Anda di halaman 1dari 1

Product Technical Data Sheet

Rigips

Rimano

Uni
Version: 01.08.2013
The information in this Product Technical Data Sheet is based on our current knowledge and experience. It only represents general recommendations and due to the
large number of factors influencing the application and use of our products, it does not exempt the user from making tests and trials on his/her own. This document may
not entail guarantees with legal consequences in relation to certain product properties or the adequacy for practical use. The user shall abide by any potential protected
commercial rights and legal provisions at the expense thereof. All the information is provided in good faith and conscience, but may be subject to change.
Saint-Gobain Construction Products Romania - Rigips Business Unit
Str. Tipografilor 11-15, S-Park, Corp B3-B4, Sector 1, Bucuresti
Tel.: +40 (21) 207 57 50 www.rigips.ro


Product Description
Rimano Uni is a type of light gypsum
plastering for interior works,
mechanical application.
Intended Use
Rimano Uni is designed for the
mechanical interior plastering of the
brick, ACC, concrete walls, etc.
It is to be applied in thicknesses of up
to 40 mm.
Rimano Uni is recommended also for
the renovation and repair works, where
the plastering must be reconditioned.
It is recommended as a replacement
of the traditional plastering made of
three layers (grout, primer, base coat)
based on sanding cement.
Substrate
The substrate shall be clean, dust-
free, oil-free, unfrozen, dry and
protected from excessive moisture.
The highly absorbent areas (e.g.
ACC, brick) will be primed with Ri-
Kombigrund, for lowering their
absorption.
The glassy surfaces (e.g. the
concrete) shall be primed with Ri-
Kombikontact to ensure the cohesion of
the plastering on the wall/ceiling.
Application conditions
The temperature in the air, of the
material and substrate shall be above
+5C and below 35C.
Both in excessive heat conditions,
excessive ventilation and in excessive
cold conditions, the precincts where the
work is done or the freshly worked
areas shall be adequately protected.
Appropriate ventilation shall be
provided in the closed precincts for
drying the product.
Application
Marking and setting the screeds
In case screeds are used in the laying
of the plastering, we recommend you to
use the metallic T profiles protected
against corrosion by galvanizing or
aluminium T profiles.
They shall be fastened by means of a
gypsum grout (InstalGips or Construct
Gips are recommended).
The setting shall be made on the
entire length of the profile, in order to
avoid the bending of the profile.
Material Preparation
The water flow of the plastering
machine shall be adjusted so that the
hardness of the paste obtained allows
the easy levelling by using the lute, and
the material does not leak on the walls.
If the water pressure is low, you should
use an additional pump to compensate
this.
Method of Work
The paste is applied mechanically on
the substrate, continuously, without
leaving any unfilled spots.
The plastering surface shall be
levelled in successive stages until
obtaining a smooth area.
The working time of about 2 hours is
influenced by the absorption of the
substrate and the ambient temperature.
In the case of hot days, the material
applied will be sprinkled with plenty of
water.
It is applied in one layer, by observing
the mechanical application technology
for the gypsum plastering.
Rimano Uni does not need any
additional finishes (plasters), as a
smooth surface is obtained, prepared
for painting, tapestry, etc.
Tools required
Clean tools (lute, hawk, plaster hawk
and spatula) shall be used. The
gypsum or dirt from the pots and tools
shortens the time of setting of the
product.
The tools shall be cleaned with water
immediately after use.
Product storage and handling
Keep the product in a dry place, in
the original sealed packaging and
protected from bad weather.
The product is valid until the date
printed on the bag.
Occupational and Environmental
Protection Measures
Work with appropriate protective
equipment: safety goggles and a dust
mask.
Avoid the contact with the eyes (if
necessary, rinse with plenty of water
and seek medical advice), the
prolonged contact with the skin, the
ingestion / inhalation.
It is recommended to reduce the
forming of dust on the work site.
The waste from the packaging, and
those resulted from using the product
will be treated according to the legal
provisions in force.
Meet the recommendations made in
the Product Safety Data Sheet.
Technical Data
The product parameters presented
below refer to the temperature
requirements of 232C and the
relative humidity of the air of 505%.
Standard
under
EN 13279-1
Class B4
Composition
gray plaster,
aggregates and
additives
Fire reaction
class
A1
Finesses
99% under
1000m
Density approx. 650 g/l
Adhesion approx. 0.4 N/mm
2

Flexural strength approx. 1 N/mm
2

Compressive
strength
approx. 2 N/mm
2

Application time Approx. 120 min.
Mixing ratio
Guiding water flow:
650 l/h
Material
consumption
8 kg/sq.m/cm
Packaging (bag) 30 kg
Pallet 33 bags

Anda mungkin juga menyukai