www.huawei.com
Copyright © 2006 Huawei Technologies Co., Ltd. All rights reserved. Page2
Basic Property
Basic property
SACCH Multi-Frames
Paging Times
Max TA
T3105
Copyright © 2006 Huawei Technologies Co., Ltd. All rights reserved. Page3
SACCH Multi-Frames
Range:0~63
Unit: SACCH period (480ms)
Default:14
Description: It is a timer used to determine whether the uplink radio link
connection fails. BSS judges the uplink radio link failure according to
uplink SACCH BER. (See Protocol 0508, 0858, and 0408.) Every time
BTS fails to decode the MR sent from MS, this timer decreases by 1; and
every time BTS succeeds to decode the MR, this timer increases by 2.
When this timer reaches 0, BTS judges that the uplink radio connection
fails. Then BTS sends a radio connection failure message to BSC. This
parameter and the radio link timeout (RLT) are used to judge the
uplink/downlink radio connection failure.
Copyright © 2006 Huawei Technologies Co., Ltd. All rights reserved. Page4
Paging Times
Range:1~8(BTS3X)
Unit: times
Default:1
Copyright © 2006 Huawei Technologies Co., Ltd. All rights reserved. Page5
Max TA
Range:
0~63 (Normal cell).
0~255 (Dual TS extended cell).
Unit: bit period (1 bit = 0.55km)
Default:
62 for normal cell,
219 for dual TS extended cell.
Description: Maximum Time Advance. It determines the actual
coverage area of BTS. When BTS receives the channel request
message, it determines whether channel assignment should take place
in the current cell by comparing the TA with the value of this parameter.
Copyright © 2006 Huawei Technologies Co., Ltd. All rights reserved. Page6
Max Resend Times of Phy. Info.
Range:1–255
Unit: times
Default:30
Description: This parameter specifies the maximum times Ny1
for re-sending physical information. If the number of resending
times exceeds Ny1 and BTS still has not received any correct
SAMB frame from MS, BTS will send BSC the connection
failure message and handover failure message. After BSC
receives the messages, it will release the assigned dedicated
channel and stop timer T3105.
Copyright © 2006 Huawei Technologies Co., Ltd. All rights reserved. Page7
T3105
Range:0–255
Unit:10 ms
Default:7
Description:T3105 is a timer for radio connection. See the
description of Max resend times of Phy. Info.
Copyright © 2006 Huawei Technologies Co., Ltd. All rights reserved. Page8
Cell Extension
Cell extension
Cell Extension Type
Copyright © 2006 Huawei Technologies Co., Ltd. All rights reserved. Page9
Cell Extension Type
Range: Normal cell, Dual timeslot extended cell
Copyright © 2006 Huawei Technologies Co., Ltd. All rights reserved. Page10
Timer
Timer
T200
N200
Copyright © 2006 Huawei Technologies Co., Ltd. All rights reserved. Page11
T200 and N200
Description:
T200 timers are used to avoid deadlock during data transfer on the data link
layer.
On the LAPDm layer, every time a message is sent, the opposite end is
requested to acknowledge the reception. If this message is lost for unknown
reasons, it will occur that both ends keep waiting, leading to system deadlock.
Therefore, a timer should be started when the sender sends a message. If the
timer times out, the sender will regard that the receiver has not received the
message and will resend the message.
The maximum resend times are determined by N200.
Different timer values should be set for different LAPDm channels such as
SDCCH, FACCH and SACCH. This is because these channels have different
transmission rate.
Copyright © 2006 Huawei Technologies Co., Ltd. All rights reserved. Page12
Use LAPDm N200
Range: Yes, No
Default: No
Copyright © 2006 Huawei Technologies Co., Ltd. All rights reserved. Page13
Interference Band
Interference band
Interference Band Threshhold
Copyright © 2006 Huawei Technologies Co., Ltd. All rights reserved. Page14
Interference Band Threshold 0~5
Value range: 110~85
Unit: -dBm
Content: It decides the corresponding value for each interference
band (from band 0 to band 5) and used to measure the uplink
interference during the TCH timeslot is in idle mode.
Recommended values:
110 ( Interference band threshold 0)
105 ( Interference band threshold 1)
98 ( Interference band threshold 2 )
90 ( Interference band threshold 3 )
87 ( Interference band threshold 4 )
85 ( Interference band threshold 5)
Copyright © 2006 Huawei Technologies Co., Ltd. All rights reserved. Page15
Call Control and Processing Parameters
Call control and processing parameters are in Cell Call
Control Table and Cell Call Control Parameter Table
TCH immediate assignment
Direct Retry
Copyright © 2006 Huawei Technologies Co., Ltd. All rights reserved. Page16
TCH Immediate Assignment
Range: Yes, No
Default: No
Copyright © 2006 Huawei Technologies Co., Ltd. All rights reserved. Page17
Immediate Assignment Optimization
Range: Yes, No
Default: No
Copyright © 2006 Huawei Technologies Co., Ltd. All rights reserved. Page18
Direct Retry
Range: Yes, No
Default: Yes
Copyright © 2006 Huawei Technologies Co., Ltd. All rights reserved. Page19
Assignment Cell Load Judge Enabled
Range: Yes, No
Default: Yes
Copyright © 2006 Huawei Technologies Co., Ltd. All rights reserved. Page20
Cell Direct Try Forbidden Threshold
Range: 0–6
Default: 5
Copyright © 2006 Huawei Technologies Co., Ltd. All rights reserved. Page21
Directed Retry Load Access Threshold
Range: 0–6
Default: 5
Copyright © 2006 Huawei Technologies Co., Ltd. All rights reserved. Page22
Thank you
www.huawei.com