T Series
Gorman-Rupp T Series pumps are designed for economical, trouble-free operation in handling solids-laden liquids and slurries. Pumps feature a large volute design which allows them to reprime automatically in a completely open system without the need for suction or discharge check valves. And they can do it with the pump casing only partially filled with liquid and a completely dry suction line.
Sizes: 3", 4", 6", 8", 10" (75 mm, 100 mm, 150 mm, 200 mm, 250 mm) Materials of Construction: Cast Iron, 316 Stainless Steel, CD4MCu, G-R Hard Iron Max. Capacity: 3400 gpm (214 lps) Max. Head: 130 ft. (39.6 m) Max. Solids: 3" (76 mm)
Discharge Outlet
Features
Solids Handling Impeller Two-vane, semi-open solids handling impeller handles up to 3" (76 mm) diameter solids, depending on pump model. Pump out vanes on impeller shroud reduce foreign material buildup behind impeller and reduce pressure on seal and bearings.
Exclusive Gorman-Rupp Cartridge Seal Exclusive double-floating, self-aligning, oil lubricated mechanical cartridge seal with stationary and rotating face of silicon carbide is specifically designed for abrasive industrial service. Seal is available on 3", 4" and 6" (75 mm, 100 mm and 150 mm) pump models. Metal bellow seals are also available.
Removable Coverplate and Wearplate Removable coverplate and wearplate provides quick and easy access to pump interior without disconnecting piping. Clogs can be removed and pump returned to service in minutes. Impeller, seal, wearplate and flap valve can also be accessed through coverplate opening for inspection or service.
Removable Rotating Assembly Inspection of pump shaft or bearings is easily accomplished without disturbing pump casing or piping by removing rotating assembly. On most models, simply remove four bolts from the back of the pump and the assembly slides out.
Optional Equipment: Air release valve Suction & discharge flanged spools Casing heaters High temperature shut down
Note: In addition to the fourteen basic units mentioned on these pages, pumps may on special order be engine powered and mounted on wheels for portability and stand-by use during power failure.
INCH
(75 mm)
Performance Curve
Performance as shown has been obtained by pumping 70 clear water. Altitude was corrected to sea level. The pipe and fittings were common in size to pump suction and discharge. Suction pipe incorporated 5' horizontal run from pump to vertical drop into wet well. Individual curves pertaining to the performance of each pump at constant speed, with variable impeller diameter with variable speed for each impeller diameter, are available on request to factory.
REPRIMING LIFTS
RPM 650 750 850 950 1050 1150 1250 1350 18 8 10 13 19 5 6 16 FEET 5,8 METERS 1,5 1,8 2,4 3,0 4,0 4,9 5,5
Figure NPSH reguired prior to using above table. DO NOT use as available suction lift.
1450-1550 21 6,4
1650-1750 22 6,7
1850-2150 25 7,6
PERFORMANCE CURVE
CURVE MODEL
T3A-B-4 T3A-B
IMP.DIA. 8-3/4" (222mm)
215 0R
205 0
PM
30 35 40
OPERA RANGTING E 45 48
1.0
RPM
VARIOUS
50 50 20 BH P 48
15[ 11,
,5]
1750
1650
70 1550 1450 60 1350 50 1 250 1 1 50 40 1050 30 950 850 20 750 650 10 0 125 100 150 175 0 25 50 75 200 225 250 275 300
[14
,9
KW
2]
NPSH FT 30 M
10[7
45
7.5[
5[3,7 ]
5,6]
1[,75]
325 350
2[1,5]
375 400
3[2,2
425
]
450 475 500 32
10 8 20 6 4 10 2 0 0
U.S.GALLONS PER MINUTE LITRES PER SECOND CUBIC METRES PER HOUR
10
12
14
16
18
20
22
24
26
28
30
10
20
30
40
50
60
70
80
90
100
4" T Series pump transferring wastewater to a holding tank at a starch plant in Denmark.
110
T-2-98-R
Performance Curve
TOTAL HEAD M 44 60 40 36 32 28 24 32 20 16 12 8 4 0 28 24 20 16 12 8 4 0 56 52 48 44 40 36 140 130 120
195
185
REPRIMING LIFTS
4
CURVE MODEL SP.GR.
INCH
(100 mm)
T4A-B-4 T4A-B
PSI
FT
650 5 1,5
750 8 2,4
850 16 4,9
950 19 5,8
PERFORMANCE CURVE
Figure NPSH required prior to using above table. DO NOT use as available Suction Lifts.
0 RP
35
40 45
1.0
RPM
VARIOUS
110 17 50 100 1650 90 1550 80 1450 70 1350 60 1250 50 1150 1050 40 950 30 850 750 20 6 50 10 0 0
NPSH@1950RPM
1[,75]
50 55 55
25
20[
15[
14,
2]
9]
NPSH FT M
11,
10[
7,5]
2[1,5
3[2,2
5[3,7
7.5[
5,6]
10
15
25
35
45
55
75
85
20
30
40
50
65
70
80
90
95
X 10
12
16
24
28
32
44
48
36
52
56
20
40
11
12
13
14
15
17
18
16
19
21
60
64 23
T-2-98-R
10
20
22
100
60
10 8 20 6 4 10 2 0 0 30
REPRIMING LIFTS
850 10 3,0 1150-1450 20 6,1 1750-2150 22 6,7
PERFORMANCE CURVE
CURVE MODEL
Note: Select performance within operating range of curve
T4B-B-6 T4B-B
65 60 55 50 45
Figure NPSH reguired prior to using above table. DO NOT use as available suction lift.
1.0
RPM
VARIOUS
2150 RPM
30
OPERATING RANGE
40 50 55 60 62 63 63 62 60
2050
40 35 30 25 20 15 10 10 5 0 0
LITRES
1950
1850
1750
50 40
40 [29 B ,8 KHP W]
NPSH FT M
1650
80 30 60 20 40 20 0
600
1[,75]
35 40
2[1,5]
45
3[2,2]
50 55
5 [3,7]
60
[2230 ,4] 2 [18 5 ,6] [1420 ,9] 15 [1 1,2] 10 [7 ,5] 7.5 [5,6 ]
30 20 10 0
10 8 6 4 2 0
65
70 44 16 46
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
10
11
12
13
14
15
42
17
75
T-2-98-R
6
M 44 60 40 36 56 52 48 32 28 24 32 20 16 12 8 4 0 28 24 20 16 12 8 4 0 44 40 36 PSI
INCH
(150 mm)
FT 140 130 120
Performance Curve
PERFORMANCE CURVE
CURVE MODEL
Note: Select performance within operating range of curve.
TOTAL HEAD
REPRIMING LIFTS
650 750 850 950 1050 1150-1250 1350 1450 1550 RPM 22 23 25 8 9 12 14 18 21 FEET 6,7 7,0 7,6 METERS 2,4 2,7 3,7 4,3 5,5 6,4
Figure NPSH reguired prior to using above table. DO NOT use as available suction lift.
T6A-B-4 T6A-B
1.0
1550
RPM
VARIOUS
RPM
40 50 55
OP ER RA ATING NG E
Consult factory on operating conditions above 1350 rpm when TDSL exceeds 20 ft.
1350
60
1150
80 1250 70 60
60 55 50
NPSH
40
1050
30
FT 30
,8K
650
2[1,5]
8 9
5[3,
10
BH P[ 29 W]
7]
11 12 13 14 15 17 18 16 19 20 13 46 44
10 8 20 6 4 10 2 0 0
X 100
11
X 10
12
14
10
16
18
10
12
22
24
28
32
34
38
26
20
30
36
REPRIMING LIFTS
RPM FEET METERS 1150 15 4,6 1450 20 6,1 1750 24 7,3
PERFORMANCE CURVE
CURVE MODEL
Note: Select performance within operating range of curve.
40
42
T-2-98-R
T6B-B-1 T6B-B
Figure NPSH reguired prior to using above table. DO NOT use as available suction lift.
1750 RPM
1650
1550
45
50
55
1.0
RPM
VARIOUS
60 55 62 50
50
1450
1350
1250
1150
64
NPSH FT 30
]
BH
1050
950 850
7.5
40
30
5 [3
,7]
10
15 [1 10 1, [ [5,6 7,5] 2] ]
11 12 13
20
25
[2 9, 8]
P [3 3 7, KW
[1 8,6] 4,9 ]
[1
10 8 20 6 4 10 2 0 0
19 12 20 13 46
T-2-98-R
[2 2, 4]
U.S.GALLONS PER MINUTE LITRES PER SECOND CUBIC METRES PER HOUR
14
15
16
17 38 11
X 10
10
12
14
16
18
20
22
24
26
28
30
32
34
36
10
40
18
42
X 10
44
Performance Curve
INCH
(200 mm)
MODEL T8A60-B MODEL T8A61-B MODEL T8A65-B
REPRIMING LIFTS
850 15 4,6 950 17 5,2 1050 1150 1250 1350 23 22 21 20 7,0 6,7 6,4 6,1
PERFORMANCE CURVE
CURVE MODEL
Note:
Select performance within operating range of curve.
T8A-B-3 T8A-B
Figure NPSH reguired prior to using above table. DO NOT use as available suction lift.
0RP
1.0
M 30
RPM
VARIOUS
40 50 55 60 63
OP ER RA ATIN NG G E
Consult factory on operating conditions above 1200 rpm when TDSL exceeds 20 ft.
115
105
63 60 55 50 65 67
30
2,2 [5 P BH 70 ,7] ] 4 3 7, 60 [4
950
50 850 40 750 30 20 10 0 12 14 10 16 18 2 4 0 6 8 24
NPSH FT 30
]
50
650
40
[22
[2
20
9,8
,4]
10 8 6 20 4 10 2 0 0
36 38 24 22 40 9 26
T-2-98-R
[3
KW
28
32 7 20
26
X 100
12
14
X 10
10
16
18
30
34
6" T Series pumping corrosive petroleum wastes at a waste recovery plant in the Netherlands.
6" T Series pumps handling solids-ladden wastewater at an automotive plant in Michigan, USA.
8" T Series pump handling white water at a corrugated plant in Ohio, USA.
10
1 0
INCH
(250 mm)
Performance Curve
REPRIMING LIFTS
850 14 4,3 950 17 5,2 1050-1150 1250 1350-1450 18 19 22 5,5 5,8 6,7
PERFORMANCE CURVE
CURVE MODEL
Note: Select performance within operating range of curve.
T10A-B-4 T10A-B
65 60 55 50 45
Figure NPSH reguired prior to using above table. DO NOT use as available suction lift.
1.0
RPM
VARIOUS
1450
1350
1250
RPM
50
40 35 30 25 20 15 10 5 0 0
U.S. GALLONS PER MINUTE
60 70
50
75 79 79 75
1 [7 00 4,6 BH 9 P [6 0 KW] 7,1 7 ] [520 ,2] 50 [37 ,3]
]
350
1150
70
1050
950
NPSH FT M
850
30 20 10 0
10 8 6 4 2 0
750 40 650
20
10 [7,5]
225 100 250
20 [14, 9]
275 300
30 [22 ,4
11
12
13
14
15
17
18
21
325 20
10
16
19
22 80
X 10
10
15
25
35
45
55
75
23 85
T-2-98-R
60
20
30
40
50
65
10" T Series pump handling abrasive, solids-ladden run-off at a steel mill in Pennsylvania, USA.
70
11
Drive Variations
Gorman-Rupp T Series pumps are available as basic units for connection to customers power or may be flex-coupled or V-belt driven by an electric motor. When space is critical, flex-coupling often solves the tight-fit problem. V-belt drive offers the advantage of flexibility in speed selection and usually provides maximum operating speed for required head and capacity without trimming impeller. Belt and sheave configurations are constructed to industry standards and are universally available. T Series pumps may also be powered by gasoline or diesel engines.
Basic
V-Belt
Flexible
Engine Driven
12
Air-Driven Diaphragm Heavy Sludges and Slurries Air-driven diaphragm pumps have an extra-thick pump casing for handling heavy sludges and solids. Pumps will handle high solids content up to 70%. Pumps are available in 1-1/2" to 4" (40 mm to 100 mm) sizes, capacities to 170 gpm (11 lps), heads to 200' (61 m). They will handle up to 3" (76 mm) solids.
10 Series-Solids and Corrosive Liquids 10 Series self-priming pumps have only two moving parts impeller and shaft, so maintenance problems are minimal. Pumps are available in 1-1/2" to 6" (38 mm to 150 mm) sizes. Capacities to 1300 gpm (82 lps), heads to 100' (30.5m). Pumps handle up to 2-1/2" (63.5 mm) spherical solids depending on pump model. Multiple seal options available.
U Series-High Efficiency Solids and Corrosive Liquids U Series self-priming pumps are among the most efficient solids handling, selfpriming pumps available (up to 75 %). Open, multi-vane impeller will handle solids up to 1-1/4' (31.8 mm) in diameter. Pumps are available in 3", 4" and 6" (75 mm, 100 mm, and 150 mm) sizes, capacities to 1500 gpm (94.6 lps), heads to 210' (64 m).
80 Series-Limited Solids and Corrosive Liquids 80 Series self-priming pumps are designed for high-efficiency, non-stop workloads. Straight-in suction design allows them to operate on higher suction levels than standard self-priming centrifugals. Pumps are available in 1-1/4" to 8" (30 mm to 200 mm) sizes. Capacities to 2100 gpm (132.5 lps), heads to 180' (54.9 m). Multiple seal options available.
90 Series-Corrosive Liquids and Limited Solids 90 Series self-priming pumps are specifically designed for applications where limited access is critical. All wearing parts can be quickly replaced using common hand tools. Pumps are available in 2" and 3" (50 mm and 75 mm) sizes. Capacities to 320 gpm (53.4 lps), heads to 180' (54.9 m). Multiple seal options available.
0 Series-Clear Liquids 0 Series self-priming pumps feature straight-in suction which eliminates entrance restrictions and provides better suction performance when handling solvents, petroleum products and similar liquids. Available in 2" to 6" (50 mm to 150 mm) sizes. Capacities to 1350 gpm (85.2 lps), heads to 390' (118.9 m).
The Gorman-Rupp Company 305 Bowman Street, P.O. Box 1217 Mansfield, Ohio 44901-1217 419-755-1011 Fax 419-755-1251
The Gorman-Rupp International Company P.O. Box 1217 Mansfield, Ohio 44901-1217 419-755-1011 Fax 419-755-1266 www.gormanrupp.com
Gorman-Rupp of Canada, Ltd. 70 Burwell Road St. Thomas, Ontario N5P 3R7 519-631- 2870 Fax 519 - 631- 4624
Printed in U.S.A.