October 2000
431
ICS 21.060.20 Rohrmuttern mit Rohrgewinde nach ISO 228-1 In keeping with current practice in standards published by the International Organization for Standardization (ISO), a comma has been used throughout as the decimal marker. Supersedes February 2000 edition.
Foreword
This standard has been prepared by Technical Committee Schrauben und Muttern mit Auenantrieb of the Normenausschuss Mechanische Verbindungselemente (Fasteners Standards Committee). Amendments This standard differs from the February 2000 edition in that the designation has been amended by including the width across flats for sizes G 1/8, G 1/4, G 1/2 and G 5/8, and that the mass for sizes G 1/8, G 1, G 1/2 and G 5/8 is no longer specified. Previous editions DIN 431: 1926-01, 1929-04, 1949xx-06, 1970-02, 1972-12, 1982-11, 2000-02. All dimensions are in millimetres.
Scope
This standard specifies dimensions and technical delivery conditions for sizes G 1/8 to G 6 (hexagon and octagon) pipe nuts with thread as in ISO 228-1 and of product grades B and C.
Normative references
This standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text, and the titles of the publications are listed below. For dated references, subsequent amendments to or revisions of any of these publications apply to this standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referred to applies. DIN DIN DIN DIN DIN DIN DIN 267-2 267-10 267-24 4000-2 EN 493 EN 10242 EN 28839 Fasteners Technical delivery conditions Product grades and tolerances Fasteners Technical delivery conditions Hot-dip galvanized components Fasteners Technical delivery conditions Property classes for nuts Tabular layouts of article characteristics for bolts, screws and fit bolts Fasteners Surface discontinuities Nuts Threaded pipe fitting in malleable cast iron Mechanical properties of fasteners Bolts, screws, studs and nuts made of nonferrous metals (ISO 8839 : 1986) Fasteners Acceptance inspection (ISO/DIS 3269 : 1998)*) Mechanical properties of corrosion-resistant stainless steel fasteners Part 2: Nuts (ISO 3506-2 : 1997) Fasteners Electroplated coatings (ISO 4042 : 1999) Tolerances for fasteners Part 1: Bolts, screws, studs and fit bolts Product grades A, B and C (ISO/DIS 4759-1 : 1997)*) Fasteners Non-electrically applied zinc flake coatings (ISO/DIS 10683 : 1999)*)
DIN EN ISO 3269 DIN EN ISO 3506-2 DIN EN ISO 4042 DIN EN ISO 4759-1 DIN EN ISO 10683
No part of this translation may be reproduced without the prior permission of DIN Deutsches Institut fr Normung e.V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany, has the exclusive right of sale for German Standards (DIN-Normen).
Page 2 DIN 431 : 2000-10 ISO 228-1 : 1994 Pipe threads where pressure-tight joints are not made on the threads Part 1: Designation, dimensions and tolerances ISO 8992 : 1986 Fasteners General requirements for bolts, screws, studs and fit bolts
Dimensions
Type A Type B For sizes G 1/ 8 to G 4 (hexagon) For sizes G 5 and G 6 (octagon)
Other dimensions as for type A Figure 1: Nut dimensions (types A and B) (notation) Table 1: Nut dimensions da Max. dw Min. e Min. Min. m Max.1) Max. =
nominal size
Thread size ( d)
s Min.
Bracketed sizes should not be used. 1) The maximum size applies for type B nuts. In the case of type A nuts, m is to be larger by a machining allowance. 2) The width across flats shall be included in the designation (cf. clause 5). 3) No values available.
Material General requirements Thread Mechanical properties Limit deviations and geometrical tolerances As specified in As specified in Property class1) As specified in Product grade As specified in
Steel
Nonferrous metal
A 2-50 DIN EN 28839. DIN EN ISO 3506-2. B for type B and C for type A DIN EN ISO 4759-1.
As processed.
Plain
Plain
Surface finish
DIN EN ISO 4042 applies with regard to electroplating. DIN EN ISO 10683 applies with regard to zinc flake coatings. DIN 267-10 applies with regard to hot-dip galvanizing. DIN 267-2 applies with regard to surface roughness. DIN EN 493 applies with regard to surface discontinuities. DIN EN ISO 3269 applies with regard to acceptance inspection.
Acceptance inspection
1)
Where nuts are to be made of other materials (except for malleable iron) or comply with other property classes, these shall be selected based on the relevant standards. Malleable iron nuts are to comply with DIN EN 10242.
5
Normen-Download-Beuth-VA TECH Hydro GmbH & Co-KdNr.6079052-LfNr.2846712001-2005-06-17 10:25
The designation of sizes G 1/8, G 1/4, G 1/2 and G 5/8 pipe nuts shall also include the the width across flats. EXAMPLE: Designation of a size G 1/2 pipe nut, type A, of property class 14H and with a width across flats of 34 mm (SW34):