USA-E99971-155-*
unit (rotary switchs and 7 segment LED, up-side of unit) Normal operation mode setting segment LED display
SW1
ON
OFF
Each mode setting Power ON : execute
Li Battery
Setting
reerved reerved reerved reerved backup reerved e restore reerved ther IP reerved e reerved mode NC reerved reerved reeved reerved reerved
Description Normal operation modesetting of Ship Not usedEthernet communication stop User stop ReservedNot used ReservedNot used ReservedNot used ReservedNot used Offline monitor SRAM backup to ATA card ReservedNot used Clear SRAM (PowrONF0 display) SRAM restore from ATA card address displays on 7seg. C0A80102 IP: 192.168.1.2 C00000000 GW: 0.0.0.0 FFFFFF00 NM:255.255.255.0 FCF6(repeat from first) Port:64758 Check displays, switch CS1:9 Then initialize starts:finished Check Cr displays, switch CS1:9 Then address initialize activate ReservedNot used ReservedNot used ReservedNot used ReservedNot used MDS S/W download mode, S/W selectCS2 ReservedNot used starts MDS S/W download
O NC SYSTEM download to temporary ram PO NC SYSTEM write to F-ROM O Finished (compare OK)
Power OFF C64, take off MASTER ROM cassette from slot, puts cover to slot. Then change setting of rotary switch to CS1:0, CS2:0, SW1:OFF Power ON C64 and check the version of NC DIAG/ALMMENU
Displays S/W system number which selected by CS2 Example:directory number (CS2 setting) is & S/W system number is BND-456W123-ABC Display blankblankblank blankblankblank ABblankCblankrepeat from first If setting of CS2 is changed, then display number changes as the new selected system number, too. C64 Amp. status Connection check Erase Amp. F-ROM L L S/W download Pr Pr Write Amp. F-ROM Compare Version up normally done
Backup datas Backup NC datas by RS232C or SRAM backup. The backup operation of RS232C is written in Section 5. Dont forget data compare when using RS232C. Replace whole NC unit or HR851 card Replace whole NC unit or HR851 card only. After replace, do S-RAM initialize (CS1:7 then Power ON) Dont forget to change CS1:0 after initialize. Restore NC datas The restore operation of RS232C is written in Section 5. Attention1 When using RS232C, you must setup I/O parameter, and NC file format operation, too. Sec. Attention2 If you using SRAM backup, I/O param. setting and NC file format is not necessary.Sec. Attention3 If CE-TERMINAL is attached C64, you can backup datas by CE-TERMINAL DataI/O to ATA card too. Sec.
Power OFF and rotate NC rotary switch CS1:5, SW1:ON, CS2:0F. If CS2 sets to 0, then ATA card will be format and SRAM data writes to \C64back0.dat. If CS2 sets to 1 then SRAM data writes to \C64back1.dat. Puts ATA card into NC IC CARD slot. Power ON NC. If CS2 sets to 0, then display changes to F. If you want to format ATA card, change CS1 as 545 then ATA card format starts. Or if already file is exists, display changes to dP. If you want to overwrite file, change CS1 as 545 then SRAM data writes to ATA card. After display changes to Fn, power off and chage rotary switch to CS1:0 CS2:0 SW1:OFF. SRAM restore Operation
7 Segment display
Power OFF and rotate NC rotary switch CS1:7, SW1:ON, CS2:0F If CS2 sets to 0, then file \C64back0.dat will be used to Restore SRAM. If CS2 sets to 1, then file \C64back1.dat will be used. Puts ATA card into NC IC CARD slot. Power ON NC Automatically data restore to SRAM After display changes to Fn, power off and chage rotary switch to CS1:0 CS2:0 SW1:OFF.