The contents in this document are subject to changes, for improvement and other purposes,
without notice.
Be sure to check the delivery specifications before using these products. The operation and circuit examples in this document are provided for reference purposes
only. Sanken assumes no liability for violation of industrial property, intellectual property, or other rights of Sanken or third parties, that stem from these examples.
The user must take responsibility for considering and determining which objects the
products in this document are used with.
Although we will continue to improve the quality and reliability of our products,
semiconductor products, by their nature, have certain fault and failure rates. The user must take responsibility for designing and checking to secure the device and system so that a part failure may not lead to human injury, fire, damages, or other losses.
The products in this document are intended for normal electronic devices (such as home
appliances, office equipment, communication terminals, or measurement devices). If you are considering using our products for a device that requires high reliability (such as transport machines and their control units, traffic light control systems, disaster prevention, and security equipment or any kind of safety equipment), make sure that you consult our sales representative. Do not use these products for devices that require extremely high reliability (such as aerospace instruments, nuclear power control units, or life support systems).
The products in this document are not designed to be radiation-proof. The contents in this document must not be transcribed or copied without our written consent.
SANKEN SEMICONDUCTORS
C O N T E N T S
ICs
1-1 Power Management ICs ..................................................................................................... 6 1-1-1 1-1-2 1-1-3 1-1-4 1-2 Power Factor Correction (PFC) ICs ................................................................... 6 AC/DC Converter ICs .......................................................................................... 6 DC/DC Converter ICs ........................................................................................ 10 Linear Regulator ICs .......................................................................................... 64
Motor Driver ICs ................................................................................................................ 86 1-2-1 2-Phase Stepper Motor Unipolar Driver ICs .................................................... 90 1-2-2 1-2-3 1-2-4 1-2-5 1-2-6 3-Phase Stepper Motor Driver ICs ................................................................ 112 5-Phase Stepper Motor Driver ICs ..................................................................... 114 Brush DC Motor Driver ICs ................................................................................ 116 Low Voltage 3-Phase Brushless Motor Driver ICs ............................................. 118 High Voltage 3-Phase Brushless Motor Driver ICs ............................................ 120
1-3
Lighting ICs ..................................................................................................................... 142 1-3-1 LED Lighting ICs ............................................................................................. 142 1-3-2 Household HID Lamp Driver ICs ................................................................... 146
Transistors
2-1 2-2 2-3 2-4 Transistors ...................................................................................................................... 153 MOS FETs ....................................................................................................................... 163 IGBT ................................................................................................................................. 167 Transistors and MOS FET Arrays ................................................................................ 170
Thyristors
3-1 3-2 Thyristors ........................................................................................................................ 190 Triacs ............................................................................................................................... 192
Diodes
4-1 4-2 4-3 4-4 4-5 4-6 Rectifier Diodes .............................................................................................................. 203 Fast Recovery Diodes ................................................................................................... 204 Ultrafast Recovery Diodes ............................................................................................ 206 Schottky Barrier Diodes ................................................................................................ 209 Power Zener Diodes ...................................................................................................... 212 Silicon Varistors ............................................................................................................. 213
216
ICs
Ordering Information & Standard Packing Quantities ................ 4 1-1 Power Management ICs ........................................................... 6 1-1-1 1-1-2 1-1-3 Power Factor Correction (PFC) ICs ........................... 6 AC/DC Converter ICs .................................................. 6 DC/DC Converter ICs ................................................ 10 Selection Guide .......................................................... 10 Application Note ......................................................... 11 1-1-4 Linear Regulator ICs ................................................. 64 Selection Guide .......................................................... 64 Application Note ......................................................... 65 1-2 Motor Driver ICs ..................................................................... 86 Selection Guide ...................................................................... 86 Application Note ..................................................................... 89 1-2-1 1-2-2 1-2-3 1-2-4 1-2-5 1-2-6 1-3 2-Phase Stepper Motor Unipolar Driver ICs .......... 90 3-Phase Stepper Motor Driver ICs ......................... 112 5-Phase Stepper Motor Driver ICs ......................... 114 Brush DC Motor Driver ICs ..................................... 116 Low Voltage 3-Phase Brushless Motor Driver ICs .. 118 High Voltage 3-Phase Brushless Motor Driver ICs ... 120
Lighting ICs ........................................................................... 142 1-3-1 1-3-2 LED Lighting ICs ...................................................... 142 Household HID Lamp Driver ICs ............................ 146
1 ICs
Ordering Information
All products listed must be ordered in standard packing increments.
Series Name/ Product Name LC5200D LC5500D LC5500F NR885K SAI SCM1100M/ SCM1200M SI-3000KD SI-3000KF SI-3000KM SI-3000KS SI-3000KWM SI-3000LLSL SI-3000LSA SI-3000LU SI-3000ZD SI-3000ZF SI-7321M SI-7510 SI-8000E SI-8000FD SI-8000FFE SI-8000GL SI-8000HD SI-8000HFE SI-8000JD SI-8000JF SI-8000Q SI-8000S SI-8000SD SI-8000TFE SI-8000TM SI-8000W SI-8000Y SI-8100QL SI-8205NHD SI-8400L SI-8500L SI-8511NVS SLA2600M SLA6805MP SLA682xM/ 686xM/6845M TO263-5(Surface-mount) TO220F-5 TO252-5(Surface-mount) SOP8(Surface-mount) TO252-5(Surface-mount) SOP8(Surface-mount) SOP8(Surface-mount) SOT89-5(Surface-mount) TO263-5(Surface-mount) TO220F-5 HSOP44(Surface-mount) DIP30 TO220F-5 TO263-5(Surface-mount) TO220F-5 DIP8 TO263-5(Surface-mount) TO220F-5 TO263-5(Surface-mount) TO220F-5 HSOP8(Surface-mount) TO220F-5 TO263-5(Surface-mount) TO220F-5 TO252-5(Surface-mount) SOP8(Surface-mount) TO220F-7 DIP8 HSOP8(Surface-mount) Non-package type (EI-12.5 core) Non-package type (EI-19 core) TSSOP24 SLA24Pin SLA23Pin Package DIP8 DIP8 TO220F-7 HSOP8(Surface-mount) PS4(Surface-mount) SCM33Pin Standard Packing Quantities Bulk 2500 2500 1800 LF.No.2551/2552/ 2554/2556:250 2000 2000 680 2000 2000 2500 2000 2000 2000 2000 2000 2500 864 320 LF.No.2176/2179:648 LF.No.2151/2152:648 LF.No.2153:540 SLA24Pin LF.No.2171/2178:648 LF.No.2175:540 800 3000 1000 3000 1000 1000 1000 800 2000 800 800 800 1000 800 3000 1000 1000 2800 SMA682xMP/ 685xM/686xM SMA7022MU/ 7029M SMA7036M SPI-6631M SPI-8000A SPI-8000TW SSC2000S SSC2100S SSC9510 SSC9510S STA6940M STA801M STR-A6000 STR-A6100 STR-L400 STR-L6400 STR-V100 STR-W6000S STR-W6200D STR-W6700 STR-X6700 STR-Y6400 STR-Y6700 SX68000M ZIP15 (SMA15Pin) ZIP15(SMA15Pin) HSOP16(Surface-mount) HSOP16(Surface-mount) HSOP16(Surface-mount) SOP8(Surface-mount) SOP8(Surface-mount) DIP16 SOP18(Surface-mount) ZIP18(STA18Pin) ZIP10(STA10Pin) DIP8 DIP8 SIP10(STA10Pin) SIP10(STA10Pin) SIP8(STA8Pin) TO220F-6 TO220F-6 TO220F-6 TO3PF-7 TO220F-7 TO220F-7 SOP27(Surface-mount) 1440 1250 LF.No434:1785 100 2500 2500 3300 3300 4050 1800 1800 1800 500 1800 1800 1400 1400 1400 1000 1000 2000 LF1890:3000 SLA7611M SLA708xMPR SLA707xMR/MPR SLA706xM Taping 1000 2000 SLA705xM Series Name/ Product Name SLA7022MU/ 7029M SLA7024M/ 7026M/7027MU SLA703xM Package ZIP15 with Fin (SLA15Pin) ZIP18 with Fin (SLA18Pin) ZIP18 with Fin (SLA18Pin) ZIP18 with Fin (SLA18Pin) ZIP21 with Fin (SLA21Pin) ZIP23 with Fin (SLA23Pin) ZIP23 with Fin (SLA23Pin) ZIP18 with Fin (SLA18Pin) SMA24Pin LF.No.2451/2457:1080 LF.No.2452/2453:1008 1440 1080 1080 1080 1080 1080 1080 1080 Standard Packing Quantities Bulk 1080 Taping
ICs
1 ICs
ICs
<STR-V600 Series> Low height, at least 4 mm of creepage isolation between high and low terminal tips Low noise, low standby power SIP8 package version of STR-A6000 Part Number STR-V653 <STR-W6000S Series> Low noise, low standby power Brown-in and brown-out functions Part Number STR-W6051S STR-W6052S STR-W6053S <STR-W6200D Series> Low noise, low standby power External latch protection (ELP) function Part Number STR-W6251D STR-W6252D STR-W6253D Oscillation Frequency 67kHz 67kHz 67kHz MOSFET VDSS 650V 650V 650V RDS(ON) 3.95 2.8 1.9 TO220F-6 Package Oscillation Frequency 67kHz 67kHz 67kHz MOSFET VDSS 650V 650V 650V RDS(ON) 3.95 2.8 1.9 TO220F-6 Package Oscillation Frequency 67kHz MOSFET VDSS 650V RDS(ON) 1.9 Package SIP8
ICs
<STR-V100 Series> Low height, at least 4 mm of creepage isolation between high and low terminal tips Low noise, low standby power SIP8 package version of STR-A6100 Part Number STR-V152 STR-V153 Fixed off-time period 8s 11.5s MOSFET VDSS 650V 650V RDS(ON) 2.8 2 Package SIP8
<STR-Y6400 Series> High efficiency in full load range Low noise, low standby power Mode change delay time adjustable Part Number STR-Y6453 STR-Y6456 STR-Y6473 STR-Y6476 MOSFET VDSS 650V 650V 850V 850V RDS(ON) 1.8 0.73 3.6 1.3 TO220F-7 Package
<STR-L6400 Series> Low height, at least 6.5 mm of creepage isolation between high and low terminal tips High efficiency in full load range, low noise, and low standby power SIP10 package version of STR-Y6400 Part Number STR-L6472 MOSFET VDSS 850V RDS(ON) 6.5 Package SIP10
ICs
<STR-W6700 Series> High efficiency in full load range Low noise, undervoltage lockout (UVLO) standby function Part Number STR-W6723N STR-W6734 STR-W6735 STR-W6735N STR-W6753 STR-W6754 STR-W6750F STR-W6756 STR-W6756N STR-W6765 STR-W6765N MOSFET VDSS 450V 500V 500V 500V 650V 650V 650V 650V 650V 800V 800V RDS(ON) 1.4 1.0 0.57 0.57 1.7 0.96 0.73 0.73 0.73 1.8 1.8 Auto burst oscillation No Yes Yes No Yes Yes Yes Yes No Yes No Bottom-skip QR operation Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes TO220F-6 Package
<STR-X6700 Series> High efficiency in full load range Low noise, undervoltage lockout (UVLO) standby function Part Number STR-X6729 STR-X6737 STR-X6737M STR-X6756 STR-X6757 STR-X6757N STR-X6750B STR-X6750F STR-X6759N STR-X6759F STR-X6759B STR-X6768N STR-X6769 STR-X6769B MOSFET VDSS 450V 500V 500V 650V 650V 650V 650V 650V 650V 650V 650V 800V 800V 800V RDS(ON) 0.189 0.36 0.36 0.73 0.62 0.62 0.62 0.62 0.385 0.385 0.385 1.0 0.66 0.66 Auto burst oscillation No Yes No Yes Yes No No Yes No Yes No No Yes No Bottom-skip QR operation Yes Yes Yes Yes Yes Yes No No Yes No No Yes Yes No TO3PF-7 Package
ICs
ICs
Selection Guide
<Single Output>
Surface-Mount Type
Output Current Series Name (A) SAI SI-8000W SI-8000JD SI-8000TM NR885K SI-8205NHD SI-8000SD SPI-8000A SI-8000Q SI-8000FDE SI-8000FDL SI-8000HD 0.4 0.5 0.6 1.5 1.5 3.0 3.0 3.0 3.0 3.5 3.5 3.5 5.5 35 43 43 20 46 43 53 30 43 43 43 60 125 300 350 200 to 1000 60 250 500 300 300 150 SOP8 TO263-5 TO252-5 HSOP8 HSOP8 TO263-5 HSOP16 HSOP8 TO263-5 TO263-5 TO263-5 Active: low Current mode control Current mode control, soft start Current mode control, synchronous rectifier 3.3 Output Voltage (V) 5.0 9.0 12 Variable (Reference Voltage) (V) 0.5 0.8 1.0 Maximum Input Voltage (V) 35 Oscillation Frequency (kHz) 60 PS-4 12 14 16 18 52 50 20 22 26 28 28 30 Package Remarks Page
Thru-Hole Type
Output Current Series Name (A) SI-8400L SI-8000E SI-8500L SI-8000JF SI-8000TFE SI-8000GL SI-8000S SI-8100QL SI-8000FFE SI-8000HFE SI-8000Y 0.5 0.6 1.0 1.5 1.5 1.5 3.0 3.5 3.5 5.5 8.0 3.3 Output Voltage (V) 5.0 9.0 12 15 Variable (Reference Voltage) (V) 0.5 0.8 1.0 1.5 Maximum Input Voltage (V) 35 43 35 43 43 53 43*1 30 43 43 45 Oscillation Frequency (kHz) 60 60 60 125 300 250 60 350 300 150 130 Non-package type With coil and built-in diode TO220F-5 Non-package type With coil and built-in diode TO220F-5 TO220F-5 DIP8 TO220F-5 DIP8 TO220F-5 TO220F-5 TO220F-7 Current mode control Current mode control 54 32 54 34 36 38 40 42 44 46 48 Package Remarks Page
<Multi Output>
Output Current Part Number (A) STA801M ch1 ch2 SPI-8001TW ch1 ch2 SPI-8002TW ch1 ch2 SPI-8003TW ch1 ch2 0.5 0.5 1.5 1.5 1.5 1.5 1.5 1.5 (V) 5 Select from 9.0, 11.5, 12.1, and 15.5. Variable (1.0 to 16 V) Variable (1.0 to 16 V) Variable (1.0 to 24 V) Variable (1.0 to 24 V) Variable (1.0 to 24 V) Variable (1.0 to 24 V) 40 200 to 400 HSOP16 Frequency variable 58 40 250 HSOP16 58 21 250 HSOP16 58 (V) 43 (kHz) 125 ZIP10 Built-in flywheel diode 56 Output Voltage Maximum Input Voltage Oscillation Frequency Package Remarks Page
<Control ICs>
Variable (Reference Voltage) Series Name (V) SI-8511NVS 1.1 (V) 25 (kHz) 100 to 400 TSSOP24 Synchronous rectifier, PRC (fixed to ton) 62 Maximum Input Voltage Oscillation Frequency Package Remarks Page
10
ICs
Application Note
Heat Dissipation and Reliability
The reliability of an IC is highly dependent on its operating temperature. Please be sure to apply silicone grease to the IC and to mount it to the heatsink with a proper mounting torque. Heatsink design should pay particular attention to ensuring sufficient heat dissipation capacity. In addition, please take into account the air convection in operation. The reliability of discrete components such as capacitors and coils is closely related to temperature. A high operating temperature may reduce the service life. Exceeding the allowable temperature may burn the coils or damage capacitors. It is important to make sure that the temperature of output smoothing coils and input/output capacitors do not exceed their allowable levels during operation. With an adequate derating for the coils, minimize heat emission as far as possible. (For discrete components, refer to the individual user manuals.)
Mounting Torque
SI-8000E SI-8000JF SI-8000S SI-8000TFE SI-8000HFE SI-8000FFE SI-8000Y
Others
Devices can not be operated in parallel connection aiming for a larger current. Not applicable for the current boost or voltage step-up use.
Thermal Design
The maximum junction temperature Tj(max) given in the Absolute Maximum Ratings is specific to each product type and must be strictly observed. Thus, thermal design must consider the maximum power dissipation PD(max), which varies by the conditions of use, and the maximum ambient temperature Ta(max). To simplify thermal design, Ta-PD characteristic graphs are provided herein. Please observe the following steps for heatsink design: 1. Obtain the maximum ambient temperature Ta(max). 2. Obtain the maximum power dissipation PD(max). 3. Look for the intersection point on the Ta-PD characteristic graph and determine the size of the heatsink. Although the heatsink size is now obtained, in actual applications, 10-to20% derating factor is generally introduced. Moreover, the heat dissipation capacity of a heatsink highly depends on how it is mounted. Thus, it is recommended to measure the heatsink and case temperature in the actual operating environment. Please refer to the Ta-PD characteristic graphs for respective product types.
FMM-22S,R (Center-tap Type,VRM=200V,IO=10 A) AM01Z (Axial Type,VRM=200V,Io=1.0A) RM10Z (Axial Type,VRM=200V,Io=1.5A) RM4Z (Axial Type,VRM=200V,Io=3.0A) FMM-22S,R (Center-tap Type,VRM=200 V,IO=10 A) RM10Z (Axial Type,VRM=200V,Io=1.5A) AM01Z (Axial Type,VRM=200V,Io=1.0A) AM01Z (Axial Type,VRM=200V,Io=1.0A)
ICs
11
Line up
Part Number VO(V) IO(A) SAI01 5.0 0.5 SAI02 3.3 SAI03 12.0 0.4
j-c
Applications
Power supplies for telecommunication equipment Onboard local power supplies
Electrical Characteristics
Ratings Parameter Symbol min. Output Voltage Efficiency Oscillation Frequency Line Regulation Load Regulation Temperature Coefficient of Output Voltage Ripple Rejection Overcurrent Protection Starting Current VO Conditions 4.80 SAI01 typ. 5.00 VIN=20V, IO=0.3A 80 VIN=20V, IO=0.3A 60 VIN=20V, IO=0.3A 80 VIN=10 to 30V, IO=0.3A 30 VIN=20V, IO=0.1 to 0.4A 0.5 45 f=100 to 120HZ 0.55 VIN=10V 0.55 VIN=8V 40 100 max. 5.20 min. 3.17 SAI02 typ. 3.30 VIN=15V, IO=0.3A 75 VIN=15V, IO=0.3A 60 VIN=15V, IO=0.3A 60 VIN=8 to 28V, IO=0.3A 20 VIN=15V, IO=0.1 to 0.4A 0.5 45 f=100 to 120HZ 0.45 VIN=18V 30 80 max. 3.43 min. 11.40 SAI03 typ. 12.00 VIN=24V, IO=0.3A 88 VIN=24V, IO=0.3A 60 VIN=24V, IO=0.3A 100 VIN=18 to 30V, IO=0.3A 70 VIN=24V, IO=0.1 to 0.4A 1.5 45 f=100 to 120HZ 95 130 max. 12.60
(Ta=25C) Unit
V % kHZ mV mV mV/ C dB A
Conditions f Conditions VOLINE Conditions VOLOAD Conditions VO/Ta RREJ Conditions IS1 Conditions
12
ICs
SAI Series
(unit : mm)
0.25
2.54
4.32
4 .GND
+0.15 0.75 0.05
max.
0.2
3VOS
2 SW
1VIN
0.15
4.7
6.8
max.
3.6
0.2
8.0 6.3
0.5 0.2
4.0
max.
Pin Assignment q VIN w SWOUT e VOS r GND Plastic Mold Package Type Flammability: UL94V-0 Product Mass: Approx. 0.22g
0.89
0 to 0.15 1.0
0.3
3.0 9.8
0.2
0.3
0.3 0.05
0.25
+0.15
Block Diagram
VIN 1 OCP Reg. 2 SWOUT
VIN
VIN
SWOUT
L1 2 3
OSC
TSD
+
SAI
C1 100F GND 4
VOS
D1 SJPB-D4 (Sanken)
3 VOS
C2 330F
GND
GND
Ta-PD Characteristics
0.8 0.7
PD=VOIO
Glass epoxy board (95691.2) Natural air cooling
100 1
VFIO 1
VO VIN
The efficiency depends on the input voltage and the output current. Therefore, obtain the value from the efficiency graph and substitute the percentage in the formula above. VO : Output voltage IO : Output current : Efficiency (%) VF : Diode D1 forward voltage SJPB-D4-0.3V
50
75
100
125
ICs
13
SI-8000W Series
Features
Surface-mount package (SOP8) Output current: 0.6A High efficiency: 75 to 80% Requires only 4 discrete components
Internally-adjusted phase correction and output voltage adjustment performed internally Built-in reference oscillator (60kHz) Built-in overcurrent and thermal protection circuits
j-L j-a
Applications
Power supplies for telecommunication equipment Onboard local power supplies
Electrical Characteristics
Ratings Parameter Symbol min. Output Voltage Efficiency Oscillation Frequency Line Regulation Load Regulation Temperature Coefficient of Output Voltage Ripple Rejection Overcurrent Protection Starting Current VO Conditions 3.17 SI-8033W typ. 3.30 VIN=15V, IO=0.3A 75 VIN=15V, IO=0.3A 60 VIN=15V, IO=0.3A 60 VIN=8 to 28V, IO=0.3A 20 VIN=15V, IO=0.1 to 0.4A 0.5 45 f=100 to 120HZ 0.61 VIN=15V 0.61 VIN=20V 30 80 max. 3.43 min. 4.80 SI-8050W typ. 5.00 VIN=20V, IO=0.3A 80 VIN=20V, IO=0.3A 60 VIN=20V, IO=0.3A 80 VIN=10 to 30V, IO=0.3A 30 VIN=20V, IO=0.1 to 0.4A 0.5 45 f=100 to 120HZ 40 100 max. 5.20
(Ta=25C) Unit
V % kHZ mV mV mV/ C dB A
Conditions f Conditions VOLINE Conditions VOLOAD Conditions VO/Ta RREJ Conditions IS1 Conditions
14
ICs
SI-8000W Series
(Unit : mm)
1.550.15
0t
0.995max.
o1
1.27
Pin Assignment q VIN w N.C e SW r VOS t GND y GND u GND i GND Plastic Mold Package Type Flammability: UL94V-0 Product Mass: Approx. 0.1g
4.40.2
Block Diagram
VIN 1 OCP Reg. OSC 3 SW
TSD
C1 100F +
SI-8000W
GND 5 to 8
VOS
C2 330F
Amp. VREF
5 to 8
4 VOS
GND
GND
GND
Reference Data
Copper Laminate Area vs. Power Dissipation
1.2 Tj=100C Area of PC board : 40 40mm Ta=25C 1
Power Dissipation PD (W)
Ta=50C Ta=80C
120
Thermal Resistance j-a (C/W)
0.8
100
0.6 0.4
80
60
0.2
0 10
1000
40 10
1000
ICs
15
SI-8000JD Series
Features
Surface-mount package (TO263-5) Output current: 1.5A High efficiency: 77 to 88% Requires only 4 discrete components Internally-adjusted phase correction and output voltage
Capable of downsizing a choke-coil due to IC's high switching frequency (125 kHz). (Compared with conventional Sanken devices) Built-in foldback-overcurrent and thermal protection circuits Output ON/OFF available (Circuit current at output OFF: 200A max) Soft start available by ON/OFF pin Conditions
Junction Temperature Storage Temperature Thermal Resistance (Junction to Case) Thermal Resistance (Junction to Ambient Air)
j-c j-a
Applications
Power supplies for telecommunication equipment Onboard local power supplies, etc.
Electrical Characteristics
Ratings Parameter Symbol min. VO Output Voltage Efficiency Oscillation Frequency Line Regulation Load Regulation Temperature Coefficient of Output Voltage Overcurrent Protection Starting Current Low Level Voltage ON/OFF* Pin Outflow Current at Low Voltage Conditions 3.234 SI-8033JD typ. 3.30 77 VIN=15V, IO=0.5A 125 VIN=15V, IO=0.5A 25 10 0.5 1.6 VIN=15V 0.5 100 7 VIN=15V, Io=0A 200 VIN=15V, VON/OFF=0.3V 7 VIN=20V, Io=0A 200 VIN=20V, VON/OFF=0.3V 1.6 VIN=20V 0.5 100 VSSL=0V 7 VIN=21V, Io=0A 200 VIN=21V, VON/OFF=0.3V 7 VIN=24V, Io=0A 200 VIN=24V, VON/OFF=0.3V 80 30 VIN=8 to 30V, IO=0.5A VIN=15V, IO=0.2 to 0.8A max. 3.366 min. 4.90 SI-8050JD typ. 5.00 82 VIN=20V, IO=0.5A 125 VIN=20V, IO=0.5A 40 10 0.5 1.6 VIN=21V 0.5 100 100 40 VIN=10 to 30V, IO=0.5A VIN=20V, IO=0.2 to 0.8A max. 5.10 min. 8.82 SI-8090JD typ. 9.00 86 VIN=21V, IO=0.5A 125 VIN=21V, IO=0.5A 50 10 1.0 1.6 VIN=24V 0.5 100 120 40 VIN=15 to 30V, IO=0.5A VIN=21V, IO=0.2 to 0.8A max. 9.18 min. 11.76 SI-8120JD typ. 12.00 88 VIN=24V, IO=0.5A 125 VIN=24V, IO=0.5A 60 10 1.0 130 VIN=18 to 30V, IO=0.5A 40 VIN=24V, IO=0.2 to 0.8A max. 12.24
(Ta=25C) Unit
VIN=15V, IO=0.5A
VIN=20V, IO=0.5A
VIN=21V, IO=0.5A
VIN=24V, IO=0.5A
V % kHZ mV mV mV/ C A V
Conditions f Conditions VOLINE Conditions VOLOAD Conditions VO/Ta IS1 Conditions VSSL ISSL Conditions Iq Conditions Iq(oFF) Conditions
A
mA
*: Pin 5 is the ON/OFF pin. Soft start at power on can be performed with a capacitor connected to this pin. The output can also be turned ON/OFF with this pin. The output is stopped by setting the voltage of this pin to VSSL or lower. ON/OFF-pin voltage can be changed with an open-collector drive circuit of a transistor. When using both the soft-start and ON/OFF functions together, the discharge current from C3 flows into the ON/OFF control transistor. Therefore, limit the current securely to protect the transistor if C3 capacitance is large. The ON/OFF pin is pulled up to the power supply in the IC, so applying the external voltage is prohibited.
SI-8000JD
SI-8000JD
SI-8000JD
5 ON/OFF
5 ON/OFF C3
5 ON/OFF C3
VOUT. ON/OFF
Soft Start
16
ICs
SI-8000JD Series
(Unit : mm)
10.0
0.2
1.2
(15)
(4.6)
(1.75)
(6.8)
0.2
0.2
1.5 Dp:
0.2
(3)
(2R0.45)
(3)
0.1
0.10 (3)
0.15
2.4 (R0.3)
0.3
0.2
0.88
0.10
(R0.3)
0 to 6 (0.5)
0.1
Pin Assignment q VIN w SWOUT e GND r VOS t ON/OFF Plastic Mold Package Type Flammability: 94V-0 Product Mass: Approx. 1.48g
9.2
0.3
15.3
0.2
2.0
15.30
0.3
(0.75)
4.9
(1.7
0.25
) 1 2 3 4 9.9
0.2
0.1
2.54
(1.7
0.25
(3) 2-R0.3
10.0
0.02
Block Diagram
SWOUT
4.9
0.2
9.2
SI-8000JD
C1 + ON/OFF GND 5 3 C3
VOS
C2
GND
Comp. Error Amp.
+
GND
TSD
VREF GND 3
C1 C2 C3 L1 Di
: : : : :
50V/220F 25V/470F 10V/0.47F (Only when using soft-start function) 100H SJPB-H6 (Sanken)
Reference Data
Copper Laminate Area on Glass Epoxy Board vs. Thermal Resistance (Junction to Ambient Air) (Typical Value)
Thermal Resistance (junction to ambient air) j-a (C/W )
55 50 2.6 2.4 2.2 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0
45 40 35 30 0
200
400
600
800
1000
1200
1400
1600
1800
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
Ta-PD Characteristics
3.5 3
Copper Area 4040 mm ( j-a : 33.3C/W) 2040 mm ( j-a : 37C/W) 2020 mm ( j-a :44C/W) 1010 mm ( j-a : 53C/W)
PD=VOIO
The efficiency depends on the input voltage and the output current. Therefore, obtain the value from the efficiency graph and substitute the percentage in the formula above. VO : Output Voltage VIN : Input Voltage IO : Output Current
: Efficiency (%)
VF : D1 forward voltage 0.4V(IO=2A)(SJPB-H6) Thermal design for D1 must be considered separately.
0 25
25
50
75
100
125
ICs
17
SI-8000TM Series
Features
Compact surface-mount package (TO252-5) Output current: 1.5 A High efficiency: 81% typ. (at Vo = 5 V) Requires only 4 discrete components Built-in reference oscillator (300 kHz) Built-in drooping-type-overcurrent and thermal protection circuits Output ON/OFF available (circuit current at output OFF: 200 A typ.) Soft start available by ON/OFF pin
j-c j-a
*: This product has built-in thermal protection circuits that may operate when the junction temperature rises above 130C. The recommended design for the junction temperature during operation is below 125C.
Applications
Onboard local power supplies AV equipment OA equipment
*1: The minimum value of an input voltage range is the higher of 4.5 V or VO + 3 V.
Electrical Characteristics
Rating Parameter Symbol
(Ta=25C)
Reference Voltage Temperature Coefficient of Reference Voltage Efficiency Oscillation Frequency Line Regulation Load Regulation Overcurrent Protection Starting Current
VADJ
Conditions VADJ/T Conditions
min. 0.784
Conditions
SI-8008TM typ. 0.800 VIN=15V, Io=0.1A 0.1 VIN=15V, Io=0.1A, Tc=0 to 100C 81 VIN=15V, Io=0.5A
Unit
max. 0.816
V mV/C % kHz
fo
Conditions VOLINE Conditions VOLOAD Conditions
80
mV mV A
40
IS
Conditions
Low Level Voltage VSSL ON/OFF Pin* Outflow Current at Low Voltage
V
A
ISSL
Conditions
Iq
Quiescent Circuit Current Conditions
mA
A
Iq (OFF)
Conditions
*: Pin 5 is the SS pin. Soft start at power on can be performed with a capacitor connected to this pin. The output can also be turned ON/OFF with this pin. The output is stopped by setting the voltage of this pin to VSSL or lower. SS-pin voltage can be changed with an open-collector drive circuit of a transistor. When using both the soft-start and ON/OFF functions together, the discharge current from C3 flows into the ON/OFF control transistor. Therefore, limit the current securely to protect the transistor if C3 capacitance is large. The SS pin is pulled up to the power supply in the IC, so applying the external voltage is prohibited. If the pin is not used, leave it open.
SI-8000TM
SI-8000TM
SI-8000TM
5 SS
5 SS C3
5 SS C3
VO. ON/OFF
Soft start
18
ICs
SI-8000TM Series
(Unit : mm)
2.30
0.20
5.34 0.500.10
0.20
(5.04) (1.50)
1.10
0.20
9.90
1.180.20
2.700.20
2.700.20
(0.89)
9.90
Pin Assignment q IN w SW e GND r ADJ t SS Plastic Mold Package Type Flammability: UL94V-0 Product Mass: Approx. 0.33 g
R0
.3 2
6.100.20
0.30
(4.06)
0.1
8 0 to 0.500.10
(1.00)
Block Diagram
VIN
SW 2
0.30
IN
SW
2 R1
VO
SI-8000TM
C1 220F + SS 5 C3 GND 3
ADJ 4 R2 Di IADJ
C2 470F
Comp.
+ +
Thermal Protection
ADJ 4
GND
GND
Error Amp.
C1 C2 C3 L1 Di
: 220F : 470F : 1F (Only when using soft-start function) : 47F : SJPB-H6 (Sanken)
ICs
19
SI-8000SD Series
Features
Surface-mount package (TO263-5) Output current: 3.0A
High efficiency: 79% typ. (SI-8033SD), 84% typ. (SI-8050SD) Requires only 4 discrete external components Internally-adjusted phase correction and output voltage Built-in reference oscillator (60kHz) Built-in overcurrent and thermal protection circuits Output ON/OFF available Soft start available by S.S pin
j-c j-a
Applications
Power supplies for telecommunication equipment Onboard local power supplies
Electrical Characteristics
Ratings Parameter Symbol min. Output Voltage Efficiency Oscillation Frequency Line Regulation Load Regulation Temperature Coefficient of Output Voltage Overcurrent Protection Starting Current Soft Start Pin* Low-Level Voltage Outflow Current at Low Voltage VO Conditions 3.17 SI-8033SD typ. 3.3 VIN=15V, IO=1A 79 VIN=15V, IO=1A 60 VIN=15V, IO=1A 25 VIN=8 to 28V, IO=1A 10 VIN=15V, IO=0.5 to 1.5A 0.5 3.1 VIN=15V 0.2 20 30 40 VSSL=0.2V 20 3.1 VIN=20V 0.2 30 40 30 80 max. 3.43 min. 4.8 SI-8050SD typ. 5.0 VIN=20V, IO=1A 84 VIN=20V, IO=1A 60 VIN=20V, IO=1A 40 VIN=10 to 30V, IO=1A 10 VIN=20V, IO=0.5 to 1.5A 0.5 40 100 max. 5.2
(Ta=25C) Unit
V % kHZ mV mV mV/ C A V
Conditions f Conditions VOLINE Conditions VOLOAD Conditions VO/Ta IS1 Conditions VSSL ISSL Conditions
* Pin 5 is a soft start pin. Soft start at power on can be performed with a capacitor connected to this pin. The output can also be turned ON/OFF with this pin. The output is stopped by setting the voltage of this pin to VSSL or lower. Soft-start pin voltage can be changed with an open-collector drive circuit of a transistor. When using both the soft-start and ON/OFF functions together, the discharge current from C3 flows into the ON/OFF control transistor. Therefore, limit the current securely to protect the transistor if C3 capacitance is large. The ON/OFF pin is pulled up to the power supply in the IC, so applying the external voltage is prohibited. If this pin is not used, leave it open.
SI-8000SD
SI-8000SD
SI-8000SD
5 ON/OFF
5 ON/OFF C3
5 ON/OFF C3
VOUT. ON/OFF
Soft start
20
ICs
SI-8000SD Series
(Unit : mm)
10.0
0.2
1.2
(15)
4.5
0.2
(6.8)
0.2
9.2
0.3
15.3
(3)
0.1
0.10 (3)
0.15
15.30
0.3
9.2
0.2
1.5 Dp:
0.2
(3)
(2R0.45)
Pin Assignment q VIN w SWOUT e GND r VOS t S.S Plastic Mold Package Type Flammability: 94V-0 Product Mass: Approx. 1.48g
(4.6)
2.4 (R0.3)
0.3
0.2
0.2
2.0
(0.75)
4.9
0.88
0.10
(R0.3)
2.54
0 to 6 (0.5)
0.1
(1.7
0.25
) 1 2 3 9.9 4
0.2
0.1
(1.7
0.25
Block Diagram
Reference Data
Copper Laminate Area on Glass Epoxy Board vs. thermal resistance (junction to ambient air) (Typical Value)
VIN
Internal power supply
SWOUT
Overcurrent protection
2
Thermal resistance (junction to ambient air) j-a (C/W)
Oscillator
Reset
Comparator
Thermal protection
VOS
Error amplifier
4.9
0.2
Reference voltage
200
400
600
800
1000
1200
1400
1600
1800
S.S 5 3
GND
SI-8000SD
C1 + S.S 5 C3 GND GND 3
VOS
C2
C1 : 50V/1000F C2 : 50V/1000F C3 : 0.01F (only when soft start function is used) L1 : 150H D1 : SPB-G56 (Sanken)
GND
Diode D1 Be sure to use Schottky-barrier diode as D1. If other diodes like fast recovery diodes are used, ICs may be destroyed because of the reverse voltage generated by the recovery voltage or ON voltage. Choke coil L1 If the winding resistance of the choke coil is too high, the efficiency may drop below the rated value. As the overcurrent protection starting current is about 3.5 A, take care concerning heat radiation from the choke coil caused by magnetic saturation due to overload or short-circuited load. Capacitors C1, C2, and C3 As large ripple currents flow through C1 and C2, use high-frequency and low-impedance capacitors aiming for switching-mode-power-supply use. Especially when the impedance of C2 is high, the switching waveform may become abnormal at low temperatures. For C2, do not use a capacitor with an extremely low equivalent series resistance (ESR) such as an OS capacitor or a tantalum capacitor, which may cause an abnormal oscillation. C3 is a capacitor for soft start. Leave pin 5 open if the soft start function is not used. This pin is pulled up with a pull-up resistor inside the ICs. To create the optimum operating conditions, place the components as close as possible to each other.
ICs
21
SPI-8000A Series
Features
Surface-mount 16 pin package Output current: 3.0A
High efficiency: 91% (at VIN = 10V, lO = 1A, VO = 5V) Capable of downsizing a choke-coil due to IC's high switching frequency (125kHz). (Compared with conventional Sanken devices) The output-voltage-variable type can vary its output voltage from 1V to 14V because of its low reference voltage (Vref) of 1V. Wide Input Voltage Range (8 to 50V) Output ON/OFF available Built-in overcurrent and thermal protection circuits
j-c*2 j-a*2
*1: Limited due to thermal protection. *2: When mounted on glass-epoxy board 700cm2 (copper laminate area 30.8cm2).
Applications
Onboard local power supplies OA equipment For stabilization of the secondary-side output voltage of switching power supplies
*1: The minimum value of an input voltage range is the higher of either 8V or VO+3V. *2: Please be sure to let the output current run more than 20 mA. When using by less than 20 mA, there is a possibility that the output voltage becomes unstable.
Electrical Characteristics
Rating Parameter Symbol min. Reference Voltage Efficiency Oscillation Frequency Line Regulation Load Regulation Temperature Coefficient of Reference Voltage Overcurrent Protection Starting Current Quiescent Circuit Current Circuit Current at Output OFF CE/SS Terminal Low Level Voltage Outflow Current at Low Voltage VREF Conditions Eff Conditions FOSC Conditions VOLINE Conditions VOLOAD Conditions VREF/Ta IS Conditions Iq Conditions Iq(off) Conditions VSSL ISSL Conditions VSSL=0V VIN=12V, VON/OFF=0.3V 0.5 50 3.1 VIN=12V 7 VIN=12V, IO=0A 400 0.97 SPI-8010A (Variable type) typ. 1.00 VIN=12V, IO=1A 86 VIN=20V, IO=1A, VO=5V 250 VIN=12V, IO=1A 20 VIN=10 to 30V, IO=1A 10 VIN=12V, IO=0.1 to 1.5A 0.5 30 40 max. 1.03
(Ta=25C) Unit
V % kHZ mV mV mV/C A mA
A
V
* Pin 4 is the CE/SS pin. Soft start at power on can be performed with a capacitor connected to this pin. The output can also be turned ON/OFF with this pin. The output is stopped by setting the voltage of this pin to VSSL or lower. CE/SS-pin voltage can be changed with an opencollector drive circuit of a transistor. When using both the soft-start and ON/OFF functions together, the discharge current from C4 flows into the ON/OFF control transistor. Therefore, limit the current securely to protect the transistor if C3 capacitance is large. The CE/SS pin is pulled up to the power supply in the IC, so applying the external voltage is prohibited.
SPI-8000A
SPI-8000A
SPI-8000A
4 CE/SS
4 CE/SS C4
4 CE/SS C4
VO. ON/OFF
Soft start
22
ICs
SPI-8000A Series
(Unit : mm)
2.0+0.2/-0.08
2.75MAX
2.50.2
0.25+0.15/-0.05
10.50.3
S 12.20.2
(Gate remains: Not included in dimensions)
0.10
(11)
Pin Assignment 1.AGND 2.N.C 3.DGND 4.CE/SS 5.Reg 6.N.C 7.SWOUT 8.N.C 9.N.C 10.N.C 11.VIN 12.B.S 13.N.C 14.Comp 15.VREF 16.N.C Product Mass : Approx 0.86g
(2)
16
(4.5)
1.270.25
0.4+0.15/-0.05
Block Diagram
SPI-8010A
VIN
P.REG
OCP BS
7.50.2
PWM LOGIC
SWOUT
VREF Comp
Amp +
1V
GND
ICs
23
B.S
11
R1 L1 C3
VIN
4 C1
VIN CE/SS
C7
SPI-8010A
SWOUT
7 D1 R2
V0
DGND VREF
3
+
C2 C8 IREF
15 R3
GND
GND
C1: 220F/63V C2: 470F/25V C3: 0.1F C4: 1000pF C5: 0.1F C6: 0.047F C7: 0.1F C8: 0.1F R1: 47 L1: 47H D1: SPB-G56S (Sanken)
Diode D1 Be sure to use a Schottky-barrier diode for D1. If other diodes like fast recovery diodes are used, ICs may be destroyed because of the reverse voltage generated by the recovery voltage or ON voltage. Choke coil L1 If the winding resistance of the choke coil is too high, the efficiency may drop below the rated value. As the overcurrent protection starting current is about 4.5A, take care concerning heat radiation from the choke coil caused by magnetic saturation due to overload or short-circuited load. Capacitors C1, C2 As large ripple currents flow through C1 and C2, use high-frequency and low-impedance capacitors aiming for switching-mode-power-supply use. Especially when the impedance of C2 is high, the switching waveform may become abnormal at low temperatures. For C2, do not use a capacitor with an extremely low equivalent series resistance (ESR) such as an OS capacitor or a tantalum capacitor, which may cause an abnormal oscillation. Resistors R2, R3 R2 and R3 are the resistors to set the output voltage. Set their values so that IREF becomes approx. 2mA. Obtain R2 and R3 values by the following formula: R2= VREF (VOUTVREF) (VOUT1) 1 . = (), R3 = = = .500() IREF 2103 IREF 2103
To create the optimum operating conditions, place the components as close as possible to each other.
Ta-PD Characteristics
3.00
PD=VO IO
Power Dissipation PD (W)
2.50
j-a:41.7C/W(30.8cm2) j-a:47.6C/W(8.64cm2)
100 VO 1 VF IO 1 VIN
2.00
j-a:62.5C/W(0.84cm2)
1.50
Note 1: The efficiency depends on the input voltage and the output current. Therefore, obtain the value from the efficiency graph and substitute the percentage in the formula above. Note 2: Thermal design for D1 must be considered separately. VO : Output voltage VIN : Input voltage IO : Output current : Efficiency (%) VF : Diode D1 forward voltage SPB-G56S0.4V(IO=2A)
1.00
0.50
0 30
25
50
75
100
125
24
ICs
ICs
25
SI-8000Q Series Surface Mount, Current Mode Cntrol Step-down Switching Mode
Features
Compact surface-mount package (HSOP8) Introduction of current mode control method Output current: 3.5 A High efficiency: 90% (Vo = 5 V) Built-in reference oscillator (500 kHz) A ceramic capacitor can be used for output Built-in drooping-type overcurrent and thermal protection circuits Built-in soft start circuit Built-in on/off function (Active Hi) Low current consumption during off
j-c j-a
*1: Limited by thermal protection circuit *2: Note that the detection temperature for thermal protection is about 140C.
Applications
DVD recorder, FPD-TV Onboard local power supplies OA equipment
*1: The minimum value of the input voltage range is 4.75 V or Vo +3 V, whichever is higher.
Electrical Characteristics
Rating Parameter Symbol min. Reference Voltage Temperature Coefficient of Reference Voltage Efficiency Oscillation Frequency Line Regulation Load Regulation Overcurrent Protection Starting Current VADJ Conditions VADJ/T Conditions 0.485 SI-8005Q typ. 0.500 VIN=12V, Io=1A 0.05
(R1=4.2k, R2=0.8k when Ta = 25C and Vo=5V) Unit max. 0.515 V mV/ C % 550 60 60 6.0 VIN=12V 18 Conditions Iq(OFF) Conditions VIN=12V, Io=0A, VEN=0V 5 Conditions Vc/EN Conditions Vc/EL Conditions IC/EH Conditions AEA GEA 1/GCS DMAX DMIN VIN=12V 5 VEN=0V 1000 800 0.35 92 100 2.8 VIN=12V 2.2 VIN=16V, VSSL=0V ISSL VIN=12V, Io=0A, VEN=open 20 kHz mV mV A mA
VIN=12V, Io=1A, Ta=40 to +85C 90 VIN=12V, Io=1A 450 500 VIN=16V, Io=1A 30 VIN=8 to 28V, Io=1A 30 VIN=12V, Io=0.1 to 3.5A 3.6
A A
V V
SS Pin
EN Pin
A
V/V
Error Amplifier Voltage Gain Error Amplifier Transformer Conductance Current Sense Amplifier Impedance Maximum ON Duty Minimum ON Time
A/V
V/A % nsec.
*: Pin 8 is the SS pin. Soft start at power on can be performed with a capacitor connected to this pin. The SS pin is pulled up to the power supply in the IC, so applying the external voltage is prohibited.
SI-8008Q
8 SS C8
26
ICs
Soft start
SI-8000Q Series
(Unit : mm)
4.40
6.20
Pin 1 Mark
Enlarged View of A
Pin Assignment 1BS 2IN 3SW 4GND 5FB 6COMP 7EN 8SS Plastic Mold Package Type Flammability: UL 94V-0
0.050.05
1.27 0.40
0.4
2.70
0.15
0.080.08
2.90
Block Diagram
2 IN
OSC 5v_ldo
P.REG VREF
0.5V 7 EN ON OFF
Drive 3 SW 5v_ldo
6 COMP UVLO
Amp 0.5V
5 FB
4 GND
8 SS
2 IN EN SI-8000Q
1 BS
VO
C1 C5
SS
COMP 6 C3
GND
C6 OPEN
R3
GND
ICs
27
Lineup
Part Number VO(V) IO(A) Function Soft start SI-8001FDE Variable(0.8 to 24) 3.5 ON/OFF SI-8001FDL
Applications
DVD recorder, FPD-TV OA equipment, such as printers Onboard local power supplies
*1 : Limited by thermal protection circuit *2 : This product has built-in thermal protection circuits that may activate when the junction temperature exceeds 130C. The recommended design for the junction temperature during IC operation is below 125C.
VIN Output Voltage Range VO Output Current Range IO Operating Junction Temperature Range Tjop Operating Temperature Range Top *1: The minimum value of the input voltage range is 4.5 V or Vo + 3 V, whichever is higher.
Electrical Characteristics
Ratings Parameter Symbol min. Reference Voltage Temperature Coefficient of Reference Voltage Efficiency Oscillation Frequency Line Regulation Load Regulation Overcurrent Protection Starting Current Low Level Voltage SS Pin*1 Outflow Cuurent at Low Voltage ON/OFF Control Voltage (Output on) ON/OFF Pin*2 ON/OFF Control Voltage (Output off) ON/OFF Controll Current (Output on) VADJ Conditions VADJ/T Conditions 0.784 SI8001FDE typ. 0.800 VIN=15V, Io=0.2A 0.1 VIN=15V, Io=0.2A, Tc=0 to 100C 83 VIN=15V, Io=2A 270 300 VIN=15V, Io=2A 80 VIN=10 to 30V, Io=2A 50 VIN=15V, Io=0.2 to 3.5A 3.6 VIN=15V 0.5 6 VIN=15V, VSS=0V 6 VIN=15V, Io=0A 200 VIN=15V, Vss=0V 600 2.0 30 3.6 330 270 max. 0.816 min. 0.784
(R1=4.2k, R2=0.8k when Ta = 25C and Vo=5V) SI8001FDL typ. 0.800 VIN=15V, Io=0.2A 0.1 VIN=15V, Io=0.2A, Tc=0 to 100C 83 VIN=15V, Io=2A 300 VIN=15V, Io=2A 80 VIN=10 to 30V, Io=2A 50 VIN=15V, Io=0.2 to 3.5A VIN=15V 0.8 6 Vc=2V 6 VIN=15V, Io=0A 30 VIN=15V, Vc=2V 200 100 330 max. 0.816 V mV/ C % kHz mV mV A V Unit
Conditions fO Conditions VOLINE Conditions VOLOAD Conditions IS Conditions VSSL ISSL Conditions Vc, IH Vc, IL Ic, IH Conditions Iq Conditions Iq(OFF) Conditions
A
V V
A
mA
*1: Pin 5 is the SS pin. Soft start at power on can be performed with a capacitor connected to this pin. The output can also be turned ON/OFF with this pin. The output is stopped by setting the voltage of this pin to VSSL or lower. SS-pin voltage can be changed with an open-collector drive circuit of a transistor. When using both the soft-start and ON/OFF functions together, the discharge current from C3 flows into the ON/OFF control transistor. Therefore, limit the current securely to protect the transistor if C3 capacitance is large. The SS pin is pulled up (3.7 V typ.) to the power supply in the IC, so applying the external voltage is prohibited. If this pin is not used, leave it open. *2: Output is OFF when the output control terminal VC is open. Each input level is equivalent to LS-TTL. Therefore, the device can be driven directly by LS-TTLs.
SI-8001FDE
SI-8001FDE
SI-8001FDE
5 SS
5 SS C3
5 SS C3
VO.ON/OFF
Soft start
28
ICs
SI-8000FD Series
(Unit : mm)
10.0
0.2
1.2
(15)
(4.6)
(1.75)
(6.8)
0.2
9.2
0.3
15.3
(3)
0.1
0.10 (3)
0.15
2.4 (R0.3)
0.3
0.2
0.2
2.0
15.30
0.3
(0.75)
4.9
0.88
0.10
(R0.3)
2.54
0 to 6 (0.5)
0.1
(1.7
0.25
) 1 2 3 4 9.9
0.2
0.1
4.9
0.2
9.2
0.2
1.5 Dp:
0.2
(3)
(2R0.45)
Pin Assignment 1 IN 2 SW 3 GND (Common to the rear side of the product) 4 VADJ 5 SS or Vc Plastic Mold Package Type Flammability: UL 94V-0 Product Mass: Approx. 1.48g
(1.7
0.25
(3) 2-R0.3
10.0
0.02
Block Diagram
SI-8001FDE SI-8001FDL
IN PReg. OCP
SW
SW
5 SS
ON/OFF Soft start
5 VC
Reset OSC
+
VADJ
Comp.
+ +
ADJ
TSD
TSD
Error Amp.
GND 3
VREF
VREF GND 3
SI-8000FDE
+ C1 SS 5 C3 GND GND 3
SI-8001FDL
Vc 5 GND 3
GND
GND
GND
C1 C2 C3 L1 Di
: 470F : 680F : 0.1 (Only when using soft-start function) : 47H : SPB-G56S (Sanken)
C1 C2 L1 Di
ICs
29
*1: Limited by thermal protection circuit *2: This product has built-in thermal protection circuits that may activate when the junction temperature exceeds 130C. The recommended design for the junction temperature during IC operation is below 125C.
Applications
DVD recorder, FPD-TV Onboard local power supplies OA equipment
*1: The minimum value of the input voltage range is 4.5 V or Vo+3 V, whichever is higher.
Electrical Characteristics
Ratings Paramter Symbol min. Reference Voltage Temperature Coefficient of Reference Voltage Efficiency Oscillation Frequency Line Regulation Load Regulation Overcurrent Protection Starting Current Low Level Voltage SS Pin*1 Outflow Current at Low Voltage VADJ Conditions (VADJ/T) Conditions Conditions fo Conditions VOLINE Conditions VOLOAD Conditions IS Conditions VSSL ISSL Conditions Iq Quiescent Circuit Current Conditions Iq(OFF) Conditions 10 VSSL=0V 6 VIN=15V, Io=0A 200 VIN=15V, VSS=0V 5.6 0.784 SI-8008HD typ. 0.800 VIN=15V, Io=1A 0.1 VIN=15V, Io=1A, Tc=0 to 100C 83 VIN=15V, Io=3A 150 VIN=15V, Io=3A 60 VIN=10 to 30V, Io=3A 20 VIN=15V, Io=0.2 to 5.5A 6.5 VIN=15V
(R1=4.2k, R2=0.8k when Ta=25C and Vo=5V) Unit max. 0.816 V mV/C % kHz 80 50 7.5 0.5 30 mV mV A V A mA 400 A
*1: Pin 5 is the SS pin. Soft start at power on can be performed with a capacitor connected to this pin. The output can also be turned ON/OFF with this pin. The output is stopped by setting the voltage of this pin to VSSL or lower. SS-pin voltage can be changed with an open-collector drive circuit of a transistor. When using both the soft-start and ON/OFF functions together, the discharge current from C3 flows into the ON/ OFF control transistor. Therefore, limit the current securely to protect the transistor if C3 capacitance is large. The SS pin is pulled up (3.7 V typ.) to the power supply in the IC, so applying the external voltage is prohibited. If this pin is not used, leave it open.
SI-8008HD
SI-8008HD
SI-8008HD
5 SS
5 SS C3
5 SS C3
VO.ON/OFF
Soft start
30
ICs
SI-8000HD Series
(Unit : mm)
10.0
0.2
1.2
(15)
(6.8)
0.2
9.2
0.3
15.3
(3)
0.1
0.10 (3)
0.15
2.4 (R0.3)
0.3
0.2
2.0
15.30
0.3
9.2
0.2
1.5 Dp:
0.2
(3)
(2R0.45)
Pin Assignment 1 IN 2 SW 3 GND 4 ADJ 5 SS Plastic Mold Package Type Flammability: UL 94V-0 Product Mass: Approx. 1.48 g
(4.6)
0.2
(1.75)
(0.75)
4.9
0.88
0.10
(R0.3)
2.54
0 to 6 (0.5)
0.1
(1.7
0.25
) 1 2 3 4 9.9
0.2
0.1
(1.7
0.25
(3) 2-R0.3
10.0
0.02
Block Diagram
SI-8008HD 1 IN PReg. 5 SS
ON/OFF Soft start
4.9
0.2
SW OCP
Latch & Drive
Reset OSC
+
ADJ
Comp. Error Amp.
+ +
TSD
GND 3
VREF
Reference Data
The acceptable loss of the package is 3 W for the SI-8000HD series, so some ranges are not available, depending on the relation between the input voltage and output current.
SI-8008HD
+ C1 C4 SS 5 C3 GND GND 3
C2
GND
: 1500F : 1000F : 0.1F (Only when using soft-start function) : 4.7F (GMR32ER71H475KA88L (Murata Manufacturing) recommended) L1 : 100H Di : FMB-G16L (Sanken)
C1 C2 C3 C4
200
400
600
800
1000
1200
1400
1600
1800
ICs
31
SI-8000E Series
Features
Compact full-mold package (equivalent to TO220) High efficiency: 80% Requires only 4 discrete components
Internally-adjusted phase correction and output voltage Built-in reference oscillator (60kHz) Built-in overcurrent and thermal protection circuits
Applications
Power supplies for telecommunication equipment Onboard local power supplies
j-c j-a
Electrical Characteristics
Ratings Parameter Symbol VO Output Voltage Efficiency Oscillation Frequency Line Regulation Load Regulation Temperature Coefficient of Output Voltage Overcurrent Protection Starting Current Conditions min. 4.80 SI-8050E typ. 5.00 VIN=20V, IO=0.3A 80 VIN=20V, IO=0.3A 60 VIN=20V, IO=0.3A 80 VIN=10 to 30V, IO=0.3A 30 VIN=20V, IO=0.1 to 0.4A 0.5 0.61 VIN=10V 40 100 max. 5.20
(Ta=25C) Unit
V % kHZ mV mV mV/ C A
32
ICs
SI-8000E Series
(Unit : mm)
0.2
0.5
4.00.2 7.90.2
16.90.3
3.20.2
(17.9)
2.60.1
0.95
0.15 +0.2
0.85 0.1
+0.2
Pin Assignment q VIN w SWOUT e GND r VOS t N.C Plastic Mold Package Type Flammability: UL94V-0 Product Mass: Approx. 2.3g
(4.6)
3.90.7
(4.3) 8.20.7
1 2 3 4 5
Block Diagram
(8.0)
(2.0)
5V : 200H
VIN 1 OCP Reg. OSC Reset Drive Comp. 4 VOS TSD 2 SWOUT
VIN
2 VIN SWOUT
L1
VO
+ C1 100F
SI-8000E
VOS GND 3 NC 5 4
D1 AK06 (Sanken)
+ C2 330F
GND
GND
Ta-PD Characteristics
15
Infinite heatsink
PD=VOIO
10
10
0 10
The efficiency depends on the input voltage and the output current. Therefore, obtain the value from the efficiency graph and substitute the percentage in the formula above.
.3
20
Without heatsink
0 30 0 25
m (5 75 .2 7 C/ 5 W 2m ) m (7. 6 C/ W)
/ C W
Operating Ambient Temperature Ta (C) Thermal design for D1 must be considered separately.
20 0
0 2m
m 2m 0 (2 )
VO VIN IO x VF
100 125
: : : : :
50
75
Output voltage Input voltage Output current Efficiency (%) Diode D1 forward voltage 0.4V(AK06)
ICs
33
Lineup
Part Number VO (V)* IO (A) SI-8015JF 1.59 SI-8033JF 3.3 1.5 SI-8050JF 5.0 SI-8120JF 12.0
j-c
Applications
Power supplies for telecommunication equipment Onboard local power supplies
* SI-8015JF is a variable output voltage type. The variable output voltage range is from 2.5 V to 24 V.
Electrical Characteristics
Ratings Parameter Symbol min. Output Voltage*1 Efficiency Oscillation Frequency Line Regulation Load Regulation Temperature Coefficient of Output Voltage*3 Overcurrent Protection Starting Current ON/OFF*5 Terminal Low Level Voltage Outflow Current at Low Voltage VO*2 Conditions 1.558 SI-8015JF typ. 1.59 67 VIN=12V, IO=0.5A 125 VIN=12V, IO=0.5A 25 10 0.5 1.6 VIN=12V 0.5 100 VSSL=0V 7 VIN=12V, IO=0A 200 VIN=12V, VON/OFF=0.3V VSSL=0V 7 VIN=15V, IO=0A 200 VIN=15V, VON/OFF=0.3V 1.6 VIN=15V 0.5 100 VSSL=0V 7 VIN=20V, IO=0A 200 VIN=20V, VON/OFF=0.3V 80 30 VIN=8 to 30V, IO=0.5A VIN=12V, IO=0.2 to 0.8A max. 1.622 min. 3.234 SI-8033JF typ. 3.30 77 VIN=15V, IO=0.5A 125 VIN=15V, IO=0.5A 25 10 0.5 1.6 VIN=20V 0.5 100 VSSL=0V 7 VIN=24V, IO=0A 200 VIN=24V, VON/OFF=0.3V mA 80 30 VIN=8 to 30V, IO=1.0A VIN=15V, IO=0.5 to 1.5A max. 3.366 min. 4.90 SI-8050JF typ. 5.00 82 VIN=20V, IO=0.5A 125 VIN=20V, IO=0.5A 40 10 0.5 1.6 VIN=24V 0.5 100 A V 100 40 VIN=10 to 30V, IO=1.0A VIN=20V, IO=0.5 to 1.5A max. 5.10 min. 11.76 SI-8120JF typ. 12.00 88 VIN=24V, IO=0.5A 125 VIN=24V, IO=0.5A 60 10 1.0 130 mV mV mV/ C 40 VIN=18 to 30V, IO=1.0A VIN=24V, IO=0.5 to 1.5A kHZ % max. 12.24 V Unit
(Ta=25C)
VIN=12V, IO=0.5A
VIN=15V, IO=0.5A
VIN=20V, IO=0.5A
VIN=24V, IO=0.5A
Conditions f Conditions VOLINE Conditions VOLOAD Conditions VO/Ta*4 IS1 Conditions VSSL ISSL Conditions Iq Conditions Iq(OFF) Conditions
*3: Temperature Coefficient of Reference Voltage for SI-8015JF *4: VREF/Ta for SI-8015JF
*5: Pin 5 is the ON/OFF pin. Soft start at power on can be performed with a capacitor connected to this pin. The output can also be turned ON/OFF with this pin. The output is stopped by setting the voltage of this pin to VSSL or lower. ON/OFF-pin voltage can be changed with an open-collector drive circuit of a transistor. When using both the soft-start and ON/OFF functions together, the discharge current from C3 flows into the ON/OFF control transistor. Therefore, limit the current securely to protect the transistor if C3 capacitance is large. The ON/OFF pin is pulled up to the power supply in the IC, so applying the external voltage is prohibited. If this pin is not used, leave it open.
SI-8000JF
SI-8000JF
SI-8000JF
5 ON/OFF
5 ON/OFF C3
5 ON/OFF C3
VOUT. ON/OFF
Soft start
34
ICs
SI-8000JF Series
(Unit : mm)
4.20.2 0.2 2.8
4.00.2 7.90.2
16.90.3
3.20.2
(17.9)
2.60.1
(2.0)
0.95
0.15 +0.2
0.85 0.1
+0.2
(8.0)
Pin Assignment q VIN w SWOUT e GND r VOS t ON/OFF Plastic Mold Package Type Flammability: UL94V-0 Product Mass: Approx. 2.3g
4=6.8
0.7
3.90.7
(4.6)
(4.3) 8.20.7
1 2 3 4 5
Forming No.1101
Block Diagram
SI-8015JF 8033JF, 8050JF, 8120JF
SW OUT
SW OUT
5 ON/OFF Latch& Drive ON/OFF Soft Start VREF Comp. Error Amp.
+
Reset OSC
+
Latch& Drive
TSD
TSD
VREF
SI-8015JF
220F + VREF ON/OFF GND 5 3
SI-8000JF
C1 + ON/OFF GND 5 3 C3
VS
C2
GND
GND
GND
GND
IREF shall be approx. 2mA. C1 : C2 : C3 : C4 : L1 : Di : 50V/220F 25V/470F 10V/0.47F (Only when using soft-start function) 6800pF VREF (R1+R2) 100H VOUT= RK16 (Sanken) R2 C1 C2 C3 L1 Di : : : : : 50V/220F 25V/470F 10V/0.47F (Only when using soft-start function) 100H RK16 (Sanken)
IREF
ICs
35
Lineup
Part Number VO (V) IO (A) SI-8008TFE Variable (0.8 to 24) 1.5 SI-8050TFE 5
Applications
Onboard local power supplies AV equipment OA equipment
j-c j-a
*: This product has built-in thermal protection circuits that may operate when the junction temperature rises above 130C. The recommended design for the junction temperature during operation is below 125C.
8 to 40 5.0
V V A
C C
*1: The minimum value of an input voltage range is the higher of 4.5 V or VO + 3 V.
Electrical Characteristics
Ratings Parameter Symbol Ratings
(Ta=25C)
min.
Output Voltage (Reference Voltage) Temperature Coefficient of Output Voltage (Temperature Coefficient of Reference Voltage) Efficiency Oscillation Frequency Line Regulation Load Regulation Overcurrent Protection Starting Current Low Level Voltage ON/OFF Pin* Outflow Current at Low Voltage
max.
Vo (VADJ)
Conditions
min. 4.90
Unit
max. 5.10 V
0.784
Vo/T (VREF/T)
Conditions
Conditions
0.1 VIN=15V, Io=0.1A, Tc=0 to 100C 81 VIN=15V, Io=0.5A 300 VIN=15V, Io=0.5A 60 VIN=10 to 30V, Io=0.5A 10 VIN=15V, Io=0.2 to 1.5A
1.6
mV/C
VIN=15V, Io=0.1A, Tc=0 to 100C 81 VIN=15V, Io=0.5A 300 VIN=15V, Io=0.5A 60 VIN=10 to 30V, Io=0.5A 10 VIN=15V, Io=0.2 to 1.5A
1.6
% kHz
fo
Conditions
VOLINE
Conditions
80 40
80 40
mV mV A
VOLOAD
Conditions
IS
Conditions
VSSL ISSL
Conditions
V A mA A
Iq
Quiescent Circuit Current Conditions
Iq(OFF)
Conditions
*: Pin 5 is the SS pin. Soft start at power on can be performed with a capacitor connected to this pin. The output can also be turned ON/OFF with this pin. The output is stopped by setting the voltage of this pin to VSSL or lower. SS-pin voltage can be changed with an open-collector drive circuit of a transistor. When using both the soft-start and ON/OFF functions together, the discharge current from C3 flows into the ON/OFF control transistor. Therefore, limit the current securely to protect the transistor if C3 capacitance is large. The SS pin is pulled up to the power supply in the IC, so applying the external voltage is prohibited. If the pin is not used, leave it open.
SI-8000TFE
SI-8000TFE
SI-8000TFE
5 SS
5 SS C3
5 SS C3
VO.ON/OFF
Soft start
36
ICs
SI-8000TFE Series
(Unit : mm)
0.5
10.0
0.2
0.2
4.00.2 7.90.2
16.90.3
3.20.2
2.60.1
(2.0)
0.95
0.15 +0.2
Pin Assignment q IN w SW e GND r ADJ t SS Plastic Mold Package Type Flammability: UL94V-0 Product Mass: Approx. 2.3g
0.45 0.1
+0.2
3.90.7
(4.3) 8.20.7
1 2 3 4 5
Block Diagram
4.60.6
(4.6)
(17.9)
VIN
SW 2
IN
SW
2 R1
VOUT
SI-8000TFE
C1 220F + SS 5 C3 GND 3
ADJ 4 R2 Di IADJ
C2 470F
Comp.
+ +
GND
GND
GND 3
Error Amp.
Reference Voltage
C1 : 220F C2 : 470F C3 :1F (Only when using soft-start function) L1 : 47H Di : RK16 (Sanken)
ICs
37
SI-8000GL Series
Features
DIP 8 pin package Output current: 1.5A High efficiency: 86% (at VIN = 20V, lO = 1A, VO = 5V) Capable of downsize a choke-coil due to IC's high switching frequency (250kHz). (Compared with conventional Sanken devices) The output-voltage-variable type can vary its output voltage from 1V to 14V because of its low reference voltage (Vref) of 1V. Wide Input Voltage Range (8 to 50V) Output ON/OFF available Built-in overcurrent protection and thermal protection circuits
j-c j-a
Applications
Onboard local power supplies OA equipment For stabilization of the secondary-side output voltage of switching power supplies
*1: The minimum value of an input voltage range is the higher of either 8V or VO+3V. *2: Please be sure to let the output current run more than 20 mA. When using by less than 20 mA, there is a possibility that the output voltage becomes unstable.
Electrical Characteristics
Ratings Parameter Symbol min. Reference Voltage Efficiency Oscillation Frequency Line Regulation Load Regulation Temperature Coefficient of Reference Voltage Overcurrent Protection Starting Current Quiescent Circuit Current Circuit Current at Output OFF CE/SS* Terminal Low Level Voltage Terminal Outflow Current at Low Voltage VREF Conditions Eff Conditions FOSC Conditions VOLINE Conditions VOLOAD Conditions VREF/Ta IS Conditions Iq Conditions Iq(OFF) Conditions VSSL ISSL Conditions VSSL=0V VIN=12V, VON/OFF=0.3V 0.5 50 1.6 VIN=12V 7 VIN=12V, IO=0A 400 0.97 SI-8010GL (Variable type) typ. 1.00 VIN=12V, IO=1A 86 VIN=20V, IO=1A, VO=5V 250 VIN=12V, IO=1A 20 VIN=10 to 30V, IO=1A 10 VIN=12V, IO=0.1 to 1.5A 0.5 30 40 max. 1.03
(Ta=25C) Unit
V % kHZ mV mV mV/C A mA
A
V
*: Pin 2 is the CE/SS pin. Soft start at power on can be performed with a capacitor connected to this pin.The output can also be turned ON/OFF with this pin. The output is stopped by setting the voltage of this pin to VSSL or lower. CE/SS-pin voltage can be changed with an open-collector drive circuit of a transistor. When using both the soft-start and ON/OFF functions together, the discharge current from C4 flows into the ON/OFF control transistor. Therefore, limit the current securely to protect the transistor if C3 capacitance is large. The CE/SS pin is pulled up to the power supply in the IC, so applying the external voltage is prohibited.
SI-8000GL
SI-8000GL
SI-8000GL
2 CE/SS
2 CE/SS C4
2 CE/SS C4
VO. ON/OFF
Soft start
38
ICs
SI-8000GL Series
(Unit: mm)
9.40.3
4.20.3
7.50.5
7.6
Pin Assignment 1. GND 2. CE/SS 3. Reg 4. SWOUT 5. VIN 6. B.S 7. Comp 8. VREF Plastic Mold Package Type Flammability: UL 94V-0 Product Mass: Approx. 0.49 g
3.40.1
+0.1 0.25-0. 05
3.30.2
0.25 M 0 to 15
Block Diagram
SI-8010GL
Ta-PD Characteristics
2 1.8
PD=VO IO
100 VO 1 VF IO 1 VIN
VIN
P.REG
OCP BS
PWM LOGIC
SWOUT
Note 1: The efficiency depends on the input voltage and the output current. Therefore, obtain the value from the efficiency graph and substitute the percentage in the formula above. Note 2: Thermal design for D1 must be considered separately.
25 50 75 100 125
VREF Comp
Amp +
0 25
GND
VO : Output voltage VIN : Input voltage IO : Output current : Efficiency VF : Diode D1 forward voltage RK160.4V(IO=1A)
B.S
5
R1 L1 C3
VIN
2 C1
VIN CE/SS
C7
SI-8010GL
Comp
7 C5 C6
SWOUT
4 D1 R2
V0
Reg
3 C4
GND
1
VREF
+
C2 C8 IREF
8 R3
C1: 220F/63V C2: 470F/25V C3: 0.1F C4: 1000pF C5: 0.1F C6: 0.047F C7: 0.1F
VREF (VOUTVREF) (VOUT1) 1 . GND = = (), R3 = R2= = . 500() 2103 IREF 2103 IREF Diode D1 Be sure to use a Schottky-barrier diode as D1. If other diodes like fast recovery diodes are used, IC may be destroyed because of the reverse voltage generated by the recovery voltage or ON voltage. Choke coil L1 If the winding resistance of the choke coil is too high, the efficiency may drop below the rated value. As the overcurrent protection starting current is approx. 2.5 A, take care concerning heat radiation from the choke coil caused by magnetic saturation due to overload or short-circuited load. Capacitor C1, C2 As large ripple currents flow through C1 and C2, use high-frequency and low-impedance capacitors aiming for switching-mode-power-supply use. Especially when the impedance of C2 is high, the switching waveform may become abnormal at low temperatures. For C2, do not use a capacitor with an extremely low equivalent series resistance (ESR) such as an OS capacitor or a tantalum capacitor, which may cause an abnormal oscillation. Resistors R2, R3 R2 and R3 are the resistors to set the output voltage. Set their values so that IREF becomes approx. 2 mA. Obtain R2 and R3 values by the following formula above.
GND
* To create the optimum operating conditions, place the components as close as possible to each other.
ICs
39
Lineup
Part Number VO(V) IO(A) SI-8033S 3.3 SI-8050S 5.0 SI-8090S 9.0 3.0 SI-8120S 12.0 SI-8150S 15.0
j-c
Applications
Power supplies for telecommunication equipment Onboard local power supplies
Electrical Characteristics
Ratings Parameter SI-8000S*1 Output Voltage SI-8000SS VO Conditions Efficiency Oscillation Frequency Line Regulation Load Regulation Temperature Coefficient of Output Voltage Overcurrent Protection Starting Current Symbol min. 3.17 3.234 SI-8033S typ. 3.30 3.30 79 VIN=15V, IO=1.0A 60 VIN=15V, IO=1.0A 25 10 80 30 VIN=8 to 28V, IO=1.0A VIN=15V, IO=0.5 to 1.5A 0.5 3.1 VIN=15V 3.1 VIN=20V max. 3.43 3.366 min. 4.80 4.90 SI-8050S typ. 5.00 5.00 84 VIN=20V, IO=1.0A 60 VIN=20V, IO=1.0A 40 10 100 40 VIN=10 to 30V, IO=1.0A VIN=20V, IO=0.5 to 1.5A 0.5 3.1 VIN=21V max. 5.20 5.10 VIN=21V, IO=1.0A 88 VIN=21V, IO=1.0A 60 VIN=21V, IO=1.0A 50 10 120 40 VIN=15 to 30V, IO=1.0A VIN=21V, IO=0.5 to 1.5A 1.0 3.1 VIN=24V VIN=24V, IO=1.0A 90 VIN=24V, IO=1.0A 60 VIN=24V, IO=1.0A 60 10 130 40 VIN=18 to 30V, IO=1.0A VIN=24V, IO=0.5 to 1.5A 1.0 3.1 VIN=25V VIN=25V, IO=1.0A 91 VIN=25V, IO=1.0A 60 VIN=25V, IO=1.0A 60 10 130 VIN=21 to 30V, IO=1.0A 40 VIN=25V, IO=0.5 to 1.5A 1.0 min. 8.55 SI-8090S typ. 9.00 max. 9.45 min. 11.50 SI-8120S typ. 12.00 max. 12.50 min. 14.25 SI-8150S typ. 15.00 max. 15.75
(Ta=25C) Unit
VIN=15V, IO=1.0A
VIN=20V, IO=1.0A
% kHZ mV mV mV/ C A
*1: S may be printed to the right of the marking (except SI-8090S, SI-8120S, SI-8150S).
40
ICs
SI-8000S Series
(Unit : mm)
4.2 2.80.2
0.2
10.0
0.2
4.00.2 7.90.2
16.90.3
3.20.2
(17.9)
2.60.1
(2.0)
+0.2
Pin Assignment q VIN w SWOUT e GND r VOS t S.S Plastic Mold Package Type Flammability: UL94V-0 Product Mass: Approx. 2.3g
3.90.7
(4.3) 8.20.7
1 2 3 4 5
Block Diagram
VIN 1 Reg. OSC Reset OCP 2 SWOUT
Drive
Comp.
TSD 4 VOS
Amp.
VREF
5 S.S.
3 GND
(8.0)
+ C1
SI-8000S
VOS S.S 5 GND 3 4
D1
+ C2
GND
GND
Ta-PD Characteristics
20 Infinite heatsink
PD=VOIO
With Silicone Grease Heatsink: Aluminum
100 1
VFIO 1
VO VIN
15
2002002mm (2.3C/W)
The efficiency depends on the input voltage and the output current. Therefore, obtain the value from the efficiency graph and substitute the percentage in the formula above. VO VIN IO x VF : : : : : Output voltage Input voltage Output current Efficiency (%) Diode D1 forward voltage 0.5V(RK46)
ICs
41
*1: Limited by thermal protection circuit *2: Note that the detect temperature for thermal protection is about 140C.
Applications
DVD recorder, FPD-TV Onboard local power supplies OA equipment
*1: The minimum value of the input voltage range is 4.75 V or Vo +3 V, whichever is higher.
Electrical Characteristics
Ratings
(When Ta=25C and Vo=5V) Symbol min. VADJ Conditions (VADJ/T) Conditions Conditions fo Conditions VoLINE Conditions VoLOAD Conditions Is Conditions Iq Conditions Iq(OFF) Conditions VIN=12V, Io=0A, VEN=0V 5 Conditions VC/EH Conditions VC/EL Conditions IC/EH Conditions AEA GEA 1/GCS DMAX DMIN VIN=12V 5 VEN=0V 1000 800 0.35 92 100 2.8 VIN=12V 2.2 VIN=12V, VSSL=0V ISSL 3.6 VIN=12V 18 VIN=12V, Io=0A, VEN=open 20 315 0.485 SI-8105QL typ. 0.500 VIN=12V, Io=1A 0.05 VIN=12V, Io=1A, Ta=40 to +85C 90 VIN=12V, Io=1A 350 VIN=16V, Io=1A 30 VIN=8 to 28V, Io=1A 30 VIN=12V, Io=0.1 to 3.5A 6.0 60 60 385 max. 0.515 V mV/ C % kHz mV mV A mA A A V V A V/V A/V V/A % nsec. Unit
Parameter
Reference Voltage Temperature Coefficient of Reference Voltage Efficiency Oscillation Frequency Line Regulation Load Regulation Overcurrent Protection Starting Current
SS Pin
EN Pin
Error Amplifier Voltage Gain Error Amplifier Transformer Conductance Current Sense Amplifier Impedance Maximum ON Duty Minimum ON Time
*: Pin 8 is the SS pin. Soft start at power on can be performed with a capacitor connected to this pin. The SS pin is pulled up to the power supply in the IC, so applying the external voltage is prohibited.
SI-8100QL
8 SS C5
Soft start
42
ICs
SI-8100QL Series
(Unit : mm)
6.50.2
4.20.3
3.40.1
7.50.5
7.6
Pin Assignment 1 BS 2 IN 3 SW 4 GND 5 FB 6 COMP 7 EN 8 SS Plastic Mold Package Type Flammability: UL 94V-0 Product Mass: Approx. 0.49 g
+0.1 0.25-0. 05
0.50.1
3.30.2
0.25 M 0 to 15
Block Diagram
2 IN
OSC 5v_ldo
P.REG VREF
0.5V 7 EN ON OFF
Drive 3 SW 5v_ldo
6 COMP UVLO
Amp 0.5V
5 FB
4 GND
8 SS
2 IN EN SI-8105QL
1 BS
VO
C1 C5
SS
COMP 6 C3
GND
C6 OPEN
R3
GND
ICs
43
Lineup
Part Number Vo (V) Io (A) Function SI-8001FFE
Applications
DVD recorder, FPD-TV OA equipment, such as printers Onboard local power supplies
*: This product has built-in thermal protection circuits that may activate when the junction temperature exceeds 130C. The recommended design for the junction temperature during IC operation is below 125C.
*: The minimum value of the input voltage range is 4.5 V or Vo +3 V, whichever is higher.
Electrical Characteristics
Ratings Parameter Symbol min. Reference Voltage Temperature Coefficient of Reference Voltage Efficiency Oscillation Frequency Line Regulation Load Regulation Overcurrent Protection Starting Current Low Level Voltage SS Pin Outflow Current at Low Voltage VADJ Conditions VADJ/T Conditions Conditions fo Conditions VOLINE Conditions VOLOAD Conditions IS Conditions VSSL ISSL Conditions Iq Quiescent Circuit Current Conditions Iq(OFF) Conditions 6 VIN=15V, VSS=0V 6 VIN=15V, Io=0A 200 VIN=15V, Vss=0V 3.6 VIN=15V 270 0.784 SI-8001FFE typ. 0.800 VIN=15V, Io=0.2A 0.1
(R1=4.2k, R2=0.8k when Ta=25C and Vo=5V) Unit max. 0.816 V mV/ C % 330 80 50 kHz mV mV A 0.5 30 V A mA 600 A
VIN=15V, Io=0.2A, Tc=0 to 100C 83 VIN=15V, Io=2A 300 VIN=15V, Io=2A 55 VIN=10 to 30V, Io=2A 15 VIN=15V, Io=0.2 to 3.5A
*: Pin 5 is the SS pin. Soft start at power on can be performed with a capacitor connected to this pin. The output can also be turned ON/OFF with this pin. The output is stopped by setting the voltage of this pin to VSSL or lower. SS-pin voltage can be changed with an open-collector drive circuit of a transistor. When using both the soft-start and ON/OFF functions together, the discharge current from C3 flows into the ON/ OFF control transistor. Therefore, limit the current securely to protect the transistor if C3 capacitance is large. The SS pin is pulled up (3.7 V typ.) to the power supply in the IC, so applying the external voltage is prohibited. If this pin is not used, leave it open.
SI-8000FFE
SI-8000FFE
SI-8000FFE
5 SS
5 SS C3
5 SS C3
VO.ON/OFF
Soft start
44
ICs
SI-8000FFE Series
(Unit : mm)
0.5
10.0
0.2
0.2
4.00.2 7.90.2
3.20.2
16.90.3
0.45 0.1
+0.2
3.90.7
(4.3) 8.20.7
1 2 3 4 5
Block Diagram
SW
TSD
GND 3
VREF
SI-8001FFE
+ C1 SS 5 C3 GND GND 3
GND
C1 C2 C3 L1 D1
ICs
45
Lineup
Part Number VO (V) IO (A) SI-8008HFE Variable (0.8 to 15) 5.5 SI-8050HFE 5
Applications
Onboard local power supplies OA equipment
j-c j-a
*: This product has built-in thermal protection circuits that may operate when the junction temperature rises above 130C. The recommended design for the junction temperature during operation is below 125C.
8 to 40 5.0
V V A
C C
*1: The minimum value of an input voltage range is the higher of 4.5 V or VO + 3 V.
Electrical Characteristics
Ratings Parameter Symbol Ratings
(Ta=25C)
SI-8008HFE (at Vo = 5 V) max. min. typ. 0.784 0.800 VIN=15V, Io=1A 0.816
Output Voltage (Reference Voltage) Temperature Coefficient of Output Voltage (Temperature Coefficient of Reference Voltage) Efficiency Oscillation Frequency Line Regulation Load Regulation Overcurrent Protection Starting Current Low Level Voltage ON/OFF Pin* Outflow Current at Low Voltage
Vo (VADJ)
Conditions
min. 4.90
Unit
max. 5.10 V
Vo/T (VADJ/T)
Conditions
Conditions
0.1 VIN=15V, Io=1A, Tc=0 to 100C 83 VIN=15V, Io=3A 150 VIN=15V, Io=3A 60 VIN=10 to 30V, Io=3A 20 VIN=15V, Io=0.2 to 5.5A
5.6
VIN=15V, Io=1A, Tc=0 to 100C 83 VIN=15V, Io=3A 150 VIN=15V, Io=3A 60 VIN=10 to 30V, Io=3A 20 VIN=15V, Io=0.2 to 5.5A
5.6
% kHz
fo
Conditions
VOLINE
Conditions
80
50
80 50
mV mV A
VOLOAD
Conditions
IS
Conditions
VSSL ISSL
Conditions
V A mA A
Iq
Quiescent Circuit Current Conditions
Iq(OFF)
Conditions
*: Pin 5 is the SS pin. Soft start at power on can be performed with a capacitor connected to this pin. The output can also be turned ON/OFF with this pin. The output is stopped by setting the voltage of this pin to VSSL or lower. SS-pin voltage can be changed with an open-collector drive circuit of a transistor. When using both the soft-start and ON/OFF functions together, the discharge current from C3 flows into the ON/OFF control transistor. Therefore, limit the current securely to protect the transistor if C3 capacitance is large. The SS pin is pulled up to the power supply in the IC, so applying the external voltage is prohibited. If the pin is not used, leave it open.
SI-8000HFE
SI-8000HFE
SI-8000HFE
5 SS
5 SS C3
5 SS C3
VOUT. ON/OFF
Soft start
46
ICs
SI-8000HFE Series
(Unit : mm)
0.5
10.0
0.2
0.2
16.90.3
(17.9)
2.60.1
(2.0)
+0.2
4.60.6
Pin Assignment q VIN w SW e GND r ADJ (VOS for SI-8050HFE) t SS Plastic Mold Package Type Flammability: UL94V-0 Product Mass: Approx. 2.3g
0.7
(4.3) 8.20.7
1 2 3 4 5
Block Diagram
SI-8050HFE
IN PReg.
Overcurrent Protection
SW
5 ON/OFF
ON/OFF Soft Start
Reset OSC
Comp.
+ +
Thermal Protection
Vos 4
Error Amp.
GND 3
Reference Voltage
VIN C1 +
1 C4
IN PReg.
SW
2 Di
VOUT + C2
VIN C1 +
1 C4
IN PReg.
SW
2 Di
VOUT + C2
5 ON/OFF R1 SI-8008HFE C3
+
5 ON/OFF
SI-8050HFE C3 ADJ 4
+
ADJ 4
+ +
R2
GND 3
GND 3
C1 C2 C3 C4 L1 Di
: 1500F : 1000F :1F (Only when using soft-start function) :4.7F (RPER11H475K5 (Murata Manufacturing) recommended) :100H : FMB-G16L (Sanken)
ICs
47
SI-8000Y Series Current Full-Mold, Mode Separate Control Excitation Step-down Step-down Switching Switching ModeMode Regulator ICs
Features
Compact (equivalent to TO220) full-mold package Output current: 8.0 A High efficiency: 86% Built-in reference oscillator (130 kHz) Built-in drooping-type-overcurrent protection and thermal protection circuits Built-in soft start circuit (Output ON/OFF available) Low current consumption during off
Power Dissipation Junction Temperature Storage Temperature Thermal Resistance (Junction to Case) Thermal Resistance (Junction to Ambient Air)
Applications
AV equipment OA equipment Gaming equipment Onboard local power supplies
*: The minimum value of the input voltage range is 8 V or Vo + 3V, whichever is higher.
Electrical Characteristics
Ratings Parameter Output Voltage (Reference voltage for SI-8010Y) (Reference voltage temperature coefficient for SI-8010Y) Efficiency Oscillation Frequency Line Regulation Load Regulation Overcurrent Protection Starting Current Symbol mIN. VO(VREF) Conditions Conditions Conditions fo Conditions 0.98 SI-8010Y* typ. 1.00 VIN=30V, Io=0.1A 0.1 VIN=30V, Io=0.1A, Ta=0 to 100C 86 VIN=30V, Io=3A 130 VIN=30V, Io=3A 30 VIN=10 to 43V, Io=3A 30 VIN=30V, Io=0.1 to 8A 8.1 VIN=20V 8 VIN=30V, Io=0A, EN/SS=open 200 VIN=30V, EN/SS=0V 10 VIN=30V, EN/SS=0V 0.5 VIN=30V 300 800 0.16 92 200 VIN=30V 300 800 0.16 92 200 30 500 8.1 VIN=20V 8 VIN=30V, Io=0A, EN/SS=open 200 VIN=30V, EN/SS=0V 10 VIN=30V, EN/SS=0V 0.5 30 500 90 90 max. 1.02 mIN. 4.90 SI-8050Y typ. 5.00 VIN=30V, Io=0.1A 0.5 VIN=30V, Io=0.1A, Ta=0 to 100C 86 VIN=30V, Io=3A 130 VIN=30V, Io=3A 30 VIN=10 to 43V, Io=3A 30 VIN=30V, Io=0.1 to 8A 90 90 max. 5.10 V mV/C % kHz mV mV A mA Unit
VOLINE
Conditions
VOLOAD
Conditions Is Conditions Iq Conditions Iq(OFF) Conditions ISSL Conditions VSSL Conditions AEA GEA 1/GCS DMAX DMIN
A A
V V/V
A/V
V/A % nsec
SI-8000Y
SI-8000Y
5 SS C6
5 SS C6
Soft start
48
ICs
SI-8000Y Series
(Unit : mm)
4.20.2 2.80.2
4.00.2
7.90.2
16.90.3
3.20.2
(5.3)
Pin Assignment q BS w SW e VIN r GND t COMP y FB u EN/SS Plastic Mold Package Type Flammability: UL94V-0 Product Mass: Approx. 2.3g
2.8
17.60.7
+0.2
3.60.5
0.5
0.5
1 234 567
Plan View
Block Diagram
SI-8010Y
3 IN Current Sence Amp Boot 5vREG BS Current Sence Amp Boot 5vREG BS
SI-8050Y
3 IN
Pre REG
OSC
Pre REG 1
OSC
EN/ SS EN/SS
DRIVE SW
EN/ SS EN/SS
DRIVE SW
5 COMP
6 1.0V FB
5 COMP
6 1.0V FB
Amp
SI-8010Y
SI-8050Y
COMP 5
COMP 5
SI-8010Y C1:2200F/50V C2:4.7F/50V C3:470F/25V C4:1200pF C5:0.22F/50V C7:680pF L1:47H D1:FMW-2156 (Sanken) R1:8k (When Vo=5V) R2:2k R3:39k
SI-8050Y C1:2200F/50V Csn1,2=2200pF (When Vin>40V) C2:4.7F/50V Rsn1,2=10 (When Vin>40V) C3:470F/25V C4:1200pF C5:0.22F/50V C7:680pF L1:56H D1:FMW-2156 (Sanken) R3:39k
ICs
49
SI-8205NHD Full-Mold, Surface-Mount, Separate CurrentExcitation Mode Control, Step-down Synchronous Switching Rectifier Mode Step-down Regulator Switching ICs Mode
Features
Compact surface-mount (HSOP8) package Wide input voltage range (VIN): Vo + 3 to 43 V Synchronous rectifier mode Output current: 3 A Reference voltage and accuracy of 0.5 V 1% Oscillation frequency: 200 kHz to 1 MHz A ceramic capacitor can be used for output Output can be disabled Undervoltage Lock Out Soft start function
Input Voltage (VIN Pin) Power Dissipation Junction Temperature Storage Temperature Thermal Resistance (Junction to Lead <1 pin>) Thermal Resistance (Junction to Ambient Air)
V W C C C/W C/W
Applications
Power supply for LCD module Power supply for notebook PC Onboard local power supplies Power supply for LBP/PPC
Input Voltage Range Output Current Range Output Voltage Range Operating Junction Temperature Range Operating Temperature Range
Unit V A V C C
*: The minimum value of the input voltage range is 8 V or Vo + 3V, whichever is higher.
Electrical Characteristics
Parameter Reference Voltage Temperature Coefficient of Reference Voltage Efficiency Oscillation Frequency 1 Oscillation Frequency 2 Line Regulation Load Regulation Overcurrent Protection Starting Current Quiescent Circuit Current Outflow Current at Low Voltage EN/SS Pin Open Voltage On Threshold Voltage OVP Start Voltage Thermal Protection Start Temperature Error Amplifier Voltage Gain Error Amplifier Transformer Conductance Current Sense Amplifier Impedance Maximum ON Duty Minimum ON Time Symbol Vref VREF/T
min. 0.495
fo1 fo2 VoLINE VoLOAD Is IIN IIN(OFF) IEN/SS VSSH VC/EH Vovp Tj AEA GEA GCS DMAX DMIN
max. 0.505
Conditions VIN=12V, Io=1.0A VIN=12V, Io=1.0A, Ta=40 to +85C VIN=12V, Vo=5V, Io=1.0A VIN=12V, Vo=5V, Io=1A, Rfset=375k VIN=12V, Vo=5V, Io=1A, Rfset=75k VIN=8 to 43V, Vo to 5V, Io=1A VIN=12V, Vo=5V, Io=0.1 to 3.0A VIN=12V, Vo=5V VIN=12V, Vcomp=0V VIN=12V, VEN/ss=0V VEN/SS=0V, VIN=12V VIN=12V VIN=12V
3.1
6.0 40
80
V V V
C
VIN=12V VIN=12V
50
ICs
SI-8205NHD
(Unit : mm)
4.40
6.20
Pin 1 Mark
Enlarged View of A
1.27 0.40
0.4
Pin Assignment q GND w EN/SS e VIN r FSET t COMP y FB u BS i SW Plastic Mold Package Type Flammability : UL 94V-0 Product Mass : Approx. 0.1 g
0.050.05 0.15
2.90
Block Diagram
VIN
+ REG
2.70
0.080.08
CUR_SUS DRV_REG
REG_DRV REG REG OVC REG_DEV REG_DEV
REG
BS
STANDBY
OCP_CMP
VinOK
BC
H/S Drv
Level Shift
REG_UVLO
M1
VIN_UVLO
PWR_stage
REG VinOK REG REG VinOK Set PH Fere Off Phase
SW
M2 GATE_logic
Level Shift LSoft STANDBY REG VinOK PH Open REG OVT
OSC_RAMP FSET
Ramp FB
REG
Phase_ logic
INIT PH INIT CC
L/S Drv
Res PH
CUR_COMP
REG
LSoft
BS_CHG
Control_logic
OVT
TSD
BG REG
OVP_CMP
REG
SS_Ref
REG
BG
Ref
FB Err_AMP
Rnf SS_Rnf
EN_SS
STANDBY
REF
GND COMP
R5 C4 7 8 BS SW 6 R1
L1
VO
C1
SI-8205NHD
FSET GND 1 R4 FB COMP 5 C3 C6 Open R3
C2 GND
C5 GND
R2 D1
ICs
51
NR885K Surface-Mount, Full-Mold, Current Separate Mode Excitation Control, Synchronous Step-down Switching Rectifier Step-down Mode Regulator Switching ICs Mode
Features
Compact surface-mount package (HSOP8) Input voltage range (VIN): VO + 3 to 18 V Synchronous rectifier mode High efficiency of at least 94% Introduction of current mode control method A ceramic capacitor can be used for output Built-in phase correction component Output current: 3 A Reference voltage and accuracy of 0.8 V 2% Oscillation frequency: 350 kHz Output ON/OFF available Undervoltage lockout Soft start function
Input Voltage Power Dissipation Junction Temperature Storage Temperature Thermal Resistance (Junction to Lead (4 pins)) Thermal Resistance (Junction to Ambient Air)
V W C C C/W C/W
Input Voltage Range Output Current Range Output Voltage Range Operating Temperature Range
Unit V A V C
*: The minimum value of the input voltage range is 4.5 V or VO + 3 V, whichever is higher.
Applications
Power supply for LCDTV and PDP Power supply for DVD, BD, and STB On-board local power supply Power supply for LBP and PPC
Electrical Characteristics
Parameter Reference Voltage Temperature Coefficient of Reference Voltage Efficiency Oscillation Frequency Line Regulation Load Regulation Overcurrent Protection Starting Current Quiescent Circuit Current 1 Quiescent Circuit Current 2 Outflow Current at Low Voltage SS Pin Open Voltage Inflow Current EN Pin On Threshold Voltage Maximum ON Duty Minimum ON Time Thermal Protection Start Temperature Thermal Protection Return Hysteresis Symbol VREF VREF/T
min. 0.784
fo VLINE VLoad Is IIN IIN(off) IEN/SS VSSH IEN VC/EH DMAX DMIN TSD TSD_hys
280
max. 0.816
Conditions VIN=12V Io=1.0A VIN=12V Io=1.0ATa=40 to +85 VIN=12V, Vo=3.3V, Io=1A VIN=12V, Vo=3.3V, Io=1A VIN=12V, Vo=3.3V, Io=1A VIN=6.3V to 18V, Vo=3.3V, Io=1A VIN=12V, Vo=3.3V VIN=12V, VEN=3V VIN=12V, Io=0A, VEN=0V VSS=0V, VIN=12V VIN=12V VEN=10V VIN=12V
420
3.1 0 6
0.7
151
*: Pin 8 is the SS pin. Soft start at power on can be performed with a capacitor connected to this pin. The SS pin is pulled up to the power supply in the IC, so applying the external voltage is prohibited.
NR885K
SS C9
Soft start
52
ICs
NR885K
(Unit : mm)
0.050.05
4.40
6.20
Pin 1 Mark
0.080.08
Enlarged View of A
1.27 0.40
0.4
Pin Assignment q BS w VIN e SW r GND t FB y NC u EN i SS *: The heat slug on the rear side is at the ground potential. Plastic Mold Package Type Flammability: UL 94V-0 Product Mass: Approx. 0.1g
2.90
Block Diagram
2 IN
OSC
2.70
OCP
0.15
SW 3
TSD
VIN
R3 C10 SW 3 L1
2 VIN 7 EN C2 C1 8 SS GND 4
1 BS
Vout
NR885K
FB NC 6 5
R4
C4 C5
R5
C9 R6 D1
C1, C2: 10F/25V C4, C5: 22F/16V C9: 0.1F C10: 0.1F L1: 10H R3: 20 to 47 R4+R5: 5k(VO=3.3V) R6: 1.6k
Option
ICs
53
Lineup
Part Number VO(V) IO(A) SI-8401L 5.0 0.5 SI-8501L 5.0 1.0
Applications
Telephone power supplies Onboard local power supplies
Parameter DC Input Voltage Range Output Current Range Operating Temperature Range
Unit V A C
Electrical Characteristics
Ratings Parameter Symbol min. Output Voltage Efficiency Oscillation Frequency Line Regulation Load Regulation Temperature Coefficient of Output Voltage Switching Ripple Voltage (C2=470F) Overcurrent Protection Starting Current VO Conditions 4.80 SI-8401L typ. 5.00 VIN=20V, IO=0.3A 80 VIN=20V, IO=0.3A 60 VIN=20V, IO=0.3A 80 VIN=10 to 30V, IO=0.3A 30 VIN=20V, IO=0.1 to 0.4A 0.5 20 VIN=20V, IO=0.3A 0.55 VIN=10V 40 40 100 max. 5.20
(Ta=25C) Unit
Conditions f Conditions VOLINE Conditions VOLOAD Conditions VO/Ta Vr Conditions IS1 Conditions
Ratings Parameter Symbol min. Output Voltage Efficiency Oscillation Frequency Line Regulation Load Regulation Temperature Coefficient of Output Voltage Switching Ripple Voltage (C2=470F) Overcurrent Protection Starting Current VO Conditions 4.80 SI-8501L typ. 5.00 VIN=20V, IO=0.5A 83 VIN=20V, IO=0.5A 60 VIN=20V, IO=0.5A 70 VIN=10 to 30V, IO=0.5A 30 VIN=20V, IO=0.2 to 0.8A 0.5 45 VIN=20V, IO=0.5A 1.1 VIN=18V A mVp-p 55 mV mV/ C 130 mV kHZ % max. 5.20 V Unit
Conditions f Conditions VOLINE Conditions VOLOAD Conditions VO/Ta Vr Conditions IS1 Conditions
54
ICs
SI-8400L/8500L Series
e LIN
w GND Vo q 14.5
0.5
Pin 1 marking
26
0.1
SK
100.2 13.20.6
0.6
0.8max.
(2.17) (10.16)
4.7
0.6
4
3.7
18
(7.62)
(2.19)
18
Block Diagram
SI-8400L
3 4 VIN Reg. OSC Reset OCP Latch & Drive TSD Di1 Amp.
Amp.
SI-8500L
LIN L1 1 VO
6 VIN Reg. OSC Reset OCP Latch & Drive TSD Di1 MIC1
4
LIN L1 1 VO
MIC1
Comp.
Comp.
VREF
VREF
GND
S.S.
GND
C2 470F
C2 470F
GND
GND
Ta-PD Characteristics
1.5
3.0
SI-8400L
SI-8500L
PD=VOIO
100 1
1.0
2.0
VO : Output voltage IO : Output current : Efficiency (%) The efficiency depends on the input voltage and the output current. Therefore, obtain the value from the efficiency graphs and substitute the percentage in the formula above.
0.5
1.0
0 0
25
50
75
100
0 0
25
50
75
100
ICs
55
Lineup
Output Voltage (V) Ch2(Select one output) 9.0 / 11.5 / 12.1 / 15.5
Applications
For BS and CS antenna power supplies For stabilization of the secondary stage of switching power supplies Electronic equipment
Electrical Characteristics
Ratings Parameter Symbol min. Ch1 Output voltage 1 Efficiency * Temperature Coefficient of Output Voltage Line Regulation Load Regulation Ch2 (Select one output) Output voltage 2-2 Output voltage 2-3 Output voltage 2-4 VO2-4 Efficiency* Temperature Coefficient of Output Voltage Line Regulation Load Regulation Common No-load Circuit Current Oscillation Frequency Overcurrent Protection Starting Current Output voltage 2-1 VO1 Conditions 4.80 STA801M typ. 5.00 VIN=20V, IO=0.3A 80 VIN=20V, IO=0.3A 0.5 30 VIN=10 to 30V, IO=0.3A 10 VIN=20V, IO=0.1 to 0.4A 8.64 11.04 11.62 14.88 9.00 VIN=20V, IO=0.3A 11.50 VIN=20V, IO=0.3A 12.10 VIN=20V, IO=0.3A 15.50 VIN=20V, IO=0.3A 89 VIN=20V, IO=0.3A 2.0 40 VIN=20 to 30V, IO=0.3A 30 VIN=20V, IO=0.1 to 0.4A 15 125 0.51 0.7 120 130 16.12 12.58 11.96 9.36 40 90 max. 5.20
(Ta=25C)
Unit
1
Conditions VO/Ta1 VOLINE1 Conditions VOLOAD1 Conditions VO2-1 Conditions VO2-2 Conditions VO2-3 Conditions VO2-4 Conditions
* Efficiency indicates the value when only one channel is active. The value can be calculated as shown below. 7.5mA is deducted for the no-load circuit current of output.
Icc at unused 2
VOIO VIN(IIN0.0075)
100(%)
56
ICs
STA801M
(Unit : mm)
3.150.5 (1)
90.2
1.20.1 2(R1)
.65)
2(R0
+0.2
9P2.540.5=22.861
Pin Assignment q VO2 Cont w VOS1 e SS1 r SWOUT1 t GND y VIN u SWOUT2
i SS2 o VOS22 !0 VOS21 Plastic Mold Package Type Flammability: UL94V-0 Product Mass: Approx. 2.5g
1 2 3 4 5 6 7 8 9 10
Block Diagram
VIN 6 P.Reg. OCP
4 SW1
SS1 3
+ PWM
PWM Logic
Drive
2 VOS1
+ Amp.
PWM OSC
Vref
f/4 Reset
TSD
4 SW2
OCP
SS2 8
+ PWM
PWM Logic
10 VOS2 1
Drive
9 VOS2 2
+ Amp.
Vref
Selection of connection method and output for VOS2-1 and VOS2-2 of Channel 2
SWOUT1 4 L1 5V:100 H C2 + VO1
7
6 C1 220F
VIN
STA801M
9 10
Vo2 9v
STA801M
+ 10
Vo2 11.5v
Ch 1 VOS1 2
330F
C4 0.47 F 8
Vo2Cont
12.1V
Vo2Cont
15.5V
SS2 Ch 2
SWOUT2 VOS2 2
7 10 Or
VOS2 1 9
9V 11.5V
12.1V 15.5V
Ta-PD Characteristics
7 6 With Infinite Heatsink
5 4 3 2 1 0 30
Without Heatsink
25
50
75
100
125
ICs
57
j-c j-a
*1: Absolute maximum ratings show the destructive limit. No parameter should exceed the ratings in transient or normal operations. *2: When mounted on glass-epoxy board 70cm2 (copper laminate area 30.8cm2). *3: Limited by thermal protection.
Applications
Onboard local power supplies OA equipment For stabilization of the secondary-side output voltage of switching power supplies
*1: Recommended operating conditions show the operating conditions required for the normal circuit function described in the electrical characteristics. These conditions must be followed in actual use.
58
ICs
SPI-8001TW/SPI-8002TW/SPI-8003TW
Electrical Characteristics*1
Ratings Parameter Symbol min. Reference Voltage Temperature Coefficient of Reference Voltage Efficiency 1*2 Efficiency 2*2 Oscillation Frequency Line Regulation Load Regulation Overcurrent Protection Starting Current Quiescent Circuit Current 1 Quiescent Circuit Current 2 Quiescent Circuit Current 3 Quiescent Circuit Current 4 Quiescent Circuit Current 5 Quiescent Circuit Current 6 High Level Voltage C/E Pin Low Level Voltage Inflow Current at High Low Level Voltage SS Pin*3 Inflow Current at Low VREF Conditions VREF/T Conditions Eff1 Conditions Eff2 Conditions fosc Conditions VLINE Conditions VLOAD Conditions IS Conditions IIN Conditions ICC Conditions IIN (off) Conditions ICC (off) Conditions IIN (ssov) Conditions ICC (ssov) Conditions VC/EH Conditions VC/EL Conditions IC/EH Conditions VSSL Conditions ISSL Conditions 60 0.5 VIN=VCC=15V 80 VSSL=0V, VIN=VCC=15V 60 80 95 VC/E=20V 0.5 VIN=VCC=14V 60 VSSL=0V, VIN=VCC=14V 80 2 0.8 VIN=VCC=15V 95 8.5 VCC=15V, IO=0A 1 VIN=15V, VC/E=0V or Open 1 VCC=15V, VC/E=0V or Open 2 VIN=VCC=15V 0.8 VIN=VCC=14V 95 VC/E=20V 0.5 2 VIN=VCC=14V 0.8 1 4 VIN=14V, VCC=5V, IO=0A, SS1=SS2=0V 8.5 VCC=14V, IO=0V, SS1=SS2=0V 1 4 1.6 10 30 0.1 80 83 250 60 VIN=VCC=10 to 20V, VO=5V, IO=1A 40 1.6 VIN=VCC=15V 4 VIN=15V, VCC=5V, IO=0V, VO12V 8.5 10 40 1.6 VIN=VCC=14V 4 VIN=14V, VCC=5V, IO=0A, VO12V 8.5 VCC=14V, IO=0A 1 VIN=14V, VC/E=0V or Open 1 VIN=14V, VC/E=0V or Open VIN=VCC=15V, VO=5V, IO=0.2 to 1.5A 215 0.996 SPI-8001TW typ. 1.006 max. 1.016 min. 0.996 SPI-8002TW typ. 1.006 0.1 78 81 250 30 285 60 200 30 10 max. 1.016 min. 0.966 SPI-8003TW typ. 1.006 VIN=14V, IO=0.1A 0.1 VIN=14V, IO=0.1A, Ta=30 to +125C 78 VIN= VCC=14V, VO=5V, IO=0.5A, IIN : including ICC 81 VIN=14V, VCC=5V, VO=5V, IO=0.5A, IIN : excluding ICC 400 60 40 VIN=14V, IO=0.1A, COSC=100pF VIN=VCC=9 to 18V, VO=5V, IO=1A VIN=VCC=14V, VO=5V, IO=0.2 to 1.5A max. 1.016
(Ta=25C) Unit
VIN=10V, VO=1V, IO=0.1A VIN=10V, VO=1V, IO=0.1A, Ta=30 to +135C VIN=VCC=15V, VO=5V, IO=0.5A, IIN: including ICC VIN=15V, VO=5V, IO=0.5A, VCC=5V, IIN: excluding ICC VIN=VCC=15V, VO=5V, IO=0.5A
V mV/ C % % kHz mV mV A mA mA
A A
mA mA V V
A
V
*1: Electrical characteristics show the characteristic ratings guaranteed when operating the ICs under the measurement conditions described in the above table. *2: Efficiency is calculated from the following formula.
(%) = VOIO 100 VINIIN *3: Pin 6 and pin 11 are the SS pins. Soft start at power on can be performed with capacitors connected to these pins. The outputs can also be turned ON/OFF with these pins. The outputs are stopped by setting the voltages of these pins to VSSL or lower. SS-pin voltages can be changed with open-collector drive circuits of transistors. When using both the soft-start and ON/OFF functions together, the discharge currents from C4 and C5 flow into the ON/OFF control transistors respectively. Therefore, limit the currents securely to protect the transistors if C4 and C5 capacitances are large. The SS pins are pulled up to the power supply in the ICs, so applying the external voltages are prohibited.
ICs
59
(Unit : mm)
0 to 0.1
2.0+0.2/0.08
10.50.3
0 to 8
2.75MAX
8
2.50.2
0.10
16
Pin Assignment (SPI-8001TW, SPI-8002TW) q AGND o AGND !0 VREF2 w VIN1 e VCC !1 SS2 r SWout1 !2 DGND2 t DGND1 !3 SWout2 y SS1 !4 C/E !5 VIN2 u VREF1 i N.C !6 N.C
(2)
0.90.3
Pin Assignment (SPI-8003TW) q AGND w VIN1 e VCC r SWout1 t DGND1 y SS1 u VREF1 i COSC
o !0 !1 !2 !3 !4 !5 !6
1.270.25
(4.5)
0.4+0.15/0.05
7.50.2
Block Diagram
VIN
+ +
VIN 3 VCC
3 VCC
SPI-8001TW/SPI-8002TW
C1
C6
SPI-8003TW
C1
C4
VC/E
14 C/E
3V
Start
VREF
1V
PReg
OSC RESET
fdown
TSD
UVLO
VC/E
15
C/E
3V
Start
VREF
1V
PReg
OSC RESET
fdown
TSD
UVLO
10 VIN1
2 R7
f down cut
3V
OCP
C9
f down cut
SS1
+ +
3V
OCP
6 R5 C4 7
SS1
+ + +
PWM Logic
Drive
SWOUT1 DGND1 VIN2 4 5 15
6 L1 Di1
+
VO1 C2 R1 R2 C7
R5 7 C5 VREF1
PWM Logic
+
Drive
SWOUT1 DGND1 VIN2 4 5 16
L1 Di1
+
VO1 C2 R1 R2 C7
VREF1
Buffer-Amp
Amp
PWM
Buffer-Amp
Amp
PWM
f down cut
AGND 3V
OCP
f down cut
AGND 3V
OCP
11 R6 C5 10
SS2 VREF2
+ + +
PWM Logic
Buffer-Amp Amp PWM
Drive
SWOUT2 13 12
12 L2 Di2 DGND2
+
SS2 VREF2
+ + +
VO2 C3 C8
R6
11
PWM Logic
Buffer-Amp Amp PWM
Drive
SWOUT2 14 13
L2 Di2
+
VO2 C3 C8
AGND
C6
AGND 1, 9 R3 R4
AGND
DGND2 AGND 1, 9
R3 R4
60
ICs
SPI-8001TW/SPI-8002TW/SPI-8003TW
VIN 3 VCC 2 VIN1 Ch1 VREF1 5 DGND1 SPI-8003TW 16 VIN2 SWout2 14 7 15 C/E SWout1 4 L1
VC/F
VC1 Di1 R1
+
6 R5
SS1
6
C2 C7
SS1
R5
C2 IREF1 R2
C7
IREF1
R2
C4
+
C5
+
C6
C1
C4
C1
VC2 L2 Di2 R3
+
12
C3 C8
SS2
VREF2
Ch2
12
R6
VREF2
11
DGND2 AGND 1, 9
IREF2
13
C8
R4
C5 GND
C6
GND
: 1k : 47 H : SJPB-H6
GND
GND
Diodes Di1, Di2 Be sure to use Schottky-barrier diodes for Di1 and Di2. If other diodes like fast recovery diodes are used, IC may be destroyed because of the reverse voltage generated by the recovery voltage or ON voltage. Choke coils L1, L2 If the winding resistance of the choke coil is too high, the efficiency may drop below the rated value. As the overcurrent protection starting current is about 2.0A, take care concerning heat radiation from the choke coil caused by magnetic saturation due to overload or short-circuited load. Use a closed-magnetic-path coil to prevent interference between the channels SWout1 and SWout2. Capacitors C1, C2, C3 As large ripple currents flow through C1, C2 and C3, use high-frequency and low-impedance capacitors suitable for switching mode power supplies. Especially when the impedance of C2 and C3 are high, the switching waveforms may become abnormal at low temperatures. For C2 and C3, do not use capacitors with extremely low equivalent series resistance (ESR) such as OS capacitors or tantalum capacitors, which may cause abnormal oscillation. Resistors R1, R2, R3, R4 R1, R2, R3 and R4 are resistors for setting output voltages. Set the resistors so that IREF is approx. 1 mA. For example, R1 and R2 can be calculated as shown below.
R1=
(VO1VREF1) (VO1V) VREF1 1 . =1(K) = (), R2= = 1103 IREF1 1103 . IREF1
To create the optimum operating conditions, place the components as close as possible to each other.
Ta-PD Characteristics
3.5
j-a (Copper Laminate Area) 35.8C/W (30.8 cm2)
3.0
PD = VOIO
2.5
52.3C/W (3.34 cm2)
2.0
69.2C/W (0.84 cm2)
VO : VIN : IO : : VF :
Output Voltage Input Voltage Output Current Efficiency (%) D1 Forward Voltage SJPB-H60.45V (IO=1A)
25
50
75
100
Note 1: The efficiency depends on the input voltage and the output current. Therefore, obtain the value from the efficiency graph and substitute the percentage in the formula above. Note 2: Thermal design for D1 must be considered separately.
ICs
61
(Ta=25C)
Applications
Power supplies for notebook PCs and mobile devices Onboard local power supplies OA equipment For stabilization of the secondary-side output voltage of switching power supplies
Electrical Characteristics
Parameter Dynamic Output Voltage Characteristics Temperature Coefficient of Output Voltage Circuit Current (VCC Terminal) Circuit Current Circuit Current (VIN Terminal) Standby Current 1 (VCC Terminal) Standby Current 2 (VIN Terminal) Undervoltage UVLO Operating Voltage 1 (VCC Terminal) Lockout UVLO Operating Voltage 2 (VIN Terminal) On Time On Time Control High Side Drive Low Side Drive Bootstrap Minimum Off Time REF Terminal Voltage REF Terminal Source Current On Resistance (high side) On Resistance (low side) On Resistance (high side) On Resistance (low side) Bootstrap Voltage Current for Current Limit Detection Soft Start Terminal Current EN Low Level Voltage EN High Level Voltage Protection System EN Bias Level Current PWRGD Good Voltage (high side) PWRGD Good Voltage (low side) PWRGD Low Output Voltage PWRGD Terminal Current PWRGD Leakage Current Symbol VO VO/T Iop Iop Istd1 Istd2 Vuvlo1 Vuvlo2 Ton Toff Vref Iref RonHH RonHL RonLH RonLL VH-VLIN Ilim Iss Vcelo Vcehi ICE Vsens Vsens Vpwrgd Ipwrgd Ipwrgd 1.32 0.88 0.4 120 5 0 2.4 4.5 90 5.5 5.5 5.5 5.5 5 100 20 0.8 VCC 5 5.5 110 1.1 3.7 2.5 1.27 0.7 1.2 1.3 100 Ratings min. 1.2% typ. 1.1 0.03 6 1 100 50 4.45 2.9 max. +1.2% Unit V mV/C mA mA
(Ta=25C unless otherwise specified) Conditions VIN=5V, VCC=5V, VSNS connected to VO, IO=0A VIN=5V, VCC=5V, VSNS connected to VO, IO=0A, Ta=0 to 85C VCC=5V, EN=H, FADJ:open VIN=5V, EN=H VCC=5V, EN=L VIN=5V, EN=L VIN=5V VCC=5V VCC=5V, VIN=5V, VO=2.5V VCC=5V VCC=5V VCC=5V VH-VLIN=5V VH-VLIN=5V VCC=5V VCC=5V VCC=5V, VIN=5V VCC=5V VCC=5V VCC=5V VCC=5V, EN=5V VCC=5V VCC=5V VCC=5V, Ipwrgd=120A VCC=5V, Vpwrgd=0.4V Vpwrgd=5V
A A
V V
S S
V
A
V
A A
V V
A
V V V
A A
62
ICs
SI-8511NVS
(Unit : mm)
5.600.1
7.60.2
1.90
3.00
(6.4)
12
11
0.375 TYP
0.15 0.05
+0.1
0.12 M
A 0.4
11
1.150.05
11
11
11
24
13
11
1
S
11
0.100.05
Plastic Mold Package Type Flammability: UL94V-0 Product Mass: Approx. 1.36g
0.500.2
0 to 10
0.08 S
OCP PRE_REG EN H : ON L : OFF EN Vpreg Level Shift VH Latch Buff DRVH VO Synchronous Cont. (Logic) LIN
+
UVLO
POWER_GOOD H : GOOD L : NG
PWRGD
Power Good
+
Logic
VO VSNS
OSC
SS OVP_SL
GND
FSET
14
SS
12
R1 5m R5 10
MOS FET Q1, Q2 Be sure to use logic type MOS FET as Q1 and Q2. If you use a normal power MOS FET type, the ON resistance may not drop to a satisfactory level due to a shortage of VGS. This may deteriorate the efficiency and cause overheating. Diode D1 Be sure to use a Schottky-barrier diode for D1. If other diodes like fast recovery diodes are used, IC may be destroyed because of the reverse voltage generated by the recovery voltage or ON voltage. Choke coil L1 If the winding resistance of the choke coil is too high, the efficiency may drop below the rated value. Take care concerning heat radiation from the choke coil caused by magnetic saturation due to overload or short-circuit load. Capacitor C1, C2 As large ripple currents flow through C1 and C2, use high-frequency and lowimpedance capacitors suitable for switching mode power supplies. Especially when the impedance of C2 is high, the switching waveform may become abnormal at low temperatures. For C2, do not use a capacitor with an extremely low equivalent series resistance (ESR) such as a ceramic capacitor, which may cause an abnormal oscillation. * To create the optimum operating conditions, place the components as close as possible to each other.
24 23 22 21 20 19 Q2 R6 10
Q1 L1 : 10 H VO + D1 SJPJ-L3 C2 : 330 F
C5 : 4.7 F
R13
17 C8 : 220pF 16 15 14 13
R8 : 200k
R11 : 100k
ICs
63
Selection Guide
Linear Regulator ICs (low dropout voltage, built-in overcurrent protection and thermal shutdown circuits) <Single Output>
Surface-Mount Type
Output Current Series Name (A) SI-3000LU SI-3000LSA SI-3000KS SI-3000KD SI-3000LLSL SI-3000ZD 0.25 1.0 1.0 1.0 1.5 3.0 1.8 2.5 Output Voltage (V) 3.3 5.0 9.0 12 Variable (Reference Voltage) (V) 1.0 1.1 1.25 1.28 Dropout Voltage Maximum Input Voltage Package Can Use Low ESR Page
(V)
0.5 1.2 0.6 0.6 0.3 0.6
(V)
18 16 17 35*1 10 10 SOT89-5 SOP8 SOP8 TO263-5 SOP8 TO263-5
Capacitor
*2 66 68 70 72 76 78
*1 For the SI-3012KD and 3033KD: 17 V *2 The SI-3010KD and 3050KD cannot use a low ESR capacitor.
Thru-Hole Type
Output Current Series Name (A) SI-3000KF SI-3000ZF 1.0 3.0 Variable (Reference Voltage) (V) 1.0 1.1 Dropout Voltage (V) 0.5 0.7 Maximum Input Voltage (V) 35 10 TO220F-5 TO220F-5 Package Can Use Low ESR Capacitor 80 82 Page
<Multi Output>
Part Number ch1 ch2 Output Voltage (V) SI-3002KWM 3.3 2.5 Output Current (A) 1.0 1.0 Dropout Voltage (V) 0.6 Maximum Input Voltage (V) 18.0 TO252-5 Package Can Use Low ESR Capacitor 84 Page
64
ICs
Application Note
Heat dissipation and Reliability
The reliability of an IC is highly dependent on its operating temperature. Please be sure to apply silicone grease to the IC and to mount it to the heatsink with a proper mounting torque. Heatsink design should pay particular attention to ensuring sufficient heat dissipation capacity. In addition, please take into account the air convection in operation.
Mounting Torque
SI-3000KF SI-3000ZF
Others
Devices can not be operated in parallel connection aiming for a larger current. Diodes for isolation purpose are provided in between input and ground, and also in between output and ground. They may be broken down if the device is reverse biased. In this case, please clamp the device with low VF diodes to protect them.
Input Ripple
VIN (mean)
VIN (max.)
VIN (min.)
When setting the DC input voltage, please follow the instructions below: Make VIN(min) [ (Output voltage) + (Minimum dropout voltage) ] Make VIN(max) DC input voltage shown in the "Absolute Maximum Ratings"
Thermal Design
The maximum junction temperature Tj(max) given in the absolute maximum ratings is specific to each product type and must be strictly observed. Thus, thermal design must consider the maximum power dissipation PD(max), which varies by the conditions of use, and the maximum ambient temperature Ta(max). To simplify thermal design, Ta-PD characteristic graphs are provided herein. Please observe the following steps for heatsink design: 1. Obtain the maximum ambient temperature Ta(max). 2. Obtain the maximum power dissipation PD(max). 3. Look for the intersection point on the Ta-PD characteristic graph and determine the size of the heatsink. Although the heatsink size is now obtained, in actual applications, 10-to-20% derating factor is generally introduced. Moreover, the heat dissipation capacity of a heatsink highly depends on how it is mounted. Thus, it is recommended to measure the heatsink and case temperature in the actual operating environment. Please refer to the Ta-PD characteristic graphs for respective product types.
ICs
65
(Ta=25C)
j-a*1
*1: When mounted on glass-epoxy board 40 40 mm (copper laminate area 2%). *2: Thermal protection circuits may operate if the junction temperature exceeds 135C.
Applications
Auxiliary power supplies for PC Battery-driven electronic equipment
Unit V mA C
0 20
*1: VIN (max) and IO (max) are restricted by the relation PD = (VIN - VO) IO. Calculate these values referring to the reference data on page 67. *2: Refer to the Dropout Voltage parameter. *3: For the SI-3012LU, set the input voltage to Vin 2.4 V, and secure the minimum voltage as explained in "Setting DC Input Voltage" section in Linear Regulator Application Note.
Electrical Characteristics
Ratings Parameter Symbol min. Reference Voltage VADJ Conditions VDIF Dropout Voltage Conditions Conditions VLINE Line Regulation Conditions VLOAD Load Regulation Conditions Temperature Coefficient of Reference Voltage Ripple Rejection Conditions Quiescent Circuit Current Circuit Current at Output OFF Overcurrent Protection Starting Current*1 Control Voltage (Output VC Terminal ON)*2 Control Voltage (Output OFF)*2 Control Current (Output ON) Control Current (Output OFF) Iq Conditions Iq(OFF) Conditions IS1 Conditions VC, IH VC, IL IC, IH Conditions IC, IL Conditions VC=2V 0 VC=0V 2.0 260 VIN=VO +1V VIN=VO+1V, VC=0V VIN=VO+1V, IO =0mA VC=2V, R2=100k VO/Ta Conditions RREJ VIN=VO +1V, IO=1 to 250mA( V O=3.3V) 0.3 Tj=0 to 100C 55 VIN=VO +1V , f=100 to 120HZ( VO=3.3V) VIN=VO+1 to VO+5V, IO=10mA( VO=3.3V) IO=100mA(VO =3.3V) 1.210 SI-3012LU(Variable) typ. 1.250 VIN=VO+1V, IO =10mA
(Ta=25C, VC=2V, unless otherwise specified) Unit max. 1.290 0.3 0.5 IO=250mA(VO =3.3V) 10 mV 20 mV V V
mV/ C
dB 150
A
1
A
mA V
0.8 40 5
A A
*1: Is1 is specified at the 5% drop point of output voltage VO on the condition that VIN = 3.3 V, and IO = 10 mA. *2: Output is OFF when the output control terminal (VC terminal) is open. Each input level is equivalent to LS-TTL level. Therefore, the device can be driven directly by LS-TTLs.
66
ICs
SI-3000LU Series
(Unit : mm)
2.50.05
4.30.05
( 1
.0
5 0.0 )
Pin Assignment q ADJ w GND e VC r VIN t VO Plastic Mold Package Type Flammability: UL94V-0 Product Mass: Approx. 0.05g
0.40
4.20.05
4.20.05
1.50.05
1.50.05
Block Diagram
SI-3012LU
VIN 4 5 VO
0.40.05
1.50.05
0.900.1
4.70.05
0.900.1
VC 3 TSD
+
1 ADJ
2 GND
REF
+
VIN
CO: Output capacitor (10 F or larger) For SI-3000LU series, Co has to be a low ESR capacitor such as a ceramic capacitor. CIN: Input capacitor (10 F approx.) Setting of SI-3012LU output voltage (recommended voltage: 1.5 V to 15 V) R1 and R2: Resistors for output setting The output voltage can be set by connecting R1 and R2 as shown in the diagram on the left. R2: 100 k is recommended R1=(VOVADJ)/(VADJ/R2)
Reference Data
Copper Laminate Area vs Power Dissipation Tj=100C PCB size 4040
1 0.9
Ta=25C Ta=40C Ta=60C Ta=85C
A monolithic ICs mounts an inner frame stage that is connected to the GND pin (pin 2). Therefore, enlarging the copper laminate area connected to the GND pin improves heat radiation effect. Obtaining the junction temperature Measure the temperature TC at the lead part of the GND pin (pin 2) with a thermocouple, etc. Then, substitute this value in the following formula to obtain the junction temperature. T j =PD jc+Tc ( jc=5 C/W)
100
1000
ICs
67
SI-3000LSA Series
Features
Compact surface-mount package (SOP8) Output current: 1 A
Low circuit current at output OFF: Iq(OFF) 1 A (VC = 0 V) Low dropout voltage: VDIF0.8 V (at IO = 1 A) VDIF 1.2 V (IO = 1 A) for SI-3018LSA 4 types of output voltages (1.8 V, 2.5 V, 3.3 V, 5.0 V) available Output ON/OFF control terminal voltage compatible with LS-TTL Built-in foldback-type-overcurrent and thermal protection circuits
j-L j-a *2
*1: When mounted on glass-epoxy board 56.5 56.5 mm (copper laminate area 100%). *2: When mounted on glass-epoxy board 40 40 mm (copper laminate area 100%). *3: Thermal protection circuits may be activated if the junction temperature exceeds 135C.
Applications
Auxiliary power supplies for PC Battery-driven electronic equipment
SI-3033LSA
*2
SI-3050LSA
*2
Unit V A C C
to 3.5*1 0 to 1
to 5.2*1
to 8.0
20 to +125 30 to +85
*1: VIN (max) and IO (max) are restricted by the relation PD = (VIN VO) IO. Please calculate these values referring to the reference data on page 69. *2: Refer to the Dropout Voltage parameter.
Electrical Characteristics
Ratings Parameter Symbol min. Output Voltage VO Conditions VDIF Dropout Voltage Conditions Conditions Line Regulation Load Regulation Temperature Coefficient of Output Voltage Ripple Rejection Quiescent Circuit Current Circuit Current at Output OFF Overcurrent Protection Starting Current*1,3 Control Voltage (Output VC Terminal ON)*2 Control Voltage (Output OFF)*2 Control Current (Output ON) Control Current (Output OFF) VLINE Conditions VOLOAD Conditions VO/Ta Conditions RREJ Conditions Iq Conditions Iq(OFF) Conditions IS1 Conditions VC, IH VC, IL IC, IH Conditions IC, IL Conditions 0 5 0 5 VC=0V 40 2.0 0.8 80 40 1.2 VIN=3.3V 2.0 0.8 80 VC=2V 0 5 40 2 10 0.3 VIN=3.3V, IO=5mA, Tj=0 to 100C 60 VIN=3.3V, f=100 to 120HZ 1.7 VIN=3.3V, IO=0A 1 VIN=3.3V, IO=0A, VC=0V 1.2 VIN=3.3V 2.0 0.8 80 2.5 10 20 2 10 0.3 VIN=3.3V, IO=5mA, Tj=0 to 100C 57 VIN=3.3V, f=100 to 120HZ 1.7 VIN=3.3V, IO=0A 1 VIN=3.3V, IO=0A, VC=0V 1.2 VIN=5V 2.5 10 20 VIN=3.1 to 3.5V, IO=0.3A VIN=3.3V, IO=0 to 1A VIN=3.1 to 3.5V, IO=0.3A VIN=3.3V, IO=0 to 1A 1.764 SI-3018LSA typ. 1.800 0.6 1.2 IO0.5A 0.8 IO1A 3 10 0.3 VIN=5V, IO=5mA, Tj=0 to 100C 55 VIN=5V, f=100 to 120HZ 1.7 VIN=5V, IO=0A 1 VIN=5V, IO=0A, VC=0V 2.5 10 20 max. 1.836 min. 2.450 SI-3025LSA typ. 2.500 max. 2.550 0.4 IO0.5A 0.8 min. 3.234 SI-3033LSA typ. 3.300 max. 3.366 0.4
(Ta=25C, VC=2V, unless otherwise specified) SI-3050LSA min. 4.90 typ. 5.00 VIN=6V, IO=0.5A 0.4 IO0.5A 0.8 3 10 0.5 VIN=6V, IO=5mA, Tj=0 to 100C 55 VIN=6V, f=100 to 120HZ 1.7 VIN=6V, IO=0A 1 VIN=6V, IO=0A, VC=0V 1.2 VIN=6V 2.0 0.8 40 0 80 5 2.5 15 30 V max. 5.10 V Unit
VIN=3.3V, IO=0.5A
VIN=3.3V, IO=0.5A
VIN=5V, IO=0.5A
mV mV mV/ C dB mA
A
A V
A A
*1: Is1 is specified at the 5% drop point of output voltage VO on the condition that VIN = 3.3 V (5 V for SI-3033LSA), and IO = 0.5 A. *2: Output is OFF when the output control terminal VC is open. Each input level is equivalent to LS-TTL level. Therefore, the device can be driven directly by LS-TTLs. *3: These products cannot be used in the following applications. Because these applications require a certain current at start-up and so the built-in foldback-type overcurrent protection may cause errors during start-up stage. (1) Constant current load (2) Positive and negative power supply (3) Series-connected power supply (4) VO adjustment by raising ground voltage
68
ICs
SI-3000LSA Series
(Unit : mm)
0.995max.
1.550.15 1.50.1
to
10
1.27
Pin Assignment q VIN w NC (Leave open) e VIN r VC t GND y GND u VO i VO Plastic Mold Package Type Flammability: UL94V-0 Product Mass: Approx. 0.1g
Block Diagram
VIN 1 8 VO
0.050.05
4.40.2
NC 2
+
7 VO
VIN 3
TSD
6.20.3
GND
VC 4
GND
Reference Data
PCB Copper Laminate Area vs. Junction to Ambient Air Thermal Resistance Allowable Output Current (vs. VIN-VOUT Voltage Difference) VIN-IO max
1.2
1.0
Load
CO: Output capacitor (22 F or larger) CIN: Input capacitor (10 F) This capacitor is required in the case of an inductive input line or long wiring. Tantalum capacitors are recommended for CIN and CO, particularly at low temperatures. * Leave pin 2 open.
0.8
j-a (C/W)
j-a=100C/W
0.6
The inner frame stage, on which the PTr is mounted, is directly connected to the VOUT pin. Therefore, enlarging the copper laminate area around the VOUT pin is really effective for a heat radiation.
0.4
Ta=25C Ta=85C
ICs
69
(Ta=25C)
j-a j-L
*1: VIN (max) and IO (max) are restricted by the relation PD = (VIN - VO) IO. Please calculate these values referring to the Copper laminate area vs. Power dissipation data as shown hereinafter. *2: When mounted on a glass epoxy board of 1600 mm2 (copper laminate area 2%).
Applications
Local power supplies Battery-driven electronic equipment
Electrical Characteristics
Ratings Parameter Input Voltage Output Voltage (Reference voltage VADJ for SI-3012KS) Symbol VIN VO (VADJ) Conditions VDIF Dropout Voltage Conditions Conditions Line Regulation Load Regulation Quiescent Circuit Current Circuit Current at Output OFF Temperature Coefficient of Output Voltage Ripple Rejection Overcurrent Protection Starting Current*2 Control Voltage (Output ON)*3 Control Voltage (Output OFF) VC Terminal Control Current (Output ON) Control Current (Output OFF) VOLINE Conditions VOLOAD Conditions Iq Conditions Iq (OFF) Conditions VO/Ta Conditions RREJ Conditions IS1 Conditions VC, IH VC, IL IC, IH Conditions IC, IL Conditions 5 0 5 2.0 0.8 40 VC=2V 0 VC=0V 5 1.2 VIN=3.3V (VO=2.5V) 2.0 0.8 40 VIN=3.3V, VC=0V 0.3 Tj=0 to 100C (VO=2.5V) 55 VIN =3.3V, f=100 to 120HZ (VO=2.5V) 1.2 VIN=3.3V 2.0 IO=0.5A (VO=2.5V) 0.6 IO=1A (VO=2.5V) 10 VIN=3.3 to 8V, IO=10mA (VO=2.5V) 40 VIN=3.3V, IO=0 to 1A (VO=2.5V) 350 VIN=3.3V, IO=0A, VC=2V, R2=24k 1 VIN=3.3V, VC=0V 0.3 Tj=0 to 100C 55 VIN=3.3V, f=100 to 120HZ 1.2 VIN=3.3V, IO=0A, VC=2V 1 VIN=3.3V, IO=0 to 1A 350 VIN=3.3 to 8V, IO=10mA 40 IO=1A 10 SI-3012KS (variable type) min. 2.4 1.24 1.28 VIN=3.3V, IO=10mA 0.3 IO=0.5A 0.6 1.32 typ. max. min.
*1
Unit V 3.366 V
2.45
3.234
A A
mV/ C dB A V
A A
*1: Refer to the Dropout Voltage parameter. *2: The Is1 is specified at the 5% drop point of output voltage VO on the condition that VIN = VO + 1 V, and IO = 10 mA. *3: Output is OFF when the output control terminal VC is open. Each input level is equivalent to LS-TTL level. Therefore, the device can be driven directly by LS-TTLs.
70
ICs
SI-3000KS Series
(Unit : mm)
0.15+0.1 0.05
1.27
0.40.1
0.995max.
to
10
1.27
Pin Assignment q VC w VIN e VO r Sence (ADJ for SI-3012KS) t GND y GND u GND i GND Plastic Mold Package Type Flammability: UL 94V-0 Product Mass: Approx. 0.1 g
Block Diagram
SI-3012KS
VIN 2 3 VO
SI-3025KS, SI-3033KS
VIN 2 3 VO
4
VC 1 +
VC 1 +
SI-3025KS, SI-3033KS
VIN 2 VO 3 CO
R1
CO
VC GND ADJ 1 4 5 to 8
Load
CIN
sense VC GND 4 1 5 to 8
Load
R2
R2
R1, R2: Output voltage setting resistors The output voltage can be set by connecting R1 and R2 as shown above. The recommended value of R2 is 24 k .
CIN: Input capacitor (22 F or larger) CO: Output capacitor (22 F or larger) For SI-3000KS series, Co has to be a low ESR capacitor. When using the electrolytic capacitor, the SI-3000KS series may oscillate at a low temperature.
R1=(VOVADJ)(VADJ/R2)
Reference Data
Copper Laminate Area vs. Thermal Resistance
140 Area of PC board : 4040mm
1.2
120
Power dissipation PD (W)
Ta=50C Ta=80C
0.8
100
Obtaining the junction temperature Measure the temperature TL at the lead part of the GND pin (pin 7) with a thermocouple, etc. Then, substitute this value in the following formula to obtain the junction temperature.
0.6 0.4
Tj=PD jL + TL
( jL = 22C/W)
80
60
0.2
40 10
1000
0 10
1000
ICs
71
SI-3000KD Series
Features
Compact surface-mount package (TO263-5) Output current: 1.0A Low dropout voltage: VDIF 0.6V (at IO = 1.0A) Low circuit current consumption: Iq 350 A (600 A for SI-3010KD, SI-3050KD) Low circuit current at output OFF: Iq (OFF) 1 A Built-in overcurrent, thermal protection circuits Compatible with low ESR capacitors (SI-3012KD and SI-3033KD)
j-a j-c
*1: A built-in input-overvoltage-protection circuit shuts down the output voltage at the Input Overvoltage Shutdown Voltage of the electrical characteristics. *2: When mounted on glass-epoxy board of 1600mm2 (copper laminate area 100%).
Applications
Secondary stabilized power supply (local power supply)
Electrical Characteristics 1 (Low Input Voltage type compatible with low ESR output capacitor)
Ratings
Parameter
Input Voltage Output Voltage (Reference Voltage for SI-3012KD) Line Regulation Load Regulation
Symbol min. VIN VO (VADJ) Conditions VOLINE Conditions VOLOAD Conditions VDIF Conditions Conditions 2.4*3 1.24
SI-3012KD (Variable type) typ. 1.28 VIN=3.3V, IO=10mA 15 VIN=3.3 to 8V, IO=10mA (VO=2.5V) 40 VIN=3.3V, IO=0 to 1A (VO=2.5V) 0.4 IO=0.5A (VO=2.5V) 0.6 IO=1A (VO=2.5V) 350 VIN=3.3V, IO=0A, VC=2V, R2=2.4k 1 VIN=3.3V, VC=0V 0.3 Tj=0 to 100C (VO=2.5V) 55 VIN=3.3V, f=100 to 120HZ, IO=0.1A (VO=2.5V) 1.1 VIN=3.3V 2 0.8 40 VC=2V 5 0 VC=0V 5 2 1.1 max.
*4
SI-3033KD min.
*3
V V mV mV
1.32
3.234
3.366 15
VIN=5 to 10V, IO=10mA 50 VIN=5V, IO=0 to 1A 0.4 IO=0.5A 0.6 IO=1A 350 VIN=5V, IO=0A,VC=2V 1 VIN=5V, VC=0V 0.3 Tj=0 to 100C 55 VIN=5V, f=100 to 120HZ, IO=0.1A VIN=5V 0.8 40 VC=2V 0 VC=0V
Dropout Voltage
Quiescent Circuit Current Circuit Current at Output OFF Temperature Coefficient of Output Voltage Ripple Rejection Overcurrent Protection Starting Current*1 Control Voltage (Output VC Terminal ON)*2 Control Voltage (Output OFF) Control Current (Output ON) Control Current (Output OFF)
Iq Conditions Iq (OFF) Conditions VO/Ta Conditions RREJ Conditions IS1 Conditions VC, IH VC, IL IC, IH Conditions IC, IL Conditions
A A
mV/ C dB A V
A A
*1: IS1 is specified at the 5% drop point of output voltage VO under the condition of Output Voltage parameter. *2: Output is OFF when the output control terminal (VC terminal) is open. Each input level is equivalent to LS-TTL level. Therefore, the device can be driven directly by LS-TTLs. *3: Refer to the Dropout Voltage parameter. *4: VIN (max) and IO (max) are restricted by the relation PD = (VIN - VO) IO. Please calculate these values referring to the Copper laminate area vs. Power dissipation data.
72
ICs
SI-3000KD Series
Parameter
Input Voltage Output Voltage (Reference Voltage VADJ for SI-3010KD) Line Regulation
Symbol min. VIN VO (VADJ) Conditions VOLINE Conditions VOLOAD 2.4*1 0.98
SI-3010KD (Variable type) typ. 1.00 VIN=7V, IO=10mA 30 VIN=6 to 11V, IO=10mA (VO=5V) 75 VIN=7V, IO=0 to 1A (VO=5V) 0.3 IO=0.5A (VO=5V) 0.6 IO=1A (VO=5V) 600 VIN=7V, IO=0A, VC=2V R2=10k 1 VIN=7V, VC=0V 0.5 Tj=0 to 100C (VO=5V) 75 VIN=7V, f=100 to 120Hz, IO=0.1A (VO=5V) 1.1 VIN=7V 2.0 0.8 40 VC=2V 5 33 IO=10mA 0 VC=0V 26 5 2.0 1.1 max. 27*5 1.02 min.
*1
SI-3050KD typ. 5.00 VIN=7V, IO=10mA 30 VIN=6 to 11V, IO=10mA 75 VIN=7V, IO=0 to 1A 0.3 IO=0.5A 0.6 IO=1A 600 VIN=7V, IO=0A, VC=2V 1 VIN=7V, VC=0V 0.5 Tj=0 to 100C 75 VIN=7V, f=100 to 120Hz, IO=0.1A VIN=7V 0.8 40 VC=2V 0 VC=0V IO=10mA max. 15*5 5.10
Unit
V V
4.90
mV
Load Regulation
Conditions VDIF
mV
Dropout Voltage
Conditions Conditions Iq
A A
mV/ C dB
Circuit Current at Output OFF Temperature Coefficient of Output Voltage Ripple Rejection Overcurrent Protection Starting Current*2
*4
Conditions IS1 Conditions ON)*3 VC, IH VC, IL IC, IH Conditions IC, IL Conditions VOVP Conditions
A V
Control Voltage (Output OFF)*3 Control Current (Output ON) Control Current (Output OFF) Input Overvoltage Shutdown Voltage
A A
V
Refer to the Dropout Voltage parameter. Is1 is specified at the 5% drop point of output voltage VO under the condition of Output Voltage parameter. Output is OFF when the output control terminal (VC terminal) is open. Each input level is equivalent to LS-TTL level. Therefore, the device can be driven directly by LS-TTLs. SI-3010KD, SI-3050KD, cannot be used in the following applications because the built-in foldback-type overcurrent protection may cause errors during start-up stage. (1) Constant current load (2) Positive and negative power supply (3) Series-connected power supply (4) VO adjustment by raising ground voltage *5: VIN (max) and IO (max) are restricted by the relation PD = (VIN - VO) IO. Please calculate these values referring to the Copper laminate area vs. Power dissipation data as shown hereinafter.
(unit : mm)
10.0
0.2
1.2
(15)
(1.75)
(6.8)
0.2
9.2
0.3
15.3
(3)
0.1
0.10 (3)
0.15
2.4 (R0.3)
0.3
0.2
0.2
2.0
15.30
0.3
(0.75)
4.9
0.88
0.10
(R0.3)
2.54
0 to 6 (0.5)
0.1
4.9
0.2
9.2
0.2
1.5 Dp:
0.2
(3)
(2R0.45)
Pin Assignment q VC w VIN e GND (Common to the rear side of product) r VO t Sense (ADJ for SI-3010KD/3012KD) Plastic Mold Package Type Flammability: UL94V-0 Product Mass: Approx. 1.48g
(1.7
0.25
) 1 2 3 4 9.9
0.2
0.1
(4.6)
(1.7
0.25
(3) 2-R0.3
10.0
0.02
ICs
73
Block Diagram
SI-3010KD/SI-3012KD
VIN 2 4 VO
SI-3033KD/SI-3050KD
VIN 2 4 Vo
5 VC 1 +
5 ADJ TSD
VC 1 +
Sense TSD
REF 3 GND
REF 3 GND
D1*2
*1
D1*2 R3
*3 *1
VIN 2
+
VO 4
+
VIN 2
+
VO 4
R1
+
CIN
sense VC GND 5 1 3
CO
Load
CIN
VC GND ADJ 1 5 3
CO
Load
R2
CIN: Input capacitor (22 F or larger) CO: Output capacitor *1: SI-3012KD/3033KD (22 F or larger) Co has to be a low ESR capacitor such as a ceramic capacitor. When using the electrolytic capacitor, oscillation may occur at a low temperature. SI-3010KD/3050KD/ (47 F or larger) If a low ESR capacitor is used, oscillation may occur. *2: D1: Reverse bias protection diode This diode is required for protection against reverse biasing between the input and output. (Sanken SJPL-H2 is recommended.) This diode is not required at VO 3.3V.
R1, R2: Output voltage setting resistors The output voltage can be set by connecting R1 and R2 as shown above. The recommended value for R2 is 10 (24k for SI-3012KD).
R1=(VOVADJ)(VADJ/R2)
*3: For SI-3010KD, insert R3 in case of setting VO to VO 1.5V. The recommended value for R3 is 10k.
Reference Data
Copper Laminate Area (on Glass-Epoxy Board) vs. Thermal Resistance (from Junction to Ambient Temperature) (Typical Value)
55
Junction to Ambient Temperature Thermal Resistance j-a (C/W)
A higher heat radiation effect can be achieved by enlarging the copper laminate area connected to the inner frame to which a monolithic ICs is mounted. Obtaining the junction temperature Measure the case temperature TC with a thermocouple, etc. Then, substitute this value in the following formula to obtain the junction temperature.
74
ICs
ICs
75
(Ta=25C)
V V V A W
C C C C/W C/W
(j-L) (j-a)*1
*1: When mounted on glass-epoxy board of 40 40mm (copper laminate area 100%).
Applications
On-board local power supply For stabilization of the secondary-side output voltage of switching power supplies
VIN VB IO Top
Unit
V V A C
*1: VIN (max) and IO (max) are restricted by the relation PD = (VIN - VO) IO.
Electrical Characteristics
Parameter Symbol min. Reference Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Circuit Current Circuit Current at Output OFF Temperature Coefficient of Output Voltage Overcurrent Protection Starting Current*1 Control Voltage (Output VC Terminal ON)*2 Control Voltage (Output OFF) Control Current (Output ON) Control Current (Output OFF) VADJ Conditions VOLINE Conditions VOLOAD Conditions VDIF Conditions Iq Conditions Iq (OFF) Conditions VO/Ta Conditions IS1 Conditions VC, IH VC, IL IC, IH Conditions IC, IL Conditions 2 1.6 0.980 typ.
(Ta=25C, VC=2V, VIN=1.8V, VB=3.3V, VO=1.5V, unless otherwise specified) Ratings SI-3010LLSL max. 1.020 10 VIN=1.7 to 2.5V, IO=10mA 30 VIN=1.8V, IO=0 to 1.5A 0.3 IO=1.0A 500 IO=0A, R2=10k 1 VC=0V 0.2 Tj=0 to 100C VIN=1.8V, VB=3.3V 0.8 50 VC=2.7V 10 VC=0.4V 800 V mV mV V 1.000 IO=10mA Unit
A A
mV/ C A V V
A A
*1: IS1 is specified at the 5% drop point of output voltage VO on the condition that VIN = overcurrent protection starting current, IO = 10 mA. *2: Output is OFF when the output control terminal (VC terminal) is open. Each input level is equivalent to LS-TTL level. Therefore, the device can be driven directly by LS-TTLs.
76
ICs
SI-3000LLSL Series
(unit : mm)
Pin Assignment q VO w ADJ e VB r VC t GND y GND u VIN i VIN Plastic Mold Package Type Flammability: UL94V-0 Product Mass: Approx. 0.1g
1.27 0.995max.
6.20.3
VIN
+
7 8
R1
CIN VB 3 REF
+
CO
CB 4 VC
ON/OFF +
R1= (VOVADJ) / (VADJ/R2) CSS:Soft start capacitor The rising time of the output voltage can be set by connecting CSS between VOUT and ADJ.
Reference Data
Copper Laminate Area - Power Dissipation
1.2 Ta=25C 1
Pd (W)
0.8 0.6
Ta=50C
1000
ICs
77
(Ta=25C)
Applications
Secondary stabilized power supply (local power supply)
j-a j-c
Unit V A C C V
Remarks
to 6*1
*1: VIN (max) and IO (max) are restricted by the relation PD = (VIN - VO) IO. *2: Set the input voltage to 2.4V or higher when setting the output voltage to 2.0V or lower (SI-3011ZD). *3: When mounted on glass-epoxy board of 40 40mm (copper laminate area 100%).
Electrical Characteristics
Ratings Parameter Output Voltage (Reference Voltage VADJ for SI-3011ZD) Line Regulation Load Regulation Dropout Voltage Quiescent Circuit Current Circuit Current at Output OFF Temperature Coefficient of Output Voltage Ripple Rejection Overcurrent Protection Starting Current*2
*4
(Ta=25C, VC=2V, unless otherwise specified) SI-3011ZD (Variable type) min. typ. 1.100 VIN=VO+1V, IO=10mA 10 VIN=3.3 to 5V, IO=10mA (VO=2.5V) 40 VIN=3.3V, IO=0 to 3A (VO=2.5V) 0.6 IO=3A (VO=2.5V) 1 VIN=VO+1V, IO=0A, VC=2V 1 VIN=VO+1V, VC=0V 0.3 Tj=0 to 100C 60 VIN=VO+1V, f=100 to 120HZ, IO=0.1A 3.2 VIN=VO+1V 2 0.8 100 VC=2.7V 5 0 VC=0V 5 VC=2.7V 0 VC=0V 2 0.8 100 3.2 VIN=5V VIN=5V, VC=0V 0.3 Tj=0 to 100C 60 VIN=5V, f=100 to 120HZ, IO=0.1A 1.5 IO=3A 1 VIN=5V, IO=0A, VC=2V 1 1.5 VIN=5V, IO=0 to 3A 0.6 VIN=4.5 to 5.5V, IO=10mA 40 max. 1.122 min. 3.234 1.078 SI-3033ZD typ. 3.300 VIN=5V, IO=10mA 10 max. 3.366 V mV mV V mA Unit
Symbol VO (VADJ) Conditions VOLINE Conditions VOLOAD Conditions VDIF Conditions Iq Conditions Iq (OFF) Conditions VO/Ta Conditions RREJ Conditions IS1 Conditions VC, IH VC, IL IC, IH Conditions IC, IL Conditions
A
mV/ C dB A V
Control Voltage (Output ON)*3 Control Voltage (Output OFF)*3 VC Control Current(Output ON) Terminal Control Current(Output OFF)
A A
*1: Set the input voltage to 2.4V or higher when setting the output voltage to 2.0V or lower. *2: IS1 is specified at the 5% drop point of output voltage VO under the condition of Output Voltage parameter. *3: Output is OFF when the output control terminal (VC terminal) is open. Each input level is equivalent to LS-TTL level. Therefore, the device can be driven directly by LS-TTLs. *4: These products cannot be used for the following applications because the built-in foldback-type overcurrent protection may cause errors during start-up stage. (1) Constant current load (2) Positive and negative power supply (3) Series-connected power supply (4) VO adjustment by raising ground voltage
78
ICs
SI-3000ZD Series
(Unit : mm)
(0.40)
1.2
(15)
0.2
(4.6)
(1.75)
(6.8)
0.2
9.2
0.3
9.2
0.2
1.5 Dp:
0.2
(3)
(2R0.45)
(3)
0.1
0.10 (3)
0.15
2.4 (R0.3)
0.3
0.2
0.88
0.10
(R0.3)
0~6
0.1
(0.5) (1.7
0.25
) 1 2 3 4 9.9
0.2
0.1
(1.7
0.25
Pin Assignment q VC w VIN e GND (Common to the rear side of product) r VO t Sense (ADJ for SI-3011ZD) Plastic Mold Package Type Flammability: UL94V-0 Product Mass: Approx. 1.48g
15.3
0.2
2.0
15.30
0.3
(0.75)
4.9
10.0
0.02
Block Diagram
SI-3011ZD
VIN
+
2.54
4.9
0.2
VO
R3
*
CIN REF
+ +
R1
+
5 ADJ CO R2
CIN: Input capacitor (Approx. 10F) CO: Output capacitor (47F or larger) The output voltage may oscillate if a low ESR type capacitor (such as a ceramic capacitor) is used for the output capacitor in the SI-3000ZD Series.
VC
ON/ OFF 1
SI-3033ZD
VIN
+
CIN REF
+ +
TSD
OCP
AMP1
CO
VC
ON/ OFF 1
3 GND
Reference Data
Copper Laminate Area (on Glass-Epoxy Board) vs. Thermal Resistance (from Junction to Ambient Temperature) (Typical Value)
55
Junction to Ambient Temperature Thermal Resistance j-a (C/W)
200
400
600
800
1000
1200
1400
1600
1800
Drive
GND
4 5
VO
SENSE
R1, R2: Output voltage setting resistors The output voltage can be set by connecting R1 and R2 as shown at left. The recommended value for R2 is 10k or 11k.
R1= (VOVADJ) / (VADJ/R2) *: Insert R3 in case of setting VO to VO 1.8V. The recommended value for R3 is 10k.
A higher heat radiation effect can be achieved by enlarging the copper laminate area connected to the inner frame to which a monolithic IC is mounted. Obtaining the junction temperature Measure GND terminal temperature TC with a thermocouple, etc. Then substitute this value in the following formula to obtain the junction temperature.
Tj=PD jC+TC
PD= (VINVO)IOUT
ICs
79
(Ta=25C)
j-c j-a
Applications
Secondary stabilized power supply (local power supply)
*1: A built-in input-overvoltage-protection circuit shuts down the output voltage at the Input Overvoltage Shutdown Voltage of the electrical characteristics.
*1: VIN (max) and IO (max) are restricted by the relationship PD (max) = (VIN - VO) IO = 16.6W. *2: Refer to the Dropout Voltage parameter.
Electrical Characteristics
Ratings Parameter Symbol min. VADJ Reference Voltage Conditions VOLINE Line Regulation Conditions VOLOAD Load Regulation Conditions VDIF Dropout Voltage Conditions Conditions Quiescent Circuit Current Circuit Current at Output OFF Temperature Coefficient of Output Voltage Iq Conditions Iq (OFF) Conditions VO/Ta Conditions RREJ Ripple Rejection Overcurrent Protection Starting Current*3 Control Voltage (Output ON)*4 Control Voltage (Output OFF) Control Current (Output ON) Control Current (Output OFF) Input Overvoltage Shutdown Voltage Conditions IS1 Conditions VC, IH Conditions VC, IL Conditions IC, IH Conditions IC, IL Conditions VOVP Conditions 33 IO=0.01A 5 VIN=7V, VC=2V 0 VIN=7V, VC=0V VIN=7V 40 2 VIN=7V 0.8 1.1 VIN=7V, VC=2V VIN=7V, VC=0V 0.5 VIN=7V, IO=0.01A, VC=2V, Tj=0 to 100C, VO=2.5V 75 VIN=7V, IO=0.1A, VC=2V, f=100 to 120Hz, VO=5V dB mV/ C VIN=7V, IO=0A, VC=2V 1 IO=0.5A, VC=2V, VO=5V 0.5 IO=1.0A, VC=2V, VO=5V 600 VIN=7V, IO=0 to 1A, VC=2V, VO=5A 0.3 V VIN=6 to 15V, IO=0.01A, VC=2V, VO=5A 75 mV 0.98 SI-3010KF typ. 1.00 VIN=7V, IO=0.01A, VC=2V, VO=5A 30 mV max. 1.02 V Unit
A A
A V V
VC Terminal
A A
V
*3: IS1 is specified at the 5% drop point of output voltage VO on the condition that VIN = overcurrent protection starting current, IO = 10 mA. *4: Output is OFF when the output control terminal VC is open. Each input level is equivalent to LS-TTL level. Therefore, the device can be driven directly by LS-TTLs. *5: SI-3000KFE cannot be used in the following applications because the built-in foldback-type overcurrent protection may cause errors during start-up stage. (1) Constant current load (2) Positive and negative power supply (3) Series-connected power supply (4) VO adjustment by raising ground voltage
80
ICs
SI-3000KF Series
Block Diagram
SI-3010KF
Ta-PD Characteristics
20 With Infinite Heatsink Silicone Grease: G746 (Shin-Etsu Chemical) Heatsink: Aluminum
VIN 2
4 VOUT
VC 1 TSD
+
5 ADJ
3 GND
REF
D1*1
VIN 2
+
VO 4
R1
+
CIN
VC GND ADJ 1 5 3
*2
CO
Load
R2
R3
CIN: Input capacitor (22F or larger) CO: Output capacitor (47F or larger) If a low ESR capacitor (such as a ceramic capacitor) is used for the output capacitor, oscillation may occur. *1. D1: Reverse bias protection diode This diode is required for protection against reverse biasing between the input and output. (Sanken RU2Z is recommended.)
R1, R2: Output voltage setting resistors The output voltage can be adjusted by connecting R1 and R2 as shown above. The recommended value for R2 is 10k.
R1=(VOVADJ)(VADJ/R2)
*2: Insert R3 in case of setting VO to VO 1.5V. The recommended value for R3 is 10k.
(Unit : mm)
0.5
10.0
0.2
16.90.3
3.20.2
2.60.1
(2.0)
0.95
0.15 +0.2
Pin Assignment q Vc w VIN e GND r Vout t ADJ Plastic Mold Package Type Flammability: UL 94V-0 Product Mass: Approx. 2.3 g
0.45 0.1
+0.2
3.90.7
(4.3) 8.20.7
1 2 3 4 5
4.60.6
(4.6)
(17.9)
ICs
81
Applications
Secondary stabilized power supply (local power supply)
j-c j-a
C/W C/W
Unit V A C C V
to 6*1
*1: VIN (max) and IO (max) are restricted by the relationship PD = (VIN - VO) IO. *2: Set the input voltage to 2.4V or higher when setting the output voltage to 2.0V or lower.
Electrical Characteristics
Parameter Symbol min. Reference Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Circuit Current Circuit Current at Output OFF Temperature Coefficient of Output Voltage Ripple Rejection Overcurrent Protection Starting Current*2
*4
VADJ Conditions VOLINE Conditions VOLOAD Conditions VDIF Conditions Iq Conditions Iq (OFF) Conditions VO/Ta Conditions RREJ Conditions IS1 Conditions VC, IH VC, IL IC, IH Conditions IC, IL Conditions
A
mV/ C dB A V
ON)*3
Control Voltage (Output OFF)*3 VC Control Current(Output ON) Terminal Control Current(Output OFF)
A A
*1: Set the input voltage to 2.4V or higher when setting the output voltage to 2.0V or lower. *2: IS1 is specified at the 5% drop point of output voltage VO under the Output Voltage parameter conditions. *3: Output is OFF when the output control terminal VC is open. Each input level is equivalent to LS-TTL level. Therefore, the device can be driven directly by LS-TTLs. *4: These products cannot be used in the following applications because the built-in foldback-type overcurrent protection may cause errors during start-up stage. (1) Constant current load (2) Positive and negative power supply (3) Series-connected power supply (4) VO adjustment by raising ground voltage
82
ICs
SI-3000ZF Series
(unit : mm)
0.5
10.0
0.2
3.20.2
2.60.1
(2.0)
Pin Assignment q VC w VIN e GND r Vo t ADJ Plastic Mold Package Type Flammability: UL94V-0 Product Mass: Approx. 2.3g
16.90.3
0.95
0.15 +0.2
0.45 0.1
+0.2
3.90.7
(4.3) 8.20.7
1 2 3 4 5
4.60.6
CO
+
(4.6)
(17.9)
VO
R3
*
CIN REF
+ +
R1
5 ADJ
CIN: Input capacitor (Approx. 10F) This capacitor is required when the input line contains inductance or when the wiring is long. CO: Output capacitor (47F or higher) The output voltage may oscillate if a low ESR type capacitor (such as a ceramic capacitor) is used for the output capacitor in SI-3000ZF. R1, R2: Output voltage setting resistors The output voltage can be set by connecting R1 and R2 as shown at left. The recommended value for R2 is 10k or 11k.
VC
ON/ OFF 1
Ta-PD Characteristics
25 With Silicone Grease Heatsink: Aluminum
R2
GND
20
15
10
ICs
83
Applications
Secondary stabilized power supply (local power supply)
Junction Temperature Operating Ambient Temperature Storage Temperature Thermal Resistance (Junction to Ambient Air) Thermal Resistance (Junction to Lead)
j-a j-c
*1: VIN (max), IO1 (max) and IO2 (max) are restricted by the relation PD = (VIN VO1) IO1 + (VIN - VO2) IO2. *2: When mounted on glass-epoxy board of 30 30mm2 (copper laminate area 4.3%) Thermal protection may operate when the junction temperature exceeds 135C.
Electrical Characteristics
Ratings Parameter Symbol min. VO1 Output Voltage Conditions VO2 Conditions VOLINE1 Line Regulation Conditions VOLINE2 Conditions VOLOAD1 Load Regulation Conditions VOLOAD2 Conditions Dropout Voltage VDIF1 Conditions VO1/Ta Temperature Coefficient of Output Voltage Conditions VO2/Ta Conditions RREJ1 Ripple Rejection Conditions RREJ2 Conditions IS1 1 Overcurrent Protection Starting Current*1 Conditions IS1 2 Conditions Quiescent Circuit Current Circuit Current at Output OFF Control Voltage (Output ON)*2 Control Voltage (Output OFF) VC Control Current Terminal (Output ON) Control Current (Output OFF) Output OFF Voltage Iq Conditions Iq (OFF) Conditions VC, IH VC, IL IC, IH Conditions IC, IL Conditions VO(OFF) 100 VC=0.4V 0.5 VC=2.7V 2 0.8 5 VIN=5V, VC=0V 1.2 VIN=5V 1 VIN=5V, IO=0A, VC=2V 0.5 1.5 mA mA V V 1.2 VIN=5V A IO=1A 0.3 Tj=0 to 100C 0.3 Tj=0 to 100C 60 VIN=5V, f=100 to 120Hz 60 VIN=5V, f=100 to 120Hz dB mV/ C VIN=5V, IO=0 to 1A 0.6 V VIN=5V, IO=0 to 1A 30 VIN=4.5 to 10V, IO=10mA 30 mV VIN=4.5 to 10V, IO=10mA 20 2.450 3.234 SI-3002KWM typ. 3.300 VIN=5V, IO=10mA 2.500 VIN=5V, IO=10mA 20 mV 2.550 max. 3.366 V Unit
A A
V
*1: IS1 1 and IS1 2 are specified at the 5% drop points of output voltages VO1 and VO2 on the condition that VIN = the condition of protection starting current, IO = 10 mA. *2: Output is ON when the output control terminal VC is open. Each input level is equivalent to LS-TTL. Therefore, the devices can be driven directly by LS-TTLs. Channels 1 and 2 are turned on or off at the same time.
84
ICs
SI-3000KWM Series
(Unit : mm)
2.300.20 0.500.10
1.100.20
R0 .32 5
6.100.20
0.30
(4.06) 2.70
0.20
9.90
2.700.20
(0.89)
1.180.20
0.1
9.900.30
8 0 to 0.500.10
(1.00)
Plastic Mold Package Type Flammability: UL 94V-0 Product Mass: Approx. 1.48 g
Block Diagram
VIN
4
+
VOUT1
2
AMP2
COUT1
ON/ OFF
+
TSD
CIN: Input capacitor (Approx. 0.1 to 10F) This capacitor is required when the input line contains inductance or when the wiring is long. Co1, Co2: Output capacitor (22F or higher) The output voltage may oscillate if a low ESR type capacitor (such as a ceramic capacitor) is used for the output capacitor in SI-3000KWM.
VOUT2
5
Drive
+
COUT2
OCP
AMP2
GND
3
ICs
85
Selection Guide
2-Phase Stepper Motor Unipolar Driver ICs
Excitation Method Output Current (A)
1.0
SLA7022MU SMA7022MU
1.5
SLA7029M SMA7029M SMA7036M
2.0
3.0
Package ZIP15Pin with Fin ZIP15Pin ZIP15Pin ZIP18Pin with Fin ZIP18Pin with Fin ZIP18Pin with Fin ZIP23Pin with Fin ZIP23Pin with Fin ZIP23Pin with Fin ZIP21Pin with Fin Built-in sequencer
Remarks
2-Phase Excitation
to 46 to 46 to 46 to 46 to 46 to 46 to 46
Built-in sequencer, Current sensing resistors Built-in sequencer, Current sensing resistors, Protection circuit Built-in Current sensing resistors, Protection circuit Built-in sequencer
SLA7070MPR SLA7071MPR SLA7072MPR SLA7073MPR SLA7080MPR SLA7081MPR SLA7082MPR SLA7083MPR 2W 1-2 Phase Excitation Step Support SLA7065M SLA7066M SLA7067M
SI-7321M 4W 1-2 Phase Excitation Step Support SLA7060M SLA7075MR SLA7076MR SLA7061M SLA7077MR SLA7062M SLA7078MR
to 46 to 46 to 46 to 46
HSOP44Pin ZIP21Pin with Fin ZIP23Pin with Fin ZIP23Pin with Fin
Built-in sequencer, Protection circuit Built-in sequencer Built-in sequencer, Current sensing resistors Built-in sequencer, Current sensing resistors, Protection circuit
86
ICs
Surface-mount MOSFET Surface-mount MOSFET Surface-mount MOSFET Full Mould Full Mould Full Mould Full Mould Full Mould Full Mould Full Mould Full Mould With Fin With Fin With Fin With Fin With Fin With Fin With Fin With Fin Full Mould MOSFET MOSFET MOSFET MOSFET MOSFET MOSFET MOSFET MOSFET MOSFET MOSFET MOSFET MOSFET MOSFET MOSFET IGBT IGBT IGBT
3.3V,5V 3.3 V and 5 V input levels are supported UVLO ...... Under voltage lockout protection OCP ........ Over current protection OCL ........ Overcurrent limiting TD ........... Thermal detection TSD .......... Thermal shutdown FO ........... Fault output 3shunt ..... 3 shunt support Boot_Di ... Built-in boot diode STP .......... Shoot through prevention Reg .......... Built-in 7.5 V regulator output Fc ............ Carrier frequency
ICs
87
88
ICs
Application Note
Setup Precautions
Recommended mounting torque 0.588 to 0.784 [Nm](6.0 to 8.0 [kgfcm]) Recommended silicone grease Shin-Etsu Chemical Co., Ltd.: G746 Momentive Performance Materials Inc.: YG-6260 Dow Corning Toray Silicone Co., Ltd.: SC102 Please select proper silicone grease carefully since the oil in some grease products may penetrate the device and result in an extremely short device life.
Handling Precautions
When using the following products that use C-MOS circuits for input terminals, observe the following. SMA7036M/SLA7031M/SLA7032M/SLA7033M SLA7050M/SLA7051M/SLA7052M SLA7060M/SLA7061M/SLA7062M SLA7065M/SLA7066M/SLA7067M SLA7070MR/SLA7071MR/SLA7072MR/SLA7073MR SLA7070MPR/SLA7071MPR/SLA7072MPR/SLA7073MPR SLA7075MR/SLA7076MR/SLA7077MR/SLA7078MR SLA7075MPR/SLA7076MPR/SLA7077MPR/SLA7078MPR SLA7080MPR/SLA7081MPR/SLA7082MPR/SLA7083MPR STA6940M SPI-6631M SX68000M Series SMA6800M Series SLA6800M Series SCM1100M Series SCM1200M Series Carefully control the humidity of the room to prevent the buildup of static electricity. Since static electricity is particularly a problem during the winter, be sure to take sufficient precautions. Take care to make sure that static electricity is not applied to the IC during wiring and assembly. Take precautions such as shorting the terminals of the printed circuit board to ensure that they are at the same electrical potential.
ICs
89
Electrical Characteristics
Ratings Parameter Symbol min. Control Supply Current Control Supply Voltage FET Drain-Source Voltage FET ON Voltage FET Drain Leakage Current IS Condition VS VDSS Condition VDS Condition IDSS Condition VSD Condition IIH TTL Input Current Condition IIL Condition VIH TTL Input Voltage (Active High) Condition VIL Condition VIH TTL Input Voltage (Active Low) Condition VIL Condition ID=1A 0.5 VS=24V, ID=0.8A 0.7 VS=24V, ID=0.8A 0.1 VS=24V, ID=0.8A Tr Condition Switching Time Tstg Condition Tf Condition 2 VDSS=100V 0.8 ID=1A 0.5 VS=24V, ID=1A 0.7 VS=24V, ID=1A 0.1 VS=24V, ID=1A VDSS=100V 2 VDSS=100V 0.8 ID=1A 0.5 VS=24V, ID=0.8A 0.7 VS=24V, ID=0.8A 0.1 VS=24V, ID=0.8A 2 ID=1A 0.8 VDSS=100V 2 VDSS=100V 0.8 ID=1A 0.5 VS=24V, ID=1A 0.7 VS=24V, ID=1A 0.1 VS=24V, ID=1A VIH=2.4V, VS=44V 0.8 VIL=0.4V, VS=44V 2 ID=1A 0.8 VDSS=100V 2 VDSS=100V 0.8 VIL=0.4V, VS=44V 2 ID=1A 0.8 VDSS=100V ID=1A 40 VIH=2.4V, VS=44V 0.8 VDSS=100V, VS=44V 1.2 ID=1A 40 ID=1A, VS=14V 4 VDSS=100V, VS=44V 1.1 ID=1A 40 VIH=2.4V, VS=44V 0.8 VIL=0.4V, VS=44V 2 ID=1A 0.8 10 100 VS=44V, IDSS=250A 0.85 ID=1A, VS=14V 4 VDSS=100V, VS=44V 1.2 ID=1A 40 VIH=2.4V, VS=44V 0.8 VIL=0.4V, VS=44V SLA7022MU typ. 10 VS=44V 24 44 10 100 VS=44V, IDSS=250A 0.6 ID=1A, VS=14V 4 VDSS=100V, VS=44V 1.1 max. 15 min. SLA7029M typ. 10 VS=44V 24 44 10 100 VS=44V, IDSS=250A 0.85 ID=1A, VS=14V 4 max. 15 min. SMA7022MU typ. 10 VS=44V 24 44 10 100 VS=44V, IDSS=250A 0.6 max. 15 min. SMA7029M typ. 10 VS=44V 24 44 max. 15
(Ta=25C) Unit
mA V V V mA V
DC Characteristics
A
mA
AC Characteristics
90
ICs
SLA7022MU/SLA7029M/SMA7022MU/SMA7029M
VS
Reg
Reg
GNDA
GNDB
REFA
REFB
RSA
12
13
11
RSB
9
TDA
TDB
Vb (5V)
8 VS
10
15 INA 5 INA
r3
r4
r1
2 11 TdA TdB RSA REFA REFB RSB 7 3 13 9 C3 Rs C4 Rs GA 4
0 L L
1 L L
2 H L H L
3 H H H L
4 L L H L
5 L L H H
6 L L L L
7 L H L L
0 H L L L
1 H L L H
2 H L H L
3 H H H L
INB GB 12
14
H H
C1
C2
r2
L H
r5
r6
Open collector
tdA
tdB
(1~2W)
(Unit:mm) SMA7022MU/SMA7029MA
16 0.2
13 0.2
10.20.2
9.9 0.2
4.60.6
8.5max
30.6
2.450.2
6.70.5
+1 9.7 0.5
1.45 0.15
6.7 0.5 (9.7)
1.60.6
+0.2
0.55 0.1
+0.2
0.65 0.1
+0.2
4 0.7
P2.030.114=28.42
1 2 3 . . . . . . . 15
12 3 . . . . . . . 15
123 . . . . . . .
12 3 . . . . . . . 15 15
0.55 0.1
(3)
(3)
+0.2
+0.2
0.620.1 1.160.15
(4.6)
ICs
91
Electrical Characteristics
Parameter Control Supply Current Control Supply Voltage FET Drain-Source Voltage FET ON Voltage FET Diode Forward Voltage FET Drain Leakage Current Symbol IS Condition VS VDSS Condition VDS Condition VSD Condition IDSS Condition VIH 2 ID=1A 0.8 VDSS=100V 2 VDSS=100V 0.8 ID=1A 1 VS=44V, VI=0 or 5V 4.0 Synchronous chopping mode 0.8 Asynchronous chopping mode 0.1 VS=44V, VYS=5V 0.1 VS=44V, VYS=0V 0 Reference voltage input 4.0 Output FET OFF 1 No synchronous trigger 40 Resistance between GND and REF terminal at synchronous trigger 1.5 VS=24V, ID=1A 0.5 VS=24V, ID=1A 0.9 VS=24V, ID=1A 0.1 VS=24V, ID=1A 12 VS=24V 5.5 2.0 V mA V V V Condition VIL Condition VIH VDSS=100V, VS=44V ISD=1A 250 ID=1A, VS=10V 1.1 10 100 VS=44V, IDSS=250A 0.6 Ratings min. typ. 10 VS=44V 24 44 max. 15 Unit mA V V V V
Active H
DC Characteristics
IN Terminal
Active L
Input Current
AC Characteristics
Tr Condition Switching Time Tstg Condition Tf Condition Chopping OFF Time TOFF Condition
92
ICs
SMA7036M
IN A
IN B
Vs
Excitation input signal Active H Active L OUT A OUT A OUT A OUT A OUT B OUT B OUT B OUT B
SYNC A
SYNC B
REF A
REF B
GND A
GND B
Rs A
13
12
11
Rs B
8 VS 2 SyncA
10
15
0 H L
1 H H
2 L H
3 L L
0 H L
1 H H
INA INB
SMA7036M Vb (5V) 11 PchMOS r1 RsA 7 Rs RefA RefB 3 13 RsB 9 Rs GA 4 GB 12 SyncB INB 14 INB
r2
: : : : :
(Unit : mm)
Epoxy resin package
2.5 0.2
3 0.6 1.6 0.6 (4.6) 0.55 0.1
+0.2
40.2
8.5max
1.45 0.15
6.7 0.5 (9.7)
(3)
+0.2
4 0.7
1 2 3 . . . . . . . . 15
12 3 . . . . . . . 15
ICs
93
SLA7027MU/SLA7024M/SLA7026M
Electrical Characteristics
Ratings Parameter Symbol min. Control Supply Current Control Supply Voltage FET Drain-Source Voltage FET ON Voltage FET Drain Leakage Current IS Condition VS VDSS Condition VDS Condition IDSS Condition VSD Condition IIH TTL Input Current Condition IIL Condition VIH TTL Input Voltage (Active High) Condition VIL Condition VIH TTL Input Voltage (Active Low) Condition VIL Condition ID=1A 0.5 VS=24V, ID=0.8A 0.7 VS=24V, ID=0.8A 0.1 VS=24V, ID=0.8A Tr Condition Switching Time Tstg Condition Tf Condition 2 VDSS=100V 0.8 ID=1A 0.5 VS=24V, ID=1A 0.7 VS=24V, ID=1A 0.1 VS=24V, ID=1A VDSS=100V 2 VDSS=100V 0.8 ID=3A 0.5 VS=24V, ID=1A 0.7 VS=24V, ID=1A 0.1 VS=24V, ID=1A 2 ID=1A 0.8 VDSS=100V 2 VDSS=100V 0.8 V VIL=0.4V, VS=44V 2 ID=1A 0.8 VDSS=100V VIH=2.4V, VS=44V 0.8 VIL=0.4V, VS=44V 2 ID=3A 0.8 V ID=1A 40 VIH=2.4V, VS=44V 0.8 VIL=0.4V, VS=44V VDSS=100V, VS=44V 1.2 ID=1A 40 VIH=2.4V, VS=44V 0.8 ID=1A, VS=14V 4 VDSS=100V, VS=44V 1.1 ID=3A 40 10 100 VS=44V, IDSS=250A 0.85 ID=1A, VS=14V 4 VDSS=100V, VS=44V 2.3 SLA7027MU typ. 10 VS=44V 24 44 10 100 VS=44V, IDSS=250A 0.6 ID=3A, VS=14V 4 max. 15 min. SLA7024M typ. 10 VS=44V 24 44 10 100 VS=44V, IDSS=250A 0.85 max. 15 min. SLA7026M typ. 10 VS=44V 24 44 max. 15 mA V V V mA V Unit
DC characteristics
A
mA
AC characteristics
94
ICs
SLA7027MU/SLA7024M/SLA7026M
Reg
Reg
REFA
REFB
RSA
3 14
13
15
RSB 10
TDA
TDB
GA
GB
Vb (5V)
1 18 OUTA OUTB
11 OUTB INA INA INB GA 4 INB GB 15 6 5 17 16 INA INA INB INB Active High
INB INB
r3
r4
r1
2 TdA TdB
C1
C2
13
r2
Rs
r5
r6
Rs
510 100 (VR) : 47k : 47k : 2.4k : 2.4k : 470pF : 470pF : 2200pF : 2200pF : 1 typ (7024M) (1 to 2W) 0.68 typ (7026M) 1.8 typ (7027MU)
: :
r1 r2 r3 r4 r5 r6 C1 C2 C3 C4 Rs
Active Low
VCC (46V max)
0 L H L H
1 H L L H
2 H L H L
3 L H H L
0 L H L H
1 H L L H
INA INA
Vb (5V) 7 12 8 1 18 VSA VSB OUTA OUTA OUTB 11 OUTB INA INA INB GA 4 INB GB 15 6 5 17 16 INA INA INB INB Active Low
INB INB
r3
r4
r1
2 TdA TdB 13
C1
C2
r2
Rs
r5
r6
r1 r2 r3 r4 r5 r6 C1 C2 C3 C4 Rs
(1 to 2W)
: : : : : : : : : : :
Rs
510 100 (VR) 47k 47k 2.4k 2.4k 470pF 470pF 2200pF 2200pF 1 typ (7024M) 0.68 typ (7026M) 1.8 typ (7027MU)
(Unit : mm)
3.20.153.8
16 0.2
13 0.2
9.9 0.2
6.70.5
R-End
+0.2 0.65 0.1 +0.2 1 0.1
9.7 0.5
+1
(3)
0.65 0.1
1 0.1
+0.2
17P1.680.4=28.561 31.30.2
17P1.680.4=28.561
1 2 3 . . . . . . . 18
123 . . . . . . . 18
+0.2
+0.2
+0.2
3 0.6
2.450.2
4.6 0.6
ICs
95
SLA7031M/SLA7032M/SLA7033M
SLA7031M
VCC VS VDSS VIN VSYNC VREF VRS IO PD1 PD2 Tch Ta Tstg
SLA7032M SLA7033M 46 46 100 0.3 to +7 0.3 to +7 0.3 to +7 5 to +7 1.5 3 4.5(Without Heatsink) 35(Tc=25C) +150 20 to+85 40 to +150
Unit
V V V V V V A W W
C C C
VM VS VREF VREF(dis) TC
Unit
Remarks
V V V V
C
The control current precision is degraded at 0.1V or lower. Output MOS FET OFF Temperature of 4(15)-Pin Lead(without heatsink)
Electrical Characteristics
Ratings Parameter Symbol min. Control Supply Current Control Supply Voltage FET Drain-Source Voltage FET ON Voltage FET Diode Forward Voltage FET Drain Leakage Current IS Condition VS VDSS Condition VDS Condition VSD Condition IDSS Condition VIH Input Voltage (Active High) Condition VIL Condition VDSS=100V 2.0 VDSS=100V 0.8 ID=1A 1 VS=44V, VI=0 or 5V 4.0 Synchronous chopping mode 0.8 Asynchronous chopping mode 0.1 VS=44V, VSYNC=5V 0.1 VS=44V, VSYNC=0V 0 Reference Voltage input 4.0 Output FET OFF 1 No synchronous trigger 40 Resistance between GND and REF terminal at synchronous trigger VREF 0.5 0.7 0.1 VS=24V, ID=0.8A 12 VS=24V No synchronous trigger 40 Resistance between GND and REF terminal at synchronous trigger VREF 0.5 0.7 0.1 VS=24V, ID=1A 12 VS=24V 5.5 4.0 Output FET OFF 1 No synchronous trigger 40 Resistance between GND and REF terminal at synchronous trigger VREF 0.5 0.7 0.1 VS=24V, ID=1A 12 VS=24V 2.0 0 Reference Voltage input 5.5 4.0 Output FET OFF 1 VS=44V, VSYNC=0V 2.0 0 Reference Voltage input 5.5 VS=44V, VSYNC=5V 0.1 VS=44V, VSYNC=0V 2.0 V 4.0 Synchronous chopping mode 0.8 Asynchronous chopping mode 0.1 VS=44V, VSYNC=5V 0.1 VS=44V, VI=0 or 5V 4.0 Synchronous chopping mode 0.8 Asynchronous chopping mode 0.1 mA V ID=1A 1 VS=44V, VI=0 or 5V 2.0 VDSS=100V 0.8 ID=3A 1 VIH Input Voltage (Active Low) Condition VIL Condition Input Current II Condition VSYNC Input Voltage SYNC Terminal Input Current Condition VSYNC Condition ISYNC Condition ISYNC Condition VREF Input Current REF Terminal Input Current Internal Resistance Sense Voltage Condition VREF Condition IREF Condition RREF Condition VRS Tr Switching Time Tstg Tf Condition Chopping OFF Time TOFF Condition 2.0 ID=1A 0.8 VDSS=100V 2.0 VDSS=100V 0.8 V VDSS=100V, VS=44V 2.0 ID=1A 0.8 VDSS=100V ISD=1A 250 VDSS=100V, VS=44V 2.0 ID=3A 0.8 V ID=1A, VS=10V 1.2 ISD=1A 250 VDSS=100V, VS=44V 10 100 VS=44V, IDSS=250A 0.85 ID=1A, VS=14V 1.1 ISD=3A 250 SLA7031M typ. 10 VS=44V 24 44 10 100 VS=44V, IDSS=250A 0.6 ID=3A, VS=14V 2.3 max. 15 min. SLA7032M typ. 10 VS=44V 24 44 10 100 VS=44V, IDSS=250A 0.85 max. 15 min. SLA7033M typ. 10 VS=44V 24 44 max. 15 mA V V V V Unit
DC characteristics
IN Terminal
A
V
AC characteristics
96
ICs
SLA7031M/SLA7032M/SLA7033M
12
17
16
11
18
Reg.
Reg.
Excitation input signal Active H Active L OUT A OUT A OUT A OUT A OUT B OUT B OUT B OUT B
SYNC A
SYNC B
REF A
REF B
Rs A
14
15
13
10
Rs B
GA
GB
clock IN A IN A IN B IN B
0 H L H L
1 L H H L
2 L H L H
3 H L L H
0 H L H L
Vb (5V)
13
SYNC B
r1
RsA 9 Rs
GA 4
GB 15
r2
Active Low
Vcc (46Vmax)
0 L H L H
1 H L L H
2 H L H L
3 L H H L
0 L H L H
IN A
INA 6
OUTA OUTA OUTB OUTB INA INA INB INB Active Low
IN A IN B IN B
Vb (5V)
13
SYNC B
r1
RsA 9 Rs
GA 4
GB 15
r2
(Unit : mm)
3.20.153.8
16 0.2
13 0.2
9.9 0.2
6.70.5
R-End
+0.2 0.65 0.1 +0.2 1 0.1
9.7 0.5
+1
0.55 0.1
+0.2
(3)
0.65 0.1
1 0.1
+0.2
17P1.680.4=28.561 31.30.2
1 2 3 . . . . . . . 18
123 . . . . . . . 18
1.6 0.6
+0.2
+0.2
2.20.6
3 0.6
2.450.2
4.6 0.6
ICs
97
Electrical Characteristics
Ratings Parameter Symbol min. ISS Main Supply Current Conditions IS Conditions Logic Supply Current Output MOSFET Breakdown Voltage Output MOSFET ON Resistance Output MOSFET Diode Forward Voltage Maximum Clock Frequency Logic Input Voltage Logic Input Current ICC VDSS Conditions RDS (ON) Conditions VSD Conditions Fclock VIL VIH IIL IIH VREF REF Input Voltage Conditions VREFS Conditions REF Input Current Sense Voltage PWM OFF Time PWM Minimum ON Time Sleep - Enable Recovery Time IREF VRS TOFF TON (min) TSE Conditions TONC Switching Time Conditions TOFFC Conditions 100 VREF : 2.01.5V, IO : 0.75A 2.5 ClockOut 2.0 ClockOut 0 2 Output OFF (sleep) 10 VREF 12 5 100 VREF : 2.01.5V, IO : 1.5A 2.5 ClockOut 2.0 ClockOut VCC0.75 1 1 1.5 VCC 0 2 Output OFF (sleep) 10 VREF 12 5 Normal-operation current control ISD=1A 100 VCC0.25 VCC0.75 1 1 1.5 VCC ID=1A 1.2 ISD=1A 100 VCC0.25 100 VS=44V, IDSS=1mA 0.85 ID=1A 1.1 Sleep mode 3 100 VS=44V, IDSS=1mA 0.5 Normal operation 100 Sleep mode 3 SLA7050M typ. max. 15 Normal operation 100 min. SLA7051M typ. max. 15
(VCC = 5V, V S = 24V, Ta = 25C, unless otherwise specified) SLA7052M min. typ. Normal operation 100 Sleep mode 3 100 VS=44V, IDSS=1mA 0.27 ID=3A 2.3 ISD=3A 100 VCC0.25 VCC0.75 1 1 0 2 Output OFF (sleep) 10 VREF 12 5 100 VREF : 2.01.5V, IO : 2.0A 2.5 ClockOut 2.0 ClockOut 1.5 VCC V Normal-operation current control max. 15 mA Unit
A
mA V V kHz V
A
V
S S S
98
ICs
SLA7050M/SLA7051M/SLA7052M
OutB
Pin No.
1 2
Symbol OutA NC OutA/ GA VCC SenseA Clock Sync Ref GND CW/CCW Full/Half SenseB VS GB OutB/ NC OutB Phase A output No Connection Phase A output No Connection Logic supply Phase A current sense Step Clock input
Function
Vcc
GA
GB
Truth Table
L CW/CCW Full/Half REF Sync Clock CW Full Enable Asynchronous H CCW Half Disable Synchronous
* REF terminal turns into normal operation at VREF < 1.5V. The output is disabled (Output OFF) at VREF > 2V.
CB
16 0.2
13 0.2
9.9 0.2
6.70.5
9.7 0.5
+1
+0.2
(3)
0.65 0.1
1 0.1
+0.2
17P1.680.4=28.561
1 2 3 . . . . . . . 18
123 . . . . . . . 18
+0.2
+0.2
+0.2
3 0.6
2.450.2
4.6 0.6
NC
2 6
NC
Vs
11 12
14 Reg
15
16
17
18
MIC
GA
3
GB Sequencer GA/ OSC PWM Control Sleep Circuit Synchro Control GB/ OSC PWM Control
4 5 6 7 8 9 10
Synchronous PWM control signal input Control current setting & output OFF Device GND Normal/reverse control input Full/Half Step control input Phase B current sense Load supply (motor supply) No Connection Phase B output No Connection Phase B output
10
13
11 12 13 14 15 16 17 18
SenseB
SenseA
REF
OutA/
Sync
GND
14
15
17
16 18
. 2 Rs=0.1 to 2 (Power dissipation should be: P= .IO RS) R1=10k CA=100F/50V R2=5.1k (VR) CB=10F/10V Q1:T.B.D * VCC line noise precaution: The device may malfunction if the VCC line noise exceeds 0.5V. * Be sure to connect the unused logic input terminals (CW/CCW, F/H, Sync) to VCC or GND. If they are open, the device will malfunction. * GND pattern precaution: Separating the VCC system GND (S-GND) and VS system GND (P-GND) from the device GND (10-Pin) helps to reduce noise.
OutB/
OutA
CW/CCW Full/Half Sync REF 6 r2 RsA S-GND
OutB
GA
GB
NC
NC
Vs
10
13 RsB
SenseA
GND
P-GND
SenseB
(Unit : mm)
3.20.153.8
ICs
99
SLA7070MR, MPR/7071MR, MPR/7072MR, MPR/7073MR, MPR 2-Phase/1-2 Phase Excitation Support, Built-in Sequencer
Features
Lineup of built-in current sense resistor and built-in protection circuit-type Power supply voltages, VBB: 46 V (max), 10 to 44 V normal operating range Logic supply voltages, VDD: 3.0 to 5.5 V Maximum output currents: 1 A, 1.5 A, 2 A, and 3A Built-in sequencer Self-excitation PWM current control with fixed off-time Synchronous PWM chopping function prevents motor noise in Hold mode Sleep mode for reducing the IC input current in stand-by state ZIP type 23-pin molded package (SLA package)
46 46 6 *1
0.3 to VDD+0.3 0.3 to VDD+0.3
2 4.7 17 +150
20 to +85 30 to +150
V V V A V V V W C C C
Mode F
*1: Output current value may be limited for the SLA7070MR, MPR (1.0 A), SLA7071MR, MPR (1.5 A), SLA7072MR, MPR (2.0 A), and SA7073MR, MPR (3.0 A), depending on the duty ratio, ambient temperature, and heating conditions. Be sure that junction temperature of Tj is not exceeded under any circumstances.
Electrical Characteristics
Parameter Main Supply Current Logic Supply Current Output MOSFET Breakdown Voltage Output MOSFET ON Resistance Symbol
IBB IBBS Icc V(BR)DSS RDS(ON)
min.
Ratings typ.
max. 15 100 5
Unit mA A mA V In operation Sleep 1 and Sleep 2 modes VBB=44V, ID=1mA SLA7070M, ID=1.0A SLA7071M, ID=1.5A SLA7072M, ID=2.0A SLA7073M, ID=3.0A SLA7070M, ID=1.0A SLA7071M, ID=1.5A SLA7072M, ID=2.0A SLA7073M, ID=3.0A When Clock Duty = 50%
Conditions
100 0.7 0.45 0.25 0.18 0.85 1.0 0.95 0.95 250 0.25VDD 0.75VDD 1 1 0.04 0.04 0.04 0.04 2 10 VREF 100 2.0 1.5 0.305 0.305 0.205 0.155 0.7 2.3 3.5 4.6 0.3 0.45 0.4 0.45 VDD 0.85 0.6 0.4 0.24 1.1 1.25 1.2 2.1
VF
V kHz V A
Fclock VIL VIH IIL IIH VREF VREFS IREF VSENSE TSE tcon tcoff RS
SLA7070MR/7070MPR, within the current setting range SLA7071MR/7071MPR, within the current setting range SLA7072MR/7072MPR, within the current setting range SLA7073MR/7073MPR, within the current setting range Output (OFF) Sleep 1 When step reference current ratio is 100% Sleep1&Sleep2 Clock Out ON Clock Out OFF SLA7070MR/7070MPR, tolerance of 3% SLA7071MR/7071MPR, tolerance of 3% SLA7072MR/7072MPR, tolerance of 3% SLA7073MR/7073MPR, tolerance of 3% SLA7070MPR/7071MPR/7072MPR/7073MPR, when motor coil shorts out SLA7070MPR/7071MPR SLA7072MPR SLA7073MPR SLA7070MPR/7071MPR/7072MPR/7073MPR, IFlagL=1.25mA SLA7070MPR/7071MPR/7072MPR/7073MPR, IFlagH=1.25mA SLA7070MPR/7071MPR/7072MPR/7073MPR
REF Input Current Sense Voltage Sleep-Enable Recovery Time Switching Time
Sense Resistance
Overcurrent Sense Voltage Overcurrent Sense Current Flag Output Voltage Flag Output Current Step Reference Current Ratio PWM Minimum ON Time PWM OFF Time
Vocp Iocp VFlagL VFlagH IFlagL IFlagH ModeF Mode8 ton(min) toff
* The direction in which current flows out of the device is regarded as negative.
100
ICs
Pin Assignment
Pin No. Symbol Function
14
15
18
9 16 10 15
11
20 21 22 23
MIC
PreDriver Sequencer & Sleep Circuit
Reg
PreDriver
Protect
Protect
DAC
DAC
+
SenseA
PWM Control
PWM Control
RS
OSC
OSC
17
12
The protect circuit is deleted and the flag pin is N.C. for SLA7070MR, 7071MR, 7072MR, and 7073MR.
12.90.2
160.2
BB
OutB OutB
9.90.2
R-end
+0.2
Ref/Sleep SenseA
(4.3)
0.55 0.1
0.7
+0.2
Gnd
SenseB
r2
r3
C2
Logic Gnd
Power Gnd
9.5 0.5
M1
50.5
+1
Synchro Control
19
SenseB
RS
1 Phase A output OutA 2 3 Phase A output OutA/ 4 SenseA Phase A current sense 5 6 N.C. N.C. M1 7 M2 Excitation mode/Sleep 2 setting input 8 9 M3 Clock Step Clock input 10 VBB Driver supply (motor supply) 11 12 Gnd Device GND Ref/Sleep1 Control current mode/Sleep 1 setting input 13 VDD Logic supply 14 15 Reset Internal logic reset input CW/CCW Normal/reverse control input 16 Sync PWM control signal input 17 18 Protection circuit monitor output*1 Flag SenseB Phase B current sense 19 20 OutB/ Phase B current output 21 22 OutB Phase B current output 23 *1: N.C. pin for SLA7070MR, 7071MR, 7072MR, and 7073MR.
Ref/Sleep1
CW/CCW
Reset
Clock
OutA
OutA
OutA
OutA
OutB
OutB
OutB
OutB
N.C.
Flag
VDD
VBB
M1
M2
M3
3.20.15 3.8
CA
3.20.15
ICs
101
SLA7080MPR/7081MPR/7082MPR/7083MPR
Features
Lineup of built-in current sense resistor and built-in protection circuit-type Power supply voltages, VBB: 46 V (max), 10 to 44 V normal operating range Logic supply voltages, VDD: 3.0 to 5.5 V Maximum output current Io: 1A, 1.5A, 2A, and 3A Self-excitation PWM current control with fixed off time Synchronous PWM chopping function prevents motor noise in Hold mode Sleep mode for reducing the IC input current in stand-by state ZIP type 23-pin molded package (SLA package)
2-Phase/1-2-Phase Excitation
(Ta=25C)
Unit V V V A V V V W C C C
Conditions
*1: Output current value may be limited for the SLA7080MPR(1.0A), SLA7081MPR(1.5A), SLA7082MPR(2.0A), SLA7083MPR(3.0A), depending on the duty ratio, ambient temperature, and heating conditions. Do not exceed junction temperature of Tj under any circumstances.
Motor Supply Voltage Driver Supply Voltage Logic Supply Voltage REF Input Voltage Case Temperature
Unit
Conditions
V V V V C
The VDD surge voltage should be 0.5V or lower. When controlling the current for SLA7080M When controlling the current for SLA7081M/SLA7083M When controlling the current for SLA7082M Rear center (without Fin)
Electrical Characteristics
Parameter
Main Supply Current Logic Supply Current Output MOSFET Breakdown Voltage Output MOSFET ON Resistance
Symbol
IBB IBBS IDD V(BR)DSS RDS(ON)
min.
Ratings typ.
max.
15 100 5
Unit
mA A mA V In operation Sleep Mode VBB=44V, ID=1mA SLA7080M, ID=1.0A SLA7081M, ID=1.5A SLA7082M, ID=2.0A SLA7083M, ID=3.0A SLA7080M, ID=1.0A SLA7081M, ID=1.5A SLA7082M, ID=2.0A SLA7083M, ID=3.0A When Duty = 50%
Conditions
100 0.7 0.45 0.25 0.18 0.85 1.0 0.95 0.95 250 0.25VDD 0.75VDD 1 1 0.04 0.04 0.04 0.04 2.0 VREF0.03 0.296 0.296 0.199 0.150 10 VREF 0.305 0.305 0.205 0.155 3.2 5.2 13 1.5 1.0 0.7 2.3 3.5 4.5 2.0 140 0.3 0.45 0.4 0.45 VDD VREF+0.03 0.314 0.314 0.211 0.160 0.85 0.6 0.4 0.24 1.1 1.25 1.2 2.1
Output MOSFET Diode Forward Voltage Maximum Clock Frequency Logic Input Voltage Logic Input Current
V kHz V
A
SLA7080M SLA7081M SLA7082M SLA7083M Sleep (IBBS, output: OFF)
REF Input Current Sense Voltage Sense Resistance PWM Minimum ON Time (blanking time) PWM OFF Time Sleep-Enable Recovery Time Switching Time Overcurrent Sense Voltage Overcurrent Sense Current VocpRs Time Not Sensing Load Disconnection Thermal Protection Temperature
A V
Including the resistance due to the product configuration (about 5 m ) for SLA7080M Including the resistance due to the product configuration (about 5 m ) for SLA7081M Including the resistance due to the product configuration (about 5 m ) for SLA7082M Including the resistance due to the product configuration (about 5 m ) for SLA7083M B_SEL: Low B_SEL: High Sleep Phase IN Out ON Phase IN Out OFF When the motor coil shorts out SLA7080MPR/7081MPR SLA7082MPR SLA7083MPR Rear of case (at the saturation temperature) IFlagL= 1.25mA IFlagH= 1.25mA
s s S S S V
A 2.5 1.25 1.25
0.65
0.75
topp 1.5 Ttsd VFlagL Flag Output Voltage VFlagH 1.25VDD IFlagL Flag Output Current IFlagH 1.25 *The direction in which current flows out of the device is regarded as negative.
S C
V mA
102
ICs
SLA7080MPR/7081MPR/7082MPR/7083MPR
Pin Assignment
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Symbol Out A /Out A Sense A B_SEL INA /INA INB /INB VBB Gnd Ref/Sleep VDD Gnd1 Gnd2 Sync Flag Sense B /Out B Out B Function Phase A output Phase A output Phase A current sense Blanking time switching input Phase A switching input Phase B switching input Driver supply (motor supply) Device GND Control current/Sleep setting input Logic supply Gnd1 Gnd2 PWM synchronous/asynchronous switching input Protection circuit monitor output Phase B current sense Phase B output Phase B output
(Unit : mm)
12.90.2
160.2
3.20.15
9.90.2
50.5
4(R1)
R-end
(4.3)
22P1.270.5=27.941
0.55 0.1
+0.2
9.5 0.5
+1
ICs
103
(Ta=25C) Unit V V V A V V V W C C C
Electrical Characteristics
Parameter Symbol min. Main Supply Current Logic Supply Current Output MOSFET Breakdown Voltage Output MOSFET ON Resistance Output MOSFET Diode Forward Voltage Maximum Clock Frequency Logic Input Voltage IBB Conditions IBBS Conditions IDD V (BR) DS Conditions RDS (ON) Conditions VF Conditions fclk Conditions VIL VIH IIL IIH Conditions IILM IIH Conditions VREF Conditions VREFS Conditions IREF VMoL Conditions VMoH Conditions IMoL IMoH ISENSE VSENSE Conditions Mode F Mode E Mode C Mode A Mode 8 Mode 6 Mode 4 Mode 2 Conditions TONC Conditions TOFFC Conditions TON (min) Conditions tOFF1 Conditions tOFF2 Conditions tOFF3 Conditions SLA7065M typ. In operation 100 Sleep mode 4 100 VBB=44V, ID=1mA 0.7 ID=1A 0.85 IF=1A 250 When Clock Duty = 50% VDD0.25 VDD0.75 1 1 Clock, Reset, CW/CCW, Sync 50 1 M1, M2 0 1.5 Normal-operation current control 2 VDD Output OFF (sleep) 10 1.25 IMOL=1.5mA VDD1.25 IMOH=1.5mA 3 3 10 0.95 1.00 1.05 When VREF = 1V in Mode F 100 98.1 92.4 83.1 70.7 55.5 38.2 19.5 . VREF= .VSENSE=100%, VREF=0.1 to 1.0V 2.0 ClockOutON 1.5 ClockOutOFF 1.8 Mode 2 to F 12 Mode 8 to F 9 Mode 4 to 6 7 Mode 2 250 100 VBB=44V, ID=1mA 0.25 ID=2A 0.95 IF=2A Sleep mode 4 max. 15 min. Ratings SLA7066M typ. In operation 100 max. 15
(VDD=5V, VBB=24V, Ta=25C, unless otherwise specified) SLA7067M typ. In operation 100 Sleep mode 4 100 VBB=44V, ID=1mA 0.18 ID=3A 0.95 IF=3A 250 When Clock Duty = 50% VDD0.25 VDD0.75 1 1 Clock, Reset, CW/CCW, Sync 50 1 M1, M2 0 1.5 Normal-operation current control 2 VDD Output OFF (sleep) 10 1.25 IMOL=1.5mA VDD1.25 IMOH=1.5mA 3 3 10 0.95 1.00 1.05 When VREF = 1V in Mode F 100 98.1 92.4 83.1 70.7 55.5 38.2 19.5 . VREF = .VSENSE=100%, VREF=0.1 to 1.0V 2.0 ClockOutON 1.5 ClockOutOFF 1.8 Mode 2 to F 12 Mode 8 to F 9 Mode 4 to 6 7 Mode 2 Unit max. 15 mA
min.
A
mA V V kHz V
Switching Time
When Clock Duty = 50% VDD0.25 VDD0.75 1 1 Clock, Reset, CW/CCW, Sync 50 1 M1, M2 0 1.5 Normal-operation current control 2 VDD Output OFF (sleep) 10 1.25 IMOL=1.5mA VDD1.25 IMOH=1.5mA 3 3 10 0.95 1.00 1.05 When VREF = 1V in Mode F 100 98.1 92.4 83.1 70.7 55.5 38.2 19.5 . VREF= .VSENSE=100%, VREF=0.1 to 1.0V 2.0 ClockOutON 1.5 ClockOutOFF 1.8 Mode 2 to F 12 Mode 8 to F 9 Mode 4 to 6 7 Mode 2
A
V
mA
A
V
s s
* The direction in which current flows out of the device is regarded as negative.
104
ICs
SLA7065M/SLA7066M/SLA7067M
Pin Assignment
Pin No. 1 2
21
Symbol OutA OutA/ SenseA VDD REF Reset CW/CCW Clock GND M2 M1 MO Sync VBB SenseB OutB/ OutB Phase A output Phase A output
Function
14 13 12
9 10
16 Reg
18
19 20
3 4 5 6
MIC
PreDriver Sequencer & Sleep Circuit
Phase A current sense Logic supply Control current setting & output OFF control input Internal logic reset input Normal/reverse control input Step Clock input Device GND Excitation mode setting input 2-phase excitation state monitor output PWM control signal input Driver supply (motor supply) Phase B current sense Phase B output Phase B output
PreDriver
7 8 9 10
DAC
+
11 12 13
17
OSC
14 15 16 17 18 19 20 21
SenseB
CA
VDD=3.0~5.5V
Disable Q1 Reset CW/CCW CB Clock R1 C1
* VDD line noise precaution: The device may malfunction if the VDD line noise exceeds 0.5V. As a countermeasure, separating the VDD system GND (S-GND) and VBB system GND (P-GND) from the device GND (Pin-11) helps to reduce noise. * Be sure to connect the unused logic input terminals (CW/CCW, M1, M2, Reset, Sync) to VDD or GND. Otherwise, the device will malfunction.
OutA/
OutB/
OutA
OutB
VBB
6 8 9 10 12 13 14 15 7
16
18
19
20
21
SLA7060M Series
5
SenseA
11
17
SenseB
REF
R3
R2
RsA
RsB
GND
S-GND
P-GND
Component Values (Typical) . 2 Rs=0.1 to 2 (Power dissipation should be: P= .IO Rs) R1=10k CA=100F/50V R2=5.1k (VR) CB=10F/10V R3=10k C1=0.1F
(Unit : mm)
3.20.153.8
4.80.2 1.70.1
3.20.153.8
4.80.2 1.70.1 30.5 [Measured at the tip] [4.6] 1.60.5 [Measured at the tip]
160.2 [Heatsink]
3.20.15
12.90.2 9.90.2
3.20.15
17.90.6
9.90.2 2.450.2 [Measured at the root] 4 [R1] R-end 12.90.2
160.2 [Heatsink]
50.5
4.2MIN
+0.2
0.55 0.1
+0.2
60.6 7.50.6
+0.2
1 2
3 4
5 6
7 8
11 13 15 17 19 21 10 12 14 16 18 20
0.55 0.1
+0.2
ICs
105
(Ta=25C)
*: Output current value may be limited, depending on the duty ratio, ambient temperature, and heating conditions. Do not exceed junction temperature of Tj under any circumstances.
Motor Supply Voltage Driver Supply Voltage Logic Supply Voltage REF Input Voltage Case Temperature
Unit
Conditions
V V V V
The VDD surge voltage should be 0.5V or lower. When not using protection When using protection Temperature at the center of the package
Electrical Characteristics
Parameter
Driver Supply Current Logic Supply Current Output MOSFET Breakdown Voltage Output MOSFET ON Resistance Output MOSFET Diode Forward Voltage Maximum Clock Frequency Logic Input Voltage Logic Input Current REF Input Voltage REF Input Current Logic Output Voltage Logic Output Current Sense Voltage Overcurrent Sense Voltage
Symbol
IBB IBBS IDD V(BR)DSS RDS(ON) VF Fclk VIL VIH IIL IIH VREF VREFS IREF VLOL VLOH ILOL ILOH VSENSE Vocp Mode F Mode E Mode D Mode C Mode B Mode A Mode 9 Mode 8 Mode 7 Mode 6 Mode 5 Mode 4 Mode 3 Mode 2 Mode 1 TSE tpdon1 on(min) toff1 toff2 toff3 topp
min.
Ratings typ.
max.
15 100 5
Unit
mA A mA V V kHz V In operation Sleep Mode VBB=44V, ID=1mA ID=1.5A IF=1.5A When Duty = 50%
Conditions
100 0.25 0.95 250 0.25VDD 0.75VDD 1 1 0.04 0.04 2 10 1.25 VDD-1.25 1.25 1.25 0.65 0.2 0.7 100 98.1 95.7 92.4 88.2 83.1 77.3 70.7 63.4 55.5 47.1 38.2 29.0 19.5 9.8 2.0 1.5 1.8 3.6 13 9.5 7.5 2 0.75 1.5 0.6 VDD 0.4 1.2
A
V When not using protection When using protection Sleep1 Mode VREF=0 to VDD ILOL=1.25mA ILOH=1.25mA
Sleep-Enable Recovery Time Switching Time PWM Minimum ON Time PWM OFF Time Time Not Sensing Load Disconnection
100
1.5
2.5
A V V mA mA V V % % % % % % % % % % % % % % % S S S s s s s s s
VREF=0.04V to 1.5V
Sleep1&Sleep2 Clock Out ON Clock Out OFF B_SEL: L B_SEL: H Mode8 to F Mode4 to 7 Mode1 to 3 Starts when the PWM is turned off.
The direction in which current flows out of the device is regarded as negative.
106
ICs
SI-7321M
Pin Assignment
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Symbol Out/A Out/A N.C. RsA G/A Gnd1 E_SEL P_SEL Sync CW/CCW Reset Clock M1 M2 M3 B_SEL Gnd1 G/B RsB N.C. Out /B Out /B OutB OutB N.C. RsB GB Gnd1 Gnd2 Flag Mo VDD Ref/Sleep1 Gnd3 N.C. VBB N.C. Gnd4 Gnd1 GA RsA N.C. Out A Out A Function Phase A output Phase A output No connection Connection terminal for phase A sense resistor Phase A MOSFET gate Device Gnd1 Edge selection input Protection use selection input PWM control signal input Normal/reverse control input Internal logic reset input Step clock input Excitation mode/Sleep 2 setting input Blanking time selection input Device Gnd1 Phase B MOSFET gate Connection terminal for phase B sense resistor No connection Phase B output Phase B output Phase B output Phase B output No connection Connection terminal for phase B sense resistor Phase B MOSFET gate Device Gnd1 Device Gnd2 Protection circuit monitor output 2-phase excitation state monitor output Logic supply Control current mode/Sleep 1 setting input Device Gnd3 No connection Driver supply (motor supply) No connection Device Gnd4 Device Gnd1 Phase A MOSFET gate Connection terminal for phase A sense resistor No connection Phase A output Phase A output
(Unit : mm)
7.50.2
1.50 TYP 2.17
9.90.3
2.20.1
0 to 10
0.10
0.220.05
0.100.05
0.65
0.50.2
0.12 M
ICs
107
(Ta=25C) Unit
V V V A V V V W
C C C
The VDD surge voltage should be 0.5V or lower. The control current precision is degraded at 0.1V or lower. Temperature at Pin-11 Lead (Without heatsink)
Electrical Characteristics
Parameter Symbol IBB Conditions IBBS Conditions IDD V (BR )DS Conditions RDS (ON) Conditions VF Conditions fclk Conditions VIL VIH IIL IIH Conditions IILM IIH Conditions VREF Conditions VREFS Conditions IREF VMoL Conditions VMoH Conditions IMoL IMoH ISENSE VSENSE Conditions Mode F Mode E Mode D Mode C Mode B Mode A Mode 9 Mode 8 Mode 7 Mode 6 Mode 5 Mode 4 Mode 3 Mode 2 Mode 1 Conditions TONC Conditions TOFFC Conditions TON (min) Conditions tOFF1 Conditions tOFF2 Conditions tOFF3 Conditions min. SLA7060M typ. In operation 100 Sleep mode 4 100 VBB=44V, ID=1mA 0.7 ID=1A 0.85 IF=1A 250 When Clock Duty = 50% VDD0.25 VDD0.75 1 1 Clock, Reset, CW/CCW, Sync 50 1 M1, M2 0 1.5 Normal-operation current control 2 VDD Output OFF (sleep) 10 1.25 IMOL=1.5mA VDD1.25 IMOH=1.5mA 3 3 10 0.95 1.00 1.05 When VREF = 1V in Mode F 100 98.1 95.7 92.4 88.2 83.1 77.3 70.7 63.4 55.5 47.1 38.2 29 19.5 9.8 . VSENSE=100%, VREF=0.1 to 1.0V VREF= . 2.0 ClockOutON 1.5 ClockOutOFF 1.8 Mode 1 to F 12 Mode 8 to F 9 Mode 4 to 7 7 Mode 1 to 3 250 100 VBB=44V, ID=1mA 0.25 ID=2A 0.95 IF=2A Sleep mode 4 max. 15 min. Ratings SLA7061M typ. In operation 100 max. 15
(VDD=5V, VBB=24V, Ta=25C, unless otherwise specified) SLA7062M typ. In operation 100 Sleep mode 4 100 VBB=44V, ID=1mA 0.18 ID=3A 0.95 IF=3A 250 When Clock Duty = 50% VDD0.25 VDD0.75 1 1 Clock, Reset, CW/CCW, Sync 50 1 M1, M2 0 1.5 Normal-operation current control 2 VDD Output OFF (sleep) 10 1.25 IMOL=1.5mA VDD1.25 IMOH=1.5mA 3 3 10 0.95 1.00 1.05 When VREF = 1V in Mode F 100 98.1 95.7 92.4 88.2 83.1 77.3 70.7 63.4 55.5 47.1 38.2 29 19.5 9.8 . VSENSE=100%, VREF=0.1 to 1.0V VREF = . 2.0 ClockOutON 1.5 ClockOutOFF 1.8 Mode 1 to F 12 Mode 8 to F 9 Mode 4 to 7 7 Mode 1 to 3 When Clock Duty = 50% VDD0.25 VDD0.75 1 1 Clock, Reset, CW/CCW, Sync 50 1 M1, M2 0 1.5 Normal-operation current control 2 VDD Output OFF (sleep) 10 1.25 IMOL=1.5mA VDD1.25 IMOH=1.5mA 3 3 10 0.95 1.00 1.05 When VREF = 1V in Mode F 100 98.1 95.7 92.4 88.2 83.1 77.3 70.7 63.4 55.5 47.1 38.2 29 19.5 9.8 . VSENSE=100%, VREF=0.1 to 1.0V VREF= . 2.0 ClockOutON 1.5 ClockOutOFF 1.8 Mode 1 to F 12 Mode 8 to F 9 Mode 4 to 7 7 Mode 1 to 3 Unit mA
min.
max. 15
Main Supply Current Logic Supply Current Output MOSFET Breakdown Voltage Output MOSFET ON Resistance Output MOSFET Diode Forward Voltage Maximum Clock Frequency Logic Input Voltage
A
mA V V kHz V
REF Input Voltage REF Input Current Mo Output Voltage Mo Output Current Sense Terminal Inflow Current Sense Voltage
A
V mA
A
V
s s s s
* The direction in which current flows out of the product is regarded as negative.
108
ICs
SLA7060M/SLA7061M/SLA7062M
Pin Assignment
Pin No. 1 2
21
Symbol OutA OutA/ SenseA VDD REF Reset CW/CCW Clock GND M2 M1 MO Sync VBB SenseB OutB/ OutB Phase A output Phase A output
Function
MO
M1
M2
14 13 12
9 10
16 Reg
18
19 20
3 4 5 6
MIC
PreDriver Sequencer & Sleep Circuit
Phase A current sense Logic supply Control current setting & output OFF control input Internal logic reset input Normal/reverse control input Step Clock input Device GND Excitation mode setting input 2-phase excitation state monitor output PWM control signal input Driver supply (motor supply) Phase B current sense Phase B output Phase B output
PreDriver
7 8 9 10
DAC
+
11 12 13
17
OSC
14 15 16 17 18 19 20 21
SenseB
CA
VDD=3.0~5.5V
Disable Q1 Reset CW/CCW CB Clock R1 C1
* VDD line noise precaution: The device may malfunction if the VDD line noise exceeds 0.5V. As a countermeasure, separating the VDD system GND (S-GND) and VBB system GND (P-GND) from the device GND (Pin-11) helps to reduce noise. * Be sure to connect the unused logic input terminals (CW/CCW, M1, M2, Reset, Sync) to VDD or GND. Otherwise, the device will malfunction.
OutA/
OutB/
OutA
OutB
VBB
6 8 9 10 12 13 14 15 7
16
18
19
20
21
Microcomputer, M1 etc. MO
M2 Sync
SLA7060M Series
5
SenseA
11
17
SenseB
REF
R3
R2
RsA
RsB
GND
S-GND
P-GND
Component Values (Typical) . 2 Rs=0.1 to 2 (Power dissipation should be: P= .IO Rs) R1=10k CA=100F/50V R2=5.1k (VR) CB=10F/10V R3=10k C1=0.1F
(Unit : mm)
31.00.2
3.20.153.8
4.80.2 1.70.1
3.20.153.8
4.80.2 1.70.1
30.5 [Measured at the tip] [4.6] 1.60.5 [Measured at the tip]
12.90.2
3.20.15
17.90.6 50.5
9.90.2
2.450.2 [Measured at the root] 4 [R1] R-end
12.90.2
9.90.2
160.2 [Heatsink]
3.20.15
160.2 [Heatsink]
4.2MIN
0.65 0.1 20P1.430.5=28.61 [Measured at the tip] 31.30.2 [Including the resin burr]
+0.2
0.55 0.1
+0.2
60.6 7.50.6
1 2
3 4
5 6
7 8
11 13 15 17 19 21 10 12 14 16 18 20
0.65 0.1
+0.2
0.55 0.1
+0.2
ICs
109
SLA7075MR, MPR/7076MR, MPR/7077MR, MPR/7078MR, MPR 2-Phase/4 W1-2 Phase Excitation Support, Built-in Sequencer
Features
Lineup of built-in current sense resistor and built-in protection circuit-type Power supply voltages, VBB: 46 V (max), 10 to 44 V normal operating range Logic supply voltages, VDD: 3.0 to 5.5 V Maximum output currents: 1 A, 1.5 A, 2 A, and 3A Built-in sequencer Self-excitation PWM current control with fixed off-time Synchronous PWM chopping function prevents motor noise in Hold mode Sleep mode for reducing the IC input current in stand-by state ZIP type 23-pin molded package (SLA package)
46 46 6 *1
0.3 to VDD+0.3 0.3 to VDD+0.3
2 4.7 17 +150
20 to +85 30 to +150
V V V A V V V W C C C
Vref=0.4V, Mode F
*1: Output current value may be limited for the SLA7075MR, MPR (1.0 A), SLA7076MR, MPR (1.5 A), SLA7077MR, MPR (2.0 A), and SA7078MR, MPR (3.0 A), depending on the duty ratio, ambient temperature, and heating conditions. Do not exceed junction temperature of Tj under any circumstances.
Electrical Characteristics
Parameter Main Supply Current Logic Supply Current Output MOSFET Breakdown Voltage Output MOSFET ON Resistance Symbol IBB IBBS Icc V(BR)DSS RDS(ON) 100 0.7 0.45 0.25 0.18 0.85 1.0 0.95 0.95 250 0.25VDD 0.75VDD 1 1 0.04 0.04 0.04 0.04 2 10 VREF 100 2.0 1.5 0.305 0.305 0.205 0.155 0.7 2.3 3.5 4.6 0.3 0.45 0.4 0.45 VDD 0.85 0.6 0.4 0.24 1.1 1.25 1.2 2.1 min. Ratings typ. max. 15 100 5 Unit mA A mA V In operation Sleep 1 and Sleep 2 modes VBB=44V, ID=1mA SLA7075M, ID=1.0A SLA7076M, ID=1.5A SLA7077M, ID=2.0A SLA7078M, ID=3.0A SLA7075M, ID=1.0A SLA7076M, ID=1.5A SLA7077M, ID=2.0A SLA7078M, ID=3.0A When Clock Duty = 50% Conditions
Output MOSFET Diode Forward Voltage Maximum Clock Frequency Logic Input Voltage Logic Input Current
VF
V kHz V A
Fclock VIL VIH IIL IIH VREF VREFS IREF VSENSE TSE tcon tcoff RS
REF Input Current SENSE Sense Voltage Sleep-Enable Recovery Time Switching Time
Sense Resistance
Overcurrent Sense Voltage Overcurrent Sense Current Flag Output Voltage Flag Output Current
Vocp Iocp VFlagL VFlagH IFlagL IFlagH ModeF ModeE ModeD ModeC ModeB ModeA Mode9 Mode8 Mode7 Mode6 Mode5 Mode4 Mode3 Mode2 Mode1 VMOL VMOH IMOL IMOH ton(min) toff1 toff2 toff3
VDD1.25 1.25 1.25 100 98.1 95.7 92.4 88.2 83.1 77.3 70.7 63.4 55.5 47.1 38.2 29.0 19.5 9.8 VDD1.25 1.25 1.25 1.7 12 9 7
When step reference current ratio is 100% Sleep1&Sleep2 Clock Out ON Clock Out OFF SLA7075MR/7075MPR, tolerance of 3% SLA7076MR/7076MPR, tolerance of 3% SLA7077MR/7077MPR, tolerance of 3% SLA7078MR/7078MPR, tolerance of 3% SLA7075MPR/7076MPR/7077MPR/7078MPR, when motor coil shorts out SLA7075MPR/7076MPR SLA7077MPR SLA7078MPR SLA70750MPR/7076MPR/7077MPR/7078MPR, IFlagL=1.25mA SLA7075MPR/7076MPR/7077MPR/7078MPR, IFlagH=-1.25mA SLA7075MPR/7076MPR/7077MPR/7078MPR
Mo (Load) Output Voltage Mo (Load) Output Current PWM Minimum ON Time PWM OFF Time
IMOL=1.25mA IMOH=1.25mA
110
ICs
Pin Assignment
Pin No. Symbol OutA OutA/ SenseA MO M1 M2 M3 Clock VBB Gnd Ref/Sleep1 VDD Reset CW/CCW Sync Flag*1 SenseB OutB/ OutB Step Clock input Driver supply (motor supply) Device GND Control current mode/Sleep 1 setting input Logic supply Internal logic reset input Normal/reverse control input PWM control signal input Protection circuit monitor output*1 Phase B current sense Phase B current output Phase B current output Excitation mode/Sleep 2 setting input Phase A output Phase A output Phase A current sense 2 phase excitation state output monitor output Function
14
15
18
9 16 10 15
11
20 21 22 23
MIC
PreDriver Sequencer & Sleep Circuit
Reg
PreDriver
Protect
Protect
DAC
DAC
+
SenseA
PWM Control
PWM Control
RS
OSC
OSC
17 Sync
12 Gnd
The protect circuit is deleted and the flag pin is N.C. for SLA7075MR, 7076MR, 7077MR, and 7078MR.
Vcc=3.0V to 5.5V r1 Q1 CB
12.90.2
160.2
OutA OutA C1 VDD Reset/Sleep1 Clock CW/CCW M1 M2 M3 Sync MO Flag Ref/Sleep SenseA
BB
OutB OutB
9.90.2
R-end
0.65 0.1
Gnd SenseB
+0.2
(4.3)
0.55 0.1
0.7
+0.2
r2
r3
C2 One-point Gnd
Forming No.
Power Gnd
No.2151
Logic Gnd
9.5 0.5
Microcomputer, etc.
50.5
+1
Synchro Control
19
SenseB
RS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Reset
Clock
OutA
OutA
OutA
OutA
OutB
OutB
OutB
OutB
Flag
VDD
VBB
MO
M1
M2
M3
4.80.2 1.70.1
+ CA
3.20.15
ICs
111
Electrical Characteristics
Parameter Main Supply Current Logic Supply Current Charge Pump Voltage Output Breakdown Voltage Output MOS FET ON Resistance (total of the upper and lower values) Output MOS FET Diode Forward Voltage Logic Input Voltage Logic Input Current Maximum Clock Frequency PFD Input Current RC Terminal Inflow Current PFD Input Voltage Sense Voltage REF Input Voltage REF Input Current PWM OFF Time Thermal Protection Circuit Activation Temperature Hysteresis of Thermal Protection Circuit Activation Temperature Switching Time Symbol IBB Icc VB VO RDS (on) VSD VIL VIH IIL IIH Fclock IPFD IRC VPFDS VPFDM VPFDF VRs VREF IREF TOFF Tj Tj TONC TOFFC 0 10 1.1RtCt 150 10 2.5 2 VREF0.2 VCC 1.7 0.7 10 200 VCC 1.3 0.3 VCC0.75 1 1 100 36 0.8 1.5 VCC0.25 VBB+5 Ratings min. typ. max. 20 10
(Ta=25C, VBB=24V, VCC=5V, unless otherwise specified) Unit mA mA V V V V V IDS=3A ISD=3A Remarks
A A
kHz
Excluding Ena
A A
V V V V V Slow Decay Mixed Decay Fast Decay Steady-state
A s
C C
s s
ClockOut ClockOut
112
ICs
SLA7611M
CP2 15
VB 18
VBB 9
1 2 3 4 5
Charge Pump
OUT Block Clock 13 CW/CCW 12 F/H Ena Reset Sequence 14 Logic 8 7 Level shift & Pri-Driver
6 7 8 9 10 11 12 13 14 15
REF
PWM Control
Current Control
+ _
5 PFD
4 RC
10 GND
16 17 18
C2 16 3 CB
+
C1
10 to 30V 9 VBB
+
5V C4 C3
15 CP2
18 VB
CA
C5
VCC CP1
13 12
Microcomputer, etc.
11
14 8 7 R4 R2
SLA7611M
OUTV 17 1
3 SPM
REF PFD 5 4
RC 10
GND
Rs Ct R1 R5 R3 S-GND P-GND Rt
(Unit : mm)
3.20.15
3.20.153.8
16 0.2
13 0.2
9.9 0.2
2.450.2
6.70.5 (3) 9.7 0.5
+1
0.65 0.1
+0.2
+0.2
+0.2
Other lead forming shapes are also available. For details, contact our sales representative.
1 2 3 . . . . . . . . 18
Forming No.
No.871
ICs
113
*: Insert a 5V Zener diode between VCC1 and VMC3 when using with VCC1 of 35 V or more.
Electrical Characteristics
Parameter Main Supply Current Logic Supply Current Logic Input Voltage Logic Input Current ENA Input Current REF Input Current SENCE Voltage SENCE Current MO Output Voltage RC Pin Threshold Voltage RC Pin Outflow Current Charge Pump Output Voltage High Side Output Voltage (between gate sources) Low Side Output Voltage Maximum CL Frequency Maximum Input CL Width (on) Power-on Reset time Output Delay Time CW/CCW, F/H Input Data Setup Time CW/CCW, F/H Input Data Hold Time Symbol min. ICC1 ICC2 VIL VIH IIL IIH IENA IREF VSENCE ISENCE VMOL VMOH VRCL VRCH IRC VMC3 VHGSL VHGSH VLGL VLGH fck TCON PTW TIO TICS TICH 500 500 100 1 1.5 2 7.5 8.5 1 4 0.5 1.5 300 VCC1+9 1 20 3.75 20 20 100 20 1 20 1 20 20 20 20 Ratings typ. max. 25 10 1.25
(Ta=25C, Vcc1=24V, VCC2=5V, unless otherwise specified) Unit mA mA V V A A A A V A V V V V A V V V V V KHz s s s s s Against CL Without Zener diode VRC=0V VIL=0V VIH=5.5V VENA=0V VREF=0 to 5.5V VREF=1V VSENCE=0V, 2V IMOL=1mA IMOH=1mA Conditions
114
ICs
SI-7510
Oscillator
Charge Pump
3 4
OHGA OHSA OHGB OHSB OHGC OHSC OHGD OHSD OHGE OHSE
Enable MO CL
5 6 7 8 9 10 11 12 13 14 15 16 17
Lowside Drive
PWM Control
18 19 20
24V
21
IO=VRS/RS IOM=Io/2 *IOM : Motor Coil Current tOFF=1.1*Rt*Ct
5V
VCC2 MC1 MC2 MC3 VCC1
R3
Enable MO
7 8 9 10 11
4 30 29 28 27 26 25 24 23 22 21
22 23 24 25 26 27 28 29
OHGA OHSA OHGB OHSB OHGC OHSC OHGD OHSD OHGE OHSE
4 5 10 15 3 9 1 7 14 SLA5073 8 12 13 2 6 11
SI-7510
C4 R1Ref C3 R2
12 13
20 19 18
4 3 9 7 17 16 15
Gnd OLD OLE
Pins 11 to 15: NC
SLA5074
1 8
10
2 6
14
Sense
RC
Rs
Io
Ct
Rt
R1=510 R2=100(VR) R3=20K RS=0.33(1 to 2W) Rt=15 to 75K Ct=420 to 1100pF C1=2200pF C2=0.01F C3=0.1F C4=0.01F
30
Truth Table
Pin Name Clock CW/CCW Forward Rotation (CW) 4-phase excitation Disable Enable Low Level High Level Positive Edge Backward Rotation (CCW) 4-5 phase excitation Enable Reset
*Be especially careful of noise on the Vcc line. The product may malfunction if noise on the Vcc line is 0.5 V or more.
(Unit : mm)
OHA OHB OHC OHD OHE OLA OLB OLC OLD OLE MO Reset CW, Full CCW, Full CCW, Half CW, Half
28.20.3
75 CL Reset
80
85
90
95
100
105
110
3.610.1
4.30.3
CW/CCW F/H OHA OHB OHC OHD OHE OLA OLB OLC OLD OLE MO CW, Half Disable Reset CCW,Full Disable The range to Prohibit Switching The range to Prohibit Switching 500ns 500ns Switchable Range CW/CCW F/H CL
1.0 0.06
+ 0.3
7.10.5
Enable
10.16
1.778
2.80.2
ICs
115
STA6940M
Features
Output current: 4A (peak: 8A) Power supply voltage: VBB = 10 to 40V Logic supply voltage: VDD = 3.0 to 5.5V Built-in UVLO, OCP, and TSD protection Built-in diag output function STA 18-pin package
100s or less
DC control (Ta = 25C) PWM control (Ta = 25C) at Slow Decay PWM control (Ta = 25C) at Fast Decay
*: Output current value may be limited, depending on the duty ratio, ambient temperature, and heating conditions. Do not exceed junction temperature of Tj under any circumstances.
Main Supply Voltage Output Current Logic Supply Voltage PWM REF Input Voltage OCP REF Input Voltage Case Temperature
min. 10 3.0
Unit
Conditions
V A V V V C
When operating current control When operating overcurrent control Rear center (without Fin)
Electrical Characteristics
Parameter Main Supply Current Logic Supply Current Charge Pump Voltage Charge Pump Oscillation Frequency Low Driver Supply Voltage Protection Voltage Low Logic Supply Voltage Protection Voltage Low Charge Pump Voltage Protection Voltage Output MOSFET Breakdown Voltage Output MOSFET ON Resistance Output MOSFET Diode Forward Voltage Logic Input Voltage Logic Input Current Maximum Logic Input Clock Frequency PWM REF Input Voltage PWM REF Input Current OCP REF Input Voltage OCP REF Input Current PWM Sense Voltage Overcurrent Sense Voltage Sense Input Current Diag Output Voltage Diag Output Current Diag Output Frequency PWM Minimum ON Time PWM OFF Time OCP Minimum ON Time OCP OFF Time Crossover Current Delay Time Switching Time Thermal Protection Activation Temperature Thermal Protection Deactivation Temperature Symbol IBB IDD Vcp Fcp VUVBL VUVBH VUVDL VUVDH VUVCL VUVCH V(BR)DS RDS(ON) VF VLIL VLIH ILIL ILIH fclk VPREF IPREF VOREF IOREF VPSEN VOSEN ISENSE VLOL VLOH ILOL ILOH fDIAG tpon(min) tPOFF toon(min) tOOFF tCOCD tcon tcoff Ttsdon Ttsdoff min. Ratings typ. max. 20 5 Unit mA mA V kHz V V V V V V V
VBB+5 360 7 7.8 2.3 2.5 3.8 4 60 0.1 0.95 0.75VDD 1 1 100 0.1 10 0.1 VPREF 0.045 VOREF 0.045 10 VPREF 0.015 VOREF 0.015 20 2 VPREF +0.015 VOREF +0.015 1.25 VDD1.25 1.25 1.25 90 5 35 5 142 150 3 2.7 140 115 750 1 0.13 2.1 0.25VDD
V V V
A A
kHz V
A
V
A
duty=50% When controlling the current VREF=0 to VDD When controlling the current VREF=0 to VDD
V V
A
V V mA mA kHz
s s s s
ILOL=1.25mA ILOL=1.25mA VLOL=1.25V VLOH=VDD-1.25 During PWM operation During OCP operation
ns
s s
C C
116
ICs
STA6940M
Pin Assignment
Pin No. 1 2,3 4 5 6 7 8 9 10 11 12 13 14 15 16,17 18 Symbol VBB OA Sense 1 IN1 IN2 VDD PWM_REF OCP_REF Gnd Diag CP2 CP1 CP Sense 2 OB VBB Function Main supply Output terminal A Constant current sense terminal Output setting terminal Logic supply Constant current setting input terminal Overcurrent setting input terminal Device Gnd Monitor terminal Capacitor connection terminal for charge pump Overcurrent sense terminal Output terminal B Driver supply
OA OA OB OB
OCP_REF
Comp
10 GND
15 Sense2
4 Sense1
Lot No
(90.2)
Type No
3.30.5
(1)
(6.9)
R-end
(4-
R1
)
0.45 +0.2 0.1 2.540.5 (Measured at the tip)
17xP1.270.5=21.591 (Measured at the tip) C1.50.5 25.55 (Including the resin burr)
(3.6)
ICs
117
SPI-6631M
Features
Power supply voltages, VBB: 13 V to 33 V Signal power supply configuration Output current Iout: 3 A (max)... repetitive current (normal-operation current) Built-in current recirculation diode Built-in UVLO, TSD and OCP protection Built-in dead time function that prevents through current upon phase switching Built-in error sense flag output HSOP16-pin package
DutyCycle=100%*
*: Output current value may be limited, depending on the duty ratio, ambient temperature, and heating conditions. Do not exceed the rated current or maximum junction temperature (Tj = 150C).
Electrical Characteristics
Parameter Main Supply Voltage Main Supply Current Maximum Clock Pulse Width Input Voltage Input Current Crossover Dead Time VB Terminal Breakdown Voltage VB-OUT Breakdown Voltage VB Terminal Current Output Leakage Current MOSFET ON Resistance MOSFET Diode Forward Voltage Overcurrent Sense Current Overcurrent Protection Blank Time Overcurrent Protection Delay Time Thermal Protection Operation Temperature Thermal Protection Hysteresis Low Voltage Protection Operation Voltage Low Voltage Protection Hysteresis Alarm Output Voltage Symbol VBB IBB tw VIL VIH IIL IIH Tdelay VB VB-OUT IB IDSS RDS(ON) VSD IOCP tblank tocp TJ TJ UVLO UVLO VAlarm min. 13 2.0 100 800 7 0.7 0.5 4.0 0.4 Ratings typ. 8 20 500 VBB+5 5 0.4 1.2 1 170 15 4.5 0.45 max. 33 23 3 0.8 1200 3 800 0.7 2.2 4 2.2 5.0 0.5 0.5 Unit V mA s V V A A ns V V mA A A
VIN(0), VIN=0.8V VIN(1), VIN=2.0V Breakdown voltage between VB and GND VB-OUT=5V VOUT=VBB=35V VOUT=0V IOUT=-1A, Between VBB and OUTIOUT=1A, Between OUT and S ISD=1A Short between Out and Out
V A s ms C C V V V
118
ICs
SPI-6631M
Pin Assignment
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Symbol CP2 CP1 OUTU S OUTV OUTW Alarm GND INLW INHW INLV INHV VBB INLU INHU VB Function Capacitor terminal for charge pump 2 Capacitor terminal for charge pump 1 DMOSFET phase U output Sense terminal (lower arm source output) DMOSFET phase V output DMOSFET phase W output Alarm output Ground Phase W lower arm input Phase W upper arm input Phase V lower arm input Phase V upper arm input Driver supply terminal Phase U lower arm input Phase U upper arm input Capacitor terminal for charging up charge pump
(Unit : mm)
1 1.27
2.50 0.05
0.25 0.05
+0.15
2.75MAX
10.50 0.30
7.50 0.20
4.30
ICs
119
SX68000M Series Surface-Mount, Built-in Overcurrent Protection, Thermal Shutdown, and Overcurrent Limiting Circuits
Features
A package of 6 MOSFET units for 3-phase bridge and pre-drive (HVIC, LVIC) Best for driving the fan motor (built-in motor) of air conditioner, etc. Built-in boot diode with limited resistance Built-in undervoltage lock out (UVLO) circuit Built-in overcurrent protection circuit (OCP) Built-in Thermal Shut Down (TSD) function Built-in current limiter function (OCL) Error (FO) terminal with shutdown input function 7.5V regulator output function (35mA max.)
(Ta=25C) Conditions Vcc=15V,VIN=0V Between VCC and COM Between VB and HS (U, V, W) PW100s, duty=1% Ta=25 All element operation All element operation
*1: When mounted on a board (1.6 mm, 35m copper layer, CEM-3, moldless, natural air cooling)
Electrical Characteristics
Parameter Control Supply Current Boot Supply Current Input Voltage Input Voltage Hysteresis Width Input Current Undervoltage Lock Out (high side) Undervoltage Lock Out (low side) FO Terminal Output Voltage OCL Output Voltage Current Limiter Reference Voltage Overcurrent Protection Trip Voltage Overcurrent Protection Retention Time OCP Blanking Time SD Terminal Blanking Time Thermal Protection and Release Threshold Regulator Output Voltage MOSFET Output Breakdown Voltage MOSFET Output Leakage Current Symbol Icc Ibs VIH VIL VH IIH VUVHL VUVHH VUVLL VUVLH VFOL VFOH VOCLL VOCLH VLIM VTRIP tp tbk(ocp) tbk(ocl) TDH TDL TDhys VREG VDSS IDSS min. 1.0 9.0 9.5 10.0 10.5 4.8 4.5 0.6175 0.9 20 135 105 6.75 250 SX68001M typ. 4.6 140 2.0 1.5 0.5 230 0.65 1.0 25 2 3.3 150 120 30 7.5 1.25 1.1 1.0 70 60 800 45 75 720 40 750 55 70 660 20 max. 7.4 280 2.5 500 11.0 11.5 12.0 12.5 0.5 0.5 5.5 0.6825 1.1 165 135 8.25 100 1.5 1.5 10 1.3 min. 1.0 9.0 9.5 10.0 10.5 4.8 4.5 0.6175 0.9 20 135 105 6.75 500 Ratings SX68002M typ. 4.6 140 2.0 1.5 0.5 230 0.65 1.0 25 2 3.3 150 120 30 7.5 3.2 1.0 1.0 70 60 810 60 120 815 40 760 60 110 750 30 max. 7.4 280 2.5 500 11.0 11.5 12.0 12.5 0.5 0.5 5.5 0.6825 1.1 165 135 8.25 100 4.0 1.5 10 1.3 min. 1.0 9.0 9.5 10.0 10.5 4.8 4.5 0.6175 0.9 20 135 105 6.75 500 SX68003M typ. 4.6 140 2.0 1.5 0.5 230 0.65 1.0 25 2 3.3 150 120 30 7.5 2.0 1.0 1.0 70 60 940 100 135 975 45 900 105 135 905 35 Unit max. 7.4 280 2.5 500 11.0 11.5 12.0 12.5 0.5 0.5 5.5 0.6825 1.1 165 135 8.25 100 2.4 1.5 10 1.3 mA A V V A V Vcc=15V V V V V V s s s C V V Vcc=15V, VFO=5V, RFO=10k Vcc=15V Vcc=15V Vcc=15V Vcc=15V Vcc=15V Vcc=15V Vcc=15V Condotions Vcc1,2=15V VB HS=15V Vcc=15V, Output:ON Vcc=15V, Output:OFF Vcc=15V Vcc=15V, VIN=5V
(Ta=25C)
A
V
MOSFET DC ON Resistance RDS ON Diode Forward Voltage Boot Diode Leakage Current Boot Diode Forward Voltage Boot Diode Reverse Recovery Time Boot Diode Series Resistance VSD IIB VFB trr RB td(on) tr trr td(off) tf td(on) tr trr td(off) tf
A V ns
IREG=35mA Vcc=15V, ID=100A, VIN=0V Vcc=15V, VDS=500V(250 V forSX68001M), VIN=0V Vcc=15V, ID=1A(0.75 A for SX68002M or 1.25 A for SX68003M), VIN=5V Vcc=15V, ISD=1A(0.75 A for SX68002M or 1.25 A for SX68003M), VIN=0V VR=500V(250 V for SX68001M) IF=0.15A IF/IRP=100mA/100mA
ns V DC =300V(150V for SX68001M), Vcc=15V, ID=1A(0.75 A for SX68002M or 1.25 A for SX68003M), HIN=0 to 5V Inductive load ns
120
ICs
SX68000M Series
HIN1 HIN2 HIN3 COM1 SD VCC2 REG LIN1 LIN2 LIN3 COM2 REG
Input Logic
VB2
VB32
VB31
VBB1 VBB2 UVLO Control IC HIN1 HIN2 HIN3 COM1 SD VCC2 REG LIN1 LIN2 LIN3 5V COM2 FO OCL Thermal Shutdown OCP OCP & OCL LS REG UVLO Input Logic (OCP reset) Input Logic UVLO UVLO UVLO
BLDCM
(Unit : mm)
1 1.20.2
17 1.050.2
2.1 0.2
14.1 0.3
ICs
121
(Ta=25C)
Conditions
jc ja
Top Tch Tstg
Electrical Characteristics
Ratings Parameter Control Supply Current Input Voltage Input Voltage Hysteresis Width Input Current Undevoltage Lock Out (high side) Undevoltage Lock Out (low side) FO Pin Output Voltage Overheat detection threshold Overheat detection release threshold Regulator output voltage Boot Diode Forward Voltage Boot Diode Series Resistance MOSFET Output Withstand Voltage MOSFET Output Leakage Current MOSFET DC On Resistance Diode Forward Voltage Symbol min. Icc VIH VIL VIhys IIH IIL VUVHL VUVHH VUVhys VUVLL VUVLH VUVhys VFOL VFOH TDH TDL VREG VFBD RBD VDSS IDSS RDS(ON) VSD td(on) tr High Side Switching Time trr td(off) tf td(on) tr Low Side Switching Time trr td(off) tf 1 9.0 9.5 10.0 10.5 0 4.0 135 105 6.75 250 SMA6821MP/SLA6826M typ. 4 2 1.5 0.5 50 10.0 10.5 0.5 11.0 11.5 0.5 150 120 7.5 1.1 22 1.4 1.0 450 100 90 350 20 550 110 90 360 20 max. 6 2.5 100 2 11.0 11.5 12.0 12.5 1.0 5.5 165 135 8.25 1.3 100 1.8 1.5 min. 1 9.0 9.5 10.0 10.5 0 4.0 135 105 6.75 500 SMA6822MP/SLA6827M typ. 4 2 1.5 0.5 50 10.0 10.5 0.5 11.0 11.5 0.5 150 120 7.5 1.1 22 3.6 1.0 550 100 120 420 30 570 100 120 450 30 max. 6 2.5 100 2 11.0 11.5 12.0 12.5 1.0 5.5 165 135 8.25 1.3 100 4.0 1.5 1 9.0 9.5 10.0 10.5 0 4.0 135 105 6.75 500 SMA6823MP/SLA6828M min. typ. 4 2 1.5 0.5 50 10.0 10.5 0.5 11.0 11.5 0.5 150 120 7.5 1.1 22 2.0 1.0 640 100 150 520 30 650 100 150 580 30 max. 6 2.5 100 2 11.0 11.5 12.0 12.5 1.0 5.5 165 135 8.25 1.3 100 2.4 1.5 ns ns V C V V V A V Vcc=15V, ID=100A, VIN=0V Vcc=15V Vcc=15V IREG=35mA IF=0.15A V Between VCC and COM V mA V V A Vcc=15V Vcc=15V, Output:ON Vcc=15V, Output:OFF Vcc=15V Vcc=15V, VIN=5V Vcc=15V, VIN=0V Between VB and U (V, W) Unit Conditions
(Ta=25C)
Vcc=15V, VDS=500V (250V for SMA6821MP/SLA6826M), VIN=0V Vcc=15V, ID=1.0A (0.75A for SMA6822MP/SLA6827M, 1.25A for SMA6823MP/SLA6828M), VIN=5V Vcc=15V, ID=1.0A (0.75A for SMA6822MP/SLA6827M, 1.25A for SMA6823MP/SLA6828M), VIN=0V
VBB=300V (150V for SMA6821M/SLA6826M), Vcc=15V, I D =2A (1.5A for SMA6822M/ SLA6827M, 2.5A for SMA6823M/SLA6828M), 0VVIN5V Inductive load
122
ICs
4 11 10
3 5
VB1
VB2
VB3
HO2 HS2 HIN1 HIN2 HIN3 COM3 HO3 12 HS3 14 13
VD VBB1 VCC1 UVLO HIN1 HIN2 HIN3 COM1 U V W1 W2 Input Logic UVLO UVLO UVLO VBB2
9 8 7 6
HVIC
23 VCC2
LO1
MCU
18 16
22 21
FO COM2
LVIC
15V
The input pulldown resistor is built into an IC (about 100 k). If the input is expected to be unstable or fluctuate widely, however, it needs to be reinforced with an external resistor. Attach capacitors near IC. Attach a ceramic capacitor in parallel with the electrolytic capacitor if too much noise is generated.
(Unit : mm)
310.2
Gate burr
40.2
JAPAN
(Measured at the root)
Lot No.
50.5
JAPAN
Lot No.
10.20.2
Part No.
1.20.1
(Measured at the root)
Part No.
R-end
(Measured at the tip)
23 X P1.270.5=29.210.6
(Measured at the tip)
4-( R1
(4.5)
31.30.2
(Including the resin burr)
1 2
3 4
5 6
7 8
11 13 15 17 19 21 23 10 12 14 16 18 20 22 24
Forming No.2451
310.2 24.40.2 16.40.2 Gate burr 3.20.15
160.2
12.90.2
16.40.2
50.5
3.20.15
4-(R1)
(10.5)
12.90.2
160.2
R-end
23 X P1.270.7=29.211
(4.5)
2 1 3
4 5
6 7
8 9
10 11
12 13
14 15
16 17
18 19
20
Forming No.2171
Forming No.2175
0.50.1
(4.4)
0.6 0.1
+0.2
9.90.1
ICs
123
SMA6850M Series
Features
Built-in boot diode with limiting resistor Supports CMOS (3.3 and 5.0 V) input levels Built-in undervoltage lock out circuit Built-in thermal sensor (non-stop, Fo output) Built-in regulator output (7.5 V/35 mA) Current detection using 3 shunt resistors
Symbol
VDSS VCC VBS Io Iop IREG VIN PD
SMA6854M
600
Unit
V V V A A mA V W CW C/W C C C
Conditions
VCC=15V, ID=100uA, VIN=0V Between VCC and COM Between VB and HS (U, V, W) PW100s, duty=1%
j-c j-a
Top Tj Tstg
Electrical Characteristics
Ratings Parameter Control Supply Current Input Voltage Input Voltage Hysteresis Width Input Current Symbol min. ICC VIH VIL VIhys IIH IIL VUVHL Undervoltage Lock Out VUVHH VUVhys VUVLL Undervoltage Lock Out VUVLH VUVhys FO Pin Output Voltage Thermal Protection and Release Threshold Regulator Output Voltage Boot Diode Leakage Current Boot Diode Forward Voltage Boot Diode Series Resistance MOSFET Output Breakdown Voltage MOSFET Output Leakage Current MOSFET DC On Resistance MOSFET Diode Forward Voltage VFOL VFOH TDH TDL TDHYS VREG ILBD VFBD RBD VDSS IDSS RDS (ON) VSD td(on) tr High Side Switching Time trr td(off) tf td(on) tr Low Side Switching Time trr td(off) tf 1.0 9.0 9.5 10.0 10.5 0 4.0 135 105 6.75 500 SMA6853M typ. 4 2.0 1.5 0.5 50 10.0 10.5 0.5 11.0 11.5 0.5 150 120 30 7.5 1.1 22 2.0 1.0 640 100 150 520 30 650 100 150 580 30 max. 6 2.5 100 2 11.0 11.5 12.0 12.5 1.0 5.5 165 135 8.25 10 1.3 100 2.4 1.5 min. 1.0 9.0 9.5 10.0 10.5 0 4.0 135 105 6.75 600 SMA6854M typ. 4 2.0 1.5 0.5 50 10.0 10.5 0.5 11.0 11.5 0.5 150 120 30 7.5 1.1 60 2.8 1.0 530 55 125 510 50 530 60 125 540 55 max. 6 2.5 100 2 11.0 11.5 12.0 12.5 1.0 5.5 165 135 8.25 10 1.3 100 3.5 1.5 ns ns VBB=300V, VCC=15V, I D=2.5A V A V V A V VCC=15V, I D=100uA, VIN=0V IREG=35mA C VCC=15V, No FIN V V V Hysteresis Between VCC and COM Hysteresis VCC=15V mA V V A VCC=15V, IREG=0A VCC=15V, Output:ON VCC=15V, Output:OFF VCC=15V VCC=15V, V IN=5V VCC=15V, V IN=0V Between VB and U (V, W) Unit Conditions
(Ta=25C)
VCC=15V, V DS=500V (600V for the SMA6854M), V IN=0V VCC=15V, I D=1.25A (0.75A for the SMA6854M), V IN=5V VCC=15V, I SD=1.25A (0.75A for the SMA6854M), V IN=0 V
124
ICs
SMA6850M Series
VCC1(4)
Input Logic
VCC2(23) VREG(16) LIN1(20) LIN2(19) LIN3(18) COM2(21) FO(22) Thermal Detect 7.5V Reg. UVLO Input Logic Low Side Driver
8 7 6 5
23
VCC2
LO1 17
MCU
20 19 18 16
LO2 13
LO3 VREG 15
22 21
FO COM2
LVIC
15V
(Unit : mm)
40.2
Gate burr
10.20.2
JAPAN
(Measured at the root)
Lot No.
50.5
JAPAN
Part No.
Lot No.
Part No.
R-end
(Measured at the tip)
4-(
R1
(4.5)
1 2
3 4
5 6
7 8
11 13 15 17 19 21 23 10 12 14 16 18 20 22 24
Forming No.2451
ICs
125
SMA6860M Series
Features
Built-in boot diode with 210- limiting resistor Built-in overcurrent protection circuit (OCP) Overcurrent protection with off-time period adjustable by an external capacitor Overcurrent limiting operation Built-in thermal shutdown (TSD) circuit Externally controllable shutdown operation
1.5 2.25
2.5 3.75
Electrical Characteristics
Parameter Control Supply Current Boot Supply Current Input Voltage Undervoltage Lock Out Symbol Icc IB VIH VIL UVHL UVHH UVhys UVLL UVLH UVhys TDH TDL TDHYS VTRIP VLIM tp ILBD VFBD Trrb Rb VDSS IDSS min. 1.6 9.0 9.5 10.0 10.5 120 100 0.9 0.5035 500 SMA6862M typ. 4.2 135 2.9 2.1 10.0 10.5 0.5 11.0 11.5 0.5 135 115 20 1.0 0.53 2 1.0 70 210 3.6 1.0 720 40 110 670 20 600 40 120 555 20 max. 7 380 3.4 11.0 11.5 12.0 12.5 150 130 1.1 0.5565 10 1.3 100 4.0 1.5 min. 1.6 9.0 9.5 10.0 10.5 120 100 0.9 0.5035 500 Ratings SMA6863M typ. 4.2 135 2.9 2.1 10.0 10.5 0.5 11.0 11.5 0.5 135 115 20 1.0 0.53 2 1.0 70 210 2.0 1.0 790 60 115 725 20 680 70 120 605 20 max. 7 380 3.4 11.0 11.5 12.0 12.5 150 130 1.1 0.5565 10 1.3 100 2.4 1.5 min. 1.6 9.0 9.5 10.0 10.5 120 100 0.9 0.5035 500 SMA6865M typ. 4.2 135 2.9 2.1 10.0 10.5 0.5 11.0 11.5 0.5 135 115 20 1.0 0.53 2 0.8 70 210 1.4 1.0 750 60 100 680 20 640 65 100 560 20 Unit max. 7 380 3.4 11.0 11.5 12.0 12.5 150 130 1.1 0.5565 10 1.3 100 1.7 1.5 mA uA V V Conditions Vcc=15V VB=15V, HIN=5V, VCC=15V Between VB and U (V, W) Hysteresis V Between VCC and COM Hysteresis V V ms A V ns V A V VCC=15V
(Ta=25C)
Termal Protection and Release Threshold Overcurrent Protection Trip Voltage Current Limiting Reference Voltage Overcurrent Protection Retention Time Boot Diode Leakage Current Boot Diode Forward Voltage Boot Diode Reverse Recovery Time Boot Diode Series Resistance MOSFET Output Breakdown Voltage MOSFET Output Leakage Current
VCC=15V VCC=15V VRC=5V, RR=360k, CC=0.0047F VR=500V IF=0.05A IF/IRP100mA/100mA VCC=15V, ID=100uA, VIN=0V VCC=15V, VDS=500V, VIN=0V VCC=15V, ID=1.25A (0.75A for the SMA6862M), VIN=5V VCC=15V, ID=1.25A (0.75A for the SMA6862M), VIN=0V
td(on) r High Side Switching Time rr td(off) f td(on) r Low Side Switching Time rr td(off) f
ns VBB=300V, VCC=15V, ID=1.5A (2.5A for the SMA6863M and SMA6865M), VIN=0 to 5V Inductive load ns
126
ICs
SMA6860M Series
(Unit : mm)
40.2
Gate burr
10.20.2
JAPAN
(Measured at the root)
Lot No.
50.5
JAPAN
Part No.
Lot No.
Part No.
R-end
(Measured at the tip)
4-(
R1
(4.5)
1 2
3 4
5 6
7 8
11 13 15 17 19 21 23 10 12 14 16 18 20 22 24
Forming No.2451
ICs
127
SLA6860M Series
Features
Built-in boot diode with 210- limiting resistor Built-in overcurrent protection circuit (OCP) Overcurrent protection with off-time period adjustable by an external capacitor Overcurrent limiting operation Built-in thermal shutdown (TSD) circuit Externally controllable shutdown operation
2.0 3
3.0 4.5
V VCC=15V, ID=100uA, VIN=0V V Between VCC and COM V Between VB and HS (U, V, W) A A PW100s, duty=1% V HIN1 to HIN3, LIN1 to LIN3 W TC=25 /W All elements operating
Electrical Characteristics
Parameter Control Supply Current Boot Supply Current Input Voltage Undervoltage Lock Out Symbol ICC IB VIH VIL UVHL UVHH UVhys UVLL UVLH UVhys TDH TDL TDHYS VTRIP VLIM tp ILBD VFBD Trrb Rb VDSS IDSS min. 1.6 9.0 9.5 10.0 10.5 120 100 0.9 0.5035 250 SLA6866M typ. 4.2 135 2.9 2.1 10.0 10.5 0.5 11.0 11.5 0.5 135 115 20 1.0 0.53 2 1.0 70 210 1.25 1.1 665 20 45 580 10 520 20 40 480 15 max. 7 380 3.4 11.0 11.5 12.0 12.5 150 130 1.1 0.5565 10 1.3 100 1.5 1.5 min. 1.6 9.0 9.5 10.0 10.5 120 100 0.9 0.5035 500 Ratings SLA6868M typ. 4.2 135 2.9 2.1 10.0 10.5 0.5 11.0 11.5 0.5 135 115 20 1.0 0.53 2 1.0 70 210 2.0 1.0 790 60 115 725 20 680 70 120 605 20 max. 7 380 3.4 11.0 11.5 12.0 12.5 150 130 1.1 0.5565 10 1.3 100 2.4 1.5 min. 1.6 9.0 9.5 10.0 10.5 120 100 0.9 0.5035 500 SLA6870M typ. 4.2 135 2.9 2.1 10.0 10.5 0.5 11.0 11.5 0.5 135 115 20 1.0 0.53 2 0.8 70 210 1.4 1.0 755 65 100 680 15 645 70 105 560 20 Unit max. 7 380 3.4 11.0 11.5 12.0 12.5 150 130 1.1 0.5565 10 1.3 100 1.7 1.5 mA uA V V Conditions VCC=15V VB=15V, HIN=5V, VCC=15V Between VB and U (V, W) Hysteresis V Between VCC and COM Hysteresis V V ms A V ns V A V VCC=15V
(Ta=25C)
Undervoltage Lock Out Thermal Protection and Release Threshold Overcurrent Protection Trip Voltage Current Limiting Reference Voltage Overcurrent Protection Retention Time Boot Diode Leakage Current Boot Diode Forward Voltage Boot Diode Reverse Recovery Time Boot Diode Series Resistance MOSFET Output Breakdown Voltage MOSFET Output Leakage Current
VCC=15V VCC=15V VRC=5V, RR=360k, CC=0.0047uF VR=500V (250V for the SMA6866M) IF=0.05A IF/IRP100mA/100mA VCC=15V, ID=100uA, VIN=0V VCC=15V, VDS=500V (250V for the SLA6866M), VIN=0V VCC=15V, ID=1.0A (1.25A for the SLA6868M, and 1.5A for the SLA6870M),V IN=5V VCC=15V, ID=1.0A (1.25A for the SLA6868M, and 1.5A for the SLA6870M), V IN=0V
td(on) r High Side Switching Time rr td(off) f td(on) r Low Side Switching Time rr td(off) f
ns VBB=300V (150V for the SLA6866M), VCC=15V, ID=2.0A (2.5A for the SLA6868M, and 3.0A for the SLA6870M), VIN=0 to 5V Inductive load ns
128
ICs
SLA6860M Series
(Unit : mm)
12.90.2
3.20.15
50.5
12.90.2
160.2
2.20.6
(10.5)
4-(R1) R-end
9.90.1
2.450.1
(4.5)
2.20.6
23xP1.270.2=29.210.5
0.50.1
0.6 0.1
+0.2
(4.4)
30.3
Forming No.2171
Forming No.2175
ICs
129
SLA6805MP
Features
A package including 6 units each of IGBT and FRD for 3-phase bridge, and pre-drive (HVIC, LVIC) Best for driving a refrigerator compressors and dishwashing driers High side drive of bootstrap method has been employed. Built-in undervoltage lock out (auto regression) Built-in overcurrent protection circuit Built-in fail signal output function (for when the overcurrent protection circuit activates)
(Ta=25C)
jc
Top Tch Tstg
Electrical Characteristics
Parameter Control Supply Current Input Voltage Input Voltage Hysteresis Width Input Current Undervoltage Lock Out (High Side) Undervoltage Lock Out (Low Side) FO Pin Output Voltage Overcurrent Protection Trip Voltage Blanking Time IGBT Output Breakdown Voltage IGBT Output Leakage Current IGBT Output Saturation Voltage Diode Forward Voltage Symbol Icc VIH VIL VIhys IIH IIL VUVHL VUVHH VUVhys VUVLL VUVLH VUVhys VFOL VFOH VTRIP tbk VCES ICES VCE(sat) VEC td(on) tr High Side Switching Time trr td(off) tf td(on) tr Low Side Switching Time trr td(off) tf Ratings min. 1 9.0 9.5 10.0 10.5 0 4.0 0.45 600 typ. 4 2 1.5 0.5 50 10.0 10.5 0.5 11.0 11.5 0.5 0.5 2 1.75 1.65 365 55 80 365 170 395 60 75 395 170 max. 6 2.5 100 2 11.0 11.5 12.0 12.5 1.0 5.5 0.55 1 2.1 2 ns VBB=300V, Vcc=15V, Ic=3A, VIN=0 to 5V, inductive load ns V V us V mA V V Vcc=15V Vcc=15V Vcc=15V Vcc=15V, Ic=1mA, VIN=0V V Between VCC and COM V Between VB and U (V, W) Unit mA V V A Vcc=15V Vcc=15V, Output:ON Vcc=15V, Output:OFF Vcc=15V Vcc=15V, VIN=5V Vcc=15V, VIN=0V Conditions
(Ta=25C)
130
ICs
SLA6805MP
2 VB1 5 VCC1
3 VB2
4 VB3
11 10 +
HO1 HS1 1
The input pulldown resistor is built in IC (about 100 k). However, if the input is expected to be unstable or very fluctuant, it needs to be reinforced with external resistor.
DC 300V +
9 8 7 6 HU HV HW
HO3
0.1uF
Attach capacitors near IC. Attach a ceramic capacitor in parallel with the electrolytic capacitor if too much noise is generated.
HVIC
23 VCC2
14
LO1
Controller
RC 20 19 18 16
LU LV LW
LO2 17 RS
LO3 RCIN 15
CC
22 21
FO COM2
LVIC
RS
Gate burr
3.20.15 x 3.8
2.20.7 (Measured at the tip)
4.80.2 1.70.1
12.90.2
160.2
3.20.15
9.90.2
160.2
50.5
12.90.2
9.50.2
2 (R')
8.70.5
R-end
8.7 +1 0.5
(3.7)
(4.4)
0.50.1
0.6
+0.15 0.05
0.60.1
11 13 15 17 19 21 23 10 12 14 16 18 20 22
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
ICs
131
SLA6845M Supports 3 Shunt, IGBT Output Element, Built-in Thermal Sensor and 7.5 V Regulator
Features
A package including 6 units each of IGBT and FRD for 3-phase bridge, and pre-drive (HVIC, LVIC) Best for driving a washing machine drying fan motor High side drive of bootstrap method has been employed. Built-in undervoltage lock out circuit (auto regression) Built-in thermal sensor (non-stop) Built-in fail signal output function (when operating the thermal sensor and undervoltage lock out circuit) Support for 3-shunt current sense Built-in 7.5 V regulator output (35mA max.)
(Ta=25C)
Tc=25C, all IGBT elements in operation All IGBT elements in operation All FRD elements in operation
Electrical Characteristics
Parameter Control Supply Current Input Voltage Input Voltage Hysteresis Width Input Current Symbol Icc VIH VIL VIhys IIH IIL VUVHL VUVHH VUVhys VUVLL VUVLH VUVhys VFOL VFOH TDH TDL TDhys VREG VCES ICES VCE(sat) VF trr td(on) tr td(off) tf td(on) tr td(off) tf min. 1 9.0 9.5 10.0 10.5 0 4.0 135 105 6.75 600 Ratings typ. 4 2 1.5 0.5 50 10.0 10.5 0.5 11.0 11.5 0.5 150 120 30 7.5 1.75 1.65 50 315 50 375 165 325 60 400 165 max. 6 2.5 100 2 11.0 11.5 12.0 12.5 1.0 5.5 165 135 8.25 1 2.1 2.0 Unit mA V V Conditions Vcc=15V, VIN=5V Vcc=15V, Output:ON Vcc=15V, Output:OFF Vcc=15V Vcc=15V, VIN5V Vcc=15V, VIN=0V Between VB and U (V, W) Hystersis V Between VCC and COM Hystersis Vcc=15V, IFO=1mA Vcc=15V, IFO=1.6mA Vcc=15V, No Fin, IREG=0mA IREG=35mA Vcc=15V, Ic=1mA, VIN=0V Vcc=15V, VCE=600V, VIN=0V Vcc=15V, Ic=3A, VIN=5V Vcc=15V, IF=3A, VIN=0V IF=3A, di/dt=100A/s
(Ta=25C)
A
V
V C V V mA V V ns
Thermal Protection and Release Threshold Regulator Output Voltage IGBT Output Breakdown Voltage IGBT Output Leakage Current IGBT Output Saturation Voltage Diode Forward Voltage Diode Reverse Recovery Time
132
ICs
SLA6845M
11 10
+ 1
HO2
+ 13 M
VB1
VB2
VB3
9
VBB1 VCC1 UVLO HIN1 HIN2 HIN3 COM1 U V W1 7.5V Reg. Terminal Detect W2 UVLO UVLO UVLO VBB2
8 7 6
+ 12 14 Cs
Input Logic
23
VCC2
LO1 24
VCC2 VREG
Controller
20 19 18
LO2 17
UVLO
Input Logic
LO3 15
COM2 FO
22 21
FO COM2 RS LVIC
+ 15V
The input pulldown resistor is built into the IC (about 100 k ). However, if the input is expected to be unstable or to fluctuate greatly, it needs to be reinforced using an external resistor. Attach capacitors near the IC. Attach a ceramic capacitor in parallel with the electrolytic capacitor if too much noise is generated.
(Unit : mm)
310.2 24.40.2 4.80.2 3.20.15 X 3.8 1.70.1
JAPAN
12.90.2
9.90.2
9.90.2
12.90.2
160.2
3.20.15
50.5
2.450.2 (Measured at the root)
50.5
Lot No.
12.90.2
160.2
2.20.6
9.90.1
(10.5)
R-end
2.450.1
R-end
(4.5)
(3)
2.20.6
23xP1.270.2=29.210.5
0.50.1
0.6 0.1
+0.2
(4.4)
30.3
4 3 5
6 7
8 9
10 11
12 13
14 15
16 17
18 19
20 21
22 23
24
2 1 3
4 5
6 7
8 9
10 11
12 13
14 15
16 17
18 19
20 21
22 23
24
9.50.5
4-(R1)
4-(R1)
ICs
133
SCM1100M Series IGBT Output Element, Built-in Shoot Through Prevention and Overcurrent Protection Circuits
Features
Each half-bridge circuit consists of a pre-driver circuit that is completely independent from the others Protection against simultaneous high- and low-side turning on Bootstrap diodes with series resistors for suppressing inrush current are incorporated CMOS compatible input (3.3 to 5 V) Designed to minimize simultaneous current through both high- and low-side IGBTs by optimizing gate drive resistors UVLO protection with auto restart Overcurrent protection with off-time period adjustable by an external capacitor Fault (FO indicator) signal output at protection activation: UVLO (low side only), OCP, and STP Proprietary power DIP package UL Recognized Component (File No.: E118037)
T aa 25 (T =25)
Conditions Between VBB and LS1 to LS3 Between VBB and LS1 to LS3 VCC=15V,IC=1mA,VIN=0V VCC1 to 3 and COM1 to COM3 VB1 to VB3 and HS (U,V,W) T1ms HIN1 to HIN3 or LIN1 to LIN3 and COM1 to COM3 FO1 to FO3 and COM1 to COM3 Tc=25C while one IGBT element operates Per IGBT element Per FRD element
Supply Voltage VBB Supply Voltage (Surge) VDC(Surge) IGBT Output Withstand Voltage VCES Control Supply Voltage VCC Control Supply Voltage (Bootstrap) VBS Output Current (continuous) Io Output Current (pulse) Iop Input Voltage VIN FO Pin Voltage VFO Power Dissipation PD Thermal Resistance (IGBT) R(j-c)Q Thermal Resistance (FRD) R(j-c)F Operating Case Temperature TOP Junction Temperature Tj Storage Temperature Tstg Insulation Withstand Voltage Viso
134
ICs
SCM1100M Series
Electrical Characteristics
Parameter Control Supply Current Bootstrap Supply Current Input Voltage Input Voltage Hysteresis Width Input Current Undervoltage Lock Out (high side) Undervoltage Lock Out (low side) FO Pin Output Voltage Overcurrent Protection Trip Voltage Overcurrent Protection Hold Time Blanking Time IGBT Output Breakdown Voltage IGBT Output Leakage Current IGBT Output Saturation Voltage Boot Diode Forward Voltage Boot Diode Leakage Current Boot Diode Forward Voltage Boot Diode Recovery Time Boot Diode Series Resistance Symbol ICC Ibs VIH VIL VH IIH IIL VUVHL VUVHH VUVLL VUVLH VFOL VFOH VTRIP tP tbk VCES ICES VCE(sat) VF IIB VFB trr RB td(on) tr trr td(off) tf td(on) tr trr td(off) tf SCM1101M/SCM1101MF min. typ. max. 5 8 400 800 2 2.5 1 1.5 0.5 50 100 2 10 12 10.5 12.5 10.5 12.5 11 13 0.5 4.8 0.46 0.5 0.54 2 2 600 1 1.75 2.2 1.7 2.2 10 1.1 1.3 70 22 320 50 80 560 210 350 80 140 610 200 min. 1 10 10.5 10.5 11 4.8 0.46 2 600 Ratings SCM1103M typ. 5 400 2 1.5 0.5 50 0.5 2 1.7 1.4 1.1 70 22 340 60 80 430 240 380 90 100 500 220 max. 8 800 2.5 100 2 12 12.5 12.5 13 0.5 0.54 1 2.1 2 10 1.3 SCM1104M/SCM1104MF min. typ. max. 5 8 400 800 2 2.5 1 1.5 0.5 50 100 2 10 12 10.5 12.5 10.5 12.5 11 13 0.5 4.8 0.46 0.5 0.54 2 2 600 1 1.75 2.2 1.6 2.2 10 1.1 1.3 70 22 360 70 80 560 210 420 110 140 630 210 Unit mA uA V Conditions VCC=15V, 3 circuits total VB-HS=15V, 1 circuit VCC=15V, Output:ON VCC=15V, Output:OFF VCC=15V VCC=15V, VIN=5V VCC=15V, VIN=0V
(Ta=25)
VCC=15V
V V ms s V mA V V A V ns
VCC=15V,VFO=5V RFO=10k VCC=15V VCC=15V, CFO=2.2nF VCC=15V VCC=15V, IC=1mA, VIN=0V VCC=15V, VCE=600V, VIN=0V VCC=15V, IC=rated output current (continuous) VIN=5V VCC=15V, IF=rated output current (continuous), VIN=0V VR=600V IF=0.15A IF/IRP=100mA/100mA
(Ta=25)
Parameter Control Supply Current Bootstrap Supply Current Input Voltage Input Voltage Hysteresis Width Input Current Undervoltage Lock Out (high side) Undervoltage Lock Out (low side) FO Pin Output Voltage Overcurrent Protection Trip Voltage Overcurrent Protection Hold Time Blanking Time IGBT Output Breakdown Voltage IGBT Output Leakage Current IGBT Output Saturation Voltage Boot Diode Forward Voltage Boot Diode Leakage Current Boot Diode Forward Voltage Boot Diode Recovery Time Boot Diode Series Resistance Symbol ICC Ibs VIH VIL VH IIH IIL VUVHL VUVHH VUVLL VUVLH VFOL VFOH VTRIP tP tbk VCES ICES VCE(sat) VF IIB VFB trr RB td(on) tr trr td(off) tf td(on) tr trr td(off) tf min. 1 10 10.5 10.5 11 4.8 0.46 2 600 SCM1105MF typ. 5 400 2 1.5 0.5 50 0.5 2 1.75 1.75 1.1 70 22 365 80 90 690 200 415 135 115 790 205 Ratings SCM1106M/SCM1106MF min. typ. max. 5 8 400 800 2 2.5 1 1.5 0.5 50 100 2 10 12 10.5 12.5 10.5 12.5 11 13 0.5 4.8 0.46 0.5 0.54 2 2 600 1 2.2 2.6 1.7 2.2 10 1.1 1.3 70 22 320 50 80 490 80 350 80 140 540 80 SCM1110MF typ. 5 400 2 1.5 0.5 50 0.5 2 2.2 1.75 1.1 70 22 365 80 90 650 85 415 135 115 755 85 Unit max. 8 800 2.5 100 2 12 12.5 12.5 13 0.5 0.54 1 2.6 2.2 10 1.3 mA uA V Conditions VCC=15V, 3 circuits total VB-HS=15V, 1 circuit VCC=15V, Output:ON VCC=15V, Output:OFF VCC=15V VCC=15V, VIN=5V VCC=15V, VIN=0V VCC=15V
2
12 12.5 12.5 13 0.5 0.54 1 2.2 2.2 10 1.3
V V ms s V mA V V A V ns
VCC=15V, VFO=5V RFO=10k VCC=15V VCC=15V,CFO=2.2nF VCC=15V VCC=15V, IC=1mA, VIN=0V VCC=15V, VCE=600V, VIN=0V VCC=15V, IC=rated output current (continuous) VIN=5V VCC=15V, IF=rated output current (continuous), VIN=0V VR=600V IF=0.15A IF/IRP=100mA/100mA
ICs
135
HS VB
VB
VBB
VCC
HO
HIN LIN
Drive Corcuit
HS
U,V,W
COM FO CFO
COM FO CFO
Drive Corcuit
LO
LS
LS
HVIC
8 7 CBOOT 6 VCC HIN LIN Input Logic & Shoot Through Prevention VB UV Detect Level Shift HO Drive Circuit 32 HS UV Detect O.C. Protect 31
5 3
The input pulldown resistor is built in IC (about 100 k). However, if the input is expected to be unstable or very fluctuant, it needs to be reinforced with external resistor. Attach capacitors near IC. Attach a ceramic capacitor in parallel with the electrolytic capacitor if too much noise is generated.
4 1 2 16 15 CBOOT 14 13
Controller
COM FO CFO
28 VB UV Detect Input Logic & Shoot Through Prevention Level Shift Drive Circuit 29 HS UV Detect O.C. Protect M
HO
11
COM FO CFO
25 VB VCC HIN LIN Input Logic & Shoot Through Prevention UV Detect Level Shift Drive Circuit 26 HS UV Detect O.C. Protect HO
COM FO CFO
VBB
CFO
136
ICs
SCM1100M Series
(Unit : mm)
Root
Root
(lead center)
(lead center)
JAPAN
Part No.
Lot No.
JAPAN
Part No.
Lot No.
(lead center)
(lead center)
A lead cross-section (S=9) D lead cross-section (S=9) (Size after solder dip)
A lead cross-section (S=9) D lead cross-section (S=9) (Size after solder dip)
3.450.5
C 8P5.1=40.8
3.60.5
4.40.3 3.450.5
3.450.5
470.3
MAX1.2
1.20.2
C 8P5.1=40.8
3.60.5
A A
2 (5)
+0.5 0
Root
(lead center)
470.3
1.20.2
17.250.5
12.250.5
MAX1.2
Root
17.250.5
B B
(5)
15.950.5
(lead center)
3.20.15
15.950.5
11.450.5
190.3
3.20.15
11.450.5
12.250.5
190.3
3.450.5 (9.05)
43.30.3 2.080.2 5P1.27=6.35 5P1.27=6.35 2.57 1.27 3.7 1.27 3.7 3.24 1.27 3.7 5P1.27=6.35
B B
(5)
5P1.27=6.35
3.450.5 (9.05)
3.450.5
1.27
3.7
0.5 -0.1
+0.2 -0.1
0.5 -0.1
+0.2
0.6 -0.1
+0.2
3.450.5
+0.2
3.60.5
0.5 -0.1
+0.2
(0.65)
(0.6)
0.5
+0.2 -0.1
+0.2 -0.1
0.6 -0.1
+0.2
(11.6)
0.5 -0.1
0.5 -0.1
+0.2
(0.65)
0.7 -0.1
+0.2
1.2 -0.1
+0.2
(0.6)
0.7 -0.1
0.5
Enlarged view of A
Enlarged view of B
0.5
0.5
0.5 -0.1
+0.2
+0.2 -0.1
1.2 -0.1
+0.2
0.5
0.5
Enlarged view of A
Enlarged view of B
ICs
137
SCM1200M Series IGBT Output Element, Built-in Thermal Shutdown, Overcurrent Protection, and Shoot Through Prevention Circuits
Features
Six IGBTs and six FRDs for the 3-phase bridge, a pre-drive IC, and a boot diode are integrated into a single package Ideal for driving air conditioner compressors, washing machine drums, and refrigerator compressors Built-in shoot through prevention (STP) circuit (when the ON signal is input simultaneously) All IGBTs can be shut down when commonly connected to the FO pin. Three built-in bootstrap diodes Supports CMOS (3.3 and 5 V) input levels Built-in undervoltage lock out (UVLO) circuit (auto regression) Built-in overcurrent protection (OCP) circuit Built-in thermal shut down (TSD) circuit (auto regression) Fail signal output during operation of the UVLO (low side only), OCP, or STP circuit
T a 25 (T a =25)
Conditions Between VBB and LS1 to LS3 Between VBB and LS1 to LS3 VCC=15V,IC=1mA,VIN=0V Between VCC and COM Between VB and HS (U, V, W) Tc=25 PW<1ms HIN,LIN,OCP Between FO and COM TC=25, per IGBT element Per IGBT element Per FWD element
Supply Voltage VDC Supply Voltage (Surge) VDC(Surge) IGBT Output Breakdown Voltage VCES Control Supply Voltage VCC Control Supply Voltage (Bootstrap) VBS Output Current (continuous) Io Output Current (pulse) Iop Input Voltage VIN FO Pin Voltage VFO Collector Dissipation PD Thermal Resistance R(j-c)Q (Junction to Case) R(j-c)F Operating Case Temperature COP Junction Temperature (Power part) Tj Storage Temperature Tstg Insulation Breakdown Voltage Viso
138
ICs
SCM1200M Series
Electrical Characteristics
Parameter Control Supply Current Boot Supply Current Input Voltage Input Voltage Hysteresis Width Input Current Undervoltage Lock Out (high side) Undervoltage Lock Out (low side) FO Pin Output Voltage Overcurrent Protection Trip Voltage Overcurrent Protection Retention Time Blanking Time Thermal Protection and Release Threshold IGBT Output Breakdown Voltage IGBT Output Leakage Current IGBT Output Saturation Voltage Diode Forward Voltage Boot Diode Leakage Current Boot Diode Forward Voltage Boot Diode Recovery Time Boot Diode Series Resistance Symbol ICC Ibs VIH VIL VHYS IIH IIL VUVHL VUVHH VUVLL VUVLH VFOL VFOH VTRIP tP tbk TDH TDL TDHYS VCES ICES VCE(sat) VF IIB VFB trr RB SCM1221M/SCM1221MF min. typ. max. 6 140 2.0 2.5 1.0 1.5 0.5 230 500 2 10.0 11.0 12.0 10.5 11.5 12.5 10.0 11.0 12.0 10.5 11.5 12.5 0.5 4.8 0.46 0.50 0.54 20 25 1.65 135 150 165 105 120 135 30 600 1 1.75 2.2 1.7 2.2 10 1.1 1.3 70 22.0 min. 1.0 10.0 10.5 10.0 10.5 4.8 0.46 20 135 105 600 Ratings SCM1223M typ. 6 140 2.0 1.5 0.5 230 11.0 11.5 11.0 11.5 0.50 25 1.65 150 120 30 1.7 1.4 1.1 70 22.0 max. 2.5 500 2 12.0 12.5 12.0 12.5 0.5 0.54 165 135 1 2.1 2.0 10 1.3 SCM1224M/SCM1224MF min. typ. max. 6 140 2.0 2.5 1.0 1.5 0.5 230 500 2 10.0 11.0 12.0 10.5 11.5 12.5 10.0 11.0 12.0 10.5 11.5 12.5 0.5 4.8 0.46 0.50 0.54 20 25 1.65 135 150 165 105 120 135 30 600 1 1.75 2.2 1.6 2.2 10 1.1 1.3 70 22.0 Unit mA A V A Conditions VCC=15V, 3 circuits total VB-HS=15V, 1 circuit VCC=15V, Output:ON VCC=15V, Output:OFF VCC=15V VCC=15V, VIN=5V VCC=15V, VIN=0V
(Ta=25)
VCC=15V
V V s s V mA V V A V ns
VCC=15V,VFO=5V RFO=10k VCC=15V VCC=15V VCC=15V VCC=15V VCC=15V, IC=1mA, VIN=0V VCC=15V, VCE=600V, VIN=0V VCC=15V, IC=Rating of Output Current (Continuous), V IN=5V VCC=15V, IF=Rating of Output Current (Continuous), V IN=0V VR=600V IF=0.15A IF/IRP=100mA/100mA
(Ta=25)
Parameter Control Supply Current Boot Supply Current Input Voltage Input Voltage Hysteresis Width Input Current Undervoltage Lock Out (high side) Undervoltage Lock Out (low side) FO Pin Output Voltage Overcurrent Protection Trip Voltage Overcurrent Protection Retention Time Blanking Time Thermal Protection and Release Threshold IGBT Output Breakdown Voltage IGBT Output Leakage Current IGBT Output Saturation Voltage Diode Forward Voltage Boot Diode Leakage Current Boot Diode Forward Voltage Boot Diode Recovery Time Boot Diode Series Resistance Symbol ICC Ibs VIH VIL VHYS IIH IIL VUVHL VUVHH VUVLL VUVLH VFOL VFOH VTRIP tP tbk TDH TDL TDHYS VCES ICES VCE(sat) VF IIB VFB trr RB min. 1.0 10.0 10.5 10.0 10.5 4.8 0.46 20 135 105 600 SCM1225MF typ. 6 140 2.0 1.5 0.5 230 11.0 11.5 11.0 11.5 0.50 25 1.65 150 120 30 1.75 1.75 1.1 70 22.0 Ratings SCM1226M/SCM1226MF min. typ. max. 6 140 2.0 2.5 1.0 1.5 0.5 230 500 10.0 10.5 10.0 10.5 4.8 0.46 20 135 105 600 11.0 11.5 11.0 11.5 0.50 25 1.65 150 120 30 2.2 1.7 1.1 70 22.0 2 12.0 12.5 12.0 12.5 0.5 0.54 165 135 1 2.6 2.2 10 1.3 SCM1230MF typ. 6 140 2.0 1.5 0.5 230 11.0 11.5 11.0 11.5 0.50 25 1.65 150 120 30 2.2 1.75 1.1 70 22.0 Unit max. 2.5 500 2 12.0 12.5 12.0 12.5 0.5 0.54 165 135 1 2.6 2.2 10 1.3 mA A V A Conditions VCC=15V, 3 circuits total VB-HS=15V, 1 circuit VCC=15V, Output:ON VCC=15V, Output:OFF VCC=15V VCC=15V, VIN=5V VCC=15V, VIN=0V VCC=15V
min. 1.0 10.0 10.5 10.0 10.5 4.8 0.46 20 135 105 600
2
12.0 12.5 12.0 12.5 0.5 0.54 165 135 1 2.2 2.2 10 1.3
V V s s V mA V V A V ns
VCC=15V, VFO=5V RFO=10k VCC=15V VCC=15V VCC=15V VCC=15V VCC=15V, IC=1mA, VIN=0V VCC=15V, VCE=600V, VIN=0V VCC=15V, IC=Rating of Output Current (Continuous), V IN=5V VCC=15V, IF=Rating of Output Current (Continuous), VIN=0V VR=600V IF=0.15A IF/IRP=100mA/100mA
ICs
139
HS VB
Db Rb
VBB
VB VCC HIN LIN COM
UV UV Detect Detect Input Logic & Shoot Through Prevention Level Shift Drive Circuit
HO
HS
U,V,W
FO
Drive Circuit
RS
LD
OCP
O.C. Protect
Thermal Detect
LS HVIC
HS1 VB1 Rb Db
VCC VB
HO
U
HS
The input pulldown resistor is built in IC (about 100 k). However, if the input is expected to be unstable or very fluctuant, it needs to be reinforced with external resistor. Attach capacitors near IC. Attach a ceramic capacitor in parallel with the electrolytic capacitor if too much noise is generated.
Drive Circuit LD
RS
O.C. Protect
Thermal Detect
LS1
HVIC
Rb
VB VCC
HO
V
HS
Controller
Drive Circuit LD
RS
O.C. Protect
Thermal Detect
LS2
HVIC
Rb
VBB
VB
VCC
HO
W
HS
Drive Circuit LD
RS
CS
O.C. Protect
Thermal Detect
LS3 HVIC
Co
Ro
RS
140
ICs
SCM1200M Series
(Unit : mm)
Root
Root
(lead center)
(lead center)
JAPAN
Part No.
Lot No.
JAPAN
Part No.
Lot No.
(lead center)
(lead center)
A lead cross-section (S=9) D lead cross-section (S=9) (Size after solder dip)
A lead cross-section (S=9) D lead cross-section (S=9) (Size after solder dip)
3.450.5
C 8P5.1=40.8
3.60.5
4.40.3 3.450.5
3.450.5
470.3
MAX1.2
1.20.2
C 8P5.1=40.8
3.60.5
A A
2 (5)
+0.5 0
Root
(lead center)
470.3
1.20.2
17.250.5
12.250.5
MAX1.2
Root
17.250.5
B B
(5)
15.950.5
(lead center)
3.20.15
15.950.5
11.450.5
190.3
3.20.15
11.450.5
12.250.5
190.3
3.450.5 (9.05)
43.30.3 2.080.2 5P1.27=6.35 5P1.27=6.35 2.57 1.27 3.7 1.27 3.7 3.24 1.27 3.7 5P1.27=6.35
B B
(5)
5P1.27=6.35
3.450.5 (9.05)
3.450.5
1.27
3.7
0.5 -0.1
+0.2 -0.1
0.5 -0.1
+0.2
0.6 -0.1
+0.2
3.450.5
+0.2
3.60.5
0.5 -0.1
+0.2
(0.65)
(0.6)
0.5
+0.2 -0.1
+0.2 -0.1
0.6 -0.1
+0.2
(11.6)
0.5 -0.1
0.5 -0.1
+0.2
(0.65)
0.7 -0.1
+0.2
1.2 -0.1
+0.2
(0.6)
0.7 -0.1
0.5
Enlarged view of A
Enlarged view of B
0.5
0.5
0.5 -0.1
+0.2
+0.2 -0.1
1.2 -0.1
+0.2
0.5
0.5
Enlarged view of A
Enlarged view of B
ICs
141
Output current IO: Two types available: 0.5 A (LC5205D) and 1 A (LC5210D) Self-excitation PWM current control method Undervoltage lockout (UVLO) Overcurrent protection (OCP) Thermal shutdown (TSD) DIP-8 type mold package Supports driving without input electrolytic capacitor Power factor correction (PFC) application circuit Triac dimmer control application circuit
Excluding when tw is less than 1 s Excluding when tw is less than 1 s When using a Sanken evaluation board
*1: The output current value may be limited depending on the duty ratio, ambient temperature, and heating conditions. Do not exceed the junction temperature Tj under any circumstances. *2: The power dissipation PD depends on the pattern layout of the circuit board used.
Applications
LED light bulbs LED lighting equipment
Electrical Characteristics
Ratings Parameter Symbol min. IBB Conditions IBBs Conditions VDS(BR) Conditions RDS(on) Conditions VF Conditions VReg Conditions IReg fclk Conditions VRef IRef VSen ISen Vocp Conditions VUVLOon Conditions VUVLOoff Conditions TTSD Conditions TTSDhys Conditions tBLK LC5205D typ. 2.0 During operation 0.8 When the output is off ID=1mA 3.5 ID=0.5A 0.8 ID=0.5A 12.0 IReg=0.1mA max. min. LC5210D typ. 2.0 During operation 0.8 When the output is off ID=1mA 1.7 ID=1.0A 0.88 ID=1.0A 12.0 IReg=0.1mA Unit max. mA 1.2 mA V V 12.5 V 2 200 duty=50% 0 VRef 30 10 VRef 10 3 At the Sen pin 14 At the VBB voltage 13 At the VBB voltage 150 Control IC chip temperature 55 Control IC chip temperature 400 1 VRef +30 0 VRef 30 10 VRef 10 3 At the Sen pin 14 At the VBB voltage 13 At the VBB voltage 150 Control IC chip temperature 55 Control IC chip temperature 400 duty=50% 1 VRef +30 kHz V A mV A V V V ns mA
1.2 450
Output MOSFET Breakdown Voltage Output MOSFET ON Resistance Output MOSFET Diode Forward Voltage Reg Output Voltage Reg Maximum Output Current Maximum Input Response Frequency REF Input Voltage REF Input Current Sense Voltage Sense Input Current Overcurrent Sense Voltage UVLO Release Voltage UVLO Operation Voltage TSD Operating Temperature TSD Temperature Hysteresis Blanking Time
450
11.5
12.5 2
11.5
200
142
ICs
LC5200 Series
(Unit : mm)
Pin Assignment
Pin No. 1 2 3 4 5 6 7 8 Symbol Reg PWM Ref Sen OUT VBB NC GND Function 12-V Reg output pin CR connection pin for setting PWM Reference voltage input pin for controlling PWM Load current sense pin Load output pin Main power supply pin Pin removed Device ground pin
1 1.0 -0.05
+0.3
7.50.5 3.40.1
3.30.2
4.20.3
6.50.2
0.25 +0.1
-0.05
0~15
0~15
Block Diagram
OUT
Ta-PD Characteristics
PWM
Control IC
ICs
143
*: Latch off is an operation in which protection is performed while oscillation is stopped. Avalanche energy capacity guaranteed by 2-chip structure, simplifying the surge absorption circuit
Applications
LED light bulbs LED lighting equipment
Lineup
Part Number LC5511D LC5513D LC5521D LC5523D LC5523F MOS FET VDSS(min.) RDS(ON) (max.) 3.95 1.9 3.95 1.9 Isolated/Non-isolated Non-isolated DIP8 Isolated Package POUT* 230 VAC/Universal 13W/10W 20W/16W 13W/10W 20W/16W 60W/40W
650V
T0220F-7L
*: The output power values in the table above are those at the rated temperature. Output at 120 to 140% of the rated temperature is possible for the maximum output power. Note, however, that the output power may be limited by a low output voltage and by the ON duty specified during transformer design.
Electrical Characteristics
Parameter Symbol min. Ratings typ. max. Unit Remarks
1.Control
Power Supply Startup Operation Operation Startup Voltage Operation Stop Voltage Circuit Current During Operation Startup Circuit Operation Voltage Startup Current Startup Current Supply Threshold Voltage 1 Startup Current Supply Threshold Voltage 2 Normal Operation Minimum Oscillation Frequency Maximum ON Time FB Pin Control Lower Voltage Maximum Feedback Current Leading Edge Blanking Time Quasi-Resonant Operation Threshold Voltage 1 Quasi-Resonant Operation Threshold Voltage 2 Protection Operation Overcurrent Detection Threshold Voltage OCP Pin Outflow Current OCP Pin OVP Operation Voltage OLP Threshold Voltage 1 OLP Threshold Voltage 2 OVP Pin Threshold Voltage Vcc Pin OVP Operation Voltage Thermal Shutdown Temperature Vcc(ON) Vcc(OFF) Icc(ON) VSTARTUP ICC(STARTUP) Vcc(BIAS)1 Vcc(BIAS)2 fosc TON(max.) VFB(min.) IFB(max.) TBW VBD(TH1) VBD(TH2) VOCP IOCP VBD(OVP) VFB(OLP)1 VFB(OLP)2 VOVP Vcc(OVP) Tj(TSD) 13.8 8.4 42 5.5 9.5 14.4 11.0 30.0 0.55 10 0.14 0.12 0.54 120 2.2 5.0 4.1 1.6 28.5 135 15.1 9.4 57 3.0 11.0 16.6 14.0 40.0 0.90 25 500 0.24 0.17 0.60 40 2.6 5.5 4.5 2.0 31.5 17.3 10.7 3.7 72 1.0 12.5 18.8 18.0 50.0 1.25 40 0.34 0.22 0.66 10 3.0 6.0 4.9 2.4 34.0 V V mA V mA V V kHz s V A ns V V V A V V V V V
2.MOSFET
Drain-Source Voltage Drain Leakage Current ON Resistance Switching Time Thermal Resistance VDSS IDSS RDS(ON) RDS(ON) tf tf ch-c ch-c ch-F 650 300 3.95 1.9 250 400 42 35.5 3.1 V A ns ns /W /W /W
LC5511D/LC5521D LC5513D/LC5523D, F LC5511D/LC5521D LC5513D/LC5523D, F Between channel and case for the LC5511D and LC5521D Between channel and case for the LC5513D and LC5523D Between channel and internal frame for the LC5523F
144
ICs
LC5500 Series
LC5521D/LC5523D/LC5523F
Pin No. LC5521D/LC5523D LC5523F 1 2 2 4 3 5 4 6 5 3 6 7 8 1 Pin Symbol S/GND VCC OCP FB NF(NC) OVP D/ST Function MOSFET source/GND for control Control circuit power input Overcurrent protection/Quasi-Resonant signal input Feedback signal input/overload protection signal input Overvoltage protection signal input MOSFET drain/startup current input
2.80.2
4.20.2 2.60.2
6.50.2
(14)
LC
a b
(1.1) 2.60.1
(Measured at the root)
1 1.0 -0.05
+0.3
7.6TYP
7.50.5 3.40.1 4.20.3
3.30.2
0.25 +0.1
20.15
5P1.170.15 =5.850.15
(Measured at the root)
13.50.5
7-0.620.15
2.8
1.3
-0.05
0~15
0~15
10.10.2
2 3 4 5 6 7
3.20.2
150.3
ICs
145
T aa 25 (T =25)
Conditions ID=100uA Between VCC and COM Between VB and VM1, VM2 Tc=25 PW100s, duty=1% EN, IN, FO TC=25, all elements operating All elements operating
Electrical Characteristics
Ratings Parameter Control Supply Current Boot Supply Current Input Voltage (EN, IN, FO) Input Current (EN, IN) Undervoltage Lock Out (VB) Undervoltage Lock Out (VCC) FO Pin Output Voltage Thermal Protection and Release Threshold Internal Dead Time MOSFET Output Breakdown Voltage MOSFET Output Leakage Current Symbol Icc IB VIH VIL IIH VUVHL VUVHH VUVLL VUVLH VFO(L) VFO(H) TDH TDL Tdead VDSS IDSS min. 1 9 9.5 10 10.5 0 3.6 135 105 250 SLA2601M typ. 2 135 2 1.5 230 150 120 430 0.11 1 1290 100 900 30 1270 80 880 30 max. 2.5 500 11 11.5 12 12.5 1 5 165 135 100 0.14 1.5 min. 1 9 9.5 10 10.5 0 3.6 135 105 250 SLA2602M typ. 2 135 2 1.5 230 150 120 430 0.14 1 1260 40 850 15 1240 40 830 25 Unit max. 2.5 500 11 11.5 12 12.5 1 5 165 135 100 0.185 1.5 mA uA V uA V V V ns V uA V ns Conditions Vcc=15V, FO=OPEN VB=15V Vcc=15V Vcc=15V Vcc=15V, EN,IN=5V Between VB and VM1, VM2 Between VCC and COM Vcc=15V, FO=OPEN Vcc=15V
(Ta=25)
MOSFET DC ON Resistance RDS(on) MOSFET Diode Forward Voltage VSD td(on) tr td(off) tf td(on) tr td(off) tf
Vcc=15V ID=100uA VDS=250V VCC=15V, ID=7A (3.5A for the SLA2602M),EN=5V ISD=7A (3.5A for the SLA2602M) VBB=200V, VCC=15V, ID=7A (3.5A for the SLA2602M), EN=5V, R load
ns
146
ICs
SLA2601M/SLA2602M
The input pull-down resistor is built in IC (about 22 k). However, if the input is expected to be unstable or to fluctuate greatly, it needs to be reinforced using an external resistor. Attach capacitors near the IC. Attach a ceramic capacitor in parallel with the electrolytic capacitor if too much noise is generated. When inserting a current sense resistor between LS1/LS2 and COM, make sure to specify the resistance so that the voltage between LS1/LS2 and COM is 1 V or less.
Pin Assignment
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Symbol LSI VM1 VM1 (LG1) (LG1) VBB1 VB1 (LG1) (LG1) EN IN COM COM VCC FO (LG2) (LG2) VB2 VBB2 (LG2) (LG2) VM2 VM2 LS2 Function MOSFET L1 source pin/MOSFET L2 source pin MOSFET H1 source pin/MOSFET L1 drain pin Same as above Cut pin (MOSFET L1 gate pin) Same as above MOSFET H1 drain pin/MOSFET H2 drain pin High side floating power supply pin 1 Cut pin (MOSFET L1 gate pin) Same as above Input pin for enabling output Input pin for switching output Pre-drive IC ground pin Same as above Pre-drive IC power supply pin Fo signal output pin Cut pin (MOSFET L2 gate drive pin) Same as above High side floating power supply pin 2 MOSFET H1 drain pin/MOSFET H2 drain pin Cut pin (L2 gate drive pin) Same as above MOSFET H2 source pin/MOSFET L2 source pin Same as above MOSFET L1 source pin/MOSFET L2 source pin
Truth Table
EN IN FO H1 H2 L1 L2
L X H H
X X H L
X H L L
(Unit : mm)
310.2
4.80.2 1.70.1
12.90.2
9.90.2
50.5
2MAX
MAX
(6.3)
A B
9.90.2
12.90.2
JAPAN
JAPAN
160.2
R-end
9.30.5
4-(R1)
R-end
30.5
2-(R1)
(4.5)
0.5 +0.15 -0.05 4.50.7 (Measured at the tip) 23 X P1.270.7=29.211 (Measured at the tip)
ICs
147
148
ICs
Transistors
Ordering Information & Standard Packing Quantities .............. 150 Application Note ............................................................................... 152 2-1 Transistors ............................................................................. 153 Selection Guide .................................................................... 153 VCEO -IC ............................................................................. 153 Audio Transistors ............................................................ 154 Switching Transistors ..................................................... 155 Specifications List by Part Number .................................. 156 2-2 MOS FETs .............................................................................. 163 Selection Guide .................................................................... 163 By VDSS ............................................................................ 163 Specifications List by Part Number .................................. 164 2-3 IGBT ........................................................................................ 167 Selection Guide .................................................................... 167 By VCES ............................................................................ 167 Specifications List by Part Number .................................. 168 2-4 Transistor and MOS FET Arrays ....................................... 170 Specifications List by Part Number .................................. 170 Specifications List by Application .................................... 172 Sink Driver Arrays ........................................................... 172 Source Driver Arrays ...................................................... 174 Motor Driver Arrays ........................................................ 176 Partial switching PFC Arrays ......................................... 180 Package Type (Dimensions) ........................................................... 185
2 Transistors
Ordering Information
All products listed must be ordered in standard packing increments.
Series Name/ Product Name 2SA1186 2SA1215 2SA1216 2SA1294 2SA1295 2SA1303 2SA1386 2SA1386A 2SA1488 2SA1488A 2SA1492 2SA1493 2SA1494 2SA1567 2SA1568 2SA1667 2SA1668 2SA1673 2SA1693 2SA1694 2SA1695 2SA1725 2SA1746 2SA1859 2SA1859A 2SA1860 2SA1907 2SA1908 2SA1909 2SA2151 2SA2151A 2SA2223 2SB1257 2SB1258 2SB1259 2SB1351 2SB1382 2SB1383 2SB1420 2SB1559 2SB1560 2SB1570 2SB1587 2SB1588 2SB1647 2SB1648 2SB1649 2SC2837 2SC2921 2SC2922 2SC3263 2SC3264 Standard Packing Quantities Package Bulk TO3P MT200 MT200 TO3P MT200 TO3P TO3P TO3P TO220F TO220F TO3P MT200 MT200 TO220F TO220F TO220F TO220F TO3PF TO3P TO3P TO3P TO220F TO3PF TO220F TO220F TO3PF TO3PF TO3PF TO3PF TO3P TO3P TO3P TO220F TO220F TO220F TO220F TO3PF TO3P TO3P TO3P TO3P MT200 TO3PF TO3PF TO3P MT200 TO3PF TO3P MT200 MT200 TO3P MT200 500(Box)/1080(Stick) 250(Box) 250(Box) 500(Box)/1080(Stick) 250(Box) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 500(Box)/1080(Stick) 250(Box) 250(Box) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 1000(Box)/3750(Stick) 500(Box)/1080(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 250(Box) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 250(Box) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 250(Box) 250(Box) 500(Box)/1080(Stick) 250(Box) Taping Series Name/ Product Name 2SC3284 2SC3519 2SC3519A 2SC3835 2SC3851 2SC3851A 2SC3852 2SC3852A 2SC3856 2SC3857 2SC3858 2SC3927 2SC4024 2SC4131 2SC4138 2SC4140 2SC4153 2SC4300 2SC4301 2SC4304 2SC4381 2SC4382 2SC4388 2SC4445 2SC4466 2SC4467 2SC4468 2SC4495 2SC4511 2SC4518 2SC4518A 2SC4546 2SC4706 2SC4883 2SC4883A 2SC4886 2SC5071 2SC5099 2SC5100 2SC5101 2SC5130 2SC5287 2SC6011 2SC6011A 2SC6145 2SD1785 2SD1796 2SD2014 2SD2015 2SD2016 2SD2017 2SD2045 Standard Packing Quantities Package Bulk TO3P TO3P TO3P TO3P TO220F TO220F TO220F TO220F TO3P MT200 MT200 TO3P TO220F TO3PF TO3P TO3P TO220F TO3PF TO3PF TO220F TO220F TO220F TO3PF TO3PF TO3P TO3P TO3P TO220F TO220F TO220F TO220F TO220F TO3P TO220F TO220F TO3PF TO3P TO3PF TO3PF TO3PF TO220F TO3P TO3P TO3P TO3P TO220F TO220F TO220F TO220F TO220F TO220F TO3PF 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 500(Box)/1080(Stick) 250(Box) 250(Box) 500(Box)/1080(Stick) 1000(Box)/3750(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 1000(Box)/3750(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 500(Box)/1080(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 1000(Box)/3750(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 500(Box)/1080(Stick) Taping
150
Transistors
2 Transistors
Series Name/ Product Name 2SD2081 2SD2082 2SD2083 2SD2141 2SD2389 2SD2390 2SD2401 2SD2438 2SD2439 2SD2560 2SD2561 2SD2562 2SD2641 2SD2642 2SD2643 2SK2420 2SK2701A 2SK2778 2SK2779 2SK2803 2SK2848 2SK2943 2SK3003 2SK3004 2SK3199 2SK3710A 2SK3711 2SK3800 2SK3801 EKV550 FGT312 FGT313 FGT412 FGT612 FGM603 FKP202 FKP250A FKP252 FKP253 FKP280A FKP300A FKP330C FKV460S FKV550N FKV550T FKV575 FKV660S MGD623N MGD623S SDA05 SDC03 SDC04
Standard Packing Quantities Package Bulk TO220F TO3PF TO3P TO220F TO3P TO3P MT200 TO220F TO3PF TO3P MT200 TO3PF TO3P TO220F TO3PF TO220F TO220F TO220F TO220F TO220F TO220F TO220F TO220F TO220F TO220F TO220S(Surface-mount) TO3P TO220S(Surface-mount) TO3P TO220 TO220F TO220F TO220F TO220F TO3PF TO220F TO3PF TO220F TO220F TO3PF TO3PF TO3PF TO220S(Surface-mount) TO220F TO220F TO220F TO220S(Surface-mount) TO3P TO3P PS16Pin PS16Pin PS16Pin 1000(Box)/3750(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 1000(Box)/3750(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 250(Box) 1000(Box)/3750(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 250(Box) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 1000(Box)/3750(Stick) 500(Box)/1080(Stick) 3750(Stick) 3750(Stick) 3750(Stick) 3750(Stick) 3750(Stick) 3750(Stick) 3750(Stick) 3750(Stick) 3750(Stick) 3750(Stick) 1080(Stick) 1080(Stick) 1000(Stick) 3750(Stick) 3750(Stick) 3750(Stick) 3750(Stick) 1080(Stick) 3750(Stick) 1080(Stick) 3750(Stick) 3750(Stick) 1080(Stick) 1080(Stick) 1080(Stick) 3750(Stick) 3750(Stick) 3750(Stick) 1080(Stick) 1080(Stick) Taping 1000 1000 1000 1000 1200 1200 1200
Series Name/ Product Name SDC06 SDC07 SDH02 SKP202 SKP253 SLA4xxx SLA4xxx SLA5xxx SLA5xxx SLA6xxx SMA4xxx SMA5xxx SMA5xxx SMA6xxx STAxxx STAxxx STD01N STD01P STD03N STD03P
Standard Packing Quantities Package Bulk PS16Pin PS16Pin PS16Pin TO263(Surface-mount) TO263(Surface-mount) SLA12Pin SLA21Pin SLA12Pin SLA15Pin SLA12Pin SMA12Pin SMA12Pin SMA15Pin SMA12Pin STA8Pin STA10Pin TO3P-5 TO3P-5 TO3P-5 TO3P-5 250(Box)/1080(Stick) 250(Box)/1080(Stick) 250(Box)/1080(Stick) 250(Box)/1080(Stick) 250(Box)/1080(Stick) 1440(Stick) 1440(Stick) 1440(Stick) 1440(Stick) 1000(Box)/4050(Stick) 3200(Box)/3300(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) Taping 1200 1200 1200 800 800
Transistors
151
2 Transistors
Application Note
Since reliability can be affected adversely by improper storage environment or handling methods during Characteristic tests, please observe the following cautions.
Heatsink
A larger contact area between the device and the heatsink is required for more effective heat radiation. To ensure a larger contact area, minimize mounting holes. And select a heatsink with a surface smooth enough and free from burrs and slivers.
Soldering Temperature
In general, the device mounted on a printed circuit board is subjected to high temperatures from flow solder in a solder bath, or, from a soldering iron at hand soldering. The testing method and test conditions (JIS-C-7021 standards) for a device's heat resistance to soldering are: At a distance of 1.5mm from the device's main body, apply 260C for 10 seconds, and 350C for 3 seconds. Please observe these limits and finish soldering in as short a time as possible.
Silicone Grease
When using a heatsink, please coat thinly and evenly the back surface of the device and both surfaces of the insulating plate with silicone grease to lower the thermal resistance between the device and the heatsink. Please select proper silicone grease carefully since the oil in some grease products may penetrate the device and result in an extremely short device life. Recommended Silicone Grease G-746 (Shin-Etsu Chemical) YG6260 (Momentive Performance Materials Inc.) SC102 (Dow Corning Toray Silicone)
Mounting Torque
When mounting torque is insufficient, thermal resistance increases, and so heat radiation effect is decreased. When the torque is excessive, the screw may be broken, the heatsink may be deformed, and the device frame may be distorted, resulting in the device damage. Recommended mounting torque per package is as follows:
* When the surface of a heatsink where Full Mold package is to be mounted is not flat due to the burred metal bracket for screwing around the mounting hole of the heatsink, the resin of the package might be cracked even if the torque is lower than the recommended value. * When a screw is fastened with an air driver for the Full Mold package, a large impact is generated at the time of stop, and the resin may crack even if the torque is lower than the recommended value. An electric driver, therefore, should be used instead of an air driver.
152
Transistors
2-1 Transistors
Selection Guide
V CEO-I C
800 600 550 C4304 C4445 C4300 C4301 C4706 C4518 C4518A C5287 C5130 D2141 D2017 A1294 C3263 A2151A C6011A 2SA2223 2SC6145 A1493 C3857 A2151 C6011 A1386A A1492 A1673 C3519A C3856 C4388 A1215 A1386 C2921 C3519 B1647 B1649 D2560 D2562 A1295 C3264 C4546 C3927
C4138
C5071
C4140
200
A1668 C4382
D2016
A1494 C3858
180
A1859A C4883A
A1216 C2922
160
150
140
120
D2015
D1785 D2045
C3835 C4153
A1186 B1560 B1588 C2837 D2390 D2439 A1695 A1909 C4468 C5101 B1259 D2081
B1570 D2401
B1648 D2561
B1383 D2083
110
100 80
C3852A
D2641 D2642 D2643 B1258 A1693 A1725 A1907 C4466 C4511 C5099 A1568 B1351
60
C3852
50
C4495
A1567 A1746 12 14
C4131
10
15
16
17
18
25
Transistors
153
2-1 Transistors
Audio Transistors
Output Transistors
Chip Pc (W) 30 60 Ic (A) 6 6 6 75 8 8 8 10 80 8 10 14 85 15 15 10 100 10 10 125 14 15 15 130 15 15 15 12 150 15 15 15 160 15 15 17 200 17 17 17 VCEO (V) 80 80 80 120 150 120 140 150 150 150 150 180 140 150 150 150 150 160 180 180 230 150 160 200 200 230 230 150 180 200 230 2SA1494 2SC3858 2SA1295 2SC3264 2SA1216 2SC2922 2SA1493 2SA2151 2SA2151A 2SA2223 2SC3857 2SC6011 2SC6011A 2SC6145 2SB1648 2SD2561 2SA1215 2SC2921 2SA1492 2SC3856 2SA1386A 2SA1294 2SC3519A 2SC3263 2SB1570 2SD2401 2SA1386 2SC3519 2SA1303 2SC3284 2SB1647 2SD2560 2SA1673 2SA1695 2SC4388 2SC4468 2SA1186 2SC2837 2SB1560 2SD2390 2SA1860 2SC4886 2SB1649 2SD2562 2SA1694 2SA1909 2SC4467 2SC5101 2SB1559 2SB1588 2SD2389 2SD2439 2SA1725 2SA1693 2SA1907 2SA1908 General 2SC4511 2SC4466 2SC5099 2SC5100 2SB1587 2SD2438 Single Transistors LAPT Darlington TO-220F (FM20) TO-3P (MT-100) TO-3PF (FM100) TO-3PF (FM100) TO-3PF (FM100) TO-3P (MT-100) TO-3PF (FM100) TO-3P (MT-100) TO-3PF (FM100) TO-3PF (FM100) TO-3PF (FM100) TO-3PF (FM100) TO-3P (MT-100) TO-3P (MT-100) TO-3P (MT-100) TO-3P (MT-100) TO-3P (MT-100) TO-3P (MT-100) TO-3P (MT-100) TO-3P (MT-100) TO-3P (MT-100) MT-200 (fixed at two points) MT-200 (fixed at two points) MT-200 (fixed at two points) TO-3P (MT-100) TO-3P (MT-100) TO-3P (MT-100) MT-200 (fixed at two points) MT-200 (fixed at two points) MT-200 (fixed at two points) MT-200 (fixed at two points) Package
Output Transistors with Temperature Compensating Function (Refer to our Web site for applications)
Part Number STD01P STD03P STD01N STD03N Pc (W) 100 160 IC (A) 10 15 VCEO (V) 150 160 Package TO3P-5pin TO3P-5pin
154
Transistors
2-1 Transistors
Switching Transistors
DC-DC Converter
Part Number 2SC4024 2SC4131 2SC4153 2SC3835 100 200 VCBO (V) VCEO (V) 50 IC (A) 10 15 120 7 PC (W) 35 60 30 70 TO-220F TO-3PF TO-220F TO-3P Package
Transistors
155
2-1 Transistors
min 50 50 30 50 50 50 50 50 40 40 50 50 50 50 50 60 60 50 50 50 50 50 50 60 60 50 50 50 50 50 50 40 2000 1000 2000 2000 2000 2000 2000 5000 5000 5000 5000 5000 5000 5000 5000
4 4 4 1 1 10 10
4 4 4 4 4 1
10 10 4 4 4 4 4 4 4 4 2 4 4 4 4 4
4 4 4 4 4 4 4 4
156
Transistors
2-1 Transistors
VCE (sat)
Electrical Characteristics VBE (sat) Conditions (V) (V) Ic IB max max (A) (A) 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 0.5 0.5 2.0 3.0 2.5 0.35 0.35 1.0 1.0 2.0 1.5 1.5 0.5 0.5 0.5 1.0 1.0 2.0 0.5 0.5 0.5 0.5 0.5 0.5 1.5 1.5 1.5 1.5 1.5 1.8 1.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.0 2.0 2.0 2.0 2.5 2.5 2.5 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 1.2 5 5 8 5 5 5 5 5 2 2 5 10 10 6 6 0.7 0.7 5 2 3 5 2 5 0.7 0.7 5 12 3 5 5 5 5 3 3 5 10 8 12 8 6 7 7 6 7 10 10 10 0.5 0.5 0.8 0.5 0.5 0.5 0.5 0.5 0.2 0.2 0.5 1 1 0.3 0.3 0.07 0.07 0.5 0.2 0.3 0.5 0.2 0.08 0.07 0.07 0.5 0.2 0.3 0.5 0.5 0.5 0.5 0.006 0.006 0.01 0.02 0.016 0.024 0.016 0.006 0.007 0.007 0.006 0.007 0.01 0.01 0.01
fT Conditions VCE IE (V) (A) 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 1 2 2 2 2 2 2 2 0.2 0.2 0.5 0.5 1 0.5 0.5 0.2 0.2 0.5 0.5 0.5 0.5 0.5 1 0.7 0.7 2 0.5 0.5 0.5 0.5 0.5 2 0.2 0.2 0.2 1 1 1 1 1 2 2 1 2 2 2 2
ton (S) 0.25typ 0.25typ 0.3typ 0.35typ 0.35typ 0.25typ 0.3typ 0.3typ 0.25typ 0.25typ 0.6typ 0.3typ 0.6typ 0.4typ 0.4typ 0.4typ 0.4typ 0.6typ 0.18typ 0.14typ 0.17typ 0.18typ 0.5typ 0.5typ 0.5typ 0.25typ 0.18typ 0.14typ 0.17typ 0.4typ 0.6typ 0.6typ 0.7typ 0.8typ 1typ 1typ 0.7typ 0.8typ 0.8typ 0.7typ 0.8typ 0.7typ 0.7typ 0.7typ
Switching Time tstg (S) 0.8typ 0.85typ 0.7typ 1.5typ 1.5typ 0.85typ 0.7typ 0.7typ 0.75typ 0.75typ 0.9typ 0.9typ 0.9typ 0.4typ 0.4typ 1.5typ 1.5typ 0.9typ 1.1typ 1.4typ 1.86typ 1.1typ 0.6typ 1typ 1typ 0.85typ 1.1typ 1.4typ 1.86typ 0.8typ 1.6typ 1.6typ 1.5typ 1.8typ 3typ 3typ 3.6typ 3typ 3typ 3.6typ 3typ 1.6typ 1.6typ 1.6typ
Mass tf (S) 0.2typ 0.2typ 0.2typ 0.3typ 0.3typ 0.2typ 0.2typ 0.2typ 0.25typ 0.25typ 0.2typ 0.2typ 0.2typ 0.2typ 0.2typ 0.5typ 0.5typ 0.2typ 0.21typ 0.21typ 0.27typ 0.21typ 0.3typ 0.5typ 0.5typ 0.2typ 0.21typ 0.21typ 0.27typ 0.6typ 0.5typ 0.5typ 0.6typ 1typ 1typ 1typ 0.9typ 1.2typ 1.2typ 0.9typ 1.2typ 1.1typ 1.1typ 1.1typ Cob (pF) 110typ 400typ 500typ 500typ 500typ 400typ 500typ 500typ 90typ 90typ 500typ 400typ 500typ 330typ 330typ 60typ 60typ 500typ 150typ 300typ 400typ 150typ 400typ 30typ 30typ 400typ 150typ 300typ 400typ 450typ 450typ 500typ 75typ 100typ 145typ 170typ 350typ 230typ 350typ 160typ 230typ 230typ 160typ 230typ 320typ 320typ 320typ 2SD2389 2SD2390 2SD2401 2SD2438 2SD2439 2SD2560 2SD2561 2SD2562 2SD2082 2SD2083 2SC4883 2SC4883A 2SC4886 2SC5099 2SC5100 2SC5101 2SC6011 2SC6011A 2SC6145 2SD2014 2SD1785 2SD2081 2SC4381 2SC4382 2SC4388 2SC4466 2SC4467 2SC4468 2SC4511 2SC2837 2SC2921 2SC2922 2SC3263 2SC3264 2SC3284 2SC3519 2SC3519A 2SC3851 2SC3851A 2SC3856 2SC3857 2SC3858 TO-3P (MT-100) MT-200 MT-200 TO-3P (MT-100) MT-200 TO-3P (MT-100) TO-3P (MT-100) TO-3P (MT-100) TO-220F (FM20) TO-220F (FM20) TO-3P (MT-100) MT-200 MT-200 TO-220F (FM20) TO-220F (FM20) TO-220F (FM20) TO-220F (FM20) TO-3PF (FM100) TO-3P (MT-100) TO-3P (MT-100) TO-3P (MT-100) TO-220F (FM20) TO-3PF (FM100) TO-220F (FM20) TO-220F (FM20) TO-3PF (FM100) TO-3PF (FM100) TO-3PF (FM100) TO-3PF (FM100) TO-3P (MT-100) TO-3P (MT-100) TP-3P (MT-100) TO-220F (FM20) TO-220F (FM20) TO-220F (FM20) TO-220F (FM20) TO-3PF (FM100) TO-3P (MT-100) TO-3P (MT-100) TO-3P (MT-100) TO-3P (MT-100) MT-200 TO-3PF (FM100) TO-3PF (FM100) TO-3P (MT-100) MT-200 TO-3PF (FM100) Complementary Package (g) 6.0 18.4 18.4 6.0 18.4 6.0 6.0 6.0 2.0 2.0 6.0 18.4 18.4 2.0 2.0 2.0 2.0 6.5 6.0 6.0 6.0 2.0 6.5 2.0 2.0 6.5 6.5 6.5 6.5 6.0 6.0 6.0 2.0 2.0 2.0 2.0 6.5 6.0 6.0 6.0 6.0 18.4 6.5 6.5 6.0 18.4 6.5
Transistors
157
2-1 Transistors
Absolute Maximum Ratings Part Number Applications VCBO (V) 2SC2837 2SC2921 2SC2922 2SC3263 2SC3264 2SC3284 2SC3519 2SC3519A 2SC3835 2SC3851 2SC3851A 2SC3852 2SC3852A 2SC3856 2SC3857 2SC3858 2SC3927 2SC4024 2SC4131 2SC4138 2SC4140 2SC4153 2SC4300 2SC4301 2SC4304 2SC4381 2SC4382 2SC4388 2SC4445 2SC4466 2SC4467 2SC4468 2SC4495 2SC4511 2SC4518 2SC4518A 2SC4546 2SC4706 2SC4883 2SC4883A 2SC4886 2SC5071 2SC5099 2SC5100 2SC5101 2SC5130 2SC5287 2SC6011 2SC6011A 2SC6145 Audio, general-purpose Audio, general-purpose Audio, general-purpose Audio, general-purpose Audio, general-purpose Audio, general-purpose Audio, general-purpose Audio, general-purpose Humidifier, DC-DC converter, general-purpose Audio, PPC high voltage power supply, general-purpose Audio, PPC high voltage power supply, general-purpose Solenoid/motor driver/series regulator, general-purpose Solenoid/motor driver/series regulator, general-purpose Audio, general-purpose Audio, general-purpose Audio, general-purpose Switching regulator, general-purpose DC-DC converter, emergency lamp inverter, general-purpose DC-DC converter, emergency lamp inverter, general-purpose Switching regulator, general-purpose Switching regulator, general-purpose Humidifier, DC-DC converter, general-purpose Switching regulator, general-purpose Switching regulator, lighting inverter, general-purpose Switching regulator, general-purpose TV vertical output, audio output driver, general-purpose TV vertical output, audio output driver, general-purpose Audio, general-purpose Switching regulator, general-purpose Audio, general-purpose Audio, general-purpose Audio, general-purpose For audio temperature compensation, general-purpose Audio, general-purpose Switching regulator, lighting inverter, general-purpose Switching regulator, lighting inverter, general-purpose Switching regulator, lighting inverter, general-purpose Switching regulator, general-purpose Audio output driver, TV velocity modulation Audio output driver, TV velocity modulation Audio, general-purpose Switching regulator, general-purpose Audio, general-purpose Audio, general-purpose Audio, general-purpose Switching regulator, general-purpose Switching regulator, general-purpose Audio, general-purpose Audio, general-purpose Audio, general-purpose 150 160 180 230 230 150 160 180 200 80 100 80 100 200 200 200 900 100 100 500 500 200 900 900 900 150 200 200 900 120 160 200 80 120 900 1000 600 900 150 180 150 500 120 160 200 600 900 200 230 230 VCEO (V) 150 160 180 230 230 150 160 180 120 60 80 60 80 180 200 200 550 50 50 400 400 120 800 800 800 150 200 180 800 80 120 140 50 80 550 550 400 600 150 180 150 400 80 120 140 400 550 200 230 230 Ic (A) 10 15 17 15 17 14 15 15 7 (Pulse 14) 4 4 3 3 15 15 17 10 (Pulse 15) 10 15 (Pulse 20) 10 (Pulse 20) 18 (Pulse 36) 7 (Pulse 14) 5 (Pulse 10) 7 (Pulse 14) 3 (Pulse 6) 2 2 15 3 (Pulse 6) 6 8 10 3 6 5 (Pulse 10) 5 (Pulse 10) 7 (Pulse 14) 14 (Pulse 28) 2 2 14 12 (Pulse 24) 6 8 10 5 (Pulse 10) 5 (Pulse 10) 15 15 15 Pc (W) 100 150 200 130 200 125 130 130 70 25 25 25 25 130 150 200 120 35 60 80 130 30 75 80 35 25 25 85 60 60 80 100 25 30 35 35 30 130 20 20 80 100 60 75 80 30 80 160 160 160 ICBO Conditions VCB (A) (V) 100 100 100 100 100 100 100 100 100 100 100 10 10 100 100 100 100 100 10 100 100 100 100 100 100 10 10 10 100 10 10 10 10 10 100 100 100 100 10 10 100 100 10 10 10 100 100 10 10 10 150 160 180 230 230 150 160 180 200 80 100 80 100 200 200 200 800 100 100 500 500 200 800 800 800 150 200 200 800 120 160 200 80 120 800 800 600 800 150 180 150 500 120 160 200 500 800 200 230 230 hFE
max 180 180 180 140 140 180 180 180 220 320 320
4 4 4 4 4 1 4 4 4 4 4 4 10 10
4 4 4 4 4 4
180 25 25 25 25 240 240 180 30 180 180 180 30 25 180 180 140
4 4 4 4 4 10 10 4 4 4 4 4 4 4 4 4 4
158
Transistors
2-1 Transistors
VCE (sat)
Electrical Characteristics VBE (sat) Conditions (V) (V) Ic IB max max (A) (A) 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 0.5 0.5 0.5 0.5 0.5 2.0 3.0 2.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 1.0 1.0 2.0 0.5 1.5 1.5 0.5 0.5 0.5 0.5 0.5 0.7 0.5 1.0 1.0 2.0 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 1.3 1.2 1.3 1.2 1.2 1.3 1.2 1.2 1.2 1.3 1.3 1.2 1.2 1.2 1.2 1.2 1.2 5 5 8 5 5 5 5 5 3 2 2 2 2 5 10 10 5 5 5 6 10 3 2 3 7 7 7 5 0.7 2 3 5 4 2 1.8 1.8 3 7 0.7 0.7 5 7 2 3 5 1.5 1.8 5 5 5 0.5 0.5 0.8 0.5 0.5 0.5 0.5 0.5 0.3 0.2 0.2 0.05 0.05 0.5 1 1 1 0.1 0.08 1.2 2 0.3 0.4 0.6 0.14 0.07 0.07 0.5 0.14 0.2 0.3 0.5 0.02 0.2 0.36 0.36 0.6 1.4 0.07 0.07 0.5 1.4 0.2 0.3 0.5 0.3 0.36 0.5 0.5 0.5
fT Conditions VCE IE (V) (A) 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 1 2 2 2 2 2 2 2 0.5 0.2 0.2 0.2 0.2 0.5 0.5 1 1 0.5 1 0.7 2.0 0.5 0.5 1 0.3 0.2 0.2 0.5 0.3 0.5 0.5 0.5 0.1 0.5 0.35 0.35 0.5 1.5 0.7 0.7 2 1 0.5 0.5 0.5 0.3 0.35 0.5 0.5 2
ton (S) 0.2typ 0.2typ 0.2typ 0.3typ 0.3typ 0.2typ 0.2typ 0.2typ 0.5max 0.2typ 0.2typ 0.8typ 0.8typ 0.5typ 0.3typ 0.5typ 1max 0.5typ 0.5typ 1max 1max 0.5max 1max 1max 0.7max 1typ 1typ 0.5max 0.7max 0.16typ 0.13typ 0.24typ 0.45typ 0.16typ 0.7max 0.7max 0.5max 1max 0.5typ 0.5typ 0.26typ 1max 0.16typ 0.13typ 0.24typ 1max 0.7max
Switching Time tstg (S) 1.4typ 1.5typ 1.3typ 2.4typ 2.4typ 1.5typ 1.3typ 1.3typ 3max 1typ 1typ 3typ 3typ 1.8typ 2.4typ 1.8typ 5max 2typ 2typ 3max 3max 3max 5max 5max 4max 3typ 3typ 1.8max 4max 2.6typ 3.5typ 4.32typ 1.6typ 2.6typ 4max 4max 2max 5max 1.5typ 1.5typ 1.5typ 3max 2.6typ 3.5typ 4.32typ 2max 4max
Mass tf (S) 0.35typ 0.35typ 0.45typ 0.5typ 0.5typ 0.35typ 0.45typ 0.45typ 0.5max 0.3typ 0.3typ 1.2typ 1.2typ 0.6typ 0.4typ 0.6typ 0.5max 0.5typ 0.4typ 0.5max 0.5max 0.5max 1max 1max 0.7max 1.5typ 1.5typ 0.6max 0.7max 0.34typ 0.32typ 0.4typ 0.85typ 0.34typ 0.5max 0.5max 0.15max 0.7max 0.5typ 0.5typ 0.35typ 0.5max 0.34typ 0.32typ 0.4typ 0.3max 0.5max Cob (pF) 60typ 200typ 250typ 250typ 250typ 200typ 250typ 250typ 110typ 60typ 60typ 50typ 50typ 300typ 250typ 300typ 105typ 150typ 210typ 85typ 165typ 110typ 75typ 105typ 50typ 35 35 300 50 110 200 250 30 110 50 50 55 160 30 30 200 105 110 200 250 30 50 270 270 250 2SA2151 2SA2151A 2SA2223 2SA1907 2SA1908 2SA1909 2SA1859 2SA1859A 2SA1860 2SA1725 2SA1693 2SA1694 2SA1695 2SA1667 2SA1668 2SA1673 2SA1492 2SA1493 2SA1494 2SA1488 2SA1488A 2SA1186 2SA1215 2SA1216 2SA1294 2SA1295 2SA1303 2SA1386 2SA1386A TO-3P (MT-100) MT-200 MT-200 TO-3P (MT-100) MT-200 TO-3P (MT-100) TO-3P (MT-100) TO-3P (MT-100) TO-3P (MT-100) TO-220F (FM20) TO-220F (FM20) TO-220F (FM20) TO-220F (FM20) TO-3P (MT-100) MT-200 MT-200 TO-3P (MT-100) TO-220F (FM20) TO-3PF (FM100) TO-3P (MT-100) TO-3P (MT-100) TO-220F (FM20) TO-3PF (FM100) TO-3PF (FM100) TO-220F (FM20) TO-220F (FM20) TO-220F (FM20) TO-3PF (FM100) TO-3PF (FM100) TO-3P (MT-100) TO-3P (MT-100) TO-3P (MT-100) TO-220F (FM20) TO-220F (FM20) TO-220F (FM20) TO-220F (FM20) TO-220F (FM20) TO-3P (MT-100) TO-220F (FM20) TO-220F (FM20) TO-3PF (FM100) TO-3P (MT-100) TO-3PF (FM100) TO-3PF (FM100) TO-3PF (FM100) TO-220F (FM20) TO-3P (MT-100) TO-3P (MT-100) TO-3P (MT-100) TP-3P (MT-100) Complementary Package (g) 6.0 18.4 18.4 6.0 18.4 6.0 6.0 6.0 6.0 2.0 2.0 2.0 2.0 6.0 18.4 18.4 6.0 2.0 6.5 6.0 6.0 2.0 6.5 6.5 2.0 2.0 2.0 6.5 6.5 6.0 6.0 6.0 2.0 2.0 2.0 2.0 2.0 6.0 2.0 2.0 6.5 6.0 6.5 6.5 6.5 2.0 6.0 6.0 6.0 6.0
Transistors
159
2-1 Transistors
Absolute Maximum Ratings Part Number Applications VCBO (V) 2SD1785 2SD1796 2SD2014 2SD2015 2SD2016 2SD2017 2SD2045 2SD2081 2SD2082 2SD2083 2SD2141 2SD2389 2SD2390 2SD2401 2SD2438 2SD2439 2SD2560 2SD2561 2SD2562 2SD2641 2SD2642 2SD2643 STD01N STD01P STD03N STD03P Solenoid/relay/motor driver/series regulator, general-purpose Solenoid/relay/motor driver, general-purpose Solenoid/relay/motor driver/series regulator, general-purpose Solenoid/relay/motor driver, general-purpose Igniter, relay, general-purpose Solenoid/relay/motor driver, general-purpose Solenoid/motor driver, general-purpose Solenoid/motor driver, general-purpose Solenoid/motor driver, general-purpose Solenoid/motor driver, general-purpose Igniter, solenoid, motor driver, general-purpose Audio, series regulator, general-purpose Audio, series regulator, general-purpose Audio, series regulator, general-purpose Audio, series regulator, general-purpose Audio, series regulator, general-purpose Audio, series regulator, general-purpose Audio, series regulator, general-purpose Audio, series regulator, general-purpose Series regulator, general-purpose Series regulator, general-purpose Series regulator, general-purpose Audio Audio Audio Audio 120 6010 120 150 200 300 120 120 120 120 38050 160 160 160 160 160 150 150 150 110 110 110 150 150 160 160 VCEO (V) 120 6010 80 120 200 250 120 120 120 120 38050 150 150 150 150 150 150 150 150 110 110 110 150 150 160 160 Ic (A) 6 (Pulse 10) 4 4 4 3 6 6 (Pulse 10) 10 (Pulse 15) 16 (Pulse 26) 25 (Pulse 40) 6 (Pulse 10) 8 10 12 8 10 15 17 15 6 6 6 10 10 15 15 Pc (W) 30 25 25 25 25 35 50 30 75 120 35 80 100 150 75 80 130 200 85 60 30 60 100 100 160 160 ICBO Conditions VCB (A) (V) 10 10 10 10 10 100 10 10 10 10 10 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 120 50 120 150 200 300 120 120 120 120 330 160 160 160 160 160 150 150 150 110 110 110 150 150 160 160 hFE
min 2000 2000 2000 2000 1000 2000 2000 2000 2000 2000 1500 5000 5000 5000 5000 5000 5000 5000 5000 5000 5000 5000 5000 5000 5000 5000
max
15000
4 2 2 4 4 4 2
30000 30000 30000 30000 30000 30000 30000 30000 30000 30000 30000 20000 20000 20000 20000
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
160
Transistors
2-1 Transistors
VCE (sat)
Electrical Characteristics VBE (sat) Conditions (V) (V) Ic IB max max (A) (A) 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.8 1.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.0 2.0 2.0 2.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 2.5 2.5 2.5 2.5 2.0 2.0 2.0 2.0 2.0 2.0 2.5 2.5 2 3 3 2 1 2 3 5 8 12 4 6 7 7 6 7 10 10 10 5 5 5 6 6 10 10 3mA 10mA 3mA 2mA 1.5mA 2mA 3mA 5mA 16mA 24mA 20mA 6mA 7mA 7mA 6mA 7mA 10mA 10mA 10mA 5mA 5mA 5mA 6mA 6mA 10mA 10mA
MHz 100 60 75 40 90 20 50 60 20 20 20 80 55 55 80 55 70 70 70 60 60 60
fT Conditions VCE IE (V) (A) 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 0.1 0.2 0.1 0.1 0.1 1 1 0.5 1 1 0.5 1 2 2 1 2 2 2 2 2 0.5 0.5
Mass tf (S) 1.5typ 1.5typ 1.5typ 2typ Cob (pF) 70 45 45 40 40 2SB1257 2SB1258 TO-220F (FM20) TO-220F (FM20) TO-220F (FM20) TO-220F (FM20) TO-220F (FM20) TO-220F (FM20) TO-3PF (FM100) 2SB1259 2SB1382 2SB1383 TO-220F (FM20) TO-3PF (FM100) TO-3P (MT-100) TO-220F (FM20) 2SB1559 2SB1560 2SB1570 2SB1587 2SB1588 2SB1647 2SB1648 2SB1649 TO-3P (MT-100) TO-3P (MT-100) MT-200 TO-3PF (FM100) TO-3PF (FM100) TO-3P (MT-100) MT-200 TO-3PF (FM100) TO-3P (MT-100) TO-220F (FM20) TO-3PF (FM100) STD01P STD01N STD03P STD03N TO3P-5Pin TO3P-5Pin TO-3P-5pin TO-3P-5pin Complementary Package (g) 2.0 2.0 2.0 2.0 2.0 2.0 6.5 2.0 6.5 6.0 2.0 6.0 6.0 18.4 6.5 6.5 6.0 18.4 6.5 6.0 2.0 6.5 6.2 6.2 6.2 6.2
0.6typ 0.5typ
16typ 5.5typ
3typ 1.5typ
65 70 95
0.6typ 1typ
7typ 6typ
1.5typ 1typ
210 340 95
0.6typ 0.5typ 0.5typ 0.6typ 0.5typ 0.8typ 0.8typ 0.8typ 0.8typ 0.8typ 0.8typ
10typ 10typ 10typ 10typ 10typ 4typ 4typ 4typ 6.2typ 6.2typ 6.2typ
0.9typ 1.1typ 1.1typ 0.9typ 1.1typ 1.2typ 1.2typ 1.2typ 1.1typ 1.1typ 1.1typ
Transistors
161
162
Transistors
Selection Guide
By VDSS
VDSS (V) 40 RDS (ON) () max 6.0m 6.0m 9m 10m 50 13m 15m 15m 6.0m 60 6.0m 14m 28m 100 80m 0.175 53m 200 53m 0.175 43m 75m 250 95m 95m 0.25 280 300 330 450 500 600 900 53m 65m 63m 1.1 2.8 1.5 3.8 5.0 ID (A) 70 70 60 75 50 50 50 70 70 60 30 20 12 45 45 18 50 25 20 20 18 40 30 30 7 3 5 2 3 PD (W) 80 100 60 40 35 35 85 90 130 60 40 35 30 40 95 35 85 40 40 40 35 85 85 85 35 30 30 30 30
Part Number 2SK3800 2SK3801 FKV460S FKV575 FKV550T FKV550N EKV550 2SK3710A 2SK3711 FKV660S 2SK2420 2SK2779 2SK2778 FKP202 SKP202 2SK3003 FKP250A FKP252 FKP253 SKP253 2SK3004 FKP280A FKP300A FKP330C 2SK2701A 2SK2803 2SK3199 2SK2848 2SK2943
Package TO220S (Surface-mount) TO3P(MT100) TO220S (Surface-mount) TO220F(FM20) TO220F(FM20) TO220F(FM20) TO220 TO220S (Surface-mount) TO3P(MT100) TO220S (Surface-mount) TO220F(FM20) TO220F(FM20) TO220F(FM20) TO220F(FM20) TO263 (Surface-mount) TO220F(FM20) TO3PF(FM100) TO220F(FM20) TO220F(FM20) TO263 (Surface-mount) TO220F(FM20) TO3PF(FM100) TO3PF(FM100) TO3PF(FM100) TO220F(FM20) TO220F(FM20) TO220F(FM20) TO220F(FM20) TO220F(FM20)
Transistors
163
164
Transistors
Electrical Characteristics Re (yfs) Conditions (S) ID VDS typ (V) (A) min 13 3.5 7 12 1.5 1.2 1.8 7 7 3.5 30 30 30 30 17 18 30 13 8 25 20 23 20 20 17 30 20 18 8 28 17 28 42 21 17 38 33 37 20 5 11 20 2.1 1.7 2.8 11 11 5.2 80 80 50 50 10 20 10 10 20 20 20 10 10 20 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 15 3.5 6 10 1.5 1 1.5 9 9 2.5 35 35 35 35 25 22 25 12 10 20 15 15 25 25 25 37 25 22 10
Ciss (pF) typ 2200 720 740 1630 340 290 600 850 850 650 8000 8000 5100 5100 2000 2000 3800 2000 1600 3800 3800 4600 2800 2700 2000 3200 2500 2000 1600
Crss (pF) typ Conditions VDS VGS (V) (V) 0 62 75 180 26 30 40 250 250 110 1000 1000 860 860 500 80 210 70 50 190 180 220 600 500 500 750 150 80 50 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 25 10 10 10 10 10 10 10 10 10 10 10 10 10 10 25 25 25 25 25 25 25 10 10 10 10 10 25 25 () typ 21m 0.84 105m 60m 2.1 3 4 130m 0.2 1.2 5m 5m 5m 5m 12m 45m 37m 68m 86m 46m 57m 50m 7m 10m 12m 7m 11m 45m 86m max 28m 1.1 175m 80m 2.8 3.8 5 175m 0.25 1.5 6m 6m 6m 6m 15m 53m 43m 75m 95m 53m 65m 63m 9m 13m 15m 10m 14m 53m 95m
RDS (ON) Conditions VGS ID (V) (A) 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 15 3.5 6 10 1.5 1 1.5 9 9 2.5 35 35 35 35 25 22 25 12 10 20 15 15 25 25 25 37 25 22 10 130m 75m 220m 95m 4 4 () typ max Conditions VGS ID (V) (A) Package
Mass
(g) TO220F(FM20) TO220F(FM20) 6 TO220F(FM20) 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0
TO220S(Surface-mount) 1.5 TO3P(MT100) TO220 TO220F(FM20) TO3PF(FM100) TO220F(FM20) TO220F(FM20) TO3PF(FM100) TO3PF(FM100) TO3PF(FM100) 6.0 2.0 2.0 6.5 2.0 2.0 6.5 6.5 6.5
Transistors
165
166
Transistors
2-3 IGBT
Selection Guide
By VCES
VCES (V) 330 330 400 600 600 600 600 600 IC (A) 20 30 20 20 30 30 50 50 PC (W) 35 35 35 35 60 60 150 150
Part Number FGT312 FGT313 FGT412 FGT612 FGM603 FGM623S MGD623N MGD623S
Transistors
167
2-3 IGBT
168
Transistors
2-3 IGBT
Electrical Characteristics (Ta=25C) td(off) tr tf td(on) (ns) typ 130 100 15 20 15 25 75 75 (ns) typ 70 80 30 90 35 60 70 70 (ns) typ 340 300 55 90 55 70 250 250 (ns) typ 200 120 210 180 220 190 200 120 IC (A) 30 30 20 60 20 20 50 50 Conditions VCE (V) 300 L Load 300 L Load 150 R Load 250 R Load 200 R Load 300 R Load 300 L Load 300 L Load
Qgc (nC) typ 30 20 10 20 10 9 20 20 IC (A) Conditions VCE VGE (V) (V) 300 300 150 250 200 300 300 300 15 15 15 15 15 15 15 15
VF (V) typ
trr Conditions IF (s) (A) typ max Conditions IF di/dt (A) (A/s) Package
Mass
(g) TO3PF(FM100) 6.5 TO3PF(FM100) 6.5 TO220F(FM20) 2.0 TO220F(FM20) 2.0 TO220F(FM20) 2.0 TO220F(FM20) 2.0
30 30 20 60 20 20 50 50
1.2 1.2
1.6 1.6
30 30
0.3 0.3
30 30
Transistors
169
170
Transistors
Part Number SMA4020 SMA4021 SMA4030 SMA4032 SMA4033 SMA4036 SMA4038 SMA5106 SMA5112 SMA5117 SMA5118 SMA5125 SMA5127 SMA5130 SMA5131 SMA5132 SMA5133 SMA6010 SMA6080 SMA6511 STA301A STA302A STA303A STA322A STA401A STA402A STA403A STA404A STA406A STA408A STA412A STA413A STA421A STA431A STA434A STA457C STA460C STA471A STA472A STA473A STA475A STA481A STA485A
Category For source driver For source driver For sink driver For sink driver For sink driver For sink driver For sink driver For sink driver For 3-phase motor driver For 3-phase motor driver For 3-phase motor driver For 3-phase motor driver For 3-phase motor driver For 3-phase motor driver For 3-phase motor driver For 3-phase motor driver For 3-phase motor driver For 3-phase motor driver For 3-phase motor driver For driving stepping motor with two supplies For sink driver For source driver/3-phase motor driver For sink driver/3-phase motor driver For source driver For sink driver For source driver For sink driver For sink driver For sink driver For source driver For sink driver For sink driver For source driver H bridge H bridge H bridge For sink driver For sink driver For source driver For sink driver For sink driver For sink driver For sink driver
Circuit Count 4 4 4 4 4 6 6 4 6 6 6 6 6 6 6 6 6 6 6 5 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 2 4 4 4 4 4 4
VCEO VDSS VCES (V) 60 60 100 100 100 120 120 100 250 250 500 60 60 250 250 500 500 60 60 100 15/60 6010 50 100 50 6010 50 100 200 6010 120 60 355 60 60 60 60 6010 6010 60 100 10015 6010 10015
Package SIP12 (SMA12Pin) SIP12 (SMA12Pin) SIP12 (SMA12Pin) SIP12 (SMA12Pin) SIP12 (SMA12Pin) SIP15 (SMA15Pin) SIP15 (SMA15Pin)
Mass (g) 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 2.0 2.0 2.0 2.0 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6
0.55 0.5 0.25 1.4 0.14 0.55 2000 0.9 1.8 4 2 2000 2000 2000 1000 1000 1000 100 1000 1000 1000 1000 2000 2000 300 500 40 40 1000 2000 700 2000 2000 2000 2000 2000 2000
SIP12 (SMA12Pin) SIP12 (SMA12Pin) SIP12 (SMA12Pin) SIP12 (SMA12Pin) SIP12 (SMA12Pin) SIP12 (SMA12Pin) SIP15 (SMA15Pin) SIP12 (SMA12Pin) SIP12 (SMA12Pin) SIP12 (SMA12Pin) SIP12 (SMA12Pin) SIP12 (SMA12Pin) SIP12 (SMA12Pin) SIP8 (STA8Pin) SIP8 (STA8Pin) SIP8 (STA8Pin) SIP8 (STA8Pin) SIP10 (STA10Pin) SIP10 (STA10Pin) SIP10 (STA10Pin) SIP10 (STA10Pin) SIP10 (STA10Pin) SIP10 (STA10Pin) SIP10 (STA10Pin) SIP10 (STA10Pin) SIP10 (STA10Pin) SIP10 (STA10Pin) SIP10 (STA10Pin) SIP10 (STA10Pin) SIP10 (STA10Pin) SIP10 (STA10Pin) SIP10 (STA10Pin) SIP10 (STA10Pin) SIP10 (STA10Pin) SIP10 (STA10Pin) SIP10 (STA10Pin)
Transistors
171
General-Purpose
Part Number STA303A STA412A STA473A SMA4030 STA403A SLA4030 SLA5037 SLA4060 STA404A SLA5041 SLA5085 Circuit Count 3 4 4 4 4 4 4 4 4 4 5 VCEO (V)/ VDSS (V) 100 60 100 100 100 100 100 120 200 200 60 IC (A)/ ID (A) 4 3 2 3 4 4 10 5 3 10 5 2000 1000 0.175 0.22 hFE (min) 100 300 2000 2000 1000 2000 0.08 RDS(ON)max () Equivalent Circuit 12 13 17 15 17 15 14 15 17 14 16 Package SIP8 (STA8Pin) SIP10 (STA10Pin) SIP10 (STA10Pin) SIP12 (SMA12Pin) SIP10 (STA10Pin) SIP12 with Fin (SLA12Pin) SIP12 with Fin (SLA12Pin) SIP12 with Fin (SLA12Pin) SIP10 (STA10Pin) SIP12 with Fin (SLA12Pin) SIP12 with Fin (SLA12Pin)
172
Transistors
A
21
11
13
15
17
19
10
12 1, 20
14
16
18
Transistors
173
General-Purpose
Part Number STA322A STA302A STA402A STA472A STA421A SMA4020 SLA4070 STA408A SLA5086 Circuit Count 3 3 4 4 4 4 4 4 5 VCEO (V)/ VDSS (V) 50 50 50 60 60 60 100 120 60 IC (A)/ ID (A) 3 4 4 2 3 4 5 4 5 hFE (min) 100 1000 1000 2000 40 2000 1000 2000 0.22 RDS(ON)max () Equivalent Circuit 2 3 4 4 6 5 5 7 8 Package SIP8 (STA8Pin) SIP8 (STA8Pin) SIP10 (STA10Pin) SIP10 (STA10Pin) SIP10 (STA10Pin) SIP12 (SMA12Pin) SIP12 with Fin (SLA12Pin) SIP10 (STA10Pin) SIP12 with Fin (SLA12Pin)
174
Transistors
7 2
3 8
Transistors
175
176
Transistors
Transistors
177
178
Transistors
Transistors
179
IC(A) 30 30
RDS(ON) max()
Equivalent Circuit 1 2
180
Transistors
Transistors
181
SLA4071 SMA4021
STA322A STA421A
182
Transistors
Part Number Applications DC Motor Typical Connection Diagram Transistors Darlington Normal/Reverse Rotation Control STA434A STA457C STA4390 Single STA431A STA474A MOS FETs
PWM Control
SLA5022 SMA5130
Transistors
183
Part Number Applications Stepping Motor Typical Connection Diagram Transistors Darlington Constant Voltage Driver STA401A STA406A STA435A STA471A STA475A STA481A STA485A SLA4010 SDC04 SDC03 SMA6511 Single STA460C STA413A SDC06 MOS FETs
Bipolar Driver
STA473A STA472A STA408A STA404A STA403A STA402A SMA4030 SMA4020 SLA4070 SLA4060 SLA4030
Part Number Applications 5-Phase Motor Typical Connection Diagram N-CH SLA5065+SLA5068 SLA5073+SLA5074 SLA5085 SLA5086 P-CH
184
Transistors
TO-220F (FM20)
10.00.2
4.0 0.3
TO-220 (MT-25)
2.80.2 (1.7)
TO-3P (MT-100)
15.6 0.3
4.50.2 1.30.2
(1.3)
2.0
9.90.3 (8.7)
9.6 0.2
5.0 0.7
18.95MAX
15.90.3
0.8 0.2
a b
3.30.2
(3)
a b
2 +0.2 0.1 3 +0.2 0.1 1.05+0.2 0.1 5.45 0.1 E
2.4
13.10.5
0.2
13.0min
1.350.15 1.350.15 0.85+0.2 0.1 2.54 2.54 2.20.2 0.45+0.2 0.1 2.40.2
100.2
20.0min 3.5
3.9
0.2
0.5 0.1
0.15
2.540.2
5.45 0.1 B
TO-3PF (FM100)
5.50.2 3.450.2
MT-200
36.4 0.3 6.0 0.2 2.1 9
7
TO-220S
24.4 0.2
(1.4)
15.60.2
2- 3.2 0.1
3.2 0.1
4.440.2
3.60.2
9.20.3
19.90.3 4.0
0.8
5.5
0.2
10.20.3
1.30.2
21.40.3
1.6
b
2 3 1.05 +0.2 0.1 5.45 0.1 B C E 5.45 0.1 0.6 +0.2 0.1 3.0 +0.3 0.1
1.270.2
(1.5)
a b
3.30.2
3.0
b c
(1.5) 8.60.3
10.0 0.5
+0.3
0.1 0.1
+0.2
2.590.2
+0.3
3.3
1.750.15 2.150.15 1.05+0.2 0.1 5.450.1 1.5 4.4 5.450.1 1.5 0.65+0.2 0.1
0.8
20.0min
4.1max
1.20.2 2.540.5
q w e
3.0 0.5
0.86 0.1
+0.2
3.350.2
2.540.5 10.2+0.3
TO-263
1.200.20 (0.40)
9.900.20 4.500.20 1.30 +0.10 0.05
TO3P-5Pin
NPN
Gate burr (Including pulling out the burr)
PNP
Gate burr (Including pulling out the burr)
9.200.20
15.300.30
1.400.20
0.100.15
(0.75) 2.000.10
4.900.20
1.270.10 2.540.20
0.800.10 2.540.20
2.540.30
2.400.20 (R0.30)
(Unit : mm)
Transistors
185
SIP 8 (STA8Pin)
20.4 max
SIP 10 (STA10Pin)
25.250.2
11.30.2
9.00.2
2.30.2
9.00.2
b a
4.70.5
4.70.5
1.00.25
0.50.15
(2.54)
1.00.25
0.50.15
0.50.15
(2.54)
C1.50.5
9 2.54 = 22.860.25
7 P2.54 = 17.78
1.20.2
C1.50.5
4.00.2
1 E
2 3 4 5 6 7 B C B C B C
8 9 10 B C E
Pin No.
PS 16 (Surface-Mount)
0.890.15
+0.15 0.750.05
SIP 12 (SMA12Pin)
2.540.25 9 16
6.8max
31.00.2
4.00.2 2.50.2
a b
1 20.0max 19.560.2 8
10.20.2
b
2.4
8.00.5 6.3
0.25
0.2
0.30.05
+0.15
(10.4)
4.0max
1.00.3
3.00.2 9.80.3
3.60.2 1.40.2
0 to 0.1
0.550.1
+0.2
1.20.1
SIP 15 (SMA15Pin)
31.0
0.2
10.20.2
b a
(3.0) 6.70.5
9.70.5
16.00.2
+1.0
13.00.2
R-End
a b
9.5min
0.650.1
+0.2
1.150.1
+0.2
2.7
0.550.1
+0.2
* 4.00.7
Pin1
12 0.850.1
+0.2 +0.2
14 P2.030.7= 28.421.0
1.20.15 11 P2.54 1.450.15
0.7
0.550.1
1.0
2.20.7
= 27.94
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
3.20.15
3.20.15 3.8
4.80.2 1.70.1
4.8
0.2
1.70.1
3.20.15
Gate burr
16.00.2
12.90.2
160.2
9.9 13.00.2
a
2.450.2
(3.0) 6.70.5
17.90.6 (5)
0.2
9.90.2
2.450.2
4(R1)
9.70.5
+1.0
R-End
0.650.1
30.5
+0.2
20 P1.430.5=28.61.0
+0.2 0.1
0.550.1 40.7
+0.2
0.65
+0.2 0.1
14 P2.030.7=28.421.0
1.15
+0.2 0.1
0.55
31.30.2
* 4.00.7
a: Part Number b: Lot No.
1 2 3 4 5 6 7 9 11 13 15 17 19 21 8 10 12 14 16 18 20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
(Unit:mm)
186
Transistors
Thyristors
Ordering Information & Standard Packing Quantities .............. 188 Application Note ............................................................................... 189 3-1 3-2 Thyristors ............................................................................... 190 Triacs ...................................................................................... 192
3 Thyristors
Ordering Information
All products listed must be ordered in standard packing increments.
Product Name SLA0201 STA203A TFC563D TF361H-A TF541S-A TF561S-A TFA37S TFA38S TFA57S TFA58S TFA87S TFA88S TFA107S TFA108S TMA104S-L TMA106G-L TMA106H-L TMA106S-L TMA124S-L TMA126G-L TMA126H-L TMA126S-L TMA164B-L TMA164P-L TMA164S-L TMA166B-L TMA166G-L TMA166H-L TMA166P-L TMA166S-L TMA204S-L TMA206S-L TMA254B-L TMA256B-L TMA34S-L TMA36G-L TMA36H-L TMA36S-L TMA54S-L TMA56G-L TMA56H-L TMA56S-L TMA84S-L TMA86G-L TMA86H-L TMA86S-L TMB166S-L TMB206S-L Package SLA12Pin STA8Pin TO220S(Straight) TO220F-A TO220F TO220F TO220F TO220F TO220F TO220F TO220F TO220F TO220F TO220F TO220F TO220 TO220F-A TO220F TO220F TO220 TO220F-A TO220F TO3PF TO3P TO220F TO3PF TO220 TO220F-A TO3P TO220F TO220F TO220F TO3PF TO3PF TO220F TO220 TO220F-A TO220F TO220F TO220 TO220F-A TO220F TO220F TO220 TO220F-A TO220F TO220F TO220F Standard Packing Quantities (Bulk) 1080(Stick) 1000(Box)/4050(Stick) 600(Stick) 4000(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 4000(Stick) 4000(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 4000(Stick) 4000(Stick) 1000(Box)/3750(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 1000(Box)/3750(Stick) 500(Box)/1080(Stick) 4000(Stick) 4000(Stick) 500(Box)/1080(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 500(Box)/1080(Stick) 500(Box)/1080(Stick) 1000(Box)/3750(Stick) 4000(Stick) 4000(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 4000(Stick) 4000(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 4000(Stick) 4000(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick) 1000(Box)/3750(Stick)
188
Thyristors
3 Thyristors
Application Note
Since reliability can be affected adversely by improper storage environment or handling methods during Characteristic tests, please observe the following cautions.
Heatsink
A larger contact area between the device and the heatsink is required for more effective heat radiation. To ensure a larger contact area, minimize mounting holes. And select a heatsink with a surface smooth enough and free from burrs and slivers.
Soldering Temperature
In general, the device mounted on a printed circuit board is subjected to high temperatures from flow solder in a solder bath, or, from a soldering iron at hand soldering. The testing method and test conditions (JIS-C-7021 standards) for a devices heat resistance to soldering are: At a distance of 1.5mm from the device's main body, apply 260C for 10 seconds, and 350C for 3 seconds. Please observe these limits and finish soldering in as short a time as possible. Since reliability can be affected adversely by improper storage environment or handling methods during Characteristic tests, please observe the following cautions.
Silicone Grease
When using a heatsink, please coat thinly and evenly the back surface of the device and both surfaces of the insulating plate with silicone grease to lower the thermal resistance between the device and the heatsink. Please select proper silicone grease carefully since the oil in some grease products may penetrate the device and result in an extremely short device life. Recommended Silicone Grease G-746 (Shin-Etsu Chemical) YG6260 (Momentive Performance Materials Inc.) SC102 (Dow Corning Toray Silicone)
Mounting Torque
When mounting torque is insufficient, thermal resistance increases, and so heat radiation effect is decreased. When the torque is excessive, the screw may be broken, the heatsink may be deformed, and the device frame may be distorted, resulting in the device damage. Recommended mounting torque per package is as follows: Mounting Torque Table
Package TO220 TO220F-A, TO220F (FM20) TO3P (MT100) TO3PF (FM100) SLA (SIP with Fin) Screw Torque 0.490 to 0.686 Nm (5 to 7kgfcm) 0.686 to 0.882 Nm (7 to 9kgfcm) 0.588 to 0.784 Nm (6 to 8kgfcm)
* When the surface of a heatsink where Full Mold package is to be mounted is not flat due to the burred metal bracket for screwing around the mounting hole of the heatsink, the resin of the package might be cracked even if the torque is lower than the recommended value. * When a screw is fastened with an air driver for the Full Mold package, a large impact is generated at the time of stop, and the resin may crack even if the torque is lower than the recommended value. An electric driver, therefore, should be used instead of an air driver.
Thyristors
189
3-1 Thyristors
Thyristors
Absolute Maximum Ratings V RSM V DSM (V) TF541S-A SLA0201 TF361H-A TF561S-A TFA37S TFA57S TFA87S TFA107S TFA38S TFA58S TFA88S TFA108S
*1:Default Tj=110C
Part Number
V RRM V DRM (V) 400 600 600 600 700 700 700 700 800 800 800 800
(A) 5.0 5 4 3.0 5.0 3.0 5.0 8.0 10 3.0 5.0 8.0 10
ITSM 50Hz Single Half Sine Wave, Default T j =125C (A) 80 80 *1 60 80 60 80 120 160 60 80 120 160
P GM
P G (AV)
V RGM
IFGM
Tj
T stg
(W) 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0
(W) 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
(V) 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0
(C)
( C)
I RRM I DRM Conditions Tj (mA) (C) max 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 125 125 125 125 150 150 150 150 150 150 150 150
40 to +125 40 to +125
83 88 127 115 98 86 50 50 50 50
4.7 7.8 4.7 7.8 12.6 15.7 4.7 7.8 12.6 15.7
2.0 40110 40125 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 40 to +125 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150
40 to +125
*1: TC100C, VD430V, Wp1.0s, IG70mA, dig/dt0.5A/s, 100kcycles *2: TC100C, VD430V, Wp1.0s, 100kcycles
190
Thyristors
3-1 Thyristors
Electrical Characteristics V TM Conditions I TM Tc ( C) (A) typ 25 25 25 25 25 25 25 25 25 25 25 25 10 10 5.0 10 10 15 20 20 10 15 20 20 0.7 V GT IGT Conditions Tc (C) 25 25 25 25 25 25 25 25 25 25 25 25 VGD Tj (C) 125 125 125 125 125 125 125 125 125 125 125 125 dv/d t Conditions Conditions VD Tj (V) (V/ s) ( C) typ 1/2V DRM 1/2V DRM 1/2VDRM 1/2V DRM 1/2VDRM 1/2VDRM 1/2VDRM 1/2VDRM 1/2VDRM 1/2VDRM 1/2VDRM 1/2VDRM 20 50 50 20 300 300 300 300 300 300 300 300 125 125 110 125 125 125 125 125 125 125 125 125 IH VD (V) 1/2V DRM 1/2V DRM 1/2VDRM 1/2V DRM 1/2VDRM 1/2VDRM 1/2VDRM 1/2VDRM 1/2VDRM 1/2VDRM 1/2VDRM 1/2VDRM Rth Package (mA) typ 4.0 4.0 4.0 15 15 20 20 15 15 20 20 5 4.0 4.1 3.8 3.5 3.4 4.1 3.8 3.5 3.4 (C/W) max 4.0 TO220F SIP12 with Fin (SLA12Pin) 1.4 1.4 1.5 1.5 1.4 1.35 1.5 1.5 1.5 1.35 1.5 1.5 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 0.03 7.0 7.0 7.0 7.0 0.1 0.2 15 15 15 15 15 15 15 15 0.1 0.1 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 TO220F-A TO220F TO220F TO220F TO220F TO220F TO220F TO220F TO220F TO220F 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 g Mass
0.03 5.0
2.0 6.0
Electrical Characteristics V GT I GT Conditions Tc (C) 25 VGD Conditions (V) min 0.1 Tj (C) 125 VD (V) 480 (mA) typ 12 (C/W) max 4.0 (V) max 1.4 IH Rth VF Conditions IF (A) 10 Package (g) TO-220S 1.5 Mass
(mA) max 30
Thyristors
191
3-2 Triacs
Triacs
Absolute Maximum Ratings ITSM PGM PG (AV) Conditions Conditions Tc (C) (A) (W) (W)
IT (RMS)
I GM
Tj
T stg
I DRM1 Conditions
V TM Conditions I TM (A)
(A)
(A)
(C)
( C)
(mA) max 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1
(V) max 1.5 1.5 1.5 1.5 1.5 1.45 1.4 1.4 1.4 1.3 1.6 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.45 1.45 1.45 1.4 1.4 1.45 1.4 1.4 1.3
TMA34S-L TMA54S-L TMA84S-L TMA104S-L TMA124S-L TMA164S-L TMA164P-L TMA164B-L TMA204S-L TMA254B-L STA203A TMA36S-L TMA36G-L TMA36H-L TMA56S-L TMA56G-L TMA56H-L TMA86S-L TMA86G-L TMA86H-L TMA106S-L TMA106G-L TMA106H-L TMA126S-L TMA126G-L TMA126H-L TMA166S-L TMA166G-L TMA166H-L TMA166P-L TMA166B-L TMB166S-L TMA206S-L TMB206S-L TMA256B-L
400 400 400 400 400 400 400 400 400 400 400 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600
3 5 8 10 12 16 16 16 20 25 1.23 3 3 3 5 5 5 8 8 8 10 10 10 12 12 12 16 16 16 16 16 16 20 20 25
109 102 92 85 77 66 108 98 53 83 97 109 115 109 102 111 101 92 107 91 85 105 83 77 103 78 66 100 65 108 98 94 53 85 83
30 50 80 100 120 160 160 160 190 250 10 30 30 30 50 50 50 80 80 80 100 100 100 120 120 120 160 160 160 160 160 160 190 200 250
125 125 125 125 125 125 125 125 125 125 125 125 25 25 125 25 25 125 25 25 125 25 25 125 25 25 125 25 25 125 125 125 125 125 125
3 5 5 5 5 5 5 5 5 5 1.2 3 3 3 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5
0.3 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.1 0.3 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +125 40 to +150 40 to +125 40 to +150 40 to +125
192
Thyristors
3-2 Triacs
Electrical Characteristics (T j = 25 C, unless otherwise specified) V GT IGT V GD Mode I Mode II Mode III Conditions Mode I Mode III Conditions Mode II Conditions (T2+, G+) (T2+, G) (T2, G) V D RL (T2+, G+) (T2+, G) (T2, G) VD R L VO Tj (V) () (V) () (V) (V) (V) (mA) (mA) (mA) (C) (V) max max max max max max 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 3.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.2 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.2 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 12 12 12 12 12 12 12 12 12 12 6 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 20 20 20 20 20 20 20 20 20 20 10 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 30 30 30 30 30 30 30 30 3 15/20 30 30 15/20 30 30 20/30 30 30 20/30 30 30 20/30 30 30 20/30 30 30 30 30 30 20/30 30 30 20 20 30 30 30 30 30 30 30 30 3 15/20 30 30 15/20 30 30 20/30 30 30 20/30 30 30 20/30 30 30 20/30 30 30 30 30 30 20/30 30 30 20 20 30 30 30 30 30 30 30 30 3 15/20 30 30 15/20 30 30 20/30 30 30 20/30 30 30 20/30 30 30 20/30 30 30 30 30 30 20/30 30 30 12 12 12 12 12 12 12 12 12 12 6 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 20 20 20 20 20 20 20 20 20 20 10 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.1 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM 0.2 125 1/2VDRM
(dv/dt) c R th (j-c) Conditions Package (dv/dt) c T j (V/us) (A/ms) (C) ( C/W) max min 5 5 10 10 10 10 10 10 10 10 1 5 5 5 5 5 5 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 1.5 125 2.5 125 4 125 5 125 6 125 8 125 8 125 8 125 10 125 12 125 125 1.5 125 1.5 125 1.5 125 2.5 125 2.5 125 2.5 125 4 125 4 125 4 125 5 125 5 125 5 125 6 125 6 125 6 125 8 125 8 125 8 125 8 125 8 125 10 125 10 125 10 125 12 125 4.5 4 3.7 3.6 3.5 3.3 1.2 1.8 3.2 1.6 20 4.5 3 4.6 4 2.5 4.2 3.7 2 3.8 3.6 1.8 3.7 3.5 1.6 3.5 3.3 1.4 3.3 1.2 1.8 3.0 3.2 2.7 1.6 TO220F TO220F TO220F TO220F TO220F TO220F TO3P TO3PF TO220F TO3PF STA8pin TO220F TO220 TO220F-A TO220F TO220 TO220F-A TO220F TO220 TO220F-A TO220F TO220 TO220F-A TO220F TO220 TO220F-A TO220F TO220 TO220F-A TO3P TO3PF TO220F TO220F TO220F TO3PF
Mass
(g) 2.0 2.0 2.0 2.0 2.0 2.0 6.0 6.5 2.0 6.5 2.0 2.0 2.5 2.0 2.0 2.5 2.0 2.0 2.5 2.0 2.0 2.5 2.0 2.0 2.5 2.0 2.0 2.5 2.0 6.0 6.5 2.0 2.0 2.0 6.5
Thyristors
193
TO-220
9.90.3 (8.7)
2.80.2
TO-220F-A
4.50.2 1.30.2
TO-220F
(1.3)
9.20.3
15.90.3
15.80.2
3.60.2
18.95MAX
15.870.3
16.9 0.3
8.4 0.2
3.20.2
6.680.2
4.0 0.2
10.160.3
2.540.2
10.00.2
(1.7)
3.30.2
(3)
2.40.2
9.750.5
2.760.2 0.8
0.1
a b
13.10.5
13.0min
2.540.2 10
0.2
2.54
0.2
4.70.2
(1) (2) (3)
2.54 2.2
0.2
3.9
0.5 0.1
0.15
0.5 0.1
0.8 0.2
2.40.2
(1)(2)(3)
TO-3P
5.0 0.7 2.0 15.6 0.3 13.6 0.2 9.6 0.2 4.8 0.2 2.0 0.1
TO-3PF
5.50.2
TO-220S Straight
(5)
(1.4)
3.20.2
5.50.2 3.450.2
9.50.2
4.440.2 1.30.2
1.8
230.3
19.90.3 4.0
(0.45)
3.2 0.1
10.5
a b
2 +0.2 0.1 3 +0.2 0.1 1.05+0.2 0.1 5.45 0.1
a b
9.10.3
1.6 3.3
+0.3 -0.5
20.0min 3.5
1.34 -0.1
+0.2 +0.2
5.45 0.1
0.65 0.1
0.760.1
110.5
+0.2
0.86 -0.1
(2.69) (1.8)
+0.2
(16.2)
2.540.1
(Measured at the root)
2.540.1
(Measured at the root)
0.40.1
10.20.3
STA8Pin
20.2 0.2 400.20.2
SLA12Pin
3.20.15
11.3 0.2
b a
a b
4.7 0.2
0.8max
Thy1 12 +0.2 0.85 0.1 +0.2 1.450.15 0.55 0.1 11P2.540.7=27.940.1 31.5max
Thy2
Thy3
Thy4
Pin 1
2.54
1.20.15
2.2 0.7
1 2 3 4 1 5 6 7 8 9 10 11
0.5 0.15
3 TR1 2 1 TR2 4
7 TR3 6
1.2 0.2
T1 G T2 G T2 G T2 T1
1 2 3 4 5 6 7 8 9 10 11 12 G K A G K A G K A G K A
(Unit: mm)
194
Thyristors
Diodes
Ordering Information & Standard Packing Quantities .............. 196 Taping Specifications ...................................................................... 198 Application Note ............................................................................... 201 Marking Guide ................................................................................... 202 4-1 Rectifier Diodes .................................................................... 203 Surface-Mount ........................................................................ 203 Thru-Hole ................................................................................ 203 4-2 4-3 Fast Recovery Diodes ......................................................... 204 Thru-Hole ................................................................................ 204 Ultrafast Recovery Diodes .................................................. 206 Surface-Mount ........................................................................ 206 Thru-Hole ................................................................................ 206 4-4 Schottky Barrier Diodes ...................................................... 209 Standard .................................................................................. 209 Surface-Mount ................................................................. 209 Thru-Hole ......................................................................... 209 Low VF A Series .................................................................. 210 Surface-Mount ................................................................. 210 Thru-Hole ......................................................................... 210 Low IR E Series ................................................................... 211 Surface-Mount ................................................................. 211 Thru-Hole ......................................................................... 211 Low VF/Low IR Balance J Series ....................................... 211 Surface-Mount ................................................................. 211 Thru-Hole ......................................................................... 211 4-5 4-6 Power Zener Diodes ............................................................. 212 Silicon Varistors ................................................................... 213
4 Diodes
Ordering Information
All products listed must be ordered in standard packing increments.
Series Name/Product Name AG01x AK0x AL01x AM01x AP01x AS01x AU01x AU02x EG01x EK0x EL02x EM01x EN01x EP01x ES01x EU01x EU02x SVxx VR-xx EG1x EH1x EK1x EL1x EM1x EM2x ES1x EU1x EU2x RA1x RC2 RF1x RG10x RG1x RH1x RK1x RL10x RM10x RM11x RM1x RN1x RP1x RS1x RU1x RU20x RU2x RX10x RD2x RG2x RH2x RK3x RL2x RM2x RN2x RO2x RU3x RG4x RH4x RJ4x RK4x RL4x RM4x RN4x RS4x RU4x RW5x Package Axial(2.4 body/ 0.6 lead) Axial(2.4 body/ 0.6 lead) Axial(2.4 body/ 0.6 lead) Axial(2.4 body/ 0.6 lead) Axial(2.4 body/ 0.6 lead) Axial(2.4 body/ 0.6 lead) Axial(2.4 body/ 0.6 lead) Axial(2.4 body/ 0.6 lead) Axial(2.7 body/ 0.6 lead) Axial(2.7 body/ 0.6 lead) Axial(2.7 body/ 0.6 lead) Axial(2.7 body/ 0.6 lead) Axial(2.7 body/ 0.6 lead) Axial(2.7 body/ 0.6 lead) Axial(2.7 body/ 0.6 lead) Axial(2.7 body/ 0.6 lead) Axial(2.7 body/ 0.6 lead) Axial(2.7 body/ 0.6 lead) Axial(2.7 body/ 0.6 lead) Axial(2.7 body/ 0.78 lead) Axial(2.7 body/ 0.78 lead) Axial(2.7 body/ 0.78 lead) Axial(2.7 body/ 0.78 lead) Axial(2.7 body/ 0.78 lead) Axial(2.7 body/ 0.78 lead) Axial(2.7 body/ 0.78 lead) Axial(2.7 body/ 0.78 lead) Axial(2.7 body/ 0.78 lead) Axial(4.0 body/ 0.78 lead) Axial(4.0 body/ 0.78 lead) Axial(4.0 body/ 0.78 lead) Axial(4.0 body/ 0.78 lead) Axial(4.0 body/ 0.78 lead) Axial(4.0 body/ 0.78 lead) Axial(4.0 body/ 0.78 lead) Axial(4.0 body/ 0.78 lead) Axial(4.0 body/ 0.78 lead) Axial(4.0 body/ 0.78 lead) Axial(4.0 body/ 0.78 lead) Axial(4.0 body/ 0.78 lead) Axial(4.0 body/ 0.78 lead) Axial(4.0 body/ 0.78 lead) Axial(4.0 body/ 0.78 lead) Axial(4.0 body/ 0.78 lead) Axial(4.0 body/ 0.78 lead) Axial(4.0 body/ 0.78 lead) Axial(4.0 body/ 0.98 lead) Axial(4.0 body/ 0.98 lead) Axial(4.0 body/ 0.98 lead) Axial(4.0 body/ 0.98 lead) Axial(4.0 body/ 0.98 lead) Axial(4.0 body/ 0.98 lead) Axial(4.0 body/ 0.98 lead) Axial(4.0 body/ 0.98 lead) Axial(4.0 body/ 0.98 lead) Axial(6.5 body/ 1.4 lead) Axial(6.5 body/ 1.4 lead) Axial(6.5 body/ 1.4 lead) Axial(6.5 body/ 1.4 lead) Axial(6.5 body/ 1.4 lead) Axial(6.5 body/ 1.4 lead) Axial(6.5 body/ 1.4 lead) Axial(6.5 body/ 1.4 lead) Axial(6.5 body/ 1.4 lead) Axial(6.5 body/ 1.4 lead) 500 500 500 500 500 500 500 500 500 500 Standard Packing Quantities Bulk V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:5000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V:3000(Reel) V1:3000(Box) V1:3000(Box) V1:3000(Box) V1:3000(Box) V1:3000(Box) V1:3000(Box) V1:3000(Box) V1:3000(Box) V1:2000(Box) V1:2000(Box) V1:2000(Box) V1:2000(Box) V1:2000(Box) V1:2000(Box) V1:2000(Box) V1:2000(Box) V1:2000(Box) V1:2000(Box) V1:2000(Box) V1:2000(Box) V1:2000(Box) V1:2000(Box) V1:2000(Box) V1:2000(Box) V1:2000(Box) V1:2000(Box) V1:2000(Box) V1:2000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) V1:1000(Box) Taping V0:3000(Box) V0:3000(Box) V0:3000(Box) V0:3000(Box) V0:3000(Box) V0:3000(Box) V0:3000(Box) V0:3000(Box) V0:2000(Box) V0:2000(Box) V0:2000(Box) V0:2000(Box) V0:2000(Box) V0:2000(Box) V0:2000(Box) V0:2000(Box) V0:2000(Box) V0:2000(Box) V0:2000(Box) V0:2000(Box) V0:2000(Box) V0:2000(Box) V0:2000(Box) V0:2000(Box) V0:2000(Box) V0:2000(Box) V0:2000(Box) V0:2000(Box) WS:2500(Box) WS:2500(Box) WS:2500(Box) WS:2500(Box) WS:2500(Box) WS:2500(Box) WS:2500(Box) WS:2500(Box) W:4000(Box) W:4000(Box) W:4000(Box) W:4000(Box) W:4000(Box) W:4000(Box) W:4000(Box) W:4000(Box) W:4000(Box) W:4000(Box) W:4000(Box) WK:2500(Box) WK:2500(Box) WK:2500(Box) WK:2500(Box) WK:2500(Box) WK:2500(Box) WK:2500(Box) WK:2500(Box)
196
Diodes
4 Diodes
Series Name/Product Name SPB-x SPX-xxx SJPA-xx SJPB-xx SJPE-xx SJPJ-xx SJPL-xx SJPM-xx SJPW-xx SJPX-xx SJPZ-xx SZ-10xx FMC-2xU FM2-2202 FMB-2x FME-2x FMEN-2x FMG-1x FMG-2x FMJ-2x FML-1x FML-2x FMM-2x FMU-1x FMU-2x FMW-2x FMX-1x FMX-2x FMXA-2x FMXB-2x FMXJ-2x FMB-G1x FMB-G2x FMC-G2x FMD-G2x FMG-G2x FML-G1x FML-G2x FMN-G1x FMP-G1x FMQ-G1x FMQ-G2x FMU-G1x FMU-G2x FMXA-1x FMX-G1x FMX-G2x FMC-2xUA MPE-2x MPL-102S MPEN-2x MPL-1036S FMD-4x FMXA-4x FML-4x FMP-G5x FMQ-G5x FMR-G5x FMV-G5x
Package D pack(Surface-mount) D pack(Surface-mount) SJP SJP SJP SJP SJP SJP SJP SJP SJP SZ-10(Surface-mount) TO220F(2-element) TO220F(Center-tap) TO220F(Center-tap) TO220F(Center-tap) TO220F(Center-tap) TO220F(Center-tap) TO220F(Center-tap) TO220F(Center-tap) TO220F(Center-tap) TO220F(Center-tap) TO220F(Center-tap) TO220F(Center-tap) TO220F(Center-tap) TO220F(Center-tap) TO220F(Center-tap) TO220F(Center-tap) TO220F(Center-tap) TO220F(Center-tap) TO220F(Center-tap) TO220F-2Pin TO220F-2Pin TO220F-2Pin TO220F-2Pin TO220F-2Pin TO220F-2Pin TO220F-2Pin TO220F-2Pin TO220F-2Pin TO220F-2Pin TO220F-2Pin TO220F-2Pin TO220F-2Pin TO220F-2Pin TO220F-2Pin TO220F-2Pin TO220F-2Pin(2-element) TO220S(Surface-mount) TO220S(Surface-mount) TO263(Surface-mount) TO220S(Surface-mount) TO3PF(Center-tap) TO3PF(Center-tap) TO3PF(Center-tap) TO3PF-2Pin TO3PF-2Pin TO3PF-2Pin TO3PF-2Pin 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500
Standard Packing Quantities Bulk VL:3000(Reel) VL:3000(Reel) V:1800(Reel) V:1800(Reel) V:1800(Reel) V:1800(Reel) V:1800(Reel) V:1800(Reel) V:1800(Reel) V:1800(Reel) V:1800(Reel) VL:750(Reel) VR:1000(Reel) VR:1000(Reel) VL:800(Reel) VL:800(Reel) VR:800(Reel) VR:800(Reel) VR:750(Reel) VR:3000(Reel) VR:3000(Reel) Taping
Diodes
197
4 Diodes
Taping Specifications
Taping Name Axial taping Taping Type, Dimensions (mm) Packing Dimensions (mm) and Packing Note Reel
0.5max 1.0 ---1.0
+ 0.5
Quantity
5.08 + 0.38
29 1 75 1
V
To specify the taping type, add a suffix [V]
(Blue)
15
Core Flange
83 2
0.5 max
6.0
+ 0.5
0
52.0
+1
0
(White)
6.0
+ 0.5
0
25 0.1 75 2
Holddown clip
0.5max
812
Axial taping
V1
To specify the taping type, add a suffix [V1]
0.5 max
(Blue)
2,000 pcs/box (2.7 body) 3,000 pcs/box (2.4 body) 1,000 pcs/box (4 body)
(White)
5.08 + 0.38
6.0
+ 0.5
0
52.0
+1
0
6.0
+ 0.5
0
255max
a 77m
0.5max
Axial taping
V0
To specify the taping type, add a suffix [V0]
0.5 max
(Blue)
5.08 + 0.38
(White)
6.0
+ 0.5
0
26.0
+1
0
6.0
+ 0.5
0
255max
51m
ax
0.5max
198
Diodes
95max
4 Diodes
Quantity
140max
1.0 1.0
3.0 max
W
To specify the taping type, add a suffix [W]
9.00.5 12.5min
ANODE
18.0 0.5
+1.0
1.0 max
3.85 0.7
4.0 0.2
0.70.2
340max
WS
To specify the taping type, add a suffix [WS]
0 2.0
18.0 0 11max
0.7 0.2
3.850.7
+0.8
4.0 0.2
55m ax
Part No., Lot No., Quantity
(5.5)
--1 0+
--1 0+
(30)
1max
-- 1.0 19.8 +
- 0.5 16.5 --
--1 22.2 +
+ 1.0
WK
To specify the taping type, add a suffix [WK]
1.5
-- 0.5 2.75+
11max
340max
4.0 + -- 0.2
-- 0.2 3.0 +
0.8 5+ -- 0.2
-- 0.7 3.85+
-- 0.2 0.52 +
45m
ax
E CATHOD
ANODE
150max
ODE CATH
Diodes
199
4 Diodes
Quantity
Emboss Taping
1.5 +0.1 0
40.1
Feeding Direction
2.150.2
SJP
VL VR
To specify the taping type, add a suffix [VL] or [VR]
4.50.2
20.05
12 +0.3 0.1
5.50.05
2.00.5 130.5
5.60.1
2.60.2
602
1.30.4 1.50.2
R1.0 210.8
1800 pcs/reel
(1) Device is placed in the embossed pocket with the mounting electrode down. (2) 150 to 200mm leader tape is attached to the tip of the tape. (3) 10 or more blank pockets are provided at both the beginning and the end of the tape.
180 +0 3
131.5
1.20.5
VL
To specify the taping type, add a suffix [VL]
Feeding Direction
Lot No.
1.750.1
0.1 1.5 + 0
4.0 0.1
8.0
0.1
3.4 max
R9
5 1
) (40
(1
D Pack
7.5 0.1
13.50.1 10.60.1
16.0 0.3
R401 40.5
20 )
(6.0)
6.8 0.1
0.1 1.6 + 0
23 max
VR
Feeding Direction
0.30.1
(2.0)
2.00.1
3000 pcs/reel
3000 pcs/reel
Feeding Direction
TO-220S
VR
2.00.1
1.750.1 11.50.1 21.05 0.1 13.90.1 24.0 0.3
(R
(2.0)
13
0)
) (40
(R5)
(R5)
(1
R501 40.5
20 )
(6.0)
0.1 1.5 + 0
4.0 0.1
12.0 0.1
4.9 max
1000 pcs/reel
10.8 0.1
3.0 max
0.40.1
31 max
Quantity
VL
4
35
1 3 B
1 3 B
11.500.1
750 pcs/reel
10
1.500.1
2.000.1
4.000.1
1.750.1
5.640.1
10
22
3302
1001
24.000.1
16.000.1
120
130.2
+0.3
80
60
40
20
25.51 29.51
VR
To specify the taping type, add a suffix [VR]
R135
Feeding Direction
R TYPE L TYPE
16.000.1 10.800.1
1.500.25
0.400.05
90.5
7 0.5
750 pcs/reel
20.5
21
0.8
Label the Part No., Quantity, Lot No. and seal it on the reel
5 0.
13
130.5
2 0.
200
Diodes
4 Diodes
Application Note
General Description
(1) Lead Forming When forming leads, hold the lead wire on the main body's side so as to prevent stress from being applied to the main body.
Surface-Mount Diodes
(Part Number Type: SJP) Soldering (common to flow and reflow)
i) Use rosin based flux. Never use acidic fluxes. ii) To prevent a large thermal stress, preheat within 1 to 2 minutes at 150C and solder within the usable range shown below.
Bend
(2) Mounting To mount a frame-type diode on a heatsink, use its screw hole. Do not fix its resin body as the silicon chip may get broken. (3) Temperature Measurement For an axial type diode, measure the temperature of the lead wire on the main body side. The thermocouple to be used must be as thin as possible (approximately 0.125mm). (4) Temperature Rise Consideration A diodes temperature increases due to losses from forward current, reverse current and reverse recovery time. In normal use, losses are mainly attributable to forward current and voltage. However, in high frequency circuits such as switching power supplies, losses due to reverse recovery time also occurs. Moreover, in diodes having large reverse currents like Schottky barrier diode losses due to reverse current cannot be disregarded. Forward loss tends to decrease at high temperatures. However, reverse loss tends to increase at high temperatures. Therefore, it is necessary to consider the ambient temperature when verifying operation. (5) Inrush Current In a capacitor-input type rectifier circuit, inrush current flows when the power supply is switched on. The peak value of this inrush current shall be set less than peak forward surge current IFSM (I2t can also be obtained but set the minimum pulse width to 1 msec). The value of IFSM is guaranteed for a single shot only. If the inrush current is repeated within a short period of time, the derating has to be taken into account.
iii) For using a soldering iron, use the following references: Temperature of soldering iron tip: Lower than 300C (Power of the soldering iron: 30W or lower) The soldering tip must be as thin as possible. Soldering time: Less than 10 seconds
2.0
2.0
4.0 to 4.2
(6) Peak Value Current Considering normal use, limit of the peak value current must be set to 10 times of the average current IF (AV). If the peak value increases. the diode's forward loss also increases. In this case, check the temperature rise.
Carefully study the mounting method when the usage environment is prone to creeping discharge.
2.0
Diodes
201
Usable Range
Bend
300
4 Diodes
Marking Guide
1 Axial (A0) 5 TO-3PF, FM100 type
qPart Number (abbreviation) The AM01 is indicated as M. wClass Z: 200V None: 400V A: 600V B: 800V C: 1000V eManufacturing date First letter: Year (Last digit of year) Second letter: Month (1 to 9, O, N, D) rCathode band: Continuous band Color of the band: White(Yellow for AU02 series) qPart Number: Full name wPolarity: Rectifier Symbol eLot No. First letter: Year (Last digit of year) Second letter: Month (1 to 9, O, N, D) Third and fourth letters: Day Laser marking or White ink marking
M A 9 D
FMXA4203
5905
MO C 87
qPart Number (abbreviation) EM01, EM2, EM1 are indicated as MO, M2 and M1, respectively. wClass Z: 200V None: 400V A: 600V B: 800V C: 1000V F: 1500V But EU02A is indicated as A2 and EU2YX as Y. eManufacturing date First letter: Year (Last digit of year) Second letter: Month (1 to 9, O, N, D) rManufacturing period First 10 days of month Middle 10 days of month Last 10 days of month
6905
6 Surface-Mount (SJP)
qPart Number
7 Surface-Mount (D pack)
B 64S
RK44 96
6H
qPart Number wPolarity: Rectifier Symbol eLot No. First letter: Lot code Second letter: Year (Last digit of year) Third letter: Month (A to M except I)
8 Surface-Mount (TO-220S)
E 29G
4 TO-220F type
FMU12S
8512
qPart Number FMU-12S is indicated as FMU12S. wPolarity: Rectifier Symbol eLot No. First letter: Year (Last digit of year) Second letter: Month (1 to 9, O, N, D) Third and fourth letters: Day Laser marking or White ink marking
9C1
qPart Number wPolarity: Rectifier Symbol eLot No. First letter: Year (Last digit of year) Second letter: Month (A to M except I) Third letter: Week
9 SZ-10 Series
(1-chip type)
FMLG12
S 0125
qPart Number: Excluding last letter FML-G12S is indicated as FML-G12. wLast letter of Part Number ePolarity: Rectifier Symbol rLot No. First letter: Year (Last digit of year) Second letter: Month (1 to 9, O, N, D) Third and fourth letters: Day Laser marking or White ink marking
qPart Number wLot No. First letter: Year (Last digit of year) Second letter: Month (1 to 9, O, N, and D) Third letter: Day
10 Silicon Varistors
Refer to P213
202
Diodes
Tj (C)
Tstg (C)
IF (A) 2.0
Tj (C) 150
2.0
-40 to +150
Thru-Hole
VRM (V) IF (AV) (A)
Values in parentheses are for the products (Body Diameter/Lead Diameter) with heatsinks
Package Axial
Part Number EM 1Y RM 4Y AM01Z EM01Z EM 1Z RM 1Z RO 2Z RM 2Z RM 10Z RM 4Z FMM-22S, R AM01 EM01 EM 1 RM 1 EM 2 RO 2 RM 2 RM 10 RM 4 FMM-24S, R AM01A EM01A EM 1A RM 1A EM 2A RM 11A RM 2A RM 10A RM 4A RM 4AM FMM-26S, R RM 1B EM 1B EM 2B RO 2B RM 11B RM 2B RM 10B RM 1C EM 1C RO 2C RM 11C RM 2C RM 4C
IFSM (A) 50Hz Single Half Sine Wave 45 200 35 45 45 50 80 100 120 200 100 35 45 45 50 80 80 100 150 200 100 35 45 45 50 80 100 100 150 200 350 100 40 35 80 80 100 100 150 40 35 80 100 100 150
Tj (C)
Tstg (C)
VF (V) max 0.97 0.95 0.98 0.97 0.97 0.95 0.92 0.91 0.91 0.95 1.1 0.98 0.97 0.97 0.95 0.92 0.92 0.91 0.91 0.95 1.1 0.98 0.97 0.97 0.95 0.92 0.92 0.91 0.91 0.95 0.92 1.1 1.2 1.05 0.92 0.92 0.92 0.91 0.91 1.2 1.05 0.92 0.92 0.91 0.97
IF (A) 1.0 3.0 1.0 1.0 1.0 1.0 1.5 1.5 1.5 3.0 5.0 1.0 1.0 1.0 1.0 1.2 1.5 1.5 1.5 3.0 5.0 1.0 1.0 1.0 1.0 1.2 1.5 1.5 1.5 3.0 3.5 5.0 1.0 1.0 1.2 1.5 1.5 1.5 1.5 1.0 1.0 1.5 1.5 1.5 3.0
Rth(j-l) Rth(j-c) (C/W) 17 8.0 22 20 17 15 12 12 15 8.0 4.0 22 20 17 15 17 12 12 15 8.0 4.0 22 20 17 15 17 15 12 15 8.0 8.0 4.0 15 17 17 12 15 12 15 15 17 12 15 12 8.0
Mass (g) 0.3 1.2 0.13 0.2 0.3 0.4 0.61 0.6 0.4 1.2 2.1 0.13 0.2 0.3 0.4 0.3 0.61 0.6 0.4 1.2 2.1 0.13 0.2 0.3 0.4 0.3 0.4 0.6 0.4 1.2 1.2 2.1 0.4 0.3 0.3 0.61 0.4 0.6 0.4 0.4 0.3 0.61 0.4 0.6 1.2
1.0 100 3.0 1.0 1.0 1.0 1.0 200 1.2 1.2 1.5 3.0 10 1.0 1.0 1.0 1.0 400 1.2 1.2 1.2 1.2 3.0 10 1.0 1.0 1.0 1.0 1.2 600 1.2 1.2 1.2 3.0 3.2 10 0.8 1.0 1.2 800 1.2 1.2 1.2 1.2 0.8 1.0 1000 1.2 1.2 1.2 3.0
Axial(2.7/0.78) Axial(6.5/1.4) Axial(2.4/0.6) Axial(2.7/0.6) Axial(2.7/0.78) Axial(4.0/0.78) Axial(4.0/0.98) Axial(4.0/0.98) Axial(4.0/0.78) Axial(6.5/1.4) TO-220F(Center-tap) Axial(2.4/0.6) Axial(2.7/0.6) Axial(2.7/0.78) Axial(4.0/0.78) Axial(2.7/0.78) Axial(4.0/0.98) Axial(4.0/0.98) Axial(4.0/0.78) Axial(6.5/1.4) TO-220F(Center-tap) Axial(2.4/0.6) Axial(2.7/0.6) Axial(2.7/0.78) Axial(4.0/0.78) Axial(2.7/0.78) Axial(4.0/0.78) Axial(4.0/0.98) Axial(4.0/0.78) Axial(6.5/1.4) Axial(6.5/1.4) TO-220F(Center-tap) Axial(4.0/0.78) Axial(2.7/0.78) Axial(2.7/0.78) Axial(4.0/0.98) Axial(4.0/0.78) Axial(4.0/0.98) Axial(4.0/0.78) Axial(4.0/0.78) Axial(2.7/0.78) Axial(4.0/0.98) Axial(4.0/0.78) Axial(4.0/0.98) Axial(6.5/1.4)
-40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150
50 100(Ta) 50 100
50 100(Ta) 50 100(Ta) 500 50 50 50 50 50 50 50 100 150 100 100 100 100 100 150 100 150
Diodes
203
Package Axial
IFSM (A) Tj (C) 50Hz Single Half Sine Wave 15 15 15 35 30 25 15 15 20 70 30 40 15 15 15 15 20 30 30 25 15 15 20 20 50 50 70 30 40 15 15 15 20 35 20 30 25 15 15 20 20 20 50 50 50 50 50 30 30 40 40 180 180
Tstg (C)
VF (V) max 1.0 1.0 1.7 1.3 2.5 1.3 1.4 1.4 1.5 1.3 1.5 1.5 2.5 2.5 2.5 1.7 1.5 1.35 2.5 1.3 1.4 1.4 1.2 1.5 1.1 1.5 1.3 1.5 1.5 2.5 1.7 2.0 1.5 1.3 3.0 2.5 1.3 1.4 1.4 1.5 1.2 1.5 1.1 1.1 1.5 1.15 1.15 1.25 1.5 1.5 1.35 1.15 1.15
IF (A) 0.5 0.5 0.5 0.6 0.8 0.8 1.0 1.0 1.0 3.5 2.5 5.0 0.25 0.25 0.25 0.5 0.6 0.6 0.8 0.8 1.0 1.0 1.1 1.5 1.5 3.0 3.5 2.5 5.0 0.25 0.5 0.6 0.6 0.6 0.8 0.8 0.8 1.0 1.0 1.0 1.1 1.5 1.5 1.5 3.0 3.0 3 5.0 2.5 5.0 10 10 10
Tj (C)
trrq (s)
IF/IRP (mA)
trrw (s)
IF/IRP (mA) 10/20 10/20 10/20 10/20 10/20 10/20 10/20 10/20 10/20 10/20
Rth(j-l) Rth(j-c) (C/W) 20 17 22 15 17 22 20 17 15 8.0 4.0 4.0 20 17 15 22 22 17 20 22 20 17 15 12 12 8.0 8.0 4.0 4.0 15 22 15 22 15 20 15 22 20 17 15 15 12 15 12 8 12 4.0 4.0 4.0 4.0 4.0 4.0 4.0
Mass (g) 0.2 0.3 0.13 0.4 0.3 0.13 0.2 0.3 0.4 1.2 2.1 2.1 0.2 0.3 0.4 0.13 0.13 0.3 0.2 0.13 0.2 0.3 0.4 0.6 0.6 1.2 1.2 2.1 2.1 0.4 0.13 0.4 0.13 0.4 0.2 0.4 0.13 0.2 0.3 0.4 0.4 0.6 0.4 0.6 1.2 0.6 2.1 2.1 2.1 2.1 2.1 2.1 2.1
0.5 0.5 0.5 0.6 0.7 0.8 200 1.0 1.0 1.0 3.5
Axial(2.7/0.6) Axial(2.7/0.78) Axial(2.4/0.6) Axial(4.0/0.78) Axial(2.7/0.78) Axial(2.4/0.6) Axial(2.7/0.6) Axial(2.7/0.78) Axial(4.0/0.78) Axial(6.5/1.4)
-40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150
150 100(Ta) 150 100(Ta) 150 100(Ta) 70 150(Ta) 200 100(Ta) 250 300 3000 100 100 150
0.4 0.4 0.4 4.0 1.5 0.4 0.4 0.4 0.4 0.4
10/10 0.18 10/10 0.18 10/10 0.18 10/10 10/10 1.3 0.6
10/10 0.18 10/10 0.18 10/10 0.18 10/10 0.18 10/10 0.18
5.0 TO-220F(Center-tap) FMU-12S, R 10 TO-220F(Center-tap) FMU-22S, R 0.25 0.25 0.25 0.5 0.6 0.6 0.7 0.8 400 1.0 1.0 1.1 1.5 1.5 1.5(3.0) 2.0(3.5) Axial(2.7/0.6) Axial(2.7/0.78) Axial(4.0/0.78) Axial(2.4/0.6) Axial(2.4/0.6) Axial(2.7/0.78) Axial(2.7/0.78) Axial(2.4/0.6) Axial(2.7/0.6) Axial(2.7/0.78) Axial(4.0/0.78) Axial(4.0/0.98) Axial(4.0/0.98) Axial(6.5/1.4) Axial(6.5/1.4) EU01 EU 1 RU 1 AU01 AS01 EH 1 ES 1 AU02 EU02 EU 2 RU 2M RU 3 RU 3M RU 4 RU 4M
0.4 100/100 0.18 100/200 0.4 100/100 0.18 100/200 0.4 0.4 0.4 0.4 1.5 4.0 1.5 0.4 0.4 0.4 0.4 0.4 0.4 0.4 10/10 0.18 10/10 0.18 10/10 0.18 10/10 0.18 10/10 10/10 10/10 0.6 1.3 0.6 10/20 10/20 10/20 10/20 10/20 10/20 10/20 10/20 10/20 10/20 10/20 10/20 10/20 10/20
200 100(Ta) 200 100(Ta) 250 300 300 300 400 350 100 100 100 100 100 100
10/10 0.18 10/10 0.18 10/10 0.18 10/10 0.18 10/10 0.18 10/10 0.18 10/10 0.18
0.4 100/100 0.18 100/200 0.4 100/100 0.18 100/200 0.4 100/100 0.18 100/200 0.4 0.4 0.4 1.5 4.0 1.5 1.5 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 10/10 0.18 10/10 0.18 10/10 0.18 10/10 10/10 10/10 10/10 0.6 1.3 0.6 0.6 10/20 10/20 10/20 10/20 10/20 10/20 10/20 10/20 10/20 10/20 10/20 10/20 10/20 10/20 10/20 10/20 100/200 100/200 100/200 100/200 100/200 100/200 100/200 100/200
5.0 TO-220F(Center-tap) FMU-14S, R 10 TO-220F(Center-tap) FMU-24S, R 0.25 0.5 0.6 0.6 0.6 0.7 0.7 0.8 1.0 1.0 1.0 1.1 600 1.5 1.5 1.5 1.5(3.0) 3.0 3.0 5.0 5.0 10 10 10 20 Axial(4.0/0.78) Axial(2.4/0.6) Axial(4.0/0.78) Axial(2.4/0.6) Axial(4.0/0.78) Axial(2.7/0.6) Axial(4.0/0.78) Axial(2.4/0.6) Axial(2.7/0.6) Axial(2.7/0.78) Axial(4.0/0.78) Axial(4.0/0.78) Axial(4.0/0.98) Axial(4.0/0.78) Axial(4.0/0.98) Axial(6.5/1.4) Axial(4.0/0.98) TO-220F2Pin TO-220F2Pin TO-220F(Center-tap) TO-220F(Center-tap) TO-220F2Pin TO-220F2Pin TO-220F(Center-tap) RU 1A AU01A RF 1A AS01A RH 1A ES01A RS 1A AU02A EU02A EU 2A RU 2 RU 2AM RU 3A RU 20A RU 3AM RU 4A RY2A FMY-1036S FMU-G16S FMU-16S, R FMU-26S, R FMU-G26S FMY-1106S FMY-2206S*
10/10 0.18 10/10 0.18 10/10 0.18 10/10 0.18 10/10 0.18 10/10 0.18 10/10 0.18 10/10 0.18 10/10 0.18 0.1 0.1
300 100(Ta) 300 100(Ta) 300 400 350 350 100 100 100 100
500 100(Ta) 500 100(Ta) 3000 500 3000 3000 150 150 150 150
0.4 100/100 0.18 0.4 100/100 0.18 0.4 100/100 0.18 0.4 100/100 0.18 0.2 100/100 0.2 100/100 0.1 0.1
*Under development
204
Diodes
Values in parentheses are for the products with heatsinks (Body Diameter/Lead Diameter)
0.25 0.6 0.6 800 0.7 1.0 1.1 1.5(3.0) 0.2 0.6 1000 0.8 1.5 1.5(2.5) 1.0 1300 1.5 1.5(2.5) 0.5 0.5 0.8 1.5(2.5) 2.5 1500 5.0 10 10 10 10 10 2000 0.2
Axial(4.0/0.78) Axial(4.0/0.78) Axial(4.0/0.78) Axial(4.0/0.78) Axial(4.0/0.78) Axial(4.0/0.98) Axial(6.5/1.4) Axial(4.0/0.78) Axial(4.0/0.78) Axial(4.0/0.78) Axial(4.0/0.98) Axial(6.5/1.4) Axial(4.0/0.98) Axial(6.5/1.4) Axial(6.5/1.4) Axial(2.7/0.6) Axial(2.7/0.78) Axial(4.0/0.98) Axial(6.5/1.4) Axial(6.5/1.4) TO-220F2Pin TO-220F2Pin TO-220F2Pin TO-220F2Pin TO-220F2Pin TO-3PF2Pin Axial(4.0/0.78)
-40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150
0.4 0.4 4.0 1.5 0.4 0.4 0.4 0.4 4.0 0.4 0.4
10/10 0.18 10/10 0.18 10/10 0.18 10/10 0.18 10/10 1.3
0.4 500/500 0.18 500/1000 0.4 500/500 0.18 500/1000 1.5 1.5 4.2 10/10 10/10 10/10 0.6 0.6 1.4 0.4 1.3 10/20 10/20 100/200 100/200 100/200
200 100(Ta) 200 100(Ta) 500 100(Ta) 500 350 500 500 10000 500 500 100 100 150 150 150 150 150
0.5 500/500 0.25 500/1000 2.0 500/500 4.0 10/10 0.8 500/1000 1.3 10/20
Diodes
205
Package Surface-Mount (SJP) Surface-Mount (SJP) Surface-Mount (SJP) Surface-Mount (SJP) Surface-Mount (D pack)
Part Number SJPL-D2 SJPX-F2 SJPL-H2 SJPL-L2 SPX-G32S SPX-62S SJPX-H3 SJPL-F4 SJPL-L4 SJPD-D5* SJPD-L5 SJPL-H6 SJPX-H6
Tstg (C)
VF (V) max 0.98 0.98 0.98 0.98 0.98 0.98 0.98 1.3 1.3 1.3 1.4 1.4 1.5 1.5 1.75
IF (A)
200
-40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150
IR(H) IR trrq (mA) (ns) (A) Tj VR=VRM VR=VRM (C) max max 1.0 25 1.0 150 50 1.5 10 2.0 150 30 2.0 50 0.2 150 50 3.0 50 0.3 150 50 50 10 100(Ta) 3.0 30 3.0 5.0 2.0 1.5 3.0 50 100 50 10 50 10 15 50 10 50 10 0.2 3.0 0.05 0.1 0.1 0.15 0.1 3.0 0.1 150 150(Ta) 150 150(Ta) 150 150 150 150 150 150
trrw (ns)
IF/IRP (mA)
Mass (g) 0.072 0.072 0.072 0.072 0.41 0.41 1.4 0.072 0.072 0.072 0.072 0.072 0.072 0.072 1.4
35 100/200 25 100/200 35 100/200 35 100/200 25 100/200 25 100/200 30 100/200 25 100/200 35 100/200 35 100/200 30 100/200 35 100/200 35 100/200 20 100/200
6.0 Surface-Mount (D pack)Center-tap 10 Surface-Mount (TO220S) MPL-102S 300 400 500 2.0 1.5 3.0 1.0 3.0 2.0 2.0 3.0 Surface-Mount (SJP) Surface-Mount(SJP) Surface-Mount(SJP) Surface-Mount(SJP) Surface-Mount(SJP)
30 100/100 40 100/100 30 100/100 50 100/100 50 100/100 40 100/100 50 100/100 50 100/100 30 100/100 50 100/100
600
*Under development
Thru-Hole
VRM (V) IF (AV) (A)
Values in parentheses are for the products with heatsinks
Package Axial (Body Diameter/Lead Diameter) Axial 2.4/ 0.6 Axial 2.7/ 0.6 Axial 2.7/ 0.6
IFSM Tj (A) (C) 50Hz Single Half Sine Wave 25 50 25 25 60 30 30 30 70 80 120 35 35 65 65 100 100 65 65 150 150 100 110 100 150 150 100 40 70 75 65 75 100 100 100 100
Tstg (C)
VF (V) max 0.98 0.92 0.98 0.98 0.92 0.98 0.98 0.98 0.92 0.95 0.92 0.98 0.98 0.98 0.98 0.92 1.2 0.98 0.98 0.98 0.98 0.98 0.98 1.2 0.98 0.98 1.2 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3
IF (A) 1.0 1.5 1.5 1.5 1.5 2.0 2.0 2.0 2.0 3.5 3.5 2.5 2.5 5.0 5.0 5.0 5.0 5.0 5.0 10 10 7.5 10 10 10 10 10 2.5 5.0 5.0 5.0 7.5 10 10 10 10
IR IR(H) (A) (mA) VR=VRM VR=VRM max max 50 10 50 50 20 50 50 50 50 150 50 50 50 100 100 100 100 100 100 200 200 150 200 100 10 200 100 50 100 100 50 75 100 100 100 100 0.1 2.0 0.1 0.1 3.0 3.0 0.1 4.0 0.5 6.0 0.1 10 0.2 20 20 0.2 0.4 30 0.4 30 0.4 50 30
Tj (C) 100 150 100 100 150 150 150 150 150 150 150 150 150 150
trrq (ns)
IF/IRP (mA)
trrw (ns)
IF/IRP (mA)
Rth(j-l) (C/W) 22 20 17 20 15 15 15 12 12 8.0 8.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 2.0 2.0 2.0 4.0 4.0 4.0 4.0 4.0 4.0 2.0 4.0 2.0
Mass (g) 0.13 0.2 0.3 0.2 0.4 0.4 0.4 0.6 0.6 1.2 1.2 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 6.5 6.5 6.5 2.1 2.1 2.1 2.1 2.1 2.1 6.5 2.1 6.5
1.0 1.5 1.5 1.5 1.5 2.0 2.0 2.0 2.0 3.5 3.5
40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150
50 100/100 100 100/100 50 100/100 40 100/100 100 100/100 30 100/100 50 100/100 50 100/100 100 100/100 50 100/100 100 100/100 40 100/100 30 100/100 40 100/100 30 100/100 100 100/100 25 500/500 40 100/100 30 100/100 40 500/500 30 500/500 30 500/500 50 100/100 25 500/500 40 500/500 30 500/500 25 500/500 50 100/100 50 100/100 50 100/100 30 100/100 25 500/500 30 500/500 30 500/500 25 500/500 25 500/500
35 100/200 50 100/200 35 100/200 30 100/200 50 100/200 25 100/200 35 100/200 35 100/200 50 100/200 35 100/200 50 100/200 30 100/200 25 100/200 30 100/200 25 100/200 50 100/200
0.1 100(Ta)
4.0/ 0.98 RL 2Z Axial 4.0/ 0.98 RN 2Z Axial 6.5/ 1.4 Axial 6.5/ 1.4 Axial
RL 4Z RN 4Z
5.0 TO-220F Center-tap FML-12S 5.0 TO-220F Center-tap FMX-12S 200 5.0 5.0 5.0 TO-220F2Pin TO-220F2Pin TO-220F2Pin FML-G12S FMX-G12S FMN-G12S
10 150(Ta) 150 150 150 150 150 150 150 150 150
10 TO-220F Center-tap FMXA-2102ST 10 TO-220F Center-tap FML-22S 10 TO-220F Center-tap FMX-22S 10 10 TO-220F2Pin TO-220F2Pin FML-G22S FMX-G22S
20 100(Ta) 50 100(Ta)
15 TO-220F Center-tap FMX-22SL 20 TO-220F Center-tap FM2-2202 20 20 20 20 TO-220F Center-tap FMXA-2202S TO-3PF Center-tap FML-4202S TO-3PF Center-tap FMX-4202S TO-3PF Center-tap FMXA-4202S*
30 500/1000 25 500/1000
5.0 TO-220F Center-tap FML-13S 5.0 TO-220F2Pin FML-G13S 10 TO-220F Center-tap FML-23S 10 TO-220F Center-tap FMX-23S 300 15 TO-220F Center-tap FMXA-2153S 20 TO-220F Center-tap FMX-2203 20 20 TO-3PF Center-tap FMX-4203S TO-3PF Center-tap FMXA-4203S Center-tap FMXA-2203S 20 TO-220F
0.25 100(Ta) 0.2 100(Ta) 0.2 15 23 30 30 30 150 150 150 150 150 150
30 150(Ta)
*Under development
206
Diodes
VRM (V)
IF (AV) (A)
Values in parentheses are for the products with heatsinks
Tj (C)
Tstg (C)
VF (V) max 1.8 2.0 1.8 1.4 1.8 1.8 1.3 1.3 1.5 2.0 1.3 1.3 1.3 1.0 2.0 1.3 1.50 1.3 1.5 1.4 1.4 2.0 1.8 2.0 2.0 2.0 1.55 2.0 1.5 1.3 2.5 1.5 1.5 1.2 1.3 1.7 2.2 1.75 1.5 1.5 1.7 1.98 1.3 1.3 1.7 1.75 1.3 1.75 1.7 1.5 1.98 1.5
IF (A) 0.7 0.7 0.8 1.0 1.5 1.5 1.5 2.0 5.0 2.5 2.5 5.0 5.0 5.0 5.0 5.0 10 10 10 10 1.0 0.5 0.5 0.6 1.0 1.0 1.2 3.0 3.0 3.0 4.0 5.0 5.0 5.0 5.0 5.0 3.0 8.0 5.0 10 10 10 10 10 10 10 10 10 10 10 10 10
IR IR(H) (mA) (A) VR=VRM VR=VRM max max 100 50 50 10 500 500 10 10 50 500 50 50 100 50 500 100 100 50 100 20 10 100 100 100 500 500 50 500 50 50 500 50 100 50 50 10 500 30 50 100 100 100 100 100 20 100 100 100 100 100 100 100 0.3 0.3 0.05 2.5 2.5 0.05 0.1 15 1.5 15 0.2 10 2.5 30 0.4 30 0.2 0.1 0.5 0.5 1.0 1.0 0.1 3.0 0.1 5.0 15 0.5 10 5.0 0.1 3.0 6.0 15
Tj (C)
trrq (ns)
IF/IRP (mA)
trrw (ns)
IF/IRP (mA)
Rth(j-l) (C/W) 22 20 17 22 15 12 17 12 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 2.0 2.0 2.0 15 20 22 17 15 12 12 4.0 8.0 8.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 2.0 2.0 2.0 2.0
Mass (g) 0.13 0.2 0.3 0.13 0.4 0.6 0.3 0.6 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 6.5 6.5 6.5 0.4 0.2 0.13 0.3 0.4 0.6 0.6 2.1 1.2 1.2 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 6.5 6.5 6.5 6.5
0.7 0.7 0.8 1.0 1.2 1.2 1.5 2.0 5.0 400
15 15 15 20 50 50 40 40 50 35 40 70 70 70 65 70 100 100 100 100 20 10 15 10 50 50 30 50 80 50 50 50 50 50 60 90 50 100 50 100 100 100 100 150 180 100 150 100 100 100 100 150
40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150
0.5 100(Ta) 100 100 150 150 150 150 150 150 100 150 150 150 150 150 150 150 150 150 100 100 150 150 150 150 150 150 150 150 150 150 150 150 150 150
100 100/100 100 100/100 100 100/100 50 100/100 100 100/100 100 100/100 50 100/100 50 100/100 20 500/500 100 100/100 50 100/100 30 100/100 50 100/100 100 100/100 100 100/100 50 100/100 25 500/500 50 500/500 25 500/500 50 500/500 40 100/100 100 100/100 100 100/100 100 100/100 100 100/100 100 100/100 50 100/100 70 500/500 50 500/500 100 100/100 100 100/100 30 100/100 50 500/500 100 100/100 100 100/100 50 500/500 100 100/100 27 500/500 30 100/100 30 100/100 50 500/500 28 500/500 100 100/100 100 100/100 50 500/500 27 500/500 100 100/100 27 500/500 50 500/500 30 500/500 28 500/500 100 100/100
50 100/200 50 100/200 50 100/200 35 100/200 50 100/200 50 100/200 35 100/200 35 100/200 50 100/200 35 100/200 25 100/200 35 100/200 50 100/200 50 100/200 35 100/200
4.0/ 0.78 RG 10 Axial 4.0/ 0.98 RG 2 Axial 2.7/ 0.78 EL 1 Axial 4.0/ 0.98 RL 2 Axial
TO-220F2Pin FMXA-1054S
5.0 TO-220F Center-tap FMG-14S, R 5.0 TO-220F Center-tap FML-14S 5.0 5.0 5.0 TO-220F2Pin TO-220F2Pin TO-220F2Pin FMX-G14S FML-G14S FMN-G14S
0.1 100(Ta)
8.0 TO-220F Center-tap FMG-24S, R 10 TO-220F Center-tap FML-24S 10 20 20 20 500 1.0 0.5 0.5 0.6 1.0 1.0 1.2 3.0 3.0 3.0 4.0 5.0 5.0 5.0 5.0 5.0 600 8.0 10 10 10 10 10 10 10 10 20 20 20 20 20 20 TO-220F2Pin FMXA-1104S
0.2 100(Ta)
35 500/1000
30 500/1000 30 100/200 50 100/200 50 100/200 50 100/200 50 100/200 50 100/200 35 100/200 35 500/1000 35 500/1000 50 100/200 50 100/200 25 100/200 35 500/1000 50 100/200 50 100/200 35 500/1000 50 100/200
4.0/ 0.78 RD1105* Axial 2.7/ 0.6 Axial 2.4/ 0.6 Axial
EG01A AG01A
0.5 100(Ta)
2.7/ 0.78 EG 1A Axial 4.0/ 0.78 RG 10A Axial 4.0/ 0.98 RG 2A Axial 4.0/ 0.98 RD 2A Axial
TO-220F Two elements FMC-26U Axial 6.5/ 1.4 Axial 6.5/ 1.4 TO-220F2Pin TO-220F2Pin TO-220F2Pin TO-220F2Pin TO-220F2Pin TO-220F2Pin TO-220F2Pin TO-220F2Pin TO-220F2Pin TO-220F2Pin TO-220F2Pin TO-220F2Pin TO-220F2Pin TO-220F2Pin TO-220F2Pin RL 4A RN4A FMG-G26S FMX-G16S FML-G16S FMN-G16S FMN-1056S FMD-1056S* FMXK-1086S FMX-1106S FMX-G26S FMD-G26S FMXA-1106S FMNS-1106S FMN-1106S FMD-1106S* FMXK-1106S
3.0 100(Ta)
20 150(Ta) 0.3 100(Ta) 30 10 10 0.2 10 10 10 0.3 20 30 20 150 150 150 150 150 150 150 150 150 150 150
TO-220F Center-tap FMN-2206S TO-220F Center-tap FMXK-2206S TO-3PF Center-tap FMD-4206S TO-3PF Center-tap FMX-4206S* TO-3PF Center-tap FMXA-4206S* TO-3PF Center-tap FMN-4206S
50 100/200
*Under development
Diodes
207
VRM (V)
Tj (C)
Tstg (C)
VF (V) max 2.0 3.0 3.0 3.0 4.0 4.0 4.0 3.3 3.3 3.0 4.0 4.0 6.0 7.0
IF (A) 0.5 3.0 3.0 5.0 0.2 0.2 0.4 0.5 0.7 2.0 3.0 3.0 3.0 0.1
IR IR(H) (mA) (A) VR=VRM VR=VRM max max 10 100 100 200 100 5 5.0 50 20 500 50 500 100 2.0 0.2 0.5 1.0 2.0 0.5 0.5 0.25 2.5 0.3 3 0.5 0.01
Tj (C) 150 150 150 150 100 150 150 100 100 150 150 100
trrq (ns)
IF/IRP (mA)
trrw (ns)
IF/IRP (mA)
Mass (g) 0.13 2.1 2.1 2.1 0.13 0.2 0.4 0.2 0.4 1.2 2.1 2.1 2.1 0.4
0.5 800 3.0 5.0 0.2 0.2 0.4 1000 0.5 0.7 2.0 3.0 1200 1600 2000
40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150 40 to +150
200 100/100 70 500/500 70 500/500 70 500/500 200 100/100 200 100/100 100 100/100 100 100/100 100 100/100 100 500/500 100 500/500 70 500/500 70 500/500 100 10/20
80 100/200 35 500/1000 35 500/1000 35 500/1000 80 100/200 80 100/200 50 100/200 50 100/200 50 100/200 50 500/1000 50 500/1000 35 500/1000 35 500/1000 50 10/20
3.0 TO-220F2Pin Two elements FMC-26UA 3.0 TO-220F2Pin Two elements FMC-28UA 0.1
RP 1H
208
Diodes
-40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150
6.0 Surface-Mount (D pack)Center-tap SPB-64S 1.0 1.5 60 2.0 3.0 5.0 90 100 1.0 2.0 Surface-Mount (SJP) Surface-Mount (SJP) Surface-Mount (SJP) Surface-Mount (SJP) Surface-Mount (D pack) Surface-Mount (SJP) Surface-Mount (SJP) SJPB-D6 SJPW-F6 SJPB-H6 SJPB-L6 SPB-G56S SJPB-D9 SJPB-H9
Thru-Hole
VRM (V) IF (AV) (A) 1.0 1.0 1.5 1.7 2.5 3.0 3.0 4.0 5.0 40 5.0 6.0 10 10 10 15 15 20 20 30 Package Axial (Body Diameter/Lead Diameter) Axial( 2.4/ 0.6) Axial( 2.7/ 0.6) Axial( 2.7/ 0.78) Axial( 4.0/ 0.78) Axial( 4.0/ 0.98) TO-220F2Pin Axial( 6.5/ 1.4) TO-220F(Center-tap) Axial( 6.5/ 1.4) TO-220F2Pin TO-220F(Center-tap) TO-220F(Center-tap) TO-220F(Center-tap) TO-220F2Pin TO-220F(Center-tap) TO-220F(Center-tap) TO-220F(Center-tap) TO-220F(Center-tap) TO-220F(Center-tap) Part Number AK 04 EK 04 EK 14 RK 14 RK 34 FMB-G14 RK 44 FMB-24 RW 54 FMB-G14L FMB-24M FMB-24L FMW-24L FMB-G24H FMB-24H FMW-24H FMB-2204 FMW-2204 FMB-2304 IFSM (A) 50Hz Single Half Sine Wave 25 40 40 60 50 60 80 50 120 60 60 60 100 150 100 120 150 120 150 Tj (C) Tstg (C) VF (V) max 0.55 0.55 0.55 0.55 0.55 0.60 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.55 IF (A) 1.0 1.0 1.5 2.0 2.5 3.0 3.0 2.0 5.0 5.0 3.0 5.0 5.0 10 7.5 7.5 10 10 15 IR (mA) VR=VRM max 5.0 5.0 5.0 5.0 5.0 2.0 5.0 5.0 1.0 5.0 5.0 5.0 0.5 10 7.5 7.5 10 1.0 15 IR(H) (mA) VR=VRM max 35 35 50 70 Tj (C) 150 150 150 150 Rth(j-l) Rth(j-c) (C/W) 22 20 17 15 12 4.0 8.0 4.0 8.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 Mass (g) 0.13 0.3 0.3 0.45 0.6 2.1 1.2 2.1 1.2 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1
-40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150
175 150(Ta) 100 150(Ta) 175 175 350 250 150 150 150 150
Diodes
209
VRM (V)
Package Axial (Body Diameter/Lead Diameter) Axial( 2.4/ 0.6) Axial( 2.7/ 0.6) Axial( 2.7/ 0.78) Axial( 4.0/ 0.78) Axial( 4.0/ 0.98) Axial( 6.5/ 1.4) TO-220F(Center-tap) TO-220F2Pin TO-220F(Center-tap) TO-220F(Center-tap) TO-220F(Center-tap) TO-220F(Center-tap) TO-3PF(Center-tap) Axial( 2.4/ 0.6) Axial( 2.7/ 0.6) Axial( 2.7/ 0.78) Axial( 4.0/ 0.78) Axial( 4.0/ 0.98) Axial( 6.5/ 1.4) TO-220F(Center-tap) TO-220F2Pin TO-220F(Center-tap)
Part Number AK 06 EK 06 EK 16 RK 16 RK 36 RK 46 FMB-26 FMB-G16L FMW-2106 FMW-2156 FMW-2206 FMB-2306 FMW-4306 AK 09 EK 09 EK 19 RK 19 RK 39 RK 49 FMB-29 FMB-G19L FMB-29L
IFSM (A) 50Hz Single Half Sine Wave 10 10 25 25 40 70 40 50 100 100 120 150 150 10 10 40 40 50 60 50 60 60
Tj (C)
Tstg (C)
VF (V) max 0.62 0.62 0.62 0.62 0.62 0.62 0.62 0.72 0.70 0.70 0.70 0.70 0.70 0.81 0.81 0.81 0.81 0.81 0.81 0.81 0.81 0.81
IF (A) 0.7 0.7 1.5 1.5 2.0 3.5 2.0 6.0 5.0 7.5 10 15 15 0.7 0.7 1.5 1.5 2.0 3.5 2.0 4.0 4.0
IR (mA) VR=VRM max 1.0 1.0 1.0 1.0 2.0 3.0 2.0 5.0 3.0 5.0 1.0 8.0 3.0 1.0 1.0 2.0 2.0 3.0 5.0 3.0 5.0 5.0
Rth(j-l) Rth(j-c) (C/W) 22 20 17 15 12 8.0 4.0 4.0 4.0 4.0 4.0 4.0 2.0 22 20 17 15 12 8.0 4.0 4.0 4.0
Mass (g) 0.13 0.3 0.3 0.45 0.6 1.2 2.1 2.1 2.1 2.1 2.1 2.1 6.5 0.13 0.3 0.3 0.45 0.6 1.2 2.1 2.1 2.1
-40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150
70 150(Ta) 125 70 200 125 175 250 400 350 30 30 55 55 150 150 150 150 150 150 150 150 150 150 150 150
60
90
125 150(Ta)
Low VF A Series
Surface-Mount
VRM (V) IF (AV) (A) 1.0 30 2.0 3.0 Package Surface-Mount (SJP) Surface-Mount (SJP) Surface-Mount (SJP) Part Number SJPA-D3 SJPA-H3* SJPA-L3 IFSM (A) 50Hz Single Half Sine Wave 30 40 70 Tj (C) Tstg (C) VF (V) max 0.36 0.36 0.36 IF (A) 1.0 2.0 3.0 IR (mA) VR=VRM max 1.5 3.0 4.5 IR(H) (mA) VR=VRM max 70 140 210 Tj (C) 100(Ta) 100(Ta) 100 Rth(j-l) Rth(j-c) (C/W) 20 20 20 Mass (g) 0.072 0.072 0.072
Thru-Hole
VRM (V) 30 IF (AV) (A) 2.0 Package Axial (Body Diameter/Lead Diameter) Axial(4.0/0.78) Part Number RA 13 IFSM (A) 50Hz Single Half Sine Wave 50 Tj (C) Tstg (C) VF (V) max 0.36 IF (A) 2.0 IR (mA) VR=VRM max 3.0 IR(H) (mA) VR=VRM max 140 Tj (C) 100
*Under development
-40 to +125
210
Diodes
Low IR E Series
Surface-Mount
VRM (V) 30 40 IF (AV) (A) 2.0 2.0 Package Axial (Body Diameter/Lead Diameter) Surface-Mount (SJP) Surface-Mount (SJP) Part Number SJPE-H3* SJPE-H4 IFSM (A) 50Hz Single Half Sine Wave 40 40 Tj (C) Tstg (C) VF (V) max 0.55 0.6 IF (A) 2.0 2.0 IR (mA) VR=VRM max 0.2 0.05 IR(H) (mA) VR=VRM max 70 20 Tj (C) 150(Ta) 150 Rth(j-l) Rth(j-c) (C/W) 20 20 Mass (g) 0.072 0.072
*Under development
Thru-Hole
VRM (V) 40 60 IF (AV) (A) 15 10 10 15 20 100 20 30 30 30 10 20 150 20 30 Package TO-220F(Center-tap) TO-220F(Center-tap) TO-220F(Center-tap) TO-220F(Center-tap) TO-220F(Center-tap) TO-3PF(Center-tap) TO-220F(Center-tap) TO-262 TO-3PF(Center-tap) TO-220F(Center-tap) TO-220F(Center-tap) TO-3PF(Center-tap) TO-220F(Center-tap) Part Number FME-24H FME-2106 FMEN-210A FMEN-215A* FMEN-220A FMEN-420A FMEN-230A MPEN-230AF FMEN-430A FMEN-210B FMEN-220B FMEN-420B FMEN-230B IFSM (A) 50Hz Single Half Sine Wave 100 60 100 100 120 120 150 150 150 100 120 120 150 Tj (C) Tstg (C) VF (V) max 0.60 0.72 0.85 0.85 0.85 0.85 0.85 0.90 0.85 0.92 0.92 0.85 0.92 IF (A) 7.5 5.0 5.0 7.5 10 10 15 15 15 5.0 10 10 15 IR (mA) VR=VRM max 0.75 1.0 0.1 0.15 0.2 0.2 0.3 0.25 0.3 0.1 0.2 0.2 0.3 IR(H) (mA) VR=VRM max 50 35 50 75 100 100 150 125 150 25 50 100 75 Tj (C) 150 150 150 150 150 150 150 150 150 150 150 150 150(Ta) Rth(j-l) Rth(j-c) (C/W) 4.0 4.0 4.0 4.0 4.0 2.0 4.0 1.5 2.0 4.0 4.0 2.0 4.0 Mass (g) 2.1 2.1 2.1 2.1 2.1 6.5 2.1 1.55 6.5 2.1 2.1 6.5 2.1
-40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150 -40 to +150
*Under development
*Under development
Thru-Hole
VRM (V) IF (AV) (A) 3.0 30 10 30 Package Axial (Body Diameter/Lead Diameter) Axial(6.5/1.4) TO-220F(Center-tap) TO-220F(Center-tap) Part Number RJ 43 FMJ-23L FMJ-2303 IFSM (A) 50Hz Single Half Sine Wave 50 100 150 Tj (C) Tstg (C) VF (V) max 0.45 0.45 0.48 IF (A) 3.0 5.0 15 IR (mA) VR=VRM max 3.0 5.0 15 IR(H) (mA) VR=VRM max 100 175 500 Tj (C) 150 150(Ta) 150 Rth(j-l) Rth(j-c) (C/W) 8.0 4.0 4.0 Mass (g) 1.2 2.1 2.1
Diodes
211
Surface-Mount(SJP) Surface-Mount(SJP) Surface-Mount(SJP) Surface-Mount(SJP) Surface-Mount(SJP) Surface-Mount(SJP) Surface-Mount(SJP) Surface-Mount(SZ-10) Surface-Mount(SZ-10) Surface-Mount(SZ-10) Surface-Mount(SZ-10)
SJPZ-K28 SJPZ-E20 SJPZ-E33 SJPZ-N18 SJPZ-N27 SJPZ-N33 SJPZ-N40 SZ-10N27 SZ-10N40 SZ-10NN27 SZ-10NN40
5mA rectangular wave -55 to +150 Fig.1 Fig.1 Fig.1 Fig.1 -55 to +150 -55 to +150 -55 to +150 -55 to +150 -55 to +150 -55 to +150 -55 to +175 -55 to +175 -55 to +175 -55 to +175
0.07 0.07 0.07 0.07 0.07 0.07 0.07 2.55 2.55 2.55 2.55
10ms
Time
212
Diodes
-40 to +100
7.5
-40 to +100
20
0.3
50
0.6
-40 to +100
20
0.3
50
0.9
-40 to +100
20
0.3
Part Number
VR-60SS
VR-61SS
SV-3SS
SV-4SS
Orange
Orange Red
White
White
Display Color
Internal Connection
Diodes
213
2.30.4
0.55 0.1
2.30.4
0.55 0.1
2.60.2
5.5 0.4
a. b.
5.0
5.5 0.4
a. b.
1.2max
c.
4.9 0 to 0.25
2.5 0.4
1.2max
c.
4.9 0 to 0.25
0.050.05
2.5 0.4
2.150.2
0.5 0.2
0.55 0.1
1 NC
3 Anode
1
0.5 0.2
0.80.1
1.15 0.1
0.8 0.1
0.80.1
1.15 0.1
0.8 0.1
+0.1
1.30.4
1.30.4
1 Anode
2(Common to heatsink)
1.50.2
1 2 3
1.5 max
Cathode(Common) Anode
(1.4)
4.50.2 1.30.1
(1.4)
(5)
4.440.2 1.30.2
10.20.3
1.30.2
(0.45)
b
1 2 3
(1.5) 8.60.3
( 1.5 Dp0.2)
10.0 0.5
+0.3
10.20.3
c 1.270.2
(1.5)
0.1 0.1
+0.2
2.00.1
A 2.540.1
(Measured at the root)
0.40.1
2.540.1
(Measured at the root)
1.20.2 2.540.5
q w e
2.540.5
3.0 0.5
+0.3
2.40.2 (R0.3)
(1.2)
0.86 0.1
+0.2
(1.4)
10.20.3
4.440.2
1.30.2
10.00.3 5.00.3 (4.6) 8.50.5 100.3 50.3 20.3
0.57 0.02
10.0 0.5
+0.3
(1.5) 8.60.3
a b c 1.270.2
Cathode band
(1.5)
13.50.3
0.1 0.1
9.60.5
15.50.5
(9.75)
100.3
+0.2
2.590.2 0.40.1
(0.4)
5.00.3
+0.3
1.10.5
2.540.5
q w e
2.540.5
(2.5)
2.70.3 7.20.5
30.5
2.00.5
1.20.2
3.0 0.5
0.86 0.1
+0.2
3.90.5
50.0 1.0
2.9 0.1
2.4 0.1
0.6
Cathode band
Cathode band
0.7
62.3 0.7
5.0 0.2
62.3 1.0
5.0 0.2
2.7 0.2
2.70.2
62.3
5.0 0.2
2.7 0.2
214
Diodes
1.4 0.1
Cathode band
Cathode band
Cathode band
62.5 0.7
7.2 0.2
50 0.1
4.0 0.2
62.5 0.7
7.2 0.2
8.0 0.2
4.0 0.2
6.5 0.2
No. 18 TO-220F2Pin
10.0
3.3
4.0 8.4
4.2 2.8
16.90.3 8.40.2
0.80.2
13.0min
2.54
2.54
2.40.2
2.54
2.54
2.40.2
S type
U type
(13.5)
3.9
1.350.15 1.350.15
13.0min
3.9
1.350.15 1.350.15
0.2
0.8
2.2
16.9
a b c
3.3 0.2
0.80.2
a b c
3.3 0.2
3.9
0.2
2.6
S type
0.45
No. 20 TO-3PF
15.60.2
No. 21 TO-3PF2Pin
0.8
0.2
15.60.3
23.00.2 9.50.2
4.0 8.4
5.5
0.8 0.2
5.50.2 3.450.2
5.50.2 3.450.2
5.5
16.9
0.8
1.6
3.0
1.6
2.6
3.9
3.3
3.3
(13.5)
1.6
0.8
0.8
0.45
5.450.1 1.5
0.65+0.2 -0.1
3.350.2
5.450.1
5.450.1
0.65+0.2 0.1
3.350.2
3.0
2.2
a b
3.30.2
a b c
3.3 0.2
Diodes
215
Category
Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor
Description
Audio and General Purpose (LAPT) Audio and General Purpose (LAPT) Audio and General Purpose (LAPT) Audio and General Purpose (LAPT) Audio and General Purpose (LAPT) Audio and General Purpose (LAPT) Audio and General Purpose (LAPT) Audio and General Purpose (LAPT) General Purpose General Purpose Audio and General Purpose (Single Emitter) Audio and General Purpose (Single Emitter) Audio and General Purpose (Single Emitter) General Purpose (Low VCE (sat)) General Purpose (Low VCE (sat)) Audio Driver and General Purpose Audio Driver and General Purpose Audio and General Purpose (Single Emitter) Audio and General Purpose (Single Emitter) Audio and General Purpose (Single Emitter) Audio and General Purpose (Single Emitter) Audio and General Purpose (Single Emitter) General Purpose Audio Driver and General Purpose Audio Driver and General Purpose Audio and General Purpose (LAPT) Audio and General Purpose (Single Emitter) Audio and General Purpose (Single Emitter) Audio and General Purpose (Single Emitter) Audio and General Purpose (Single Emitter) Audio and General Purpose (Single Emitter) Audio and General Purpose (Single Emitter) General Purpose (Darlington) General Purpose (Darlington) General Purpose (Darlington) General Purpose (Darlington) General Purpose (Darlington) General Purpose (Darlington) General Purpose (Darlington) Audio and General Purpose (Darlington) Audio and General Purpose (Darlington) Audio and General Purpose (Darlington) Audio and General Purpose (Darlington) Audio and General Purpose (Darlington) Audio and General Purpose (Darlington) Audio and General Purpose (Darlington) Audio and General Purpose (Darlington) Audio and General Purpose (LAPT) Audio and General Purpose (LAPT) Audio and General Purpose (LAPT) Audio and General Purpose (LAPT) Audio and General Purpose (LAPT) Audio and General Purpose (LAPT) Audio and General Purpose (LAPT) Audio and General Purpose (LAPT) DC-DC Converter and General Purpose General Purpose General Purpose General Purpose (High hFE, Low VCE (sat)) General Purpose (High hFE, Low VCE (sat)) Audio and General Purpose (Single Emitter) Audio and General Purpose (Single Emitter) Audio and General Purpose (Single Emitter) SMPS for 200VAC system and General Purpose
Page
156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 156 158 158 158 158 158 158 158 158 158 158 158 158 158 158 158 158 158
Part No.
2SC4024 2SC4131 2SC4138 2SC4140 2SC4153 2SC4300 2SC4301 2SC4304 2SC4381 2SC4382 2SC4388 2SC4445 2SC4466 2SC4467 2SC4468 2SC4495 2SC4511 2SC4518 2SC4518A 2SC4546 2SC4706 2SC4883 2SC4883A 2SC4886 2SC5071 2SC5099 2SC5100 2SC5101 2SC5130 2SC5287 2SC6011 2SC6011A 2SC6145 2SD1785 2SD1796 2SD2014 2SD2015 2SD2016 2SD2017 2SD2045 2SD2081 2SD2082 2SD2083 2SD2141 2SD2389 2SD2390 2SD2401 2SD2438 2SD2439 2SD2560 2SD2561 2SD2562 2SD2641 2SD2642 2SD2643 2SK2420 2SK2701A 2SK2778 2SK2779 2SK2803 2SK2848 2SK2943 2SK3003 2SK3004
Category
Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor
Description
DC-DC Converter and General Purpose DC-DC Converter and General Purpose SMPS for 100VAC system and General Purpose SMPS for 100VAC system and General Purpose DC-DC Converter and General Purpose SMPS for 200VAC system and General Purpose SMPS for 200VAC system and General Purpose SMPS for 200VAC system and General Purpose Audio Driver and General Purpose Audio Driver and General Purpose Audio and General Purpose (Single Emitter) SMPS for 200VAC system and General Purpose Audio and General Purpose (Single Emitter) Audio and General Purpose (Single Emitter) Audio and General Purpose (Single Emitter) Audio Temperature Compensation and General Purpose Audio and General Purpose (Single Emitter) SMPS for 200VAC system and General Purpose SMPS for 200VAC system and General Purpose SMPS for 100VAC system and General Purpose SMPS for 200VAC system and General Purpose Audio Driver and General Purpose Audio Driver and General Purpose Audio and General Purpose (LAPT) SMPS for 100VAC system and General Purpose Audio and General Purpose (Single Emitter) Audio and General Purpose (Single Emitter) Audio and General Purpose (Single Emitter) SMPS for 100VAC system and General Purpose SMPS for 100VAC system and General Purpose Audio and General Purpose (Single Emitter) Audio and General Purpose (Single Emitter) Audio and General Purpose (Single Emitter) General Purpose (Darlington) General Purpose (Darlington) General Purpose (Darlington) General Purpose (Darlington) General Purpose (Darlington) General Purpose (Darlington) General Purpose (Darlington) General Purpose (Darlington) General Purpose (Darlington) General Purpose (Darlington) General Purpose (Darlington) Audio and General Purpose (Darlington) Audio and General Purpose (Darlington) Audio and General Purpose (Darlington) Audio and General Purpose (Darlington) Audio and General Purpose (Darlington) Audio and General Purpose (Darlington) Audio and General Purpose (Darlington) Audio and General Purpose (Darlington) General Purpose (Darlington) General Purpose (Darlington) General Purpose (Darlington) MOS FET MOS FET MOS FET MOS FET MOS FET MOS FET MOS FET MOS FET MOS FET
Page
158 158 158 158 158 158 158 158 158 158 158 158 158 158 158 158 158 158 158 158 158 158 158 158 158 158 158 158 158 158 158 158 158 160 160 160 160 160 160 160 160 160 160 160 160 160 160 160 160 160 160 160 160 160 160 164 164 164 164 164 164 164 164 164
216
Part No.
2SK3199 2SK3710A 2SK3711 2SK3800 2SK3801 AB01B AG01 AG01A AK 04 AK 06 AK 09 AL01 AL01Z AM01 AM01A AM01Z AP01C AS01 AS01A AU01 AU01A AU01Z AU02 AU02A AU02Z EG01 EG01A EG01C EG 1 EG 1A EH 1 EK 04 EK 06 EK 09 EK 14 EK 16 EK 19 EKV550 EL02Z EL 1 EL 1Z EM01 EM01A EM01Z EM 1 EM 1A EM 1B EM 1C EM 1Y EM 1Z EM 2 EM 2A EM 2B EN 01Z EP01C ES01A ES01F ES 1 ES 1F ES 1Z EU01 EU01Z EU02 EU02A
Category
Transistor Transistor Transistor Transistor Transistor Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Transistor Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode MOS FET MOS FET MOS FET MOS FET MOS FET
Description
Page
164 164 164 164 164 208 207 207 209 210 210 207 206 203 203 203 208 204 204 204 204 204 204 204 204 207 207 208 207 207 204 209 210 210 209 210 210 164 206 207 206 203 203 203 203 203 203 203 203 203 203 203 203 206 208 204 205 204 205 204 204 204 204 204
Part No.
EU02Z EU 1 EU 1Z EU 2 EU 2A EU 2Z FGM603 FGM623S FGT312 FGT313 FGT412 FGT612 FKP202 FKP250A FKP252 FKP253 FKP280A FKP300A FKP330C FKV460S FKV550N FKV550T FKV575 FKV660S FM2-2202 FMB-2204 FMB-2304 FMB-2306 FMB-24 FMB-24H FMB-24L FMB-24M FMB-26 FMB-29 FMB-29L FMB-G14 FMB-G14L FMB-G16L FMB-G19L FMB-G24H FMC-26U FMC-26UA FMC-28U FMC-28UA FMC-G28S FMC-G28SL FMD-1056S FMD-1106S FMD-4204S FMD-4206S FMD-G26S FME-2106 FME-24H FMEN-210A FMEN-210B FMEN-215A FMEN-220A FMEN-220B FMEN-230A FMEN-230B FMEN-420A FMEN-420B FMEN-430A FMG-14R
Category
Diode Diode Diode Diode Diode Diode Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode
Description
Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) IGBT IGBT IGBT IGBT IGBT IGBT MOS FET MOS FET MOS FET MOS FET MOS FET MOS FET MOS FET MOS FET MOS FET MOS FET MOS FET MOS FET Ultrafast Recovery Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (F2pin) Schottky Barrier Diode (F2pin) Schottky Barrier Diode (F2pin) Schottky Barrier Diode (F2pin) Schottky Barrier Diode (F2pin) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (F2Pin) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Ultrafast Recovery Diode (Frame)
Page
204 204 204 204 204 204 168 168 168 168 168 168 164 164 164 164 164 164 164 164 164 164 164 164 206 209 209 210 209 209 209 209 210 210 210 209 209 210 210 209 207 208 208 208 208 208 207 207 207 207 207 211 211 211 211 211 211 211 211 211 211 211 211 207
Ultrafast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Schottky Barrier Diode (Axial) Schottky Barrier Diode (Axial) Schottky Barrier Diode (Axial) Ultrafast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Ultrafast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Fast Recovery Diode (Axial) Schottky Barrier Diode (Axial) Schottky Barrier Diode (Axial) Schottky Barrier Diode (Axial) Schottky Barrier Diode (Axial) Schottky Barrier Diode (Axial) Schottky Barrier Diode (Axial) MOS FET Ultrafast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Ultrafast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial)
217
Part No.
FMG-14S FMG-24R FMG-24S FMG-26R FMG-26S FMG-G26S FMG-G2CS FMJ-2303 FMJ-23L FML-12S FML-13S FML-14S FML-22S FML-23S FML-24S FML-4202S FML-4204S FML-G12S FML-G13S FML-G14S FML-G16S FML-G22S FMM-22R FMM-22S FMM-24R FMM-24S FMM-26R FMM-26S FMN-1056S FMN-1106S FMN-2206S FMN-4206S FMN-G12S FMN-G14S FMN-G16S FMNS-1106S FMQ-G1FS FMQ-G2FLS FMQ-G2FMS FMQ-G2FS FMU-12R FMU-12S FMU-14R FMU-14S FMU-16R FMU-16S FMU-22R FMU-22S FMU-24R FMU-24S FMU-26R FMU-26S FMU-G16S FMU-G26S FMU-G2FS FMV-G5FS FMW-2106 FMW-2156 FMW-2204 FMW-2206 FMW-24H FMW-24L FMW-4306 FMX-1106S
Category
Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode
Description
Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (F2Pin) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (F2Pin) Rectifier Diode (Frame) Rectifier Diode (Frame) Rectifier Diode (Frame) Rectifier Diode (Frame) Rectifier Diode (Frame) Rectifier Diode (Frame) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (F2Pin) Fast Recovery Diode (F2Pin) Fast Recovery Diode (F2Pin) Fast Recovery Diode (F2Pin) Fast Recovery Diode (F2Pin) Fast Recovery Diode (Frame) Fast Recovery Diode (Frame) Fast Recovery Diode (Frame) Fast Recovery Diode (Frame) Fast Recovery Diode (Frame) Fast Recovery Diode (Frame) Fast Recovery Diode (Frame) Fast Recovery Diode (Frame) Fast Recovery Diode (Frame) Fast Recovery Diode (Frame) Fast Recovery Diode (Frame) Fast Recovery Diode (Frame) Fast Recovery Diode (F2Pin) Fast Recovery Diode (F2Pin) Fast Recovery Diode (F2Pin) Fast Recovery Diode (F2Pin) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame) Schottky Barrier Diode (Frame)
Page
207 207 207 207 207 207 208 211 211 206 206 207 206 206 207 206 207 206 206 207 207 206 203 203 203 203 203 203 207 207 207 207 206 207 207 207 205 205 205 205 204 204 204 204 204 204 204 204 204 204 204 204 204 204 205 205 210 210 209 210 209 209 210 207
Part No.
FMX-12S FMX-2203 FMX-22S FMX-22SL FMX-23S FMX-4202S FMX-4203S FMX-4206S FMXA-1054S FMXA-1104S FMXA-1106S FMXA-2102ST FMXA-2153S FMXA-2202S FMXA-2203S FMXA-4202S FMXA-4203S FMXA-4204S FMXA-4206S FMX-G12S FMX-G14S FMX-G16S FMX-G22S FMX-G26S FMXK-1086S FMXK-1106S FMXK-2206S FMY-1036S FMY-1106S FMY-2206S LC5205D LC5210D LC5511D LC5513D LC5521D LC5523D LC5523F MGD623N MGD623S MPE-220A MPEN-230AF MPL-102S MPL-1036S NR885K RA 13 RC 2 RD1105 RD 2A RF 1A RF 1B RG 1C RG 2 RG 2A RG 4C RG 10 RG 10A RH 1A RH 1B RH 1C RH 1Z RH 2D RH 2F RH 4F RJ 43
Category
Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode IC IC IC IC IC IC IC Transistor Transistor Diode Diode Diode Diode IC Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode
Description
Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (Frame) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (F2Pin) Ultrafast Recovery Diode (Frame) Fast Recovery Diode (F2Pin) Fast Recovery Diode (F2Pin) Fast Recovery Diode (Frame) LED Driver IC LED Driver IC LED Driver IC LED Driver IC LED Driver IC LED Driver IC LED Driver IC IGBT IGBT Schottky Barrier Diode (Surface Mount) Schottky Barrier Diode Ultrafast Recovery Diode (Surface Mount) Ultrafast Recovery Diode (Surface Mount) DC/DC Converter IC (Surface Mount) Schottky Barrier Diode (Axial) Fast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Schottky Barrier Diode (Axial)
Page
206 206 206 206 206 206 206 207 207 207 207 206 206 206 206 206 206 207 207 206 207 207 206 207 207 207 207 204 204 204 142 142 144 144 144 144 144 168 168 209 211 206 206 52 210 205 207 207 204 205 208 207 207 208 207 207 204 205 205 204 205 205 205 211
218
Part No.
RK 14 RK 16 RK 19 RK 34 RK 36 RK 39 RK 44 RK 46 RK 49 RL 2 RL 2Z RL 4A RL 4Z RL 10Z RM 1 RM 1A RM 1B RM 1C RM 1Z RM 2 RM 2A RM 2B RM 2C RM 2Z RM 4 RM 4A RM 4AM RM 4C RM 4Y RM 4Z RM 10 RM 10A RM 10B RM 10Z RM 11A RM 11B RM 11C RN 1Z RN 2Z RN 4A RN 4Z RO 2 RO 2B RO 2C RO 2Z RP 1H RS 1A RS 1B RS 4FS RU 1 RU 1A RU 1B RU 1C RU 1P RU 2 RU 2AM RU 2B RU 2C RU 2M RU 2Z RU 20A RU 3 RU 3A RU 3AM
Category
Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode
Description
Schottky Barrier Diode (Axial) Schottky Barrier Diode (Axial) Schottky Barrier Diode (Axial) Schottky Barrier Diode (Axial) Schottky Barrier Diode (Axial) Schottky Barrier Diode (Axial) Schottky Barrier Diode (Axial) Schottky Barrier Diode (Axial) Schottky Barrier Diode (Axial) Ultrafast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Ultrafast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Rectifier Diode (Axial) Ultrafast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Ultrafast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial)
Page
209 210 210 209 210 210 209 210 210 207 206 207 206 206 203 203 203 203 203 203 203 203 203 203 203 203 203 203 203 203 203 203 203 203 203 203 203 206 206 207 206 203 203 203 203 208 204 205 205 204 204 205 205 208 204 204 205 205 204 204 204 204 204 204
Part No.
RU 3B RU 3C RU 3M RU 4 RU 4A RU 4B RU 4C RU 4D RU 4DS RU 4M RU 4Z RW54 RX 10Z RY2A SAI01 SAI02 SAI03 SCM1101M SCM1101MF SCM1103M SCM1104M SCM1104MF SCM1105MF SCM1106M SCM1106MF SCM1110MF SCM1221M SCM1221MF SCM1223M SCM1224M SCM1224MF SCM1225MF SCM1226M SCM1226MF SCM1230MF SDA05 SDC03 SDC04 SDC06 SDC07 SDH02 SI-3002KWM SI-3010KD SI-3010KF SI-3010LLSL SI-3011ZD SI-3011ZF SI-3012KD SI-3012KS SI-3012LU SI-3018LSA SI-3025KS SI-3025LSA SI-3033KD SI-3033KS SI-3033LSA SI-3033ZD SI-3050KD SI-3050LSA SI-7321M SI-7510 SI-8001FDE SI-8001FDL SI-8001FFE
Category
Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC Transistor Transistor Transistor Transistor Transistor Transistor IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC
Description
Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Fast Recovery Diode (Axial) Schottky Barrier Diode (Axial) Ultrafast Recovery Diode (Axial) Fast Recovery Diode (Axial) DC/DC Converter IC (Surface Mount) DC/DC Converter IC (Surface Mount) DC/DC Converter IC (Surface Mount) High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC Array for 3-Phase Motor Drive (Surface Mount) Array for Sink Drive (Surface Mount) Array for Sink Drive (Surface Mount) Array for Sink Drive (Surface Mount) Array for 3-Phase Motor Drive (Surface Mount) Array for Sink Drive (Surface Mount) Linear Regulator IC (2 Output, Surface Mount) Linear Regulator IC (Surface Mount) Linear Regulator IC Linear Regulator IC (Surface Mount) Linear Regulator IC (Surface Mount) Linear Regulator IC Linear Regulator IC (Surface Mount) Linear Regulator IC (Surface Mount) Linear Regulator IC (Surface Mount) Linear Regulator IC (Surface Mount) Linear Regulator IC (Surface Mount) Linear Regulator IC (Surface Mount) Linear Regulator IC (Surface Mount) Linear Regulator IC (Surface Mount) Linear Regulator IC (Surface Mount) Linear Regulator IC (Surface Mount) Linear Regulator IC (Surface Mount) Linear Regulator IC (Surface Mount) 2-phase Stepper Motor Unipolar Driver IC 5-phase Stepper Motor Driver IC DC/DC Converter IC (Surface Mount) DC/DC Converter IC (Surface Mount) DC/DC Converter IC
Page
205 205 204 204 204 205 205 205 205 204 204 209 206 204 12 12 12 134 134 134 134 134 134 134 134 134 138 138 138 138 138 138 138 138 138 170 170 170 170 170 170 84 72 80 76 78 82 72 70 66 68 70 68 72 70 68 78 72 68 106 114 28 28 44
219
Part No.
SI-8005Q SI-8008HD SI-8008HFE SI-8008TFE SI-8008TM SI-8010GL SI-8010Y SI-8015JF SI-8033JD SI-8033JF SI-8033S SI-8033SD SI-8033W SI-8050E SI-8050HFE SI-8050JD SI-8050JF SI-8050S SI-8050SD SI-8050TFE SI-8050W SI-8050Y SI-8090JD SI-8090S SI-8105QL SI-8120JD SI-8120JF SI-8120S SI-8150S SI-8205NHD SI-8401L SI-8501L SI-8511NVS SJPA-D3 SJPA-H3 SJPA-L3 SJPB-D4 SJPB-D6 SJPB-D9 SJPB-H4 SJPB-H6 SJPB-H9 SJPB-L4 SJPB-L6 SJPD-D5 SJPD-L5 SJPE-H3 SJPE-H4 SJPJ-D3 SJPJ-H3 SJPJ-L3 SJPL-D2 SJPL-F4 SJPL-H2 SJPL-H6 SJPL-L2 SJPL-L4 SJPM-H4 SJPW-F6 SJPX-F2 SJPX-H3 SJPX-H6 SJPZ-E20 SJPZ-E33
Category
IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode
Description
DC/DC Converter IC (Surface Mount) DC/DC Converter IC (Surface Mount) DC/DC Converter IC DC/DC Converter IC DC/DC Converter IC (Surface Mount) DC/DC Converter IC DC/DC Converter IC DC/DC Converter IC DC/DC Converter IC (Surface Mount) DC/DC Converter IC DC/DC Converter IC DC/DC Converter IC (Surface Mount) DC/DC Converter IC (Surface Mount) DC/DC Converter IC DC/DC Converter IC DC/DC Converter IC (Surface Mount) DC/DC Converter IC DC/DC Converter IC DC/DC Converter IC (Surface Mount) DC/DC Converter IC DC/DC Converter IC (Surface Mount) DC/DC Converter IC DC/DC Converter IC (Surface Mount) DC/DC Converter IC DC/DC Converter IC DC/DC Converter IC (Surface Mount) DC/DC Converter IC DC/DC Converter IC DC/DC Converter IC DC/DC Converter IC (Surface Mount) DC/DC Converter IC (with Coil) DC/DC Converter IC (with Coil) DC/DC Converter IC (Surface Mount) Schottky Barrier Diode (Surface Mount) Schottky Barrier Diode (Surface Mount) Schottky Barrier Diode (Surface Mount) Schottky Barrier Diode (Surface Mount) Schottky Barrier Diode (Surface Mount) Schottky Barrier Diode (Surface Mount) Schottky Barrier Diode (Surface Mount) Schottky Barrier Diode (Surface Mount) Schottky Barrier Diode (Surface Mount) Schottky Barrier Diode (Surface Mount) Schottky Barrier Diode (Surface Mount) Ultrafast Recovery Diode (Surface Mount) Ultrafast Recovery Diode (Surface Mount) Schottky Barrier Diode (Surface Mount) Schottky Barrier Diode (Surface Mount) Schottky Barrier Diode (Surface Mount) Schottky Barrier Diode (Surface Mount) Schottky Barrier Diode (Surface Mount) Ultrafast Recovery Diode (Surface Mount) Ultrafast Recovery Diode (Surface Mount) Ultrafast Recovery Diode (Surface Mount) Ultrafast Recovery Diode (Surface Mount) Ultrafast Recovery Diode (Surface Mount) Ultrafast Recovery Diode (Surface Mount) Rectifier Diode (Surface Mount) Schottky Barrier Diode (Surface Mount) Ultrafast Recovery Diode (Surface Mount) Ultrafast Recovery Diode (Surface Mount) Ultrafast Recovery Diode (Surface Mount) Power Zener Diode (Surface Mount) Power Zener Diode (Surface Mount)
Page
26 30 46 36 18 38 48 34 16 34 40 20 14 32 46 16 34 40 20 36 14 48 16 40 42 16 34 40 40 50 54 54 62 210 210 210 209 209 209 209 209 209 209 209 206 206 211 211 211 211 211 206 206 206 206 206 206 203 209 206 206 206 212 212
Part No.
SJPZ-K28 SJPZ-N18 SJPZ-N27 SJPZ-N33 SJPZ-N40 SKP202 SKP253 SLA0201 SLA2601M SLA2602M SLA4030 SLA4031 SLA4036 SLA4041 SLA4051 SLA4052 SLA4060 SLA4061 SLA4070 SLA4071 SLA4390 SLA5022 SLA5037 SLA5041 SLA5059 SLA5060 SLA5061 SLA5064 SLA5065 SLA5068 SLA5073 SLA5074 SLA5075 SLA5085 SLA5086 SLA5096 SLA5201 SLA5212 SLA5222 SLA5227 SLA6012 SLA6020 SLA6022 SLA6023 SLA6024 SLA6026 SLA6805MP SLA6826M SLA6827M SLA6828M SLA6845M SLA6866M SLA6868M SLA6870M SLA7022MU SLA7024M SLA7026M SLA7027MU SLA7029M SLA7031M SLA7032M SLA7033M SLA7050M SLA7051M
Category
Diode Diode Diode Diode Diode Transistor Transistor Thyristor IC IC Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC
Description
Power Zener Diode (Surface Mount) Power Zener Diode (Surface Mount) Power Zener Diode (Surface Mount) Power Zener Diode (Surface Mount) Power Zener Diode (Surface Mount) MOS FET MOS FET Thyristor Array HID Lamp Driver IC HID Lamp Driver IC Array for Sink Drive Array for Sink Drive Array for Sink Drive Array for Sink Drive Array for Sink Drive Array for Sink Drive Array for Sink Drive Array for Sink Drive Array for Source Drive Array for Source Drive Array for H-Bridge Motor Drive Array for 3-Phase Motor Drive Array for Sink Drive Array for Sink Drive Array for 3-Phase Motor Drive Array for 3-Phase Motor Drive Array for 3-Phase Motor Drive Array for 3-Phase Motor Drive Array for 5-Phase Motor Drive Array for 5-Phase Motor Drive Array for 5-Phase Motor Drive Array for 5-Phase Motor Drive Array for 3-Phase Motor Drive Array for Sink Drive Array for Source Drive Array for 3-Phase Motor Drive Array for 3-Phase Motor Drive Array for 3-Phase Motor Drive Array for Partial switching PFC Array for Partial switching PFC Array for 3-Phase Motor Drive Array for 3-Phase Motor Drive Array for 3-Phase Motor Drive Array for 3-Phase Motor Drive Array for 3-Phase Motor Drive Array for 3-Phase Motor Drive High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC
Page
212 212 212 212 212 164 164 190 146 146 170 170 170 170 170 170 170 170 170 170 170 170 170 170 170 170 170 170 170 170 170 170 170 170 170 170 170 170 170 170 170 170 170 170 170 170 130 122 122 122 132 128 128 128 90 94 94 94 90 96 96 96 98 98
220
Part No.
SLA7052M SLA7060M SLA7061M SLA7062M SLA7065M SLA7066M SLA7067M SLA7070MPR SLA7070MR SLA7071MPR SLA7071MR SLA7072MPR SLA7072MR SLA7073MPR SLA7073MR SLA7075MPR SLA7075MR SLA7076MPR SLA7076MR SLA7077MPR SLA7077MR SLA7078MPR SLA7078MR SLA7080MPR SLA7081MPR SLA7082MPR SLA7083MPR SLA7611M SMA4020 SMA4021 SMA4030 SMA4032 SMA4033 SMA4036 SMA4038 SMA5106 SMA5112 SMA5117 SMA5118 SMA5125 SMA5127 SMA5130 SMA5131 SMA5132 SMA5133 SMA6010 SMA6080 SMA6511 SMA6821MP SMA6822MP SMA6823MP SMA6853M SMA6854M SMA6862M SMA6863M SMA6865M SMA7022MU SMA7029M SMA7036M SPB-64S SPB-G34S SPB-G54S SPB-G56S SPI-6631M
Category
IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor IC IC IC IC IC IC IC IC IC IC IC Diode Diode Diode Diode IC
Description
2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 3-phase Stepper Motor Driver IC Array for Source Drive Array for Source Drive Array for Sink Drive Array for Sink Drive Array for Sink Drive Array for Sink Drive Array for Sink Drive Array for Sink Drive Array for 3-Phase Motor Drive Array for 3-Phase Motor Drive Array for 3-Phase Motor Drive Array for 3-Phase Motor Drive Array for 3-Phase Motor Drive Array for 3-Phase Motor Drive Array for 3-Phase Motor Drive Array for 3-Phase Motor Drive Array for 3-Phase Motor Drive Array for 3-Phase Motor Drive Array for 3-Phase Motor Drive Array for Stepper Motor drive High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC 2-phase Stepper Motor Unipolar Driver IC Schottky Barrier Diode (Surface Mount) Schottky Barrier Diode (Surface Mount) Schottky Barrier Diode (Surface Mount) Schottky Barrier Diode (Surface Mount) Low Voltage 3 Phase Motor Driver IC
Page
98 108 108 108 104 104 104 100 100 100 100 100 100 100 100 110 110 110 110 110 110 110 110 102 102 102 102 112 171 171 171 171 171 171 171 171 171 171 171 171 171 171 171 171 171 171 171 171 122 122 122 124 124 126 126 126 90 90 92 209 209 209 209 118
Part No.
SPI-8001TW SPI-8002TW SPI-8003TW SPI-8010A SPX-62S SPX-G32S SSC2001S SSC2101S SSC9512 SSC9512S STA203A STA301A STA302A STA303A STA322A STA401A STA402A STA403A STA404A STA406A STA408A STA412A STA413A STA421A STA431A STA434A STA457C STA460C STA471A STA472A STA473A STA475A STA481A STA485A STA6940M STA801M STD01N STD01P STD03N STD03P STR-A6051M STR-A6052M STR-A6053M STR-A6059H STR-A6062H STR-A6069H STR-A6079M STR-A6131 STR-A6131M STR-A6132 STR-A6151 STR-A6151M STR-A6153E STR-A6159 STR-A6159M STR-A6169 STR-L451 STR-L472 STR-L6472 STR-V152 STR-V153 STR-V653 STR-W6051S STR-W6052S
Category
IC IC IC IC Diode Diode IC IC IC IC Thyristor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor IC IC Transistor Transistor Transistor Transistor IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC
Description
DC/DC Converter IC (2 Output, Surface mount) DC/DC Converter IC (2 Output, Surface mount) DC/DC Converter IC (2 Output, Surface mount) DC/DC Converter IC (Surface Mount) Ultrafast Recovery Diode (Surface Mount) Ultrafast Recovery Diode (Surface Mount) PFC IC PFC IC AC/DC Converter IC AC/DC Converter IC Triac Array Array for Sink Drive Array for 3-Phase Motor Drive and Source Drive Array for 3-Phase Motor Drive and Sink Drive Array for Source Drive Array for Sink Drive Array for Source Drive Array for Sink Drive Array for Sink Drive Array for Sink Drive Array for Source Drive Array for Sink Drive Array for Sink Drive Array for Sink Drive Array for H-Bridge Motor Drive Array for H-Bridge Motor Drive Array for H-Bridge Motor Drive Array for Sink Drive Array for Sink Drive Array for Source Drive Array for Sink Drive Array for Sink Drive Array for Sink Drive Array for Sink Drive Brush DC Motor Driver IC DC/DC Converter IC (2 Output) Audio (Darlington) Audio (Darlington) Audio (Darlington) Audio (Darlington) AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC
Page
58 58 58 22 206 206 6 6 8 8 192 171 171 171 171 171 171 171 171 171 171 171 171 171 171 171 171 171 171 171 171 171 171 171 116 56 160 160 160 160 6 6 6 6 6 6 6 7 7 7 7 7 7 7 7 7 8 8 7 7 7 6 6 6
221
Part No.
STR-W6053S STR-W6251D STR-W6252D STR-W6253D STR-W6723N STR-W6734 STR-W6735 STR-W6735N STR-W6750F STR-W6753 STR-W6754 STR-W6756 STR-W6756N STR-W6765 STR-W6765N STR-X6729 STR-X6737 STR-X6737M STR-X6750B STR-X6750F STR-X6756 STR-X6757 STR-X6757N STR-X6759B STR-X6759F STR-X6759N STR-X6768N STR-X6769 STR-X6769B STR-Y6453 STR-Y6456 STR-Y6473 STR-Y6476 STR-Y6735 STR-Y6753 STR-Y6754 STR-Y6763 STR-Y6765 STR-Y6766 SV-3SS SV-4SS SX68001M SX68002M SX68003M SZ-10N27 SZ-10N40 SZ-10NN27 SZ-10NN40 TF361H-A TF541S-A TF561S-A TFA37S TFA38S TFA57S TFA58S TFA87S TFA88S TFA107S TFA108S TFC563D TMA34S-L TMA36G-L TMA36H-L TMA36S-L
Category
IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC Diode Diode IC IC IC Diode Diode Diode Diode Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor
Description
AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC AC/DC Converter IC Silicon Varistor (Axial) Silicon Varistor (Axial) High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC High Voltage 3 Phase Motor Driver IC Power Zener Diode (Surface Mount) Power Zener Diode (Surface Mount) Power Zener Diode (Surface Mount) Power Zener Diode (Surface Mount) Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor for HID Lamp Ignition Triac Triac Triac Triac
Page
6 6 6 6 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 7 7 7 7 7 7 7 7 7 7 213 213 120 120 120 212 212 212 212 190 190 190 190 190 190 190 190 190 190 190 190 192 192 192 192
Part No.
TMA54S-L TMA56G-L TMA56H-L TMA56S-L TMA84S-L TMA86G-L TMA86H-L TMA86S-L TMA104S-L TMA106G-L TMA106H-L TMA106S-L TMA124S-L TMA126G-L TMA126H-L TMA126S-L TMA164B-L TMA164P-L TMA164S-L TMA166B-L TMA166G-L TMA166H-L TMA166P-L TMA166S-L TMA204S-L TMA206S-L TMA254B-L TMA256B-L TMB166S-L TMB206S-L VR-60SS VR-61SS
Category
Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Thyristor Diode Diode Triac Triac Triac Triac Triac Triac Triac Triac Triac Triac Triac Triac Triac Triac Triac Triac Triac Triac Triac Triac Triac Triac Triac Triac Triac Triac Triac Triac Triac Triac
Description
Page
192 192 192 192 192 192 192 192 192 192 192 192 192 192 192 192 192 192 192 192 192 192 192 192 192 192 192 192 192 192 213 213
222
NOTE
NOTE
Korea
Sanken Electric Korea Co., Ltd.
Samsung Life Yeouido Building 16F, 23-10, Yeouido-Dong, Yeongdeungpo-gu, Seoul 150-734, Korea Te l : 82-2-714-3700 Fax: 82-2-3272-2145
Singapore
Sanken Electric Singapore Pte. Ltd.
152 Beach Road, #10-06 The Gateway East, Singapore 189721 Te l : 65-6291-4755 Fax: 65-6297-1744
Malaysia
Sanken Electric (Malaysia) Sdn. Bhd.
Block B-20-5, Level 20, Northpoint Midvalley City, No.1, Medan Syed Putra Utara, 59200 Kuala Lumpur, Malaysia Te l : 60-3-2282-2345 Fax: 60-3-2282-6345
Europe
United Kingdom
Sanken Power Systems (UK) Ltd.
Pencoed Technology Park Pencoed, Bridgend CF35 5HY, United Kingdom Te l : 44-1656-869-100 Fax: 44-1656-869-162
North America
United States
Allegro MicroSystems, Inc.
115 Northeast Cutoff Worcester, Massachusetts 01606, U.S.A. Te l : 1-508-853-5000 Fax: 1-508-853-7895
This is notification that you, as purchaser of the products/technology, are not allowed to perform any of the following: 1. Resell or retransfer these products/technology to any party intending to disturb international peace and security. 2. Use these products/technology yourself for activities disturbing international peace and security. 3. Allow any other party to use these products/technology for activities disturbing international peace and security. Also, as purchaser of these products/technology, you agree to follow the procedures for the export or transfer of these products/technology, under the Foreign Exchange and Foreign Trade Law, when you export or transfer the products/technology abroad.
H1-O03EF0-1103015ND