Anda di halaman 1dari 26

COMPANY HISTORY

1960 Business Started 1962 from Grey Iron Pot 1963 1964 1965 1966 1967 1968 1969 Malleable Iron Pipe 1970 Fittings 1971 1972 1973 1974 Malleable Iron Pipeclamp 1976 Fittings 1977 1978 1979 1980 Ductile Iron Pipe 1982 Fittings 1983 1984 1985 1986 1987 1988 1989 Cast Iron Fittings Export, Main Market: Southeast Asia 1981 1975 1961

1990 Pipe Hangers and Brackets 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 Electric Power Fittings 2008 2009 2010 2011 Valve Business Development Ductile Iron Grooved Fittings Bronze Fittings, Ball Valves Steel Pipe Nipples Red Brass Pipe Nipples Self Export, Developped US and European Market

Extra-heavy 2012 Brass Pipe Nipples

Steel Pipe 2013 Development

BS VALVES

BS 5163 Resilient Wedge Gate Valve


Statement: Gate valves serve to cut the medium flow in the piping system, widely used in the field of potable water, water supply and drainage, sewage disposal, irrigation, air conditioning, fire protection as well as chemical and energy industry. Features: 1. Material: Ductile Iron EN-GJS-450-10 Body, bonnet, wedge, handwheel and operating nut are all produced in ductile iron material which provides guarantee for high strength and good corrosion resistance. 2. Triple O-ring Stem Seals The lower O-ring isolates the stem thrust collar bearing area from the waterway. The upper two O-rings can easily be replaced in the line while the valve is under pressure in the open position. 3. Stainless Steel Stem, Brass Thrust Collar and Bronze Wedge Nut This life-tested MEIDE design has repeatedly proven its superior strength and abrasive resistance. 4. Fusion Bonded Epoxy Coating Fusion bonded epoxy coating in accordance with ANSI/AWWA C550 for both interior and exterior surface which provides reliable corrosion resistance. 5. Long Service Life with Resilient Seat Cycling Test 1,000 times The Valve has been subjected to 1,000 cycles of operation at a maximum rate of 6 cycles of operation per minute from fully closed to fully open and from fully open to fully closed positions under cycled hydrostatic pressure.

BS 5163 Flanged Resilient NRS Gate Valve Type A T Key (Z45X) PN10/16, UL/FM Approved

MATERIAL SPECIFICATION Part No. 1 2 3 4 5 6 7 8 Part Valve Body Resilient Wedge Disc Stem Nut Bonnet O-Ring Gland Handwheel Bolt Flat Washer Ring Wiper Bolt Flat Washer O-Ring Thrust Washer Bonnet Gasket Wedge Nut Standard Specication EN-GJS-450-10 EN-GJS-450-10+EPDM SS420 Carbon Steel Zinc Plated EN-GJS-450-10 NBR EN-GJS-450-10 EN-GJS-450-10 Carbon Steel Zinc Plated Carbon Steel Zinc Plated NBR Carbon Steel Zinc Plated Carbon Steel Zinc Plated NBR Brass HPb59-1 EPDM Brass HPb59-1 NBR Bronze ZQSn5-5-5 Pressed Steel SS304, SS316 SS304, SS316 EPDM SS304, SS316 SS304, SS316 EPDM EPDM SS304, SS316, SS431, Al-bronze SS304, SS316 Options

Z45X
Body, Bonnet, Wedge & Operating Nut in Ductile Iron Triple O-ring Stem Seals Stainless Steel Stem and Brass Thrust Collar Bronze Alloy Wedge Nut Fusion Bonded Epoxy Coating

Connection Ends: Flange to BS EN 1092-2:1997 Working Pressure: PN10/PN16 Temperature Range: 0- 80 Coating: Fusion Bonded Epoxy Coating in accordance with ANSI/AWWA C550

9 10 11 12 13 14 15 16 17

Note: For special material request other than standard specication, please indicate clearly on the inquiry or order list.
DN Inch 2" 2.5" 3" 4" 5" 6" 8" 10" 12" mm 50 65 80 100 125 150 200 250 300 350 400 450 500 600 PN 10/16 10/16 10/16 10/16 10/16 10/16 10 16 10 16 10 16 10 16 10 16 10 16 10 16 10 16 Dimensions(mm) L 178 190 203 229 254 267 292 330 356 381 406 650 700 800 H 218 232 281 316 393 420 490 626 722 800 870 1150 1250 1350 D 165 185 200 220 250 285 340 405 460 520 580 640 715 840 D1 125 145 160 180 210 240 295 350 355 400 410 460 470 515 525 565 585 620 650 725 770 d 99 118 132 156 184 211 266 319 370 428 480 548 609 720 C 19 19 19 19 19 19 20 22 24.5 26.5 28 30 31.5 36 T 3 3 3 3 3 3 3 3 4 4 4 4 4 4 n-d 4-19 4-19 8-19 8-19 8-19 8-23 8-23 12-23 12-23 12-28 12-23 12-28 16-23 16-28 16-28 16-31 20-28 20-31 20-28 20-34 20-31 20-37

Z45X Flanged Resilient NRS Gate Valve Type A Page 11

Z45XB Flanged Resilient NRS Gate Valve Type B Page 12

Z41X Z85X Flanged Resilient OS&Y Gate Valve Grooved Resilient NRS Gate Valve Page 13 Page 14

Z45X-1

Z45XC

Z81X Grooved Resilient OS&Y Gate Valve Page 15

Z45XC-2 Flanged Resilient NRS Gate Valve with Post Flange

SMC XZA Details for electric drive available upon request.

14" 16" 18" 20" 24"

IP Vertical Indicator Post

10

11

BS VALVES

BS 5163 Flanged Resilient NRS Gate Valve Type B Ring Key and Bar (Z45XB) PN10/16, UL/FM Approved

BS 5163 Flanged Resilient OS&Y Gate Valve (Z41X) PN10/16, UL/FM Approved

MATERIAL SPECIFICATION Part No. Part Standard Specication Options 1 Valve Body EN-GJS-450-10 2 Resilient Wedge disc EN-GJS-450-10+EPDM 3 Stem SS431 SS304, SS316, Al-bronze 4 Bonnet Gasket EPDM NBR 5 Bonnet EN-GJS-450-10 6 O-Ring NBR EPDM 7 Gland EN-GJS-450-10 8 Handwheel EN-GJS-450-10 Pressed Steel 9 Bolt Carbon Steel Zinc Plated SS304, SS316 10 Flat Washer Carbon Steel Zinc Plated SS304, SS316 11 Ring Wiper EPDM NBR 12 O-Ring NBR EPDM 13 Nut Carbon Steel Zinc Plated SS304, SS316 14 Axis guide Brass Hpb59-1 15 Washer Brass Hpb59-1 16 O-Ring NBR EPDM 17 Nut Carbon Steel Zinc Plated SS304, SS316 18 Wedge nut Brass Hpb59-1 Bronze ZQSn5-5-5 Note: For special material request other than standard specication, please indicate clearly on the inquiry or order list. mm 50 65 80 100 125 150 200 250 300 350 400 450 500 600 PN 10 16 10 16 10 16 10 16 10 16 10 16 10 16 10 16 10 16 10 16 10 16 10 16 10 16 10 16 L 178 190 203 229 254 267 292 330 356 381 406 650 700 800 H 254 275 301 355 393 448 548 626 722 800 870 1150 1250 1350 D 165 185 200 220 250 285 340 405 460 520 580 640 715 840 Dimensions(mm) D1 d 125 145 160 180 210 240 295 350 355 400 410 460 470 515 525 565 585 620 650 725 770 99 118 132 156 184 211 266 319 370 428 480 548 609 720 C 19 19 19 19 19 19 20 22 24.5 26.5 28 30 31.5 36 T 3 3 3 3 3 3 3 3 4 4 4 4 4 4 n-L 4-19 4-19 8-19 8-19 8-19 8-23 8-23 12-23 12-23 12-28 12-23 12-28 16-23 16-28 16-28 16-31 20-28 20-31 20-28 20-34 20-31 20-37 Inch 2" 2.5" 3" 4" 5" 6" 8" 10" 12" 14" 16" 18"

MATERIAL SPECIFICATION Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Part Valve Body Resilient Wedge Disc O-ring Stem Nut Bonnet Stem Bushing Gland Flat Washer Stud Nut Yoke Nut Washer Locknut Handwheel Stem Packing Bonnet Gasket Standard Specication EN-GJS-450-10 EN-GJS-450-10+EPDM NBR SS420 Carbon Steel Zinc Plated EN-GJS-450-10 Brass Hpb59-1 EN-GJS-450-10 Carbon Steel Zinc Plated Carbon Steel Zinc Plated Carbon Steel Zinc Plated EN-GJS-450-10 Brass Hpb59-1 Brass Hpb59-1 Carbon Steel Zinc Plated EN-GJS-450-10 NBR EPDM Pressed Steel EPDM NBR SS304, SS316 SS304, SS316 SS304, SS316 EPDM SS304, SS16, Al-bronze SS304, SS316 Options

Z45XB

Z41X

Connection Ends: Flange to BS EN 1092-2:1997 Working Pressure: PN10/PN16 Temperature Range: 0- 80 Coating: Fusion Bonded Epoxy Coating in accordance with ANSI/AWWA C550
DN Inch 2" 2.5" 3" 4"

Connection Ends: Flange to BS EN 1092-2:1997 Working Pressure: PN10/PN16 Temperature Range: 0- 80 Coating: Fusion Bonded Epoxy Coating in accordance with ANSI/AWWA C550

Note: For special material request other than standard specication, please indicate clearly on the inquiry or order list. DN mm 50 65 80 100 125 150 200 250 300 350 400 450 PN 10 16 10 16 10 16 10 16 10 16 10 16 10 16 10 16 10 16 10 16 10 16 10 16 L 178 190 203 229 254 267 292 330 356 381 406 650 H1 (Close) 257 305 350 422 515 563 675 905 1030 1210 1280 1700 H2 (Open) 307 370 430 522 640 713 875 1155 1330 1560 1680 2150 D 165 185 200 220 250 285 340 405 460 520 580 640 Dimensions(mm) D1 125 145 160 180 210 240 295 350 355 400 410 460 470 515 525 565 585 d 99 118 132 156 184 211 266 319 370 429 480 548 C 19 19 19 19 19 19 19 22 24.5 26.5 28 30 T 3 3 3 3 3 3 3 3 4 4 4 4 n-L 4-19 4-19 8-19 8-19 8-19 8-23 8-23 12-23 12-23 12-28 12-23 12-28 16-23 16-28 16-28 16-31 20-28 20-31

Z45XB-1

Z45XBC

5" 6" 8" 10" 12" 14" 16" 18" 20" 24"

12

13

BS VALVES

BS 5163 Grooved Resilient NRS Gate Valve (Z85X), PN10/16

BS 5163 Grooved Resilient OS&Y Gate Valve (Z81X), PN10/16

MATERIAL SPECIFICATION Part No. 1 2 3 Part Valve Body Resilient Wedge Disc Stem Nut Bonnet O-Ring Gland Handwheel Bolt Flat Washer Ring Wiper Bolt Flat Washer O-Ring Washer Bonnet Gasket Wedge Nut Standard Specication EN-GJS-450-10 EN-GJS-450-10+EPDM SS420 Carbon Steel Zinc Plated EN-GJS-450-10 NBR EN-GJS-450-10 EN-GJS-450-10 Carbon Steel Zinc Plated Carbon Steel Zinc Plated NBR Carbon Steel Zinc Plated Carbon Steel Zinc Plated NBR Brass HPb59-1 EPDM Brass HPb59-1 NBR Bronze ZQSn5-5-5 Pressed Steel SS304, SS316 SS304, SS316 EPDM SS304, SS316 SS304, SS316 EMDM EPDM SS304, SS316, Al-bronze SS304, SS316 Options

MATERIAL SPECIFICATION Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Part Valve Body Resilient Wedge Disc O-Ring Stem Nut Bonnet Stem Bushing Gland Flat Washer Stud Nut Yoke Stem Nut Washer Locknut Handwheel Stem Packing Bonnet Gasket Standard Specication EN-GJS-450-10 EN-GJS-450-10+EPDM NBR SS420 Carbon Steel Zinc Plated EN-GJS-450-10 Brass Hpb59-1 EN-GJS-450-10 Carbon Steel Zinc Plated Carbon Steel Zinc Plated Carbon Steel Zinc Plated EN-GJS-450-10 Brass Hpb59-1 Brass Hpb59-1 Carbon Steel Zinc Plated EN-GJS-450-10 NBR EPDM Pressed Steel EPDM NBR Bronze ZQSn5-5-5 SS304, SS316 SS304, SS316 SS304, SS316 EPDM SS304, SS316, Al-bronze SS304, SS316 Options

Z85X

4 5 6

Z81X

Connection Ends: Groove to ISO 6182 Working Pressure: PN10/PN16 Temperature Range: 0- 80 Coating: Fusion Bonded Epoxy Coating in accordance with ANSI/AWWA C550 or painting upon request

7 8 9 10 11 12 13 14 15 16 17

Connection Ends: Groove to ISO 6182 Working Pressure: PN10/PN16 Temperature Range: 0- 80 Coating: Fusion Bonded Epoxy Coating in accordance with ANSI/AWWA C550 or painting upon request

Note: For special material request other than standard specication, please indicate clearly on the inquiry or order list. DN Inch 2" mm 50 L 178 H 218 Dimensions(mm) OD 60.3 d 57.15 A 15.88 B 7.92 DN Inch 2" mm 50

Note: For special material request other than standard specication, please indicate clearly on the inquiry or order list. Dimensions(mm) L 178 H1(Close) 257 H2(Open) 307 OD 60.3 d 57.15 A 15.88 B 7.92

2.5"

65
65 80 100 125

190
190 203 229 254

230
230 281 316 393

73
76.1 88.9 114.3 139.7

69.09
72.26 84.94 110.08 135.48

15.88
15.88 15.88 15.88 15.88

7.92
7.92 7.92 9.52 9.52

Z55X

2.5" 3" 4" 5"

2.5"
2.5" 3" 4" 5"

65
65 80 100 125

190
190 203 229 254

305
305 350 422 516

370
370 430 522 640

73
76.1 88.9 114.3 139.7

69.09
72.26 84.94 110.08 135.48

15.88
15.88 15.88 15.88 15.88

7.92
7.92 7.92 9.52 9.52

5"
6"

125
150

254
267

393
420

141.3
165.1

137.03
160.90

15.88
15.88

9.52
9.52

6"
8" 10" 12"

150
200 250 300

267
292 330 356

420
490 626 722

168.3
219.1 273.0 323.9

163.96
214.40 268.28 318.29

15.88
19.05 19.05 19.05

9.52
11.13 12.70 12.70

5"
6"

125
150

254
267

516
563

640
713

141.3
165.1

137.03
160.90

15.88
15.88

9.52
9.52

6"
8" 10" 12"

150
200 250 300

267
292 330 356

563
675 904 1030

713
875 1158 1335

168.3
219.1 273.0 323.9

163.96
214.40 268.28 318.29

15.88
19.05 19.05 19.05

9.52
11.13 12.70 12.70

14

15

BS VALVES

BS EN 593 Resilient Centerline Buttery Valve


Statement: Resilient centerline buttery valves usually serve to cut off medium ow in the piping system, widely applied in the field of potable water, water supply and drainage, sewage disposal, irrigation, air conditioning, re protection as well as chemical and energy industry. The design of the buttery valves, however, makes it also suitable to serve as adjusting valve. Features: 1. Material: Body and lever are all produced in ductile iron material (EN-GJS-450-10) which provides guarantee for high strength and good corrosion resistance. Different options of the disc and seat, e.g. disc of DI nickel or nylon 11 coated, different series of stainless steel, Al-bronze, seat in EPDM, NBR or Fluororubber, makes it suitable to be applied under different working conditions. 2. Design: Universal ange connection to BS EN 1092 PN6/10/16, ANSI B16.1 CLASS 125/150, GB9113, JIS B2112 10K, AS 2129 Table E, BS 10 Table D/E. Different options of operation including lever handle, gear box, gear box with tamper switch, electric drive, and pneumatic drive, etc. Different options of rubber seat including insert rubber seat, rubber vulcanized on valve body and boot rubber seat. 3. Coating Fusion bonded epoxy coating of valve body and lever provides reliable corrosion resistance. To achieve higher corrosion resistance, factory is also able to supply Nylon 11 coated disc. Nylon 11 coating is thermoplastic plant coating approved by USDA with high corrosion resistance and antisepsis which can be applied where there is strict requirement for anticorrosion.

BS EN 593 Wafer Buttery Valve (D71X4, D371X4, XD371X4), PN10/16

MATERIAL SPECIFICATION Part No. 1 2 3 4 Ductile Iron Lever and Body Stainless Steel Stem Fusion Bonded Epoxy Coating Disc: DI, Stainless Steel or Al-bronze Seat: EPDM/NBR/Fluororubber with backing Part Valve Body Seat Disc Stem O-Ring Bushing Lever Standard Specication EN-GJS-450-10 EPDM & Backing EN-GJS-450-10 SS420 NBR Nylon 1010 EN-GJS-450-10 NBR/Fluororubber & Backing; EPDM/NBR Vulcanized on Valve Body; Soft Seat in EPDM/NBR; SS304, SS316, AL-Bronze UNC 95400 SS304, SS316, SS416, SS431 EPDM PTFE Aluminum Options

D71X4

5 6 7

Design Standard: BS EN 593 Connection Ends: BS EN 1092 PN10/PN16, AS 2129 TABLE E, JIS B2212 10K, BS 10 TABLE D/E Top Flange Standard: ISO 5211 Stem drive by keys, parallel or diagonal square or at head Working Pressure: PN10/PN16 Temperature Range: 0- 80 Coating: Fusion Bonded Epoxy Coating in accordance with ANSI/AWWA C550

Note: For special material request other than standard specication, please indicate clearly on the inquiry or order list.

D371X4
DN Inch mm 40 50 65 80 100 125 150 200 250 300 350 400 A 138 140.5 153 157.5 176 191 202.5 243.5 273 311 340 400 B 64.5 64.5 72 86 100 112 128 162 194 223 267 300 C 33 43 46 46 52 56 56 60 68 78 78 102 D 43.9 53.9 65.2 79.7 105 130 156 206.7 253.3 301.9 333.9 389.6 D1 110 125 145 160 180 210 240 295 355 410 470 525 1.5" 2" 2.5" 3" 4" 5" 6" 8" 10" Dimensions(mm) V 32 32 32 32 32 32 32 45 45 45 45 48

XD371X4
2 12.6 14 14 14 16 16 20 26 26 28 31.6 33.2 N- 4-19 4-19 4-19 8-19 8-19 8-19 8-23 12-23 12-28 12-28 16-28 16-31 G 9.45 9.53 9.53 9.53 11.14 11.14 12.7 20.6 20.6 22.1 22.1 27 L 267 267 267 267 267 267 267 356 356 490 ISO 5211 F07 F07 F07 F07 F07 F07 F07 F10 F10 F10 F12 F14

D71X4 Wafer Buttery Valve Page 17

D71XL4 Lugged Wafer Buttery Valve Page 18

D41X4 Flanged Buttery Valve Page 19

D81X4 Grooved Buttery Valve Page 20

Details for electric drive available upon request.

12" 14" 16"

Note: Not designed for dead end service

16

17

BS VALVES

BS EN 593 Lugged Wafer Buttery Valve (D71XL4, D371XL4), PN10/16

BS EN 593 Flanged Buttery Valve (D41X4, D341X4), PN10/16

MATERIAL SPECIFICATION Part No. 1 2 Part Valve Body Seat Disc Stem O-Ring Bushing Lever Standard Specication EN-GJS-450-10 EPDM & Backing EN-GJS-450-10 SS420 NBR Nylon 1010 EN-GJS-450-10 NBR/Fluororubber & Backing; EPDM/NBR Vulcanized on Valve Body; Soft Seat in EPDM/NBR; SS304, SS316, AL-Bronze UNC 95400 SS304, SS316, SS416, SS431 EPDM PTFE Aluminum Options

MATERIAL SPECIFICATION Part No. 1 2 3 Part Valve Body Seat Disc Stem O-Ring Bushing Lever Standard Specication EN-GJS-450-10 EPDM EN-GJS-450-10 SS420 NBR Nylon 1010 EN-GJS-450-10 Options NBR SS304, SS316, AL-Bronze UNC 95400 SS304, SS316, SS416, SS431 EPDM PTFE Aluminum

D71XL4 Design Standard: BS EN 593 Connection Ends: BS EN 1092 PN10/PN16 Top Flange Standard: ISO 5211 Stem drive by keys, parallel or diagonal square or at head Working Pressure: PN10/PN16 Temperature Range: 0- 80 Coating: Fusion Bonded Epoxy Coating in accordance with ANSI/AWWA C550
DN Inch 2" 2.5" 3" 4" 5" 6" 8" 10" 12" 14" mm 50 65 80 100 125 150 200 250 300 350 A 140.5 153 157.5 176 191 202.5 243.5 273 311 340

3 4 5 6 7

D41X4 Design Standard: BS EN 593 Face to Face: BS EN 558 Series 13 Connection Ends: BS EN 1092 PN10/PN16 Top Flange standard: ISO 5211 Stem drive by keys, parallel or diagonal square or at head Working Pressure: PN10/PN16 Temperature Range: 0- 80 Coating: Fusion Bonded Epoxy Coating in accordance with ANSI/AWWA C550

4 5 6 7

Note: For special material request other than standard specication, please indicate clearly on the inquiry or order list.

Note: For special material request other than standard specication, please indicate clearly on the inquiry or order list.

Dimensions(mm) B 64.5 72 86 100 112 128 162 194 223 267 C 43 46 46 52 56 56 60 68 78 78 D 53.9 65.2 79.7 105 130 156 206.7 253.3 301.9 333.9 D1 125 145 160 180 210 240 295 355 410 470 V 32 32 32 32 32 32 45 45 45 45 2 14 14 14 16 16 20 26 26 28 31.6 NXM 4XM16 4XM16 8XM16 8XM16 8XM16 8XM20 12XM20 12XM24 12XM24 16XM24 G 9.53 9.53 9.53 11.14 11.14 12.7 20.6 20.6 22.1 22.1 L 267 267 267 267 267 267 356 356 490

ISO 5211 F07 F07 F07 F07 F07 F07 F10 F10 F10 F12

D341X4
DN Inch 2" 2.5" 3" 4" 5" 6" 8" 10" 12" 14" 16" Inch 18" 20" 24" 28" 32" mm 50 65 80 100 125 150 200 250 300 350 400 mm 450 500 600 700 800 L1 108 112 114 127 140 140 152 165 178 190 216 L1 222 229 267 292 318 H1 80 80 95 113 114 139 175 203 242 250 277 H1 295 330 420 450 501 H2 110 131 134 150 170 180 210 245 276 328 376 H2 407 448 518 560 620 H3 32 32 32 32 32 32 45 45 45 45 51 H3 51 64 70 66 66 A 165 185 200 220 250 285 340 405 460 520 580 A 615 670 780 895 1015 B 19 19 19 19 19 19 20 22 24.5 24.5 24.5 B 25.5 26.5 30 32.5 35 C PN16 125 145 160 180 210 240 295 355 410 470 525 C PN10 565 620 725 840 950 20-28 20-28 20-31 24-31 24-34 4-19 4-19 8-19 8-19 8-19 8-23 12-23 12-28 12-28 16-28 16-31 n-1 Dimensions(mm) n-1 D 53.9 65.2 79.7 105 130 156 206.7 253.3 301.9 333.5 389.6 D 440.5 491.6 592.5 695 794.7 E 70 70 70 70 70 70 102 102 102 125 140 E 140 140 165 254 254 K 90 90 90 90 90 90 125 125 125 150 175 K 175 175 210 300 300 n-D2 4-10 4-10 4-10 4-10 4-10 4-10 4-12 4-12 4-12 4-14 4-18 n-D2 4-18 4-18 4-22 8-18 8-18 ISO5211 F07 F07 F07 F07 F07 F07 F10 F10 F10 F12 F14 ISO5211 F14 F14 F16 F25 F25 F 14 14 14 16 16 20 26 26 28 31.6 33.15 F 38 41.15 50.65 63.5 63.5 G 9.53 9.53 9.53 11.14 11.14 12.7 20.6 20.6 22.1 22.1 27 G 27 27 ---L 267 267 267 267 267 267 356 356 490 --L ------

D371XL4

18

19

BS VALVES

BS EN 593 Grooved Buttery Valve (D81X4, D381X4, XD381X4), PN10/16

Buttery Valve Performance Data


Cv = Flow Coefcient Formulas for Cv Values: Cv=Q/(P)0.5 Q = Flow Rate (gal/min) P = Pressure Drop Across Valve (1bf/in2) Kv=Cv/1.156

MATERIAL SPECIFICATION Part No. 1 Part Valve Body Disc O-Ring Stem O-Ring Stem Lever Standard Specication EN-GJS-450-10 EN-GJS-450-10+EPDM NBR SS431 NBR SS431 EN-GJS-450-10 Options NBR EPDM SS304, SS316, SS416 EPDM SS304, SS316, SS416 Aluminum

D81X4

2 3 4 5 6 7

Design Standard: BS EN 593 Connection Ends: Groove to ISO 6182 Top Flange standard: ISO 5211 Stem drive by keys, parallel or diagonal square or at head Working Pressure: PN10/PN16 Temperature Range: 0- 80 Coating: Fusion Bonded Epoxy Coating in accordance with ANSI/AWWA C550 or painting upon request

Flow Rate Q (gal/min)

Note: For special material request other than standard specication, please indicate clearly on the inquiry or order list. DN Inch mm Inch mm Cv Kv 2'' 50 2.06 52.40 284.55 246.15 2.5'' 65 2.50 63.50 417.87 361.48 3'' 80 3.06 77.80 512.16 443.04 4'' 100 4.06 103.00 897.67 776.53 5'' 125 5.04 128.00 1200.59 1038.57 6'' 150 6.06 154.00 1737.86 1503.34 8'' 200 8.06 204.80 3073.50 2658.74 10'' 250 9.90 251.35 4140.73 3581.95 12'' 300 11.81 299.95 5896.80 5101.04

Pipe Diameter Flow Coefcient (Fully Open)

D381X4
DN Inch 2" mm 50 L1 81 L2 15.9 L3 7.9 B 57.15 C 60.3 D 50.3 70 Dimensions(mm) E K 90 n-1 4-10

XD381X4
2 14 ISO 5211 F07

H1 65

H2 89

H3 32

G 9.53

2.5"
2.5" 3" 4" 5"

65
65 80 100 125

97
97 97 116 148

15.9
15.9 15.9 15.9 15.9

7.9
7.9 7.9 9.5 9.5

69.09
72.26 84.94 110.08 135.48

73.0
76.1 88.9 114.3 139.7

60.8
60.8 76 98.5 122.4

70
70 70 70 70

90
90 90 90 90

4-10
4-10 4-10 4-10 4-10

71
71 81 95 111

102
102 109 128 141

32
32 32 32 32

14
14 14 16 16

9.53
9.53 9.53 11.14 11.14

F07
F07 F07 F07 F07

5"
6"

125
150

148
148

15.9
15.9

9.5
9.5

137.03
160.90

141.3
165.1

122.4
148

70
70

90
90

4-10
4-10

111
133

141
153

32
32

16
20

11.14
12.7

F07
F07

6"
8" 10" 12"

150
200 250 300

148
133 159 165

15.9
19.1 19.1 19.1

9.5
11.1 12.7 12.7

163.96
214.40 268.28 318.29

168.3
219.1 273.0 323.9

148
199 252 300.5

70
102 102 102

90
125 125 125

4-10
4-12 4-12 4-12

133
164 196 226

153
184 216 254

32
45 45 45

20
26 31.6 33.1

12.7
20.6 22.1 27

F07
F10 F10 F10

Note: Valve must not be installed with disc in full open position. Disc must be partly closed so that no part is protruding beyond end of valve body.

20

21

BS VALVES

BS Standard Check Valve


Statement: Check valves serve to prevent the backflow of medium in the piping system for protection of important equipments, widely used in the eld of potable water, water supply and drainage, sewage disposal, irrigation, air conditioning, re protection as well as chemical and energy industry. Features: 1. Material: Ductile Iron EN-GJS-450-10 Valve body, bonnet, disc are all produced in ductile iron material which provides guarantee for high strength and good corrosion resistance. 2. Fusion bonded epoxy coating Fusion bonded epoxy coating in accordance with ANSI/AWWA C550 for both interior and exterior surface which provides reliable corrosion resistance. 3. Small hydraulic friction loss with reasonable structure design

BS EN 12334 Swing Check Valve (H44X, H44T), PN10/16

Body & Bonnet: Ductile Iron Disc: D.I.+EPDM or D.I. + Bronze or Stainless Steel Sealing Bronze or Stainless Steel Seat Fusion Bonded Epoxy Coating

H44X
MATERIAL SPECIFICATION

Connection Ends: Flange to BS EN 1092-2:1997 Working Pressure: PN10/PN16 Temperature Range: Rubber Seal: 0- 80, Metal Seal: -10- 350 Coating: Fusion Bonded Epoxy Coating in accordance with ANSI/AWWA C550 or painting upon request

Part No. 1 2 3 4 5 6 7 8

Part Valve Body Seat Ring Disc Clapper Arm Washer Nut Hinge Pin Bonnet Gasket Bolt Washer Bonnet Plug

Standard Specication EN-GJS-450-10 Brass Hpb59-1 (Pressed Fit) EN-GJS-450-10+EPDM EN-GJS-450-10 SS420 Carbon Steel Zinc Plated SS420 EPDM Carbon Steel Zinc Plated Carbon Steel Zinc Plated EN-GJS-450-10 Malleable Iron Galvanized

Options AISI 304, AISI 316 Pressed Fit or Threaded

SS304, SS316 Graphite+Steel SS304, SS316 SS304, SS316

H44X Swing Check Valve Page 23

H44J H84X Grooved Resilient Swing Check Valve Rubber Disc Swing Check Valve Page 25 Page 24

HC41X Silent Check Valve Page 26

DH77X Double Door Wafer Check Valve Page 27

9 10 11 12

Note: For special material request other than standard specication, please indicate clearly on the inquiry or order list. DN Inch 2" 2.5" 3" 4" 5" 6" 8" mm 50 65 80 100 125 150 200 PN 10/16 10/16 10/16 10/16 10/16 10/16 10 16 10 16 10 16 Dimensions(mm) O 203 216 241 292 330 356 495 495 622 622 698 698 D 165 185 200 220 250 285 340 340 405 405 460 460 D1 125 145 160 180 210 240 295 295 350 355 400 410 D2 99 118 132 156 184 211 266 266 319 319 370 370 b 19 19 19 19 19 19 20 20 22 22 24.5 24.5 n-d 4-19 4-19 8-19 8-19 8-19 8-23 8-23 12-23 12-23 12-28 12-23 12-28 f 3 3 3 3 3 3 3 3 3 3 4 4 H 146 155 173 180 212 260 290 290 339 339 376 376

10"

250

12"

300

22

23

BS VALVES

Grooved Resilient Swing Check Valve (H84X), PN10/16

BS EN 12334 Rubber Disc Swing Check Valve (H44J), PN10/16

MATERIAL SPECIFICATION Part No. 1 2 3 Part Valve Body Hinge Pin Spring Eye Bolt Disc Disc Sealing Ring Seat Ring Plug Plug Plug Plug Bolt Washer Nut Standard Specication EN-GJS-450-10 SS420 SS304 Carbon Steel Zinc Plated EN-GJS-450-10 EPDM ASTM B62 C83600 (Pressed Fit) Malleable Iron Galvanized Malleable Iron Galvanized Malleable Iron Galvanized Malleable Iron Galvanized SS304 SS304 SS304 SS304 NBR SS304, SS316 Pressed Fit or Threaded Bronze ASTM B584 Bronze ASTM B584 Bronze ASTM B584 Bronze ASTM B584 SS316 SS316 SS316 DN Inch 2" B 7.93 C 15.88 2.5" 3" 4" 6" 8" 10" 12" mm 50 65 80 100 150 200 250 300 SS316 Options

H84X Connection Ends: Groove to ISO 6182 Working Pressure: PN10/PN16 Temperature Range: 0- 80 Coating: Fusion Bonded Epoxy Coating in accordance with ANSI/AWWA C550 or painting upon request

4 5 6 7 8 9 10 11 12 13 14

H44J
MATERIAL SPECIFICATION Part No. 1 Part Valve Body Bolt Washer Disc Bonnet Bonnet Gasket Plug Standard Specication EN-GJS-450-10 Carbon Steel Zinc Plated Carbon Steel Zinc Plated Carbon Steel + EPDM EN-GJS-450-10 EPDM Malleable Iron Galvanized Bronze ASTM B584 SS304, SS316 SS304, SS316 Carbon Steel+NBR Options

Connection Ends: Flange to BS EN 1092-2:1997 Working Pressure: PN10/PN16 Temperature Range: 0- 80 Coating: Fusion Bonded Epoxy Coating in accordance with ANSI/AWWA C550

2 3 4 5 6 7

Note: For special material request other than standard specication, please indicate clearly on the inquiry or order list. PN 10/16 10/16 10/16 10/16 10/16 10 16 10 16 10 16 Dimensions(mm) L 203 216 241 292 356 495 495 622 622 698 698 D 165 185 200 220 285 340 340 405 405 460 460 D1 125 145 160 180 240 295 295 350 355 405 410 d 99 118 132 156 211 266 266 319 319 370 370 C 19 19 19 19 19 20 20 22 22 24.5 24.5 T 3 3 3 3 3 3 3 3 3 4 4 n-L 4-19 4-19 8-19 8-19 8-23 8-23 12-23 12-23 12-28 12-23 12-28

Note: For special material request other than standard specication, please indicate clearly on the inquiry or order list. DN Inch 2" mm 50 PN 16 Dimensions(mm) L 171 D1 57.15 D2 60.3

2.5"
2.5" 3" 4" 5"

65
65 80 100 125

16
16 16 16 16

184
184 197 210 248

69.09
72.26 84.94 110.08 135.48

73
76.1 88.9 114.3 139.7

7.93
7.93 7.93 9.53 9.53

15.88
15.88 15.88 15.88 15.88

5"
6"

125
150

16
16

248
324

137.03
160.90

141.3
165.1

9.53
9.53

15.88
15.88

6"
8" 10" 12"

150
200 250 300

16
16 16 16

324
371 457 535

163.96
214.40 268.28 318.29

168.3
219.1 273.0 323.9

9.53
11.13 12.70 12.70

15.88
19.05 19.05 19.05

24

25

BS VALVES

Silent Check Valve (HC41X), PN10/16

Double Door Wafer Check Valve (DH77X), PN10/16

HC41X Connection Ends: Flange to BS EN 1092-2:1997 Working Pressure: PN10/PN16 Temperature Range: 0- 80 Coating: Fusion Bonded Epoxy Coating in accordance with ANSI/AWWA C550

MATERIAL SPECIFICATION Part No. 1 2 3 4 5 6 7 8 9 10 11 Part Valve Body Stem Hinge Bushing Spring Nut Disc O-Ring Hinge bushing Seat O-Ring Screw Standard Specication EN-GJS-450-10 SS420 Brass Hpb59-1 SS304 SS304 EN-GJS-450-10 EPDM Brass Hpb59-1 EN-GJS-450-10 NBR Carbon Steel Zinc Plated EPDM SS304, SS316 NBR SS316 SS316 SS304, SS316, SS431 Options

DH77X
MATERIAL SPECIFICATION

Connection Ends: BS EN 1092 PN10/PN16, AS 2129 TABLE E, JIS B2212 10K, BS 10 TABLE D/E Working Pressure: PN10/PN16 Temperature Range: 0- 80 Coating: Fusion Bonded Epoxy Coating in accordance with ANSI/AWWA C550

Part No. 1 2 3 4 5

Part Valve Body Disc Stem Spring Rubber Seat

Standard Specication EN-GJS-450-10 EN-GJS-450-10+EPDM SS420 SS304 EPDM

Options

SS304, SS316, AL-Bronze UNC 95400 SS304, SS316, SS416 SS316 NBR

Note: For special material request other than standard specication, please indicate clearly on the inquiry or order list. DN Inch 2" 2.5" 3" 4" 5" 6" 8" 10" 12" 14" 16" mm 50 65 80 100 125 150 200 250 300 350 400 PN 10/16 10/16 10/16 10/16 10/16 10/16 10/16 10/16 10/16 10/16 10/16 Dimensions(mm) L 54 54 57 64 70 76 95 108 143 184 191 D 107 127 142 162 192 218 273 328 378 438 489 D1 64 78 94 117 145 170 224 265 310 360 410 D2 46 60 70 84 115 134 184 220 260 302 350

Note: For special material request other than standard specication, please indicate clearly on the inquiry or order list. DN Inch 2" 2.5" 3" 4" 5" 6" 8" 10" 12" mm 50 65 80 100 125 150 200 250 300 L 120 135 155 165 190 210 260 285 315 D 165 185 200 220 250 285 340 405 460 D1 125 145 160 180 210 240 295 355 410 Dimensions(mm) D2 99 118 132 156 184 211 266 319 370 C 19 19 19 19 19 19 20 22 24.5 T 3 3 3 3 3 3 3 3 4 n-L 4-19 4-19 8-19 8-19 8-19 8-23 12-23 12-28 12-28

26

27

BS VALVES

BS Standard Y-Type Strainer


Statement: Installed before relief valves, atmospheric valves, hydraulic control valves as well as other equipments, strainers serve to lter out the impurities in the ow medium for protection of valves and equipments in the piping system. Features: 1. Material: Ductile Iron EN-GJS-450-10 Valve body and cover are produced in ductile iron material which provides guarantee for high strength and good corrosion resistance. 2. Different Options of Screen Mesh Specication Different options of screen mesh specification available as per different service conditions. 3. Fusion Bonded Epoxy Coating Fusion bonded epoxy coating in accordance with ANSI/AWWA C550 for both interior and exterior surface which provides reliable corrosion resistance.

Y-Type Strainer (V4), PN10/16, UL Listed

Ductile Iron Body & Bonnet Stainless Steel Screen Fusion Bonded Epoxy Coating Gasket: EPDM or Graphite + Acanthopore Plate

V4

MATERIAL SPECIFICATION Part No. 1 2 Part Valve Body Screen Gasket Bonnet Plug Bolt Flat Washer Standard Specication EN-GJS-450-10 SS304 (Perforated) EPDM EN-GJS-450-10 Malleable Iron Galvanized Carbon Steel Zinc Plated Carbon Steel Zinc Plated Bronze ASTM B584 SS304, SS316 SS304, SS316 Options SS304, SS316 (Perforated, Knitted, Double Screen) Graphite+Acanthopore Plate

Connection Ends: Flange to BS EN 1092-2:1997 Working Pressure: PN10/PN16 Temperature Range: 0- 80 rubber gasket, -10- 350 graphite gasket Coating: Fusion Bonded Epoxy Coating in accordance with ANSI/AWWA C550

3 4 5 6 7

STANDARD SCREEN DN Inch 2"~2.5" 3"~4" 5" 6"~12" mm 50~65 80~100 125 150~300 Sieve No. 25 19 14 13 Hole Dia. mm 4 5 6 6.3 Free Flow Area(%) % 48 59 63 64

V4 Y-Type Strainer Page 29

V8 Grooved Y-Type Strainer Page 30


Inch 1.5" 2" 2.5" 3" 4" 5" 6" 8" 10" 12" 14" 16"

Note: For special material request other than standard specication, please indicate clearly on the inquiry or order list. DN mm 40 50 65 80 100 125 150 200 250 300 350 400 PN 10/16 10/16 10/16 10/16 10/16 10/16 10/16 10 16 10 16 10 16 10 16 10 16 Dimensions(mm) L 200 230 290 310 350 400 480 600 730 850 838 864 D 150 165 185 200 220 250 285 340 405 460 520 580 D1 110 125 145 160 180 210 240 295 350 355 400 410 460 470 515 525 D2 90 99 118 132 156 184 211 266 319 370 429 480 b 19 19 19 19 19 19 19 20 22 24.5 26.5 28 n-d 4-19 4-19 4-19 8-19 8-19 8-19 8-23 8-23 12-23 12-23 12-28 12-23 12-28 16-23 16-28 16-28 16-31 f 3 3 3 3 3 3 3 3 3 4 4 4 H 140 140 175 198 229 287 304 370.5 469 540 625 715

28

29

BS VALVES

Grooved End Y-Type Strainer (V8), PN10/16/25


Connection Ends: Groove to ISO 6182 Working Pressure: PN10/PN16/PN25 Temperature Range: 0- 80 Coating: Fusion Bonded Epoxy Coating in accordance with ANSI/AWWA C550 or painting upon request

Hydraulic Control Valves, PN10/16/25


Statement The hydraulic control valve was initially originated in Holand, Israel and Denmark, used for agricultural irrigation. Later the product was introduced into the United Sates, Canada and Asian countries. It was from the 1990s when the product first entered China, and ever since its entrance it gets rapidly developped and widely applied in different industrie aside from irrigation. The hydraulic control valve produced by Jinan Meide is new style that absorbed the essence of other well-known brands which makes it better in energy saving, consumption reducing and accurate adjusting achieving. The MECH brand hydraulic control valves have been widely used in China, Europe and South East Asian countries in pipe system of irrigation, water supplying, re protection and air conditioning which has medium of water under 80 or other medium with similar physical and chemical property as water. Specications Basic Valve: Y-Type Direct-ow Connection Ends: Flange to BS EN 1092-2:1997 Temperature Range: 0- 80 (0 - 180) Working Pressure: PN10/PN16/PN25 Testing Standard: API 598 Flow Diagram of Basic Valve
Water Head Loss (psi)

Cap Plug (Brass H62) Up Bonnet (EN-GJS-450-10) Up Gland (EN-GJS-450-10) Diaphragm (EPDM) Bottom Gland (EN-GJS-450-10) Bushing (Brass H62) Middle Bonnet (EN-GJS-450-10) Stem (SS304) Bolt (SS304) Spring ( Stainless Steel 4Cr13) Main Disc (EN-GJS-450-10) Main Gasket (EPDM) Gland of Main Disc (EN-GJS-450-10) Seat (SS304) Valve Body (EN-GJS-450-10)

MATERIAL SPECIFICATION Part No. 1 2 3 4 5 Part Valve Body Screen Rigid Coupling Cap Plug Standard Specication EN-GJS-450-10 SS304 EN-GJS-450-10 EN-GJS-450-10 Malleable Iron Galvanized Bronze ASTM B584 SS316 Options

DN50 DN65

Flow Rate (gpm)

STANDARD SCREEN DN Inch 2"~2.5" 3"~4" 5" 6"~12" mm 50~65 80~100 125 150~300 Sieve No. 25 19 14 13 Hole Dia. mm 4 5 6 6.3 Free Flow Area(%) % 48 59 63 64

DN80 DN100 DN125 DN150

DN200 DN250 DN300 DN350 DN400 DN450 DN500 DN600

Note: For special material request other than standard specication, please indicate clearly on the inquiry or order list. DN Inch 2" mm 50 L 247.5 OD 60.3 Dimensions(mm) d 57.15 A 15.88 B 7.92

2.5"
2.5" 3" 4" 5"

65
65 80 100 125

273
273.0 298.5 362.0 419.0

73
76.1 88.9 114.3 139.7

69.09
72.26 84.94 110.08 135.48

15.88
15.88 15.88 15.88 15.88

7.92
7.92 7.92 9.52 9.52 DN Inch 2" 2.5" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" mm 50 65 80 100 150 200 250 300 350 400 450 500 DN
Kv

50 41

65 53

80 105

100 175

125 285

150 402

200 730

250 1160

300 1400

350 1770

400 3010

450 3225

500 3395

5"
6"

125
150

419
470.0

141.3
165.1

137.03
160.90

15.88
15.88

9.52
9.52

PN 10/16 10/16 10/16 10/16 10/16 10 16 10 16 10 16 10 16 10 16 10 16 10 16

Dimensions(mm) L 203 216 241 292 356 495 495 622 622 698 698 787 787 914 914 978 978 1100 1100 H 170 195 215 255 360 450 550 645 700 790 850 900 D 165 185 200 220 285 340 340 405 405 460 460 505 520 565 580 615 640 670 715 D1 125 145 160 180 240 295 295 350 355 400 410 460 470 515 525 565 580 620 625 d 99 118 132 156 211 266 266 319 319 370 370 429 429 480 480 530 548 582 609 C 19 19 19 19 19 20 20 22 22 24.5 24.5 24.5 26.5 24.5 28 25.5 30 26.5 31.5 T 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 n-L 4-19 4-19 8-19 8-19 8-23 8-23 12-23 12-23 12-28 12-23 12-28 16-23 16-28 16-28 16-31 20-28 20-31 20-28 20-34

6"
8" 10" 12"

150
200 250 300

470.0
609.5 686.0 762.0

168.3
219.1 273.0 323.9

163.96
214.40 268.28 318.29

15.88
19.05 19.05 19.05

9.52
11.13 12.70 12.70

Important notes: 1.The products listed in this catalogue are intended to be assembled only in pipelines of same or lower pressure ratings and properly installed. In case of special request, please contact with factory for support and conrm. 2.It can happen that the catalogue might not be updated while product design improved. In this case, design of the product should be as conrmed when order placed. 3.Jinan Meide Casting Co., Ltd. reserves the right for construe of the information provided in this catalogue

30

31

BS VALVES

SK710X Electromagnetic Control Valve

1. Statement SK710X Electromagnetic Control Valve is a diaphragm type of hydraulic control valve driven by the hydraulic pressure within the piping system. This type of valve is widely applied in the eld of piping system optimization, pressure division, water reservoir (tank) backup, change of industrial valves, etc., with its closing and opening remotely controlled by electric signal. 2. Operational principle SK710X Electromagnetic Control Valve is controlled by solenoid valve and equipped with normally open (or normally closed) two positions two ways or two positions three ways solenoid pilot valve, needle valve, mini strainer and ball valve, etc. When the normally open solenoid valve is applied, the main valve in most cases will be in open position. When there is pressure coming from the ow direction, Pressure P1 enters the upper cavity room of the valve through the guide tube and then comes to the low pressure area through the normally open solenoid valve. In this way the upper cavity room is not able to form conned space and the disc of the main valve will be opened at the pressure of P1. When the normally open solenoid valve is closed, pressure P1 will be accumulated inside the upper cavity which will gradually push the membrane to close the disc and the valve. For normally closed solenoid valve, the main valve will be in most cases closed and operation principle same as stated above. The application of the solenoid valve depends on the working environment. In case the water inside the piping system are highly corrosive or with high deposits, user can choose also to control the valve with medium from outside. It's up to the option of the client, depending on different working conditions. 3.Property and advantages Driven by pressure of pipe system, work automatically without any power-generating. It saves installation and repairing space. Controlled by solenoid valve, save energy and wiring costs, can be used for large range of pressure and voltage. Series of mode of execution can be changed to hand control, normally closed solenoid valve control or normally open solenoid valve control, etc. Dual cavity design, with functions of fully opening and fully closing. Slow shut causes no pressure uctuation, and the diaphragm with support is well protected. Channel with straight-ow, slight friction loss, no eddy ow and turbulent ow. Long pitch orientation design for stem move, stable and no gap resistance. Balanced automatically, big gap design on connection of disc and stem, disc is free on the vertical at against stem, it can balance the tolerance from machining and sealing surface. Good connection without leakage. Ductile iron castings with nodularity higher than 90%, foundry in house with advanced melting technology and strict quality control system, testing reports and testing bars can be supplied with order. Records and testing bars maintained for one year in the factory. Good corrosion resistance, with stainless steel, copper alloy, rubber made from DuPont and other rustresisting material, fusion bonded epoxy coating both for interior and exterior surface of the basic valve. All the characteristics in accordance with ANSI/AWWA C550 and other international specications like WRAS, NSF61.

4. Typical installation illustration

5. Common problems and proposed solutions


Common Problems Pressurize in front of the valve but valve can't be opened when choose condition of normally open and no power. The basic valve can't be closed when choose normally open and shut down the power. Pressure in front and the valve can't close complete with leakage when choose condition of normally close and no power. No water after valve, valve is not open when choose condition of normally close and electried. Proposed Solutions Check if needle valve or ball valve in front of the basic valve is opened. If not, please open it. Check condition of wiring, make sure action in place and for the solenoid valve and sealing is good condition for the solenoid valve. Check if there's sundries blocked inside the basic valve. Wash the mini strainer before basic valve and make sure it's unblocked. Check if any damage or blocks on the sealing surface of basic valve. Check if solenoid valve is in good working condition. Check if needle valve or ball valve is open in front of the valve.

32

33

BS VALVES

SK720X Pressure Reducing Valve

1.Statement SK720X Pressure Reducing Valve is a diaphragm type of hydraulic control valve driven by the hydraulic pressure within the piping system. The function of the valve is to reduce the high pressure to the pre-set low pressure, and despite the uctuation of medium ow or pressure before the valve the pressure after the valve will always remain stable and maintain the set pressure range. 2.Operational principle SK720X Pressure Reducing Valve is controlled by pressure reducing pilot valve and equipped with pressure reducing pilot valve, needle valve, mini strainer and ball valve, etc. Under normal conditions, water ow comes continuously from the inlet opening to the upper cavity room (2) of the basic valve through the needle valve (1); When the pressure before the pilot valve (3) is lower than its pre-set value, the pilot valve will remain at full open position and the upper cavity room of the basic valve is not able to get accumulating pressure. Under this condition, the disc of the basic valve will be open at the water pressure from the inlet opening to allow water ow. The pressure reducing pilot valve closes gradually when the pressure after pilot valve exceeds its pre-set value. Pressure gets accumulated within the upper cavity room and membrane drives the disc down to close the valve till the pressure after the pilot valve gradually reduces to its pre-set value. The pilot valve opens again when the pressure after the valve becomes lower than the pre-set value, and the basic valve will then open with the release of the accumulated pressure in the upper cavity room. The throttle orice (5) that connects the lower cavity to the outlet serves to keep the reaction of the valve gentle and stable. The ball valve (4) controls the outlet water ow rate from the upper cavity room and thus to stabilize the action of the basic valve. The ball valve can be adjusted with different working conditions. In case of emergency, the ball valve can also be closed manually for cutting off of the basic valve. 3.Property and advantages Driven by pressure of pipe system, work automatically with energy of pipe system to achieve energy conservation and environment protection. Controlled by the pilot valve, lower energy consumption, achieve accurate pressure reducing results, have function of stabilizing pressure after the valve. Dual cavity design, with functions of fully opening and fully closing. Slow shut causes no pressure uctuation, and the diaphragm with support is well protected. Have internal orice, connect bottom cavity and outlet of the basic valve, make sure stability of reaction to keep stability of pressure after the valve, avoid any vibration and noise. Channel with straight-ow, slight friction loss, no eddy ow and turbulent ow, cut down the damage of cavitation. Long pitch orientation design for stem move, stable and no gap resistance. Balanced automatically, big gap design on connection of disc and stem, disc is free on the vertical at against stem, it can balance the tolerance from machining and sealing surface. Good connection without leakage. Achieve functions of both reducing dynamic pressure and reducing static pressure. Ductile iron castings with nodularity higher than 90%, foundry in house with advanced melting technology and strict quality control system, testing reports and testing bars can be supplied with order. Records and testing bars maintained for one year in the factory. Good corrosion resistance, with stainless steel, copper alloy, rubber made from DuPont and other rustresisting material, fusion bonded epoxy coating both for interior and exterior surface of the basic valve. All the characteristics in accordance with ANSI/AWWA C550 and other international specications like WRAS, NSF61.

4.Typical installation illustration

5.Basic Parameters
Pressure Max. Inlet pressure Min. Inlet pressure Max. Outlet pressure Min. Outlet pressure Characteristics of ow deviation Pressure characteristic deviation Min. pressure deviation Symbol P1max P1min P2max P2min P2Q P2p Pmin MPa 0.8 Unit Nominal Pressure PN10 1.0 PN16 1.6 P2max + 0.2 1.0 0.05 10% 5% 0.2 1.6 PN25 2.5

6.Notes for installation and debugging All the Pressure Reducing Valves have been finished initial debugging tests before delivery. Further dubugging test is also suggested during using according to different working conditions. After the pipe system becomes stable, please loose the adjusting screw on the top of pilot valve to the top-most position. Tighten adjusting screw of pilot valve in clockwise slowly. When outlet pressure increase to the set pressure please fasten the locknut under the adjusting screw. If go beyond the set pressure during adjusting, please repeat the above steps. Remember, pressure can be only adjusting from low level to high level and pay attention to make the adjusting slowly.

7.Common problems and proposed solutions


Common Problems Proposed Solutions a.Check if any sundries on the sealing surface of basic valve or pilot valve. b.Check if any damage on the sealing surface of basic valve or pilot valve. c.Check if any damage or fatigue on spring of basic valve or pilot valve. d.Check if any damage or fatigue on diaphragm of basic valve or pilot valve. e.Check if any corrosion or blocking on stem of basic valve or pilot valve. a.Close the needle valve before the basic valve and open 1/4 turns slowly. Open the big hex screw on the top of bonnet, release air. Adjust the needle valve on inlet conduit slowly until no vibration. b.Calculate the ow again and collect proper size of valve or add throttling set. a.Check if pressure is uctuating strongly at inlet. Try to keep it within small range. b.Check if required ow is too different than actual ow, recalculate ow and choose new valve with proper size.

Outlet pressure is similar with inlet pressure, no pressure reduction.

Strong vibration and noise.

Pressure after the valve is not stable.

34

35

BS VALVES

SK730X Pressure Relief & Sustaining Valve

1.Statement SK730X Pressure Relief & Sustaining Valve is a diaphragm type of hydraulic control valve driven by the hydraulic pressure within the piping system. One prominent feature of the valve is, it can serve as pressure relief valve and sustaining valve at the same time. As pressure relief valve, it releases the high pressure before the valve out of the piping system for protection of the pipes and the equipments when the pressure exceeds its pre-set value; As pressure sustaining valve, it maintains the water pressure above certain set value for guarantee of water supply to upstream area 2.Operational principle SK730X Pressure Relief & Sustaining Valve is controlled by pressure relief/sustaining pilot valve and equipped with pressure relief/sustaining pilot valve, needle valve, mini strainer and ball valve, etc. As Pressure relief valve, the valve is connected with branch pipe and directed to lower pressure area or drainage ditch. In normal working conditions, water ow enters the upper cavity room (2) through needle valve (1). When the pressure before the pilot valve (3) is lower than its pre-set value A, the pilot valve will remain closed and the water that enters the upper cavity room drives the membrane down and closes the disc and the basic valve. The pilot valve opens when the pressure before the valve exceeds its pre-set value and the pressure accumulated in the upper cavity room gets released. Under the pressure from the inlet opening, the disc of the basic valve opens. In this way the pressure within the piping system will be maintained under the pre-set value A. As pressure sustaining valve, the valve is connected in series with the main pipe and serves to maintain the pressure before valve above the set value B. Under normal conditions, water ow comes continuously from the inlet opening to the upper cavity room (2) of the basic valve through the needle valve (1); When the pressure before the pilot valve (3) is lower than its pre-set value, the pilot valve will remain closed and the water that enters the upper cavity room drives the membrane down and closes the disc and the basic valve for accumulation of pressure till equals to the set value B. The pilot valve opens when the pressure before the valve exceeds its pre-set value and the pressure accumulated in the upper cavity room gets released. Under the pressure from the inlet opening, the disc of the basic valve opens to allow water ow. In this way the pressure within the piping system will be maintained under the pre-set value B. 3.Property and advantages Driven by pressure of pipe system, work automatically with energy of pipe system to achieve energy conservation and environment protection. Controlled by pilot valve, lower energy consumption, achieve accurate pressure relief and pressure holding results, reliable and safe. Dual cavity design, with functions of fully opening and fully closing. Slow shut causes no pressure uctuation, and the diaphragm with support is well protected. Have internal orice, connect bottom cavity and outlet of the basic valve, make sure stability of reaction to keep stability of pressure after the valve, avoid any vibration and noise. Channel with straight-ow, slight friction loss, no eddy ow and turbulent ow, cut down the damage of cavitation. Long pitch orientation design for stem move, stable and no gap resistance. Balanced automatically, big gap design on connection of disc and stem, disc is free on the vertical at against stem, it can balance the tolerance from machining and sealing surface. Good connection without leakage. Ductile iron castings with nodularity higher than 90%, foundry in house with advanced melting technology and strict quality control system, testing reports and testing bars can be supplied with order. Records and testing bars maintained for one year in the factory. Good corrosion resistance, with stainless steel, copper alloy, rubber made from DuPont and other rustresisting material, fusion bonded epoxy coating both for interior and exterior surface of the basic valve. All the characteristics in accordance with ANSI/AWWA C550 and other international specications like WRAS, NSF61.

4.Typical installation illustration

For Pressure Relief

For Pressure Sustaining

5.Basic Parameters
Norminal Pressure Pressure Symbol Unit PN10 Set Pressure Set Pressure Difference Open/Close Pressure Difference Discharge pressure Pb Ps MPa 0.83 PN16 1.33 Ps0.5: 0.014 MPa; Ps0.5: 3%Ps Ps0.3: 0.06MPa; Ps0.3: 20%Ps 1.2Ps PN25 1.7

6.Notes for installation and debugging All the Pressure Relief & Sustaining Valves have been nished initial debugging tests before delivery and the set-pressure is 0.6MPa. Further debugging test is also suggested during using according to different working conditions. After the pipe system becomes stable, please loose the lock nut under adjusting screw, open the ball valve or needle valve (1) slightly, when pressurize, adjust the adjust screw on pressure relief pilot valve and fasten the lock nut when it achieves pressure required. Pay attention that when adjust pressure relief pilot valve, clockwise is for increasing pressure and anti-clockwise is for reducing pressure.

Pd

7.Common problems and proposed solutions


Common Problems The pressure of pipe system is lower than set-pressure, the valve dose not close. Proposed Solutions a.Check if any sundries on the sealing surface of basic valve or pilot valve. b.Check if any damage on the sealing surface of basic valve or pilot valve. c.Check if any damage or fatigue on spring of basic valve or pilot valve. d.Check if any damage or fatigue on diaphragm of basic valve or pilot valve. a.Check if ball valve (4) is closed, if yes, please open it. b.Check if any blocks in basic valve or on stem of pilot valve, if yes, please remove the block or change new stem. c.Check if lock nut and adjust screw were adjusted wrongly, please try to repeat all the actions.

The pressure of pipe system is higher than set-pressure, the valve dose not open.

36

37

BS VALVES

SK750X Remote Float Control Valve

1.Statement SK750X Remote Float Control Valve is a diaphragm type of hydraulic control valve driven by the hydraulic pressure within the piping system, designed with adjustable parallel oat. The valve is capable to maintain the water surface at set position despite the uctuation of ow rate and widely applied where there is water reservoir or water box for injection of water. 2.Operational principle SK750X Remote Float Control Valve is controlled by angle valve, oat and ball lever, and equipped with needle valve, mini strainer and ball valve, etc. Under normal conditions, water ow comes continuously from the inlet opening to the upper cavity room (2) of the basic valve through the needle valve (1); When the oat is not reaching the set position, the angle valve 4 remains open. The water that enters the upper cavity room of the basic valve discharges into the water tank and no accumulation within. Under this condition, the disc of the basic valve remains open at the water pressure from the inlet opening to allow water supply to the water tank. With the raising of the water surface, the oat (6) gradually raises and closes the angle valve (4). Pressure gets accumulated within the upper cavity room and drives the membrane down to close disc and the basic valve gradually. When the water surface reaches the set position, the angle valve close completely and so with the basic valve and the water supply stops. When water position declines, the pressure within the upper cavity room gets released through the angle valve and the basic valve opens to continue with water supply. Needle valve (1) serves to control the closing speed of the valve to prevent formation of water hammer; In case the oat is not working, ball valve (3) can close the basic valve for emergency cut-off. 3.Property and advantages Driven by pressure of pipe system, work automatically with energy of pipe system to achieve energy conservation and environment protection. Controlled by angle valve and oat, lower energy consumption, achieve accurate level limit, slowly shut and avoid close valve water hammer. Separate angle control, including separate angle valve, ball lever and oat, can be installed separately with basic valve, suitable for limited installation and repairing space, avoid inuence to level measuring by the wave beside inlet water. Dual cavity design, with functions of fully opening and fully closing. Slow shut causes no pressure uctuation, and the diaphragm with support is well protected. Have internal orice, connect bottom cavity and outlet of the basic valve, make sure stability of reaction to keep stability of pressure after the valve, avoid any vibration and noise. Channel with straight-ow, slight friction loss, no eddy ow and turbulent ow, cut down the damage of cavitation. Long pitch orientation design for stem move, stable and no gap resistance. Balanced automatically, big gap design on connection of disc and stem, disc is free on the vertical at against stem, it can balance the tolerance from machining and sealing surface. Good connection without leakage. Achieve functions of both reducing dynamic pressure and reducing static pressure. Ductile iron castings with nodularity higher than 90%, foundry in house with advanced melting technology and strict quality control system, testing reports and testing bars can be supplied with order. Records and testing bars maintained for one year in the factory. Good corrosion resistance, with stainless steel, copper alloy, rubber made from DuPont and other rustresisting material, fusion bonded epoxy coating both for interior and exterior surface of the basic valve. All the characteristics in accordance with ANSI/AWWA C550 and other international specications like WRAS, NSF61.

4.Typical installation illustration

5.Technical Parameter
Accuracy of Surface Control: 25mm

6.Common problems and proposed solutions


Common Problems Proposed Solutions a.Check if any sundries on the sealing surface of basic valve or pilot valve. b.Check if any damage on the sealing surface of basic valve or pilot valve. c.Check if block on lever of controlling angle valve. d.Check if ball lever has been corrosive and oat missing. e.Check if any damage for diaphragm. During the checking, please close ball valve (3), if the basic valve was closed, please just disregard method of a, b and e and only check sealing surface of angle valve and ball lever. If the basic valve does not close when close ball valve (3), please cut off the water supply and check sealing surface of basic valve, diaphragm and stem. If any damaged parts, please change new one. a.Check if the oat was installed close to water outlet. If yes, please move it to far away from the water outlet. Or you can use barrel to avoid the affection of the wave. b.Check the location of oat and make sure the top-most position which oat can catch is the set-level of the water box. To make sure water won't exceed set-level double insurances is recommended. That's to assemble two position two-way solenoid valve before the controlling angle valve to make sure that the valve can be closed in case of emergency.

Basic valve does not close when water meets specified level and continue to supply water.

Level adjusting is not accurate and oat jumps strongly.

Reasonable suggestion

38

39

BS VALVES

SK760X Slow Shut Control Valve (Pump Control Valve)

1.Statement SK760X Slow Shut Control Valve (Pump Control Valve) is a diaphragm type of hydraulic control valve driven by the hydraulic pressure within the piping system, widely applied in the pump outlet for prevention of medium back-ow, pressure uctuation and water hammer formation. Under normal working conditions, pressure before the valve is higher than pressure after, and the valve remains fully open. When pressure after valve exceeds pressure before valve, the valve is capable to be closed rapidly to prevent backow of water and protect the pump and piping system. The design of the valve incorporates the function of slowopening, quick closing, slow closing and water hammer absorption, no large pressure uctuation within the system. 2.Operational principle SK760X Slow Shut Control Valve (Pump Control Valve) is composed of needle valve (or ball valve), mini strainer and ball valve, etc. Before the pump starts, there is no pressure before the valve, and disc (5) is closed under the pressure from the spring. With the start of the pump, the pressure before the valve increases gradually. At the same time, the pressure water enters the lower cavity room (2) through the needle valve (1) (or ball valve). The two combined force opens the disc of the basic valve rapidly to allow water supply. When the pump stops (as planned or out of accident), pressure before the valve suddenly declines. Pressure after valve exceeds that before the valve. As a result, the higher pressure ows back to the upper cavity room through the needle valve (4) (or ball valve) and gets accumulated to drive the membrane down to close the valve disc (5). The pressure within the lower cavity room (2) discharges to the lower pressure area before the basic valve through needle valve (1) (or ball valve) , which slows down the closing process to prevent formation of water hammer. The opening and closing speed of the valve can be controlled by adjustment of the needle valve (1) & (4) (or ball valve). The valve is designed with dual disc, especially good for working in complicated piping system and working conditions where there is tremendous pressure and water back-ow. 3.Property and advantages Driven by pressure of pipe system, work automatically with energy of pipe system to achieve energy conservation and environment protection. Dual cavity design, with functions of fully opening and fully closing. Slow shut causes no pressure uctuation, and the diaphragm with support is well protected. Stable when open and close, the speed of opening and closing can be adjusted according to working conditions to avoid pressure uctuation and water hammer. It can achieve real silence. Dual disc, customer can choose design of main disc + second disc. Main disc will fall freely with its weight when pump stop working, then 90% of inlet of basic valve will be will closed, the water will not cause pump reversing. The second disc will close the 10% left slowly by the pressure of controlling cavity then huge energy of water hammer will be eliminated. Channel with straight-ow, slight friction loss, no eddy ow and turbulent ow, cut down the damage of cavitation. Long pitch orientation design for stem move, stable and no gap resistance. Balanced automatically, big gap design on connection of disc and stem, disc is free on the vertical at against stem, it can balance the tolerance from machining and sealing surface. Good connection without leakage. Achieve functions of both reducing dynamic pressure and reducing static pressure. Ductile iron castings with nodularity higher than 90%, foundry in house with advanced melting technology and strict quality control system, testing reports and testing bars can be supplied with order. Records and testing bars maintained for one year in the factory. Good corrosion resistance, with stainless steel, copper alloy, rubber made from DuPont and other rustresisting material, fusion bonded epoxy coating both for interior and exterior surface of the basic valve. All the characteristics in accordance with ANSI/AWWA C550 and other international specications like WRAS, NSF61.

4.Typical installation illustration

5.Technical Parameter
Pressure Min Closing Pressure Slow-shut Time Symbol Pg t Unit MPa s Norminal Pressure PN10 PN16 0.05 260 PN25

Note: Slow-shut time can be adjusted as per request

6.Common problems and proposed solutions


Common Problems Strong vibration and noise when start-up the pump. Strong vibration and noise when stop the pump. Proposed Solutions a.Check if there's gas in the upper cavity room. Loose the hex brass nut on the top of bonnet to discharge gas. b.Adjust the needle valve or ball valve (1) at inlet to proper opening speed. c.Recalculate the ow and choose new valve with proper size or add throttling set. a.Adjust needle valve or ball valve (4) to proper closing speed. b.Consider to choose design of dual discs. a.Check if there's sundries on the sealing surface of main disc or second disc. b.Check if damage on sealing surface of main disc or second disc. c.Check if stem corroded or blocked. d.Check if damage on diaphragm. If any damaged parts found, please change new one.

Valve does not work and cause pump's reversing.

40

41

BS VALVES

SK780X Pressure Differential By-pass Balancing Valve

1.Statement SK780X Pressure Differential By-pass Balancing Valve is a diaphragm type of hydraulic control valve driven by the hydraulic pressure within the piping system, widely applied in HVAC system for guarantee of ow stability in the air conditioning, refrigeration and heating system and pump working. The valve prevents the effect on the other pipe branches when there is uctuation on one branch by balancing of pressure in the radiant and distribution water manifold, thus to protect the efcient and safe working of the refrigeration set or heating set. 2.Operational principle SK780X Pressure Differential By-pass Balancing Valve is composed of pressure balancing pilot valve, needle valve (or ball valve), mini strainer and ball valve, etc. SK780X Pressure Differential By-pass Balancing Valve is installed between radiant and distribution water manifold (water supply and water return). Water ow enters continuously from water supply duct to the valve inlet and then to the upper cavity room (2) through needle valve (1) (or ball valve). Pilot valve (3) is connected to the water supply duct and return duct by guide tube (4) and (5) to sensing of the pressure difference and adjustment of the opening position of the pilot valve accordingly. When the pressure difference is large, pilot valve opens broadly, the pressure inside upper cavity room (2) declines and the basic valve opens broadly. As result the water ow between the supply and return duct increase and the entire system gets balanced. When the pressure difference is small, pilot valve (3) turns to close at the pressure of the spring, the pressure inside upper cavity room (2) increase and the basic valve turns to close. As result the water ow between the supply and return duct decreases and the entire system also gets balanced. 3.Property and advantages Driven by pressure of pipe system, work automatically with energy of pipe system to achieve energy conservation and environment protection. Dual cavity design, with functions of fully opening and fully closing. Slow shut causes no pressure uctuation, and the diaphragm with support is well protected. Antenna type of conduit, See No.4 and 5 conduit, connect with water knockout drum and water collector (supplying pipe and return pipe), can achieve accurate and reliable adjusting. Have internal orice, connect bottom cavity and outlet of the basic valve, make sure stability of reaction to keep stability of pressure after the valve, avoid any vibration and noise. Channel with straight-ow, slight friction loss, no eddy ow and turbulent ow, cut down the damage of cavitation. Long pitch orientation design for stem move, stable and no gap resistance. Balanced automatically, big gap design on connection of disc and stem, disc is free on the vertical at against stem, it can balance the tolerance from machining and sealing surface. Good connection without leakage. Achieve functions of both reducing dynamic pressure and reducing static pressure. Ductile iron castings with nodularity higher than 90%, foundry in house with advanced melting technology and strict quality control system, testing reports and testing bars can be supplied with order. Records and testing bars maintained for one year in the factory. Good corrosion resistance, with stainless steel, copper alloy, rubber made from DuPont and other rustresisting material, fusion bonded epoxy coating both for interior and exterior surface of the basic valve. All the characteristics in accordance with ANSI/AWWA C550 and other international specications like WRAS, NSF61.

4.Typical installation illustration

5.Notes for installation and debugging The valve has been finished initial debugging tests before delivery. Further debugging test is also suggested during using according to different set-conditions. Over review pressure meter of water knockout drum and water collector, adjust pilot valve (3) according to set-difference of pressure. Clockwise is for increasing the pressure difference and anti-clockwise is for reducing pressure difference when set adjusting screw on the top of pilot valve. When adjusting is done, fasten the lock nut. Then you'll got set-difference for the pressure no matter how the pressure of pipe system changes. Adjust needle valve (ball valve) can achieve different movement speed for the basic valve. Normally, it has been adjusted well before delivery. No further adjusting suggested if no special notice. 6.Common problems and proposed solutions
Common Problems Pressure difference is smaller than set-value and does not reach the set-difference. Pressure difference is bigger than set-value and does not reach the set-difference. Proposed Solutions a.Check if any sundries on the sealing surface of basic valve or pilot valve. b.Check if any damage on the sealing surface of basic valve or pilot valve. c.Check if needle valve (ball valve) (1) was closed or almost closed. If yes, please open it. a.Check if ball valve (6) at outlet was closed. If yes, please open it. b.Check if there's any block for pilot valve.

42

43

BS VALVES

SK790X Deluge Alarm Valve

1.Statement SK790X Deluge Alarm Valve is a diaphragm type of hydraulic control valve driven by the hydraulic pressure within the piping system, functioning as ow control and alarming device in the sprinkler and pre-action system, i.e. to start the sprinkler system for quenching of the re and send out re alarm through the re bell when there is re detected. 2.Operational principle SK790X Deluge Alarm Valve is equipped with solenoid, anti-reset controller, mini strainer, ball valve and pressure gauge, etc.. For deluge valve there is set condition and work condition. When the valve is under set condition, ball valve (3) is open, ball valve (7), solenoid (8) and remote ball valve (9) are closed, the anti-reset controller is connected, and pressure gauge (1) and pressure gauge (6) shows the same value. When ball valve (11) is open, pressure gauge (10) shows 0. When ball valve (12) and (14) are open, (13) & (15) closed, there is no hydraulic pressure for pressure switch (17) , and alarm (18) does not work. Under set condition, you can operate as following if you want to test the pressure switch alarm device (17) and water motor alarm (18): close ball valve (14) and open (15), and then close (15) and open (14) after testing. In case there is fire detected, the following 3 methods will set the deluge valve into work condition immediately, A: Opening solenoid valve (8) B: Opening ball valve (7) C: Opening remote ball valve (9). Any of the above 3 methods can get the pressure within the control room of the basic valve released rapidly to open the valve and set it into working condition. At this time the sealing ball of anti-reset controller makes controller in a shutdown state, water will pass through the main valve, ball valve (12), (4), pressure switch (17), re bell (18), the pressure switch bell sends out signal alarms. After re ghting, close ball valve (7), solenoid valve (8), remote valve (9), press the anti-reset controller handle till the pressure gauge (6) and pressure gauge (1) shows the same value. The deluge alarm valves returns to set condition. Ball valve (2), (5) & (11) are normally open unless need to change the pressure gauge. 3.Property and advantages Driven by pressure of pipe system, work automatically with energy of pipe system to achieve energy conservation and environment protection. Dual cavity design, with functions of fully opening and fully closing. Slow shut causes no pressure uctuation, and the diaphragm with support is well protected. Triple insurance, there're three opening types used for different situation of ring. Anyone can make the valve into working condition. Anti-reset controller, hydraulic pressure type, compact design, tight sealing, operating by hand to make sure all the parts including basic valve, ball valves and conduits are all in good condition after out-re. Channel with straight-ow, slight friction loss, no eddy ow and turbulent ow, cut down the damage of cavitation. Long pitch orientation design for stem move, stable and no gap resistance. Balanced automatically, big gap design on connection of disc and stem, disc is free on the vertical at against stem, it can balance the tolerance from machining and sealing surface. Good connection without leakage. Achieve functions of both reducing dynamic pressure and reducing static pressure. Ductile iron castings with nodularity higher than 90%, foundry in house with advanced melting technology and strict quality control system, testing reports and testing bars can be supplied with order. Records and testing bars maintained for one year in the factory. Good corrosion resistance, with stainless steel, copper alloy, rubber made from DuPont and other rustresisting material, fusion bonded epoxy coating both for interior and exterior surface of the basic valve. All the characteristics in accordance with ANSI/AWWA C550 and other international specications like WRAS, NSF61.

4.Typical installation illustration

5.Notes for installation and debugging Please check if pressure switch and alarm bell are in good condition before installation. Make sure water can not leak to system from water supplying system or there's equipment to discharge the leaked water. Please adjust all the ball valves to make sure the basic valve be in set condition. Make sure anti-reset controller is in good condition and seal well before installation. If there's water with pressure in front of the valve, please closed ball valve (7), (9) and electromagnetic valve when it's in empty state behind the basic valve, press the anti-reset controller, when up cavity of basic valve is full of water please check if there's any leakage behind the valve. If no leakage, it said anti-reset controller is in good condition. 6.Common problems and proposed solutions
Common Problems Press anti-reset controller after fire-out, there's still water coming out behind the valve. When open controlling valve (7), (8) and (9) no water comes out from the basic valve. Proposed Solutions a.Check if any sundries or damage on the sealing surface of basic valve or anti-reset controller. b.Check if any damage on diaphragm. c.Check if controlling valve (7), (8) and (9) were closed completely. Close them or replace with new ones. a.Check if controlling valve (7), (8) and (9) were opened. Close them or replace with new ones. b.Check if there's block on stem of basic valve, repair it.

44

45

BS VALVES

Ordering Guide of Hydraulic Control Valve


Piping system (two words) Size in mm (three digitals) Main property(three digitals) Other property(two digitals) Material of basic valve (one letter) Material of pilot valve (one letter) Pressure in bars (two digitals)
Water supply piping system: WW Drinking water piping system: WD Aggressive water piping system: WA Air conditioning water piping system: WC Heating piping system: WH 050 065 080 ... 700 Basic valve (Dual-chamber diaphragm) SK700X Basic valve (Single-chamber diaphragm) SK400X Basic valve (Piston type) SK800X Electromagnetic control valve SK710X Pressure reducing valve SK720X Pressure relief & sustaining valve SK730X Remote oat control valve SK750X Slow shut control valve (Pump control valve) SK760X Pressure differential by-pass balancing valve SK780X Deluge alarm valve SK790X No other special requirements Special closing and opening speed Non-retuning With high sensitive pilot valve With electromagnetic valve With electromagnetic valve and non-return With overpressure protection pilot valve With dual-disc Cracking pressure lower than 0.05MPa With throttle opening With indication of position With exhaust unit With Double liquid level control With ushing function in up chamber Other special requirement 00 03 06 09 12 15 18 21 24 27 30 33 36 39 99 Ductile Iron Q Carbon Steel C Stainless Steel P Al-bronze T Stainless steel P 10 16 25

Roll Groove Dimensions

Roll Grooving Machine


Pipe OD Basic mm/in 33.7 1.327 42.4 1.669 48.3 1.900 60.3 2.375 73.0 2.875 76.1 3.000 88.9 3.500 108.0 4.250 114.3 4.500 133.0 5.250 139.7 5.500 141.3 5.563 159.0 6.250 165.1 6.500 168.3 6.625 216.3 8.516 219.1 8.625 267.4 10.528 273.0 10.750 318.5 12.539 323.9 12.750 377.0 14.842 426.0 16.772 529.0 20.827 Tolerence mm/in +0.41 +0.016 +0.50 +0.020 +0.44 +0.017 +0.61 +0.024 +0.74 +0.029 +0.76 +0.030 +0.89 +0.035 +1.07 +0.042 +1.14 +0.045 +1.32 +0.052 +1.40 +0.055 +1.42 +0.056 +1.60 +0.063 +1.60 +0.063 +1.60 +0.063 +1.60 +0.063 +1.60 +0.063 +1.60 +0.063 +1.60 +0.063 +1.60 +0.063 +1.60 +0.063 +1.60 +0.063 +1.60 +0.063 +1.60 +0.063 -0.68 -0.026 -0.60 -0.023 -0.52 -0.020 -0.61 -0.024 -0.74 -0.029 -0.76 -0.030 -0.79 -0.031 -0.79 -0.031 -0.79 -0.031 -0.79 -0.031 -0.79 -0.031 -0.79 -0.031 -0.79 -0.031 -0.79 -0.031 -0.79 -0.031 -0.79 -0.031 -0.79 -0.031 -0.79 -0.031 -0.79 -0.031 -0.79 -0.031 -0.79 -0.031 -0.79 -0.031 -0.79 -0.031 -0.79 -0.031 Groove Dia C Basic mm/in 30.23 1.190 38.99 1.535 45.09 1.779 57.15 2.250 69.09 2.720 72.26 2.845 84.94 3.344 103.73 4.084 110.08 4.334 129.13 5.084 135.48 5.334 137.03 5.395 154.50 6.083 160.8 6.330 163.96 6.455 211.60 8.331 214.40 8.441 262.60 10.339 268.28 10.562 312.90 12.319 318.29 12.531 371.44 14.623 420.46 16.553 523.46 20.608 Tolerence mm/in -0.38 -0.015 -0.38 -0.015 -0.38 -0.015 -0.38 -0.015 -0.46 -0.018 -0.46 -0.018 -0.46 -0.018 -0.51 -0.020 -0.51 -0.020 -0.51 -0.020 -0.51 -0.020 -0.56 -0.022 -0.56 -0.022 -0.56 -0.022 -0.56 -0.022 -0.64 -0.025 -0.64 -0.025 -0.69 -0.027 -0.69 -0.027 -0.76 -0.030 -0.76 -0.030 -0.76 -0.030 -0.76 -0.030 -0.76 -0.030

Nominal Size mm/in 25 1 32 1 40 1 50 2 65 2 65 2 80 3 100 4 100 4 125 5 125 5 125 5 150 6 150 6

Gasket seat A 0.76/0.03 mm/in 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 19.05 0.750 19.05 0.750 19.05 0.750 19.05 0.750 19.05 0.750 19.05 0.750 23.83 0.938 23.83 0.938 25.40 1.000

Groove Width B 0.76/0.03 mm/in 7.14 0.281 7.14 0.281 7.14 0.281 8.74 0.344 8.74 0.344 8.74 0.344 8.74 0.344 8.74 0.344 8.74 0.344 8.74 0.344 8.74 0.344 8.74 0.344 8.74 0.344 8.74 0.344 8.74 0.344 11.91 0.469 11.91 0.469 11.91 0.469 11.91 0.469 11.91 0.469 11.91 0.469 11.91 0.469 11.91 0.469 11.91 0.469

Groove Depth MaxAllow Flare D(ref) Dia F mm/in mm/in 1.60 0.063 1.60 0.063 1.60 0.063 1.60 0.063 1.98 0.078 1.99 0.078 1.98 0.078 2.11 0.083 2.11 0.083 2.11 0.083 2.11 0.083 2.13 0.084 2.16 0.085 2.16 0.085 2.16 0.085 2.35 0.093 2.34 0.092 2.40 0.095 2.39 0.094 2.77 0.109 2.77 0.109 2.77 0.109 2.77 0.109 2.77 0.109 34.5 1.358 43.3 1.705 49.4 1.945 62.2 2.449 75.2 2.961 77.7 3.059 90.6 3.567 109.7 4.319 116.2 4.575 134.9 5.311 141.7 5.579 143.5 5.650 161.0 6.339 167.1 6.579 170.7 6.720 219.8 8.653 221.5 8.720 270.9 10.665 275.4 10.842 322.0 12.677 326.2 12.842 379.5 14.941 428.5 16.870 533.0 20.984

Min. Allow wall thickness T mm/in 1.8 0.071 1.8 0.071 1.8 0.071 1.8 0.071 2.3 0.091 2.3 0.091 2.3 0.091 2.3 0.091 2.3 0.091 2.9 0.114 2.9 0.114 2.9 0.114 2.9 0.114 2.9 0.114 2.9 0.114 2.9 0.114 2.9 0.114 3.6 0.142 3.6 0.142 4.0 0.158 4.0 0.158 4.5 0.177 4.5 0.177 5.0 0.197

Examples:

DN80, PN16, Dual-chamber diaphragm type remote oat control valve for water supply piping system, with electromagnetic valve controlling, Ductile iron basic valve body, brass pilot valve: WW-080-SK750X-12-QT-16 DN200, PN10, Dual-Chamber diaphragm type slow control valve for drinking water piping system, specially used for the pool water (under 0.05MPa), Stainless steel basic valve body, Stainless steel pilot valve: WD-200-SK760X-24-PP-10

Notes for Installation of Hydraulic Control Valve


Check the uniformity of name plate, quality guarantee card and marking on valve products. Clean the pipes and make sure no rocks, welding slags and other sundries. Horizontal installation is the best choice, and other installing direction can also be chosen and work properly. Strainer is suggested to be installed before the basic valve, besides, maintenance gate valves were also suggested to be installed before and after the basic valve. Make sure the direction of ow is same as arrow on basic valve. The protection plugs on the both ends are suggested to be removed just before installation to avoid sundries coming inside. Check the connection of conduits to make sure no broken, damage and loosing after installation. Check the repairing ball valve to make sure they're open after installation.

For English Speaking Service


R&D Center: Chief Engineer: Ms. Xiaobei Huang Tel: 0086-531-87746667 E-mail: huangxiaobei@meide-casting.com Sales Department: Exporting Sales Department: Ms. Zhaoxia Su Tel: 0086-531-87879384 Fax: 0086-531-87879387 E-mail: suzhaoxia@meide-casting.com Exporting Sales Department: Ms. Sunny Guo Tel: 0086-531-87885036 Fax: 0086-531-87879387 E-mail: guoxiaohua@meide-casting.com

150 6 200A 8 200 8 250A 10 250 10 300A 12 300 12 350 14 400 16 500 20

46

47

BS VALVES

Flange Dimensions

Flange Dimensions

Dimensions of PN10 anges (BS EN 1092-2:1997)


(mm) Mating dimensions DN mm Outside diameter Diameter of bolt Diameter of bolt of ange circle hole D K L 90 95 105 115 140 150 165 185 200 220 250 285 340 395 445 505 565 615 670 780 895 1015 1115 1230 1455 1675 1915 2115 2325 60 65 75 85 100 110 125 145 160 180 210 240 295 350 400 460 515 565 620 725 840 950 1050 1160 1380 1590 1820 2020 2230 14 14 14 14 19 19 19 19 19 19 19 23 23 23 23 23 28 28 28 31 31 34 34 37 41 44 50 50 50 Bolts Number n 4 4 4 4 4 4 4 4 8 8 8 8 8 12 12 16 16 20 20 20 24 24 28 28 32 36 40 44 48 Nominal size M12 M12 M12 M12 M16 M16 M16 M16 M16 M16 M16 M20 M20 M20 M20 M20 M24 M24 M24 M27 M27 M30 M30 M33 M36 M39 M45 M45 M45 Grey Iron 14 14 16 16 18 18 20 20 22 24 26 26 26 28 28 30 32 32 34 36 40 44 46 50 56 62 68 70 74 Flange thickness C Ductile Iron 14 14 16 16 18 19 19 19 19 19 19 19 20 22 24.5 24.5 24.5 25.5 26.5 30 32.5 35 37.5 40 45 46 49 52 55 Malleable Iron 14 14 16 16 18 18 20 20 20 22 22 24 24 26 26 -

Dimens ions of P N10 f langes ( B S E N 1092- 2: 1997)


(mm) Mating dimensions DN mm Outside diameter Diameter of bolt Diameter of bolt of ange circle hole D K L 90 95 105 115 140 150 165 185 200 220 250 285 340 405 460 520 580 640 715 840 910 1025 1125 1255 1485 1685 1930 2130 2345 60 65 75 85 100 110 125 145 160 180 210 240 295 355 410 470 525 585 650 770 840 950 1050 1170 1390 1590 1820 2020 2230 14 14 14 14 19 19 19 19 19 19 19 23 23 28 28 28 31 31 34 37 37 41 41 44 50 50 57 57 62 Bolts Number n 4 4 4 4 4 4 4 4 8 8 8 8 12 12 12 16 16 20 20 20 24 24 28 28 32 36 40 44 48 Nominal size M12 M12 M12 M12 M16 M16 M16 M16 M16 M16 M16 M20 M20 M24 M24 M24 M27 M27 M30 M33 M33 M36 M36 M39 M45 M45 M52 M52 M56 Grey Iron 14 14 16 16 18 18 20 20 22 24 26 26 30 32 32 36 38 40 42 48 54 58 62 66 Flange thickness C Ductile Iron 14 14 16 16 18 19 19 19 19 19 19 19 20 22 24.5 26.5 28 30 31.5 36 39.5 43 46.5 50 57 60 65 70 75 Malleable Iron 14 14 16 16 18 18 20 20 20 22 22 24 24 26 28 -

10 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700 800 900 1000 1200 1400 1600 1800 2000

10 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700 800 900 1000 1200 1400 1600 1800 2000

48

49

BS VALVES

Note:

50

51

Anda mungkin juga menyukai