CELL_BAR_QUALIFY Priority of cell for cell selection
CELL_BAR_ACCESS Allows or disallows MS to camp on cell in idle mode MAX_RETRAN is the maximum number of retransmissions a MS may perform on the RACH MS_TXPWR_MAX_CCH MS shall use the power level defined by the MS_TXPWR_MAX_CCH parameter broadcast on the BCCH IMSI Attach Detach (ATT) This flag indicates to the MS whether IMSI Attach/detach procedure (when the MS is turned on/off respectively) is allowed in the cell. T3212 (Periodic Location Update) This timer indicates to the MS the delay between two consecutive Periodic Location Update procedures. Cell-Reselect-Hysteresis in the case of the new cell being in a different location area in which case the C2 value for the new cell shall exceed the C2 value of the serving cell by at least CELL_RESELECT_HYSTERESIS dB as defined by the BCCH data from the current serving cell, for a period of 5 seconds CELL_RESELECT_OFFSET Applies an offset to the C2 reselection criterion TEMPORARY_OFFSET Applies a negative offset to C2 for the duration of PEN/ALTY_TIME. PEN/ALTY_TIME Gives the duration for which the temporary offset is applied RXLEV_ACCESS_MIN is used to indicate the minimum receive level at the MS required for access to the system. This parameter is used in order to evaluate the path loss criterion parameter (C1) of a cell NCC_PERMITTED The purpose of the NCC Permitted information element is to provide a definition of the allowed NCCs on the BCCH carriers to be reported in the MEASUREMENT REPORT message by the MSs in the cell. Hopping Type Type of hopping (BBH, SFH) HSN Hopping Sequence Number Mobile Allocation List List containing ARFCNs on which the configured channel can hop TSC Training Sequence Code (for channel equilization & error detection) MAIO Mobile Allocation Index Offset (Determines from where in the frequency hopping lict shall the channel start hopping) BS_AG_BLKS_RES specifies the number of TDMA frames reserved for the Access Grant channel during a period of 51 TDMA frames (a multiframe). BS_PA_MFRMS denotes the number of multiframes (51 frames) between two transmissions of the same paging message to mobiles of the same paging group TX_INTEGER is used to represent the maximum number of RACH slots a MS must wait, after an unsuccessful random access attempt, before a new random access. The MS draws a random number between 0 and the value of this parameter, in order to decide when to start the new access. Hence this parameter allows the access retransmissions be spread over a fixed number of RACH slots. RACH filter based on TA Threshold above which TA value RACHs are not serviced by the BSS Wait Indication provide the time the MS shall wait before attempting another channel request. L_RXLEV_DL_PC Lower RXLEV threshold for DL PC U_RXLEV_DL_PC Upper RXLEV threshold for DL PC L_RXLEV_UL_PC Lower RXLEV threshold for UL PC U_RXLEV_UL_PC Upper RXLEV threshold for UL PC L_RXQUAL_DL_PC Lower RXQUAL threshold for DL PC U_RXQUAL_DL_PC Upper RXQUAL threshold for DL PC L_RXQUAL_UL_P Lower RXQUAL threshold for UL PC U_RXQUAL_UL_PC Upper RXQUAL threshold for UL PC EN_RADIOLINK_RECOVERY_PROC eN/Ables/disables the Radio Link Recovery procedure i.e. MS and BS are ordered to be on full power RADIO_LINK_TIMEOUT(BS) Counter threshold to detect a radio link failure on the uplink path (running in BTS) RADIO_LINK_TIMEOUT(MS) Initial value of MS counter for radio link supervision. Counter threshold to detect a radio link failure on the downlink path (running in MS) RADIO_LINK_TIMEOUT_AMR(MS) Initial value of MS counter for radio link supervision for AMR calls. Counter threshold to detect a radio link failure on the downlink path (running in MS) RADIO_LINK_TIMEOUT_AMR(BS) Counter threshold to detect a radio link failure on the uplink path for AMR calls (running in BTS) EN/ABLE_DL_DTX_AMR_FR EN/Ables or disables downlink DTX for AMR FR calls EN/ABLE_DL_DTX_AMR_HR EN/Ables or disables downlink DTX for AMR HR calls EN/ABLE_DL_DTX_HR EN/Ables or disables downlink DTX for HR calls EN/ABLE_UL_DTX EN/Ables or disables uplink DTX for non-AMR calls EN/ABLE_UL_DTX_AMR EN/Ables or disables uplink DTX for AMR calls PING_PONG_MARGIN Hysterisis applied to prevent ping pong handovers (back & fro handovers between same 2 cells) EN_INTRA_HO EN/Ables or disables intracell handovers EN_PBGT_HO EN/Ables or disables power budget handovers A_LEV_HO Averaging window of MRs for RXLEV measurements HOM Handover margin to compare PBGT of source and candidate neighbour cell EN_RXQUAL_HO EN/Ables or disables quality handovers A_QUAL_HO Averaging window of MRs for RXQUAL measurments L_RXQUAL_UL_H Threshold for UL quality to trigger quality handover L_RXQUAL_DL_H Threshold for DL quality to trigger quality handover QLIMAMRFR/HR Threshold (offset added to threshold) to trigger quality handover on a hopping/AMR/HR channel HOM_QUAL Handover margin to compare PBGT of source and candidate neighbour cell for quality handovers EN_DIRECTED_RETRY EN/Ables or disable DR in BSC EN_DIRECTED_RETRY EN/Ables or disable DR in Cell EN/ABLE_DL_DTX_FR EN/Ables or disables downlink DTX for FR and EFR calls EN_DIRECTED_RETRY Makes a neighbour available or uN/Available as a candidate to take DR Hos EN_DIRECTED_RETRY Allows or disallows handovers to trigger during SD to TCH assignment phase EN/Able congestion handover EN/Ables or Disables congestion relief procedure Congestion handover threshold Threshold above which if the cell's resources are used will trigger congestion relief procedure on next resource request OPTILAYER Set the preferred band of the system (network) Power level for handover in the inner zone Minimum RxLev DL from neighbour cell (lower layer or preferred band)for umbrella to lower layer handover or from classical band to preferred band handover. Upper congestion threshold to reconfigure MS on FR to HR channel, through intracell HO Upper congestion threshold to give MS an HR channel POWER_SETTING To set the desired BTS power IMMASSEN Immediate assignment on TCH is allowed SDDYN Dynamic SD allocation is allowed DYNOPENTRXPOWER BTS Power saving during non Peak hour ECSC Early Class mark sending control allowed FMSMAXOPCC MS Maximum Transmit power INTERFTHRES Samples of Interference band OPTILEVTHRES HR-FR Huawei Ericsson CBQ (Cell) CBQ CBA (Cell) CB MSMAXRETRAN MAXRET MS_TXPWR_MAX_CCH (Cell) MSTXPWR ATT (Cell) ATT T3212(Period of Periodic Location Update) (Cell) T3212 (Time between periodic update of MS) CRH (Cell) CRH CRO (Cell) CRO TO (Cell) TO PT (Cell) PT RXLEV_ACCESS_MIN (Cell) ACCMIN NCC_PERMITTED (Cell) NCCPERM FH Mode (Cell) FHOP (Cell) HSN (Cell) HSN (Cell) MA (Cell) MAL (Cell) TSC (Cell) TSC (Cell) MAIO (Cell) MAIO BS_AG_BLKS_RES (Cell) AGBLK (Cell) BS-PA-MFRAMS (Cell) MFRMS (Cell) TX-Integer (Cell) TX (Cell) MAX TA (Cell) MAXTA (Cell) T3122 (Cell) T3122 DL RX_LEV Lower Threshold DL RX_LEV Upper Threshold UL RX_LEV Lower Threshold UL RX_LEV Upper Threshold DL Qual. Lower Threshold DL Qual. Upper Threshold UL Qual. Lower Threshold UL Qual. Upper Threshold RADIO LINK TIMEOUT RLINKT (Cell) AFR Radio Link Timeout(SACCH period (480ms)) AHR Radio Link Timeout(SACCH period (480ms)) RLINKTAFR , RLINKTAHR (Cell) AFR SACCH Multi-Frames(SACCH period (480ms)) AHR SACCH Multi-Frames(SACCH period (480ms)) RLINKUPAFR , RLINKUPAHR (Cell) Inter-cell HO Hysteresis HYSTSEP Intracell HO Allowed IHO (Cell) PBGT HO Allowed CAND Filter Length for TCH Level SSEVALSD PBGT HO Threshold OFFSETP BQ HO Allowed AW Filter Length for TCH Qual QEVALSD UL Qual. Threshold QLIMUL DL Qual. Threshold QLIMDL DLQuaLimitAMRFR ULQuaLimitAMRFR DLQuaLimitAMRHR ULQuaLimitAMRHR QLIMULAFR QLIMDLAFR BQ HO Margin BQOFFSET DL DTX UL DTX DTXD DTXU Direct Retry AW SSDESDL SSDESUL QDESDL QDESUL RLINKUP Load HO Allowed HOCLSACC Load HO Threshold CLSLEVEL , CLSACC Assign Optimum Layer\System Optimization Layer Setting TCH Traffic Busy Threshold(%) AMR TCH/H Prior Cell Load Threshold Power Level / Power Type / Power Finetune BSPWRB / BSPWRT TCH Immediate Assignment CHAP SDCCH Dynamic Allocation Allowed ACLC Allow Dynamic Shutdown of TRX BTSPS ECSC ECSC MS_TXPWR_MAX_CCH MSTXPWR Interference Band Threshold (1-5) ITSIB (1-5) DHA/DYMA (Cell) Direct Retry AW Assign-optimum-level Threshold HCS IN / HCS OUT KPIs Name Huawei CDR (Incl HO) (CM33 + CM337)/(K3013A + K3013B)*100 CDR (Excl HO) (CM33 + CM337)/(K3013A)*100 CSSR (%) (1-(K3001/K3000))*(1-(K3011A/K3010A)) HOSR (%) (CH313:Successful Outgoing Internal Inter-Cell Handover+CH333:Successful Outgoing External Inter-Cell Handovers)/(CH311:Outgoing Internal Inter-Cell Handover Commands+CH331:Outgoing External Inter-Cell Handover Commands)*100 TCH Blocking (%) (k3011A/K3010A)*100 SDCCH Blocking (%) (K3001/K3000)*100 Ericsson (TFNDROP+TFNDROPSUB+THNDROP+THNDROPSUB)/(TFMSESTB+THMSESTB)*100 (TFNDROP+TFNDROPSUB+THNDROP+THNDROPSUB)/(TCASSALL)*100 (1-(CCONGS+CCONGSSUB/CCALLS)*(1- (CNRELCONG+TFNRELCONG+THNRELCONG+TFNRELCONGSUB+THNRELCONGSUB/TASSALL)) (HOVERSUC_TCR+HOVERSUC_TER)/(HOVERCNT_TCR+HOVERCNT_TER)*100 (CNRELCONG+TFNRELCONG+THNRELCONG+TFNRELCONGSUB+THNRELCONGSUB/TASSALL)*100 (CCONGS+CCONGSSUB/CCALLS)*100