|CH|
Q. No. 1 10 Carry One Mark Each 1. Pick out the correct statement about Bernoulli equation of the following? (A) It is applicable for creeping flow (B) It is applicable for potential flow (C) It is a total energy balance equation (D) All of these 2. It the viscosity of a gas at Po is 0 and P1 is 1 , if P0 < P1 , then
(A) 0 < 1
3.
(B) 1 > 0
(C) 1 = 0
Consider a liquid, which is in static condition in the container. Consider a point P within the fluid as shown below. If Px , Py , P2 are the pressure components in x, y and z directions respectively, then
10m
5m 6m
of these
4.
Match the following with the lists given below. List-I (P) Pseudoplastic (Q) Newtonian (R) Dilatant (A) P 1, Q 1, R 1 List-II (1) Time independent (2) Time dependent
(B) P 2, Q 2, R 2 (D) P 2, Q 1, R 2
(C) P 1, Q 2, R 1
5.
The nature of shape of fluid in a centrifugal bowl is (A) Cylinder (B) Parabolic (C) Both (A) & (B) (D) None of these
6.
Consider a column of liquid as shown below and determine the relation between P1 , P2 , and P3 .
(A) P1 P2 P3
Correspondence Course
without the written permission.
(B) P1 = P2 P3
TarGATE
(C) P1 P3 = P1
(D) P1 P2 = P3
eTutor Online Test Series
69
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form
CHFLMC004 7.
|CH|
For the application of Bernoullis theorem to a curved tube, nature of the velocity to be used changes from (A) Scalar to vector (C) Vector to scalar (B) Remains constant (D) None of these
8.
For which of the following, Bernoullis equation can be applied (A) Free liquid jet (C) Both (A) & (B) (B) Radial flow (D) None of these
9.
If rP , rN and rD are skin values of shear stresses at a particular velocity gradient from pseudoplastic, Newtonian and dilatant liquids respectively, choose the accurate relation between them.
Bingham Pisudoplastic
Newtonian
r
Dilotam
du dy
10.
Which of the following represents the approximate range of values of absolute viscosities of liquids? (A) Liquids near wiling point and polymer melts (B) Liquids and polymers (C) Liquid metals and polymers (D) None of these
11.
What are the possible final temperatures of two fluids, if heat generated per unit volume is same for both the liquids, assuming that their densities are in the ratio 2:1, where as the specific heats are in the ratio of 2 : 1 and initial temperatures of fluids is 90OC.
(A) 92,100
Correspondence Course
without the written permission.
(B) 91, 92
TarGATE
(D) 92, 98
eTutor Online Test Series
70
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form
CHFLMC004 12.
|CH|
If we assume real gas for the derivation for Bernoulli equation, then the value of Pb Pa b (A) Will decrease (B) Will increase (C) Will remain constant (D) None of these
13.
Which of the following statements is incorrect? (A) The interface is vertical in this zone (B) The force of gravity = centrifugal force (C) The force of gravity << centrifugal force (D) None of these
14.
du (1) 3 106 dy
0.59
1.5
(A) P 1, Q 3, R 2 (C) P 3, Q 2, R 1
15.
Which of the following statements are correct for the power consumption in pseudoplastic fluids?
No power number
10
newtonian
bseudoplastic Re
100
i.e,
(A) For R C < 10 , it will be equal to the power consumed by Newtonian fluids (B) For R e > 100, it will be equal to the power consumed by Newtonian fluids (C) Both (A) & (B) (D) None of these
Correspondence Course
without the written permission.
TarGATE
eTutor
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form
CHFLMC004
16.
|CH|
The ratio of times of separation, in a decanter for two liquid systems having same 2 continuous phase, if the lighter liquid density is of heavier liquid density in first 3 1 or heavier liquid density is system where as in second system it is 3
(A) 1.2
(B) 2 : 1
(C) 1 : 1
17.
(A)
x y
(B) x y
(C)
y x
(D)
1 xy
18.
(A) x2 + y2
(B) y2 x2
(C) xy
(D)
y x
19.
(A) 30 Pa
(B) 20 Pa
(C) 10 Pa
(D) 15 Pa
20.
If the plate moves with velocity of 0.5 m / s instead of 1m/s, then the shear stress acting on the plate will be
(A) 25kPa
(B) 15kPa
(C) 5kPa
(D) 10 kPa
Correspondence Course
without the written permission.
TarGATE
eTutor
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form