DESCRIPTION
The Series CRV Relief Valve is engineered to address the specific needs of Cryogenic Liquid Cylinder and non-coded Thermal Safety Relief Valve applications. The High Flow and excellent reseal characteristics also make this valve ideally suitable for many industrial applications. Poppet design completely retains soft seal while providing a Metal-to-Metal back up. This poppet, combined with a burnished seat, insures repeatable performance even when subjected to repeated cycles at cryogenic temperatures. Valves are factory preset, 100% tested and supplied permanently locked to desired set point.
OPTIONS
Pipe-A-Way Adapter Tamper Proof Ring (ideal for liquid cylinders) Seal Materials Certified Test Results
CONSIDERATIONS
Standard Teflon seal (Teflon above 50 PSI), other seals available Cleaned for Oxygen Service Drain Hole provided on CRV & CRVT Drain Hole omitted on CRVP Flow is unaffected with 10% Back Pressure Permanently Stamped with Full P/N and Pressure Setting Can be supplied with Color Coded Labels in PSI and BAR No Mounting Limitations
SERIES CRV
PIPE SIZE 19/32 7/8 HEX 2-1/2 FLOW OPTIONAL LABEL B SIZE A B 1/4 NPT 11/32 7/8 3/8 NPT 11/16 7/8 1/2 NPT 3/4 1
TECHNICAL DATA
Inlet Orifice: .312 Diameter Flow Coeficient: .45 @ 110% of Nominal Set Pressure Full Rated Flow is achievd by 110% of Nominal Set Pressure Crack Pressure Tolerance: +/- 5% of Nominal Set Pressure Zero Leakage up to 95% of Nominal Set Pressure Temperature Range: -320 to +400 Fahrenheit Proof Pressure: 1500 PSI Brass Bar Stock Construction with Stainless Steel Springs
ORDERING INFORMATION
CRV 250B T
SERIES CRV - Cryogenic Relief Valve CRVP2 - Cryogenic Relief Valve with 1/4 Female Pipe-A-Way Adapter Installed CRVP3 - Cryogenic Relief Valve with 3/8 Female Pipe-A-Way Adapter Installed CRVP4 - Cryogenic Relief Valve with 1/2 Female Pipe-A-Way Adapter Installed CRVT - Cryogenic Relief Valve with Tamper Proof Ring Installed CRVD - Cryogenic Relief Valve with Deflector Adaptor Installed (not shown above)
350
NOMINAL SET PRESSURE Specify 10 - 750 PSI SEAL MATERIAL T - Teflon (above 50 PSI) FS - Fluorosilicone V - Viton
INLET PIPE SIZE(NPT) 250B - 1/4 Male, Brass 375B - 3/8 Male, Brass 500B - 1/2 Male, Brass
GENERANT
1865 Route 23 South PO Box 768 Butler, New Jersey 07405 www.generant.com Phone 973.838.6500 Fax 973.838.4888
SERIES CRV
Considerations
When sizing a Relief Valve, ASME recommends using 90% of published data For use on Liquid Cylinders, Series CRV Valves exceed flow requirements set forth in CGA S1.1 Spring Range vs. Discharge Coefficient (Kd) listed on back of this page
GENERANT
1865 Route 23 South PO Box 768 Butler, New Jersey 07405 Phone 973.838.6500 www.generant.com Fax 973.838.4888
SERIES CRV
Spring Range vs. Discharge Coefficient Spring CRV-4-250-22 CRV-4-250-35 CRV-4-250-50 CRV-4-250-75 CRV-4-250-100 CRV-4-250-150 CRV-4-250-230 CRV-4-250-350 CRV-4-250-500 Valve Orifice .312 Diameter Lower 20.5 29 46 63 90 131 181 276 401 Upper 28 45 62 89 130 180 275 400 615 Kd 0.59 0.59 0.59 0.54 0.42 0.35 0.25 0.12 0.18
GENERANT
1865 Route 23 South PO Box 768 Butler, New Jersey 07405 Phone 973.838.6500 www.generant.com Fax 973.838.4888