1 3 4. Essential features
GSM Click with its Telit GL865-QUAD IC is ideal for mobile devices. It features GSM/GPRS protocol stack 3GPP (release 4 compliant) and supports GSM/GPRS 850/900/1800/ 1900 MHz Quad-band frequency. Additional features such as integrated TCP/IP protocol stack (including UDP, SMTP, ICMP and FTP), serial multiplexer, remote AT commands and many more, extend the functionality of the board.
GSM click
1. Introduction
Turn the board upside down so that bottom side is facing you upwards. Place shorter parts of the header pins in both soldering pad locations.
Turn the board upward again. Make sure to align the headers so that they are perpendicular to the board, then solder the pins carefully.
GSM Click is an add-on board in mikroBUS form factor. Its a compact and easy solution for adding GSM/GPRS mobile phones standard to your design. It features GL865-QUAD GSM/ GPRS module, TXB0106 6-bit bidirectional voltage-level translator as well as SIM CARD socket. GSM Click communicates with target board microcontroller via seven mikroBUS lines (RX, TX, INT, PWM, CS, RST and AN). The board is designed to use 3.3V and 5V power supply. LED diode indicates the presence of power supply.
click
www.mikroe.com
GSM click Manual
ver. 1.01
BOARD
0 100000 022238
6. SMD Jumper
VCC R2 220 LD2 R3 1K U1 24 23 22 21 20 19 18 17 16 15 14 13 MIC+ C1 100nF EAR+ STAT_LED R5 1K R6 100K AGND +2V8 R7 2K2 MIC+ EAR+ E1 E2 10uF 10uF CN3 R4 100K
36 35 34 33 32 31 30 29 28 27 26 25
LD3
TX_LED
Q1 BC846
+2V8 1 2 3 4 5 6 7 8
A1 VCCA A2 A3 A4 A5 A6 OE
B1 VCCB B2 B3 B4 B5 B6 GND
16 15 14 13 12 11 10 9
100nF
U2
VCC
!GPIO2 GPIO1
GL865-QUAD
+2V8
37 38 39 40 41 42 43 44 45 46 47 48
Vgsm
Q2 BC846
There is one zero-ohm SMD jumper J1 which is used to select whether 3.3V or 5V power supply is used. Jumper J1 is soldered in 3.3V position by default.
TXB0106
!RST
7. Code Examples
Once you have done all the necessary preparations, its time to get your click board up and running. We have provided the examples for mikroC, mikroBasic and mikroPascal compilers on our Libstock website. Just download them and you are ready to start.
1 4 3 2
C2
C8 100nF
7 8 9 10 11 12
1 2 3 4 5 6
TXB0106
ST-328B-3 AGND
VCC
!TXD !RXD SIM_VCC SIM_RST SIM_CLK SIM_IO !RTS !CTS
Vgsm
VCC FP1
E4 470uF/10V E3 470uF/10V
R8 4K7 PWRMON +2V8 R9 1K R11 100K Q3 BC846 SIM_VCC SIM_RST SIM_CLK SIM_IO
33pF 33pF
C6 100nF
E5 10uF
1 2 3 7
33pF
.com 8. Support
8 4 5
C3
C5
C4
RST
R12 1K
SIM_CARD
4
Pin Number Description 1 Left Audio 2 Right Audio
3
3 Microphone
2
4
MikroElektronika offers Free Tech Support (www.mikroe.com/esupport) until the end of product lifetime, so if something goes wrong, we are ready and willing to help!
Common/GND
MikroElektronika assumes no responsibility or liability for any errors or inaccuracies that may appear in the present document. Specification and information contained in the present schematic are subject to change at any time without notice. Copyright 2012 MikroElektronika. All rights reserved.