Legal notice This manual, as well as the software and hardware described in it, is furnished under license and may be used or copied only in accordance with the terms of such license. The content of this manual is fur- nished for informational use only, is subject to change without notice and should not construed as a commitment by Kemper GmbH. Kemper GmbH assumes no responsibility or liability for any errors or inaccuracies that may appear in this book. Except as permitted by such license, no part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, recording, by smoke signals or otherwise without the prior written permission of Kemper GmbH. Kemper Proling Amplier is a trademark of Kemper GmbH. All other trademarks contained herein are the property of their respective owners. All features and specications subject to change without no- tice. (Rev January 7, 2013 5:27 PM). Copyright 2012-2013 Kemper GmbH. All rights reserved. www.kemperamps.com 3 Table Of Contents CabMaker User Manual 6 Getting Started Welcome Installation Getting started Transferring converted cabinets Some free cabinet responses to get you started Software Limitations Act responsibly 9 System requirements KEMPER PROFILING AMPLIFIER 4 5 CabMaker User Manual CABMAKER 6 Getting Started Welcome Thank you for downloading CabMaker. This application converts impulse response les into cabinet deni- tions for the Kemper Proler. This way you can incorporate impulse responses of speaker cabinets from the internet and elsewhere into your own Kemper Proler rigs. Installation OSX: Run the CabMaker installer. It creates a folder called Kemper Amps within the application folder. Within this folder, both the CabMaker application as well as the documentation can be found. Windows: Run the CabMaker installer. It creates a folder called Kemper Amps within the program les folder. Within this folder, both the CabMaker application as well as the documentation can be found. Getting started CabMaker supports conversion of multiple les; you can select as many les as you need within the le selector which opens at startup. Alternatively, drag impulse responses onto the program icon to start the conversion. In order to convert a le, simply open it up and follow the instructions. GETTING STARTED 7 Transferring converted cabinets CabMaker exports native .kipr les ready to be used with the Kemper Proler. In order to transfer the les from your computer, copy them to the USB stick you use to update the amp. In case you have not pre- pared a USB stick for that purpose so far, please refer to the Basic Manual for further instructions. 1. Copy all .kipr les exported by CabMaker to the Shared folder on your USB stick 2. Unmount the stick and plug it into the USB port of your amp. 3. Select the soft button External Storage and choose Import/Export followed by Import to transfer the new local presets. 4. Navigate to the CABINET edit page within the STACK section and browse through the new local cab pre- sets using the BROWSE knob. Some free cabinet responses to get you started The following websites; among many others, ofer free speaker cabinet impulse responses to get you started: http://bedroomproducersblog.com/2010/10/01/free-sample-shootout-6-best-free-guitar-cabinet-impulse- responses/ http://www.redwirez.com http://www.grecore.de/IR/content.html Please note that Kemper Amps is not afliated with the providers of the links above. We cannot guarantee their availability to you at any time. Software Limitations CabMaker requires the impulse response le to be wave les (.wav format), sampled at 44.1kHz and either 16 or 24 bits deep. Other le formats are not supported. The utility takes approximately the rst 1.5 sec- onds into account; since impulse responses are typically very short, this should prove more than enough. You can literally take any type of signal and turn it into a cabinet; in most cases, this is unlikely to result CABMAKER 8 in a very usable cabinet, but feel free to experiment! Please note, however, that any signal which is not a proper impulse response will lead to an unpredictable result which might be anything from simply boring to downright unpleasant. Act responsibly CabMaker transcodes a wave le. This means that if you dont own the rights to a particular impulse re- sponse, you can probably use it yourself without consequence; however, you shouldnt redistribute it with- out prior permission from the original author. Please bear this in mind when you upload new rigs to the Rig Exchange on the Kemper Amps website. SYSTEM REQUIREMENTS 9 System requirements Mac: OSX 10.6 or higher and an Intel CPU Windows: Windows XP SP3 or higher. We recommend Windows 7 or higher. www.kemper-proler.com Copyrigh 2013 Kemper GmbH. All rights reserved. The information provided is subject to change without notice. All other trademarks are the property of their respective owners. Document Revision: 12/10/07 - A/EN Copyright 2012-2013 Kemper GmbH. All rights reserved. www.kemperamps.com