0 penilaian0% menganggap dokumen ini bermanfaat (0 suara)
939 tayangan2 halaman
Depower the system. For additional WARNING: Always wear safety glasses when handling an air bag Supplemental Restraint system (SRS) Remove the 4 pin-type retainers and the lower radiator air deflector severity sensors. Replace the sensor or any other damaged supplemental system components. Install, tighten to 12 Nm (9 lb-ft). The RCM fuse is removed and the ignition switch is removed.
Depower the system. For additional WARNING: Always wear safety glasses when handling an air bag Supplemental Restraint system (SRS) Remove the 4 pin-type retainers and the lower radiator air deflector severity sensors. Replace the sensor or any other damaged supplemental system components. Install, tighten to 12 Nm (9 lb-ft). The RCM fuse is removed and the ignition switch is removed.
Depower the system. For additional WARNING: Always wear safety glasses when handling an air bag Supplemental Restraint system (SRS) Remove the 4 pin-type retainers and the lower radiator air deflector severity sensors. Replace the sensor or any other damaged supplemental system components. Install, tighten to 12 Nm (9 lb-ft). The RCM fuse is removed and the ignition switch is removed.
Front Impact Severity Sensor Item Part Number Description Item Part Number Description 4 14B004 LH and RH front impact 1 W705589 Lower radiator air deflector severity sensors pin-type retainers (4 required) 5 LH and RH front impact 2 8349 Lower radiator air deflector severity sensor electrical 3 W505256- LH and RH front impact connectors (part of 14398) S437M severity sensor bolts (Continued) Copyright 2005, Ford Motor Company Last updated: 11/3/2005 2006 Explorer, Mountaineer, 10/2005 501-20B-2 501-20B-2 Supplemental Restraint System REMOVAL AND INSTALLATION (Continued) 1. Depower the system. For additional WARNING: Always wear safety glasses information, refer to Supplemental Restraint when repairing an air bag supplemental restraint System (SRS) Depowering and Repowering in system (SRS) vehicle and when handling an air the General Procedures portion of this section. bag module. This will reduce the risk of injury in the event of an accidental deployment. 2. Remove the 4 pin-type retainers and the lower radiator air deflector. WARNING: Vehicle sensor orientation is critical for proper system operation. If a vehicle 3. WARNING: The tightening torque of equipped with an air bag supplemental restraint the air bag front impact severity sensor system (SRS) is involved in a collision, inspect retaining nuts is critical for correct system the sensor mounting bracket and wiring pigtail operation. for deformation. Replace and properly position the sensor or any other damaged supplemental NOTE: Make sure the radiator support and restraint system (SRS) components whether or front impact severity sensor mating surfaces are not the air bag is deployed. clean and debris free. NOTE: Note position of locator tab on sensor WARNING: To reduce the risk of personal bracket for installation. injury, do not use any memory saver devices. Remove the front impact severity sensor bolt. NOTE: The air bag warning lamp illuminates when To install, tighten to 12 Nm (9 lb-ft). the RCM fuse is removed and the ignition switch is ON. This is normal operation and does not indicate 4. Disconnect the front impact severity sensor a supplemental restraint system (SRS) fault. electrical connector and remove the sensor. NOTE: The SRS must be fully operational and free 5. To install, reverse the removal procedure. of faults before releasing the vehicle to the customer. 6. Repower the system. For additional information, refer to Supplemental Restraint System (SRS) NOTE: Repair is made by installing a new part Depowering and Repowering in the General only. If the new part does not correct the condition, Procedures portion of this section. install the original part and carry out the diagnostic procedure again. 2006 Explorer, Mountaineer, 10/2005