1 (20)
The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation. The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given as is and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document. Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL NOKIA SIEMENS NETWORKS BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA, THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT. This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws. The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG. Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only. Copyright Nokia Siemens Networks 2007. All rights reserved.
2 (20)
Contents
Contents
Contents 3 List of tables 4 List of figures 5 Summary of changes 7 1 1.1 1.2 2 3 Before starting to unpack 9 Dimensions and weights of the packages Conversion factors 11 Opening the packing case 13 Lifting and moving the cabinet 17 9
3 (20)
List of tables Table 1. Table 2. Table 3. Dimensions and weights of cabinet packages. Conversion factors. 11 11 9
4 (20)
List of figures
Cut the polyester bands attaching the package to the wooden platform at four points. Remove the outer case placed over the inner packing case. 13 The inner packing case with the outer case removed. Also remove the upper lid on top of the packing case. 13 Remove the absorbers from the top of the cabinet. 14 14 15
Remove the rolls from the corners of the packing case. Remove the cardboard collar surrounding the cabinet. Open the barrier bag. 15
Open the ends of the cardboard base and carefully remove the absorbers from under the cabinet. 16 Unwrap the plastic around the cabinet and carefully lift the cabinet up on its feet (EC216) or on its support feet (IC186-B). 17 18
Figure 11. If you are unpacking an EC216 cabinet, remove the protective cardboards from the sides. 18 Figure 12. If you are unpacking an IC186-B cabinet, remove the support feet at the installation site. 19 Figure 13. Lifting the cabinet from the subrack or stepping on or forcefully pushing down the subrack edges will bend and damage it. 20
5 (20)
6 (20)
Summary of changes
Summary of changes
Changes between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues.
7 (20)
8 (20)
1
1.1
Make sure that the unpacking area is empty. Fetch all utensils needed for unpacking from storage (knife or side cutters)
Table 1.
Package type
Single EC216
Weight
280-310 kg (617-683 lb)
EC216 + EC213
Single IC186-B
9 (20)
Table 1.
Package type
Single IC183-B
Weight
130-150 kg (287-331 lb)
IC186-B + IC183-B
Note that up to three cabinet packages can be piled on top of each other, as shown in figure 1. The maximum heigth of any delivery type is 4000 mm.
Figure 1.
10 (20)
1.2
Conversion factors
The following conversion factors should be used when installing Nokia's IPA2800 and associated equipment:
Table 2. Metric
The following table can be used for converting decimals to fractions, where the first column gives the number of inches in decimals and the second column contains the corresponding number of inches in fractional form. The third column gives the number of feet in decimals, and the fourth column gives the corresponding number of inches in fractional form.
Decimals (feet)
.1 .2 .3 .4 .5 .6 .7 .8 .9 1.0
Fractions (Inches)
1 1/2 3 4 1/2 5 1/4 6 7 1/2 8 1/4 9 3/4 10 1/2 12
11 (20)
Note
For the purposes of installation and construction, an allowance of 1/ 16th of an inch is tolerated between the physical conditions found on any particular site and the Blueprint drawings provided with the installation instructions. In addition, an allowance of 1/16th of an inch will be permitted when converting directly from European measurement to the American standard feet and inches.
12 (20)
Figure 2.
Cut the polyester bands attaching the package to the wooden platform at four points. Remove the outer case placed over the inner packing case.
Figure 3.
The inner packing case with the outer case removed. Also remove the upper lid on top of the packing case.
13 (20)
Figure 4.
Figure 5.
14 (20)
Figure 6.
Figure 7.
15 (20)
Figure 8.
Open the ends of the cardboard base and carefully remove the absorbers from under the cabinet.
16 (20)
Figure 9.
Unwrap the plastic around the cabinet and carefully lift the cabinet up on its feet (EC216) or on its support feet (IC186-B).
17 (20)
Figure 10.
Figure 11.
If you are unpacking an EC216 cabinet, remove the protective cardboards from the sides.
18 (20)
Figure 12.
If you are unpacking an IC186-B cabinet, remove the support feet at the installation site.
The cabinet doors must be kept closed when lifting and moving the cabinet. Do not lift or move the cabinet from the subracks, because it will bend the subrack.
19 (20)
Figure 13.
Lifting the cabinet from the subrack or stepping on or forcefully pushing down the subrack edges will bend and damage it.
20 (20)