Anda di halaman 1dari 2

Product Data

Product Data
Product Data Sheet
HEMPEL
HEMPELS EPOXY KNIFING FILLER 355SA
BASE 355S9 with CURING AGENT 955SA
Description: HEMPELS EPOXY KNIFING FILLER 355SA is a two-component, solvent-free, epoxy compound,
which - when fully cured - has excellent resistance to water, oil, solvents, impact and
abrasion.
Recommended use: As a filler for repairing cracks, damages and blowholes in concrete and steel surfaces.
The product is easy to work with and can be applied in thick coats (above 5 mm).
Meets FDA requirements.
Availability: Not included in Group Assortment. Local availability subject to confirmation.
PHYSICAL CONSTANTS:
Colours/Shade nos: Pastel blue/3010S
Finish: Semi-gloss
Volume solids, %: 100
Flash point: Non-flammable
Specific gravity: 1.6 kg/litre - 13.3 lbs/US gallon
Dry to touch: 2-3 hours at 20C/68F
Fully cured: 7 days at 20C/68F
The physical constants stated are nominal data according to the HEMPEL Group's approved formulas. They are
subject to normal manufacturing tolerances and where stated, being standard deviation according to ISO 3534-1.
APPLICATION DETAILS:
Mixing ratio for 355SA: Base 355S9 : Curing agent 955SA
1 : 1 by volume
Application method: Spatula, putty knife or similar
Thinner (max.vol.): Do not dilute
Pot life: 1 hour (20C/68F)
Cleaning of tools: HEMPELS TOOL CLEANER 99610
Recoat interval, min: 12 hours (20C/68F)
Recoat interval, max: 30 days (20C/68F)
Safety: Handle with care. Before and during use, observe all safety labels on packaging and
paint containers, consult HEMPEL Material Safety Data Sheets and follow all local or
national safety regulations. Avoid inhalation, avoid contact with skin and eyes, and do
not swallow. Take precautions against possible risks of fire or explosions as well as
protection of the environment. Apply only in well ventilated areas.
1/2
Issued: January 2005 Page 1 of 2
Product Data Sheet
SURFACE The surface must be sound and free from dust, loose paint, oil/grease and other contaminants.
PREPARATION: Metal: Remove oil and grease, etc. with suitable detergent. Remove salt and other contaminants
by (high pressure) fresh water cleaning. Abrasive blasting, power tool cleaning or sanding,
depending on material and condition of the surface. Finally clean the area with HEMPELS THINNER
08450. Priming after abrasive blast cleaning, but prior to filling, can be done with a thin layer of
e.g. HEMPADUR 15590.
Concrete: Remove slip agent and other possible contaminants by emulsion washing followed by
high pressure hosing with fresh water. Remove scum layer and loose matter to a hard, rough and
uniform surface, preferably by abrasive blasting, possibly by other mechanical treatment or acid
etching. Seal surface with suitable sealer, e.g. HEMPADUR SEALER 05990, prior to filling.
APPLICATION Use only where application and curing can proceed at temperatures above 5C/41F.
CONDITIONS: The temperature of the substrate should also be above this limit.
Apply only on a dry and clean surface with a temperature above the dew point to avoid
condensation.
PRECEDING None, or according to specification.
COAT:
SUBSEQUENT According to specification.
COAT:
REMARKS: Mix and stir the two components thoroughly until an even colour is achieved, whereafter the filler is
ready for use. Do not mix more than is necessary for use within the pot life.
If the maximum recoating interval is exceeded, roughening of the surface is necessary to ensure
intercoat adhesion.
May be sanded after 20 hours (20C/68F).
Note: HEMPELS EPOXY KNIFING FILLER 355SA is for professional use only.
ISSUED BY: HEMPEL PAINTS (SAUDI ARABIA) W.L.L. - 355SA3010SSA004

Issued: January 2005 Page 2 of 2
2/2
HEMPEL'S EPOXY KNIFING FILLER 355SA
This Product Data Sheet supersedes those previously issued.
For explanations, definitions and scope, see Explanatory Notes in the HEMPEL Book.
Data, specifications, directions and recommendations given in this data sheet represent only test results or
experience obtained under controlled or specially defined circumstances. Their accuracy, completeness or appro-
priateness under the actual conditions of any intended use of the Products herein must be determined exclu-
sively by the Buyer and/or User.
The Products are supplied and all technical assistance is given subject to HEMPEL's GENERAL CONDITIONS OF
SALES, DELIVERY AND SERVICE, unless otherwise expressly agreed in writing. The Manufacturer and Seller
disclaim, and Buyer and/or User waive all claims involving, any liability, including but not limited to negligence,
except as expressed in said GENERAL CONDITIONS for all results, injury or direct or consequential losses or
damages arising from the use of the Products as recommended above, on the overleaf or otherwise.
Product data are subject to change without notice and become void five years from the date of issue.

Anda mungkin juga menyukai