CODE-PATI ?
FORMAT
First phase : 3 Questions of 2 Marks Second Phase : 3 Questions of 4 Marks Last phase : 2 Questions of 5 Marks Each
RULES
1. Minus points for wrong Answer 2. Question can be passed to the next team. 3. Question Answered Wrong cannot be Passed
FIRST PHASE
Questions of 2 Marks Each Each Team Answers 3 Questions Passed Question Next Team to Answer
Team 1
1
As per ASME Sec Viii Div 1,Min. Thickness of shells & heads of unfired steam boilers exclusive of corrosion allowance shall be ___mm?
1.6 6
2.4 3.2
Team 2
1 In which ASME Code Is P.No of a Material Specified
II A II D
II B Div 1
Team 3
1 For SA 516 Gr 70 material, 70 Denotes the following (In ksi )
Team 1
2 As per fig. UW-3 of ASME Sec. VIII Div 1 Nozzle to Vessel joints fall under which category
A C
B D
Team 2
2 As per fig. UW-3 of ASME Sec. VIII Div 1 Shell circ. Seam falls under which category
A C B D
Team 3
2
As per fig. UW-3 of ASME Sec. VIII Div 1 Hemi Head Crown to Petal Seam falls under which category
A C
B D
Team 1
3 L Grade in SS material stands for
Low Carbon
lateral
Team 2
3 Which ASME/ANSI STANDARD gives dimensions for Butt Welded Long Radius Elbows
B16.5 B16.20
B16.28 B16.9
Team 3
3 Which is the applicable Year of Edition for ASME B 16.5 as per ASME Sec. VIII Div. 2007
2007 1996
2003 2005
SECOND PHASE
Questions of 4 Marks Each Each Team Answers 3 Questions Passed Question Next Team to Answer
Team 1
1 Mininimum PWHT temperature for SA 387 Gr 22 Cl. 2 material as per ASME SEC VIII DIV 1 is _____ deg. C
691 675 650 710
Team 2
1 Mininimum PWHT temperature for SA 537 Cl. 2 material as per ASME SEC VIII DIV 1 is _____ deg. C
710 691
650 595
Team 3
1 Mininimum PWHT temperature for SA 533 Gr. B Cl. 2 material as per ASME SEC VIII DIV 1 is _____ deg. C
710 630
650 595
Team 1
2
Minimum staggering between Longitudinal seam of adjacent shell courses as per ASME SEC. VIII DIV 1
3t 4t
8t 5t
Team 2
2 For a carbon steel Hemi-Head % Extreme fibre Elongation is ___ x t/Rf
50 20
75 40
Team 3
2 For a carbon steel straight cone % Extreme fibre Elongation is ___ x t/Rf
50 20
75 40
Team 1
3 Saddle analysis when performed as per PD:5500, is covered under Annex -
L D
G M
Team 2
3 Factor of Safety in Design By AD Merkblatter code is
2.4 1.5
3 3.5
Team 3
3 Nozzle Reinforcement pads in an equipment designed as per ASME Sec. VIII Div. 2 can have max. thickness t = ___ x ts
1.3 1.2 1.5 2
LAST PHASE
Questions of 5 Marks Each Each Team Answers 2 Questions Passed Question Next Team to Answer One Life line available ask the expert (MV\MVA\NRR) Each expert to take one question only.
Team 1
1
For UT examination of plates as per SA 435 of ASME Sec. II A, supplementary requirement S1 stands for
SS Matl UT
100% Scan
Clad plate
10% Defect
Team 2
1 Carbon steel plate clad with _____ material is covered under SA 263 of ASME Sec. II A
SS304 SS410
SS316L Titanium
Team 3
1 For which of the following material allowable stress values vary with thickness
SA 516 SA 537
SA 533 SA 266
Team 1
2 HYDROTEST Multiplication Factor for Piping Code ASME B 31.3 is ___
1.3 1.5
1.25 1.43
Team 2
2 As per SA 20 of ASME Sec II A, grain size number ____ is considered to be fine austenitic grained material
>5 2
1 4
Team 3
2
For a Weld end of a Weld Neck flange procured as per ASME B16.5 as given in the figure below. The maximum value of 'T' is
12 6
19 25
Awards
CODE-PATI will be Announced