than or equal to the value of this parameter, the normal reselection decision is made. GUI Value Range: 1~32 Actual Value Range: 1~32 Default Value: 10 Unit: None
RESELWORSENLEVTHRS BSC6 SET GBFD-11 Network-Cont Meaning: If H 900 GCELLNC2PARA(Optional 6201 rolled Cell the number of ) Reselection times when GBFD-51 (NC2) the receive 1302 PS Handover level of the serving cell Between within "Normal GSM and LTE Based Cell
Issue 02 (2012-06-30)
7-15
7 Parameters
Parameter ID
NE
MML Command
Feature ID
Feature Name
Description
on Coverage Reselection Watch Period" is lower than "Cell Reselection Level Threshold" is greater than the value of this parameter, the normal cell reselection is triggered. GUI Value Range: 1~32 Actual Value Range: 1~32 Default Value: 1 Unit: None RPTPERIODI BSC6 SET GBFD-11 Networking Meaning: Cell 900 Control Mode reselection GCELLNWCTRLMSRPAR 9107 A(Optional) measurement report period in packet idle mode GUI Value Range: 0.48sec(0.48s ec), 0.96sec(0.96s ec), 1.92sec(1.92s ec), 3.84sec(3.84s ec), 7.68sec(7.68s ec), 15.36sec(15.3 6sec), 30.72sec(30.7 2sec), 61.44sec(61.4 4sec) Actual Value Range: 0.48sec, 0.96sec, 1.92sec,
Issue 02 (2012-06-30) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 7-16
7 Parameters
Parameter ID
NE
MML Command
Feature ID
Feature Name
Description 3.84sec, 7.68sec, 15.36sec, 30.72sec, 61.44sec Default Value: 15.36sec Unit: s
RPTPERIODT
BSC6 SET GBFD-11 Networking Meaning: 900 Control Mode Interval at GCELLNWCTRLMSRPAR 9107 A(Optional) GBFD-11 GSM/TD-SC which an MS in packet 4302 DMA Interoperabilit transfer mode sends y measurement reports for cell reselection. GUI Value Range: 0.48sec(0.48s ec), 0.96sec(0.96s ec), 1.92sec(1.92s ec), 3.84sec(3.84s ec), 7.68sec(7.68s ec), 15.36sec(15.3 6sec), 30.72sec(30.7 2sec), 61.44sec(61.4 4sec) Actual Value Range: 0.48sec, 0.96sec, 1.92sec, 3.84sec, 7.68sec, 15.36sec, 30.72sec, 61.44sec Default Value: 0.96sec Unit: s
TDDRSCPQUALTHRSH
BSC6 ADD
Issue 02 (2012-06-30)
7-17
7 Parameters
Parameter ID
NE 900
Feature ID 4302
Feature Name
Description
DMA Minimum Interoperabilit RSCP quality y threshold that the TDD 3G candidate cell must reach GUI Value Range: 0~63 Actual Value Range: 0~63 Default Value: 10 Unit: None
URGENTRESELALLOW
BSC6 SET GBFD-11 Network-Cont Meaning: 900 GCELLNC2PARA(Optional 6201 rolled Cell Whether to ) Reselection allow cell GBFD-51 (NC2) urgent 1303 reselection. If GBFD-51 PS Handover this parameter Between 1307 is set to GSM and LTE Based PERMIT and "NC2 Load on Quality Reselection eNC2 Switch" is set Between to Support, the GSM and load of the LTE target cell is involved in the algorithm for NC2 cell reselection. GUI Value Range: FORBID(Forbi d), PERMIT(Perm it) Actual Value Range: FORBID, PERMIT Default Value: PERMIT Unit: None
UTRANPRI
BSC6 SET GBFD-51 Cell 900 GCELLPRIEUTRANSYS(O 1301 Reselection ptional) Between GSM and
Issue 02 (2012-06-30)
7-18
7 Parameters
Parameter ID
NE
MML Command
Feature ID
Description lowest priority, and value 7 indicates the highest priority. GUI Value Range: 0~7 Actual Value Range: 0~7 Default Value: 1 Unit: None
Issue 02 (2012-06-30)
7-19
8 Counters
8 Counters
Table 8-1 Counter description Counter ID Counter Name 127917242 NC.CELL.RESELECT.ATMPT 6 Counter Description Feature ID Feature Name
H9010:Number of GBFD-11620 Network-Controlle Network-Controlle 1 d Cell Reselection (NC2) d Cell Reselection Attempts H9011:Number of GBFD-11620 Network-Controlle Network-Controlle 1 d Cell Reselection (NC2) d Cell Reselection Attempts Due to Downlink Quality H9012:Number of GBFD-11620 Network-Controlle Network-Controlle 1 d Cell Reselection (NC2) d Cell Reselection Attempts due to Traffic Load
127917242 NC.CELL.URG.RESELECT.ATMPT 7
127917242 NC.CELL.LOAD.RESELECT.ATMPT 8
127917242 NC.CELL.GENERAL.RESELECT.ATM H9013:Number of GBFD-11620 Network-Controlle 9 PT Network-Controlle 1 d Cell Reselection (NC2) d Cell Reselection Attempts for Better Cell 127917243 NC.CELL.RESELECT.FAIL.ATMPT 0 H9014:Number of GBFD-11620 Network-Controlle 1 Failed d Cell Reselection (NC2) Network-Controlle d Cell Reselections
127917243 NC.CELL.INTRABSC.RESELECT.ATM H9015:Number of GBFD-11620 Network-Controlle 1 PT 1 Intra-BSC d Cell Reselection (NC2) Network-Controlle d Cell Reselection Attempts 127917243 NC.CELL.INTERBSC.RESELECT.ATM H9016:Number of GBFD-11620 Network-Controlle 2 PT 1 Inter-BSC d Cell Reselection (NC2) Network-Controlle d Cell Reselection Attempts 127917243 NC.CELL.INTERRAN.RESELECT.ATM H9017:Number of GBFD-11620 Network-Controlle 3 PT 1 Inter-RAT d Cell Reselection (NC2) Network-Controlle d Cell Reselection Attempts 127917243 NC.CELL.2G.TO.3G.RESELECT.ATMP H9018:Number of GBFD-11620 Network-Controlle 4 T Network-Controlle 1 d Cell Reselection (NC2) d 2G to 3G Cell
Issue 02 (2012-06-30)
8-1
8 Counters
Feature ID
Feature Name
127917243 NC.CELL.2G.TO.3G.RESELECT.FAIL H9019:Number of GBFD-11620 Network-Controlle 5 1 Failed d Cell Reselection (NC2) Network-Controlle d 2G to 3G Cell Reselections 128242961 NC.CELL.2G.TO.4G.RESELECT.ATMP H9701:Number of GBFD-11620 3 T Network-Controlle 1 d 2G to 4G Cell GBFD-51130 Reselection 7 Attempts 128242961 NC.CELL.2G.TO.4G.RESELECT.FAIL H9721:Number of GBFD-11620 4 1 Failed Network-Controlle GBFD-51130 d 2G to 4G Cell 7 Reselections Network-Controlle d Cell Reselection (NC2) eNC2 Between GSM and LTE Network-Controlle d Cell Reselection (NC2) eNC2 Between GSM and LTE
Issue 02 (2012-06-30)
8-2
9 Glossary
9 Glossary
For the acronyms, abbreviations, terms, and definitions, see the Glossary.
Issue 02 (2012-06-30)
9-1
10 Reference Documents
10 Reference Documents
[1] 3GPP TS 45.008: "Radio subsystem link control" [2] 3GPP TS 44.060: "Radio Link Control (RLC) / Medium Access Control (MAC) protocol" [3] 3GPP TS 43.064: "Overall description of the GPRS Radio Interface; Stage 2" [4] 3GPP TS 43.022: "Functions related to Mobile Station (MS) in idle mode and group receive mod" [5] BSC6900 Feature List [6] BSC6900 Optional Feature Description [7] BSC6900 GSM Parameter Reference [8] BSC6900 GSM MML Command Reference [9] BSC6900 Performance Counter Reference
Issue 02 (2012-06-30)
10-1