0 penilaian0% menganggap dokumen ini bermanfaat (0 suara)
18 tayangan6 halaman
Adjusting the resistance for sensitivity of coin acceptance, turn clockwise for increasing and counterclockwise for decreasing. Set the COIN SW to "NO". D. Set the pulse of coin signal to "50MS".
Adjusting the resistance for sensitivity of coin acceptance, turn clockwise for increasing and counterclockwise for decreasing. Set the COIN SW to "NO". D. Set the pulse of coin signal to "50MS".
Adjusting the resistance for sensitivity of coin acceptance, turn clockwise for increasing and counterclockwise for decreasing. Set the COIN SW to "NO". D. Set the pulse of coin signal to "50MS".
Please read the manual carefully Please read the manual carefully Please read the manual carefully Please read the manual carefully before before before before operation operation operation operation Warning Warning Warning Warning
ADJUSTMENT FOR NEW KID COPTER Descriptions Step 1: Open the coin door and find the main board, DIP SW1 is on the main board
Step 2: Set the game according to the below setting chart: DIP SW1 SETTINGS 1 2 3 4 5 6 7 8 1 coin OFF OFF 2 coins ON OFF 3 coins OFF ON No. of Coin per Game 5 coins ON ON 60 seconds OFF OFF 90 seconds ON OFF 120 seconds OFF ON Game Time 180 seconds ON ON 120 seconds OFF OFF 180 seconds ON OFF 90 seconds OFF ON Wating Time Before Playing Background Music 60 seconds ON ON
Descriptions: A. remove the plastic coin from the coin sample chute and put a proper coin in it. B. remove the screws on the back of coin entrance. Adjust the fix chip of back of coin entrance according to the diameter of coin you will use so that it will prevent the large coin blocking the coin mech. C. set the COIN SW to NO. D. set the pulse of COIN signal to 50MS. E. following the drawing to adjust the resistance for sensitivity of coin acceptance, turn colckwise for increasing and counterclockwise for decreasing.
adjusting chip of entrance coin reject bar COIN signal wavelength adjusting SW COIN signal SW power/signal input micro-adjust resistance sample coin chute DC+12V S T R I C T S L A C K S e n s i t i v i t y + - C O I N R e m o v e R E P L A C E B a c k w a r d SW3 100ms SLOW 25ms FAST NOM normal MGN accurate 50ms MEDIUM WHITE COUNTER(+/-) GROUND N.C. SW1 SW2 N.O. COUNTER(-/+) COIN SIGNAL GRAY BLACK RED GRAY
Adjust the volume Step 1: Open the coin door and find the volume VR.
2. Turn the volume potentiometer to adjust the volume. Clockwisely turn the potentiometer to increase the volume; counterclockwisely will decrease the volume.
box for PCB NAME:BLYAOBAI IO PCB DIP ON 7 8 6 5 4 3 2 1 SW1 volume potentiometer
Troubleshooting:
# PROBLEM CAUSES SOLUTIONS No 12V voltage input in coin mech. Check the voltage input,output and connection of power board. Coin blocked in coin slot. Take out the blocked coin and decrease the distance of coin slot. No sample coin. Install the sample coin in coin mech. Sensitivity for coin passing through the coin mech is too high. Twist the resistor to right to adjust the sensitivity. Wire of START button is loose. Check the connection of START button. START button is bad. Replace the button. The copter does not reposition. Check the limit switch and connection of limit switch. Wire of limit switch is loose. Check the connection of limit switch. The limit switch is bad. Replace the limit switch. The copter runs too slowly. Ajust the oil circuit. Oil pressure is too low. Increase the oil pressure. Control circuit problem for copter running. Check the control circuit. START button has problem. Check the START button and its connection. Limit switch has problem Oil pressure control has problem. Check the motor and connection of oil control circuit. Wire of speaker is loose. Check the connection of speaker. Speaker is bad. Replace the speaker. Sound part on main board has problem. Repair or replace the main board. Sound button is bad. Replace the button. No voltage input for lights. Check the voltage input and connection of lights. Light is bad. Replace the light. No AC 110V/220V voltage input. Check voltage input and connection. No voltage output in power supply Repair or replace the power supply. Main board is bad. Repair or replace the main board. 5 No movement after powering on. 8 The lights can not work. 7 START button is invalid. 4 The copter does not move. The copter can not rise up or go down. 3 Check the connection of sound button. Wire of sound button is loose. can't insert coin 1 Check the limit switch and its connection. 2 No sound for shooting,bombin g. 6 No music.
S c h e m a t i c D i a g r a m :
coin input speaker 1+ speaker 1- speaker 2+ speaker 2- D I P S W
i n p u t
p o r t G N D K E Y 1 K E Y 3 K E Y 2 K E Y 4 K E Y 6 K E Y 5 motor control 9 1 8 1 5 +12V GND rise button drop button P D 5 P D 1 P C 6 P C 7 P C 1 P C 2 safety switch coin meter START light chasing light 1 chasing light 2 chasing light 3 chasing light 4 bomb button S T A R T