0 penilaian0% menganggap dokumen ini bermanfaat (0 suara)
146 tayangan4 halaman
ASTM A192 / ASME SA192 belongs to the carbon seamless tubes, which is specially designed for high, middle, low pressure purpose in seamless carbon steel boilers and as super heater tubes. The steel shall conform to the required chemical composition for carbon, manganese, phosphorus, sulfur, and silicon. The tubes shall have a hardness number not exceeding a specific value.
ASTM A192 / ASME SA192 belongs to the carbon seamless tubes, which is specially designed for high, middle, low pressure purpose in seamless carbon steel boilers and as super heater tubes. The steel shall conform to the required chemical composition for carbon, manganese, phosphorus, sulfur, and silicon. The tubes shall have a hardness number not exceeding a specific value.
ASTM A192 / ASME SA192 belongs to the carbon seamless tubes, which is specially designed for high, middle, low pressure purpose in seamless carbon steel boilers and as super heater tubes. The steel shall conform to the required chemical composition for carbon, manganese, phosphorus, sulfur, and silicon. The tubes shall have a hardness number not exceeding a specific value.
Http://www.sunnysteel.com E-mail: sales@sunnysteel.com Page:1 of ASTM A192, ASME SA192.doc
ASTM A192/ ASME SA192 ASTM A192 belongs to the carbon seamless tubes, which is specially designed for high, middle, low pressure purpose in seamless carbon steel boilers and as super heater tubes.
ASTM A192 Specification for Seamless Carbon Steel Boiler Tubes for High-Pressure Service ASTM A192 American Society for Testing Materials standard ASME SA192 - American Society of Mechanical Engineers standards This guide covers standard specifications for minimum-wall-thickness, seamless carbon steel boiler and superheater tubes for high-pressure service. The steel shall conform to the required chemical composition for carbon, manganese, phosphorus, sulfur, and silicon. The tubes shall have a hardness number not exceeding a specific value. The following mechanical tests shall be conducted, namely: flattening test; flaring test; hardness test; and hydrostatic test. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
Sunny Steel Enterprise Ltd. Collect Steel pipe and fitting Resources
Http://www.sunnysteel.com E-mail: sales@sunnysteel.com Page:2 of ASTM A192, ASME SA192.doc
Chemical Compositions (%) of ASTM A192 C Si Mn P S Cr Mo Cu Ni V 0.06-0.18 0.25 0.27-0.63 0.035 0.035 / / / / / Mechanical Properties of ASTM A192 Yield Strength (Mpa) Tensile Strength (Mpa) Elongation (%) 180 325 35 Scope This specification covers minimum-wall-thickness, seamless carbon steel boiler and superheater tubes for high-pressure service. The tubing sizes and thicknesses usually furnished to this specification are in. to 7 in. [12.7 to 177.8 mm] outside diameter and 0.085 to 1.000 in. [2.2 to 25.4 mm], inclusive, in minimum wall thickness. Tubing having other dimensions may be furnished, provided such tubes comply with all other requirements of this specification. Mechanical property requirements do not apply to tubing smaller than 1/8 in. [3.2 mm] inside diameter or 0.015 in. [0.4 mm] thickness. The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the M designation of this specification is specified in the order. Note: Mill test certificates will be issued according to EN10204.3 All tubes shall be supplied as per applicable ASTM Specification. The tubes Shall be Seamless and the testing shall be as per A 450 / A450M.
Application: apply to the heat exchangers, condensers and heat transfer equipment and similar pipe.
Sunny Steel Enterprise Ltd. Collect Steel pipe and fitting Resources
Http://www.sunnysteel.com E-mail: sales@sunnysteel.com Page:3 of ASTM A192, ASME SA192.doc
Marking: Pipes are supplied with marking according to standard and customer request. Marking is paint on the ends of pipes. The same data, as well as additional information per customers request, is indicated on the bundles tags. Delivery: Pipes are supplied in hexagonal bundles or round bundles tied with steel strip. Weight of bundle up to 5000 kg upon request of customer. Each bundle is furnished with three tags.
Sunny Steel Enterprise Ltd. Collect Steel pipe and fitting Resources
Http://www.sunnysteel.com E-mail: sales@sunnysteel.com Page:4 of ASTM A192, ASME SA192.doc
Read more information of seamless steel pipes Why seamless steel pipe? Some benefits of Seamless Steel Pipe The usage of Carbon steel pipe How to produce the steel pipes? Cold-Drawn Seamless Pipe Specifications The Manufacturing Process of steel pipe Steel Pipe and Its Many Uses History of Steel Pipe, Steel pipes Seamless Tube and Pipe Manufacturing Processes ASTM A179/ ASME SA179 Standard Specification Types, Lengths and Ends of Steel pipes Comparing American and British Piping Standards Seamless tube, Seamless tubing Description and Details of steel Pipes Seamless steel pipes for low and medium pressure service
Get in Touch If you are interested in our products or cooperating with us, even having a comment or a suggestion please contact us now, for more detailed information. Tel.: +8621 3378 0199 | E-mail:sales@sunnysteel.com