Product Bulletin
Code No. LIT-12011182
Issued April 18, 2006
Introduction
The S300 Series add-on reader and input/output (I/O) modules are designed to expand the quantity of portal and I/O devices controlled by CK721, CK720, or CK705 controllers. Portal devices typically consist of readers, Request to Exit (REX) devices, door contacts, and door strikes or magnetic locks. I/O devices typically consist of alarm input devices, such as sensors, and annunciation devices, such as a sounder or strobe light. Johnson Controls, Inc. offers the following reader and I/O modules: S300-RDR2 Reader module that controls two fully configured doors. See Figure 1. S300-SI8 Input module with eight supervised (4-state) inputs. S300-SIO8 Input/Output module with eight supervised (4-state) inputs and eight outputs. S300-IO8 Input/Output module with eight unsupervised (2-state) inputs and eight outputs. S300-I16 Input module with 16 unsupervised (2-state) inputs.
RDR2 Module
S300-SI8
8 Yes Yes -
S300-SIO8
8 8 Yes Yes -
S300-IO8
8 8 No Yes -
S300-I16
16 No Yes -
S300-RDR2
No Yes 2
The S300-RDR2 also provides two door input/output interfaces each consisting of: A two-state door monitor switch input (secure = normally closed) A two-state auxiliary access or exit request switch input (normally open) A door-strike relay (SPDT) An alarm shunt relay driver (open collector)
Description
Reader 1 Connector Reader 1 Keypad Connector Reader 1 Two-Wire Wiegand Reader Interface Connector Reader 2 Connector Reader 2 Keypad Connector Reader 2 Two-Wire Wiegand Reader Interface Connector RS-485 Input RS-485 Output Determines Reader Address Indicates when data is transmitted or received and the presence of 5 and 12 VDC S300-RDR2 Firmware
U4
Wattage (W)
4.55
2.63
Each Reader Interface provides +5VDC, +12VDC, SHUNT Output, RED Output, and GREEN Output. The current loading on these outputs must be derived from the reader manufacturers data sheet and added to the total load. Note +5VDC is current limited to operate Cardkey Readers (20 mA).
Description
RS-485 Input RS-485 Output Alarm Inputs 1 and 2 Alarm Inputs 3 and 4 Alarm Inputs 5 and 6 Alarm Inputs 7 and 8 Address Settings Indicates when data is transmitted or received and the presence of 5 and 12 VDC S300-SI8 Firmware
U1
Wattage (W)
2.82
All other functions, including the eight output relays, are identical to the S300-IO8 module. Table 6: S300-SIO8 Components Component
J1A J1B J1C J1D J2A J2B J2C J2D J3 J4 J6A J6B J6C J6D SW1 System LEDs
Description
Output Relay 1 Connector Output Relay 2 Connector Output Relay 3 Connector Output Relay 4 Connector Output Relay 5 Connector Output Relay 6 Connector Output Relay 7 Connector Output Relay 8 Connector RS-485 Input RS-485 Output Alarm Inputs 1 and 2 Alarm Inputs 3 and 4 Alarm Inputs 5 and 6 Alarm Inputs 7 and 8 Address Settings Indicates when data is transmitted or received, and the presence of 5 and 12 VDC S300-SIO8 Firmware
U1
Wattage (W)
5.34
Description
Output Relay 1 Connector Output Relay 2 Connector Output Relay 3 Connector Output Relay 4 Connector Output Relay 5 Connector Output Relay 6 Connector Output Relay 7 Connector Output Relay 8 Connector RS485 Input RS485 Output Alarm Inputs 1 and 2 Alarm Inputs 3 and 4 Alarm Inputs 5 and 6 Alarm Inputs 7 and 8 Address Settings Indicate when data is transmitted or received and the presence of 5 and 12 VDC S300-IO8 Firmware
U1
Wattage (W)
3.54
Description
Alarm Inputs 9 and 10 Alarm Inputs 11 and 12 Alarm Inputs 13 and 14 Alarm Inputs 15 and 16 RS-485 Input RS-485 Output Alarm Inputs 1 and 2 Alarm Inputs 3 and 4 Alarm Inputs 5 and 6 Alarm Inputs 7 and 8 Address Settings Indicate when data is transmitted or received and the presence of 5 and 12 VDC S300-I16 Firmware
U3
Wattage (W)
1.19
Technical Specifications
Table 12: Technical Specifications Description
Weight Dimensions Ambient Storage Temperature Ambient Operating Temperature Relative Humidity (Operating) Relative Humidity (Non-operating) SPDT Relay Contact Rating
Ordering Information
Table 13: Ordering Information Part Number
S300-RDR2 S300-SI8 S300-SIO8 S300-IO8 S300-I16
Specification
6.6 ounces (187 grams) 5W x 5L inches (12.7W x 12.7L cm) -40 to 158F (-40 to 70C) 0 to 50F (-18 to 10C) 20 to 80%, non-condensing 5 to 95%, non-condensing 2 A @ 24 VDC
Description
Reader module that supports two fully configured doors Module with eight 4-state (supervised) inputs Module with eight 4-state (supervised) inputs and eight outputs Module with eight 2-state (unsupervised) inputs and eight outputs Module with sixteen 2-state (unsupervised) inputs
Cardkey is a registered trademark of Johnson Controls, Inc. All other marks herein are the marks of their respective owners. 2006 Johnson Controls, Inc.
7
www.johnsoncontrols.com