After making changes to the router, you issue the “copy running-config
startupconfig” command to save changes. After reloading the router, the router
comes up in setup mode. You again make changes, save them, and reboot. Again,
the router comes up in setup mode. What is the most likely cause of this?
Question2)
After working all night and successfully configuring a Cisco router for the HCL
network you save your changes on the startup config, reboot the router, and go out
for a cigarette. When you return, none of your changes are active and the router
boots to the initial configuration mode! Which of the choices below indicates the
source of your problem?
A. Hardware failure in NVRAM prevents the router from loading the config
Question3)
An access list was written with the four statements shown in the graphic. which
single access list statement will combine all four of these statements into a single
statements that will have exactly the same effect?
A. access-list 10 permit 172.29.16.0 0.0.0.255
Question4)
You need to troubleshoot a Cisco router at the U.K. office of hcl.com. The router
loses its configuration each time it is rebooted. You study the output displayed in
the exhibit. What is the cause of the problem?
Question5)
You are troubleshooting a frame relay connection and wish to view the LMI traffic
stats. Which command should you issue?
You are the network administrator at HCL. You need to perform password
What must you modify in the password recovery process? (Choose two.)
A. Configuration register
B. NVRAM
C. Boot flash
D. CMOS
Question7)
Which of the following can be an expected outcome of a VLAN? (Select all that
apply)
Three TK routers are configured for OSPF area 0 as shown in the diagram
below:
You wish to ensure that router TK2 will be preferred as the designated router (DR)
What configuration tasks could be used to establish this preference? (Choose all
that apply)
A. Configure the priority value of the Fa0/0 interface of RouterTK2 to a higher value
than any other interface on the Ethernet network.
B. Change the router id for Router TK2 by assigning the IP address 172.16.1.130/24
to the Fa0/0 interface of RouterTK2.
D. Change the priority values of the Fa0/0 interfaces of RouterTK1 and RouterTK3 to
zero.
Question9)
Which two are NOT characteristics of the OSPF routing protocol? (Select all that
apply)
C. It supports VLSM
Question10)
Which of the following Frame-Relay encapsulation commands would you use, if you
had to connect your Cisco router to a non-Cisco router?
Question11)
An ISDN link can be encapsulated using either PPP or HDLC. What are the
C. PPP will run faster and more efficiently than HDLC on circuit-switched ISDN links
In a lab, two routers are connected directly together using serial interfaces in a
back-to-back configuration. No external DCE devices are being used. What
additional command is needed to bring this link up?
A. serial up
B. clockrate
C. clock rate
D. dce rate
Question13)
Question14)
A. RouterTK(config-line)# access-class 10 in
Question15)
Which of the following steps are necessary in order to add a new VLAN to a
Question16)
You need to configure a single router into load balancing traffic across 4 unequal
cost paths. Which routing protocols can satisfy this requirement? (Select two)
A. RIP v1
B. RIP v2
C. IGRP
D. EIGRP
Question17)
A host computer has been correctly configured with a static IP address, but the
default gateway is incorrectly set. Which layer of the OSI model will be first affected
by this configuration error?
A. Layer 1
B. Layer 2
C. Layer 3
D. Layer 4
Question18)
When designing OSPF networks; what is the purpose of using a hierarchical
B. To speed up convergence
Question19)
You are the network administrator at TestKing. You apply the following access list on
the E0 outbound interface connected to the 192.168.1.8/29 LAN: access-list 21 deny
tcp 192.168.1.8 0.0.0.7 eq 20 any access-list 21 deny tcp 192.168.1.8 0.0.0.7 eq 21
any What will the effect of this access list be?
A switch has been configured for three different VLANs: VLAN 2, VLAN 3, and
added. Host from one VLAN should be able to reach the hosts in the other VLANs.
and switch?
A. 10 Mbps Ethernet
B. 56 kbps serial
If a host on a network has the address 172.16.45.14/30, what is the address of the
subnetwork to which this host belongs?
A. 172.16.45.0
B. 172.16.45.4
C. 172.16.45.8
D. 172.16.45.12
Question22)
As a HCL trainee you are required to set the default gateway on a Cisco switch to
the IP address of 192.168.1.115. Which IOS command should you use?
Question23)
HCL has 25 computers and decides to connect the network to the Internet. HCL
would like for all of the computers to have access to the Internet at the same time,
but HCL only has four usable publicly routable IP addresses. What should be
configured on the router so that all computers can connect to the Internet
simultaneously?
A. Static NAT
B. Global NAT
C. Dynamic NAT
Question24)
You are securing a network for HCL and want to apply an ACL (access control list) to
an interface of a router. Which one of the following commands would you use?
Question25)
You have a network that supports VLSM and you need to reduce IP address waste in
your point to point WAN links. Which of the masks below would you use?
A. /38
B. /30
C. /27
D. /23
Question26)
What should be done prior to backing up an IOS image to a TFTP server? (Choose
three)
A. Make sure that the server can be reached across the network.
C. Assure that the network server as adequate space for the IOS image.
Question27)
What information is supplied by CDP?(multiple answer)
A. Device identifiers
B. Route identifier
C. Capabilities list
D. Platform
Question28)
On the topic of the OSPF hello protocol; which of the statements below are true?
D. The OSPF Hello protocol negotiates the correct parameters between neighboring
interfaces.
Question29)
Which encapsulation types are configurable on a Cisco switch for a trunk? (Select
A. VTP
B. ISL
C. CDP
D. 802.1Q
Question30)
You are a senior network administrator at TestKing, and while performing the
password recovery procedure on your 2500 series Cisco router, you type in the
following command: o/r 0x2142 What is the purpose of this command?
Question31)
Which layer of the OSI reference model is responsible for ensuring reliable end-
toend delivery of data?
A. Application
B. Presentation
C. Session
D. Transport
Question32)
following display:
Refer to the partial Command output shown. Which two statements are correct
Question33)
Which of the following are true statements regarding the characteristics of OSPF
Question34)
After making some network changes you power off and then power on your Cisco
router. What sequence of events occurs when a router is powered up?
B. Locate Cisco IOS software, load Cisco IOS software, locate configuration
statements, apply configuration statements, and perform POST.
C. Test software routines, POST, load configuration files, load Cisco IOS software,
test Cisco IOS software.
D. POST, locate Cisco IOS software, load the Cisco IOS software, locate configuration
statements, and apply configuration statements.
Question35)
All of the hosts in the above exhibit are connected with each other via the single
Catalyst switch. Which of the following statements correctly describe the addressing
Question36)
Which of the routing protocols shown below support both VLSM and route
A. IGRP
B. EIGRP
C. RIP v2
D. OSPF
Question37)
What kind of information can you deduce from an IOS image file name? (Select
A. Feature capabilities
Question38)
Which of the following can LCP successfully negotiate during the establishment of a
A. Q.931
B. multilink
C. CHAP
D. callback
Question39)
You wish to upgrade the IOS of a router without removing the image currently
installed. What command will display the amount of memory that is being used by
the current IOS image and whether there is enough room available to hold both the
current and new images?
Question40)
In the context of configuring dial-on-demand routing using ISDN, what is the
purpose of the dialer-list command?
Question41)
In the above network, an access list was created in order to prevent students and
outsiders on the internet from changing student files in the Records Server, while
still allowing other departments in the enterprise access. The access control list was
applied to the e0 interface of the TestKing 3 router going outbound. Which two of
the following conditions below were contained in the access control list? (Select two
answer choices)
Question42)
that VLAN information will be automatically distributed to all the other Cisco
Which of the conditions below have to be met in order for this to occur? (Choose all
that apply)
A. The switch that will share the VLAN information must be in the VTP Server mode
D. The switch that will share the VLAN information must be configured as the root
bridge.
Question43)
On the Hong Kong router an access list is needed that will accomplish the following:
1. Allow a Telnet connection to the HR Server through the Internet
Which of the following access list statements are capable of accomplishing these
Question44)
You have just purchased a brand new router and wish to have the router prompt you
through the initial configuration commands. Which router mode does this describe?
B. SETUP mode
C. Autoflash mode
D. RXBOOT mode
Question45)
Which of the following commands will display the name of the IOS image file being
Question46)
The MAC address for your PC NIC is: C9-3F-32-B4-DC-19. What is the address of the
OUI portion of this NIC card, expressed as a binary number?
A. 11001100-00111111-00011000
B. 11000110-11000000-00011111
C. 11001110-00011111-01100000
D. 11001001-00111111-00110010
Question47)
You are bringing up a new Cisco Catalyst switch, and wish to connect it via a trunk
to another switch from a different vendor, which uses the IEEE standard for the
trunking method. When setting the encapsulation type on the trunk, what should
you configure on the Cisco switch?
Question48)
A. Point-to-point
B. Point to multipoint
C. Broadcast
D. Non-broadcast multi-access
Question49)
After logging into a router and typing in a few show commands, you press the up
arrow key. What will this do?
Question50)
You are in the midst of configuring a router for a Frame Relay network. What
could you do to prevent split horizon problems? (Select all that apply)
A. Configure a separate sub-interface for each PVC. Assign a unique DLCI and
subnet to each sub-interface.